INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1
|
|
- Verity Loraine Gilbert
- 5 years ago
- Views:
Transcription
1 INSTALLATION INSTRUCTIONS Medium Flat Panel Model MSP-SI1 IMPORTANT! : The MSP-S11 Mount is designed for use with Sharp 45" LCD displays that have a 200mm x 200mm mounting pattern. IMPORTANT! : The mount has a maximum weight capacity of 75lbs (34kg), and an outward maximum extension of 7.25"(184.15mm). BEFORE YOU BEGIN WARNING: Thoroughly read and understand all Warnings and precautions (see page 2), instructions and illustrations before you begin mount installation. Failure to install the mount properly could lead to serious personal injury, damage to equipment, and may void the factory warranty. WARNING: Mount faceplate moves freely from retracted to extended position. Keep hands and fingers away from pinch points while unpacking, handling and installing the mount. If you have any questions about this installation, contact Chief Manufacturing at CHIEF MANUFACTURING INC FAX EAGLE CREEK PARKWAY, STE 700 SAVAGE, MINNESOTA USA Rev B 2006 Chief Manufacturing 06/06
2 Model MSP-SI1 Installation Instructions IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions. WARNING: Improper installation can result in serious personal injury! Make sure that structure can support a weight factor five times the total weight of the equipment. If not, reinforce the structure before installing mount. WARNING: Mount faceplate moves freely from retracted to extended position. Keep hands and fingers away from pinch points while unpacking, handling and installing the mount. WARNING: The weight of the display placed on the mount must not exceed 75 lbs. (34 kg), the maximum load capacity of the mount. CAUTION: Check the unit for shipping damage before you begin the installation. NOTE: Use only the mounting screws provided and DO NOT OVER TIGHTEN. Dimensional Drawing 2
3 Installation Instructions INTRODUCTION TOOLS REQUIRED FOR INSTALLATION Phillips screwdrivers, No. 1 and No. 2 TIP Drill and bit set 1/8" Hex Key (provided) M4 Hex Key (provided) 5/32" Hex Key (provided) 4 each 1/4" Lag Screw (not included with mount) NOTE: Other tools may be required depending on the method of installation. INSPECT MOUNT BEFORE ASSEMBLY Carefully inspect mount assembly for shipping damage (see Figure 1). If damage is apparent, call your carrier claims agent and do not continue with installation until the carrier has reviewed the damage. NOTE: Thouroughly read and understand all assembly instructions before starting installation. Table 1: PARTS Model MSP-SI1 ITEM DESCRIPTION QTY. 10 Mount Assembly 1 20 SCREW, Phillips Machine, M6 x 40mm (Silver) 30 PLATE, Holding 4 40 WASHER, Flat, 1/4" 4 50 KEY, Hex 5/32" (provided) 1 60 PAD, Felt, 1" 2 70 CLIP, Cable Management 2 80 BRACKET, Interface 200 x SCREW, Phillips Machine, M6 x 25mm SCREW, Phillips Machine, M6 x 40mm (Black) 110 SCREW, Button Head Cap, M6 x 20mm SPACER, Nylon, 3/4" x 1/8" SPACER, Nylon, 3/4" x 1/4" KEY, Hex 1/8" (provided, not shown) KEY, Hex M4 (provided, not shown) SCREW, Lag, 1/4" (required, not provided) , 100, or , or Figure 1: Parts 3
4 Model MSP-SI1 Installation Instructions MOUNT ASSEMBLY The only assembly required on the SI1 is attaching a cable management clip to each side of the mount face plate. To attach the cable management clip: 1. Pull mount face plate outward until access to rear of face plate can be achieved. 2. Install two cable management clips (70) into each side of mount faceplate. (see figure 2) Face Plate 4. Place mount assembly (10) against wall and align mounting holes in mount assembly (10) with pilot holes (see figure 4). 5. Insert four M6 x 40mm Phillips machine screws (20) with four 1/4" flat washers (40) through mount assembly (10) and wall and into four holding plates (30) located behind wall (see figure 4). 