Medium Voltage Thyristor Types K2359TD600 to K2359TD650 Old Type No.: P1063DH60-65

Transcription

1 WESTCODE An IXYS Company Date:- 2 Aug, 22 Data Sheet Issue:- 1 Medium Voltage Thyristor Types K2359TD6 to K2359TD65 Old Type No.: P163DH6-65 Absolute Maximum Ratings VOLTAGE RATINGS MAXIMUM LIMITS V DRM Repetitive peak off-state voltage, (note 1) 6-65 V V DSM Non-repetitive peak off-state voltage, (note 1) 6-65 V V RRM Repetitive peak reverse voltage, (note 1) 6-65 V V RSM Non-repetitive peak reverse voltage, (note 1) V UNITS OTHER RATINGS MAXIMUM LIMITS I T(AV)M Maximum average on-state current, T sink=55 C, (note 2) 2359 A I T(AV)M Maximum average on-state current. T sink=85 C, (note 2) 1647 A I T(AV)M Maximum average on-state current. T sink=85 C, (note 3) 122 A I T(RMS) Nominal RMS on-state current, T sink=25 C, (note 2) 4614 A I T(d.c.) D.C. on-state current, T sink=25 C, (note 4) 412 A I TSM Peak non-repetitive surge t p=1ms, V rm=.6v RRM, (note 5) 27 A I TSM2 Peak non-repetitive surge t p=1ms, V rm 1V, (note 5) 3 A I 2 t I 2 t capacity for fusing t p=1ms, V rm=.6v RRM, (note 5) A 2 s I 2 t I 2 t capacity for fusing t p=1ms, V rm 1V, (note 5) A 2 s UNITS (di/dt) cr Critical rate of rise of on-state current (repetitive), (Note 6) 2 A/µs Critical rate of rise of on-state current (non-repetitive), (Note 6) 4 A/µs V RGM Peak reverse gate voltage 5 V P G(AV) Mean forward gate power 4 W P GM Peak forward gate power 6 W T j op Operating temperature range -4 to +115 C T stg Storage temperature range -4 to +15 C Notes:- 1) De-rating factor of.13% per C is applicable for T j below 25 C. 2) Double side cooled, single phase; 5Hz, 18 half-sinewave. 3) Single side cooled, single phase; 5Hz, 18 half-sinewave. 4) Double side cooled. 5) Half-sinewave, 115 C T j initial. 6) V D=67% V DRM, I FG=2A, t r.5µs, T case=115 C. Data Sheet. Types K2359TD6 to K2359TD65 Page 1 of 11 August, 22

2 WESTCODE An IXYS Company Medium Voltage Thyristor Type Characteristics PARAMETER MIN. TYP. MAX. TEST CONDITIONS (Note 1) UNITS V TM Maximum peak on-state voltage I TM=2A V V T Threshold voltage V r T Slope resistance mω (dv/dt) cr Critical rate of rise of off-state voltage V D=8% V DRM, linear ramp, gate o/c V/µs I DRM Peak off-state current Rated V DRM ma I RRM Peak reverse current Rated V RRM ma V tr On-state recovery voltage I T=3 I T(AV)M, t p=1ms, T case=25 C V V GT Gate trigger voltage T j=25 C V D=1V, I T=3A V I GT Gate trigger current ma V GD Gate non-trigger voltage Rated V DRM V I H Holding current T j=25 C ma t gd Gate-controlled turn-on delay time V D=67% V DRM, I T=15A, di/dt=6a/µs, µs t gt Turn-on time I FG=2A, t r=.5µs, T j=25 C µs Q rr Recovered charge µc Q ra Recovered charge, 5% Chord I TM=2A, t p=2µs, di/dt=1a/µs, µc I rm Reverse recovery current V r=5v A t rr Reverse recovery time µs t q R thjk Turn-off time Thermal resistance, junction to heatsink I TM=2A, t p=2µs, di/dt=1a/µs, V r=1v, V dr=8%v DRM, dv dr/dt=2v/µs I TM=2A, t p=2µs, di/dt=1a/µs, V r=1v, V dr=8%v DRM, dv dr/dt=2v/µs Double side cooled K/W Single side cooled K/W F Mounting force kn W t Weight kg µs Notes:- 1) Unless otherwise indicated T j=115 C. Data Sheet. Types K2359TD6 to K2359TD65 Page 2 of 11 August, 22

