Attention High Voltage, Double / Reinforced NOT CE Mark Risk of Danger, Risk of Insulation Litter TECHNICAL SPECIFICATION

Transcription

1 DS0 RE U/DOWN COUNTER Attention Hig Voltage, Double / Reinforced NOT CE Mark Rik of Danger, Rik of Inulation Litter Warning Electric Sock TECHNICAL SECIFICATION Dimenion : 8x8mm anel Cut-out : 5,5x5,5mm : x Digit 7 Segment Count ut : x (Max:7500 Hz, 5-30V) ut : 0m (min), oitive input (N only) (5..30V) put : ; Relay (O-NO-NC), 50VAC, A, Reitive load open collector (NN), 30V, 00mA max. Senor type : N/NN proximity witc - NN/N/Totem-pole output encoder ut frequency : 0, 500, 500, 7500Hz electable NN Selection : Connect npn elect to V to elect NN enor for and. input i alway N. For totem pole or N type enor npn elect left unconnected. Senor Supply : VDC, 50mA max. (unregulated) Supply Voltage : 00..0VAC, 50-60Hz or Vac/dc (optional) ower Conumption : < 6VA Humidity : 80% up to 30 o C, ten linearly decreae to 50% at 50 o C (non-condening) Altitude : < 000 m EMC : EN , EN (Only ligt indutrial environment) Safety : EN 600-; ollution degree, meaurement category I, (Only ligt indutrial environment, double/reinforced iolated, non-conductive pollution environment) rotection Cla : I0; according to EN 6059 Storage Temperature : -0 o C.. 60 o C (no icing) Operation Temp. : o C Weigt : < 0.5 kg Key : Micro witc Torque for crewing : Max. 0.5 N.m no: normally open nc: normally cloed (*) Connect SS return pin directly to GNG Tel: , Fax: (**) Ue freeweeling diode to protect SS (***) To elect NN option; connect npn elect to V. 9 V 50mA 9 V 50mA 0 C.. ut Sayma (ör:yukarı) 0 C.. ut C.. ut C.. ut Sayma In (ör:aşağı) In 3 SS 3 SS Gnd Switc Gnd 9 V 50mA 0 C.. ut C.. ut In 3 SS Gnd - (*) - Totem-ole Encoder Switc (**) N/NN roximity Switc (***) N/NN roximity Switc (***) Switc 30Vdc (Max)

2 INSTALLATION, USE and WARNINGS Ti device and it packing i NOT litter and may NOT be dipoed of wit dometic wate. leae return ti device and it packing to an appropriate recycling point at te end of it ervice life. leae read ti uer manual carefully and completely before intallation and ue. leae take into conideration all warning mentioned in ti manual. DS0 i uitable only for permanent panel type mounting Intallation and ue of ti device mut be done by qualified, autorized and trained tecnical peronnel only. Inpect device carefully before intallation. Do not intall and ue broken and defective device. Do not diaemble device. Do not make any repair on any part of te device. Tere i no acceible part inide te device. leae contact to manufacturer for broken and defective device. Do not ue device in environment ubject to flammable, exploive and corroive gae and/or ubtance. Ti device i deigned for application only in ligt indutrial environment. Ti device i not uitable for medical and reidential ue. Ti device i not uitable for ue related wit uman ealt and afety. Ti device i not uitable for automotive, military and marine ue. Do not allow cildren and unautorized people to ue ti device. Before intallation and any tecnical work, diconnect te power upply and main connection. Ceck te power upply voltage level before power on, and make ure voltage level i in pecified limit. Ceck quality of neutral line. Improper neutral line may give permanent damage to te device. Connect an external power witc and an external fue (A, 50VAC) to te power upply line tat are eaily acceible for rapid intervention. Connect an external fue (A, 50VAC) for eac relay output eparately. Ue appropriate cable for power upply and main connection. Apply afety regulation during intallation. Intall te device in a well ventilated place. Intall te device permanently into a proper panel cut-out. Fix te device wit two fatener upplied wit te device. Only front panel mut be acceible after intallation i completed. Do not operate te device oter ten te environmental condition given in Tecnical Specification. Do not operate te device in environment tat may caue conductive pollution. Take precaution againt negative environmental condition like umidity, vibration, pollution and ig/low temperature during intallation. Keep device, ignal cable and communication cable away from circuit breaker, power cable and device/cable emitting electrical noie. Ue ielded and twited ignal and communication cable and connect ield to eart ground on device ide. Keep lengt of ignal and communication cable le tan 3m. refer to ue (t) option for encoder, elect (Freq0) to count mecanical witc ON-OFF pule, elect te minimum input frequency option tat uit your application. For tu, d, ; input ignal frequency all be at mot / of te elected input frequency option if bot input are ued. And for t; input ignal frequency all be at mot / of te elected input frequency option if bot input are ued. In your application, alway ue eparate and independent mecanical and/or electromecanical device/apparatu to upport DS0 to andle emergency cae.. Ue inulated cable end-leeve at te end of cable crewed to te device connector terminal. Maximum torque for crewing; 0.5 N.m. leae ceck for latet device and documentation update regularly. All update and all information are ubject to cange witout notice. GENERAL SECIFICATION Ti device i deigned for baic control application only in ligt indutrial environment. x Digit, ingle RE, ingle OUT, up/down counter Count witc, proximity witc & incremental encoder input aword protection, Selectable input frequency, Calibration contant; Selectable decimal point; Digit, 7 input / 9 output function option, Add OFF to Count Value OUT; latc or econd pule Load Count value & OUT tatu at te latet power failure after te firt power on RE via front panel EEROM memory to tore etting Dimenion: 8x8mm, Eay connection wit plug-in connector Tel: , Fax:

