Transformer Protection Principles
|
|
|
- Harvey Owen
- 6 years ago
- Views:
Transcription
1 Transformer Protection Principles 1. Introduction Transformers are a critical and expensive component of the power system. Due to the long lead time for repair of and replacement of transformers, a major goal of transformer protection is limiting the damage to a faulted transformer. Some protection functions, such as overexcitation protection and temperature-based protection may aid this goal by identifying operating conditions that may cause transformer failure. The comprehensive transformer protection provided by multiple function protective relays is appropriate for critical transformers of all applications. Conditions Internal Winding Phase-Phase, Phase-s Winding inter-turn faults Core insulation failure, shorted laminations Tank faults Overfluxing Volts/Hz () External Overloads Thermal (49) Protection Philosophy (), overcurrent (51, 51N) Restricted ground fault protection () (), Buchholz relay, (), Buchholz relay, sudden pressure relay () Overfluxing Volts/Hz () External system short circuits (), Buchholz relay and tank-ground protection Time overcurrent (51, 51G), Instantaneous overcurrent (50, ) abnormal operating conditions (overfluxing, overloading, overvoltage) external faults 2. Transformer Protection Overview The type of protection for the transformers varies depending on the application and the importance of the transformer. Transformers are protected primarily against faults and overloads. The type of protection used should minimize the time of disconnection for faults within the transformer and to reduce the risk of catastrophic failure to simplify eventual repair. Any extended operation of the transformer under abnormal condition such as faults or overloads compromises the life of the transformer, which means adequate protection should be provided for quicker isolation of the transformer under such conditions. 3. Transformer Failures Failures in transformers can be classified into winding failures due to short circuits (turn-turn faults, phase-phase faults, phase-ground, open winding) core faults (core insulation failure, shorted laminations) terminal failures (open leads, loose connections, short circuits) on-load tap changer failures (mechanical, electrical, short circuit, overheating) 4. Innovative GE Multilin Solutions to Transformer Protection Applications 4.1 Characteristic The major operating challenge to transformer differential protection is maintaining security during CT saturation for external faults while maintaining sensitivity to detect low magnitude internal faults. CT saturation reduces the secondary output current from the CT, and causes a false differential current to appear to the relay. GE Multilin differential relays meet this challenge in the following ways: the restraint current is based on the maximum measured winding current, as opposed to the traditional magnitude sum of the currents. This ensures ideal restraint for the actual fault condition, balancing sensitivity and security. the differential element uses a dual slope-dual breakpoint characteristic. The differential element can be set to account for both DC and AC saturation of the CTs, ensuring security, while maintaining sensitivity. Available in the T60, T35. Transformer Protection Principles 45
2 4.2 Inrush Inhibit during Transformer Energization: The transformer energization resembles the condition of an internal fault. If no inhibiting mechanism is provided, the differential element will trip. The magnetizing inrush current has significant 2 nd harmonic content. The level of 2 nd harmonic current can be used to differentiate between inrush and a fault condition. The UR T60 and T35 GE Multilin transformer relays use two different 2 nd harmonic modes to inhibit the differential element for inrush. Traditional 2 nd harmonic blocking The traditional 2 nd harmonic restraint responds to the ratio of the magnitudes of the 2 nd harmonic and the fundamental frequency currents. Adaptive 2 nd harmonic blocking The adaptive 2 nd harmonic blocking responds to both magnitudes and phase angles of the 2 nd harmonic and the fundamental frequency currents. The differential element correctly distinguishes between faults and transformer energization, when the 2 nd harmonic current is less than the entered 2 nd harmonic setting. While levels of 2 nd harmonic during inrush often do not go below 20%, many transformers are susceptible of generating lower 2 nd harmonic current during energization. Setting the 2 nd harmonic restraint below 20% may result in incorrect inhibit of the differential element during some internal fault events. The adaptive 2 nd harmonic blocking allows settings in the traditional 20% range, while maintaining the security of the differential element against inrush. Available in the T60, T35. An alternative method for inrush inhibit is also available, where either current, voltage, or breaker status is used to indicate a de-energized transformer. The threshold can be lowered during energization of the transformer as indicated either by breaker contact, current or voltage sensing, and will last for a settable time delay. This allows settings of less than 20% for inrush inhibit during transformer energization. Available in the Sensitive Ground Fault Protection to limit Transformer Damage and overcurrent protection do not provide adequate protection for wye-connected