1/4" Pilot Hole (Mark and Drill) Mount Assembly (10) Cable Management Clip Figure 3: Locate, Mark and Drill Pilot Holes Mount Assembly (10) Holding Plate (30) Figure 2: Install Cable Management Clips MOUNT INSTALLATION WARNING: The installer is responsible for verifying that the structure to which the mount is anchored will safely support five times the combined load of the mount and all attached components. Mount Installation With Holding Plates To install mount using Holding Plates: 1. Identify appropriate mounting location. 2. Place mount assembly (10) against wall and mark pilot hole locations (see figure 3). WARNING: Keep hands and fingers away from pinch points as mount may move from retracted to extended position when being positioned on wall. 3. Drill four 1/4" pilot holes, at marked locations (see figure 3). 1/4" Flat Washer (40) M6 x 40mm Phillips Machine Screw (20) Figure 4: Secure Mount to Wall 4
5 Installation Instructions Mount Installation into Dual Wood Studs WARNING: The installer is responsible for verifying that the structure to which the mount is anchored will safely support five times the combined load of the mount and all attached components. To install mount using dual wood studs on 16" center: 1. Identify appropriate mounting location and wood studs. 2. Place mount assembly (10) against wall, level mount and mark pilot hole locations (see figure 5). Model MSP-SI1 3. Secure interface bracket (80) to display using four M6 x 20mm button head cap screws (110). NOTE: If mounting surface is recessed use four M6 x 25mm Phillips Machine screws (90) with spacer (120) or four M6 x 40mm Phillips Machine screws (100) with spacer (130). 4. Tighten all screws. Display Back WARNING: Keep hands and fingers away from pinch points as mount may move from retracted to extended position when being positioned on wall. Spacer (120 or 130) 3. Drill four 1/8" pilot holes, at marked locations (see figure 5). 4. Secure mount to wall studs using four flat washers (40) and four lag screws (160). (see figure 5) Wood Studs 1/8" Pilot Holes (4 places) Interface Bracket (80) Screw (90, 100, or 110) Figure 6: Install Interface Bracket 5. Move mount (10) faceplate to extended position by grasping faceplate and pulling outward, away from wall. WARNING: Keep hands and fingers away from all pinch points when moving the mount from retracted to extended position. (160) (10) (40) (4 places) (4 places) Figure 5: Install Mount on Dual Wall Studs INSTALL DISPLAY To install the display: 1. Lay display face down on a clean dry surface. 2. Align holes in interface bracket (80) with mounting holes in display back. 6. Align mounting buttons on display with teardrop mounting holes in mount faceplate (see figure 7). 7. Move display forward until all four mounting buttons (40) are through teardrop mounting holes in faceplate, and recessed area of mounting buttons (40) is aligned with the lower area of teardrop mounting holes in faceplate. 8. Lower display until the recessed area of all four mounting buttons is seated in the lower area of teardrop mounting holes in faceplate (see figure 8) 9. Move two latch flags to their UP position to secure display to mount assembly. 5
6 Model MSP-SI1 Installation Instructions Mounting Button FELT PAD INSTALLATION Felt pads (60) are provided to protect the display from contact with the mount. To install protective felt pads: 1. Move display to fully extended position. WARNING: Keep hands and fingers away from all pinch points when moving the mounted display from the retracted to the extended position. Faceplate Teardrop Mounting Hole Figure 7: Install Display on Mount Assembly Faceplate Mounting Button Latch Flags (Shown in Locked Position) Teardrop Mounting Hole Figure 8: Install Display on Mount Assembly 2. Slowly rotate display to "fully right" position and identify the area of contact between the display and cabinet. 3. Remove adhesive back from felt pad (60) and place pad onto display at identified point of contact. 4. Slowly rotate display to "fully left" position and identify the area of contact between the display and cabinet. 