3 FRONT ANEL RE re for ec. ROGRAMMĐNG RE VALUE re for ec. Upper rst Enter value (*) rog. end (*) Decimal point appear at dec.nt. election INUT TYES n u G d Cr.dr drct Cr.dr oppo n n n n- N / Totem ole ON NN OFF N / Totem ole OFF NN ON CLAEANING Do not ue any olvent (alcool, tinner, benzine, acid, etc.) or corroive ubtance to clean te device. Ue only a dry and clean non-abraive clot. Before cleaning, diconnect te power upply and main connection. Tel: , Fax:

4 ROGRAMMING ARAMETERS re for ec. Upper CodE Enter 6 Enter fixed paword; ON duration For latcing enter, CALb Calibration contant Int.n,.u,.G,.d,.,.,. ConF 0..8 dec. 0, 0.0, 0.00, ut option Operating mode option Select place of decimal point Factory Value: St: 000 : 00.0 ec. CALb:.000 Int:.n ConF: 0 dec.: 0 Cr.dr: drct Freq: 0 on.r: YES offs: 0000 Cr.dr drct, oo Counting direction; direct / oppoite or up / down Freq 0, 500, 500, 7500 Hz Max. frequncy for input ignal. Select 0Hz for mecanical witc. on.r YES, no Ye: after power-on. No: Load te count value & put tatu at te latet power failure after te firt power-on. offs Value;. If Cr.drdrCt; Counter i et to offs wit RE ON or panel reet.. If Cr.droo; wen 0..6 and t.u,.g,., OUT i ON, a oon a counter reace offs. (*) rog. end (*) Decimal appear at dec.nt election. Note: If no entry i done for 0 ec. during programming, current entrie are accepted and aved to EEROM memory. Tel: , Fax:

5 OERATING MODES t u, G, Cr.dr drct t u, G, Cr.dr oppo t n, d,, Comment 0 Counting continue up/down until RE ON after i reaced. Counting top until RE ON after i reaced. Counting continue up/down until RE ON after i reaced. 3 Counter i reet after i reaced. Counting continue up/down after i reaced. Counter i reet wit OUT pule OFF. 5 Counting top after i reaced. Counter i reet OUT pule OFF. 6 Counter i reet after i reaced but diplay freeze until te end of OUT pule. 7 OUT i ON wen counter i equal to ele OFF. Ue SS out if ON duration i too mall for relay ON time. 8 OUT i ON wen counter i greater or equal to ele OFF. Ue NC pin of OUT if le ten i required ule Latced put Tel: , Fax: