Universal Projector Ceiling Mount Model: DPM-45

Transcription

1

2 Universal Projector Ceiling Mount Model: DPM-45 Instruction Manual Images may different from actual product Disclaimer It is Dyconn s intention to have all the correct information represented within this manual. Although we try our best, Dyconn makes no claim that the information comprised herein covers all conditions or details in connection with installation or use of this product. Dyconn assumes no responsibility for accuracy or adequacy of information comprised in this document. The information comprised here is subject to change without notice or obligation of any kind. It is installer's responsibility to make sure all components are properly assembled and installed using the instructions provided. Severe personal injury and property damage can result from improper installation or assembly. If you do not follow the corresponding instructions can result in damage, destruction of equipment or voiding of factory warranty. Ensure ceiling can support the total weight capacity 44lbs (20kg) of projector and the universal ceiling mount. Exceeding weight capacities can result in severe personal injury or damage to equipment. All bolts and screws must be correctly used at the designated points in the installation instructions to prevent damage to the projector. Read the following warning before installing - Verify all parts are included. Do not install if the products or hardware is damage. Not all hardware included will be used. - Please contact a qualified installer - This product contain moving parts, Use with caution - This product contains small item, keep these items away from children - Do not exceed the maximum weight capacity for this product Specification Maximum Weight Capacity 44(LBS) / 20(KG) Page 2

3 Product Dimensions Tools required for installation Page 3

4 Supplied Parts ASSEMBLY and INSTALLATION INSPECT THE MOUNT COMPONENTS BEFORE ASSEMBLY 1. Carefully inspect/verify that all components are present. 2. If the mount/components are damaged or missing, please contact the company/seller of the product you purchased and report the issue. NOTE: Read all assembly instructions before starting the installation process. Page 4

5 Step 1 Installing the Ceiling Plate Drilling into electrical wires can cause death or serious personal injury! Always make certain area behind mounting area is free of electrical wires before drilling or installing. Improper installation can lead to projector mount falling causing severe personal injury or damage to equipment. It is installer s responsibility to make sure the combined weight of all components does not exceed weight capacity of 44lbs (20Kg). Do not install near air conditioner vents where there is excessive dust or smoke. Note: To determine require mounting location; ensure that knowing the projector lens distance to screen distance. Please see projector details specifications on determining the distance. Wood Ceiling Installation 1. Disassemble the Ceiling Plate Cover from Ceiling Plate (2) as shown. (See Figure 1-1) Figure Place the Ceiling Plate to wood ceiling at desired location, mark location with pencil. 3. Drill wood ceiling pilot hole of 7/32 (5mm), pilot drill depth of 3 (75mm) and ensure pilot hole are straight. 4. Insert Lag Bolt through Washer, Ceiling Plate and install into pilot hole. Repeat for remaining Lag Bolts. Select hardware that fits your application (See Figure 1-2). Tighten the Lag Bolt so the Ceiling Plate is secured to the wood ceiling. Do not over tighten the Lag Bolt. Plaster Ceiling Pilot Pilot Hole Size Pilot Drill Depth 7/32" 3 " 5mm 75mm Page 5

6 Figure Then, proceed to place the Ceiling Plate Cover onto the Mounted Ceiling Plate and press firmly on the cover to make sure it is in place. (See Figure 1-3) Figure 1-3 Page 6

7 Step 1 Installing the Ceiling Plate Drilling into electrical wires can cause death or serious personal injury! Always make certain area behind mounting area is free of electrical wires before drilling or installing. Improper installation can lead to projector mount falling causing severe personal injury or damage to equipment. It is installer s responsibility to make sure the combined weight of all components does not exceed weight capacity of 44lbs (20Kg). Do not install near air conditioner vents where there is excessive dust or smoke. Note: To determine require mounting location; ensure that knowing the projector lens distance to screen distance. Please see projector details specifications on determining the distance Masonry Installation 1. Disassemble the Ceiling Plate Cover from Ceiling Plate (2) as shown. (See Figure 1-4) Figure Attach the Ceiling Plate to masonry ceiling, mark the mounting location. Drill the masonry pilot hole of 3/8 (10mm), pilot drill depth of 3 (75mm) and ensure the pilot hole are straight and completely through the structural. Insert anchor into anchor hole and seat with gentle tapping from hammer. Anchor should be fully engaged into structural. Repeat for remaining anchor. 3. Insert Lag Bolt through Washer, Ceiling Plate (2) and install into pilot hole. Repeat for remaining Lag Bolts. Select hardware that fits your application (See Figure 1-5). Tighten the Lag Bolt so the Ceiling Plate is secured to the masonry ceiling. Do not over tighten the Lag Bolt. Page 7