5. Remove adhesive back from felt pad (60) and place pad onto display at identified point of contact. ADJUSTMENTS The mount is shipped with pre-set tension for swing arm movement. After extended use mount tension may need to be adjusted. There are a total of 12 tension adjustment points on the mount (see figure 9). Six on mount top, and six on mount bottom. Points 1 through 6 control mount extension and retraction tension. Points 1 and 6 control mount right left swing tension, and points 3 and 4 control display left right rotation tension. NOTE: It is important that correspnding points are adjusted equally. Example: 1 and 6, 2 and 5, 3 and 4, and their corresponding adjustment points on mount bottom (see figure 9). To adjust mount tension: 1. Determine which aspect of mount movement needs to be adjusted and located appropriate adjustment screws. 2. Using the hex wrench provided, tighten or loosen adjustment screws until desired tension is achieved (see figure 9). CABLE MANAGEMENT Cable management clips, for use with "zip-ties" or similar devices, are provided for routing and securing cables running to the mounted display. To use cable management clips: 1. Zip tie cable to cable clip (70). (see figure 10) 2. Route cables down and under mount to display. 6
7 Installation Instructions Model MSP-SI1 Decrease Tension Increase Tension Figure 9: Tension Adjustment Points Zip Tie Cable Management Clip (70) Cable Figure 10: Cable Routing 7
8 Model MSP-SI1 Installation Instructions 8
SPOM1 INSTALLATION INSTRUCTIONS. Medium Flat Panel Wall Mount. Instrucciones de instalación Installationsanleitung Instruções de Instalação
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Medium Flat Panel
More informationMedium Flat Panel Dual Swing Arm Wall Mount JWD-V
INSTALLATION Medium Flat Panel Dual Swing Arm Wall Mount The single swing arm wall mount is designed for mounting a medium sized flat panel display. The can swing out from, or fold against, the wall depending
More informationFlat Panel Dual Swing Arm Wall Mount (FWD-110) MSP-SA
INSTALLATION INSTRUCTIONS Flat Panel Dual Swing Arm Wall Mount (FWD-110) The dual arm wall mount was designed to support flat panel displays with 10 to 30 diagonal screens and weighing a maximum of 40
More informationMSP-DCCPGSU Large Screen Static Display Mount
INSTALLATION INSTRUCTIONS Large Screen Static Display Mount The Large Screen Static Display Mount () is a quick disconnect mounting solution for large flat panel displays. The mount self-adjusts for the
More informationSpeaker Mount Center Channel Speaker Adapter (PAC-301)
I N S T R U C T I O N M A N U A L Speaker Mount Center Channel Speaker Adapter () The Speaker Mount Center Channel Speaker Adapter () uses the same interface as the Side Speaker Adapter and can be used
More informationMSP-DCCPGTU Large Screen Tilt Display Mount
INSTALLATION INSTRUCTIONS Large Screen Tilt Display Mount The Large Screen Tilt Display Mount is a quick disconnect mounting solution for large flat panel displays. The mount features infinite adjust ability
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More informationMEDIUM FLAT PANEL DISPLAY TILT MOUNT MSP-MT (MTR-V)
INSTALLATION INSTRUCTIONS MEDIUM FLAT PANEL DISPLAY TILT MOUNT (MTR-V) The tilt mount accommodates medium flat panel displays weighing up to 100 lbs (45.36kgs). The teardrop holes in the mount allow for
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000
INSTALLATION INSTRUCTIONS HEAVY DUTY TILT WALL MOUNT Model: PPH-2000 Specifications: Accomodates Akira and Orion 84" displays without interface bracket; accomodates other large flat panel displays with
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable, Extended Pitch Swing Arm Wall Mount Model KWE-110 The KWE dual swing arm wall mount is designed to provide a broad range of viewing for Small
More informationMedium Flat Panel Universal Interface Bracket (MSB-V)
INSTALLATION Medium Flat Panel Universal Interface Bracket () INSTRUCTIONS The interface bracket functions as the universal mounting solution for medium flat panel displays. The is compatible with a multitude
More informationModel MSPPWRTW Large Flat Panel Single Arm Wall Mount
INSTALLATION INSTRUCTIONS Model Large Flat Panel Single Arm Wall Mount The is wall-mounted, rugged, versatile, and installer-friendly. The mount is compatible with the standard (14 x 14 ) PSB interface
More informationINSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays Models: FMA-220 and FMA-320
INSTALLATION INSTRUCTIONS Small Flat Panel FMA Pivot Arrays The FMA-220 and FMA-320 pivot array allow both horizontal and vertical display pitch adjustment. The pitch adjustment range is 30 (15 up / 15
More informationINSTALLATION INSTRUCTIONS. Large Flat Panel Wall Mount Model: PRO-2000 Series
INSTALLATION INSTRUCTIONS Large Flat Panel Wall Mount Model: PRO-2000 Series PRO-2000 Series Wall Mount Features: Accommodates large flat screens weighing up to 200 lbs (90.7 kg). Mounting brackets adapt
More informationMSP-DCCLFSD LCD Flat Screen Swing-Down Mount
INSTALLATION INSTRUCTIONS LCD Flat Screen Swing-Down Mount Perfect for home applications under kitchen cabinets or other rooms with a soffit. The LCD Flat Screen Swing-Down mount is a sturdy, versatile
More informationPART #MSP-DCCPPWS Plasma Wall Swing-Out (PWS) Wall Mount
I N S T R U C T I O N M A N U A L PART # Plasma Wall Swing-Out (PWS) Wall Mount The wall mount is a rugged, versatile, and installer-friendly solution to unique display mounting requirements. With the
More informationFSD-4100 LCD Flat Screen Swing-Down Mount
INSTALLATION INSTRUCTIONS LCD Flat Screen Swing-Down Mount Perfect for home applications under kitchen cabinets or other rooms with a soffit. The LCD Flat Screen Swing-Down mount is a sturdy, versatile
More informationINSTALLATION INSTRUCTIONS Lateral Shift Accessory Model: PAC-800
INSTALLATION INSTRUCTIONS Lateral Shift Accessory Model: PAC-800 The PAC-800 Lateral Shift Accessory is for use with Chief Model PSM, PST, PRO, PLP, Large Flat Panel Display wall mounts. It can be installed
More informationWMA-300 Single Stud Wall Arm
INSTALLATION INSTRUCTIONS Single Stud Wall Arm The Single Stud Wall Arm can be used to wall mount RPA, UPC or LCDA series ceiling mounts. The also provides a mounting solution for TV/Monitor mounts. The
More informationFlat Panel Tilt Wall Mount (GPM-111)
INSTALLATION INSTRUCTIONS Flat Panel Tilt Wall Mount () The tilt wall mount fits most 23 to 30 displays. The is designed to adapt to VESA 200mm/100mm compliant displays. This mount will also adapt to standard
More informationSmall Flat Panel Height-Adjustable Dual Swing Arm Wall Mount With Universal Slat Wall Mount (MSP-JS-KWG-110)
INSTALLATION INSTRUCTIONS Small Flat Panel Height-Adjustable Dual Swing Arm Wall Mount With Universal Slat Wall Mount () The dual swing arm desk mount is a sleek design providing a broad range of viewing
More informationINSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series
INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option
More informationINSTALLATION INSTRUCTIONS MSP-SPFB (PFB-2000S) Plasma Floor Stand
INSTALLATION INSTRUCTIONS MSP-SPFB (PFB-2000S) Plasma Floor Stand Chief s Plasma Floor Stand is a safe, stable, easy-toinstall modular design solution for digital signage and presentations. Ideal where
More informationLARGE FLAT PANEL DISPLAY STATIC MOUNT PST 2000 Series
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL DISPLAY STATIC MOUNT The PST static wall mount accommodates large flat screens weighing up to 200 lbs (90.72kg). The teardrop holes in the mount allow for quick
More informationPART #MSP-DCCST Flat Panel Tilt Mount
INSTALLATION INSTRUCTIONS PART # Flat Panel Tilt Mount The Flat Panel Tilt Mount is a quick disconnect mounting solution for flat panel displays. The mount features adjustability between 0 and 15 degrees
More informationCTA-100 VCR / DVD / Cable Box Adapter
INSTALLATION INSTRUCTIONS VCR / DVD / Cable Box Adapter The provides a centralized mounting solution for a VCR/DVD/cable box. The shelf on the can be adjusted to fit the width and height of most VCR/DVD/Cable
More informationMobile Cart for Flat Panel Display MSP-SPTC42 (PTC-2000 Series)
INSTALLATION INSTRUCTIONS Mobile Cart for Flat Panel Display (PTC-2000 Series) The Mobile Cart for Flat Panel Display is designed to assist the presenter in showrooms, boardrooms, and trade show exhibits.
