Absco Space Saver Shed Assembly Instructions Model: 23081SK

Size: px

Start display at page:

Download "Absco Space Saver Shed Assembly Instructions Model: 23081SK"

Rudolph Boyd
5 years ago
Views:

Assembly Instructons Model: 2308SK FRONT BASE LENGTH: 2.26m SIDE BASE LENGTH: 0.78m FRONT WALL HEIGHT:.

95m CONCRETE SLAB 880mm 2360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm.

Australan made shed. For further assstance please vst our detaled nstructonal vdeo lbrary at Http://www.abscosheds.

1 Assembly Instructons Model: 2308SK FRONT BASE LENGTH: 2.26m SIDE BASE LENGTH: 0.78m FRONT WALL HEIGHT:.80m REAR WALL HEIGHT:.95m CONCRETE SLAB 880mm 2360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm EDGES DOWNWARDS BY 0mm. 50mm 0mm 50mm THIS WILL ENSURE THAT WATER RUN OFF IS KEPT CLEAR FROM YOUR SHED We thank you for choosng an Australan made shed. For further assstance please vst our detaled nstructonal vdeo lbrary at At ABSCO Industres we are always lookng to be number ONE, so please let us know what you thnk of our nstructons. Feedback makes us better. ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE

Model: 2308SK GENERAL INSTRUCTIONS Before commencng any

thorough understandng of assembly methods and assocated

Unpack the carton and carefully dentfy and check off all

An uneven surface may result n msalgnment of parts.

slab and anchored down approprately (refer to last page

Anchor sets are not suppled as standard tems wth ths

Masonry: 0mm Some parts may have sharp edges.

2 Model: 2308SK GENERAL INSTRUCTIONS Before commencng any assembly, read through these nstructons n detal to gan a thorough understandng of assembly methods and assocated detals. Unpack the carton and carefully dentfy and check off all the parts aganst the parts descrbed and llustrated on pages three and four. SITE PREPARATION The ste for the shed must be level. An uneven surface may result n msalgnment of parts. It s recommended that the shed be set on a 00mm concrete slab and anchored down approprately (refer to last page for detals). Anchor sets are not suppled as standard tems wth ths product as some customers wsh to use ther own anchorng systems. TOOLS REQUIRED OPTIONAL A NOTE ON SAFETY Normal: 4mm & 0mm Masonry: 0mm Some parts may have sharp edges. It s advsable to wear gloves when handlng these tems and safety glasses f drllng holes. Sensble shoes are hghly recommended. Do not erect your shed n wndy condtons, ensure that the shed s securely anchored to a sold foundaton mmedately after constructon s completed. It s hghly recommended to erect the shed wth two or more people. ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 2

3 Model: 2308SK COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 2 STEEL SHEET 95 X 773mm 43B 2 L = 773mm 8J STEEL SHEET 95 X 773mm 43C L = 788mm 79B STEEL SHEET 95mm X 773mm X4L WITH HINGES L = 725mm 58A STEEL SHEET 95mm X 773mm X4R L = 725mm 58B 3 STEEL SHEET 865mm X 773mm 43D 2 L = 773mm 58C 2 STEEL SHEET 785mm X 73mm 32A JAMB L= 785mm 89A STEEL SHEET 725mm X 773mm B JAMB L= 785mm 89B 2 L = 786mm 6B JAMB L= 788mm 90B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 3

4 Model: 2308SK COMPONENTS PACKING LIST - CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 6 JOINER L= 200mm CSJ THESE COMPONENTS ARE TO BE JOINED TO THESE COMPONENTS L = 26.5mm 54AL L = 26.5mm 54AR L = 26.5mm 54CL L = 26.5mm 54CR L = 26.5mm 54BL L = 26.5mm 54BR 2 L = 26.5mm 8CL 2 L = 26.5mm 8CR L = 26.5mm 8DL L = 26.5mm 8DR ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 4

