eguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards
|
|
- Edward Lang
- 6 years ago
- Views:
Transcription
1 eguard EG2233, EG3333, EG3355, EG3388 & EG8406: Installation and Set-up Procedures Tx 2200 and Rx 4200 Boards A. Primary Technical Data: Transmitter Operating voltage DC 24V Operating current. < 450mA Fuse 250V, 500mA Centre frequency /- 0.05MHz Modulation frequency..180hz, 172Hz, 160Hz or 150Hz (factory setting at 180Hz) Receiver Operating voltage.. DC 24V Operating current, stand-by < 300mA Operating current, operating.. < 400mA Fuse 250V, 500mA B. Step by Step Approach: General 1. Request for independent power supply for EAS usage. 2. Connect cable between antennas and test performance before affixing permanently. Often by moving the antenna a few 10~30cm may eliminate noise e.g. too close to metal wall. Sometimes, switching the position of Tx and Rx antennae may also improve operation. 3. Only the antenna wire needed to be grounded to the base of the antenna. Do not ground the power cable to the antenna as this will cause unnecessary interference. Tx antenna 1. This is the antenna with no LED at the base panel and no red light on top of the antenna. In multiple connection, must set one as Master and the rest as Slave. 2. Check that there are no interference along the power line and no hard tags or labels within close proximity of the antennae. 3. Normally no adjustments required on Tx but can check factory setting by using EG898 EAS Tester (if EAS Tester not available, see appendix 1for using oscilloscope):- The Tester will only work on Transmission antenna. Place the Tester as shown and press button. Three readings will show:- Fc (center of frequency) should read 8.15~8.25MHz Fs (modulation frequency) should read 180Hz Sw (sweep frequency) should read 1000k +/- 50
2 4. If there are high interference (refer to Rx antenna) and hard tags only are used, may adjust VR14 anti-clockwise to reduce f to 700. Note: in no circumstances should this be less than Fine tune Fc (center of frequency) by adjusting VR15, normally, this would not be required. 6. If there are other 8.2MHz system within 20m and synchronization is not possible, it will be necessary to change modulation frequency to 150Hz to avoid interference between systems. Modulation frequency at Rx board must also adjust to the same frequency. i. There are four jumpers with corresponding modulation frequency written on it. ii. Factory setting is at 180Hz on the far right. iii. 150Hz is on the far left. VR15 JP1 TP4, GND3 VR14 7. If there are systems very close to each other (next door) and cannot be synchronized, it will be necessary to change Fc to 9.5MHz or 10MHz to avoid interference. Follow the instructions on the board in jumpers JP4 and JP9. Note setting in EG3355 is different to other models. After changing, the Fc reading in the Tester will also change. Instructions JP4 and JP9 jumpers TP6 and GND2 8. However, with this change, it is also necessary to change hard tags/labels from 8.2 to 9.5 or 10MHz.
3 Rx antenna 1. Receiver Antenna (with red light on top of the antenna). Green lights: DS1, DS2 and DS3 Red lights: alarm 2. Check lights on DS1, DS2 and DS3. (i) No lights indicate best condition. (ii) If DS1 light flashes only, the system can still operate properly. (iii) If DS2 light lit up, turn VR1 anti-clockwise to until only DS1 light flashes. (iii) If all DS1, DS2 and DS3 lit up, strong interference. If after turning VR1 more than 5 turns and no improvement on DS lights, then must consider other solutions. 3. Other solutions, refer to steps in 3, 4, 5 and 6 in Tx Antenna section. 4. Ensure the SW1-2 and SW1-3 switches matches the modulation frequency set up in the Tx board. At factory setting of 180Hz, the SW1-2 and SW1-3 position is in ON. See instruction printed in the Rx board and as shown below:- 5. If there are occasional false alarms, may reduce the sensitivity of the system by adjusting SW1-4 and SW1-5 as shown above. 6. After changes made to SW, must press RESET.