windings with grounded neutrals. Faults close to the neutral produces lesser fault current as shown by the current distribution curve. The restricted ground fault function can be used to provide differential protection for such ground faults, down to faults at 5% of the transformer winding. Restricted ground fault protection can be a low impedance differential function or a high impedance differential function. The low impedance function has the advantage to being able to precisely set the sensitivity to meet the application requirement. This sensitive protection limits the damage to the transformer to allow quicker repair. The restricted ground fault element uses adaptive restraint based on symmetrical components to provide security during external phase faults with significant CT error. This permits the function to maximize sensitivity without any time delay. Available in the 745, T Overflux Protection Transformer overfluxing can be a result of Low system frequency A transformer is designed to operate at or below a maximum magnetic flux density in the transformer core. Above this design limit the eddy currents in the core and nearby conductive components cause overheating which within a very short time may cause severe damage. The magnetic flux in the core is proportional to the voltage applied to the winding divided by the impedance of the winding. The flux in the core increases with either increasing voltage or decreasing frequency. During startup or shutdown of generator-connected transformers, or following a load rejection, the transformer may experience an excessive ratio of volts to hertz, that is, become overexcited. When a transformer core is overexcited, the core is operating in a non-linear magnetic region, and creates harmonic components in the exciting current. A significant amount of current at the 5th harmonic is characteristic of overexcitation. Available in the 745, T60, and T35. current for impedance grounded neutral transformer for faults at different % of the winding. 46 Transformer Protection Principles
3 4.5 Winding hot-spot temperature protection The transformer winding hot-spot temperature is another quantity that should be used for protection of transformers. Protection based on winding hot-spot temperature can potentially prevent short circuits and catastrophic transformer failure, as excessive winding hot-spot temperatures cause degradation and eventual failure of the winding insulation. The ambient temperature, transformer loading, and transformer design determine the winding temperature. Temperature based protection functions alarm or trip when certain temperature conditions are met. GE Multilin relays use IEEE C57.91 compliant thermal models to calculate the winding hot-spot temperature and the loss of life of the winding insulation. The top-oil temperature may be directly measured, or calculated from the ambient temperature, load current, and transformer characteristics. In addition, the calculations may use a monthly model of ambient temperature, eliminating the need for external connections to the transformer and relay. This winding hot-spot temperature and transformer loss of life information is used in thermal overload protection to provide alarming or tripping when unacceptable degradation of the transformer winding insulation is occurring. Available in 745, T Application Capabilities GE Multilin transformer protection relays are suitable for different transformer protection applications, including medium voltage and high voltage transformers of any size, dual secondary transformers, auto-transformers, three-winding transformers, transformers with dual-breaker terminals. In addition, these relays are designed for both new and retrofit installations. New installations typically use wye-connected CTs, and internally compensate the measured currents for the phase shift of the protected transformer. Traditional installations may use delta-connected or wye-connected CTs that externally compensate the measured currents for the phase shift of the protected transformer. GE Multilin accommodates both methods as simple configuration settings. Beyond these typical applications, GE Multilin transformer protection relays can be applied on more advanced applications. 4.7 Phase shift transformers Phase shift transformers phase shift transformers purposely introduce a variable phase shift between the primary and secondary voltage. This phase shift is not a multiple of 30 degree, but is adjustable in small increments, to allow operators to change the phase angle between parts of the power system to control power flow in the system. GE Multilin relays are successfully applied for protecting phase shifting transformers. 4.8 Split-phase autotransformers Split-phase autotransformers are single-phase autotransformers connected in parallel to make a large three-phase bank. The differential protection from GE Multilin can be used to identify turn-turn faults in one of the auto-transformers without operating the entire bank. 5. Typical applications This section highlights some typical application of GE Multilin transformer protection relays. This section is not intended as a comprehensive list of possible applications. For questions about the correct relay for a specific application, please contact GE Multilin. Transformers 750kVA and above, MV Windings Additional auxiliary 745-W2-P5-G5-HI-T T35-N00-HCH-F8N-H6P-MXX-PXX-UXX-WXX T60-N00-HCH-F8N-H6P-MXX-PXX-UXX-WXX + Harsh Environment Option 745-W2-P5-G5-HI-T-H T35-N00-ACH-F8N-H6P-MXX-PXX-UXX-WXX T60-N00-ACH-F8N-H6P-MXX-PXX-UXX-WXX W2-P5-G5-HI-T + T35-N00-HPH-F8N-H6P-MXX-P4L-UXX-WXX T60-N00-HPH-F8N-H6P-MXX-P4L-UXX-WXX Transformer Protection Principles 47
