Assembly Instructions

Size: px
Start display at page:

Download "Assembly Instructions"

Transcription

1 10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: Hours: 9-5 Monday-Friday EST Package ships as shown

2 revised 06/20/09 Cedar Gazebo Assembly Instructions Please read through the entire manual before starting! Note: It is very important that you have a firm, level site for the structure. When using tools and ladders, always follow manufacturer s recommended safety guidelines! Tools Needed: Sharp Utility Knife 5/8 Socket Socket Wrench 5/8 Wrench Hammer Stapler Cordless Drill Ladder Tape Measure Hammer Flathead Screwdriver Level Additional Items Needed: Approximately 4-5 bundles of shingles When your kit arrives, it should look like this. Inspect the package for any damage that may have occurred during shipping - dented corners, punctured plastic, etc. If the package is damaged, alert HomePlace Structures immediately at

3

4

5 This assembly manual is to be used to assemble a HomePlace Structures 10 or 12 octagon cedar or vinyl gazebo. The 10 vinyl model was used to create this floor. Depending on unit that was purchased, some of the pictures shown will differ from your unit. Gazebo without floor Gazebo with floor Gazebo floor only Step 1: Gazebo kit should arrive as shown, depending on which unit was purchased. Place kit as close to site as possible. If your unit does not include a floor, please proceed to page 11. Floor Framing Assembly It is very important to build the floor on a firm, level surface. Step 2: Very carefully cut the packaging bands holding the boxes together. Step 3: Remove the lid of box including the pressure treated sub-floor pieces. Step 4: Remove the contents of the box and organize like parts together; set parts close to assembly location. Step 5: Use a tape measure to find and mark the location of the center of gazebo floor. page 01

6 Step 6: Locate the double floor joists with notch cut at one end. Step 7: Use the mark from step 5 and lay out double floor joists making sure to keep notched end up and towards center as shown. Step 8: Lay out the eight perimeter band boards as shown. Step 9: Align the edge of the band board with center of the double joist and attach each end using two 3 screws in the pre-drilled holes. Note: It is important that the top edges of the band board and joist are aligned flush. page 02

7 Step 10: Align corner of adjacent band board and attach using 3 screws in pre-drilled holes. Step 11: Repeat steps 9 & 10 until all band boards are installed. Step 12: Insert center connecting plates as shown. Note: If opening is tight, step on connecting plates to push them down. page 03

8 Step 13: Center double joist along edge of connecting plate and attach using 3 screws. Note: There may be some space between joist and connecting plate, but it should not exceed 1/4. Step 14: Repeat step 13 for each of the remaining double joists trying to keep an equal space between the joist and connecting plate for each board. Floor is now ready for installation of middle joists. Step 15: Locate the 16 middle floor joists. Incorrect angle alignment 16: Place one middle joist in each floor section. Note: Make sure to properly align cut angles of joist. page 04

9 Step 17: Arrange middle floor joists to match pattern shown in picture. Step 18: Align joist with pre-drilled holes in band board. Step 19: Attach band board to middle joist using 3 screws in pre-drilled holes. Step 20: Attach middle joists to double joist using two 3 screws as shown. Step 21: Repeat steps for the remaining middle joists. page 05

10 Floor Board Installation Step 22: Open the box containing the floor boards. Step 23: Organize floor boards near floor framing as shown. Step 24: Place each of the outside floor boards around the perimeter of the floor. Step 25: Align floor board at center of double joist. Step 26: Attach floor board to floor framing using one 2-1/2 screw as shown. Note: It is recommended to put remaining screws in pre-drilled holes after each of the perimeter boards are in place. page 06

11 Step 27: Align opposite end of board with center of double joist. Step 28: Make sure the overhang is consistent along the entire edge of board. Step 29: Attach floor board using one 2-1/2 screw as shown. Step 30: Repeat steps and install adjacent floor board; attach using one 2-1/2 screw at each end. Step 31: Install remaining perimeter floor boards repeating steps page 07

12 Step 32: Lay out the next complete row of floor boards before attaching any. Step 33: Align boards with edges of floor joists. Step 34: Attach boards to floor joists using 2-1/2 screws. Note: There should be a 1/8-1/4 space between the rows. Step 35: Pre-drill one 3/16 hole above middle floor joist. Step 36: Attach floor boards to middle joist. Step 37: Repeat steps for remainder of floor boards in that row. page 08

13 Step 38: Repeat steps for each remaining row of floor boards. Step 39: Install center floor pieces as shown. Note: The center board may require additional force in order to make it fit. Step 40: Attach middle floor boards to sub-floor using 2-1/2 screws through pre-drilled holes. Floor board installation is complete. page 09

14 Band Board Trim Installation Step 41: Slide the first band board trim piece in place and align at center of floor corners. Step 42: Make sure trim piece is up tight against bottom of floor board. Step 43: Attach trim board to sub-floor using 1-1/2 screws in pre-drilled holes. Step 44: Align adjacent trim piece and attach repeating steps 41 & 42. Step 45: Repeat steps around perimeter of gazebo. page 10