4 7. Other functions: RF Labels and Hard Tags Selector Labels generally has a lower Q factor than hard tags thus if only hard tags are used, the system can be adjusted to increase its detection rate. SW1-1 ON Labels and Hard tags SW1-1 OFF Hard tags only (factory setting) Timing of Alarm and Warning Light Adjust VR2 (clockwise to extend, anti-clockwise to reduce) for alarm and light on time varying 1~4 seconds. JP3 1&2 Alarm and light on/off simultaneously JP3 2&3 Light will remain on for 2~3 seconds after alarm Alarm Volume Control Turn VR4 clockwise to increase loudness of alarm. Turn VR4 anti-clockwise to decrease loudness of alarm. VR4 is positioned below VR2 towards the bottom left hand corner of the Receiver Board. C. Trouble shooting High Interference If there were high interference, the system will shut itself off to avoid false alarm. To ensure the system will operate well, must try and eliminate obvious cause of interference. Then, follow the below instructions:- 1. In Tx, adjust VR14 until Sw reads 700 ~ In Rx, change jumper in JP1, moving one slot to the right i.e. from position 1/2 to 2/3. This is the case when there is high noise interference and detection distance is more than 1.5m. 3. In Rx, change jumper in JP2, moving one slot left i.e. from position 2/3 to ½. This is to eliminate the self-locking function at high noise interference. 4. In Rx, adjust VR1 until only DS1 light flashes. 5. In Rx, select SW1-4 to ON and SW1-5 to OFF. 6. Press RESET. If there is large metal objects close-by, may see if grounding it to the Rx antenna base labeled GND at P1 (connecting with wire) will improve interference. If no improvement, remove this grounding.
5 D. Multiple Connection: In multiple connection, JP2 and JP3 in the Master Tx Board should be set in position 1&2 (M) while P3 and P4 are the output connectors for multiple connections. In the Slave Tx Board, JP2 and JP3 should be set in position 2&3 (S) and P2 is for input while P3 and P4 are for output. See figure 1. Figure 1 - Multiple Connections: T2200 Slave T2200 Master JP2, JP3 in 1 & 2 position Change slave setting in respectively (factory setting). JP2, JP3 to 2 & 3 position P3 P3 Connect to Connect to another another slave slave via P2. Figure 2 Tx Board TP6, GND 2 P6 DC24V wiring to one or two Rx PCB at P1. Note +ve and -ve input. JP1 TP4, GND 3 Grounding to base P1 Power Supply cabling
6 Figure 3 Rx Board JP2 Grounding to base P1 DC24V wiring from Tx PCB (P6). Quick Checklist 1. Please see details and drawings above for full description and troubleshoot. 2. There are power in both Tx and Rx boards. If not check power supply and fuse in each Tx and Rx PCB. Replace fuse if necessary. 3. Check settings in Tx PCB using EAS Tester. 4. Ensure Fc, Fs and Sw readings are correct. Reduce Sw if there are high interference. 5. Ensure modulation frequency setting in Rx is same as that is Tx. 6. Adjust VR1 in Rx until only DS1 light flashes. 7. Press RESET in Rx after each change of SW switches.
7 Appendix 1 Transmitter PCB Checking Fc (center of frequency) using oscilloscope Connect oscilloscope probe to TP6 with grounding at GND2. Tune VR15 for adjustment. Checking Sw (sweep frequency) using oscilloscope 1. Disconnect antenna wire at P5. 2. Reset JP1 from 1&2 position to 2 &3. 3. Connect oscilloscope probe to TP4 with grounding at GND3. Tune VR14 for adjustment. Reading in oscilloscope of 0.65Vp-p is equivalent to 1000k. Reading in oscilloscope of 0.40Vp-p is equivalent to 700k. The system will not function if readying is lower than 0.40Vp-p. 4. Reset JP1 to position 1&2. 5. Reconnect antenna wire at P5.
58Khz ACOUSTO MAGNETIC SYSTEMS WIRING HANDBOOK
58Khz ACOUSTO MAGNETIC SYSTEMS WIRING HANDBOOK E.A.S. SISTEMAS ANTIHURTO, S.L. 1 Revisión 1 06/2012 1. INTRODUCTION. 2. SYSTEM DESCRIPTION. a. TRANSMITER ANTENNA TX. b. RECEIVER ANTENNA RX. c. POWER SUPPLY.