5 Model: 2308SK COMPONENTS PACKING LIST - (CONT.) CHECK OFF ALL COMPONENTS QTY COMPONENT DESCRIPTION PART No. CHECK QTY COMPONENT DESCRIPTION PART No. CHECK 2 9A 2 JAMB L= 20mm LIP TRIM L= 865mm CONTENTS OF FITTINGS PACKET 88B 220 SELF TAPPING SCREWS DOOR PADBOLT 22A 6 4mm CSK SCREW & NUT SECURE HINGES TO DOOR DOOR PADBOLT HASP ASSEMBLY INSTRUCTIONS 6 3mm POP RIVETS SECURE HINGES TO DOOR (ALTERNATIVE FIXING METHOD) DOOR STRAP L: 65mm 2A ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 5

Model: 2308SK INSTRUCTIONS FOR JOINING SPLICED S NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> <<JOIN JOIN>> = = J JOIN>> SJ STEP.

Jon the frst channel to the CSJ by nsertng the center of the CSJ (on an angle) to the end of the channel where the JOIN>> text s marked. Push down one sde of the CSJ untl you hear a 'clck'.

(THESE SCREWS MAY HAVE TO BE TEMPORARILY REMOVED AND REPLACED DURING LATER ASSEMBLY) = = STEP 3.

6 Model: 2308SK INSTRUCTIONS FOR JOINING SPLICED S NOTE: THE TEXT MARKED ON ALL PARTS MUST BE SHOWN ON THE SAME SIDE AS EACH OTHER. = = = = CSJ JOIN>> <<JOIN JOIN>> = = J JOIN>> SJ STEP. Poston the channels and the CSJ joner channel so the center of the CSJ s n lne wth the end of each channel to be joned together. STEP 2. Jon the frst channel to the CSJ by nsertng the center of the CSJ (on an angle) to the end of the channel where the JOIN>> text s marked. Push down one sde of the CSJ untl you hear a 'clck'. = = JOIN>> <<JOIN JOIN>> <<JOIN DRILL 4 x 3mm (2 PER A SIDE) HOLES TO SECURE SECTIONS TOGETHER. (THESE SCREWS MAY HAVE TO BE TEMPORARILY REMOVED AND REPLACED DURING LATER ASSEMBLY) = = STEP 3. Jon the second channel to the CSJ by postonng the <<JOIN end of the channel at the center of the CSJ (on an angle). Push the CSJ nto the channel untl you here a 'clck'. FINISHED The joned channels should now look lke the pcture above wth the CSJ postoned equally nsde of the joned channels. PUSH QTY = 6 pcs. CSJ PUSH CSJ CSJ CSJ HIGH-SIDE = = CSJ = = LOW-SIDE 20mm 5mm CSJ ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 6

7 Model: 2308SK STEP. PRE-ASSEMBLY OF SPLICED S NOTE: JOIN TOGETHER 2 X SECTIONS USING 6 X JOINERS (PART CSJ) 2 X 8CR 2 X 8CL X 54AR X 54AL X 54CR X 54CL NOTE: SOME S HAVE HOLES IN THEM - YOU WILL NEED TO RE-DRILL HOLES ON ANY WHERE THE CSJ JOINING COVERS HOLES ON THE S YOU ARE CONNECTING 2253mm 8CR 8CL 54CR 54CL 54AR 54AL 8DL 54BR 54BL = = = = = 2 x 8C x 54A x 54C x 54B x 8D X 54BR X 54BL 8DR X 8DR X 8DL ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 7

8 Model: 2308SK VIEW OF ROOF COMPONENTS 8C 43D 43D 43D 8C 88B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 88B PAGE 8 NO.

9 Model: 2308SK 54B 43B X4L 43C 90B 6B 43B 32A X4R 32A 89A 9A 8D 89B 79B 8J 54C VIEW OF WALL COMPONENTS ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 22A 6B 54A 8J B PAGE 9

Model: 2308SK ABSCO ASSEMBLY INTRODUCTION The snaptte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners.

end. Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS D PUSH HIGH SIDE Jon components together by pre-drllng the holes frst.

