WORKSHOP. 1015HDDA, 1019HDDA m WALL HEIGHT 1015HDDA2, 1019HDDA2-2m WALL HEIGHT OPTIONAL SINGLE HINGED DOOR INSTRUCTION MANUAL INCLUDED

Transcription

1 DOUBLE HINGED DOOR WORKSHOP 1015HDDA, 1019HDDA m WALL HEIGHT 1015HDDA2, 1019HDDA2-2m WALL HEIGHT OPTIONAL SINGLE HINGED DOOR INSTRUCTION MANUAL INCLUDED (Available in Australia only) TRECO SHEDS ARE MANUFACTURED TO COMPLY WITH ALL AUSTRALIAN STANDARDS TR1519HDD - 08/05/07

2 BEFORE STARTING CONSTRUCTION The 10x15 and 10x19 sheds consist of three frame packs and two flat packs. 1015E or 1019E is the LONG FRAME C or C is the CENTRE A FRAME ( Portal Frame ) 1015B or 1019B is the SHORT FRAME Please do not mix the contents of the frame packs up as they look very similar but change in length. The easiest way not to mix them up is to place them on the foundation diagonally in order as above then open them and identify the parts. The large flat packs contain the sheeting etc for the shed. These can be opened up away from the foundation to identify the parts. NOTE The Optional Single Hinged Door (available in Australia only) is packed in the A or D Packs if it is unassembled or it will be in a separate box if it is assembled. Not all 1015 / 1019 models are provided with the Optional Single Hinged Door. This item is an extra if you require an Optional Single Hinged Door they are available from your local Treco Agent. If your shed contains the Optional Single Hinged Door Please read the installation instructions on page 27 BEFORE starting construction of the shed. Not all holes are pre-punched for hinged door construction, use the self tapping screws provided with a battery drill or pre-drill using a 2.8mm drill bit. NOTE Throughout this manual all doubled up codes refer to 10x15 shed code first followed by the 10x19 shed code. eg (B7/B9) B7= Short Side Base Rail for 10x15 shed B9 = Short Side Base Rail for 10x19 shed. Codes for sheds with 1.78m wall height may differ from codes with shed with a 2m wall height. Shed codes for 1.78m wall height will be followed by shed codes for 2m wall height. eg (K/K2) K = 1.78m wall sheet K2 = 2m wall sheet Pack A Pack D Pack C Pack B Pack E BEFORE YOU START, IT IS IMPORTANT THAT YOU READ THE FOLLOWING INSTRUCTIONS. When selecting a site, choose an area that is firm and level yet allows drainage away from the site. Although this shed when installed according to instructions, is designed to withstand greater wind loads than other conventional sheds, do not assemble it in areas subject to high winds or erect on a windy day. Any building left partially constructed may be seriously damaged if left in this state. It is your responsibility to safely and securely anchor the shed, having regard to the windiest conditions in the area. The shed could possibly blow away causing damage and possible injury if not properly attached to the ground foundation. Do not backfill against the walls or base of the shed as this will cause corrosion and void the warranty. The prevention of condensation inside the shed will assist in keeping the contents dry as well as minimising any possible corrosion of the shed itself, the following hints may prove useful. There is always dampness in soil, and this may rise into the shed if there is no barrier. A heavy duty polythene sheet may be placed under the concrete slab to prevent evaporation into the shed. Seal the space between the bottom frame and the concrete slab with a silicone. You will need a few tools, as indicated in the section HOW TO READ THIS MANUAL. Most holes for screws are predrilled. A power screw driver or cordless drill equipped with a magnetic Philips tip will hasten assembly. Take care not to over-tighten self-tapping screws. Sort, separate and identify all parts and hardware before construction. Check against the illustrations shown. Framing components are labelled. 1

3 INSTALLATION ADVICE Tools required All the tools listed are required for the erection of the shed. These tools should be at hand before starting work. 1. Step ladder 2. Masonary Drill Bit 6.5mm and suitable power drill 3. Tape measure 4. Cordless power screw driver 5. Phillips No. 2 Screwdriver tip 6. Dyna bolts 6.5mm x 40mm 7. Multi grips mm and 10mm Steel Drill Bit 9. Hacksaw or Tin Snips MODEL NO. APPROX. ROOF DIMENSIONS IMPORTANT SAFETY FEATURES OVERALL HEIGHT APPROX. BASE DIMENSIONS APPROX. FOUNDATION DIMENSIONS DYNABOLT 6.5mm x 40mm FE FEET ET MM FEET MM FEET MM FEET MM QTY 1015A 10' x 15' 3070 x " '8" x 14'8" 2960 x ' x 15' 3070 x A2 10' x 15' 3070 x " '8" x 14'8" 2960 x ' x 15' 3070 x A 10' x 19' 3070 x " '8" x 18'8" 2960 x ' x 19' 3070 x A2 10' x 19' 3070 x " '8" x 18'8" 2960 x ' x 19' 3070 x Observe all special notes which indicate differences between various types of sheds. You should not try to assemble the shed on your own. Get a second person to help you. The statutory requirements of the local building authorities must be observed. Safety gloves should be worn during assembly. Safety glasses should be worn during assembly. Preferably in a long sleeve shirt. Beware of sharp edges. WINTER SERVICE: The roof is designed for a snow load of 75 kg/m2. In order to avoid overload of the roof, timely removal of snow from the roof area is recommended. If the garden shed is unattended for lengthy periods during the winter months, the roofs should be propped up as a safety precaution. THE MANUFACTURERS CANNOT BE HELD RESPONSIBLE FOR ANY CONSEQUENCES DUE TO SHEDS THAT ARE NOT ERECTED PER INSTRUCTIONS OR FOR DAMAGE DUE TO WEATHER CONDITIONS OR ACTS OF GOD. PARTS MAY CONTAIN SHARP EDGES & CORNERS. CARE MUST BE TAKEN WHEN HANDLING VARIOUS PIECES TO AVOID AN ACCIDENT, FOR SAFETY SAKE, PLEASE USE A PAIR OF WORK GLOVES & EYE PROTECTION WHEN ASSEMBLING OR PERFORMING ANY MAINTENANCE ON THE BUILDING. 2