15 Post & Bottom Railing Assembly Note angle of posts Note: When installing posts, angle at top of posts should slope down toward outside of gazebo. Step 1: Place package as close to assembly site as possible. Step 2: Carefully cut packaging bands. Step 3: Carefully cut open shrink wrap, making sure not to allow product to fall off of the skid. Step 4: Remove the posts and trim strips from package and organize. page 11

16 Step 5: Remove bottom railing box from the skid, place in close proximity to assembly site, and remove lid. Step 6: Remove top brace sections from package and organize. Step 7: Locate and open the box containing the railing spindles. Each railing section contains a top T-rail and bottom straight rail. Step 8: Locate one T-rail piece and one bottom straight rail and align angles. Step 9: Insert a railing spindle into each cutout in the bottom straight rail making sure each spindle is tight against bottom of cutout. page 12

17 Step 10: Make sure angles align on ends of railings. Step 11: Insert railing spindles into each cutout in T-rail making sure each spindle is tight against bottom of cutout. Step 12: Attach T-rail to spindles using three 1-1/2 screws in the predrilled holes along edge of T-rail. Step 13: Lay railing section on the ground and push together. Step 14: Attach the straight bottom rail to the spindles repeating step 13. Step 15: Repeat steps 8-14 for the six remaining railing sections. page 12

18 Step 16: Lay out one complete post trim and railing section including two post trim strips, one bottom railing section, and one top railing section as shown. Step 17: Locate the two spacer blocks included in the package. Step 18: Insert one spacer block under the bottom railing section. Step 19:Use the remaining spacer block to space the bottom of railing from the bottom of the post trim. Step 20: Attach post trim to bottom straight rail using two 2-1/2 screws in the pre-drilled holes. Step 21: Repeat steps on opposite side of railing. Step 22: Attach post trim to T-rail using 2-1/2 screws in pre-drilled holes for each side.

19 Step 23: Use the spacer blocks to align the brace section. Make sure short point at top of post trim is against the ground. Step 24: Attach the post trim to the top brace section using four 2-1/2 screws in the pre-drilled holes as shown. Step 25: Repeat steps for opposite side. Section is complete Step 26: Repeat steps for six remaining sections. Step 27: Assemble one door section without bottom railing as shown. Step 28: Stand up one post at door way opening keeping the angled cut sloping downward toward outside of the gazebo. Step 29: Position doorway section at appropriate location for your site. page 14

20 Step 30: Rest the post trim on top of the post and pull down tight as shown. Incorrect Correct Step 31: Center the post trim on the post as shown. Step 32: Attach the post trim to the post using five 2-1/2 screws in the pre-drilled holes. Step 33: Repeat steps for adjacent doorway post. page 15

21 Step 34: Install the remaining posts and railing sections repeating previous steps. page 16

22 Step 35: Center posts on floor splice and space an equal distance from edge of floor. Note: If you did not purchase the optional floor kit, space posts equally and attach to the foundation using appropriate fasteners. All posts should be positioned an equal distance from one corner of the gazebo to the opposite corner. Step 36: Center foundation bracket and fasten to each post using 2-1/2 screws, then attach post bracket to floor or foundation using appropriate fasteners. Note: Use 2-1/2 screws, if foundation is wood or composite material. If foundation is concrete or other hard surface, use hard surface fasteners purchased separately.. Rafter Installation Step 37: Remove rafter box from skid and unpack components. page 17

23 Step 38: Place a step ladder in the center of the gazebo. Step 39: Prepare roof bolts by putting a nut and washer on one end of each bolt as shown. Step 40: Slide the rafter into the slot at the top of the post as shown. Step 41: Align the hole in the rafter with hole on the post and push a bolt through. Step 42: Put a washer and nut on the opposite end of the bolt and tighten by hand. Step 43: Install rafter on opposite side repeating steps page 18

24 Step 44: Push compression block into place, pull bottom of rafters tight against lip, and attach using 2-1/2 screws through pre-drilled holes as shown. Step 45: Repeat steps for next set of rafters as shown. Step 46. Install 4 remaining rafters repeating previous steps as shown. page 19

25 Roof Band Board Installation Step 47: Insert four 2-1/2 screws in the pre-drilled holes in each band board. Step 48: Align band board with top of rafter and at the center of the rafter splice and attach to rafters. Step 49: Align opposite end of band board and attach. Step 50: Align adjacent board. Step 51: First attach adjacent band board at opposite corner. Step 52: Pull band board into place, align with first rafter, and attach. Step 53: Continue installing band boards around entire perimeter of gazebo. page 20

26 Roof Board Installation Step 54: Tighten acorn nuts with tools before installing roof boards. Step 55: Locate box containing roof boards, open box, remove parts, and organize as shown. Step 56: Center roof board at rafter splice, align flush with edge of band board, and attach using 2 nails. Step 57: Slide groove of next roof board into the tongue on the previously installed board and attach with two nails at each end as shown. Step 58: Repeat step 57 until entire section is complete. page 21

27 Step 59: Repeat steps for each roof section. Face Board Installation Step 60: Align top of face board flush with top of band board and at center of edge of corner splice. Attach face board using 2 trim nails. Step 61: First align and attach adjacent face board at opposite corner. Step 62: Align corners of face boards and attach to band board. Step 63: Continue installing face board around perimeter of gazebo.

