PHOENIX. Physics with Homemade Equipment and Innovative Experiments

Physics with Home-made Equipment and Innovative Experiments. Ajith Kumar B.P., Inter University Accelerator Centre, New Delhi

Physics with Home-made Equipment and Innovative Experiments Ajith Kumar B.P., Inter University Accelerator Centre, New Delhi 110 067 1 Introduction Progress in science is achieved through advances in both

ENGR4300 Test 3A Fall 2002

1. 555 Timer (20 points) Figure 1: 555 Timer Circuit For the 555 timer circuit in Figure 1, find the following values for R1 = 1K, R2 = 2K, C1 = 0.1uF. Show all work. a) (4 points) T1: b) (4 points) T2:

OpenAFM. Electronics

OpenAFM Electronics Voice Coils Each coil is controlled by a pair of push-pull amplifiers. One of each pair has a constant output voltage of 2.5v The other member of the pair is controlled by the output

An induced emf is the negative of a changing magnetic field. Similarly, a self-induced emf would be found by

This is a study guide for Exam 4. You are expected to understand and be able to answer mathematical questions on the following topics. Chapter 32 Self-Induction and Induction While a battery creates an

BASIC ELECTRICITY/ APPLIED ELECTRICITY

BASIC ELECTRICITY/ APPLIED ELECTRICITY PREAMBLE This examination syllabus has been evolved from the Senior Secondary School Electricity curriculum. It is designed to test candidates knowledge and understanding

BASIC ELECTRICITY/ APPLIED ELECTRICITY

BASIC ELECTRICITY/ APPLIED ELECTRICITY PREAMBLE This examination syllabus has been evolved from the Senior Secondary School Electricity curriculum. It is designed to test candidates knowledge and understanding

GENERATION OF SIGNALS USING LABVIEW FOR MAGNETIC COILS WITH POWER AMPLIFIERS

GENERATION OF SIGNALS USING LABVIEW FOR MAGNETIC COILS WITH POWER AMPLIFIERS Ashmi G V 1, Meena M S 2 1 ER&DCI-IT, Centre for Development of Advanced Computing, Thiruvananthapuram(India) 2 LAMP Group,

Number of Lessons:155 #14B (P) Electronics Technology with Digital and Microprocessor Laboratory Completion Time: 42 months

PROGRESS RECORD Study your lessons in the order listed below. Number of Lessons:155 #14B (P) Electronics Technology with Digital and Microprocessor Laboratory Completion Time: 42 months 1 2330A Current

BINARY AMPLITUDE SHIFT KEYING

BINARY AMPLITUDE SHIFT KEYING AIM: To set up a circuit to generate Binary Amplitude Shift keying and to plot the output waveforms. COMPONENTS AND EQUIPMENTS REQUIRED: IC CD4016, IC 7474, Resistors, Zener

GATE: Electronics MCQs (Practice Test 1 of 13)

GATE: Electronics MCQs (Practice Test 1 of 13) 1. Removing bypass capacitor across the emitter leg resistor in a CE amplifier causes a. increase in current gain b. decrease in current gain c. increase

Introduction to Electronic Circuit for Instrumentation

Introduction to Electronic Circuit for Instrumentation Fundamental quantities Length Mass Time Charge and electric current Heat and temperature Light and luminous intensity Matter (atom, ion and molecule)

Data Conversion and Lab Lab 4 Fall Digital to Analog Conversions

Digital to Analog Conversions Objective o o o o o To construct and operate a binary-weighted DAC To construct and operate a Digital to Analog Converters Testing the ADC and DAC With DC Input Testing the

Chapter 8. Chapter 9. Chapter 6. Chapter 10. Chapter 11. Chapter 7

5.5 Series and Parallel Combinations of 246 Complex Impedances 5.6 Steady-State AC Node-Voltage 247 Analysis 5.7 AC Power Calculations 256 5.8 Using Power Triangles 258 5.9 Power-Factor Correction 261

Direct Current Waveforms

Cornerstone Electronics Technology and Robotics I Week 20 DC and AC Administration: o Prayer o Turn in quiz Direct Current (dc): o Direct current moves in only one direction in a circuit. o Though dc must

ASTABLE MULTIVIBRATOR

555 TIMER ASTABLE MULTIIBRATOR MONOSTABLE MULTIIBRATOR 555 TIMER PHYSICS (LAB MANUAL) PHYSICS (LAB MANUAL) 555 TIMER Introduction The 555 timer is an integrated circuit (chip) implementing a variety of