4 PARTS LIST CONTENTS OF PACK A (FLAT PACK) Qty 1015HDD2 (2M WALL) Qty 1015HDD (1.78M WALL) Qty 1019HDD2 (2M WALL) Right hand gable 2 O1 2 O1 2 O1 2 O1 Left hand gable 2 N1 2 N1 2 N1 2 N1 Qty 1019HDD (1.78M WALL) Hinged door 2 SCHDX2 2 SCHDX 2 SCHDX2 2 SCHDX Roof end panel 4 RQ1 4 RQ1 4 RQ1 4 RQ1 Door jamb 2 L62 2 L6 2 L62 2 L6 Door jamb supporter 2 HD52 2 HD5 2 HD52 2 HD5 K frame 2 H1270A 4 H4A 2 H1270A 4 H4A K frame 2 H4A H4A - - Top door support 1 C C C C1525 Gable base rail ( split ) 2 A6 2 A6 2 A6 2 A6 Roof panel 6 S1 6 S1 6 S1 6 S1 Wall panel 9 K2 9 K 9 K2 9 K Full corner panel 4 F2 4 F 4 F2 4 F Hardware kit bag Corner gusset 4 X20 4 X20 4 X20 4 X20 Gable - door track bracket 2 X26 2 X26 2 X26 2 X26 Gable - roof beam bracket 4 X15A1 4 X15A1 4 X15A1 4 X15A1 Portal - roof beam bracket 4 X15 4 X15 4 X15 4 X15 Portal anchor bracket 2 TR01074A 2 TR01074A 2 TR01074A 2 TR01074A Rafter bracket 4 X34 4 X34 4 X34 4 X34 Portal midwall bracket 4 PB2 4 PB2 4 PB2 4 PB2 Roof ridge end cap 2 X10 2 X10 2 X10 2 X10 Roof corner cap 4 X8 4 X8 4 X8 4 X8 Roof washer sheet 10 X11 10 X11 10 X11 10 X11 Padbolt 3 HA01000A 3 HA01000A 3 HA01000A 3 HA01000A Padbolt Spacer 2 HA01002A 2 HA01002A 2 HA01002A 2 HA01002A Hinge 9 HA01001A 9 HA01001A 9 HA01001A 9 HA01001A Self tapping screws Nuts and bolts 450 X X X X13 CONTENTS OF PACK D (FLAT PACK) Roof panel 8 S1 8 S1 12 S1 12 S1 Wall panel 8 K2 8 K 12 K2 12 K Skylight (optional minus 1 Roof Panel if in Kit) Sky10 Sky10 Sky10 Sky10 CONTENTS OF PACK C (MEDIUM LONG PACK) Portal frame column 2 PF12 2 PF1 2 PF12 2 PF1 Portal frame rafter 2 PF2 2 PF2 2 PF2 2 PF2 Portal frame sealing strip 2 PF3 2 PF3 2 PF3 2 PF3 Portal frame bottom chord 2 PF4 2 PF4 2 PF4 2 PF4 CONTENTS OF PACK HDE (LONG PACK) Gable top rail 1 I1 1 I1 1 I1 1 I1 Gable end midwall 2 RM1 2 RM1 2 RM1 2 RM1 Long roof beam 6 P8 6 P8 6 P1 6 P1 Long side base rail 2 B8 2 B8 2 B1 2 B1 Long side midwall 4 SM8 4 SM8 4 SM1 4 SM1 Long side top rail 2 H8 2 H8 2 H1 2 H1 CONTENTS OF PACK B (LONG PACK) Gable top rail 1 I1 1 I1 1 I1 1 I1 Gable base rail 1 A1 1 A1 1 A1 1 A1 Gable end midwall 2 RM1 2 RM1 2 RM1 2 RM1 Short roof beam 6 P7 6 P7 6 P9 6 P9 Short side base rail 2 B7 2 B7 2 B9 2 B9 Short side midwall 4 SM7 4 SM7 4 SM9 4 SM9 3