3 WESTCODE An IXYS Company Medium Voltage Thyristor Type Notes on Ratings and Characteristics 1. Voltage Grade Table Voltage Grade V DRM V DSM V RRM V RSM V D V R V V DC V Extension of Voltage Grades This report is applicable to other voltage grades when supply has been agreed by Sales/Production. 3. De-rating Factor A blocking voltage de-rating factor of.13%/ C is applicable to this device for T j below 25 C. 4. Repetitive dv/dt Standard dv/dt is 1V/µs. 5. Frequency Ratings The curves illustrated in figures 17 & 18 are for guidance only and are superseded by the maximum ratings shown on page 1. For operation above line frequency, please consult the factory for assistance. 6. Snubber Components When selecting snubber components, care must be taken not to use excessively large values of snubber capacitor or excessively small values of snubber resistor. Such excessive component values may lead to device damage due to the large resultant values of snubber discharge current. If required, please consult the factory for assistance. 7. Rate of rise of on-state current The maximum un-primed rate of rise of on-state current must not exceed 4A/µs at any time during turnon on a non-repetitive basis. For repetitive performance, the on-state rate of rise of current must not exceed 2A/µs at any time during turn-on. Note that these values of rate of rise of current apply to the total device current including that from any local snubber network. 8. Square wave frequency ratings These ratings are given for load component rate of rise of on-state current of 5A/µs. 9. Duty cycle lines The 1% duty cycle is represented on the frequency ratings by a straight line. Other duties can be included as parallel to the first. Data Sheet. Types K2359TD6 to K2359TD65 Page 3 of 11 August, 22

4 WESTCODE An IXYS Company Medium Voltage Thyristor Type 1. Gate Drive The nominal requirement for a typical gate drive is illustrated below. An open circuit voltage of at least 3V is assumed. This gate drive must be applied when using the full di/dt capability of the device. I GM 4A/µs I G t p1 The magnitude of I GM should be between five and ten times I GT, which is shown on page 2. Its duration (t p1 ) should be 2µs or sufficient to allow the anode current to reach ten times I L, whichever is greater. Otherwise, an increase in pulse current could be needed to supply the necessary charge to trigger. The back-porch current I G should remain flowing for the same duration as the anode current and have a magnitude in the order of 1.5 times I GT. 11. Computer Modelling Parameters I AV 11.1 Device Dissipation Calculations V = T + 2 T V + 4 ff 2 ff r T r T W AV and: W AV T = R T = T Where V T =1.391V, r T =.36mΩ, R th = Supplementary thermal impedance, see table below and ff = Form factor, see table below. th j max T Hs Supplementary Thermal Impedance Conduction Angle d.c. Square wave Double Side Cooled Square wave Single Side Cooled Sine wave Double Side Cooled Sine wave Single Side Cooled Form Factors Conduction Angle d.c. Square wave Sine wave Data Sheet. Types K2359TD6 to K2359TD65 Page 4 of 11 August, 22

5 WESTCODE An IXYS Company Medium Voltage Thyristor Type 11.2 Calculating V T using ABCD Coefficients The on-state characteristic I T vs. V T, on page 6 is represented in two ways; (i) the well established V T and r T tangent used for rating purposes and (ii) a set of constants A, B, C, D, forming the coefficients of the representative equation for V T in terms of I T given below: V T = A + B ln ( IT ) + C IT + D IT The constants, derived by curve fitting software, are given below for both hot and cold characteristics. The resulting values for V T agree with the true device characteristic over a current range, which is limited to that plotted. 25 C Coefficients 115 C Coefficients A A B B C C D D D.C. Thermal Impedance Calculation p = n t = p= 1 r r p 1 e t τ p Where p = 1 to n, n is the number of terms in the series and: t = Duration of heating pulse in seconds. r t = Thermal resistance at time t. r p = Amplitude of p th term. τ p = Time Constant of r th term. The coefficients for this device are shown in the tables below: D.C. Double Side Cooled Term r p τ p D.C. Single Side Cooled Term r p τ p Data Sheet. Types K2359TD6 to K2359TD65 Page 5 of 11 August, 22

6 WESTCODE An IXYS Company Medium Voltage Thyristor Type Curves Figure 1 - On-state characteristics of Limit device Figure 2 - Transient thermal impedance 1.1 SSC.17K/W T j = 25 C T j = 115 C.1 DSC.85K/W Instantaneous On-state current - I TM (A) 1 Transient thermal impedance (K/W) Instantaneous On-state voltage - V TM (V).1 1E Time (s) Figure 3 - Gate characteristics - Trigger limits Figure 4 - Gate characteristics - Power curves 6 14 T j =25 C T j =25 C 12 Max V G dc 1 4 Max V G dc I GT, V GT Gate Voltage - V G (V) Gate Voltage - V G (V) 8 6 P G Max 6W dc C 25 C -1 C -4 C 4 P G 4W dc Min V G dc 2 I GD, V GD Min V G dc Gate Current - I G (A) Gate Current - I G (A) Data Sheet. Types K2359TD6 to K2359TD65 Page 6 of 11 August, 22

7 WESTCODE An IXYS Company Medium Voltage Thyristor Type Figure 5 - Total recovered charge, Q rr Figure 6 - Recovered charge, Q ra (5% chord) 1 T j =115 C 1 T j =115 C 4A 2A Recovered charge - Q rr (µc) 1 1A 5A Recovered charge - Q ra, 5% chord (µc) 1 4A 2A 1A 5A di/dt (A/µs) di/dt (A/µs) Figure 7 - Peak reverse recovery current, I rm 1 T j =115 C Figure 8 - Maximum recovery time, t rr (5% chord) 1 T j =115 C Reverse recovery current - I rm (A) 1 4A 2A 1A 5A Reverse recovery time (5% chord) - t rr (µs) 4A 2A 1A 5A di/dt (A/µs) di/dt (A/µs) Data Sheet. Types K2359TD6 to K2359TD65 Page 7 of 11 August, 22