More informationTruss Pitch-Adjustable (TPP) Mount
I N S T R U C T I O N M A N U A L Truss Pitch-Adjustable (TPP) Mount The Truss Pitch-Adjustable (TPP) mount is a perfect solution exhibit, retail and digital signage applications. The mount is quick, easy
More informationMobile Cart for Flat Panel Display (PTC-2000 Series)
INSTALLATION INSTRUCTIONS Mobile Cart for Flat Panel Display ( Series) The Mobile Cart for Flat Panel Display is designed to assist the presenter in showrooms, boardrooms, and trade show exhibits. The
More informationINSTALLATION INSTRUCTIONS Display Interface Model: FSB-V
INSTALLATION INSTRUCTIONS Display Interface Model: FSB-V BEFORE YOU BEGIN CAUTION: To prevent damage that could affect or void the Factory warranty, and to the equipment that will be attached to it, thoroughly
More informationINSTALLATION INSTRUCTIONS Plasma Floor Stand (PFB-2000SB)
INSTALLATION INSTRUCTIONS Plasma Floor Stand (PFB-2000SB) Chief s Plasma Floor Stand is a safe, stable, easy-toinstall modular design solution for digital signage and presentations. Ideal where wall or
More informationINSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011
INSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011 Specifications: Installs to K-Series desk or wall mount. Accommodates K-Series mounting arms (fixed
More informationINSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500
INSTALLATION INSTRUCTIONS LARGE FLAT PANEL IN WALL ENCLOSURE Model: PAC-500 Specifications: Designed for in-wall installation spanning a minimum of 3 wood studs, 16" on center. Accomodates MWR, PWR and
More informationINSTALLATION INSTRUCTIONS POLE/PITCH- ADJUSTABLE MOUNT Model: TPM-2000 SERIES
INSTALLATION INSTRUCTIONS POLE/PITCH- ADJUSTABLE MOUNT Model: TPM-2000 SERIES Specifications: Weight capacity of 150 lbs. (68 kg). Provides tilt range from 5 up to 15 down. Accommodates vertical pole (1"
More informationINSTALLATION INSTRUCTIONS. PLASMA TV WALL MOUNT TILT Universal (RGTU-210) WARNINGS WARNING
PLASMA TV WALL MOUNT TILT Universal (RGTU-210) S CAUTION CAUTION CAUTION A alerts you to the possibility of serious injury or death if you do not follow the instructions. A CAUTION alerts you to the possibility
More informationINSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series
INSTALLATION INSTRUCTIONS SMALL FLAT PANEL ADJUSTABLE PITCH WALL MOUNT Model: FTR Series Specifications: Designed for installation on single wood studs or drywall (1/2" minimum thickness); either option
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationMSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit for use with Island Display Skybox
INSTALLATION INSTRUCTIONS MSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit for use with Island Display Skybox The MSP-WRTIDSKY1 Light Weight Suspended Ceiling Kit provides a sturdy support for LCD displays
More informationINSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series
INSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories The KTP-Series is a free standing, pole mount solution for multiple displays. KTP-320 KTP-220 / KTP-225 KTP-440 / KTP-445
More informationPlasma Presenters Cart (PPC-2000)
I N S T R U C T I O N M A N U A L (PPC-2000) The (PPC) is designed to assist the presenter in showrooms, boardrooms, and trade show exhibits. The PPC provides agile mobility for screens weighing up to
More informationLCD TV WALL MOUNT INSTALLATION INSTRUCTIONS. DUAL Swing Arm (RFWD-110) WARNING
INSTALLATION INSTRUCTIONS LCD TV WALL MOUNT DUAL Swing Arm (RFWD-110) WARNINGS WARNING WARNING CAUTION CAUTION The maximum weight to be installed on the RFWD wall mount is 40 lbs. (18.1 kg). The RFWD is
More informationINSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS
INSTALLATION INSTRUCTIONS SLBU / SLMU UNIVERSAL INTERFACE BRACKETS The Universal Interface Bracket provides a solution for simplifying inventory of RPA and RPM series mounts and SLB/SLM projector brackets.
More informationINSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series
INSTALLATION INSTRUCTIONS Horizontal And Vertical Table Stands and Accessories Model: KTP-Series The KTP-Series is a free standing, pole mount solution for multiple displays. KTP-320 KTP-220 / KTP-225
More informationLCD MONITOR/TV WALL MOUNT
INSTALLATION INSTRUCTIONS LCD MONITOR/TV WALL MOUNT DUAL DESK CLAMP (RFCD-110) S CAUTION CAUTION A alerts you to the possibility of serious injury or death if you do not follow the instructions. A CAUTION
More informationINSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series
INSTALLATION INSTRUCTIONS Small Flat Panel Mounts Model: F-Series This Instruction Manual covers most of the F-Series wall and desk mounts, as well as selected F-Series pole mounts. NOTE: Some F-Series
More informationCMA-455 Suspended Ceiling-Tile Reinforcing Kit
INSTALLATION INSTRUCTIONS CMA-455 Suspended Ceiling-Tile Reinforcing Kit The provides a sturdy support for LCD/DLP hanging brackets (and certain other products) when installing these products in a suspended
More informationIMPORTANT WARNINGS AND CAUTIONS!