28 Felt Paper Installation Step 64: Attach felt paper to roof boards using a hammer stapler as shown. Roof Bracket Installation Step 65: Center the bottom point of roof bracket and fasten to roof using 10d nails as shown. Note: Make sure nails go into rafters and 2x4 face board and do not protrude through bottom of ceiling/roof boards. Flower Box Installation Step 66: Install flower boxes where desired using 2 screws. page 23

29 Installation Instructions screen package for wood & vinyl octagon gazebos Toll Free: Hours: 9-5 Monday-Friday EST revised 8/12/09

30 TOOLS NEEDED: 1. Hammer 2. Utility Knife 3. Measuring Tape 4. Screw Gun Note: This manual was created to provide screen installation instructions for HomePlace Structures wood and vinyl octagon gazebos. Depending on the unit that was purchased, some of the pictures shown will differ from your unit.

31 Screen Panel Installation 1-13/16 Step 1: Remove screen panels from box and set to the side. Lay out one panel section as shown. Step 2: Mark bottom of screen panel in 1-13/16 from each end. Step 3: Tap in narrow filler strip along bottom of panel, and align with marks. Note: Steps 2 & 3 are not applicable to wood units. 3/4 Tip: Insert factory edge into screen panel for easiest installation. Step 4: Mark top of screen panel 3/4 from each end. Step 5: Tap in wide filler strip along top of panel, and align with marks. Step 6: Install screen panel by sliding top in as shown. Step 7: Slide bottom of screen panel in place and push snug against post as shown. Step 8: Repeat previous steps to install remaining six screen panels. Page 01

32 L-Strip T-Strip Step 9: Install trim strips onto center of post and fasten with 2-1/2 screws through pre-drilled holes. Do not countersink screws too deep, install just beyond surface. Screen Door Installation Note: There are 2 L strips for both sides of door, and 6 T strips for remaining posts. If you are installing screens for a wood gazebo, please see the instructions on page 5 for steps 10 & 11. Step 10: Install filler strip above door and fasten with 2-1/2 screws as shown. Step 11: Install plastic door jamb strip and fasten with 2-1/2 screws as shown (flush with outside of post). Page 02

33 Step 12: Install aluminum Z-strips on sides of door using 5 pan head screws per side as shown. Note: It is important to install side Z-strips first. Step 13: Install top Z-strip using pan head screws. Note: Z-strip corners should align as shown in picture. Page 03

34 1/8 Gap Step 14: Insert piano hinge into Z-strip and fasten with pan head screws into pre-drilled holes. Note: Make sure notched section of piano hinge is at bottom of door. Step 15: Slide door into piano hinge starting at top and working to bottom. Step 16: Align top of door with top of piano hinge. Step 17: Adjust door for correct reveal at top and fasten with 4 or 5 self-tapping screws. Step 18: Install bottom sweep onto bottom of door and adjust to desired height. Note: No screws are needed for this piece. Page 04

35 Additional Instructions for a wood gazebo Note: The following instructions replace steps 10 & 11 on page 2. A: Locate the door header boards. B: Interlock boards together and align flush at end. C: Insert boards above door header and attach with three 2-1/2 screws. D: Locate the door filler strips. E: Insert the top filler strip as shown and attach using three 2-1/2 screws as shown. F: Align the side filler strips flush with edge of post trim and attach to post using five trim nails per strip. Page 05

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models

Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

Octagon Vinyl Gazebo Assembly Instructions

Octagon Vinyl Gazebo Assembly Instructions Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly

More information

10 Octagon Cedar Gazebo Assembly Instructions

10 Octagon Cedar Gazebo Assembly Instructions 10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions

More information

The Festival Assembly Instructions

The Festival Assembly Instructions The Festival Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown CONTACT INFORMATION: HomePlace Structures 301 Commerce Drive New

More information

Pacifica Pool House. Assembly Manual. Toll Free: Hours: 9-5 Monday-Friday EST. Package ships as shown. Suncast Corporation

Pacifica Pool House. Assembly Manual. Toll Free: Hours: 9-5 Monday-Friday EST. Package ships as shown. Suncast Corporation Pacifica Pool House Assembly Manual Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST Package ships as shown Simpson Hurricane Straps Double Insulated Raised-Panel Door in back wall (71 x71 Total opening)

More information

KIT ASSEMBLY INSTRUCTIONS

KIT ASSEMBLY INSTRUCTIONS KIT ASSEMBLY INSTRUCTIONS We have designed these instructions as a stepby step procedure to simplify the assembly process. Nevertheless, we do recommend including someone with carpentry expertise on your

