Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows:

Transcription

1 SCOPE: IMPROVED, QUAD, SPST ANALOG SWITCHES Device Type Generic Number DG4A(x)/883B DG4A(x)/883B 3 DG43A(x)/883B Case Outline(s). The case outlines shall be designated in Mil-Std-835 as follows: Outline Letter Mil-Std-835 Case Outline Package Code MAXIM SMD K E GDIP-T6 or CDIP-T6 6 LEAD CERDIP J6 L X CDFP4-F6 6 LEAD FLATPACK F6 Z CQCC-N -Pin Ceramic LCC L Absolute Maximum Ratings V + to V V GND to V-... 5V Logic Supply Voltage (V L ) to V- /... (GND-.3V) to 44Vdc Digital Inputs, V S, V D /...(V - ) -Vdc to (V + ) +Vdc or 3mA whichever occurs first. Continuous Current, Any terminal... 3mA Source or drain Current (Pulsed at ms, % duty cycle max)... ma Lead Temperature (soldering, seconds) C Storage Temperature C to +5 C Continuous Power Dissipation T A =+7 C 6 lead CERDIP(derate.mW/ C above +7 C) mW 6 lead FLATPACK(derate 6.mW/ C above +7 C) mW lead LCC (derate 9. mw/ C above +7 C) mW Junction Temperature T J C Thermal Resistance, Junction to Case, ΘJC: Case Outline 6 lead CERDIP C/W Case Outline 6 lead FLATPACK C/W Case Outline lead LCC C/W Thermal Resistance, Junction to Ambient, ΘJA: Case Outline 6 lead CERDIP C/W Case Outline 6 lead FLATPACK C/W Case Outline lead LCC C/W Recommended Operating Conditions Ambient Operating Range (T A ) C to +5 C Unipolar Supply Voltage (V + )....V (V - )..... V Bipolar Supply Voltage (V + ).... 5V (V - ) V Logic Supply Voltage (V L ) V NOTE : Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. NOTE : Signals on SX, DX or INX exceeding V + or V - are clamped by internal diodes. Limit forward current to maximum current ratings Electrical Characteristics of DG4A/4A Rev. B /43A /883B for SMD Page of

2 TABLE ELECTRICAL TESTS TEST Symbol CONDITIONS / -55 C <=T A <= +5 C Unless otherwise specified Drain-to-Source ON Resistance r DS(ON) V+=3.5V V IN =.8V V-=-3.5V I S =-ma V IN =.4V V D =±8.5V Group A Subgroup,3,3 Device type Min Max Units Ω Drain-to-Source ON Resistance Source OFF Drain OFF Source OFF Drain OFF Channel ON Input current with V IN low Input current with V IN high V IN =.8V or.4v / r V+=.8V V IN =.8V DS(ON) V-=V I S =-ma V IN =.4V V D =3.V 8.V V IN =.8V or.4v / I S(OFF) I D(OFF) I S(OFF) I D(OFF) I D(ON) + I S(ON) I IL I IH V+=6.5V V-=-6.5V V D =-5.5V V S =5.5V V+=6.5V V-=-6.5V V D =5.5V V S =-5.5V V+=6.5V V-=-6.5V V D =5.5V V S =V D =±5.5V Input under test=.8v, all others =.4V Input under test=.4v, all others =.8V V IN =.4V V IN =.8V V IN =.8V or.4v / V IN =.4V V IN =.8V V IN =.8V or.4v / V IN =.4V V IN =.8V V IN =.8V or.4v /,3,3,3, Ω na na na , , Electrical Characteristics of DG4A/4A/43A/ Rev. B /883B for SMD Page 3 of