I N S T R U C T I O N M A N U A L The Christie Vivid Green ceiling mount will suspend your Christie Vivid Green projector in an upright position to compliment conference rooms, classrooms or home theater
More informationDual Arm Tilt LCD Mount
Installation Manual model # 51324 M o u n t i n g S y s t e m s Dual Arm Tilt LCD Mount Fits Displays 13 to 32 Supports Up to 50 lbs (23 kgs) Projection from Wall from 3 to 17 Meets VESA Standards 50/75/100,
More informationSAM. Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual. Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" Page 20
SAM Model: STV-C65 LCD Mobile Visualized Stand Instruction Manual Weight Capacity: 1251bs / 56.7kg Suits LCD Flat Panel Display: 42"-55" 20 Step 6 LCD Mobile Lift Stand Model: STV-C65 Cable management
More informationPNRIW Series INSTALLATION INSTRUCTIONS. Large Flat Panel In-Wall Swing Arm Mount
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Large Flat Panel In-Wall
More informationPNRIW / PNRIWU INSTALLATION INSTRUCTIONS. Large Flat Panel In-Wall Swing Arm Mount
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Large Flat Panel In-Wall
More informationOB1U INSTALLATION INSTRUCTIONS. Interactive Flat Panel Over White Board Mount
INSTALLATION INSTRUCTIONS Interactive Flat Panel Over White Board Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationSTORM OUTDOOR TELEVISION MOUNT
Model: TW-1 INSTRUCTION MANUAL STORM OUTDOOR TELEVISION MOUNT Tilting Wall Mount www.seura.com Thank you for selecting Séura s Outdoor Tilting Wall Mount for Storm. This product has been inspected and
More informationUniversal Projector Ceiling Mount Model: DPM-45
Universal Projector Ceiling Mount Model: DPM-45 Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information represented within this
More informationInstalling flat panels on the MPL15 wall mount
Installing flat panels on the MPL15 wall mount The MPL15 (DS-VW775) is a full-service video wall mount that can accommodate tiled LCD panels with up to a 400 x 400 mm VESA pattern in portrait and landscape
More informationINSTALLATION INSTRUCTIONS. Yamaha Speaker Adapter Accessory PAC-Y3
INSTALLATION INSTRUCTIONS Yamaha Speaker Adapter Accessory DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate
More informationLC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns
Page 1 of 6 LC200DS1 Double Stud Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns A multi-position dual articulating arm for flat screens up to 60
More informationPFW 6851 Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS
Display Wall Mount, Turn & Tilt 80 kg INSTALLATION INSTRUCTIONS 9531-007-Z00-01 Table of Contents Warning Statements 2 Parts List 3 Installation Tools 3 Wood Stud Installation 5 Concrete Surface Installation
More informationLC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns
LC200DS2 Double Stud Dual Articulating Wall Mount for Flat Panel Screens up to 32" with up to 200mm x 200mm VESA Mounting Patterns Multi-position triple pivoting arms allows you to position the monitor
More informationAssembly Instructions for Model: MF110
Assembly Instructions for Model: MF110 Thank you for choosing a Sanus Systems VisionMount wall mount. The MF110 is designed to mount LCD flat panels with VESA (Video Electronics Standards Association)
More informationSB-WM-ART1-M-BL. Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL
SB-WM-ART1-M-BL Weatherproof Universal Single-Arm Articulating Mount for Medium Displays INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 90 lbs (41 kg). Use with heavier than the maximum
More informationQMP2MM1 INSTALLATION INSTRUCTIONS. Music Stand Height Adjust Single Monitor
INSTALLATION INSTRUCTIONS Music Stand Height Adjust Single Monitor Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description
More informationINSTALLATION GUIDE. Model:B60 RECESSED IN WALL MOUNT
INSTALLATION GUIDE Model:B60 RECESSED IN WALL MOUNT Features: Installs between 16 (406mm) wood stud centers Mounting Pattern Compliance: VESA 100*100mm up to 600 x 400mm Level 5 degree horizontal adjustment
More informationSM-RAZOR-ART2-L / SM-RAZOR-ART2-XL
SM-RAZOR-ART2-L / SM-RAZOR-ART2-XL Strong Razor Series Articulating Mount for Large and Extra Large Displays INSTRUCTION MANUAL Installation Manual Warnings: Installation of this product should be done
More informationLC6X4WTM Security Wall Mount with Tilt for up to 60" Flat Screens with VESA 600mm x 400mm or less
Page 1 of 6 The LC6X4WTM Security Wall Mount with Tilt is designed to secure a flat screen, up to a 60", to the wall while still allowing the monitor to tilt. The VESA mounting patterns on the front of
More informationArticulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series)
P Articulating TV/Monitor Wall Mount Model: WA300S (Butterfly Series) Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Displays Model# Display size range IM760P, IM760P-S 32" to 71" (81 to 180 cm) IM760PU, IM760PU-S 32" to 65" (81 to 165 cm) This product
More informationEDGE2 DUAL MONITOR ARM
EDGE2 DUAL MONITOR ARM EDGE2 Rev A 2/17 Model EDGE2-SLV Model EDGE2-BLK Model EDGE2-WHT ASSEMBLY AND ADJUSTMENT EDGE2 DUAL MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning
More informationMWH INSTALLATION INSTRUCTIONS. Medium Flat Panel Wall Mount. Instrucciones de instalación Installationsanleitung Instruções de Instalação
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Medium Flat Panel
More informationPWR INSTALLATION INSTRUCTIONS. Large Flat Panel Wall Mount. Instrucciones de instalación Installationsanleitung Instruções de Instalação
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Large Flat Panel Wall
More informationInstallation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens
Installation and Assembly: In-wall Mount for 32" to 71" Flat Panel Screens Model# IM760P, IM760P-S IM760PU, IM760PU-S Screen size range 32" to 71" (81 to 180 cm) 32" to 60" (81 to 152 cm) IM760P IM760P-S
More informationAssembly Instructions for model: VMPR1
Assembly Instructions for model: VMPR1 Congratulations on your purchase! The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design
More informationUSE AND CARE GUIDE FIXED LED / LCD TV WALL MOUNT (UNIVERSAL MOUNTING PATTERN, FITS VESA
Item #302-080 Model #50710 USE ND CRE GUIDE FIXED LED / LCD TV WLL MOUNT (UNIVERSL MOUNTING PTTERN, FITS VES 100/200/300/400/600) Questions, problems, missing parts? Before returning to the store, call
More informationINSTALLATION INSTRUCTIONS. Mid-Size Table Mount MTSAV, -BV, -CV
INSTALLATION INSTRUCTIONS Mid-Size Table Mount AV, -BV, -CV AV, -BV, -CV Installation Instructions DISCLAIMER Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively,
More informationPSMH2682 INSTALLATION INSTRUCTIONS. Large Flat Panel Static Wall Mount. Instrucciones de instalación Installationsanleitung Instruções de Instalação
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Large Flat Panel Static
More informationSB-WM-ART2-L-BL SB-WM-ART2-XL-BL
SB-WM-ART2-L-BL SB-WM-ART2-XL-BL Weatherproof Universal Dual-Arm Articulating Mount for Large TVs INSTALLATION MANUAL WARNING The maximum weight of this wall mount is 150 lbs (68.04 kg). Use with heavier
More informationLC200WT Security Wall Mount with Tilt for up to 32" Flat Screens
Page 1 of 6 The LC200WT Security Wall Mount with Tilt is designed to secure up to a 32" flat panel monitor to the wall while still allowing the monitor to tilt. The VESA mounting patterns on the front
More informationTITAN2-EDGE Public Access Computer Station Dual Track
TITAN2-EDGE Public Access Computer Station Dual Track TITAN2-EDGE Rev A 6/17 Model TITAN2-EDGE ASSEMBLY AND ADJUSTMENT TITAN2-EDGE PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the
More informationPSMO2086 INSTALLATION INSTRUCTIONS. Outdoor Large Flat Panel Static Wall Mount
INSTALLATION INSTRUCTIONS [Landscape example] [Portrait example] Outdoor Large Flat Panel Static Wall Mount Spanish Product Description German Product Description Portuguese Product Description Italian
More informationPlanar FWMG-MXL INSTALLATION INSTRUCTIONS
Planar FWMG-MXL INSTALLATION INSTRUCTIONS Fixed Wall Mount for Ultra Large Displays 50-98 weighing less than 300 lbs. Part Number: 955-0217-00 Planar, A Leyard 1195 NW Compton Drive Beaverton, OR 97006
More information19 to 39 TV WALL MOUNT - FULL MOTION
19 to 39 TV WALL MOUNT - FULL MOTION RF-HTVMMAB For wood-stud and concrete wall installations Safety information and specifications...2 Tools needed...2 Package contents...3 Installation instructions...5
More informationFHB-3538/5538 INSTALLATION INSTRUCTIONS. Custom Interface Bracket. f de instalación Installationsanleitung Instruções de Instalação
INSTALLATION INSTRUCTIONS f de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Custom Interface Bracket Spanish
More informationModular Video Wall System with Push-to-Pop-out and Anti-Theft Features VW401P. User s Manual
Modular Video Wall System with Push-to-Pop-out and Anti-Theft Features Contents Weight Limit.... 2 Warning Statements.... 2 Installation Tools.... 3 Parts List... 4 Features.... 5 Installing the Mount....