Project: Electromagnetic Ring Launcher

Project: Electromagnetic Ring Launcher Introduction: In science museums and physics-classrooms an experiment is very commonly demonstrated called the Jumping Ring or Electromagnetic Ring Launcher. The

CHAPTER IV DESIGN AND ANALYSIS OF VARIOUS PWM TECHNIQUES FOR BUCK BOOST CONVERTER

59 CHAPTER IV DESIGN AND ANALYSIS OF VARIOUS PWM TECHNIQUES FOR BUCK BOOST CONVERTER 4.1 Conventional Method A buck-boost converter circuit is a combination of the buck converter topology and a boost converter

Laboratory Exercise 6 THE OSCILLOSCOPE

Introduction Laboratory Exercise 6 THE OSCILLOSCOPE The aim of this exercise is to introduce you to the oscilloscope (often just called a scope), the most versatile and ubiquitous laboratory measuring

High Current Amplifier

High Current Amplifier - Introduction High Current Amplifier High current amplifier is often a very useful piece of instrument to have in the lab. It is very handy for increasing the current driving capability

Veer Narmad South Gujarat University, Surat

Unit I: Passive circuit elements (With effect from June 2017) Syllabus for: F Y B Sc (Electronics) Semester- 1 PAPER I: Basic Electrical Circuits Resistors, resistor types, power ratings, resistor colour

Introduction to OrCAD. Simulation Program With Integrated Circuits Emphasis.

Islamic University of Gaza Faculty of Engineering Electrical Engineering department Digital Electronics Lab (EELE 3121) Eng. Mohammed S. Jouda Eng. Amani S. abu reyala Experiment 1 Introduction to OrCAD

DEFINITION: Classification of oscillators Based on the frequency generated Oscillator type Frequency range

DEFINITION: An oscillator is just an electronic circuit which converts dc energy into AC energy of required frequency. (Or) An oscillator is an electronic circuit which produces an ac output without any

#8A RLC Circuits: Free Oscillations

#8A RL ircuits: Free Oscillations Goals In this lab we investigate the properties of a series RL circuit. Such circuits are interesting, not only for there widespread application in electrical devices,

Last Time. P and N type semiconductors Diode internals Transistors NPN PNP

Last Time P and N type semiconductors Diode internals Transistors NPN PNP Device of the Day... Piezo microphone Device of the Day... Transistor Recap Transistors operate as current amplifiers With the

Devices and Op-Amps p. 1 Introduction to Diodes p. 3 Introduction to Diodes p. 4 Inside the Diode p. 6 Three Diode Models p. 10 Computer Circuit

Contents p. v Preface p. ix Devices and Op-Amps p. 1 Introduction to Diodes p. 3 Introduction to Diodes p. 4 Inside the Diode p. 6 Three Diode Models p. 10 Computer Circuit Analysis p. 16 MultiSIM Lab

Group 1616B: Wireless Power Transfer. Brandon Conlon Juan Carlos Lluberes Tyler Hayslett Advisors: Peng Zhang & Taofeek Orekan

Group 1616B: Wireless Power Transfer Brandon Conlon Juan Carlos Lluberes Tyler Hayslett Advisors: Peng Zhang & Taofeek Orekan System Overview Frequency adjustable subsea Resonant Wireless Power transfer

Experiment 1: Instrument Familiarization (8/28/06)

Electrical Measurement Issues Experiment 1: Instrument Familiarization (8/28/06) Electrical measurements are only as meaningful as the quality of the measurement techniques and the instrumentation applied

Experiment 1: Instrument Familiarization

Electrical Measurement Issues Experiment 1: Instrument Familiarization Electrical measurements are only as meaningful as the quality of the measurement techniques and the instrumentation applied to the

Generators and Alternating Current

Generators and Alternating Current If one end of a magnet is moved in and out of a coil of wire, the induced voltage alternates in direction. The greater the frequency with which the magnet moves in and

1 2 B.E./B.Tech. DEGREE EXAMINATION, NOVEMBER/DECEMBER 2010 Fourth Semester Electrical and Electronics Engineering EE 2254 LINEAR INTEGRATED CIRCUITS AND APPLICATIONS (Common to Instrumentation and Control