3 TABLE ELECTRICAL TESTS TEST Symbol CONDITIONS / -55 C <=T A <= +5 C Unless otherwise specified Turn ON time t ON C L =35pF, V S =±V, R L =3Ω See Figure 4, See Figure 4, V+=V, V-=V, V S =±8V, C L =35pF, R L =3Ω Turn OFF time t OFF C L =35pF, V S =±V, R L =3Ω See Figure 4, Charge Injection Positive Supply Current Negative Supply Current Logic Supply Current Ground Current Q I+ I- I L I GND See Figure 4, V+=V, V-=V, V S =±8V, C L =35pF, R L =3Ω See Figure 5, V GEN =V, R GEN =Ω, C L =nf See Figure 5, V GEN =6.V, R GEN =Ω,C L =nf, V+=V, V-=V V+=6.5V, V-=-6.5V, V IN =V or 5.V V+=3.V, V-=V, V IN =V or 5V, V L =5.5V V+=6.5V, V-=-6.5V, V IN =V or 5.V V+=3.V, V-=V, V IN =V or 5V, V L =5.5V V+=6.5V, V-=-6.5V, V IN =V or 5.V V+=3.V, V-=V, V IN =V or 5V, V L =5.5V V+=6.5V, V-=-6.5V, V IN =V or 5.V V+=3.V, V-=V, V IN =V or 5V, V L =5.5V Group A Subgroup 9, 9, 9, 9, Device type 9 Min Max Units ns ns pc NOTE : V+=5V, V-=-5V, V L =5V GND = V, unless otherwise specified. NOTE : V IN =input voltage to perform proper function Electrical Characteristics of DG4A/4A/43A/ Rev. B /883B for SMD Page 4 of

4 Ordering Information. SMD # PKG.Code DG4AK/883B MEA J6 DG4AL/883B MXC F6 DG4AZ/883B MA L DG4AK/883B MEA J6 DG4AL/883B MXC F6 DG4AZ/883B MA L 3 DG43AK/883B MEA J6 3 DG43AL/883B MXC F6 3 DG43AZ/883B MA L FIGURE TERMINAL CONNECTIONS DEVICE TYPES,, 3 CASE OUTLINES SMD=E OR X MAXIM= K OR L SMD = MAXIM = Z TERMINAL NUMBER TERMINAL SYMBOL TERMINAL SYMBOL INPUT IN NC DRAIN D INPUT IN 3 SOURCE S DRAIN D 4 V- SOURCE S 5 GROUND GND V- 6 SOURCE 4 S4 NC 7 DRAIN 4 D4 GROUND GND 8 INPUT 4 IN4 SOURCE 4 S4 9 INPUT 3 IN3 DRAIN 4 D4 DRAIN 3 D3 INPUT 4 IN4 SOURCE 3 S3 NC V L INPUT 3 IN3 3 V+ DRAIN 3 D3 4 SOURCE S SOURCE 3 S3 5 DRAIN D V L 6 INPUT IN NC 7 V+ 8 SOURCE S 9 DRAIN D INPUT IN FIGURE. TRUTH TABLES DG4 DG4 DG43 DG43 SWITCH,,4,,4,4 LOGIC ON OFF OFF ON OFF ON ON OFF Electrical Characteristics of DG4A/4A/43A/883B Rev. B for SMD Page 5 of

5 FIGURE 3: Block Diagrams: See commercial datasheet or SMD Electrical Characteristics of DG4A/4A/43A/883B Rev. B for SMD Page 6 of FIGURE 4: TEST CIRCUITS: Switching Times. See commerical datasheet or SMD Electrical Characteristics of DG4A/4A/43A/883B Rev. B for SMD Page 7 of FIGURE 5: Charge Injection test circuit waveforms. See Commercial datasheet or SMD Electrical Characteristics of DG4A/4A/43A/883B Rev. B for SMD Page 8 of

6 QUALITY ASSURANCE Sampling inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in Mil- Std-883. Screening shall be in accordance with Method 54 of Mil-Std-883. Burn-in test Method 5:. Test Condition, A, B, C, or D.. TA = +5C minimum. 3. Interim final electrical test requirements shall be specified in Table. Quality conformance inspection shall be in accordance with Method 55 of Mil-Std-883, including Groups A, B, C, D inspection. Group A inspection:. Tests as specified in Table.. Selected subgroups in Table, Method 55 of Mil-Std-883 shall be omitted. Group C D inspections: a. End-point electrical parameters shall be specified in Table. b. Steady-state life test, Method 5 of Mil-Std-883:. Test condition A, B, C, D.. TA = +5C, minimum 3. Test duration, hours, except as permitted by Method 5 of Mil-Std-883. TABLE. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 54 Final Electrical Parameters Method 55 Group A Test Requirements Method 55 Group C D End-Point Electrical Parameters Method 55 Subgroups per Method 55, Table *,, 3, 9,,,, 3, 9,, * PDA applies to Subgroup only Electrical Characteristics of DG4A/4A/43A/883B Rev. B for SMD Page 9 of