10 Model: 2308SK ABSCO ASSEMBLY INTRODUCTION The snaptte assembly system locks most permeter channels to all roof and wall sheets wthout the need for tools and fasteners. To pre-assemble the four wall panels and two roof panels, the permeter channels are secured to the top and bottom of each panel usng the snaptte system, as detaled on the followng pages wherever you see the symbol. HIGH SIDE PUSH HIGH SIDE HIGH SIDE HIGH SIDE PUSH After jonng sheets together, poston channel over one end of the sheets, gently tappng t over the snaptte lugs, workng along the sheets to the other end. Poston sheets on tmbers, trestles or partly over edge of concrete slab. FASTENING SYMBOLS D PUSH HIGH SIDE Jon components together by pre-drllng the holes frst. Use one component as a template to mark where the holes are. Drll wth 3mm drll bt. Jon components together wth one screw at ths locaton only, as some channel sectons have extra holes that are not requred for ths model of garden shed Do not jon components together at ths locaton yet, as the screw may obstruct further assembly of other components ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 Each permeter channel must fnsh flush wth the edges of the sheets.the snaptte system allows adjustment for ths process by smply tappng the channel along the sheets untl each end s neatly flush. If you need to remove channels from the panels, pull the channel along the panel from opposng ends. You may need someone to help wth ths. 3mm POP RIVETS 4mm NUT & BOLT SET PAGE 0

11 Model: 2308SK DOOR 6. DOOR PANEL ASSEMBLY 58C 58A 58B B 2A 58C ALL VERTICAL DOOR S ARE INSTALLED IN THE REVERSE DIRECTION IN COMPARISON TO HORIZONTAL DOOR S 20mm FLANGE B 5mm FLANGE ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE

12 Model: 2308SK REAR PANEL ASSEMBLY 43B 43C 43B 54B 8D ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 2

13 Model: 2308SK SIDE PANEL ASSEMBLY (TWO REQUIRED) 6B X4R X4L 8J ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 3

14 Model: 2308SK ROOF PANEL ASSEMBLY 43D 43D 43D 8C 88B 8C 88B ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 4

15 Model: 2308SK FRONT PANEL ASSEMBLY 89A 89B 32A 32A 54A 90B SNAP T TE 79B 54C ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 5

16 Model: 2308SK 9A B 9A B NOTE: NUTS AND BOLTS (SUPPLIED) MAY BE USED INSTEAD OF POP RIVETS (SUPPLIED) BY SIMPLY ENLARGING THE HINGE HOLE SETS IN THE JAMB USING A 4MM DRILL BIT NOTE: The two holes requred to connect the padbolt hasp for each door have not been pre-punched, to allow for proper algnment. poston each hasp centrally over the padbolt shaft, and drll 3mm holes and secure wth screws ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 6

17 Model: 2308SK PANEL CONSTRUCTION NOTE: Take care to ensure that both front and rear wall panels are not postoned upsde down. The top channel of each panel s pre-punched for attachng roof sheet. The base channels are not pre-punched. SIDE WALL PANEL S FIT INTO THE NOTCHED FRONT AND REAR WALL PANEL S ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 7

18 Model: 2308SK FINAL CONSTRUCTION ANCHORING OF SHED LOCATION OF 8 CONCRETE ANCHORS - EACH ANCHOR CONSISTS OF ONE NUT, BOLT, DYNABOLT AND STEEL ANGLE - DRILL A 0mm HOLE INTO THE WALL SHEET BOLT & NUT STEEL ANGLE WALL SHEET SLAB - DRILL A 0mm HOLE INTO THE CONCRETE DYNABOLT ABSCO INDUSTRIES ASSEMBLY INSTRUCTION - MODEL: 2308SK 5/04/6 PAGE 8

Absco Space Saver Shed Assembly Instructions Model: J30082S

Absco Space Saver Shed Assembly Instructions Model: J30082S Assembly Instructons FRONT BASE LENGTH: 9ft-0-7 64n SIDE BASE LENGTH: ft-6-45 64n FRONT WALL HEIGHT: 5ft-0-55 64n REAR WALL HEIGHT: 6ft-4-49 64n ft-0-4 64n CONCRETE SLAB 0ft--3 64n CONCRETE SLAB WHEN LAYING