More information

V nyl Gazebo truct c it Assembly Instr ons

V nyl Gazebo truct c it Assembly Instr ons V nyl Gazebo Vi Assembly Instr ct tr t u ru ons ct c i ti Pre-assembly Instructions A C B #1 - Site properly prepared. 4" - 6" clean stone 9 linear blocks 2" x 8" x 16" C C A A B B #1a - 12" sauna tubes,

More information

Keystone Garage Assembly Manual

Keystone Garage Assembly Manual Keystone Garage Assembly Manual 14x24 Garage Kit ships as shown Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST 13 8 deep AMISH ORIGINAL KEYSTONE 14x24 GARAGE s p e c i f i c a t i o n s Optional

More information

Dodecagon Gazebo. Assembly Manual. If you are in the middle of your project and you need assistance Call (717)

Dodecagon Gazebo. Assembly Manual. If you are in the middle of your project and you need assistance Call (717) Dodecagon Gazebo Assembly Manual If you are in the middle of your project and you need assistance Call (717) 351-9250 Gazebo Assembly Manual Thank you for your purchase of this Gazebo. This manual is designed

More information

Sunhouse. Assembly Manual

Sunhouse. Assembly Manual Sunhouse Assembly Manual Thank you for your purchase of this sunhouse. Sunhouse Assembly Manual This manual is designed to simplify the assembly process, however we recommend having an experienced carpenter

More information

Oval Vinyl Gazebo. Assembly Manual

Oval Vinyl Gazebo. Assembly Manual Oval Vinyl Gazebo Assembly Manual Gazebo Assembly Thank you for your purchase of this Gazebo. This manual is designed to simplify the assembly process, however we strongly recommend having an experienced

More information

CAUTION: Before opening the crate place it flat on its side (not up right as show in the photo) Hardware included for assembling your gazebo:

CAUTION: Before opening the crate place it flat on its side (not up right as show in the photo) Hardware included for assembling your gazebo: Octagon Wood Gazebo Kit Contents Hardware included for assembling your gazebo: 5/16" Lag Bolts Use to fasten post to floor 2 1/2" screws Use to fasten joist together fasten posts to outside joist fasten

More information

AMISHGAZEBOSHOP.COM VINYL GAZEBO KIT CONTENTS

AMISHGAZEBOSHOP.COM VINYL GAZEBO KIT CONTENTS VINYL GAZEBO KIT CONTENTS Hardware for assembling your gazebo (provided): 2 1/2" screws Use to fasten joist together fasten posts to outside joist fasten rafters to rafter header fasten benches & cupola

More information

Artisan Vinyl Pergola

Artisan Vinyl Pergola Artisan Vinyl Pergola Assembly Manual Thank you for your purchase of this Pergola. Beefy Vinyl Pergola Assembly Manual This manual is designed to simplify the assembly process, however we recommend having

More information

Vinyl Gazebo Instructions

Vinyl Gazebo Instructions P a g e 1 Vinyl Gazebo Instructions 10 Vinyl Gazebo Shown Thank you for the purchase of your New Gazebo. Depending on the size of your Gazebo, installation can usually be completed in 1 to 2 days. These

More information

Renaissance Pavilion. Assembly Manual

Renaissance Pavilion. Assembly Manual Renaissance Pavilion Assembly Manual Thank you for your purchase of this pavilion. Renaissance Pavilion Assembly Manual This manual is designed to simplify the assembly process, however we recommend having

More information

Gambrel Barn Construction Manual 8x8 through 16x24 Units

Gambrel Barn Construction Manual 8x8 through 16x24 Units Gambrel Barn Construction Manual 8x8 through 16x24 Units Tools Needed: Cordless drill (12V or higher) #2 square drive bit Hammer 6 step ladder Tape measure Square utility knife w/ blade & hook blade Little

More information

Country Cabin. Assembly Manual. HomePlace Structures

Country Cabin. Assembly Manual. HomePlace Structures Country Cabin Assembly Manual Country Cabin Assembly Manual revised 3/20/10 Dear Customer, Thank you for your purchase of our Country Cabin. The craftsmanship and detail in this building is unmatched.

More information

12ft Octagon Bayside Gazebo Assembly Manual

12ft Octagon Bayside Gazebo Assembly Manual We recommend reviewing this Assembly Manual thoroughly before starting this project. Become familiar with the tools required and where and when assistants are necessary. If you re planning on finishing

More information

Best Barns USA. the Brookhaven 10' x 16' Assembly Book. revised March 23, 2016

Best Barns USA. the Brookhaven 10' x 16' Assembly Book. revised March 23, 2016 Best Barns USA Assembly Book revised March 23, 2016 the Brookhaven 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.