5 PARTS - PACK A Note: Packing procedures may differ for larger items in packs A & D however they will still contain the correct amount of parts. Models containing the optional skylight will consist of one less roof sheet. HARDWARE KIT BAG X8 X10 X11 X15 X13B NUT SELF TAPPING SCREW X34 X20 PB2 TR01031Q X13A BOLT HA01002A HA01000A HA01001A TR010074A X15A1 Packed separately FRAME IN PACK A C Top Door Support A6 - Gable Base Frame HD5/HD52 - Door Jamb Supporter H4A/H1270A - K Frame 4

6 PARTS - PACK A - Continued SCHDX/SCHDX2 - Door Roof Ends K/K2 - Wall Panel L6/L62 - Door Jamb RQ1 RQ1 N1 01 Gables S1- Roof Panel F/F2 - Corner Panel Packed in bottom of box PARTS - PACK D SKY10 - Skylight Optional S1 - Roof Panel K/K2 - Wall Panel 5

7 PARTS - PACK B A1 RM1 I1 P7/P9 T6 B7/B9 SM7/SM9 H7/H9 PARTS - PACK C PF4 PF1/PF12 PF2 PF3 PARTS - PACK E I1 RM1 P8/P1 B8/B1 SM8/SM1 H8/H1 U2 U3 6

8 FOUNDATIONS Roof Width = 3.07m 1015HDDA / 1015HDDA2 1019HDDA / 1019HDDA2 Roof Roof depth = 4.64m 1015HDDA 1015HDDA2 Roof depth = 5.88m 1019HDDA 1019HDDA2 Roof y Recommended Slab depth = 4.740m 1015HDDA 1015HDDA2 Recommended Slab depth = 5.980m 1019HDDA 1019HDDA2 X Recommended Slab width = 3.170m 1015HDDA / 1015HDDA2 1019HDDA / 1019HDDA2 Note: The foundation size recommended is 100mm wider than the shed roof. This gives an extra 50mm each side which prevents water from the roof digging a trench and splashing soil against the side of the shed. Check the table on page 2 for exact roof dimensions. Lay a heavy duty polythene sheet between the ground and the concrete to reduce condensation in the shed. X = Y 100mm Allow 7 days for concrete to cure C A L E N D A R S M T W T F S

9 WALL PANEL LAYOUT Note: Codes for sheds with 2m wall height may differ from codes with shed with a 1.78m wall height. eg K = 1.78m wall sheet as shown in 1015HDDA diagram K2 = 2m wall sheet as shown in 1019HDDA2 diagram As shown in the diagrams below the Double Hinged Doors can be placed on any side of the shed where there is a 3 Wall Panel K/K2 space. eg Under the Gables as shown in 1015HDDA diagram On long side as shown in 1019HDDA2 diagram F K K K K K K K F K PORTAL FRAME PORTAL FRAME Du cadre de portique L6 K K MODELS: 1015HDDA (shown) 1015HDDA2 DOOR DOOR PORTAL FRAME L6 F K K K K K K K F F2 K2 K2 K2 K2 K2 K2 K2 K2 K2 F2 K2 PORTAL FRAME K2 K2 MODELS: 1019HDDA 1019HDDA2 (shown) K2 K2 PORTAL FRAME K2 F2 K2 K2 K2 K2 K2 K2 L62 DOOR DOOR L62 F2 8

10 STEP 1 PRE-Assemble ALL PARTS IN STEP 1-8 before erecting shed. Fix Gables 'O1' and 'N1' to the Top Rail 'I1' from the centre towards each end with screws ''. Note If Double Hinged Doors are to be placed underneath the Gable fix 'X26' bracket to centre of Gable as shown in diagram below as this gives support to the Gable over the door opening. There is no 'X26' brackets required on the opposite Gable. If Double Hinged Doors are to be placed down the long side 'X26' brackets are not required. Fix together each Gable in the centre with Bolts 'X13A' and Nuts 'X13B'. N1 O1 I1 X13B Note: Do not fix '' to end holes X13A 'I1' has no holes facing inside of shed X26 Note: X15A1 (Long) Gable Brackets to be fixed to front and back gables. 9

11 STEP 2 - Roof Beams - P P7 3x P8 } For 10x15 P9 3x P1 } For 10x19 X13B P Note: Top holes for roof fixing must be parallel P X13A Note: The Roof Beams 'P' have THREE OVAL SLOTS AT EACH END not round holes as the Side Midwalls 'SM'. Do not fix nuts and bolts in these slots. Leave the three end slots of 'P's' empty on both ends for fixing on step 11. From the 'E' pack join together three pairs of Long Roof Beams (P8 for 10x15) or (P1 for 10x19) to make three Long Roof Beams 'P'. Ensure when joining the pairs together that the roof fixing holes are parallel on top of the Roof Beams as shown in the diagram. Always place the joined Long Roof Beams at one end of the foundation, so not get them mixed up with the Short Roof Beams. From the 'B' pack join together three pairs of Short Roof Beams (P7 for 10x15) or (P9 for 10x19) to make three Short Roof Beams 'P'. Ensure when joining the pairs together that the roof fixing holes are parallel on top of the Roof Beams as shown in the diagram. Always place the joined Short Roof Beams at the opposite end of the foundation, so not to get them mixed up with the Long Roof Beams. 10