SERVO MOTOR CONTROL TRAINER

SERVO MOTOR CONTROL TRAINER UC-1780A FEATURES Open & closed loop speed and position control. Analog and digital control techniques. PC based instrumentation include oscilloscope, multimeter and etc. PC

Capacitive Touch Sensing Tone Generator. Corey Cleveland and Eric Ponce

Capacitive Touch Sensing Tone Generator Corey Cleveland and Eric Ponce Table of Contents Introduction Capacitive Sensing Overview Reference Oscillator Capacitive Grid Phase Detector Signal Transformer

Associate In Applied Science In Electronics Engineering Technology Expiration Date:

PROGRESS RECORD Study your lessons in the order listed below. Associate In Applied Science In Electronics Engineering Technology Expiration Date: 1 2330A Current and Voltage 2 2330B Controlling Current

Careers in Electronics Using a Calculator Safety Precautions Dc Circuits p. 1 Fundamentals of Electricity p. 3 Matter, Elements, and Compounds p.

Preface p. vii Careers in Electronics p. xii Using a Calculator p. xvi Safety Precautions p. xix Dc Circuits p. 1 Fundamentals of Electricity p. 3 Matter, Elements, and Compounds p. 4 A Closer Look at

Emitter base bias. Collector base bias Active Forward Reverse Saturation forward Forward Cut off Reverse Reverse Inverse Reverse Forward

SEMICONDUCTOR PHYSICS-2 [Transistor, constructional characteristics, biasing of transistors, transistor configuration, transistor as an amplifier, transistor as a switch, transistor as an oscillator] Transistor

M.D. Singh J.G. Joshi MECHATRONICS

M.D. Singh J.G. Joshi MECHATRONICS MECHATRONICS MECHATRONICS M.D. SINGH Formerly Principal Sagar Institute of Technology and Research Bhopal J.G. JOSHI Lecturer Department of Electronics and Telecommunication

Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET REV. NO. : REV.

Dev Bhoomi Institute Of Technology Department of Electronics and Communication Engineering PRACTICAL INSTRUCTION SHEET LABORATORY MANUAL EXPERIMENT NO. ISSUE NO. : ISSUE DATE: July 200 REV. NO. : REV.

IT.MLD900 SENSORS AND TRANSDUCERS TRAINER. Signal Conditioning

SENSORS AND TRANSDUCERS TRAINER IT.MLD900 The s and Instrumentation Trainer introduces students to input sensors, output actuators, signal conditioning circuits, and display devices through a wide range

Experiment 9: AC circuits

Experiment 9: AC circuits Nate Saffold nas2173@columbia.edu Office Hour: Mondays, 5:30PM-6:30PM @ Pupin 1216 INTRO TO EXPERIMENTAL PHYS-LAB 1493/1494/2699 Introduction Last week (RC circuit): This week:

(i) Determine the admittance parameters of the network of Fig 1 (f) and draw its - equivalent circuit.

I.E.S-(Conv.)-1995 ELECTRONICS AND TELECOMMUNICATION ENGINEERING PAPER - I Some useful data: Electron charge: 1.6 10 19 Coulomb Free space permeability: 4 10 7 H/m Free space permittivity: 8.85 pf/m Velocity

The Electro-Magnetic Spectrum

The Electro-Magnetic Spectrum Part Three In This Issue: All about Tubes How a diode rectifier works How a triode amplifier works How the mixer in your receiver works Dear Friends: For quite some time I

4.2.2 Metal Oxide Semiconductor Field Effect Transistor (MOSFET)

4.2.2 Metal Oxide Semiconductor Field Effect Transistor (MOSFET) The Metal Oxide Semitonductor Field Effect Transistor (MOSFET) has two modes of operation, the depletion mode, and the enhancement mode.

