Field Service Spares Procedure Replacement Coax Switch Kit, 8897B, 9497B, 14400B, ST88, ST94 & ST144
|
|
- Brian Hart
- 6 years ago
- Views:
Transcription
1
2 1. Brief Summary: Troubleshooting document for diagnosing a fault with replacing the coax switch assembly on the 8897B, 9497B, 14400B, ST88, ST94 and ST144 antennas. 2. Checklist: Verify the Band of the Coax Switch Verify DC Voltage Switches the Coax Switch 3. Theory of Operation: The 8897B, 9497B, 14400B, ST88, ST94 and ST144 TVRO antennas feature a dual feed assembly supporting both C and KU band RF. A single quad linear KU band LNB is installed on the feed passing high horizontal, high vertical, low horizontal and low vertical RF paths through to the four channel rotary joint and in turn to the below decks distribution. Two separate C band LNB s are also installed on the feed assembly, one for horizontal polarization and one for vertical polarization. Both the low band KU RF paths are fed into the coax switch as are the C band horizontal and vertical paths meaning that the 4 channel rotary joint can be toggled between the 6 different RF paths depending on the required frequency range of the system. As default when the system initializes the C band RF will be selected, this means no voltage will be provided from the PCU to the coax switch assembly and ports J1 of the coax switches will be selected. Should KU band be selected from the tracking window of the DAC the PCU will output 12 15VDC to the coax switch assembly to select the J2 ports of the coax switched and in turn pass the low band KU RF paths to the rotary joint. 4. Troubleshooting the Coax Switch: Should the antenna not receive all of the KU band channels available then it s possible that the switch has failed and has defaulted to the C band channels. At this point the high band KU channels will still be received as there are fed directly into the rotary joint When KU band has been selected from the tracking window of the DAC it should be possible to measure 12 15VDC between pins 2 and 3 of the IDC connector on the coax switch assembly. If no voltage is present verify if the PCU/pol aux relay is outputting the voltage by measuring between the pins as stated on the below diagram for your model of antenna. If voltage is present but the coax switch has selected the C band RF paths the coax switch is defective and needs to be replaced. If no voltage can be measured on the IDC connector of the coax switch assembly or exiting the PCU/pol aux relay the PCU/pol aux relay isn t outputting the voltage, and needs to be replaced, if voltage can be measured on the PCU/pol aux relay but not on the IDC connector the harness is defective. Page 1 of 4
3 8879B, 9497B and 14400B ST88, ST94 and ST144 Page 2 of 4
4 5. Replacing the Coax Switch Assembly: 5.1. Tools. #1 Phillips Screwdriver 7/16 Wrench/Spanner Loctite Procedure. Procedure for replacing the RF switch assembly, Sea Tel kit part number: (RF switch assembly part number: ). *Caution: Power down the pedestal before following this procedure. 1. Using a #1 Phillips screwdriver remove the screw securing the coax switch connection of the reflector harness from the termination block. 2. Disconnect the coax switch IDC connector from the termination block. 3. Now disconnect the two RG 179 coax cables from the in output side of the coax switches using a 7/16 wrench. 4. Now disconnect the four RG 60 coax cables from the input side of the coax switches using a 7/16 wrench. Page 3 of 4
5 5. With all the cables removed from the coax switch remove the 4 screws securing the switch to the PCU assembly using a #1 Phillips screwdriver. Save the hardware for future use. 6. Install the replacement coax switch to the PCU assembly using the hardware removed in step 5 ensuring the P clips are installed on the lower screws. Apply Loctite 242 to the threads. 7. Reconnect the white and blue RG 179 coax cables to the coax switches as per the labels on the mounting plate. 8. Reconnect the four RG 60 coax cables to the coax switches matching the colors to the labels on the mounting plate. 9. Reconnect the IDC connector to the termination block on the PCB. 10. Secure the grounding point to the screw securing the termination PCB using a #1 Phillips screwdriver. Apply Loctite 242 to the thread. Page 4 of 4
Field Service Procedure Replacement Pol Motor Kit, Coastal