12 STEP 3 - Side Midwall Brace - SM SM7 2x SM8 } For 10x15 SM9 2x SM1 } For 10x19 X13B P Note: Line up the four end holes X13A P Note: The Side Midwall Braces 'SM' have FOUR ROUND HOLES AT EACH END not oval slots as the Roof Beams 'P'. Do not fix nuts and bolts in these holes. Leave the four end holes of 'SM's' empty on both ends for fixing on step 13. From the 'E' pack join together two pairs of Long Side Midwall Braces (SM8 for 10x15) or (SM1 for 10x19) to make two Long Side Midwall Braces 'SM'. Ensure when joining the pairs together that the end round holes are lined up at each end of the Side Midwall Braces as shown in the diagram. Always place the joined Long Side Midwall Braces at the same end of the foundation as the rest of the frame from the 'E' Pack, so not get them mixed up with the Short Side Midwall Braces. From the 'B' Pack join together two pairs of Short Side Midwall Braces (SM9 for 10x19) or (SM7 for 10x15) to make two Short Side Midwall Braces 'SM'. Ensure when joining the pairs together that the end round holes are lined up at each end of the Side Midwall Braces as shown in the diagram. Always place the joined Short Side Midwall Braces at the same end of the foundation as the rest of the frame from the 'B Pack', so not to get them mixed up with the Long Side Midwall Braces. 11

13 STEP 4 - Gable End Midwall Brace - RM1 X13B 1x RM1 For } 10x15 10x19 P Note: Line up the two end holes P X13A Note: The Gable End Midwall Brace 'RM1' have TWO ROUND HOLES AT EACH END not four round holes as the Side Midwall Braces 'SM'. Do not fix nuts and bolts in these holes. Leave the two end holes of 'RM1' empty on both ends for fixing on step 13. From the 'E' and 'B' Packs join together two pairs of Gable End Midwall Braces 'RM1's' to make two Gable End Midwall Braces 'RM1'. Ensure when joining the pair together that the end round holes are lined up at each end of the Back Midwall Braces as shown in the diagram. Always place each of the joined Gable End Midwall Braces at opposite ends of the foundation where the Gables are to be. 12

14 STEP 5 - Base Rails NOTE Throughout this manual all doubled up codes that refer to 10x15 shed code first followed by the 10x19 shed code. eg (B7/B9) B7= Short Side Base Rail for 10x15 shed B9 = Short Side Base Rail for 10x19 shed. Gable End Base Rail A1 X20 B7/B9 A1 X20 Overlap the Gable End Base Rail 'A1' on top of the Short Side Base Rail 'B7/B9'. Fix the Corner Gusset 'X20' using three '' Screws. SHORT SIDE BASE RAIL (B7/B9) X20 LONG SIDE BASE RAIL (B8/B1) Leave gap of approx 150mm between Long Side and Short Side Base Rail for the Portal Frame. X20 A6 + A6 = A1 X20 Join the two 'A6' Gable Base Rails from 'Pack A' by overlapping the two end wall holes to make one 'A1' Gable Base Rail. Wall holes Outside View A6 Step 2 Fasten self tapping screws '' into the top of the 'A6' anywhere in the overlap. A6 2 A6 Outside View A6 1 3 Step 1 Fasten screws '' in the overlapped wall holes first. Step 3 Remove ' s' from Step 1 when installing wall panels. 13

15 STEP 6 - Portal Frame PF1 = 1.78m Wall Height PF12 = 2m Wall Height X13A 1 2 Note: Repeat 1-4 on both sides of 'PF2'. PF2 PF2 5 X13B PF1/PF12 X34 3 PF2 PF4 PF2 PB2 6 PB2 4 PF2 PF2 Note: Repeat 5-6 on second 'PF1/PF12'. PF1/ PF12 X15 TR01074A PF4 X15 7 X15 Side profile of PF2 PF2 PF4 PF1/PF12 PB2 PF4 X15 PF1/PF12 TR01074A PB2 14

16 STEP 7 - Corner Panels and Portal Frame Corners 'F/F2' are supplied with a 45 bend. With a supporter (any sized straight edge that is longer than the panel NOT SUPPLIED) bend the panels 90 manually. (Do not over bend). F/F2 F/F2 2 H7/H9 F/F2 Corner Panel A1 Gable End Base Rail Supporter H = Top Rail Curved side of H rail is for roof fixing, flat side for wall fixing 1 H8/H1 H8/H1 PORTAL FRAME Note: When fastening corner panels attach screws in order as shown. 4 F/F2 Corner panel 1 Fix Corner Panel F/F2 with the long side to be fastened to Gable End Base Rail A1. 2 Attach Short Top Rail H7/H9 to the Corner Panel. This will stabilise panels when attaching Portal Frame. 3 A1 Gable End Base Rail 3 Fix the opposite corner panel F/F2 to opposite Gable End Base Rail A1. 4 Attach Long Top Rail H8/H1 to the Corner Panel. This will stabilise panels when attaching Portal Frame. 1 F/F2 5 6 Repeat steps 1-4 on the other side. Place pre-assembled Portal Frame in centre of the shed as shown in the diagram