More information

Gambrel Barn with Overhang Manual

Gambrel Barn with Overhang Manual Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH

More information

10ft Octagon Bayside Gazebo Assembly Manual

10ft Octagon Bayside Gazebo Assembly Manual We recommend reviewing this Assembly Manual thoroughly before starting this project. Become familiar with the tools required and where and when assistants are necessary. If you re planning on finishing

More information

Assembly Instructions 10 X 10 Aluminum Roof Support

Assembly Instructions 10 X 10 Aluminum Roof Support Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1

More information

Octagon Greenhouse Manual

Octagon Greenhouse Manual Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Utility knife w/ blade & hook blade -Speed Square -5/16 Wood Drill bit Little Cottage Co. PO Box

More information

Shetland Stalls Installation Instructions

Shetland Stalls Installation Instructions Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front

More information

12ft Octagon (Precut) Creekside Gazebo Assembly Manual

12ft Octagon (Precut) Creekside Gazebo Assembly Manual 12ft Octagon (Precut) Creekside Gazebo Assembly Manual Aug 1st, 2008 Revision #9 In Florida, additional hardware may be required that is not included in kit due to hurricane winds. Please check with local

More information

VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS

VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS P a g e 1 VINYL CLASSIC FREESTANDING PERGOLA ASSEMBLY INSTRUCTIONS Shown: 8' x 12' Vinyl Classic Pergola with 12" Top and Main Runner Spacing The design of this pergola is based on all posts being installed

More information

Shed Assembly Instructions

Shed Assembly Instructions Shed Kit Contents The shed kit includes all the parts needed to assemble your shed except for tools and fasteners such as screws and nails. The various pieces are pre-cut and many are marked to indicate

More information

8x12 SpaceMaker Garden Shed Assembly Manual

8x12 SpaceMaker Garden Shed Assembly Manual 8x12 SpaceMaker Garden Shed Assembly Manual Version #6 Revised June / 2007 Thank you for purchasing a 8x12 SpaceMaker Garden Shed. Please take the time to identify all the parts prior to assembly. Safety

More information

Installation Instructions

Installation Instructions Installation Instructions Follow these simple instructions to install your OneDayCab! IMPORTANT: Unpack and check shipment for damage. Verify color, size and parts before demolition. Installation of interiors

More information

RangerWare Fiberglass Door System Installation Instructions P/N

RangerWare Fiberglass Door System Installation Instructions P/N Page 1 of 9 RangerWare Fiberglass Door System Installation Instructions P/N 2878016 ORDER OF INSTALLATION Note: To assure proper order, read all Accessory Installation Instructions before beginning. 1.

More information

Frameless Inline Door QCI5250

Frameless Inline Door QCI5250 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5250 FRAMELESS PANEL / DOOR / PANEL QCI0249 REV. 3 Page 1 Certified 10/12/12 Parts List with pivot hinges *Quantities may vary. QCI0249 REV. 3 Page 2

More information

Best Barns USA. Regency Deluxe. 8' x 12' Assembly Book. revised February 15, 2017

Best Barns USA. Regency Deluxe. 8' x 12' Assembly Book. revised February 15, 2017 Best Barns USA Assembly Book revised February 15, 2017 Regency Deluxe 8' x 12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive, Greenville, PA 16125 This manual is copyrighted. Under

More information

Precut Workshop & Gable Manual

Precut Workshop & Gable Manual Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH

More information

Precut Value Shed Manual Gambrel Barn

Precut Value Shed Manual Gambrel Barn Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised August 17, 2017 the Roanoke 16'x32' Building w/ full loft Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted

More information

Frameless Heavy Glass Door with Header

Frameless Heavy Glass Door with Header INSTALLATION INSTRUCTIONS Frameless Heavy Glass Door with Header QCI5243 QCI5243 REV. 0 Page 1 Certified 06/16/16 Frameless Heavy Glass Door with Pivot Hinges ITEM NUMBER DESCRIPTION QUANTITY 1 DOOR GLASS

More information

Sliding Glass Door Assembly and Installation Guide

Sliding Glass Door Assembly and Installation Guide Sliding Glass Door Assembly and Installation Guide Index Door System Components and Hardware The following components are needed to complete the installation of your Sliding Patio Door unit. Check all

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised September 19, 2017 the Millcreek 12'x 20' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the

More information

Series 1100 Aluminum Door Canopy

Series 1100 Aluminum Door Canopy Series 00 Aluminum Door Canopy with Support Arms It is our recommendation that you read instructions carefully prior to assembly and installation. Series 00 with Support Arms MOUNTING BAR (A) TOP TRIM

More information

8x4 SpaceSaver Garden Shed Assembly Manual

8x4 SpaceSaver Garden Shed Assembly Manual 8x4 SpaceSaver Garden Shed Assembly Manual Revision #8 July 5, 2010 Thank you for purchasing an 8x4 SpaceSaver Garden Shed. Please take the time to identify all the parts prior to assembly. Safety Points

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised February 4, 2016 the Millcreek-R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.