More informationUSER MANUAL. MetalSpy. EAS Add-On Technology for Foil Bag Protection
USER MANUAL MetalSpy EAS Add-On Technology for Foil Bag Protection 21 June 2011 Contents 1.0 SPECIFICATIONS & FEATURES... 3 1.1 System... 3 1.2 MetalSpy Diamond... 4 2.0 PCB CONNECTION... 4 2.1 MetalSpy
More informationYaskawa Electric America Unit Troubleshooting Manual Section Two: Power Checks GPD 506/P5 and GPD 515/G5 (0.4 ~ 160kW)
Yaskawa Electric America Unit Troubleshooting Manual Section Two: Power Checks GPD 506/P5 and GPD 515/G5 (0.4 ~ 160kW) Page 1 Section Two: Power Checks Page 2 Check box when completed Power Checks TEST
More informationRadio Control Installation and Operating Instructions System 4
Radio Control Installation and Operating Instructions System 4 P.O. Box 403, One Cedar Parkway, Jackson, WI 53037 Phone: 800-628-1909 Fax: 262-677-2058 Revision: April 19, 2012 Contents Introduction 3
More informationMRW 50, MRW 100, MRW 200. External Protection Barrier. Quick Installation Guide
MRW 50, MRW 100, MRW 200 External Protection Barrier Quick Installation Guide Version 1.1, October 2004 Copyright 2004 GE Interlogix B.V.. All rights reserved. GE Interlogix B.V. grants the right to reprint
More informationTVP2 PERFORMANCE TEST TAG MANUAL
TVP2 PERFORMANCE TEST TAG MANUAL Identec Ltd Mercantile Road Rainton Bridge Industrial Estate Houghton-Le-Spring County Durham England DH4 5PH Tel: +44 (0)191 584 4084 Fax: +44 (0)191 584 9077 www.identec.com
More informationRF Remote Control Unit SEAV
RF Remote Control Unit SEAV for LINAK TECH-systems Installation instructions Foreword Dear producer, Thank you for choosing an actuator system from LINAK. LINAK systems consist of high-tech products based
More informationProduct Manual RF Mono System
Product Manual RF Mono System 1 Table of contents 1. Technical Specification...4 2. Parameter Setting...5 2.1 Circuit Board Description...5 2.2 Position of the Jumpers on the Circuit Board...6 2.3 Connector
More informationPRO Professional Radio Control Series Applications
204 205 Ready to Use Remote Control 4, 8/16 Channel Systems Range: Up to 200 metres at 433MHz Up to 1,000 metres at 433MHz NB Relay Outputs: Momentary, Latching, Timed Receiver IP65 Applications Lighting
More information2.4GHZ WIRELESS SYSTEM FOR POLICE VIDEO RECORDING
PW24-2 2.4GHZ WIRELESS SYSTEM FOR POLICE VIDEO RECORDING USER GUIDE Revision B Page 1 of 8 10/11/06 TABLE OF CONTENTS 1. Quick Set Up and Operation... 3 2. Installation... 4 3. Guidelines For Best Performance...
More informationAudio Specialties Group Products Division MAS-101 UHF Receive Antenna Combiner Operators Guide
Audio Specialties Group Products Division MAS-101 UHF Receive Antenna Combiner Operators Guide REV-4 TABLE OF CONTENTS SECTION 1:... 3 1.0 Introduction... 3 SECTION 2:... 3 Features... 3 2.1 Standard Configurations...