8 Masonry Pilot Pilot Hole Size Pilot Drill Depth 3/8" 3 " 10mm 75mm Figure Then, proceed to place the Ceiling Plate Cover onto the Mounted Ceiling Plate and press firmly on the cover to make sure it is in place. (See Figure 1-6) Figure 1-6 Page 8

9 Step 2 Attaching the Ceiling Mount Assembly to Ceiling Plate 1. Remove the Projector Plate from the Ceiling Mount Assembly (1) as shown (See Figure 2-1) Figure Connect the Ceiling Mount Assembly Head to the Ceiling Plate. Secure the Ceiling Mount Assembly Head by turning the Ceiling Mount Assembly head in clockwise until tight. (See figure 2-2). 3. Tighten set screw using Allen Wrench 3mm (11) supplied. (See Figure 2-3) Figure 2-2 Figure 2-3 Page 9

10 Step 3 Finding Centre Gravity of the Projector 1. Pick up the projector using both of your index fingers. Move your fingers along the side of the projector until you find it is level. Repeat for perpendicular side on this process, where both balance point s meet is the center gravity of your projector. Use a pencil to mark on this point. (See Figure 3-1) Figure 3-1 Page 10

11 Step 4 Attaching Projector Plate to the Projector 1. Determine the diameter of the Leg Posts (4, 5, 6, or 7) your projector requires by hand threading them to the Projector. (See Figure 4-1) 2. Before you assembly the Projector Legs (10), ensure that the Leg Post must be firmly attached into Projector. Then, proceed to thread the Projector Legs 10 onto Leg Post as shown. (See Figure 4-2) Figure 4-1 Figure To make Projector Leg adjustments, loosen the screw with supplied Allen Wrench 4mm 12 and adjust to your desired position. Re-tighten the screw firmly. (See Figure 4-3) Figure 4-3 Page 11

12 4. Place the Projector Plate over the Projector Legs (10) and align the mounting holes as shown. Tighten Hex Screw M5x8mm using Allen Wrench 4mm supplied.(see Figure 4-4) Figure Once this is done, thread the Leg Post Cover (3) over Leg Post Assembly. (See Figure 4-5) Figure Connect the projector mount assembly to ceiling plate as shown. (See Figure 4-6) by insert the pin on the projector plate into the slot in the Ceiling Mount Assembly Head to lock the projector mount assembly. Figure 4-6 Page 12

13 7. Adjust and align the locking plate connector as shown. (See Figure 4-7) 8. Make sure locking plate connector holes are match up and aligned. Proceed to tighten the Ceiling Mount Assembly with Hex Screw M5x8mm using Allen Wrench 4mm (12) supplied. (See Figure 4-8) Figure 4-7 Figure 4-8 Page 13

14 Step 5 Adjusting the position of the Projector 1. This product is designed to adjust quickly and easily according to your needs. 2. Side ways pitch and the pitch angle up to 20 degrees. (See Figure 5-1) Figure To make rotate adjustment, ensure that the weight of the projector is supported. The product can reach 360 degrees rotation. (See Figure 5-2) Figure 5-2 Page 14

15 DYCONN PRODUCT WARRANTY To obtain warranty service, contact Dyconn customer service at (855) or visit Dyconn disclaims any liability for modification, improper installations, or installations over specified weight range. Dyconn will not be liable for any damages arising out of the use or inability to use Dyconn products. Warranty specification is subject to change without prior notice. Page 15