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the pol motor on the Coastal series antennas. 2. Checklist: Verify Motor Drive Drive the Pol from Progterm Run the Built
More informationField Service Procedure Level Cage Motor Kit, 2406
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the level cage motor on the 2406 antenna. 2. Checklist: Verify Initialization Verify Pointing Verify Targeting 3. Theory
More informationField Service Procedure PCU Kit, XX97, XX97A & XX00
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the PCU assembly on the XX97, XX97A and XX00 series antennas. 2. Checklist: Verify Initialization N0 Parameter Pedestal
More informationProcedure, Field Replacement, PCU Kit, 6003A/6004, 2406 & 4003A
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the PCU assembly on the 6003A/6004, 2406 & 4003A series antennas. 2. Checklist: Verify Initialization N0 Parameter Pedestal
More informationProcedure, Field Replacement, PCU Kit, XX04
1. Brief Summary: Troubleshooting document for diagnosing a fault with and replacing the XX04 series PCU assembly. 2. Checklist: Verify Initialization N0 Parameter Pedestal Error Test Motor 3. Theory of
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationArray Solutions WX0B StackMatch User's Guide
Array Solutions WX0B StackMatch User's Guide Thank you for purchasing the StackMatch. It has become a standard for phasing monoband and multi-band antennas.. The unit comes with our Life Time Warranty.
More informationArray Solutions StackMatch II User's Guide
Array Solutions StackMatch II User's Guide Thank you for purchasing the StackMatch II. Since the StackMatch introduction it has become a standard for phasing mono-band and multi-band beams, logs, quads,
More informationAmeritron ALS-600 Retrofit ALS-600-LPF Assembly Manual
Ameritron ALS-600 Retrofit ALS-600-LPF Assembly Manual FEATURES Automatic band change based on TX frequency. PIN diode QSK RX/TX switch. Temperature controlled FAN for quiet operation. RS-232 serial port
More informationDownload and read the Technical Description and Installation guide before deploying the PTP 820C equipment.
User Documentation Installation and operation of the PTP 820C is described in the PTP 820C Technical Description and PTP 820C Installation Guide available for download from: http://www.cambiumnetworks.com/support
More informationKit Kit. GeoSteer GS-900 Radio Kit. GS-900 Radio Kit Installation Instructions Rev A
200-0652-01 Kit 200-0652-02 Kit GeoSteer GS-900 Radio Kit Item Component Part Number Qty Notes 1. Assembly, Radio GS-900 200-0642-01 (North America) 200-0642-02 (Australia) 1 Radio assembly in kit is region
More informationM2 Antenna Systems, Inc. Model No: 450CP34
M2 Antenna Systems, Inc. Model No: 450CP34 SPECIFICATIONS: Model... 450CP34 Frequency Range... 435 To 455 mhz *Gain... 16.0 dbi Front to back... 22 db Typical Beamwidth... 28 Circular Feed type... T Match
More informationCross-Connect Interface
Cross-Connect Interface User Manual Document #: 050-015-0036R01 November 2006 TASC Systems Inc. Langley, BC Canada Cross-Connect System User Manual Preface This document describes the installation, commissioning
More informationSPL1500 CLASS B AIS SPLITTER
SPL1500 CLASS B AIS SPLITTER 1. Introduction Congratulations on the purchase of your SPL1500 Class B AIS Splitter. It is recommended that your Splitter is installed by a professional installer. This User
More informationMounting and Alignment Overview
CHAPTER 3 This chapter provides an overview of bridge mounting and antenna alignment. The following sections are included in this chapter: Mounting the Bridge, page 3-2 Mounting Hardware, page 3-2 Bridge
More informationMESA-HPX. Assembly and Installation Manual. w/appendix A for Prodelin Antenna. 901-Manual-MESA-HPX
MESA-HPX Assembly and Installation Manual w/appendix A for Prodelin Antenna 901-Manual-MESA-HPX Rev 30 March 2011 2 INDEX Installation Cautions 4 Installation Pole Height Orientation of the Mount on the
More informationQ U I C K R E F E R A N C E G U I D E. Tel: Fax:
Q U I C K R E F E R A N C E G U I D E Tel: 011 805 9098 Fax: 011 805 0174 www.comb-communications.com INDEX MAJOR COMPONENT LIST 1 WALL MOUNTING INSTRUCTIONS 2 FITTING THE SYSTEM TO A GOOSE NECK 2 PCB
More informationM2 Antenna Systems, Inc. Model No: 456CP34