17 STEP 8 - Wall Panels and Gables Note: The wall panel overlaps the PF1/PF12 towards the long side by half a panel as shown in diagram 1. Please study the screw fixing procedure in step one closely. You may need to squeeze the bottom of the PF1/PF12 to line it up with the holes in the PF3 correctly Fix screws through bottom of the wall panel-'k/k2', 'PF3', (PF1/PF12) and into the Base Rails -(B7 and B8) or (B9 and B1) Fix screws through top of the wall panel - 'K/K2, 'PF1, (PF1/PF12) and into the Top Rail - (H7 and H8) or (H9 and H1) Repeat 1 and 2 on both sides Fix pre-assembled Gables to front and back of shed. 2 3 H8/H1 PF1/PF12 PF2 H7/H9 I1 B7/B9 H8/H1 K/K2 1 PF3 B8/B1 PF3 Short Side Base Rail B7/B9 PF1/PF12 B8/B1 Long Side Base Rail K/K2 16

18 STEP 9 - Wall Panels and Midwalls NOTE The Double Hinged Door can be placed on any side of the shed where there is a three wall sheet gap between the corner panels or the portal frame. Do not fix the Midwall to the shed where the Double Hinged Doors are to be placed until STEP 10. To attach the Long Side Midwalls 'SM8 = 1015', 'SM1 = 1019'. Slide one end of the pre-assembled Long Side Midwall over the Portal Midwall Bracket 'PB2' and fix a screw through the side of the Corner Panel 'F/F2' fixing the screw into the top half wall holes of the joined 'SM8/SM1'. The 'RM1' Midwall that is positioned under the Gables is to be fitted to the shed after the first Long Side Midwall is fitted as it slotted between the two halves of the Side Midwalls. Then the opposite Long Side Midwall can be slotted over the fixed 'RM1' and the Portal Midwall Bracket 'PB2' and fixed to the shed as done with the first Side Midwall. Repeat the same procedure with the Short Side Midwalls 'SM7 = 1015', 'SM9 = 1019' and the second 'RM1' at the other end of the shed. Note: Do not connect with nuts and bolts. This allows movement in the shed when fixing roof sheets. RM1 SM7 FOR 10x15 SM9 FOR 10x19 RM1 PF1/PF12 PB2 WALL PANEL FIXING SEQUENCE SM8 FOR 10x15 SM1 FOR 10x SM8/SM No washers 'X11' needed on wall panels Fix the Wall Panels 'K/K2' using screws in the fixing sequence shown in the diagram. When fixing the Wall Panels to the shed, start from the back of the side and continue sheeting laying them on top of each other towards the front. When you reach the previously fixed Wall Sheet at the portal frame and the Front Corner Panel underlap the Wall Panel to conceal all the seams and to give the appearence of the wall being one continuious form. 17

19 STEP 10 - Double Door Frame Construction Note. The diagrams below show construction of the door fame on the long side of the shed. Adjust codes if the door opening is to be placed elsewhere on the shed TOP VIEW Place rib of door jamb 'L6/L62' under rib of wall panel 'K2/F2' screw to Top Rail 'H8/H1' and Base Rail 'B8/B1'. FIX WITH THE SELF TAPPING SCREWS '' OR PRE-DRILL HOLES USING A 2.8mm DRILL BIT Cut Midwall K/K2 Place pre-assembled Midwall into position and mark where to cut using the diagram above. Cut with Hacksaw or Tin snips L6/L62 L6/L62 Door Jambs F/F2 Corner Panel L6/L62 Door Jambs K/K2 Wall Panel Attach cut midwalls SM to either side of the door opening with screws '' through the wall sheet then attach each end into either the RM1 or the PB2 with nuts and bolts. Only connect the two cut SM pieces. As this will not restrict movement in the shed when fixing the roof sheets. Do not connect any other SM's to RM1's or PB2's until Step 13. F/F2 L6/L62 RM1 PB2 Connect the cut 'SM1' with the 'RM1' with nuts & bolts CUT LONG SIDE MIDWALL 'SM8/SM1' 'PF1/PF12' Shown with no wall panel 'K/K2' for viewing purposes only. K/K2 L6/L62 K/K2 PB2 Connect the cut 'SM' with the 'PB2' with nuts & bolts CUT LONG SIDE MIDWALL 'SM8/SM1' 18