SUGAR CAPACITY EXPERIMENT

SUGAR CAPACITY EXPERIMENT A PRACTICAL INTRODUCTION TO AC THEORY P R E A M B L E Sugar Capacity is a PBL Experimental Group Research Project to be undertaken by small groups of (approximately 4) first year

Using Optical Isolation Amplifiers in Power Inverters for Voltage, Current and Temperature Sensing

Using Optical Isolation Amplifiers in Power Inverters for Voltage, Current and Temperature Sensing by Hong Lei Chen, Product Manager, Avago Technologies Abstract Many industrial equipments and home appliances

Experiment (1) Principles of Switching

Experiment (1) Principles of Switching Introduction When you use microcontrollers, sometimes you need to control devices that requires more electrical current than a microcontroller can supply; for this,

UNIVERSITI MALAYSIA PERLIS

UNIVERSITI MALAYSIA PERLIS ANALOG ELECTRONICS II EMT 212 2009/2010 EXPERIMENT # 3 OP-AMP (OSCILLATORS) 1 1. OBJECTIVE: 1.1 To demonstrate the Wien bridge oscillator 1.2 To demonstrate the RC phase-shift

ECE 303 ELECTRONICS LABORATORY SPRING No labs meet this week. Course introduction & lab safety

ECE 303 ELECTRONICS LABORATORY SPRING 2018 Week of Jan. 8 Jan. 15 Jan. 22 Jan. 29 Feb. 5 Feb. 12 Feb. 19 Feb. 26 Mar. 5 Mar. 12 Mar. 19 Mar. 26 Apr. 2 Apr. 9 Apr. 16 Topic No labs meet this week Course

Lesson Plan. Week Theory Practical Lecture Day. Topic (including assignment / test) Day. Thevenin s theorem, Norton s theorem

Name of the faculty: GYANENDRA KUMAR YADAV Discipline: APPLIED SCIENCE(C.S.E,E.E.ECE) Year : 1st Subject: FEEE Lesson Plan Lesson Plan Duration: 31 weeks (from July, 2018 to April, 2019) Week Theory Practical

LESSON PLAN. SUBJECT: LINEAR IC S AND APPLICATION NO OF HOURS: 52 FACULTY NAME: Mr. Lokesh.L, Hema. B DEPT: ECE. Portions to be covered

LESSON PLAN SUBJECT: LINEAR IC S AND APPLICATION SUB CODE: 15EC46 NO OF HOURS: 52 FACULTY NAME: Mr. Lokesh.L, Hema. B DEPT: ECE Class# Chapter title/reference literature Portions to be covered MODULE I

Constructing response curves: Introduction to the BODE-diagram

Topic Constructing response curves: Introduction to the BODE-diagram Author Jens Bribach, GFZ German Research Centre for Geosciences, Dept. 2: Physics of the Earth, Telegrafenberg, D-14473 Potsdam, Germany;

Calhoon MEBA Engineering School. Study Guide for Proficiency Testing Industrial Electronics

Calhoon MEBA Engineering School Study Guide for Proficiency Testing Industrial Electronics January 0. Which factors affect the end-to-end resistance of a metallic conductor?. A waveform shows three complete

INVESTIGATION AND DESIGN OF HIGH CURRENT SOURCES FOR B-H LOOP MEASUREMENTS

INVESTIGATION AND DESIGN OF HIGH CURRENT SOURCES FOR B-H LOOP MEASUREMENTS Boyanka Marinova Nikolova, Georgi Todorov Nikolov Faculty of Electronics and Technologies, Technical University of Sofia, Studenstki

LINEAR IC APPLICATIONS

1 B.Tech III Year I Semester (R09) Regular & Supplementary Examinations December/January 2013/14 1 (a) Why is R e in an emitter-coupled differential amplifier replaced by a constant current source? (b)

The Tuned Circuit. Aim of the experiment. Circuit. Equipment and components. Display of a decaying oscillation. Dependence of L, C and R.

The Tuned Circuit Aim of the experiment Display of a decaying oscillation. Dependence of L, C and R. Circuit Equipment and components 1 Rastered socket panel 1 Resistor R 1 = 10 Ω, 1 Resistor R 2 = 1 kω

Embedded systems. Exercise session 1. Introduction and project presentation

Embedded systems Exercise session 1 Introduction and project presentation Introduction Contact Mail : michael.fonder@ulg.ac.be Office : 1.82a, Montefiore Website for the exercise sessions and the project

Industry s First 0.8µV RMS Noise LDO Has 79dB Power Supply Rejection Ratio at 1MHz Amit Patel

April 15 Volume 25 Number 1 I N T H I S I S S U E patent-pending boost-buck ED driver topology 8 I 2 C programmable supervisors with EEPROM 12 Industry s First 0.8µV RMS Noise DO Has 79dB Power Supply

Draw in the space below a possible arrangement for the resistor and capacitor. encapsulated components