4 Power Transformers, Dual MV Secondary Windings Additional 50N auxiliary Neutral ground fault 745-W3-P5-G5-HI-T + Harsh Environment Option 745-W3-P5-G5-HI-T-H T35-N00-ACH-F8L-H6P-M8N-PXX-UXX-WXX T60-N00-ACH-F8L-H6P-M8N-PXX-UXX-WXX W3-P5-G5-HI-T + T35-N00-HPH-F8L-H6P-M8N -P4L-UXX-WXX T60-N00-HPH-F8L-H6P-M8N -P4L-UXX-WXX Power Transformers, HV Windings Additional auxiliary (both windings) T60-N00-HCH-F8N-H6P-MXX-PXX-UXX-WXX T35-N00-HCH-F8N-H6P-MXX-PXX-UXX-WXX 745-W2-P5-G5-HI-T W2-P5-G5-HI-T + Additional (87G,,, ) 745-W2-P5-G5-HI-R-T T35-N00-HPH-F8N-H6P-MXX-P4L-UXX-WXX T60-N00-HPH-F8N-H6P-MXX-P4L-UXX-WXX Power Transformers, HV Windings, Dual-Breaker Source auxiliary Additional + + Additional T35-N00-HPH-F8L-H6P-M8N-P4L-UXX-WXX T60-N00-HPH-F8L-H6P-M8N-P4L-UXX-WXX 48 Transformer Protection Principles
5 Auto-Transformer Additional auxiliary (both sources) T60-N00-HCH-F8N-H6P-MXX-PXX-UXX-WXX T35-N00-HCH-F8N-H6P-MXX-PXX-UXX-WXX + + Additional T35-N00-HPH-F8N-H6P-MXX-P4L-UXX-WXX T60-N00-HPH-F8N-H6P-MXX-P4L-UXX-WXX Auto-Transformer, Dual-Breaker Terminals Additional auxiliary + + Additional T35-N00-HPH-F8L-H6P-M8N-P4L-UXX-WXX T60-N00-HPH-F8L-H6P-M8N-P4L-UXX-WXX Auto with Dual-Breaker on both sides and loaded tertiary auxiliary Additional T35-N00-HCH-F8L-H6P-M8N-PXX-U8N-W6P + T35-N00-HCH-F8L-H6P-M8N-PXX-UXX-W6P T35-N00-HPH-F8L-H6P-M8N-P4L-U8N-W6P Transformer Protection Principles 49
6 Generator Step Up Transformer Additional 51 auxiliary 51G Ground Fault T60-N00-HPH-F8L-H6P-M8N-P4L-UXX-WXX Thermal Overload Protection Additional TT/TO 49 auxiliary Top Oil Temperature, RTD or Transducer Winding hot-spot temperature, loss-of-life Thermal overload protection T60-N00-HCH-F8N-H6P-MXX-PXX-UXX-W5E 745-W2-P5-G5-HI-L-T + T60-N00-HCH-F8L-H6P-M8N-PXX-UXX-W5E 745-W2-P5-G5-HI-L-T + Additional T60-N00-HCH-F8N-H6P-MXX-PXX-UXX-W5E 745-W2-P5-G5-HI-L-R-T T60-N00-HPH-F8N-H6P-MXX-P4L-UXX-W5E Distribution Transformer with no load-side Circuit Breaker 51 auxiliary T35-N00-HCH-F8N-H6P-M8N-PXX-U8N-WXX T35-N00-HPH-F8N-H6P-M8N-P4L-U8N-WXX 6. References IEEE Std C IEEE Guide for Protective Relay Applications to Power Transformers 50 Transformer Protection Principles v3
Transformer Protection
Transformer Protection Transformer Protection Outline Fuses Protection Example Overcurrent Protection Differential Relaying Current Matching Phase Shift Compensation Tap Changing Under Load Magnetizing
Modern transformer relays include a comprehensive set of protective elements to protect transformers from faults and abnormal operating conditions
1 Transmission transformers are important links in the bulk power system. They allow transfer of power from generation centers, up to the high-voltage grid, and to bulk electric substations for distribution
Transformer Fault Categories
Transformer Fault Categories 1. Winding and terminal faults 2. Sustained or uncleared external faults 3. Abnormal operating conditions such as overload, overvoltage and overfluxing 4. Core faults 1 (1)
Detecting and Managing Geomagnetically Induced Currents With Relays
Detecting and Managing Geomagnetically Induced Currents With Relays Copyright SEL 2013 Transformer Relay Connections Voltage Current Control RTDs Transformer Protective Relay Measures differential current
Protecting power transformers from common adverse conditions
Protecting power transformers from common adverse conditions by Ali Kazemi, and Casper Labuschagne, Schweitzer Engineering Laboratories Power transformers of various size and configuration are used throughout
Improving Transformer Protection
Omaha, NB October 12, 2017 Improving Transformer Protection Wayne Hartmann VP, Customer Excellence Senior Member, IEEE Wayne Hartmann Senior VP, Customer Excellence Speaker Bio whartmann@beckwithelectric.com
This webinar brought to you by the Relion product family Advanced protection and control IEDs from ABB
This webinar brought to you by the Relion product family Advanced protection and control IEDs from ABB Relion. Thinking beyond the box. Designed to seamlessly consolidate functions, Relion relays are smarter,
Transformer Protection
Transformer Protection Nature of transformer faults TXs, being static, totally enclosed and oil immersed develop faults only rarely but consequences large. Three main classes of faults. 1) Faults in Auxiliary
Hands On Relay School Open Lecture Transformer Differential Protection Scott Cooper
Hands On Relay School Open Lecture Transformer Differential Protection Scott Cooper Transformer Differential Protection ntroduction: Transformer differential protection schemes are ubiquitous to almost
COPYRIGHTED MATERIAL. Index
Index Note: Bold italic type refers to entries in the Table of Contents, refers to a Standard Title and Reference number and # refers to a specific standard within the buff book 91, 40, 48* 100, 8, 22*,
Power System Protection
I Power System Protection Arun Phadke Virginia Polytechnic Institute 1 Transfor mer Protection Alexander Apostolov, John Apple yard, Ahmed Elneweihi, Robert Haas, and Glenn W Swift 1-1 Ty pes of Transformer
Protection of a 138/34.5 kv transformer using SEL relay