M2 Antenna Systems, Inc. Model No: 456CP34 SPECIFICATIONS: Model... 456CP34 Frequency Range... 435 To 470 mhz *Gain... 16.0 dbi Front to back... 23 db Typical Beamwidth... 30 Circular Feed type... T Match
More informationIMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
INSTALLATI INSTRUCTIS Model: RB-G-K10 IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver system is intended to provide
More informationWildcat XX Stage 1 Audio Kit
2436-466 Wildcat XX Stage 1 Audio Kit WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are
More informationBMW E6x/E9x Android Touch Screen Radio Installation Instructions
BMW E6x/E9x Android Touch Screen Radio Installation Instructions Enjoy your new Android Radio from Bremmen Parts, we appreciate your business. Vibrant Touch Display This radio features a responsive 8.8
More informationKOP4800 Installation Guide
KOP4800 Installation Guide This guide contains installation and safety information for your KING One Pro. Please read thru this guide before using or installing your KING One Pro. QUESTIONS? (952) 345-8147
More informationKX2 Side KX installation
KX2 Side KX installation NOTE: The installation of any Side KX parts does NOT require the unsoldering of any connection nor removal of ANY of the boards from within the radio! The user/installer assumes
More informationBMW E90 Android Touch Screen Radio Installation Instructions
BMW E90 Android Touch Screen Radio Installation Instructions Enjoy your new Android Radio from Bremmen Parts, we appreciate your business. Vibrant Touch Display This radio features a responsive 9 touch
More informationInstallation Manual REbus Beacon. Part of the Pika Energy Island M
Installation Manual REbus Beacon Part of the Pika Energy Island M00020-01 REbus Beacon Serial Number: RCP Number: We are committed to quality and constant improvement. All specifications and descriptions
More informationINSTALLATION AND OPERATION MANUAL. Multiple-Radio Interface Module 41021G P-26 (11-12) 2012 David Clark Company Incorporated
INSTALLATI AND OPERATI MANUAL Multiple-Radio Interface Module 41021G-01 19537P-26 (11-12) 2012 David Clark Company Incorporated Table of Contents Cautions and Warnings... 1 Parts/Tools List... 2 Supplied
More informationRadio Control Installation and Operating Instructions System 4
Radio Control Installation and Operating Instructions System 4 P.O. Box 403, One Cedar Parkway, Jackson, WI 53037 Phone: 800-628-1909 Fax: 262-677-2058 Revision: April 19, 2012 Contents Introduction 3
More informationIMPORTANT: THIS DEVICE MUST BE PROFESSIONALLY INSTALLED. READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
INSTALLATI INSTRUCTIS Model: RB-G-K10 IMPORTANT: THIS DEVICE MUST BE PROFESSIALLY INSTALLED. READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI. The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver
More informationInstruction Manual. Quick Setup
Instruction Manual Quick Setup Make sure the Carryout G2 antenna is in a location with a clear view of the southern sky. Connect the provided coaxial cable from the primary receiver to the MAIN port on
More informationNEW DESIGN***DEM Part Number FRS***NEW DESIGN Low power 144 MHz Transverter for the Flex Radio System SDR-1000 Operating Specifications:
NEW DESIGN***DEM Part Number 144-28FRS***NEW DESIGN Low power 144 MHz Transverter for the Flex Radio System SDR-1000 Operating Specifications: Operating Voltage: 12.0-15.5 VDC, 13.8 nominal Current Drain:
More informationVinyl Cutter Instruction Manual
Vinyl Cutter Instruction Manual 1 Product Inventory Inventory Here is a list of items you will receive with your vinyl cutter: Product components (Fig.1-4): 1x Cutter head unit complete with motor, plastic
More informationDisclaimers. Important Notice
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
More informationFilm Scanner 24V Inverter Replacement
Overview Please read and understand the entire work instruction before beginning any procedures. WARNING: icrco assumes no liability for damage done to the unit while following these instructions. These
More informationM2 Antenna Systems, Inc. Model No: 435XP50
M2 Antenna Systems, Inc. Model No: 435XP50 SPECIFICATIONS: Model... 435XP50 Frequency Range... 430 To 436 MHz *Gain... 19.2 dbi Front to back... 22 db Typical Cross pol. isolation... >20 db Typical Beamwidth...
