Installation Instructions
|
|
- Augustine Potter
- 5 years ago
- Views:
Transcription
1 Installation Instructions Feed Installation for 0.6m(2ft) Spread Spectrum Antennas Bulletin Revision F Antenna Assembly Sequence P2F/HP2F/PX2F/ HPX2F antenna a 1 Apply conductive grease (5) to screw threads and vertex plate spigot of feed assembly (See Warning) Antenna Description This antenna consists of a 0.6 metre (2ft) reflector, radome (if supplied), feed, and offset tower mount. The mount is designed to attach the antenna to a vertical tower pipe of diameter 115 mm (4.5"). The mount also provides adjustment ranges of ±5 elevation and ±5 azimuth. Notice The installation, maintenance, or removal of antenna systems requires qualified, experienced personnel. Andrew installation instructions have been written for such personnel. Antenna systems should be inspected once a year by qualified personnel to verify proper installation, maintenance, and condition of equipment. These antennas should be installed with jumpers from main coaxial feeder cable with appropriate strain relief. Andrew disclaims any liability or responsibility for the results of improper or unsafe installation practices. Fastener Table 1. Fastener Torque Specifications Torque value in N m (lb ft ) for each fastener size Size M4 M5 M6 M8 M10 M12 Stainless steel 1b 49/52 SERIES P2F-52/ P2F-49 SHOWN Feed mounting hole Apply conductive grease (20) to screw threads and vertex plate spigot of feed assembly (See Warning) Warning: Use protective wear to avoid skin contact with the conductive grease. Keep away from mouth. Wash thoroughly after use with liberal amounts of liquid soap and rinse with water. Do not store open near food or food sources. Contents: oil, clay, and zinc dust. Feed Antenna 57W SERIES P2F-57W SHOWN Feed mounting hole Index
2 2 Align Polerization Arrow "V" mark on Mounting Ring Align Polerization Arrow with "H" mark on Mounting Ring 3 P2F/HP2F-49/52-DET Antenna Vertical polarization P2F/HP2F-49/52-DET Antenna Horizontal polarization Note orientation of connectors. Vertical polarization connector must always point downward's Note orientation of connectors. Vertical polarization connector must always point downward's HPX2F/PX2F-49/52-DET Antenna Pipe Mount Right HPX2F/PX2F-49/52-DET Antenna Pipe Mount Left
3 4 Align Polerization Arrow with "H" mark on Mounting Ring Align Polerization Arrow "V" mark on Mounting Ring P2F/HP2F-57W-DET Antenna Horizontal polarization P2F/HP2F-57W-DET Antenna Vertical polarization Slacken bolts 1/2 turn to adjust azimuth (top & bottom) Rotate to adjust elevation Apply loctite(16) to threads before fitting to antenna 9 When fitting, torque nuts(10) to 22Nm (16.2lb-ft) Slacken bolts 1/2 turn to adjust elevation Rotate to adjust azimuth
4 7 P2F/PX2F-49/52-N7A Antenna with Feed and Mount Assembled 8 P2F/PX2F-57W-N7A Antenna with Feed and Mount Assembled
5 P2F/PX2F-49/52-NXA Antenna with Feed, Radome HP2F/HPX2F-49/52-NPA Antenna with Feed, Radome
6 P2F/PX2F-57W-NXA Antenna with Feed, Radome HP2F/HPX2F-57W-NPA Antenna with Feed, Radome
7 Table 2. Parts List Item Description Part No Qty Contained In 1 Feed Assembly * 1-2 M6 Hex Nut st steel Lock washer M6 st steel Washer M6 st steel Clamp Ring Soc Hd Cap Screw M5 st steel Feed Clip Mount Scr hex Soc C'sk M10 st steel Nut hex M10 st steel Lock washer M10 st steel Washer Large M10 st steel Radome see detail 1-14 Screw Hex Hd M6 st steel Lock washer M6 st steel Loctite Screw Pan Hd M6 st steel Lock Washer M6 st steel Washer M6 st steel conductive grease * Frequency dependent Hereby ANDREW, a Commscope Company, declares that this antenna is in compliance with the essential requirements of EU Directive 1999/5/EC. A copy of the Declaration of Conformance is available on Andrew Corporation West 153rd Street Orland Park, IL U.S. A Telephone: 708/ FAX (U.S.A.): 1-800/ TELEX: Customer Service, 24 hours: U.S.A. Canada Mexico: 1-800/ U.K.: Republic of Ireland: Other Europe: Printed in E.C. Feb'03 Copyright 1993 by Andrew Corporation
Installation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas.