Scholars' Mine Masters Theses Student Theses and Dissertations Fall 2016 Protection of a 138/34.5 kv transformer using SEL 387-6 relay Aamani Lakkaraju Follow this and additional works at: http://scholarsmine.mst.edu/masters_theses
Transformer protection IED RET 670
Gunnar Stranne Transformer protection IED RET 670 Santiago Septiembre 5, 2006 1 Transformer protection IED RET670 2 Introduction features and applications Differential protection functions Restricted Earth
Generator Protection GENERATOR CONTROL AND PROTECTION
Generator Protection Generator Protection Introduction Device Numbers Symmetrical Components Fault Current Behavior Generator Grounding Stator Phase Fault (87G) Field Ground Fault (64F) Stator Ground Fault
System Protection and Control Subcommittee
Power Plant and Transmission System Protection Coordination Volts Per Hertz (24), Undervoltage (27), Overvoltage (59), and Under/Overfrequency (81) Protection System Protection and Control Subcommittee
Catastrophic Relay Misoperations and Successful Relay Operation
Catastrophic Relay Misoperations and Successful Relay Operation Steve Turner (Beckwith Electric Co., Inc.) Introduction This paper provides detailed technical analysis of several catastrophic relay misoperations
g GE POWER MANAGEMENT
745 FREQUENTLY ASKED QUESTIONS 1 I get a communication error with the relay when I try to store a setpoint. This error can occur for several different reasons. First of all, verify that the address is
Hands On Relay School Open Lecture Transformer Differential Protection Scott Cooper
Hands On Relay School Open Lecture Transformer Differential Protection Scott Cooper Transformer Differential Protection ntroduction: Transformer differential protection schemes are ubiquitous to almost
Shortcomings of the Low impedance Restricted Earth Fault function as applied to an Auto Transformer. Anura Perera, Paul Keller
Shortcomings of the Low impedance Restricted Earth Fault function as applied to an Auto Transformer Anura Perera, Paul Keller System Operator - Eskom Transmission Introduction During the design phase of
Power System Protection. Dr. Lionel R. Orama Exclusa, PE Week 3
Power System Protection Dr. Lionel R. Orama Exclusa, PE Week 3 Operating Principles: Electromagnetic Attraction Relays Readings-Mason Chapters & 3 Operating quantities Electromagnetic attraction Response
www. ElectricalPartManuals. com Transformer Differential Relay MD32T Transformer Differential Relay
Transformer Differential Relay The MD3T Transformer Differential Relay is a member of Cooper Power Systems Edison line of microprocessor based protective relays. The MD3T relay offers the following functions:
PJM Manual 07:: PJM Protection Standards Revision: 2 Effective Date: July 1, 2016
PJM Manual 07:: PJM Protection Standards Revision: 2 Effective Date: July 1, 2016 Prepared by System Planning Division Transmission Planning Department PJM 2016 Table of Contents Table of Contents Approval...6
PIPSPC. Prepared by Eng: Ahmed Safie Eldin. And. Introduction. Protection Control. Practical. System. Power
PIPSPC Practical Introduction Power System Protection Control Practical Introduction To Power System Protection And Control Prepared by Eng: Ahmed Safie Eldin 2005 Contents POWER SYSTEMS PRINCIPALS. 1
Transformer differential protection
Transformer differential protection Page 1 Issued June 1999 Changed since July 1998 Data subject to change without notice (SE970883) Features Three phase differential protection with two, three, five or
Substation applications
Substation applications To make it easy to choose the right for a protection application, the most typical applications are presented with the type of for them. Each sample application is presented by:
Tertiary Winding Design in wye-wye Connected Transformers Restricted Siemens Energy 2013 All rights reserved.
Pomona, CA, May 24 & 25, 2016 Tertiary Winding Design in wye-wye Connected Transformers Scope of Presentation > Tertiary vs. Stabilizing Winding? Tertiary vs. Stabilizing Winding? Need for Stabilizing
Sequence Networks p. 26 Sequence Network Connections and Voltages p. 27 Network Connections for Fault and General Unbalances p. 28 Sequence Network
Preface p. iii Introduction and General Philosophies p. 1 Introduction p. 1 Classification of Relays p. 1 Analog/Digital/Numerical p. 2 Protective Relaying Systems and Their Design p. 2 Design Criteria
CHAPTER 3 REVIEW OF POWER TRANSFORMER PROTECTION SCHEMES
CHAPTER 3 REVIEW OF POWER TRANSFORMER PROTECTION SCHEMES 3.1. Introduction Power Transformer is the nerve centre of any power distribution system. The capacity of power transformers is generally decided
Transformer Winding Design. The Design and Performance of Circular Disc, Helical and Layer Windings for Power Transformer Applications
The Design and Performance of Circular Disc, Helical and Layer Windings for Power Transformer Applications Minnesota Power Systems Conference November 3 5, 2009 Earl Brown Heritage Center University of
NERC Protection Coordination Webinar Series June 23, Phil Tatro
Power Plant and Transmission System Protection Coordination Volts Per Hertz (24), Undervoltage (27), Overvoltage (59), and Under/Overfrequency (81) Protection NERC Protection Coordination Webinar Series
Testing Numerical Transformer Differential Relays
Feature Testing Numerical Transformer Differential Relays Steve Turner Beckwith Electric Co., nc. ntroduction Numerical transformer differential relays require careful consideration as to how to test properly.
