Schematics. Part B, Section 4. This section covers the following unit congifurations. Model 3500 Voltage 1 Pump Piston (E, F or G) 6-Port (B or C)

Transcription

1 Part B, Section This section covers the following unit congifurations. Model 00 Voltage Pump Piston (E, F or G) Manifold Control -Port (A) -Port (B or C) UniScan 000 Nordson Corporation -000 Issued /00 BEN-0-[U-SCHEM]-

2 B -0 BEN-0-[U-SCHEM] Issued / Nordson Corporation

3 B - Section B. Introduction The wiring diagrams contained in this section are based on the voltage code of your unit. Refer to the following table to determine the voltage code of your unit; then refer to the appropriate wiring diagram in this section. Unit Voltage Code Table B - Unit Voltage Codes and Applicable Wiring Diagrams Specification Type of service you can connect to the unit: (See Note A) Part of this section to refer to: /PE 00 0 V 00 0 VAC (two-wire service without a neutral) Voltage Code Wiring Diagram 00 0 VAC (three-wire service without a neutral) NOTE A: This specification is printed in the VOLTS (ac) portion of the identification plate on your unit.. Use of Wiring Diagrams Each wiring diagram is contained on two facing pages. Sometimes a wire shown on one page is connected to terminals or components shown on the facing page. In these cases, the connecting wiring is labeled on each page with the same letters. For example, if you want to trace a wire or harness labeled BL on the left page, look for a wire or harness labeled BL on the right page. Each wiring diagram shows all of the options or special features the unit can be equipped with. Options and special features are indicated by dotted lines. To determine the features and options of your unit, refer to Explanation of Configuration Code at the end of the Description section. 000 Nordson Corporation -000 Issued /00 BEN-0-[U-SCHEM]-

4 B -. Voltage Code This schematic applies to voltage code melters. Refer to Table B - to determine the voltage code of your melter. TB N L L L B A NOTE: FOR SINGLE PHASE USE, CUSTOMER TO SUPPLY A SINGLE PHASE JUMPER CONNECTED FROM TB A TO TB B. JUMPER WIRE TO BE 0 GAUGE WIRE * * THIS BOX REPRESENTS THE LINE FILTER AND THE SCHEMATIC IS SHOWN IN DETAIL H. (OPTIONAL ON UNISCAN R AND MULTISCAN R UNITS) 7A AUX NOTE: WIRE NO. C REQUIRED ONLY WITH IZUMI BREAKER. CB C SEE DETAIL B P. A J J A PCB C SEE DETAIL A P. J J J A PCB SEE DETAIL A P. D J J J B PCB7 J J J J J 7 F ASHUTDOWN (DELAY) J F A FAULT READY MAIN CONTROL BOARD MICROSET (R) UNISCAN (R) PCB J TANK OVERTEMPERATURE 7 THERMOSTAT COR 0 7 N N N ALARM READY ON RED GREEN WHITE SOL SEE NOTE TB LOW LEVEL SWITCH (OPTIONAL) G L L L C C C C NOTES:.DETAILS SHOWN FOR REFEREE ONLY AND SHOULD NOT BE INTERPRETED LITERALLY..CONNECTIONS SHOWN FOR SOLENOID ARE FOR PISTON PUMP WITHOUT RUN UP. TB C C (OPTIONAL) DETAIL H LINE FILTER ASSEMBLY 07/ Fig. B - Schematic for 00 Voltage Code Melters ( of ) BEN-0-[U-SCHEM] Issued / Nordson Corporation

5 B - TANK HEATER NOTES:.DETAILS SHOWN FOR REFEREE ONLY AND SHOULD NOT BE INTERPRETED LITERALLY. Fig. B - Schematic for 00 Voltage Code Melters ( of ) 07/ 000 Nordson Corporation -000 Issued /00 BEN-0-[U-SCHEM]-

6 B -. Voltage Code Wiring Diagram This wiring diagram applies to voltage code melters. Refer to Table B - to determine the voltage code of your melter. SOL SW J J TB GND C A X X A B C G SLIDE BASE GND STUD J PCB MAIN CONTROL BOARD MICROSET(R) UNISCAN (R) J SEE DETAIL C G G INSTALL WIRES G & G WITH /R OPTION C B A D N N N A D B C B A 7 0 7B 7A C E B N POWER ON (WHITE) N UNIT READY (GREEN) N FAULT (RED) DETAIL C PCB J 070/ Fig. B - Wiring Diagram for 00 Voltage Code Melters ( of ) BEN-0-[U-SCHEM] Issued / Nordson Corporation

7 B - HOSE/GUN CABLE A 0 7 DETAIL A PCB,PCB7,PCB J AND J GH 7 0 DETAIL B HC HC B C B B B G A A D A GS G G TB G G G G GS C NOTES: )WIRE NO.C REQUIRED ONLY WITH IZUMI BREAKER NOTE: FOR SINGLE PHASE USE,CUSTOMER TO SUPPLY A SINGLE PHASE JUMPER CONNECTED FROM TB A TO TB B, JUMPER WIRE TO BE 0 GAUGE WIRE. (OPTIONAL ON UNISCAN R AND MULTISCAN R UNITS ) TB L L L L LOW LEVEL SWITCH (TB MOUNTED ON CENTER FRAME) (MOUNTED IN TANK) LOW LEVEL INDICATOR (OPTIONAL) 070/ Fig. B - Wiring Diagram for 00 Voltage Code Melters ( of ) 000 Nordson Corporation -000 Issued /00 BEN-0-[U-SCHEM]-

8 B - BEN-0-[U-SCHEM] Issued / Nordson Corporation