Description The following pages show the steps required to assembly and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation
More informationInstruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev.
Instruction Sheet No. 412764 Rev. B ECO 12469 Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) These Installation Instructions are valid for antennas in the following version: reflector 2.4
More informationInstallation Instructions
903-CIS0143-C Installation Instructions 0.9m Antenna LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Torsgatan
More information2 Pipe Clamp Bracket 3 11 M6 Screw with Tube M6 Hex Nut 2 4 M20 Flat Washer 4
3842 Revision B, May 201 Mounting Kit, For Metro Cell Antennas MC-MNT-TOP-2 Mounting Kit GENERAL INFORMATION Top of pole mounting option Fits round members.3" to 8." (10 to 21 mm) pole diameter. PRE-INSTALLATION
More informationThese Installation Instructions are valid for antennas in the following version:
Installation Instructions 4 ft CompactLine Antennas (with E-Mount 200 km/h) SB, SBX NMT 480-12(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall be
More informationStandard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm)
495 R Billerica Ave. N. Billerica, MA 01862 USA Tel: (978) 459-8800 Fax: (978) 459-3310 / 8814 www.radiowavesinc.com email: sales@radiowavesinc.com Standard Pole Mount Parabolic Antenna Mounting Instructions
More informationThese Installation Instructions are valid for antennas in the following version :
Installation Instructions 2 ft Antennas (with M-Mount) SB, SBX (RFS CompactLine ) SP, SPF, SPX, SD, SDX, SU, SUX (RFS SlimLine ) PAL, DA, DAX, UA, UDA, UXA (Microwave) NMT 391-11(e) Antenna with integrated
More informationInstallation Instructions
Installation Instructions For 4 foot / 1.2m Diameter Ultra-high Performance Antenna Model ADxxG-4-T2 Before Installation, please read the instructions carefully. This instruction guide covers the installation
More informationInstallation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX
Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX NMT 553-01(e) These Installation Instructions are valid for antennas in the following version : Reflector Ø
More informationAntenna Installation Manual
High Performance Antennas 3 & 4 ft. (0.9 & 1.2 m) Antenna Installation Manual Please read the manual completely and carefully before installation. Instructions are intended for qualified and experienced
More informationTechnical publication. Path alignment and cross polarization procedure for parabolic microwave antennas
Technical publication Path alignment and cross polarization procedure for parabolic microwave antennas Contents 1.0 Introduction 3 2.0 Path alignment procedure 3 2.1 Setting azimuth marker 3 2.2 Test equipment
More informationPole Mount Installation Guide
Pole Mount Installation Guide (No Fine Adjustment) 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com IMPORTANT!
More information.84M Ku-Band Rx/O Antenna System
4096-644 Revision A May 9, 2003 ASSEMBLY MANUAL.84M Ku-Band Rx/O Antenna System PRODELIN CORPORATION 1500 PRODELIN DRIVE NEWTON, NC 28658 .84M Ku-Band Rx/O Antenna System A ORIGINAL RELEASE 5/9/2003 A.Hahn
More informationinstallation guide 1 GUIDE#: PWB-wwpontoon-pol-004
f250 pontoon WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This WakeWorks tower fits Pontoon boats with 96 to 102 inch wide beam widths. This measurement is taken from
More informationInstallation Instructions
Installation Instructions For 0.2m Ultra-high Performance Antenna Model ADxxG-0-T2 Before Installation, please read these instructions carefully. This instruction guide is for the installation of 8 inch
More informationcontained within this bulletin must always be followed and take precedence over any information contained within the video
Rev: K IMPORTANT! INSTALLATION READ THIS MANUAL FULLY BEFORE UNPACKING AND ASSEMBLING ANTENNA 1ft 2ft Videos provide supplementary information - the instructions contained within this bulletin must always
More information1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM
August 21, 1997 Revision D ASSEMBLY MANUAL 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM PRODELIN CORPORATION 1700 NE CABLE DRIVE CONOVER, NC 28613-0368 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM D
More informationRemarks: Before Installation, please read the instruction carefully.