Basic Principles and Operation of Transformer
Basic Principles and Operation of Transformer CONSTRUCTIONAL ASPECTS Cores In order to enhance core s magnetic properties, it is constructed from an iron and silicon mixture (alloy). The magnetic core
System Protection and Control Subcommittee
Power Plant and Transmission System Protection Coordination Reverse Power (32), Negative Sequence Current (46), Inadvertent Energizing (50/27), Stator Ground Fault (59GN/27TH), Generator Differential (87G),
~=E.i!=h. Pre-certification Transformers
7 Transformers Section 26 of the electrical code governs the use and installations of transformers. A transformer is a static device used to transfer energy from one alternating current circuit to another.
Numbering System for Protective Devices, Control and Indication Devices for Power Systems
Appendix C Numbering System for Protective Devices, Control and Indication Devices for Power Systems C.1 APPLICATION OF PROTECTIVE RELAYS, CONTROL AND ALARM DEVICES FOR POWER SYSTEM CIRCUITS The requirements
7SG14 Duobias-M Transformer Protection
7SG14 Duobias-M Transformer Protection Document Release History This document is issue 2010/02. The list of revisions up to and including this issue is: Pre release Revision Date Change 2010/02 Document
16 Transformer and Transformer-feeder Protection
Chap16-254-279 17/06/02 9:58 Page 254 Transformer and Transformer-feeder Protection Introduction 16.1 Winding faults 16.2 Magnetising inrush 16.3 Transformer overheating 16.4 Transformer protection overview
Performance Analysis of Traditional and Improved Transformer Differential Protective Relays
Performance Analysis of Traditional and Improved Transformer Differential Protective Relays Armando Guzmán, Stan Zocholl, and Gabriel Benmouyal Schweitzer Engineering Laboratories, Inc. Hector J. Altuve
MILWAUKEE SCHOOL OF ENGINEERING LABORATORY SESSION 4 THREE PHASE TRANSFORMERS
LABORATORY SESSION 4 THREE PHASE TRANSFORMERS PURPOSE To investigate the three phase transformer connections and characteristics DISCUSSION Most electrical energy is generated and transmitted using three
Power systems Protection course
Al-Balqa Applied University Power systems Protection course Department of Electrical Energy Engineering 1 Part 5 Relays 2 3 Relay Is a device which receive a signal from the power system thought CT and
www. ElectricalPartManuals. com Generator Differential Relay MD32G Rotating Machine Differential Relay
Generator Differential Relay The MD3G Rotating Machine Differential Relay is a member of Cooper Power Systems Edison line of microprocessor based protective relays. The MD3G relay offers the following
Back to the Basics Current Transformer (CT) Testing
Back to the Basics Current Transformer (CT) Testing As test equipment becomes more sophisticated with better features and accuracy, we risk turning our field personnel into test set operators instead of
Impact of transient saturation of Current Transformer during cyclic operations Analysis and Diagnosis
1 Impact of transient saturation of Current Transformer during cyclic operations Analysis and Diagnosis BK Pandey, DGM(OS-Elect) Venkateswara Rao Bitra, Manager (EMD Simhadri) 1.0 Introduction: Current
OPEN-PHASE DETECTION TECHNIQUES FOR CRITICAL STANDBY SUPPLIES
OPEN-PHASE DETECTION TECHNIQUES FOR CRITICAL STANDBY SUPPLIES U AJMAL, GE Grid Solutions UK Ltd, usman.ajmal@ge.com S SUBRAMANIAN, GE Grid Solutions UK Ltd, sankara.subramanian@ge.com H Ha GE Grid Solutions
PD300. Transformer, generator and motor protection Data sheet
PD300 Transformer, generator and motor protection Data sheet DSE_PD300_eng_AO No part of this publication may be reproduced by whatever means without the prior written permission of Ingeteam T&D. One of
O V E R V I E W O F T H E
A CABLE Technicians TESTING Approach to Generator STANDARDS: Protection O V E R V I E W O F T H E 1 Moderator n Ron Spataro AVO Training Institute Marketing Manager 2 Q&A n Send us your questions and comments
KNOW MORE ABOUT THE TRANSFORMERS. Glossary Transformers
KNOW MORE ABOUT THE TRANSFORMERS Glossary Transformers Ambient temperature The existing temperature of the atmosphere surrounding a transformer installation. Ampere The practical unit of electric current.