More information

Series 1500 Aluminum Door Canopy

Series 1500 Aluminum Door Canopy Series 500 Aluminum Door Canopy with Sidewings It is our recommendation that you read instructions carefully prior to assembly and installation. Series 500 with Sidewings mounting bar (A) top trim (B)

More information

Rockwell 4-in-1 Sliding Door

Rockwell 4-in-1 Sliding Door Rockwell 4-in-1 Sliding Door ASSEMBLY INSTRUCTIONS ROCKWELL 4-IN-1 SLIDING DOOR Recommended Tools Drill with Phillips Bit Socket Wrench with 7/16 Socket Rubber Mallet Adjustable Square ROCKWELL 4-IN-1

More information

Double Beam Freestanding Pergola Installation Guide

Double Beam Freestanding Pergola Installation Guide Double Beam Freestanding Pergola Installation Guide Patent Pending. Copyright 2011 USAVinyl, LLC - All Rights Reserved The information contained in these instructions are proprietary to USAVinyl, LLC and

More information

the Greenbriar 12' x 20' Best Barns USA Assembly Book Revised April

the Greenbriar 12' x 20' Best Barns USA Assembly Book Revised April Best Barns USA Assembly Book Revised April 28 2015 the Greenbriar 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.

More information

Oxford Stalls Installation Instructions

Oxford Stalls Installation Instructions Oxford Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 8/15/17 Before You Start Typical stall sizes are 10 x 10, 12 x 12 or

More information

Qwik-Fence Installation Instructions

Qwik-Fence Installation Instructions Qwik-Fence Installation Instructions 1 Tools Required The following installation instructions should be used as a guide for installing Folding Guard Qwik-Fence Partitions. Good common sense and appropriate

More information

12x12 Pavilion. Assembly Manual

12x12 Pavilion. Assembly Manual 12x12 Pavilion Assembly Manual 12x12 Pavilion Assembly Manual Congratulations on purchasing your new Pavilion. Thank You for your purchase and Welcome to the YardCraft Famiy. This manual is designed to

More information

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD

INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION

More information

Best Barns USA Assembly Book Revised November 3, 2016

Best Barns USA Assembly Book Revised November 3, 2016 Best Barns USA Assembly Book Revised November 3, 2016 the Aspen II 12' x 8' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive, Greenville, PA 16125 This manual is copyrighted. Under the

More information

Best Barns USA. Assembly Book. 12'x 16' the Millcreek. Revised September 19, 2017

Best Barns USA. Assembly Book. 12'x 16' the Millcreek. Revised September 19, 2017 Assembly Book Best Barns USA Revised September 19, 2017 the Millcreek 12'x 16' Manufactured by Reynolds Building Systems, Inc 205 Arlington Drive Greenville, PA 16125 This manual is copyrighted Under the

More information

Grand Garden Chalet 6X3 Assembly Manual - Costco

Grand Garden Chalet 6X3 Assembly Manual - Costco Revision #16 March 22nd, 2013 Grand Garden Chalet 6X3 Assembly Manual - Costco Thank you for purchasing a Grand Garden Chalet. Please take the time to identify all the parts prior to assembly. Please use

More information

Assembly Instructions 10 X 10 Aluminum Frame Building

Assembly Instructions 10 X 10 Aluminum Frame Building Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised February 4, 2016 the Millcreek-R 12'x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.

More information

10, 12 &14 Oval Gazebo Floor

10, 12 &14 Oval Gazebo Floor 0, 12 &14 Oval Gazebo Floor Revision: 2-26-03 Run: - BEFORE YOU BEGIN - Always wear OSHA-APPROVED safety glasses throughout assembly process First... Read these instructions thoroughly before you begin

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS A CSW Industrials Company PJC Floor Pan Expansion Joint Covers The following instructions are very important. Read them carefully, and be sure you understand them completely before

More information

Cape Cod Manual. Little Cottage Co. PO Box 455 Berlin, OH Little Cottage Co.

Cape Cod Manual. Little Cottage Co. PO Box 455 Berlin, OH Little Cottage Co. Tools Needed: -Cordless Drill (12v or higher) -#2 Square drive bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife with blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin,

More information

Installation Manual For ToddPod Outdoor Shower Enclosures

Installation Manual For ToddPod Outdoor Shower Enclosures Installation Manual For ToddPod Outdoor Shower Enclosures Contact us at 888-545-9763 or email us at office@toddpod.com with any questions during the installation process. Our service team is available

More information

6X3 Patio Garden Shed Assembly Manual

6X3 Patio Garden Shed Assembly Manual Thank you for purchasing a 6x3 Patio Garden Shed. Please take the time to identify all the parts prior to assembly. Revision #4 July 6th, 2016 6X3 Patio Garden Shed Assembly Manual Please use Safety Eyewear

More information

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A

1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A 1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com

More information

Installation Instructions - Model V4JSD 1

Installation Instructions - Model V4JSD 1 Installation Instructions - Model V4JSD 1 Support Assemblies: Parts list: (Note see enclosed cut sheet for quantities and dimensional information) A vertical structural member (1 ½ x 1 ½ modular frame)