30 cm antenna Z24A30T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.3m ultra-high performance microwave antenna. Installation,
More information6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT set by hand or by optional RCU (Remote Control Unit)
6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT R1 698 960 1710 2690 1710 2690 1.5 10 0 10 2 10 set by hand or by optional RCU (Remote Control Unit) X Y1 X Y2 65 65 65 X 6-Port
More informationANTENNA EXPERTS. Website: AP MHz. 2.4 Meters 30dBi. Gain
ANTENNA EXPERTS E-mail: info@antennaexperts.in Website: www.antennaexperts.in AP-180030 1700 1900 MHz. 2.4 Meters 30dBi. Gain INSTALLATION MANUAL GRID PARABOLIC ANTENNA NOTICE: Installation, maintenance
More informationInstallation Guide Flat Panel Antenna Mounting Kit For
Installation Guide Flat Panel Antenna Mounting Kit For 103670-1 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com
More informationRATCHET CABLE CUTTER
OPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 764 RATCHET CABLE CUTTER Read and understand this material before operating or servicing this equipment. Failure to understand how to safely operate this
More informationThis instruction manual contains all necessary information required to assist in the correct installation of ARGUS Stadium Panel Antennas.
Revision C, August 2016 Instruction Manual, Stadium Panel Antennas General This instruction manual contains all necessary information required to assist in the correct installation of ARGUS Stadium Panel
More informationMESA-HPX. Assembly and Installation Manual. w/appendix A for Prodelin Antenna. 901-Manual-MESA-HPX
MESA-HPX Assembly and Installation Manual w/appendix A for Prodelin Antenna 901-Manual-MESA-HPX Rev 30 March 2011 2 INDEX Installation Cautions 4 Installation Pole Height Orientation of the Mount on the
More information2-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT Enhanced Sidelobe Suppression
2-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT Enhanced Sidelobe Suppression 1710 2690 18 Downtilt set by hand or by optional RCU (Remote Control Unit) X 65 2 14 2-Port Antenna
More informationINSTALLATION INSTRUCTIONS, AND PARTS LIST
INSTALLATION INSTRUCTIONS, AND PARTS LIST LB20 SERIES RAMPS Link Mfg. Ltd. 223 15th St. N.E. Sioux Center, IA USA 51250-2120 (712) 722-4868 Fax (712) 722-4779 QUESTIONS? CALL CUSTOMER SERVICE 1-800-248-3057
More informationE4-WM5-Y525A00 MOUNTING INSTRUCTION
RAM 2500/3500 4WD B8 5100 (Dual Steering Damper Kit) The installation of these steering dampers must be performed only by experienced and qualified personnel. Read and follow the installation instructions
More informationMM22 Enclosure Mount C228M-B (4/14)
I N S T A L L A T I O N MM22 Enclosure Mount C228M-B (4/14) Important Safety Instructions 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes.
More information4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
4-Port Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 790 960 0 10 2 8 set by hand or by optional RCU (Remote Control Unit) X 65 Y1 1710 2690 X 65 4-Port Antenna 790 960/1710 2690
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More informationModel 6025 Single-Boom
Log Periodic FM Broadcast Antenna Model 6025 Single-Boom Instruction Manual Installation, Operation, & Maintenance Congratulations! Thank you for purchasing one of the finest FM broadcast antennas on the
More informationDownload and read the Technical Description and Installation guide before deploying the PTP 820C equipment.