Type KLF Generator Field Protection-Loss of Field Relay
Supersedes DB 41-745B pages 1-4, dated June, 1989 Mailed to: E, D, C/41-700A ABB Power T&D Company Inc. Relay Division Coral Springs, FL Allentown, PA For Use With Delta Connected Potential Transformers
Transformer Protection
1 Presenter Contact Info Wayne Hartmann Senior VP, Customer Excellence Beckwith Electric Company whartmann@beckwithelectric.com 904 238 3844 Wayne is the top strategist for delivering innovative technology
889 Advanced Generator Protection Technical Note
GE Grid Solutions 8 Series 889 Advanced Generator Protection Technical Note GE Publication Number: GET-20056 Copyright 2017 GE Multilin Inc. Overview The Multilin 889 is part of the 8 Series platform that
POWER TRANSFORMER PROTECTION USING ANN, FUZZY SYSTEM AND CLARKE S TRANSFORM
POWER TRANSFORMER PROTECTION USING ANN, FUZZY SYSTEM AND CLARKE S TRANSFORM 1 VIJAY KUMAR SAHU, 2 ANIL P. VAIDYA 1,2 Pg Student, Professor E-mail: 1 vijay25051991@gmail.com, 2 anil.vaidya@walchandsangli.ac.in
ENOSERV 2014 Relay & Protection Training Conference Course Descriptions
ENOSERV 2014 Relay & Protection Training Conference Course Descriptions Day 1 Generation Protection/Motor Bus Transfer Generator Protection: 4 hours This session highlights MV generator protection and
EASUN REYROLLE LIMITED
OCTOBER 2003 APPLICATION AND COMMISSIONING MANUAL FOR NUMERICAL BIASED DIFFERENTIAL PROTECTION RELAY TYPE - MIB202 EASUN REYROLLE LIMITED 1 ISSUE NO : 1 st Issue DATE OF ISSUE : 01-10 - 2003 DEPARTMENT
Power Station Electrical Protection A 2 B 2 C 2 Neutral C.T E M L } a 2 b 2 c 2 M M M CT Restricted E/F Relay L L L TO TRIP CIRCUIT Contents 1 The Need for Protection 2 1.1 Types of Faults............................
How to maximize reliability using an alternative distribution system for critical loads
White Paper WP024001EN How to maximize reliability using an alternative distribution system for critical loads Executive summary The electric power industry has several different distribution topologies
GENERATOR INTERCONNECTION APPLICATION Category 5 For All Projects with Aggregate Generator Output of More Than 2 MW
GENERATOR INTERCONNECTION APPLICATION Category 5 For All Projects with Aggregate Generator Output of More Than 2 MW ELECTRIC UTILITY CONTACT INFORMATION Consumers Energy Interconnection Coordinator 1945
Stabilized Differential Relay SPAD 346. Product Guide
Issued: July 1998 Status: Updated Version: D/21.03.2006 Data subject to change without notice Features Integrated three-phase differential relay, three-phase overcurrent relay and multiconfigurable earth-fault
Power systems 2: Transformation
Power systems 2: Transformation Introduction In this series of articles, we will be looking at each of the main stages of the electrical power system in turn. s you will recall from our Introduction to
TECHNICAL BULLETIN 004a Ferroresonance
May 29, 2002 TECHNICAL BULLETIN 004a Ferroresonance Abstract - This paper describes the phenomenon of ferroresonance, the conditions under which it may appear in electric power systems, and some techniques
thepower to protect the power to protect i-gard LITERATURE Low and medium voltage
thepower to protect i-gard LITERATURE Low and medium voltage distribution systems Arc Flash Hazards and High Resistance Grounding Grounding of Standby and Emergency Power Systems Neutral Grounding Resistors
IMPROVEMENTS IN PROTECTION AND COMMISSIONING OF DIGITAL TRANSFORMER RELAYS AT MEDIUM VOLTAGE INDUSTRIAL FACILITIES
IMPOVEMENTS IN POTECTION AND COMMISSIONING OF DIGITAL TANSFOME ELAYS AT MEDIUM VOLTAGE INDUSTIAL FACILITIES Copyright Material IEEE Paper No. PCIC-AN84 Charles J. Mozina, P.E. Life Fellow Member, IEEE
MONITORING OF DISTRIBUTION TRANSFORMER PARAMETERS USING PLC
MONITORING OF DISTRIBUTION TRANSFORMER PARAMETERS USING PLC Shubhangi Landge¹, Snehal Waydande², Sanjay Sangale³, Somesh Gaikwad⁴ ¹Assistant Professor, Dept. Of Electrical Engineering, AISSMS IOIT College,
Protection Basics Presented by John S. Levine, P.E. Levine Lectronics and Lectric, Inc GE Consumer & Industrial Multilin
Protection Basics Presented by John S. Levine, P.E. Levine Lectronics and Lectric, Inc. 770 565-1556 John@L-3.com 1 Protection Fundamentals By John Levine 2 Introductions Tools Outline Enervista Launchpad
Differential Protection Optimal differential protection for phase shifter transformers and special transformers
Differential Protection Optimal differential protection for phase shifter transformers and special transformers Due to the energy transition, a demand for renewable energy sources integration into power
Generator Advanced Concepts
Generator Advanced Concepts Common Topics, The Practical Side Machine Output Voltage Equation Pitch Harmonics Circulating Currents when Paralleling Reactances and Time Constants Three Generator Curves
Utility Interconnection and System Protection
Utility Interconnection and System Protection Alex Steselboim President, Advanced Power Technologies, Inc. Utility paralleling vs. isolated operation. Isochronous kw load sharing Reactive power (VAR) sharing
Transformer differential protection RADSB
protection RADSB User s Guide 1MRK 504 002-UEN Replaces 1MDU04007-EN Features Three-phase differential protection with two, three, five or six through-current restraint inputs Complete phase and earth-fault
The InterNational Electrical Testing Association Journal. BY STEVE TURNER, Beckwith Electric Company, Inc.