More information

Contour Hanger ASSEMBLY INSTRUCTIONS

Contour Hanger ASSEMBLY INSTRUCTIONS Contour Hanger ASSEMBLY INSTRUCTIONS CONTOUR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket

More information

Industrial Hanger ASSEMBLY INSTRUCTIONS

Industrial Hanger ASSEMBLY INSTRUCTIONS Industrial Hanger ASSEMBLY INSTRUCTIONS INDUSTRIAL HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench

More information

Frameless Inline Door QCI5248

Frameless Inline Door QCI5248 INSTALLATION INSTRUCTIONS Frameless Inline Door QCI5248 FRAMELESS PANEL / DOOR / PANEL QCI5248 REV. 0 Page 1 Certified 06/16/2016 Parts List with glass to glass hinges *Quantities may vary. **Support Bar

More information

Assembly Book. 10' x 12' the Cambridge II. revised June 13, 2014

Assembly Book. 10' x 12' the Cambridge II. revised June 13, 2014 Assembly Book revised June 13, 2014 the Cambridge II 10' x 12' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted. Under the

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS STRIP DOORS AIR DOORS INSTALLATION INSTRUCTIONS BULK PVC FILM STRIP SHEET PANEL SCREENS, CURTAINS and ENCLOSURES MEGA-PRO SWINGING DOORS DOCK ACCESSORIES IMPORTANT Carefully examine the carton(s) for damage.

More information

Chapter 9. Windows and Exterior Doors

Chapter 9. Windows and Exterior Doors Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail apron

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised December 6, 2013 the Denver-R 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.

More information

x2 1/4 (6mm) Floor Anchor

x2 1/4 (6mm) Floor Anchor INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm

More information

6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015

6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015 6x6 Maximizer Storage Shed Assembly Manual Version #9 Feb 26th, 2015 Thank you for purchasing a 6x6 Maximizer Storage Shed. Please take the time to identify all the parts prior to assembly. Please Note-

More information

Screen Kit For Octagon Gazebo Assembly Manual

Screen Kit For Octagon Gazebo Assembly Manual Screen Kit For Octagon Gazebo Assembly Manual Revision #11 Feb 23rd/2015 Thank you for purchasing a Screen Kit for our Octagon Gazebo. Please take the time to identify all the parts prior to assembly.

More information

Assembly Book. 10' x 16' the Cambridge II. revised July 15, 2014

Assembly Book. 10' x 16' the Cambridge II. revised July 15, 2014 Assembly Book revised July 15, 2014 the Cambridge II 10' x 16' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted. Under the

More information

PAK Drum Roll Top Assembly Instructions. Note: 2 people will be required to assemble roll top

PAK Drum Roll Top Assembly Instructions. Note: 2 people will be required to assemble roll top PAK901 4 Drum Roll Top Assembly Instructions Note: 2 people will be required to assemble roll top PLEASE READ ASSEMBLY INSTRUCTIONS CARFULLY Tools required: 5/8 Socket & Ratchet 9/16 Deep Well Socket &

More information

Classic Saltbox Manual

Classic Saltbox Manual Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Utility knife w/ blade & hook blade -Speed Square -5/16 Wood Drill bit Little Cottage Co. PO Box

More information

Stag Hanger ASSEMBLY INSTRUCTIONS

Stag Hanger ASSEMBLY INSTRUCTIONS Stag Hanger ASSEMBLY INSTRUCTIONS STAG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench

More information

Chapter 9. Windows and Exterior Doors

Chapter 9. Windows and Exterior Doors Chapter 9. Windows and Exterior Doors 9.1 INSTALLING WINDOWS 9.2 INSTALLING EXTERIOR HOUSE DOORS 9.3 INSTALLING SHED DOOR 9.4 INSTALLING BASEMENT EGRESS COMPONENTS Tools needed by volunteers: Hammer Nail

More information

Assembly Instructions

Assembly Instructions Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt

More information

Frameless Bypass Slider

Frameless Bypass Slider INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need

More information

TWIG Hanger ASSEMBLY INSTRUCTIONS

TWIG Hanger ASSEMBLY INSTRUCTIONS TWIG Hanger ASSEMBLY INSTRUCTIONS TWIG HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket Wrench

More information

ASSEMBLY INSTRUCTIONS FOR STORETTE STA42

ASSEMBLY INSTRUCTIONS FOR STORETTE STA42 ASSEMBLY INSTRUCTIONS FOR STORETTE STA42 A01 CAUTION: Some parts have sharp edges. Care must be taken when handling the various pieces to avoid a mishap. For safety sake, please read the safety information

More information

Frameless Inline Door With Return QCI5263

Frameless Inline Door With Return QCI5263 INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges

More information

Frameless Bypass Slider

Frameless Bypass Slider INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 3/8 or 1/4 Glass Bypass Slider with Exposed Rollers QCI5301 Rev 1 Page 1 Certified 6/5/2017 Tools: To install your New Shower Enclosure, you may