User Documentation Installation and operation of the PTP 820C is described in the PTP 820C Technical Description and PTP 820C Installation Guide available for download from: http://www.cambiumnetworks.com/support
More informationInstruction Manual for 98cm Elliptical Ka Antenna
Instruction Manual for 98cm Elliptical Ka Antenna 98cm WB Issue 03 Caution This instruction leaflet will assist you in the correct installation of the product. Read it prior to starting any installation
More informationInstallation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna
Release 3.0 NN47251-311 Issue 02.01 June 2014 Installation Job Aid (English) for Avaya WLAN 8100 series- WLAN AP 8120 with External Antenna How to get help To access the complete range of services and
More informationKU-BAND FEED INSTALLATION OMT INTERFACE
Revision D April 22, 2016 Assembly Manual KU-BAND FEED INSTALLATION OMT INTERFACE General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com KU-BAND
More information4-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
4-Port Antenna Frequency Range Dual Polarization HPB Adjust. Electr. DT R1 790 960 0.5 9.5 0 6 set by hand or by optional RCU (Remote Control Unit) X 65 B1 1710 2180 X 65 4-Port Antenna 790 960/1710 2180
More informationFoundation Specifications for 5.6-Meter Modular Earth Station Antennas
Installation Instructions Bulletin 237029 Foundation Specifications for 5.6-Meter Modular Earth Station Antennas Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationMTS-SP100. RENOGY Pole Mount System E Philadelphia St, Ontario, CA Version: 1.2
MTS-SP100 RENOGY Pole Mount System 2775 E Philadelphia St, Ontario, CA 91761 1-800-330-8678 1 Version: 1.2 Important Safety Instructions Please save these instructions. This manual contains important safety,
More informationFoundation Specifications for 7.6-Meter Modular Earth Station Antennas
Installation Instructions Foundation Specifications for 7.6-Meter Modular Earth Station Antennas Bulletin 237186A Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationRemarks: Before Installation, please read the instruction carefully.
60 cm antenna Z24A60T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.6m ultra-high performance microwave antenna. Installation,
More informationC-15 Truck Engine 9NZ00001-UP(SEBP ) - Document Structure. Media Number -RENR Publication Date -01/07/2008 Date Updated -22/07/2008
Page 1 of 8 Shutdown SIS Previous Screen Product: TRUCK ENGINE Model: C-15 TRUCK ENGINE 9NZ Configuration: C-15 Truck Engine 9NZ00001-UP Disassembly and Assembly C-15, C-16 and C-18 Truck Engines Media
More informationAGILITY. ROTA WEB CLIMBER 3.3m PROD. CODE SIZE AGE RANGE F/ FALL HEIGHT HEAVIEST PART TOTAL WEIGHT ROTAWEB33. 8 TO mm 73kg 115kg
AGILITY ROTA WEB CLIMBER.m PROD. CODE SIZE AGE RANGE F/ FALL HEIGHT HEAVIEST PART TOTAL WEIGHT Dia. m x.m High 8 TO 4 00mm 7kg 5kg SPECIFICATION Centre Upright: Made from 6" diameter aluminium tube to
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More information1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM
August12, 2003 ASSEMBLY MANUAL Revision E 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM E Revised
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ROCK SLIDERS APPLICATION: 2007-2017 Jeep Wrangler JK 2 Door PART NUMBER: 42-7005 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 ROCK SLIDER ASSEMBLY, DRIVER
More informationH8508 Impact Wrench SERVICE MANUAL. Model (Serial Code FWN) Model (Serial Code FWP)
SERVICE MANUAL H8508 Impact Wrench Model 48755 (Serial Code FWN) Model 48760 (Serial Code FWP) Read and understand all of the instructions and safety information in this manual before operating or servicing
More informationINSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011
INSTALLATION INSTRUCTIONS Y-Connector Accessory (For Multi-Dual Arm Mounting Systems) Model: KSA-1011 Specifications: Installs to K-Series desk or wall mount. Accommodates K-Series mounting arms (fixed
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationDO35 MAINTENANCE INSTRUCTIONS
CUSTOMER INFORMATION SHEET NO. 038 DO35 MAINTENANCE INSTRUCTIONS (DO35 V3 LAUNCHED PRODUCTION JUNE 2017) Table of Contents 1.0 Replacing Spindle Bushes V3... 22 2.0 Replacing Locking Mechanism V3... 6
More informationinstallation guide 1 GUIDE#: pwb-assault-004
assault WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More informationOPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 1813 BENDING TABLE FOR 881 HYDRAULIC BENDER
OPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 1813 BENDING TABLE FOR 881 HYDRAULIC BENDER Read and understand this material before operating or servicing this bender. Failure to understand how to safely
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SNYPER TUBULAR FENDERS APPLICATION: 2007-2017 Jeep Wrangler JK PART NUMBER: 62-1005, 62-1015 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1,2 2 FRONT FENDERS, DRIVER (1) AND PASSENGER
More informationDUAL ADJUSTABLE PULLEY IP-D9302 INSTALLATION INSTRUCTIONS
DUAL ADJUSTABLE PULLEY IP-D9302 INSTALLATION INSTRUCTIONS Copyright 2010. Star Trac by Core Industries, Inc. All rights reserved, including those to reproduce this book or parts thereof in any form without
More information.98M Ku-BAND Rx/Tx ANTENNA SYSTEM
Revision C January 2, 2002 ASSEMBLY MANUAL ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 ANTENNA SYSTEM C Revised Series text B Revised Address 1/2/02 RAH A Revise and Update
More informationC a r r i a g e A s s e m b l y R e p l a c e m e n t
E1 TF-CR C a r r i a g e A s s e m b l y R e p l a c e m e n t October 2007 Software Version 5.0 and higher IMPORTANT! TigerStop must be enabled with a code that must be obtained from TigerStop Customer
More informationinstallation guide 1 GUIDE#: pwb-assault-001
assault WAKEBOARD tower installation guide INSTALLATION SUPPORT 1 important information This Aerial wakeboard tower fits motor boats with 76-108 inch wide beam widths. This measurement is taken from the
More information1.8 METER SERIES 1184 ANTENNA SYSTEM
REVISION F January 10, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1184 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1184 ANTENNA SYSTEM F Revised Address 1/10/02
More informationMPA-9000 Universal Ceiling Projector Mount Kit
I N S T R U C T I O N M A N U A L Universal Ceiling Projector Mount Kit The Universal Ceiling Projector Mount provides a unique, simplified method of ceiling mounting your inverted projector. This low
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type D
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type D ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 060712-7 Side-of-Pole Mount for 4 Modules (SPM4) For Module Type
More informationRhino SD2/XD2 Mini Tote Conversion Kit
Instruction Sheet P/N 1613210 01 Description See Figure 1. The Rhino SD2/XD2 mini tote conversion kit is used when the material container includes a follower as part of the container structure. The mini
More informationSTANDARD MICROWAVE COMBINER MODEL SMC-XX-X-HP-X
SMC-XX-X-HP Standard Microwave Combiner STANDARD MICROWAVE COMBINER MODEL SMC-XX-X-HP-X Installation Manual Please read the manual completely and carefully before installation. Instructions are intended
More informationMounting and Alignment Overview