1). An encapsulated component is known to consist of a resistor and a capacitor. It has two input terminals and two output terminals. A 5V, 1kHz square wave signal is connected to the input terminals and

Effect of Aging on Power Integrity of Digital Integrated Circuits

Effect of Aging on Power Integrity of Digital Integrated Circuits A. Boyer, S. Ben Dhia Alexandre.boyer@laas.fr Sonia.bendhia@laas.fr 1 May 14 th, 2013 Introduction and context Long time operation Harsh

Magnetic Induction Kit

Magnetic Induction Kit Investigating Faraday=s laws of electromagnetic induction DO094 Revision History 1) 003 Original. ) 3.7.07 Corrected EMF definition. Added Appendix. Reformatted. Copyright 003-007

5. Transducers Definition and General Concept of Transducer Classification of Transducers

5.1. Definition and General Concept of Definition The transducer is a device which converts one form of energy into another form. Examples: Mechanical transducer and Electrical transducer Electrical A

GCSE Electronics. Scheme of Work

GCSE Electronics Scheme of Work Week Topic Detail Notes 1 Practical skills assemble a circuit using a diagram recognize a component from its physical appearance (This is a confidence building/motivating

Sensors and Actuators Introduction to sensors

Sensors and Actuators Introduction to sensors Sander Stuijk (s.stuijk@tue.nl) Department of Electrical Engineering Electronic Systems INDUCTIVE SENSORS (Chapter 3.4, 7.3) 3 Inductive sensors 4 Inductive

Expect to be successful, expect to be liked,

Thought of the Day Expect to be successful, expect to be liked, expect to be popular everywhere you go. Oscillators 1 Oscillators D.C. Kulshreshtha Oscillators 2 Need of an Oscillator An oscillator circuit

Physics 132 Quiz # 23

Name (please (please print) print) Physics 132 Quiz # 23 I. I. The The current in in an an ac ac circuit is is represented by by a phasor.the value of of the the current at at some time time t t is is

Chapter 16 PCB Layout and Stackup

Chapter 16 PCB Layout and Stackup Electromagnetic Compatibility Engineering by Henry W. Ott Foreword The PCB represents the physical implementation of the schematic. The proper design and layout of a printed

KNOWLEDGE INTEGRATION IN THE RED PROGRAM. Revolutionizing Engineering Departments

KNOWLEDGE INTEGRATION IN THE RED PROGRAM Revolutionizing Engineering Departments STEM EDUCATION NEEDS RADICAL, FUNDAMENTAL, AND STRUCTURAL CHANGES BEYOND THE EXISTING NORMS 42% of jobs will be in risk

Inductance. Chapter 30. PowerPoint Lectures for University Physics, Thirteenth Edition Hugh D. Young and Roger A. Freedman. Lectures by Wayne Anderson

Chapter 30 Inductance PowerPoint Lectures for University Physics, Thirteenth Edition Hugh D. Young and Roger A. Freedman Lectures by Wayne Anderson Goals for Chapter 30 To learn how current in one coil

Inductance. Chapter 30. PowerPoint Lectures for University Physics, Thirteenth Edition Hugh D. Young and Roger A. Freedman. Lectures by Wayne Anderson

Chapter 30 Inductance PowerPoint Lectures for University Physics, Thirteenth Edition Hugh D. Young and Roger A. Freedman Lectures by Wayne Anderson Goals for Chapter 30 To learn how current in one coil

UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering

UNIVERSITY OF NORTH CAROLINA AT CHARLOTTE Department of Electrical and Computer Engineering EXPERIMENT 7 BJT AMPLIFIER CONFIGURATIONS AND INPUT/OUTPUT IMPEDANCE OBJECTIVES The purpose of this experiment

ME 333 Assignment 7 and 8 PI Control of LED/Phototransistor Pair. Overview

ME 333 Assignment 7 and 8 PI Control of LED/Phototransistor Pair Overview For this assignment, you will be controlling the light emitted from and received by an LED/phototransistor pair. There are many

Basic Electronics Learning by doing Prof. T.S. Natarajan Department of Physics Indian Institute of Technology, Madras

Basic Electronics Learning by doing Prof. T.S. Natarajan Department of Physics Indian Institute of Technology, Madras Lecture 26 Mathematical operations Hello everybody! In our series of lectures on basic

Radio and Electronics Fundamentals

Amateur Radio License Class Radio and Electronics Fundamentals Presented by Steve Gallafent September 26, 2007 Radio and Electronics Fundamentals Voltage, Current, and Resistance Electric current is the

Build an Earth s Field Magnetic Observatory!