More informationASSEMBLY AND ADJUSTMENT
EDGE MONITOR ARM EDGE Rev A 2/17 Model EDGE-SLV Model EDGE-BLK Model EDGE-WHT ASSEMBLY AND ADJUSTMENT EDGE MONITOR ARM PARTS AND TOOLS PLEASE REVIEW these instructions before beginning the assembly and
More informationPFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 160 lb. / 72.57 kg. Included Components Wall Mount (Qty 1) Extension Brackets (Qty 2) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationKSA1013 INSTALLATION INSTRUCTIONS. Laptop Tray Accessory. Instrucciones de instalación Installationsanleitung Instruções de Instalação
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Laptop Tray Accessory
More informationHITCH MOUNT BICYCLE CARRIER Model BC-102
HITCH MOUNT BICYCLE CARRIER Model BC-102 MAXIMUM LOADING CAPACITY 60 LBS Recommended Tools for Assembly: Open Wrench (2 pc.) Open Wrench (2 pc.) Open Wrench (2 pc.) Size=17mm Size=19mm Size=24mm Assembly
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Swingout Arm Model: AM300/AM300-B NORTH AMERICA 3130 East Miraloma Avenue Anaheim, CA 92806 USA USA and Canada Phone: 1.800.368.9700 Fax: 1.800.832.4888 Other Locations
More informationSERVICE MANUAL. SL236 Lift Weld Replacement. Lift Weldment Replacement
SERVICE MANUAL Lift Weldment Replacement Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description
More informationFHP INSTALLATION INSTRUCTIONS. Ceiling Mount
INSTALLATION INSTRUCTIONS Ceiling Mount Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description
More informationPWRSKU INSTALLATION INSTRUCTIONS. Large Flat Panel Steel Stud Wall Mount. Instrucciones de instalación Installationsanleitung Instruções de Instalação
INSTALLATION INSTRUCTIONS Instrucciones de instalación Installationsanleitung Instruções de Instalação Istruzioni di installazione Installatie-instructies Instructions d installation Large Flat Panel Steel
More informationInstallation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine
Installation Guide Installation Kit for Mounting Philips MP20/30/40/50 on Datex-Ohmeda Aisys Anesthesia Machine The purpose of this guide is to: 1. Describe mounting of Counterweight (page 2). 2. Describe
More informationNW2F8-12. Fixed Wall Racks INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Fixed Wall Racks Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationPreference Collection 5580 Treatment Console INSTALLATION GUIDE
Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury
More informationPHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns
PHTM200 - Phantom 200 Flat Screen Wall Mount with Wafer Thin Projection Fits Screens up to 50 lbs with 200mm Mounting Patterns Features: Durable high quality gloss black baked on powder coat finish Fits
More informationSAN213 Instruction Manual
SAN213 Instruction Manual Scan here to view product demo and install videos or visit san.us/105 Milestone AV Technologies 6436 City West Parkway Eden Prairie, MN 55344 USA Customer Service Americas: 800-359-5520
More informationINSTALLATION MANUAL PBC-UMS
INSTALLATION MANUAL. PBC-UMS Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 01 PBL-110 Projector Mount Page 2 Installation
More information