More informationM2 Antenna Systems, Inc. Model No: 2MCP22
M2 Antenna Systems, Inc. Model No: 2MCP22 SPECIFICATIONS: Model... 2MCP22 Frequency Range... 144 To 148 MHz *Gain... 14.39 dbic Front to back... 25 db Typical Elipticity... >3db Beamwidth... 38 Feed type...
More informationInstallation Guide. 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD
Installation Guide 2x2 MIMO Dish Antenna TL-ANT2424MD & TL-ANT5830MD Contents Introduction 1 Specifications 1 Safety Notice 2 Package Contents 2 Installation Requirements 3 Hardware Overview 3 Hardware
More informationPCB DESIGN AND MOUNTING
PULL-THRU USER S MANUAL: SECTION 1 PCB DESIGN AND MOUNTING TOOLS REQUIRED Phillips Head Screwdriver ASSEMBLY INSTRUCTIONS 1. Lay out, design, and manufacture PCB according to Figure A. The height of any
More informationInstallation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna
Release 3.0 NN47251-311 Issue 02.01 June 2014 Installation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna How to get help To access the complete range of services and
More informationM2 Antenna Systems, Inc. Model No: 450CP26
M2 Antenna Systems, Inc. Model No: 450CP26 SPECIFICATIONS: Model... 450CP26 Frequency Range... 445 To 455 mhz *Gain... 16.5 dbi Front to back... 21 db Typical Beamwidth... 30 Circular Feed type... T Match
More informationARP AVATAR PATCH PANEL INSTALLATION MANUAL
ARP AVATAR PATCH PANEL INSTALLATION MANUAL Introduction Thank you for purchasing an Avatar Patch Panel Kit! These instructions are intended to guide you through installing and using this kit. Before we
More informationP700WLS IoProx Receiver
Installation Manual Warning! This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual
More informationImproved Ionospheric Propagation With Polarization Diversity, Using A Dual Feedpoint Cubical Quad Loop
Improved Ionospheric Propagation With Polarization Diversity, Using A Dual Feedpoint Cubical Quad Loop by George Pritchard - AB2KC ab2kc@optonline.net Introduction This Quad antenna project covers a practical
More informationArc Trainer Main Frame Assembly
Arc Trainer Main Frame Assembly Kit No. 610AK019-4 Kit No. 630AK019-4 NOTE: This instruction sheet describes how to replace the main frame assembly in the Arc Trainer 610A. Tools Required 3/16 Allen wrench
More informationINSTALLATION AND OPERATION MANUAL FOR SEA TEL MODEL 8897B-1 C/KU-BAND TVRO ANTENNA
INSTALLATION AND OPERATION MANUAL FOR SEA TEL MODEL 8897B-1 C/KU-BAND TVRO ANTENNA Sea Tel, Inc. 4030 Nelson Avenue Concord, CA 94520 Tel: (925) 798-7979 Fax: (925) 798-7986 Email: seatel@cobham.com Web:
More informationAssembly Instructions. GK2200T TREADMILL ASSEMBLY INSTRUCTIONS Frame Assembly 120V 220V
GK2200T TREADMILL ASSEMBLY INSTRUCTIONS Frame Assembly 120V 220V IMPORTANT SAFETY INSTRUCTIONS Read and understand all instructions and warnings prior to use. Obtain a medical exam before beginning any
More informationM2 Antenna Systems, Inc. Model No: 2M4
M2 Antenna Systems, Inc. Model No: 2M4 SPECIFICATIONS: Model... 2M4 Frequency Range... 144 To 148 MHz *Gain... 9.6 dbi Front to back... 20 db Typical Beamwidth... E=54 H=74 Feed type... T Match Feed Impedance....
More informationPacific Antenna Easy TR Switch
Pacific Antenna Easy TR Switch Kit Description The Easy TR Switch is an RF sensing circuit with a double pole double throw relay that can be used to automatically switch an antenna between a separate receiver
More informationAUGMENT THE WEIGHT STACK SELECTION PRO SELECTION PRO MED INSTALLATION MANUAL
AUGMENT THE WEIGHT STACK SELECTION PRO SELECTION PRO MED INSTALLATION MANUAL REV 1.0 LANG: ENG DATE: 2016.06.03 1/33 SOMMARIO 1 INFORMATION NOTE... 4 2 TOOLS... 4 3 PERSONAL PROTECTIVE EQUIPMENT... 4 4
More informationTurboTuner-2 Automatic Screwdriver Antenna Controller Model YTT-450 For: Yaesu FT-450/950/ FTDX-1200/3000 User s Manual TennaTronix.
TurboTuner-2 Automatic Screwdriver Antenna Controller Model YTT-450 For: Yaesu FT-450/950/ FTDX-1200/3000 User s Manual TennaTronix.com Congratulations on purchasing the TurboTuner-2 Automatic Screwdriver
More informationInstallation Guide Flat Panel Antenna Mounting Kit For
Installation Guide Flat Panel Antenna Mounting Kit For 103670-1 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com
More informationInstruction Sheet P/N B Trim the new RTD wires. 5. Coat the new RTD with. 4. Strip the ends of the existing
Instruction Sheet P/N 1029716B 02 RTD Service Kit - P/N 1028320 02/08 Use this service kit to replace either the tank or the manifold RTD on any ProBluet or Mesat adhesive melter. If you are replacing
More informationInstalling and Upgrading Internal Modules in Cisco 1800 Series Routers (Modular)
CHAPTER Installing and Upgrading Internal Modules in Cisco 800 Series Routers (Modular) This chapter describes how to install or upgrade modules that are located internally within the Cisco 800 series
More informationHN System. Installation Manual for.74 m Ku-band Upgradeable Antenna Model AN6-074P
HN System Installation Manual for.74 m Ku-band Upgradeable Antenna Model AN6-074P 1037087-0001 Revision B October 19, 2006 Copyright 2006 Hughes Network Systems, LLC All rights reserved. This publication
More informationMFJ-219/219N 440 MHz UHF SWR Analyzer TABLE OF CONTENTS
MFJ-219/219N 440 MHz UHF SWR Analyzer TABLE OF CONTENTS Introduction...2 Powering The MFJ-219/219N...3 Battery Installation...3 Operation Of The MFJ-219/219N...4 SWR and the MFJ-219/219N...4 Measuring
More informationSDS TAP Retrofit Install Bartlett 3 Key Installation of TAP Control for Models Originally Built with the Bartlett 3 Key Control
SDS TAP Retrofit Install Bartlett 3 Key Installation of TAP Control for Models Originally Built with the Bartlett 3 Key Control This SDS Industries TAP Retrofit kit and installation instructions are intended
More informationM2 Antenna Systems, Inc. Model No:
M2 Antenna Systems, Inc. Model No: 400-600-10 SPECIFICATIONS: Model... 400-600-10 Frequency Range... 390 To 650 MHz *Gain... 12 To 13 dbic Front to back... 20 db Nominal Beamwidth... 46 Nominal Feed Impedance....