P a g e 1 Build an Earth s Field Magnetic Observatory! PART VII, Software Most of the FDM magnetometer signal processing, as well as the display functions are performed by a LabView Windows executable

Objective Type Questions 1. Why pure semiconductors are insulators at 0 o K? 2. What is effect of temperature on barrier voltage? 3.

Objective Type Questions 1. Why pure semiconductors are insulators at 0 o K? 2. What is effect of temperature on barrier voltage? 3. What is difference between electron and hole? 4. Why electrons have

In the name of God, the most merciful Electromagnetic Radiation Measurement

In the name of God, the most merciful Electromagnetic Radiation Measurement In these slides, many figures have been taken from the Internet during my search in Google. Due to the lack of space and diversity

Testing and Stabilizing Feedback Loops in Today s Power Supplies

Keywords Venable, frequency response analyzer, impedance, injection transformer, oscillator, feedback loop, Bode Plot, power supply design, open loop transfer function, voltage loop gain, error amplifier,

Government Polytechnic Muzaffarpur Name of the Lab: Applied Electronics Lab

Government Polytechnic Muzaffarpur Name of the Lab: Applied Electronics Lab Subject Code: 1620408 Experiment-1 Aim: To obtain the characteristics of field effect transistor (FET). Theory: The Field Effect

Signal Characteristics and Conditioning

Signal Characteristics and Conditioning Starting from the sensors, and working up into the system:. What characterizes the sensor signal types. Accuracy and Precision with respect to these signals 3. General

Original Input Stage frequency response measurement verification

Original Input Stage frequency response measurement verification By: branadic DUT: WELEC W04A, FW:..OS.09 ------------------------------------------------------------Measurement equipment: Signal Generator

Data acquisition and instrumentation. Data acquisition

Data acquisition and instrumentation START Lecture Sam Sadeghi Data acquisition 1 Humanistic Intelligence Body as a transducer,, data acquisition and signal processing machine Analysis of physiological

Single-phase Variable Frequency Switch Gear

Single-phase Variable Frequency Switch Gear Eric Motyl, Leslie Zeman Advisor: Professor Steven Gutschlag Department of Electrical and Computer Engineering Bradley University, Peoria, IL May 13, 2016 ABSTRACT

Measurement of Time Period of A Simple Pendulum using an Electronic Circuit

Measurement of Time Period of A Simple Pendulum using an Electronic Circuit Bhuvnesh, Phurailatpam Hemantakumar Department of Physics, Hindu College, University of Delhi Abstract:- This project was taken

INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad

1 P a g e INSTITUTE OF AERONAUTICAL ENGINEERING (Autonomous) Dundigal, Hyderabad - 500 043 ELECTRONICS AND COMMUNICATION ENGINEERING TUTORIAL QUESTION BANK Name : INTEGRATED CIRCUITS APPLICATIONS Code

AC CIRCUITS. Part 1: Inductance of a Coil. THEORY: If the current in a resistor R, a capacitor C, and/or an inductor L is given by:

AC CIRCUITS OBJECTIVE: To study the effect of alternating currents on various electrical quantities in circuits containing resistors, capacitors and inductors. Part 1: Inductance of a Coil THEORY: If the

Federal Urdu University of Arts, Science & Technology Islamabad Pakistan SECOND SEMESTER ELECTRONICS - I

SECOND SEMESTER ELECTRONICS - I BASIC ELECTRICAL & ELECTRONICS LAB DEPARTMENT OF ELECTRICAL ENGINEERING Prepared By: Checked By: Approved By: Engr. Yousaf Hameed Engr. M.Nasim Khan Dr.Noman Jafri Lecturer

Laboration: Frequency measurements and PWM DC motor. Embedded Electronics IE1206

Laboration: Frequency measurements and PWM DC motor. Embedded Electronics IE1206 Attention! To access the laboratory experiment you must have: booked a lab time in the reservation system (Daisy). completed

Introductory Electronics for Scientists and Engineers

Introductory Electronics for Scientists and Engineers Second Edition ROBERT E. SIMPSON University of New Hampshire Allyn and Bacon, Inc. Boston London Sydney Toronto Contents Preface xiü 1 Direct Current

