Information. Mechanically Jointed Rodless Cylinder Series MY2H/MY2HT. -XB20: Stroke adjusting unit with adjusting bolt specifications

Transcription

1 Information MC Corporation Akiabara UDX 1F, -1-1, otokanda, Ciyoda-ku, Tokyo , JAPAN UR ttp:// MC Corporation All rigts reserved. 07-U-UK Issued: August, 2007 D-K P-1300(K) Mecanically Jointed Rodless Cylinder eries /T -XB20: wit adjusting bolt specifications ock absorber troke adjustment range for adjusting bolt mm : One linear guide ø, ø2, ø T: Two linear guides ø, ø2, ø 1

2 eries /T How to Order (Refer to Best Pneumatics for specifications details.) inear Guide Type MY2 H G 300 M9B XB20 H HT Guide type One linear guide Two linear guides 2 mm 2 mm mm wit adjusting bolt specifications Number of auto switces n 2 pcs. 1 pc. n pcs. ymbol TN TF G Type M tread Rc NPT G Tread type ø ø2, ø Piping Centralised piping type (tandard) Auto switces itout auto switc (built-in magnet) Note) For te applicable auto switc model, refer to table below. position Bot ends One end Note) is applicable for stroke adjusting units and H. 2, tandard stroke Note) 0, 100,10, 200, 20, 300, 30, 0,, 00, 0, 600 troke Maximum available stroke Note) trokes can be manufactured in 1 mm increments, up to te maximum stroke. However, add -XB10 to te end of te model number for nonstandard strokes from 1 to 99. Also wen exceeding a 600 mm stroke, specify -XB11 at te end of te model number. Refer to Made to Order pecifications (Best Pneumatics). H H ock absorbers for and s Model T itout adjusting unit it low load sock absorber it ig load sock absorber it one and one eac Unit type RB0806 RB1007 RB1007 RB112 2 RB1007 RB112 RB112 RB201 RB112 RB201 RB201 RB272 Applicable Auto witc / Refer to Best Pneumatics for detailed specifications about an auto switc itself. Type Reed switc olid state switc pecial function Diagnostic indication (2-colour indication) lectrical entry Grommet Grommet Indicator ligt 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN) 3-wire (PNP) 2-wire 3-wire (NPN equiv.) 2 V No 2-wire 2 V Note 1) ead wire lengt symbols: 0. m (xample: M9N) 1 m M (xample: M9NM) 3 m (xample: M9N) m Z (xample: M9NZ) Yes Yes iring (Output) oad voltage DC V, 12 V 12 V V, 12 V 12 V V 12 V AC 100 V 100 V or less Auto switc model Perpendicular M9NV M9PV M9BV M9NV M9PV M9BV A96V A93V A90V In-line M9N M9P M9B M9N M9P M9B A96 A93 A90 ead wire lengt (m) 0. () 1 (M) 3 () (Z) Pre-wire connector Applicable load IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC Note 2) ince tere are oter applicable auto switces tan te ones listed above, refer to Best Pneumatics for details. Note 3) For details about auto switces wit pre-wire connector, refer to Best Pneumatics. Note ) Auto switc is sipped togeter not assembled. Note ) olid state switc marked are produced upon receipt of order. 2

3 troke Adjusting Unit wit Adjusting Bolt pecifications eries /T wit adjusting bolt model (order number for unit itself) T eft Rigt eft Rigt eft Rigt eft Rigt Model Unit type -A1-XB20 -A2-XB20 -AH1-XB20 -AH2-XB20 T-A1-XB20 T-A2-XB20 T-AH1-XB20 T-AH2-XB20 Note) wit adjusting bolt (-XB20) cannot be mounted wit te standard cylinder. 2 -A21-XB20 -A22-XB20 -A2H1-XB20 -A2H2-XB20 T-A21-XB20 T-A22-XB20 T-A2H1-XB20 T-A2H2-XB20 -A1-XB20 -A2-XB20 -AH1-XB20 -AH2-XB20 T-A1-XB20 T-A2-XB20 T-AH1-XB20 T-AH2-XB20 Cylinder body (left) (rigt) Caution <troke adjustment using te adjusting bolt> q oosen adjusting bolt lock nut and adjust te stroke by rotating te adjusting bolt. Ten, fix te adjusting bolt by tigtening te lock nut. en te effective stroke of te sock absorber decreases as a result of stroke adjustment, te absorption capacity becomes extremely small. ecure te sock absorber in a position were it retracts approximately 0. mm from te adjusting bolt, and, uniformly tigten eac sock absorber olding bolt wit te same torque. olding bolt ock absorber olding bolt olding bolt ock absorber olding bolt lock nut ock absorber lock nut ock absorber (-XB20) T (-XB20) olding bolt tigtening torque N m T ock absorber olding bolt tigtening torque N m T 1..0 ock absorber 0. w en te sock absorber is used witin te air cusion stroke range, te cylinder may not operate smootly due to bouncing depending on te degree te cusion adjustment part opens. Be careful and avoid over-tigtening te cusion needle. 3