The InterNational Electrical Testing Association Journal FEATURE PROTECTION GUIDE 64S Theory, Application, and Commissioning of Generator 100 Percent Stator Ground Fault Protection Using Low Frequency
HPS Universal BUCK-BOOST TRANSFORMERS
BUCK-BOOST TRANSFORMERS Single and Three Phase Potted Buck-Boost Transformers Buck-Boost Applications & Standard Specification... 80 Selecting Buck-Boost Transformers... 81 Single Phase Selection Tables...
Protecting Large Machines for Arcing Faults
Protecting Large Machines for Arcing Faults March 2, 2010 INTRODUCTION Arcing faults occur due to dirty insulators or broken strands in the stator windings. Such faults if undetected can lead to overheating
BE1-67N GROUND DIRECTIONAL OVERCURRENT RELAY FEATURES ADDITIONAL INFORMATION. FUNCTIONS AND FEATURES Pages 2-4. APPLICATIONS Page 2
BE1-67N GROUND DIRECTIONAL OVERCURRENT RELAY The BE1-67N Ground Directional Overcurrent Relay provides ground fault protection for transmission and distribution lines by sensing the direction and magnitude
Data. Dr Murari Mohan Saha ABB AB. KTH/EH2740 Lecture 3. Data Acquisition Block. Logic. Measurement. S/H and A/D Converter. signal conditioner
Digital Protective Relay Dr Murari Mohan Saha ABB AB KTH/EH2740 Lecture 3 Introduction to Modern Power System Protection A digital protective relay is an industrial microprocessor system operating in real
BUS2000 Busbar Differential Protection System
BUS2000 Busbar Differential Protection System Differential overcurrent system with percentage restraint protection 1 Typical Busbar Arrangements Single Busbar Double Busbar with Coupler Breaker and a Half
Bus Protection Fundamentals
Bus Protection Fundamentals Terrence Smith GE Grid Solutions 2017 Texas A&M Protective Relay Conference Bus Protection Requirements High bus fault currents due to large number of circuits connected: CT
Preventing transformer saturation in static transfer switches A Real Time Flux Control Method
W H I T E PA P E R Preventing transformer saturation in static transfer switches A Real Time Flux Control Method TM 2 SUPERSWITCH 4 WITH REAL TIME FLUX CONTROL TM Preventing transformer saturation in static
Differential Protection with REF 542plus Feeder Terminal
Differential Protection with REF 542plus Application and Setting Guide kansikuva_bw 1MRS 756281 Issued: 09.01.2007 Version: A Differential Protection with REF 542plus Application and Setting Guide Contents:
Motor Protection. May 31, Tom Ernst GE Grid Solutions
Motor Protection May 31, 2017 Tom Ernst GE Grid Solutions Motor Relay Zone of Protection -Electrical Faults -Abnormal Conditions -Thermal Overloads -Mechanical Failure 2 Setting of the motor protection
Embedded Generation Connection Application Form
Embedded Generation Connection Application Form This Application Form provides information required for an initial assessment of the Embedded Generation project. All applicable sections must be completed
CHAPTER 4. Distribution Transformers
CHAPTER 4 Distribution Transformers Introduction A transformer is an electrical device that transfers energy from one circuit to another purely by magnetic coupling. Relative motion of the parts of the
2015 Relay School Bus Protection Mike Kockott March, 2015
2015 Relay School Bus Protection Mike Kockott March, 2015 History of Bus Protection Circulating current differential (1900s) High impedance differential (1940s) Percentage restrained differential (1960s)
Busbars and lines are important elements
CHAPTER CHAPTER 23 Protection of Busbars and Lines 23.1 Busbar Protection 23.2 Protection of Lines 23.3 Time-Graded Overcurrent Protection 23.4 Differential Pilot-Wire Protection 23.5 Distance Protection
Demagnetization of Power Transformers Following a DC Resistance Testing
Demagnetization of Power Transformers Following a DC Resistance Testing Dr.ing. Raka Levi DV Power, Sweden Abstract This paper discusses several methods for removal of remanent magnetism from power transformers.