8 WESTCODE An IXYS Company Medium Voltage Thyristor Type Figure 9 On-state current vs. Power dissipation Double Side Cooled (Sine wave) Figure 1 On-state current vs. Heatsink temperature - Double Side Cooled (Sine wave) Maximum forward dissipation (W) Maximum permissable heatsink temperature ( C) Mean forward current (A) (Whole cycle averaged) Figure 11 On-state current vs. Power dissipation Double Side Cooled (Square wave) Mean forward current (A) (Whole cycle averaged) Figure 12 On-state current vs. Heatsink temperature Double Side Cooled (Square wave) Maximum forward dissipation (W) d.c Maximum permissible heatsink temperature ( C) d.c Mean Forward Current (Amps) (Whole Cycle Averaged) Mean Forward Current (Amps) (Whole Cycle Averaged) Data Sheet. Types K2359TD6 to K2359TD65 Page 8 of 11 August, 22

9 WESTCODE An IXYS Company Medium Voltage Thyristor Type Figure 13 On-state current vs. Power dissipation Single Side Cooled (Sine wave) Figure 14 On-state current vs. Heatsink temperature Single Side Cooled (Sine wave) Maximum forward dissipation (W) Maximum permissable heatsink temperature ( C) Mean forward current (A) (Whole cycle averaged) Figure 15 On-state current vs. Power dissipation Single Side Cooled (Square wave) Mean forward current (A) (Whole cycle averaged) Figure 16 On-state current vs. Heatsink temperature Single Side Cooled (Square wave) Maximum forward dissipation (W) d.c Maximum permissible heatsink temperature ( C) d.c Mean Forward Current (Amps) (Whole Cycle Averaged) Mean Forward Current (Amps) (Whole Cycle Averaged) Data Sheet. Types K2359TD6 to K2359TD65 Page 9 of 11 August, 22

10 WESTCODE An IXYS Company Medium Voltage Thyristor Type Figure 17 Square Wave Frequency Ratings Figure 18 Sine Wave Frequency Ratings 1.E+5 5A 1.E+5 5A 1% Duty Cycle T Hs =55 C 1A 1A 1% Duty Cycle 1.E+4 1.E+4 2A 2A Frequency (Hz) Frequency (Hz) 1.E+3 4A 4A 1.E+3 6A 6A 1.E+2 T Hs =55 C di/dt=5a/µs 1.E+2 1.E-5 1.E-4 1.E-3 1.E-2 Pulse width (s) 1.E+1 1.E-5 1.E-4 1.E-3 1.E-2 Pulse Width (s) Figure 19 - Maximum surge and I 2 t Ratings 1 1.E+8 Total peak half sine surge current (A) 1 I 2 t: V RRM 1V I 2 t: 6% V RRM I TSM : V RRM 1V I TSM : 6% V RRM 1.E+7 Maximum I 2 t (A 2 s) T j (initial) = 115 C E+6 Duration of surge (ms) Duration of surge 5Hz) Data Sheet. Types K2359TD6 to K2359TD65 Page 1 of 11 August, 22

11 WESTCODE An IXYS Company Medium Voltage Thyristor Type Outline Drawing & Ordering Information ORDERING INFORMATION K2359 TD Fixed Type Code Fixed outline code Order code: K2359TD62 62V V RRM, 35mm clamp height capsule. (Please quote 1 digit code as below) Voltage code V DRM/ Fixed turn-off time code IXYS Semiconductor GmbH Edisonstraße 15 D Lampertheim Tel: Fax: marcom@ixys.de IXYS Corporation 354 Bassett Street Santa Clara CA 9554 USA Tel: +1 (48) Fax: +1 (48) sales@ixys.net WESTCODE An IXYS Company Westcode Semiconductors Ltd PO Box 57 Chippenham Wiltshire SN15 1JL Tel: +44 () Fax: +44 () WSL.sales@westcode,com Westcode Semiconductors Inc 327 Cherry Avenue Long Beach CA 987 USA Tel: +1 (562) Fax: +1 (562) WSI.sales@westcode.com The information contained herein is confidential and is protected by Copyright. The information may not be used or disclosed except with the written permission of and in the manner permitted by the proprietors Westcode Semiconductors Ltd. Westcode Semiconductors Ltd. In the interest of product improvement, Westcode reserves the right to change specifications at any time without prior notice. Devices with a suffix code (2-letter or letter/digit/letter combination) added to their generic code are not necessarily subject to the conditions and limits contained in this report. Data Sheet. Types K2359TD6 to K2359TD65 Page 11 of 11 August, 22