20 STEP 11 - Roof Beams Use nuts and bolts for step 11. Slide the pre-assembled Centre Roof Beams 'P' down over each side of the 'X34' on the Portal Frame and down over each side of the join in the gable. Fix the pre-assembled Centre Roof Beams 'P's into position using nuts and bolts in the end slots as in diagram 1, 2 and 3. Fix back centre 'P'. Following the instructions above as in diagram 3. Fix pre-assembled Side 'P's down over each side of the 'X15A1's on the gables and the X15's on the portal frame. 3 GABLE END Pre-assembled Centre Roof Beams 'P' Pre-assembled P7/P9 2 PF2 PF2 PF4 PF4 X34 Pre-assembled P8/P1 1 GABLE END END VIEW Pre-assembled Centre Roof Beams 'P' 19

21 STEP 12 - Roof End Panels All fasteners on roof need washers 'X11' attached. Fix all four Roof Ends 'RQ' with Bolts, Nuts and washers from top of appex to the side wall, as shown in diagram below. Fix screws & washers to roof beam(s) 'P' and side rails 'H'. Panel to Panel X13A X11 X11 X13B X13A Bolt, Washer & Nut Panel to Frame X13B P RQ1 X13A X13B Screw & Washer X11 Note: Please seal all unused pre-punched holes in the roof using bolts and nuts 'X13A + X13B' and plastic washers 'X11' supplied. RQ1 20

22 STEP 13 - Roof Panels If your shed model is supplied with the optional skylight use a metal Roof Panel 'S1' as a template and using the self tapping screws provided screw holes into the skylight. The skylight is designed to be fixed on top of the Roof Panels each side of it. Always start sheeting from the side that the skylight is to be positioned on. Start fixing the Roof Panels (screwing in the order shown) from one side at the back of the shed towards the front placing each panel on top of the previous. Then start sheeting from the back of the shed on the other side fixing one Roof Panel then fixing the Roof Capping 'U3/U2's' as you continue towards the front of the shed. Note The Long Roof Capping 'U3's' are to be placed at each end of the shed. The short Roof Capping 'U2' is to be placed between these as shown in the diagram below. Panel to 1 Panel Nut & Bolt X13A X SKY10 U3 U2 X11 X13B Panel to Frame X11 SM7 FOR 10x15 SM9 FOR 10x19 PB2 U2 PF1/PF12 U3 RM1 On completion of the roof join RM1 to SM's and SM's to PB2 with nuts and bolts. SM8 FOR 10x15 SM1 FOR 10x19 21

23 STEP 14 - Roof Edge Trim Fix the Roof Ridge End Cap 'X10' on top of the Roof End Capping 'U3'. To hide any joins, fix the Roof Edge Trim 'T6' to the roof starting from the back of the shed towards the front overlapping each Roof Edge Trim as you proceed. Fix the Roof Corner Caps 'X8' to each corner of the completed Roof Edge Trim. X10 X8 T6 X8 X8 X11 X13A X11 U2 X10 U3 X11 X13A X8 X13B T6 X13B 22

24 STEP 15 - Dyna-Bolting Base Rails to Concrete and sealing floor Ensure shed is square then drill 6.5mm holes into the foundation through the base rail where holes are provided. Fix 6.5mm x 40mm dynabolts. Do not seal shed before anchoring to foundation. X = Y 6.5mm x 40mm Dynabolt Before sealing the base rail ensure all dust has been removed. Place silicone inside the shed covering the gap of the inside edge of the base rail and the foundation. Side View Base Frame Silicone 23

25 STEP 16 - Door Assembly Note: When assembling double hinged doors ensure the K Frame is installed on opposite diagonals of each door to make a pair as in step 18. Drill 2.8mm holes where holes are not pre-punched. Hinged Door Kits vary from a non assembled door that needs to be fully constructed as in diagram 1-4. To a pre-assembled door that only needs the Hinges and K Frame 2-4. FRONT OF DOOR SIDE VIEW OF DOOR 1 2 FRONT OF DOOR C755 ALL DOOR TRIMS 'C' WITH LONG LIP ON INSIDE OF DOOR 875mm 985mm 150mm Hinge TRAH01001A Screws Centre PS750 Screws 875mm 985mm C1970 (2m) 150mm C1750 (1.78m) SCHDX1/SCHD Door Panel BACK OF DOOR C m Wall 2m Wall C FRONT OF DOOR Hinges 875mm 875mm 1.78m Wall 1060mm 910mm 2m Wall K Frame H4A mm = 1.78m WALL C mm = 2m WALL POSITION K-FRAME TO THE BACK OF THE DOOR EDGE TRIM AND SECURE WITH '' SCREWS AT EACH END.THEN FROM THE FRONT SIDE FIX SCREWS THROUGH THE DOOR PANEL INTO THE K-FRAME K Frame H4A mm = 1.78m WALL H4A mm = 2m WALL 24 Screws Screws