Improved power transformer protection using numerical relays
Improved power transformer protection using numerical relays Bogdan Kasztenny* and Mladen Kezunovic Texas A&M University, USA Large power transformers belong to a class of very expensive and vital components
Power System Fundamentals
Power System Fundamentals Relay Applications PJM State & Member Training Dept. Objectives At the end of this presentation the Student will be able to: Describe the purpose of protective relays Identify
Analyzing the Impact of Shunt Reactor Switching Operations Based on DFR Monitoring System
Analyzing the Impact of Shunt Reactor Switching Operations Based on DFR Monitoring System Lalit Ghatpande, SynchroGrid, College Station, Texas, 77840 Naveen Ganta, SynchroGrid, College Station, Texas,
DATA SHEET FOR LIGHTING TRANSFORMER APPD. BY VDV PROJECT NO
PART - A : SPECIFIC REQUIREMENTS THIS DATA SHEET IS APPLICABLE FOR IN BOILER A CLIMATIC CONDITIONS PACKAGE 1 DESIGN AMBIENT TEMPERATURE 45 C 2 ALTITUDE ( ABOVE MSL ) 6.71 MTRS. 3 RELATIVE HUMIDITY 74 %
Pinhook 500kV Transformer Neutral CT Saturation
Russell W. Patterson Tennessee Valley Authority Presented to the 9th Annual Fault and Disturbance Analysis Conference May 1-2, 26 Abstract This paper discusses the saturation of a 5kV neutral CT upon energization
This webinar brought to you by The Relion Product Family Next Generation Protection and Control IEDs from ABB
This webinar brought to you by The Relion Product Family Next Generation Protection and Control IEDs from ABB Relion. Thinking beyond the box. Designed to seamlessly consolidate functions, Relion relays
STRAY FLUX AND ITS INFLUENCE ON PROTECTION RELAYS
1 STRAY FLUX AND ITS INFLUENCE ON PROTECTION RELAYS Z. GAJIĆ S. HOLST D. BONMANN D. BAARS ABB AB, SA Products ABB AB, SA Products ABB AG, Transformers ELEQ bv Sweden Sweden Germany Netherlands zoran.gajic@se.abb.com
Embedded Generation Connection Application Form
Embedded Generation Connection Application Form This Application Form provides information required for an initial assessment of the Embedded Generation project. All applicable sections must be completed
Current Transformer Requirements for VA TECH Reyrolle ACP Relays. PREPARED BY:- A Allen... APPROVED :- B Watson...
TECHNICAL REPORT APPLICATION GUIDE TITLE: Current Transformer Requirements for VA TECH Reyrolle ACP Relays PREPARED BY:- A Allen... APPROVED :- B Watson... REPORT NO:- 990/TIR/005/02 DATE :- 24 Jan 2000
Overcurrent and Overload Protection of AC Machines and Power Transformers
Exercise 2 Overcurrent and Overload Protection of AC Machines and Power Transformers EXERCISE OBJECTIVE When you have completed this exercise, you will understand the relationship between the power rating
Power Plant and Transmission System Protection Coordination Fundamentals
Power Plant and Transmission System Protection Coordination Fundamentals NERC Protection Coordination Webinar Series June 2, 2010 Jon Gardell Agenda 2 Objective Introduction to Protection Generator and
TesTIng of Power. Transformers are the largest, most. feature. By brandon dupuis
feature By brandon dupuis An Introduction to Electrical diagnostic TesTIng of Power Transformers 38 Transformers are the largest, most expensive, and highly critical components of most utility substations.
NERC Protection Coordination Webinar Series July 15, Jon Gardell
Power Plant and Transmission System Protection Coordination Reverse Power (32), Negative Sequence Current (46), Inadvertent Energizing (50/27), Stator Ground Fault (59GN/27TH), Generator Differential (87G),
Unit 3 Magnetism...21 Introduction The Natural Magnet Magnetic Polarities Magnetic Compass...21
Chapter 1 Electrical Fundamentals Unit 1 Matter...3 Introduction...3 1.1 Matter...3 1.2 Atomic Theory...3 1.3 Law of Electrical Charges...4 1.4 Law of Atomic Charges...4 Negative Atomic Charge...4 Positive
Short-Circuit Current Calculations
Basic Point-to-Point Calculation Procedure Step. Determine the transformer full load amps (F.L.A.) from either the nameplate, the following formulas or Table : Multiplier = 00 *% Z transformer Step 2.
Impact Assessment Generator Form
Impact Assessment Generator Form This connection impact assessment form provides information for the Connection Assessment and Connection Cost Estimate. Date: (dd/mm/yyyy) Consultant/Developer Name: Project
Earth Fault Protection
Earth Fault Protection Course No: E03-038 Credit: 3 PDH Velimir Lackovic, Char. Eng. Continuing Education and Development, Inc. 9 Greyridge Farm Court Stony Point, NY 10980 P: (877) 322-5800 F: (877) 322-4774
This document covers common questions concerning the design of an effectively grounded system.
This document covers common questions concerning the design of an effectively grounded system. To prevent against temporary overvoltage conditions when a line-to-ground fault occurs on the power grid.