4 eries /T Dimensions (Refer to te Best Pneumatics for oter dimensions) Unit Unit: mm (Absorber stroke) T D ock Absorber Applicable cylinder T D (MAX. 9.8) (MAX..) 6 (MAX. 22) ock absorber type RB0806 M x 0.8 x 2 RB1007 M8 x 1.0 x 3 RB112 M10 x 1.0 x 0 Adjustment range H Unit (Absorber stroke) T D ock Absorber Applicable cylinder D T (MAX. 9.8) (MAX..) 6 (MAX. 22) ock absorber type RB1007 RB112 RB201 M x 0.8 x 2 M8 x 1.0 x 3 M10 x 1.0 x 0 Adjustment range.6 11.

5 troke Adjusting Unit wit Adjusting Bolt pecifications eries /T Dimensions (Refer to te Best Pneumatics for oter dimensions) T Unit Unit: mm (Absorber stroke) T D ock Absorber B Applicable cylinder T T2 T B D T (MAX. 9.8) (MAX..) 6 (MAX. 22) ock absorber type RB1007 M x 0.8 x 2 RB112 M8 x 1.0 x 3 RB201 M10 x 1.0 x 0 Adjustment range T H Unit (Absorber stroke) T D ock Absorber B Applicable cylinder T T2 T B D T (MAX. 9.8) (MAX..) 6 (MAX. 22) ock absorber type RB112 M x 0.8 x 2 RB201 M8 x 1.0 x 3 RB272 M10 x 1.0 x 0 Adjustment range.6 11.

6 eries /T Holder Mounting Bracket for XB20, s are used to fasten te stroke adjusting unit wit te adjusting bolt (-XB20) at an intermediate stroke position. -X -X17 MY2 troke Auto switc ymbol XB20 X q Refer to table below for te combination description. erefer to table below for te combination description. troke Note) Indicates te stroke prior to mounting te stroke adjusting unit. wrefer to table below for te combination description. eries/ H One linear guide HT Two linear guides 2 q, H,, H, H H, H,, H, H H w Holder mounting bracket X X17 e Combination symbol Z H Z HZ H Mounting pcs. X X Combination description X on one side X on bot sides X on one side, X17 on te oter side X on side X on side X on side, X17 on te oter side X on side, X17 on te oter side X17 on one side X17 on bot sides X17 on side X17 on side (-XB20) T (-XB20) pacer lengt l pacer lengt l Place te protruding section on te stroke adjusting unit side. 6

7 troke Adjusting Unit wit Adjusting Bolt pecifications eries /T xamples of Made to Order: Holder Mounting Bracket for XB20, s wit one eac of X and X17 2G-300-XB20XZ X X17 wit older mounting bracket (rigt) -A22-XB20X ( for 2 and X bracket) only (rigt) -A22-XB20XN (2, X bracket for ) (-XB20) T (-XB20) X17 and s, were X17 is mounted on only and noting on. 2G-300H-XB20X17 Note) For, te parts are packed togeter wen sipped. How to order single pieces of stroke adjusting unit wit adjusting bolt and older mounting bracket -A1-XB20 T-A1-XB20 X17 Combination symbol N + only X 1 X17 2 wit adjusting bolt 7

8 MC CORPORATION (urope) Austria Belgium +32 (0) Bulgaria office@smc.bg Croatia office@smc.r Czec Republic office@smc.cz Denmark smc@smc-pneumatik.dk stonia smc@smcpneumatics.ee Finland smcfi@smc.fi France +33 (0) contact@smc-france.fr Germany +9 (0) info@smc-pneumatik.de Greece sales@smcellas.gr Hungary office@smc.u Ireland +33 (0) sales@smcpneumatics.ie Italy +39 (0) mailbox@smcitalia.it atvia +1 (0) info@smclv.lv ituania Neterlands +31 (0) info@smcpneumatics.nl Norway post@smc-norge.no Poland office@smc.pl Portugal postpt@smc.smces.es Romania smcromania@smcromania.ro Russia marketing@smc-pneumatik.ru lovakia office@smc.sk lovenia office@smc.si pain post@smc.smces.es weden +6 (0) post@smcpneumatics.se witzerland +1 (0) info@smc.c Turkey +90 (0) smc@entek.com.tr UK + (0) sales@smcpneumatics.co.uk uropean Marketing Centre MC CORPORATION MC CORPORATION Akiabara UDX 1F, -1-1, otokanda, Ciyoda-ku, Tokyo , JAPAN Pone: X: st printing MP printing MP 00 Printed in pain pecifications are subject to cange witout prior notice and any obligation on te part of te manufacturer.