26 STEP 17 - Door Assembly continued Fix three self tapping screws or pre-drill three 2.8mm holes into the double door support 'C1525' then fix to the long top rail 'H' with '' screws as shown in diagram 1 and 2. Fix one door jamb supporter 'HD5/HD52' to the door jamb 'L6/L62' as shown in diagram 3. Fix the hinges on the door to the 'HD5/HD52' with '' screws. Slide the second 'HD5/HD52' over the other door jamb, screw second door to the 'HD5/HD52'. Adjust the door and the attached 'HD5/HD52' against the previously fixed door leaving a 2-3mm gap between the centre of the two doors. Attach the second 'HD5/HD52' to the Door Jamb. 1 Note 'C1525' is not needed when doors are place under the gables C1525 F/F2 L6/L62 HD5/HD52 L6/L62 K/K2 's 2 's 3 TOP VIEW HD5/HD52 L6/L62 F/F2 Screw FASTEN THE 'HD5/HD52' TO THE DOOR JAMB 'L6/L62' AT THE TOP AND THE BOTTOM THEN THE MIDDLE WITH SCREWS '' 25

27 STEP 18 - Door Assembly continued C1525 C1525 Padbolt Spacer HA01002A C1970 Padbolt HA01000A B Fix the Padbolt and Padbolt Spacer to the inside of the Door frame with '' Screws. Mark the 'C1525' (or 'A1' if doors under Gable) drill a 10mm diameter hole for the Padbolt shaft Internal padbolt spacer HA01002A K/K2 L6/L62 Door Trim View from inside of shed F/F2 L6/L62 A1 Padbolt Spacer HA01002A B Padbolt HA01000A Drill 10mm diameter hole for Padbolt shaft in base rail 'B'. Padbolt HA01000A Fix Pad Bolt 'HA01000A' to door supporter on the outside of the Door that isn't fixed with Padbolts on the inside. F/F2 L6/L62 L6/L62 K/K2 26

28 OPTIONAL SINGLE HINGED DOOR SINGLE HINGED DOOR 1.78m WALL HEIGHT 2m WALL HEIGHT TRECO SHEDS ARE MANUFACTURED TO COMPLY WITH ALL AUSTRALIAN STANDARDS TRX16SD - 08/05/07

29 PARTS LIST OPTIONAL SINGLE HINGED DOOR The Single Hinged Door Kit is the same size as Two Wall Sheets, therefore the A or D Packs will have Two Wall Panels less than stated on page 3. A Hacksaw or a pair of Tin snips is required to cut the Midwall for the optional hinged door installation. Not all holes are pre-punched, use the self tapping screws provided with a battery drill or pre-drill using a 2.8mm drill bit. The Optional Hinged Door kits are packed in the A or D Packs if it is unassembled or it will be in a separate box if it is assembled. Not all 1015 / 1019 models are provided with the Optional Hinged Door. This item is an extra if you require an Optional Hinged Door they are available from your local Treco Agent. ASSEMBLED DOOR PARTS LIST Qty 1.78m Wall 2m Wall Door Panel 1 TRSCHDX TRSCHDX2 Door Jamb 2 L1 / L8 L12 / L82 ¼ Wall Panel 1 K4 K42 Door Jamb Supporter 2 HD5 HD52 K Frame 2 H4A H4A / C1270 Hinges 3 TRAH01001A TRAH01001A Padbolt 1 TRHA01000A TRHA01000A L1/L8/L12/L82 Single Door Jamb HD5/HD52 Door Jamb Supporter H4A/C1270 K Frame TRAH01001A Hinge TRHA01000A Padbolt TRSCHDX/TRSCHDX2 Assembled Door K42/K4 1/4 Wall Panel UNASSEMBLED DOOR PARTS LIST Qty 1.78m Wall 2m Wall Door Panel Unassembled 1 TRSCHDX1 TRSCHD Door Top / Bottom Door Trim 2 C755 C755 Door Side Door Trim 2 C1750 C1970 Padbolt Plate 1 PS750 PS750 Door Jamb 2 L1 / L8 L12 / L82 ¼ Wall Panel 1 K4 K42 Door Jamb Supporter 2 HD5 HD52 K Frame 2 H4A H4A / C1270 Hinges 3 TRAH01001A TRAH01001A Padbolt 1 TRHA01000A TRHA01000A TRSCHDX1/TRSCHD Door Panel Unassembled C1750/C1970 Door Side Door Trim C755 Door Top / Bottom Door Trim 27 PS750 Padbolt Plate

30 STEP 10a - Door Jamb construction for Optional Hinged Door The door can be placed on any side of the shed, by leaving out Two Wall Sheets when sheeting up the shed. The ¼ Wall Panel and the two Door Jambs are to be fixed to the shed while sheeting up the shed. This will give structual strength to the shed to counter the weight of the roof. Construct and hang the door after STEP 16. DRILL 2.8mm HOLES AND FIX WITH SELF TAPPING SCREWS '' Door Jambs can be fixed either side K4/K42 1/4 Wall Panel L1/L12 TOP VIEW Place rib of door jamb 'L' under rib of wall panel 'K/K2' screw to Top Rail 'H' and Base Rail 'B'. K/K2 Wall Panel L8/L82 Door jambs Cut Midwall K4/K42 1/4 Wall Panel L1/L12 K/K2 L8/L82 Place pre-assembled Midwall into position and mark where to cut using the diagram above. Cut with Hacksaw or Tin snips K/K2 Wall Panel L8/L82 'PF1/PF12' Shown with no wall panel 'K/K2' for viewing purposes only. Attach cut midwalls SM to either side of the door opening with screws '' through the wall sheet then attach each end into either the RM1 or the PB2 with nuts and bolts. Only connect the two cut SM pieces. As this will not restrict movement in the shed when fixing the roof sheets. Do not connect any other SM's to RM1's or PB2's until Step 14. Connect the cut 'SM' with the 'RM1' with nuts & bolts RM1 F/F2 K/K2 L8/L82 MIDWALL CUT AS IN DIAGRAM ABOVE K/K2 K4/K42 L1/L12 Connect the cut 'SM' with the 'PB2' with nuts & bolts PB2 MIDWALL 28

31 STEP 19 - Construction of Optional Single Hinged Door Single Hinged Door Kits vary from a non assembled door that needs to be fully constructed as in diagram To a pre-assembled door that only needs the Hinges and K Frame 2-4. FRONT OF DOOR SIDE VIEW OF DOOR 1 2 FRONT OF DOOR C755 ALL DOOR TRIMS 'C' WITH LONG LIP ON INSIDE OF DOOR 875mm 985mm 150mm Hinge TRAH01001A Screws Centre PS750 Screws 875mm 985mm C1970 (2m) 150mm C1750 (1.78m) SCHDX1/SCHD Door Panel BACK OF DOOR C m Wall 2m Wall C FRONT OF DOOR Hinges 875mm 875mm 1.78m Wall 1060mm 910mm 2m Wall K Frame H4A mm = 1.78m WALL C mm = 2m WALL POSITION K-FRAME TO THE BACK OF THE DOOR EDGE TRIM AND SECURE WITH '' SCREWS AT EACH END.THEN FROM THE FRONT SIDE FIX SCREWS THROUGH THE DOOR PANEL INTO THE K-FRAME K Frame H4A mm = 1.78m WALL H4A mm = 2m WALL 29 Screws Screws

32 STEP 20 - Hanging the Optional Hinged Door Fix one 'HD5/HD52' over the door jamb 'L' on the side you want the door to be hinged from either the (L1/L8) or (L12/L82). Fix the hinges on the door to the 'HD5/HD52' with Screws ''. Slide the second 'HD5/HD52' over the other door jamb and adjust against the door to allow a 3mm gap. Then fix the second 'HD5/HD52' to the door jamb. K4/K42 TOP VIEW L8/L82 HD5/HD52 L1/L12 HD5/HD52 L1/L12 K4/K42 Screw FASTEN THE 'HD52' TO THE DOOR JAMB 'L12/L82' AT THE TOP AND THE BOTTOM WITH SCREWS '' Screw L1/L12 K4/K42 HD5/HD52 Fix the Padbolt 'HA01000A' to the Padbolt supporter 'PS750' on the door. Then fix the locking mechanism of the Padbolt to the 'HD5/HD52'. K/K2 K4/K42 L1/L12 L8/L82 K/K2 30

33 FOR ALL TECHNICAL INFORMATION WARRANTY AND SPARE PARTS PLEASE CALL (02) This material is copyright C 2006 Oldfields Pty Ltd. Apart from any use as permitted under the Copyright Act 1968, all other rights are reserved. You may download, store in cache, display, print and reproduce the material in unaltered form only (retaining this notice, or links to it where they appear) for your personal, non-commercial use. You are not permitted to re-transmit, distribute or commercialise the information or material without seeking prior written approval from Oldfields Pty Ltd. Requests for further authorisation should be directed to: Copyright Administrator, Oldfields Pty Ltd, 8 Farrow Road, Campbelltown, NSW 2560 Australia. 10 YEAR WARRANTY In addition to any implied warranties as provided by the Trade Practices Act, Treco sheds are warranted for a period of 10 years from the date of purchase as follows: 1. Zinc and galvanised panel materials will not rust. 2. Coloured panel materials will not rust, check, crack, flake, peel or blister. This additional warranty is subject to the following qualifications and limitations: 1. The warranty Certificate (attached) must be completed and returned to Treco within 21 days of purchase. 2. Warranty only applies if shed is used solely as a domestic shed and installed in accordance with the Owner s Manual. 3. Warranty does not apply if shed is installed in ocean surf locations or severe industrial or unusually corrosive environments. 4. Warranty is for the benefit of the original purchase and is not transferable. 5. Warranty does not cover fasterners. 6. Warranty applies to the exclusion of all other representations, guarantees or warranties, express or implied otherwise required by applicable legislation. WARRANTY CERTIFICATE NAME... ADDRESS SHED MODEL No... WHERE PURCHASED (STORE & ADDRESS) I Use my Treco Shed primarily for: l Work Shop l Cubby House l Garden Shed (storage) l Pool Change Room l Other I choose a Treco shed over the others because:... OLDFIELDS PTY. LTD. A.C.N For Information on your local Oldfields Treco stockist - Phone: OLDFIELDS TRECO RESERVE THE RIGHT TO VARY DESIGNS AND MATERIAL SPECIFICATIONS WITHOUT NOTICE. TR1519HDD - 08/05/07