ANALOG TO DIGITAL CONVERTER ANALOG INPUT

ANALOG INPUT Analog input involves sensing an electrical signal from some source external to the computer. This signal is generated as a result of some changing physical phenomenon such as air pressure,

Instrumentation Amplifiers

ECE 480 Application Note Instrumentation Amplifiers A guide to instrumentation amplifiers and how to proper use the INA326 Zane Crawford 3-21-2014 Abstract This document aims to introduce the reader to

ELC224 Final Review (12/10/2009) Name:

ELC224 Final Review (12/10/2009) Name: Select the correct answer to the problems 1 through 20. 1. A common-emitter amplifier that uses direct coupling is an example of a dc amplifier. 2. The frequency

IMPLEMENTATION OF QALU BASED SPWM CONTROLLER THROUGH FPGA. This Chapter presents an implementation of area efficient SPWM

3 Chapter 3 IMPLEMENTATION OF QALU BASED SPWM CONTROLLER THROUGH FPGA 3.1. Introduction This Chapter presents an implementation of area efficient SPWM control through single FPGA using Q-Format. The SPWM

Question Paper Code: 21398

Reg. No. : Question Paper Code: 21398 B.E./B.Tech. DEGREE EXAMINATION, MAY/JUNE 2013 Fourth Semester Electrical and Electronics Engineering EE2254 LINEAR INTEGRATED CIRCUITS AND APPLICATIONS (Regulation

ELECTRICAL ENGINEERING (CODE NO. 10) PAPER - I

ELECTRICAL ENGINEERING (CODE NO. 10) PAPER - I 1. Circuit theory Circuit Components, Network graphs, KCL, KVL, Circuit analysis methods: Nodal analysis, mesh analysis, basic network theorems; transient

THIRD SEMESTER DIPLOMA EXAMINATION IN ELECTRICAL & ELECTRONICS ENGINEERING, MARCH 2013 ELECTRONIC DEVICES AND CIRCUITS

REVISION-2010 Reg. No SUB CODE:3053 Signature THIRD SEMESTER DIPLOMA EXAMINATION IN ELECTRICAL & ELECTRONICS ENGINEERING, MARCH 2013 ELECTRONIC DEVICES AND CIRCUITS Time :3hours Maximum marks:100 PART

Contents. 1. Fundamentals of Amplification The Small-Signal Pentode 40. Acknowledgements. Some Useful Formulae

Contents Preface Acknowledgements Some Useful Formulae vii ix x 1. Fundamentals of Amplification 1 1.1: Basic Theory of Valves 2 1.2: Valve Diodes 2 1.3: Triodes 4 1.4: Anode Resistance, r a 6 1.5: Amplification

Laboratory Exercises for Analog Circuits and Electronics as Hardware Homework with Student Laptop Computer Instrumentation

Laboratory Exercises for Analog Circuits and Electronics as Hardware Homework with Student Laptop Computer Instrumentation Marion O. Hagler Department of Electrical and Computer Engineering Mississippi

60-HERTZ ELECTROMAGNETIC FIELD DETECTOR/INTERFACE SYSTEM

60-HERTZ ELECTROMAGNETIC FIELD DETECTOR/INTERFACE SYSTEM Design Review February 22, 2012 Kuei-Cheng Hsiang Gaurav Jaina Team No.13 ECE 445 Spring 2012 TA: Ryan May INTRODUCTION Ambient electromagnetic

Computer Controlled Curve Tracer

Computer Controlled Curve Tracer Christopher Curro The Cooper Union New York, NY Email: chris@curro.cc David Katz The Cooper Union New York, NY Email: katz3@cooper.edu Abstract A computer controlled curve

AT7450 2A-60V LED Step-Down Converter

FEATURES DESCRIPTION IN Max = 60 FB = 200m Frequency 52kHz I LED Max 2A On/Off input may be used for the Analog Dimming Thermal protection Cycle-by-cycle current limit I LOAD max =2A OUT from 0.2 to 55

Motion Integrated Sensor for Energy Efficient LED Lighting

Motion Integrated Sensor for Energy Efficient LED Lighting G V S Kranthi Kumar 1, Dr. Sastry V. Vedula 2, Mr. Umamaheswararao 3 Graduate student (M.Tech) Ph.D., FNAE, Sr. Member IEEE (Life) Sr. Professor