CHAPTER 3 This chapter provides an overview of bridge mounting and antenna alignment. The following sections are included in this chapter: Mounting the Bridge, page 3-2 Mounting Hardware, page 3-2 Bridge
More informationFoundation Specifications for Type ES45T-T and ES45T-R 4.5-Meter Earth Station Antennas
Installation Instructions Foundation Specifications for Type ES45T-T and ES45T-R 4.5-Meter Earth Station Antennas Bulletin 37690B Revision F 1.0 INTRODUCTION 1.1 This document specifies typical foundation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SPORTSMAN WINCH MOUNT GRILLE GUARD APPLICATION: 2016-2018 Toyota Tacoma PART NUMBER: 40-93885, 45-93880, 46-23885 ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 WINCH TRAY 15MM SOCKET
More information1904, 1904Pg, 1904PgSB, and 1906SB High Capacity Ratchet Knockout Drivers
INSTRUCTION MANUAL 1904, 1904Pg, 1904PgSB, and 1906SB High Capacity Ratchet Knockout Drivers Read and understand all of the instructions and safety information in this manual before operating or servicing
More informationCaliper Brake WINDCAL 90
Caliper Brake WINDCAL 90 (i) FORM NO. L-20233-A-0601 In accordance with Nexen s established policy of constant product improvement, the specifications contained in this manual are subject to change without
More informationTAILGATE SPREADER MATERIAL SAVER SYSTEM INSTALLATION & OPERATION MANUAL (TGS 300, TGS 600, & TGS 1100) TGS11328
TAILGATE SPREADER MATERIAL SAVER SYSTEM INSTALLATION & OPERATION MANUAL (TGS 300, TGS 600, & TGS 1100) TGS11328 TABLE OF CONTENTS WARNINGS & CAUTIONS... 2 MATERIAL SAVER SYSTEM PARTS LIST... 3 EXISTING
More informationCRITICAL INFORMATION:
IMPORTANT ALERT: GM uses a very strong thread-locking compound on all body bolts. Use of an air assisted impact ratchet can cause damage to the threads on factory body mount bolts and the internal nut
More informationSide-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation
Side-of-Pole Mount for 4 Modules (SPM4) For Module Type B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3358-2 PCN 060712-5 Side-of-Pole Mount for 4 Modules (SPM4) For
More informationH4670/42192 Submersible Trash Pump
SERVICE MANUAL H4670/42192 Submersible Trash Pump Serial Code GLW Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 99916070 REV
More informationModel DB Disc Caliper Brake AIR CHAMP PRODUCTS. User Manual. (i) MTY (81)
DIST. AUTORIZADO MEX (55) 53 63 3 3 QRO (44) 95 7 60 MTY (8) 83 54 0 8 AIR CHAMP PRODUCTS User Manual Model DB Disc Caliper Brake (i) FORM NO. L-00-G-030 MEX (55) 53 63 3 3 MTY (8) 83 54 0 8 DIST. AUTORIZADO
More informationCP6 6 Band Trap Vertical 80-6m
CP6 6 Band Trap Vertical 80-6m Instruction Sheet The CP6 is a multi-band trap-vertical antenna for HF bands, covering the 80*, 40, 20, 15, 10m & 6m amateur bands. Made from heavy duty aluminum, the CP6
More informationInstallation Instructions: Bumper (Part # SB76850) XJ Jeep Cherokee XRC Rear Bumper
NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included Qty 93-7789 XJ XRC 1 93-7807 Bumper Mount Bracket: Drvr 1 93-7811 Bumper Mount Bracket: Pass 1
More informationParadigm. Connect100 Installation Guide
Paradigm GX Connect100 Installation Guide Paradigm GX Safe Use WARNING Radiation Hazard. Transmitter power levels are sufficient to cause blindness or other serious injury to body tissue. Do not power
More informationType XTSR71 Sizes
(Page 1 of 13) s 494-5258 Type XTSR71 s 494-5258 Figure 1 Thomas XTSR71 Coupling 1. General Information 1.1 Thomas Couplings are designed to provide a mechanical connection between the rotating shafts
More informationFortress Fe Posts must always be secured to the deck framing. Fortress Fe Posts should never be attached to only the deck boards.