More informationProximity-Sensor Counter Installation Instruction Model: MRC-PRO
Proximity-Sensor Counter Installation Instruction Model: MRC-PRO NYS DOT Approval SYSDYNE CORP. 1055 Summer St. 1 st Floor Stamford, CT 06905 Tel: (203)327-3649 Fax: (203)325-3600 Contents: Introduction...
More informationABM International, Inc.
ABM International, Inc. Lightning Stitch required 1 1.0: Parts List head and motor assembly (Qty. 1) Reel stand (Qty. 1) Needle bar frame clamp (Qty. 1) Motor drive (Qty. 1) 2 Cable harness with bracket
More informationCM5500 COMPUTER MANAGED MORTISE LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More informationBy "Moleculo" - January 2011
pagina 1 van 17 By "Moleculo" - January 2011 NETHERLANDS Roermond Tel. +31 (0)475-327390 www.classicinternational.eu GERMANY Mönchengladbach Tel. +49 (0)2166-33061 www.classicinternational.eu pagina 2
More information7878 K940. Checkpoint Antenna. Kit Instructions. Issue B
7878 K940 Checkpoint Antenna Kit Instructions Issue B Revision Record Issue Date Remarks A July 7, 2009 First issue B Nov2013 Revised the Checkpoint installation procedures for 7878 and 7874 scanners Added
More informationMFJ-249B HF/VHF SWR ANALYZER
TABLE OF CONTENTS MFJ-249B... 2 Introduction... 2 Powering The MFJ-249B... 3 Battery Installation... 3 Alkaline Batteries... 3 NiCd Batteries... 4 Power Saving Mode... 4 Operation Of The MFJ-249B...5 SWR
More informationlilitab Counter 1.5 Packing List and Assembly Instructions
lilitab Counter 1.5 Packing List and Assembly Instructions 2339 3rd Street, Suite 59 support@lilitab.com San Francisco, CA 94107 t: 888.705.0190 www.lilitab.com v.1.0 TABLE OF CONTENTS LILITAB COUNTER
More informationIMPORTANT: THIS DEVICE MUST BE PROFESSIONALLY INSTALLED READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
INSTALLATI INSTRUCTIS Models: RB-G-K10, RB-TX10 IMPORTANT: THIS DEVICE MUST BE PROFESSIALLY INSTALLED READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI The Miller Edge RBand Monitored Gate
More informationmeped v2 Assembly Manual
meped v Assembly Manual The meped is an open source quadruped robot designed by Scott Pierce of Spierce Technologies, LLC. This design is released under the Creative Commons, By Attribution, Share Alike
More informationExercise 8. Troubleshooting a Radar Target Tracker EXERCISE OBJECTIVE
Exercise 8 Troubleshooting a Radar Target Tracker EXERCISE OBJECTIVE When you have completed this exercise, you will be able to apply an efficient troubleshooting procedure in order to locate instructor-inserted
More information2014 MFJ ENTERPRISES, INC.
Model MFJ-1907 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551 VERSION
More informationSM-RAZOR-T-M/L/XL. Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL
SM-RAZOR-T-M/L/XL Strong Low Profile Tilt Mount for Ultra-Thin Flat-Panel TVs INSTRUCTION MANUAL WARNINGS: Installation of this product should be done by a qualified professional. Do not begin installation
More informationINSTALLATION AND OPERATION MANUAL FOR SEA TEL MODEL DAC-2200 ANTENNA CONTROL UNIT
INSTALLATION AND OPERATION MANUAL F SEA TEL MODEL DAC-2200 ANTENNA CONTROL UNIT WARNING: Antenna Pedestal must be properly restrained (stowed) to prevent damage to wire rope isolators, isolator springs
More informationMFJ ENTERPRISES, INC.
Screwdriver Antenna Controller Model MFJ-1926 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment! MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel:
More informationTOYOTA TACOMA LED BED LIGHTS Preparation
Preparation Part Number: PT948-35160 Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver Side LED assembly 3 1 Passenger Side LED assembly 4 1 Main Wire Harness Hardware Bag Contents
More informationSAMYUNG SDA-450N Installation & Operation Manual Page 2
www.samyungenc.com www.samyungenc.com SAMYUNG SDA-450N Installation & Operation Manual Page 2 Marine Satellite TV Antenna Installation & Operation Manual SAMYUNG SDA-450N Copyright Notice: The information
More informationM2 Antenna Systems, Inc. Model No: 436CP30
M2 Antenna Systems, Inc. Model No: 436CP30 SPECIFICATIONS: Model... 436CP30 Frequency Range... 432 To 440 MHz *Gain... 15.50 dbic Front to back... 18 db Typical Elipticity... 1.5 db Typical Beamwidth...
More informationGMR 420/620/1220 xhd2 Series Installation Instructions
GMR 420/620/1220 xhd2 Series Installation Instructions To obtain the best performance and to avoid damage to your boat, install the device according to these instructions. Read all installation instructions
More informationRadiation characteristics of an array of two dipole antennas
Department of Electrical and Electronic Engineering (EEE), Bangladesh University of Engineering and Technology (BUET). EEE 434: Microwave Engineering Laboratory Experiment No.: A2 Radiation characteristics
More informationInstallation and Assembly: LCD UPRIGHT STAND FOR PEDESTAL CABINETS
Installation and Assembly: LCD UPRIHT STAND OR PEDESTAL CABINETS Part Number 49-5672-30 EATURES Take all of the guess work out of selecting the proper stand for your pedestal cabinets. This custom stand
More informationBMW E39/E53 Android Touch Screen Radio Installation Instructions
BMW E9/E5 Android Touch Screen Radio Installation Instructions Enjoy your new Android Radio from Bremmen Parts, we appreciate your business. Vibrant Touch Display This radio features a responsive 9 touch
More informationMFJ ENTERPRISES, INC.
TM Model MFJ-1924 INSTRUCTION MANUAL CAUTION: Read All Instructions Before Operating Equipment! MFJ ENTERPRISES, INC. 300 Industrial Park Road Starkville, MS 39759 USA Tel: 662-323-5869 Fax: 662-323-6551
More informationC-Leg Electric Height Adjustable Tables
C-Leg Electric eight Adjustable Tables Glides only Related tables: KCXE6030G KCXE7230G Unboxing You should have received your top plus two boxes per table. Box 1 includes: C-Leg assemblies, feet castings,
More informationM2 Antenna Systems, Inc. Model No: 2M5WL
M2 Antenna Systems, Inc. Model No: 2M5WL SPECIFICATIONS: Model... 2M5WL Frequency Range... 144 To 148 MHz *Gain... 16.84 dbi Front to back... 22 db Typical Beamwidth... E=26 H=29 Feed type... T Match Feed
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationINSTALLATION AND OPERATION MANUAL FOR SEA TEL MODEL: BROADBAND-AT-SEA TRANSMIT / RECEIVE SYSTEM
CAUTION: This stabilized antenna system is designed to be used with transmit/receive equipment manufactured by others. Refer to the documentation supplied by the manufacturer which will describe potential
More informationInstallation Instructions
Installation Instructions Optima LED 8 Double-Sided StretchLite Perimeter Lit Graphic Display Line Voltage Connector Optima LED DS5 (Double-sided StretchLite Graphic Display) with Graphics Corner Bracket
More informationHiSeasNet Maintenance Visit Report (Template dated 13 November 2007)
HiSeasNet Maintenance Visit Report (Template dated 13 November 2007) Page 1 Ship Visited: Ship Location/Port: R/V Oceanus Woods Hole, Massachusetts Date(s) of work: 23, 24 June 2008 Work performed by:
More informationGMR 420/620/1220/2520 XHD2 SERIES INSTALLATION INSTRUCTIONS
