Download and read the Technical Description and Installation guide before deploying the PTP 820C equipment.

Transcription

1 User Documentation Installation and operation of the PTP 820C is described in the PTP 820C Technical Description and PTP 820C Installation Guide available for download from: Download and read the Technical Description and Installation guide before deploying the PTP 820C equipment. Application firmware Download and install the latest PTP 820C firmware before deploying the PTP 820C equipment. EU declaration of conformity Hereby, Cambium Networks declares that the PTP 820C complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at: Enquiries and support MultiCore 2+0 Dual Polarization Direct Mount 1 PTP 820C RADIO 1 2 PTP 820C OMT KIT 1 Required Tools Metric offset hexagon key set Metric wrench key set 1

2 Procedure 1 Prior to the installation, follow the antenna manufacturer s instructions to use the circular adaptor. (Remove the existing rectangular transition, swap the O-ring, and install the circular transition instead.) 2 Connect the OMT Kit to the antenna and secure it with four screws. Verify the existence of the O-ring. 3 Connect the PTP 820C radio to the OMT Kit using the four M8 captive screws and washers supplied and tighten the screws. MultiCore 2+0 Single Polarization Direct Mount 1 PTP 820C RADIO 1 2 PTP 820C SPLITTER KIT 1 Required Tools Metric offset hexagon key set Phillips #1, #2 screwdriver Procedure 1 Adjust the alignment of the Splitter Kit according to the required polarization. 2

3 For horizontal polarization, locate the holes such as the letter H is on top and fasten For vertical polarization, locate the holes such as the letter V is on top and fasten 2 Mount and tighten the PTP 820C Splitter Kit on the antenna using the four M8 screws and washers. 3 Mount and tighten the PTP 820C radio to the PTP 820C Splitter Kit using the four M8 captive screws and washers supplied. MultiCore 2+2 HSB or 2 x MultiCore 2+0 Double Polarization Direct Mount 1 PTP 820C RADIO 2 2 PTP 820C OMT KIT 1 3 PTP 820C DUAL COUPLER KIT 1 Required Tools Metric offset hexagon key set Metric wrench key set 3

4 Procedure 1 Prior to the installation, follow the antenna manufacturer s instructions to use the circular adaptor. (Remove the existing rectangular transition, swap the O-ring and install the circular transition instead.) 2 Connect the PTP 820C OMT Kit to the antenna and secure it with four screws. Verify existence of the O-ring. 3 Connect the PTP 820C Dual Coupler Kit to the OMT Kit using four M8 screws and washers, and tighten the screws. 4 Mount and tighten the PTP 820C radio unit to both sides of the Dual Coupler Kit using the supplied captive screws and washers. Pay attention that the O-rings are correctly mounted on the radio ports of the PTP 820C Dual Coupler. MultiCore 2+2 HSB Single Polarization Direct Mount 1 PTP 820C RADIO 2 2 PTP 820C SPLITTER KIT 1 3 DUAL COUPLER KIT 1 4

5 Required Tools Metric offset hexagon key set Metric wrench key set Phillips #1 screwdriver Procedure 1 Adjust the alignment of the Splitter Kit according to the required polarization. For horizontal polarization, locate the holes such as the letter H is on top and fasten For vertical polarization, locate the holes such as the letter V is on top and fasten 2 Mount the Splitter Kit on the antenna using four M8 screws and washers and tighten the screws. 5

6 3 Connect the PTP 820C Dual Coupler Kit to the PTP 820C Splitter Kit using four M8 screws and washers and tighten the screws. 4 Connect the PTP 820C radio unit to both sides of the Dual Coupler Kit using the supplied captive screws and washers and tighten the screws Cable Installation and Grounding Cables must be grounded as follows: For optical (SFP) cables, no grounding is required. For Ethernet cables, the cable must be grounded to the antenna tower every 50m using the kit CAT5E_gnd_kit. Grounding cable must be grounded to tower close to the radio installation. Radio Grounding Installation 1 On the front of each PTP 820C unit, loosen the nut, plain washer and serrated washer. 2 Place the cable lug (supplied with the PTP 820C grounding kit) on the screw. 3 Secure the cable lug. Connecting the Cables to the PTP 820C 1 Disassemble the relevant cap from the PTP 820C radio 6

7 2 Connect the cable with the gland assembled to PTP 820C Radio. 3 Attach and tighten the gland to the PTP 820C. 4 Secure the cable to the gland using a tie wrap. Caution For the warranty to be honored, you must install the unit in accordance with the instructions above. 7