Installation Instructions for Fortress Vertical Cable Panel System with Brackets and Fe Posts It is the responsibility of the installer to meet all code and safety requirements, and to obtain all required
More information1.8 METER SERIES 1194 ANTENNA SYSTEM
January 14, 2002 REVISION G ASSEMBLY MANUAL 1.8 METER SERIES 1194 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1194 ANTENNA SYSTEM G Revise Address 1/14/02 F
More informationCopyright 2005 Valmont Industries, Inc.
Hose Drag TOPIVIEW OF CART Universal 1 Left Guidance Support (4" H.D.) 1732080... Left Guidance Sumort.. 16". H.D.)... 1732138 2 Right Guidance Support (4" H.D.)... 1732081 Right Guidance Support (6" H.D.)...
More informationSingle and Double Gates Operation & Maintenance Manual
R E L I A B L E S A F E A C C E S S Single and Double Gates Operation & Maintenance Manual 2 System Overview SAFETY GATES KEE GATE is a complete range of safety gates designed specifically to provide permanent
More information6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT
6-Port Antenna Frequency Range Dual Polarization HPBW Adjust. Electr. DT R1 1710 1880 0 10 0 6 0 6 set by hand or by optional RCU (Remote Control Unit) B1 B2 1920 2170 6-Port Antenna /1710 1880/1920 2170
More informationLab Style Table Frame Part No Assembly Guide Automation Technology
Ergonomic Workstations Lab Style Table Frame Part No. 8 0 Assembly Guide 7 90 70 Automation Technology SPECIFICATIONS Lab style frame part number... 80 Height... 70 mm (8.") Width... 90 mm (.7") Depth...
More informationBeam and Purlin Clamps Beam Clamps
Metal Framing & Cable Tray Steel City Hangers, Clamps & Fasteners Beam and Purlin Clamps Beam Clamps Fits beam flanges to 2" Supports 4" and 8" threaded rod, S-hooks, electrical boxes, conduit and bridle
More informationM2 Antenna Systems, Inc. Model No: 2M5WL
M2 Antenna Systems, Inc. Model No: 2M5WL SPECIFICATIONS: Model... 2M5WL Frequency Range... 144 To 148 MHz *Gain... 16.84 dbi Front to back... 22 db Typical Beamwidth... E=26 H=29 Feed type... T Match Feed
More information1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM
REVISION H April 20, 2016 ASSEMBLY MANUAL 1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com 1.2
More informationM2 Antenna Systems, Inc. Model No: 2M4
M2 Antenna Systems, Inc. Model No: 2M4 SPECIFICATIONS: Model... 2M4 Frequency Range... 144 To 148 MHz *Gain... 9.6 dbi Front to back... 20 db Typical Beamwidth... E=54 H=74 Feed type... T Match Feed Impedance....
More information32 Gallon Perforated Square Receptacle
32 Gallon Perforated Square Receptacle 992-031 24 5/" 24 5/" 39 1/2" 30 1/2" ITEM NO. PART NUMBER DESCRIPTION QTY. 1 653-006 Receptacle Base 1 2 653-045 32 Gallon Perforated Side 4 3 653-011 Arch Lid 1
More informationEngineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard
Engineering Data Single Reduction Parts List Item # Description Basic Single Reduction Unit 1. Gear Housing 2. Pipe Plug 3. Vent Plug 4. Splash Guard 5. Input Cover 6. O-Ring 7. Hex Head Cap Screw 8. Input
More informationSingle and Double Gates Operation & Maintenance Manual
R E L I A B L E S A F E A C C E S S Single and Double Gates Operation & Maintenance Manual System Overview SAFETY GATES KEE GATE is a complete range of safety gates designed specifically to provide permanent
More informationH6400, H6400C1 & VSD6400 REVERSIBLE DRILLS
SERVICE MANUAL H6400, H6400C1 & VSD6400 REVERSIBLE DRILLS Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 999 1801.3 REV 4 2001
More informationCisco Aironet 2.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT2588P3M-N)
Cisco Aironet.4-GHz/5-GHz 8-dBi Directional Antenna (AIR-ANT588P3M-N) This document outlines the specifications for the Cisco Aironet AIR-ANT588P3M-N.4/5-GHz 8-dBi 3-Port Directional Antenna with N-connectors
More informationThomas Disc Couplings Installation and Maintenance Series 71-8 Sizes (Page 1 of 10) DANGER!