GMR 420/620/1220/2520 XHD2 SERIES INSTALLATION INSTRUCTIONS Important Safety Information WARNING See the Important Safety and Product Information guide in the product box for product warnings and other
More informationServo Amplifier - Troubleshooting Guide
Haas Technical Documentation Servo Amplifier - Troubleshooting Guide Scan code to get the latest version of this document Translation Available There are four versions of Haas amplifiers. 30A [1], 45A
More informationMobile TV Cart Instruction Manual SKU: STAND-TV03E Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product. https://vivo-us.com/products/stand-tv03e
More informationINSTRUCTION MANUAL FOR
No. TD05-28-1016 Date Mar.17,2005 INSTRUCTION MANUAL FOR Fiberoptic Rotary Joint Optical Component Engineering Information Systems Group Hitachi Cable, Ltd. 1. General This instruction manual describes
More information4 Antennas as an essential part of any radio station
4 Antennas as an essential part of any radio station 4.1 Choosing an antenna Communicators quickly learn two antenna truths: Any antenna is better than no antenna. Time, effort and money invested in the
More informationProgeny Integrated Mobile Unit Unpacking/Assembly Guide
Summary: The following instruction will guide you through the unpacking and installation of the Progeny Mobile Unit. Any question or concerns or suggestions should be directed to Progeny Technical Support
More information* * APPLICABLE MODELS: 2014 > MAZDA 3
PART NUMBER: 0000 8C L46 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0604-000* APPLICABLE MODELS: 204 > MAZDA 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationCM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More informationQ-SERIES. Amplifiers. QPAIR Redundancy Switch Amplifier System. Installation & Operation Manual
Q-SERIES Amplifiers QPAIR Redundancy Switch Amplifier System Installation & Operation Manual Although every effort has been taken to ensure the accuracy of this document it may be necessary, without notice,
More informationRedundant LNA Systems
< 1:1 LNA Plate Assembly with RCP2-1100 LNA PLATE Compact plate assemblies facilitate convenient antenna hub mounting Standard feed orientations State-of-the-art noise temperatures provided by Paradise
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SELF LEVELING RADAR ANTENNA MOUNT MODEL 400G QUESTUS MARINE, INC. PO BOX 9 MARBLEHEAD, MA 01945 1-800-RADAR66 TEL 781.639.1900 FAX 781.639.1905 www.questusmarine.com INSTALLATION
More informationCommercial Vehicle Productivity and Security. Antenna Configuration. External Antenna Installation (model 6650H only) Contigo 6650H/6651H Beacon
Commercial Vehicle Productivity and Security The 6650H/6651H is a versatile and economical GPS tracking beacon designed for fleet management needs in all commercial vehicles. The H designation in the model
More informationDirective Systems & Engineering 2702 Rodgers Terrace Haymarket, VA
Directive Systems & Engineering 2702 Rodgers Terrace Haymarket, VA 20169 1628 www.directivesystems.com 703 754 3876 K1JX DESIGNED 6 ELEMENT 50 MHZ YAGI, DSEJX6 50 INTRODUCTION The Directive Systems DSEJX6-50
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL PREFACE This installation & operation manual is intended as an instruction manual for trained person who is in charge of installation, maintenance, repair, etc. Before installation
More informationFIELD SERVICE BULLETIN
HUGHES NETWORK SYSTEMS FIELD SERVICE BULLETIN SUBJECT: Hughes Universal Ku-band Radio Assemblies FSB NUMBER: FSB ISSUE DATE: FSB_130919_01C 09/16/2013 SUBMITTED BY: P. Hari, M. Middeke APPROVED BY: D.
More informationM2 Antenna Systems, Inc. Model No: 2M7
M2 Antenna Systems, Inc. Model No: 2M7 SPECIFICATIONS: Model... 2M7 Frequency Range... 144 To 148 MHz *Gain... 12.3 dbi Front to back... 20 db Typical Beamwidth... E=43 H=50 Feed type... T Match Feed Impedance....
More information