More information

Frameless Fixed Panel Slider

Frameless Fixed Panel Slider INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need

More information

Wooden Rectangle Pergola Assembly Manual

Wooden Rectangle Pergola Assembly Manual Wooden Rectangle Pergola Assembly Manual Pergola Assembly Manual Thank you for your purchase of this Pergola This manual is designed to simplify the assembly process, however we recommend having an experienced

More information

8x12 SpaceMaker Garden Shed Assembly Manual Revision #20 June 27th, 2017

8x12 SpaceMaker Garden Shed Assembly Manual Revision #20 June 27th, 2017 8x12 SpaceMaker Garden Shed Assembly Manual Revision #20 June 27th, 2017 Thank you for purchasing our 8x12 SpaceMaker Garden Shed. Please take the time to identify all the parts prior to assembly. Safety

More information

8x4 SpaceSaver Garden Shed Bevel Model Assembly Manual Revision #18 March 9th, 2017

8x4 SpaceSaver Garden Shed Bevel Model Assembly Manual Revision #18 March 9th, 2017 8x4 SpaceSaver Garden Shed Bevel Model Assembly Manual Revision #18 March 9th, 2017 Thank you for purchasing an 8x4 SpaceSaver Garden Shed. Please take the time to identify all the parts prior to assembly.

More information

Install Instructions. NewAge Steel Welded Tall Locker

Install Instructions. NewAge Steel Welded Tall Locker Kit Contains Full Width Adjustable Steel Shelves (4) Height-Adjustable Steel Leveling Legs (4) Aluminum Door Trim (2) 2.5 x ¼ Cabinet Mounting Lag Bolts (4) Large Zinc Plated Mounting Washers (4) 5/8 x

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised September 19, 2016 the Meadowbrook-R 16' x 10' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is

More information

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE

INSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT

More information

INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS

INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS INSTALLATION INSTRUCTIONS FOR PLASCORE NARROW STILE DOORS The following information is provided by Plascore, Inc., as a general guideline for the installation of the Plascore Narrow Stile Door and Jamb

More information

Pillar Hanger ASSEMBLY INSTRUCTIONS

Pillar Hanger ASSEMBLY INSTRUCTIONS Pillar Hanger ASSEMBLY INSTRUCTIONS PILLAR HANGER Recommended Tools Drill with 1/8, 1/4, and 3/8 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket

More information

the Greenbriar 12' x 20' Best Barns USA Assembly Book Revised May 31, 2013

the Greenbriar 12' x 20' Best Barns USA Assembly Book Revised May 31, 2013 Best Barns USA Assembly Book Revised May 31, 2013 the Greenbriar 12' x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised July 6, 2015 Garage Door by Owner Tahoe-R 12'x 20' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual

More information

Star Barn Manual. Tools Needed:

Star Barn Manual. Tools Needed: Tools Needed: -Cordless Drill (12V or higher) -#2 Square Drive Bit -Hammer -6 Step Ladder -Tape Measure -Square utility knife w/ blade & hook blade -Speed Square Little Cottage Co. PO Box 455 Berlin, OH

More information

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283

FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 FIXED SHOWER SCREEN For Wall Mount Hinges QCI5283 QCI5283 Page 1 Date Certified: 06/16/2016 Parts List with wall mount clamp ITEM NO. DESCRIPTION QTY. 1 FIXED GLASS PANEL 1 2 WALL MOUNT CLAMP 1 3 U-CHANNEL

More information

ROCKWELL 4-IN-1 DOOR. Two Panel Door. Half X Door. Z Combination Door. Double X Door

ROCKWELL 4-IN-1 DOOR. Two Panel Door. Half X Door. Z Combination Door. Double X Door ROCKWE 4-IN-1 DOOR Two Panel Door Half X Door Double X Door Z Combination Door Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials

More information

Best Barns USA Assembly Book

Best Barns USA Assembly Book Best Barns USA Assembly Book Revised February 17, 2015 the Meadowbrook-R 12' x 10' Manufactured by Reynolds Building Systems, Inc. 205 Arlington Drive Greenville, PA 16125 724-646-3775 This manual is copyrighted.

More information

Boxed Shed. QUAKER or A-FRAME SIZES: 6 x 8 6 x 10 T1-11Siding

Boxed Shed. QUAKER or A-FRAME SIZES: 6 x 8 6 x 10 T1-11Siding Boxed Shed QUAKER or A-FRAME SIZES: 6 x 8 6 x 10 T1-11Siding Required Equipment; * Power Drill with square head bit * Hammer, Square, Gloves & an Allen wrench * Step Ladder Screws Supplied; * 2 for roof

More information

Deck Mount Installation with Bench

Deck Mount Installation with Bench Deck Mount Installation with Bench 1. Mark track with square. 2. Cut tracks with saw. 3. Drill ¼ hole (if needed.) 4. Countersink track. 5. Countersink all track 6. File all track ends. ends. 7. Lay out

More information