Thomas Disc s Installation and Maintenance Series 71-8 s 225-750 (Page 1 of 10) This is the Original Document in English Language Figure 1-1. General Information Thomas Series 71-8 1.1. Thomas Series 71-8
More informationSwivel Hoist Ring Page 142
Swivel Hoist Ring Page 142 Hoist Rings Color coded to distinguish between UNC (Red) and Metric (Silver) thread types HR-125 M HR-125 Available in UNC and Metric thread sizes. UNC threads available in sizes
More informationInstruction and Assembly Manual 1 - Compass 1 - Clinometer 1-9 Magnetic Bubble Level 1 - Torque Wrench (Capacity 4 Ft-lbs Ft-lbs)
Instruction and Assembly Manual 1 - Compass 1 - Clinometer 1-9 Magnetic Bubble Level 1 - Torque Wrench (Capacity 4 Ft-lbs - 175 Ft-lbs) ASSEMBLY TOOLS REQUIRED 1 - ¹⁵ ₁₆ Deep Socket (¹ ₂ Drive) 1 - ⁷ ₁₆
More informationM2 Antenna Systems, Inc. Model No: YAGI ANTENNA
M Antenna Systems, Inc. Model No: 4.5-7 YAGI ANTENNA SPECIFICATIONS: Model... 4.5-7 Frequency Range... 4.0 To 4.5 MHz *Gain... 0 To 7 dbi Front to back... 0 db over the rear 80 Beamwidth... E=44 H=50 typical
More informationIF YOU DO NOT KNOW WHAT YOU ARE DOING, DO NOT DO IT!
TWIN CAM Alpha & Beta Case Boring Tool The JIMS Twin Cam Case Boring Tool takes all the guess work out of boring Twin Cam engine cases to accept JIMS 4" bore cylinders, 100 big bore kit, and 113" and 116"
More informationM4 Hex Nut [ ] M4 T-Nut 20 [20-044] Appx. 1. 3mm. 20 Series profiles (1 per hole) (1 per hole) Ordering Information
Handles & Light Duty PA 20 1 Assembly of Hinge M4x8 FHCS [24-208-4] M4 T-Nut 20 [20-044] M4 Hex Nut [24-706-4] 60 300-0 PA 20 on panel 2 Hinge positions 3-4 Clearance dimensions 5 Range of swing FOR M4
More information**MOUNTING YOUR MONITOR
FPP72V200 72 FREE STANDING DISPLAY CART Assembly Instructions Hardware List Ref. Qty. Part No. Description AA 4 030-1128 1/4-20 UNC, 1 3/4 Socket Hd Screws BB 1 030-1129 5/8-11 UNC 1 3/4 Socket Hd Screw
More informationSwivel Hoist Ring RIGGING ACCESSORIES. Color coded to distinguish between UNC (Red) and Metric (Silver) thread types.
RIGGING ACCESSORIES Color coded to distinguish between UNC (Red) and Metric (Silver) thread types. Available in UNC and Metric thread sizes. UNC threads available in sizes from 800 pounds to 100,000 pounds,
More informationCisco Aironet Six-Element Dual-Band MIMO Patch Array Antenna (AIR-ANT25137NP-R)
Cisco Aironet Six-Element Dual-Band MIMO Patch Array Antenna (AIR-ANT25137NP-R) August 2, 2013 This document describes the AIR-ANT25137NP-R antenna and provides instructions for mounting it. The antenna
More informationINSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500
INSTALLATION INSTRUCTIONS 225019 / 225019-2 2010 DODGE RAM CREW CAB 2500/3500 PARTS LIST: Qty Description Qty Description 1 Driver/Left Side Bar 4 Plastic Square Retainer 1 Side Bar 2 12mm x 120mm Hex
More information