More informationReceiver Adjustments
! -8-4!5 This Section details procedures for tuning and adjustment of T2000 series II radios. This is normally only required during product manufacture or after major servicing. The following topics are
More informationRF4432 wireless transceiver module
1. Description www.nicerf.com RF4432 RF4432 wireless transceiver module RF4432 adopts Silicon Lab Si4432 RF chip, which is a highly integrated wireless ISM band transceiver. The features of high sensitivity
More informationAlpha 3000 I n d u s t r i a l R a d i o R e m o t e C o n t r o l S y s t e m Operation & Parts Manual
Alpha 3000 I n d u s t r i a l R a d i o R e m o t e C o n t r o l S y s t e m Operation & Parts Manual Williams USA, LLC 38113 Plymouth Rd., Livonia, Michigan 48150 Phone: 1-734-416-5520, Fax: 1-734-416-1907
More informationThe University of Jordan Mechatronics Engineering Department Electronics Lab.( ) Experiment 1: Lab Equipment Familiarization
The University of Jordan Mechatronics Engineering Department Electronics Lab.(0908322) Experiment 1: Lab Equipment Familiarization Objectives To be familiar with the main blocks of the oscilloscope and
More informationTRC EV DR TRC EV DR TRC EV
DR-TRC103-EV Evaluation Kit User s Guide DR TRC103 868 EV DR TRC103 915 EV DR TRC103 950 EV DR-TRC103-EV User s Guide (2015/04/17) Page 1 of 11 www.murata.com Introduction The DR TRC103 series evaluation
More informationWPR400 Wireless Portable Reader
P516-098 WPR400 Wireless Portable Reader User guide Para el idioma español, navegue hacia www.schlage.com/support. Pour la portion française, veuillez consulter le site www.schlage.com/support. Contents
More informationVBRC 4. Radio Communicator. Installer Manual
VBRC 4 Radio Communicator Installer Manual 17 December 2014 CONTENT 1. INTRODUCTION...3 2. SYSTEM STRUCTURE...3 3. SYSTEM PROGRAMMING WITH PC SOFTWARE...5 4. TROUBLESHOOTING...6 5. FIRMWARE UPGRADE...7
More informationPROFLY / PROBLADE Professional Radio Control PRO-BLADE8
PRO-BLADE8 Ready to Use Remote Control 8 Channel Systems Range: PROFLY Up to 100 metres PROBLADE Up to 500 metres Relay Outputs: Momentary, Latching, Timed Receiver IP65 Applications Lighting Control General
More informationF290X / F293X FOM II Series Fiber Optic Isolator Technical Manual
F290X / F293X FOM II Series Fiber Optic Isolator Technical Manual Revision G Copyright 2017 VERSITRON, Inc. 83 Albe Drive / Suite C Newark, DE 19702 www.versitron.com E031130243 PROPRIETARY DATA All data
More informationXR12. Frequency Change Procedure IS Issue August 2007
XR12 Frequency Change Procedure IS07013 Issue 1.0... 31 August 2007 Nautel Limited 10089 Peggy's Cove Road, Hackett's Cove, NS, Canada B3Z 3J4 T.877 6 nautel (628835) or +1.902.823.2233 F.+1.902.823.3183
More informationP700WLS IoProx Receiver
Installation Manual Warning! This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual
More informationINMOTION Controls Series INSTALLATION & OPERATION MANUAL. INMOTION Series - INMOTION INMOTION-260. Page: 1/15
INSTALLATION & OPERATION MANUAL INMOTION Series - INMOTION-220 - INMOTION-260 Page: 1/15 PREFACE This installation & operation manual is intended as an instruction manual for trained persons who are in
More informationMicroprocessor Control Board Set Up Procedures (OR PLC)
Microprocessor Control Board Set Up Procedures (OR-00 PLC) SWITCHES/PUSHBUTTONS Push Buttons at display SW Enter button SW Back button SW Down SW UP Back light on/off switch Rotary switches on main board
More informationDR-TRC105-EV Evaluation Kit. User s Guide
DR-TRC105-EV Evaluation Kit User s Guide DR-TRC105-304-EV DR-TRC105-315-EV DR-TRC105-345-EV DR-TRC105-372-EV DR-TRC105-390-EV DR-TRC105-403-EV DR-TRC105-434-EV DR-TRC105-450-EV 2010-2015 by Murata Electronics
More informationINSTALLATION & OPERATION MANUAL
INSTALLATION & OPERATION MANUAL PREFACE This installation & operation manual is intended as an instruction manual for trained person who is in charge of installation, maintenance, repair, etc. Before installation
More informationIMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
INSTALLATI INSTRUCTIS Model: RB-G-K10 IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver system is intended to provide
More informationOBJECTIVES EQUIPMENT LIST
1 Reception of Amplitude Modulated Signals AM Demodulation OBJECTIVES The purpose of this experiment is to show how the amplitude-modulated signals are demodulated to obtain the original signal. Also,
More informationManufacturing Access Control since For more information, please visit or call toll free at
Manufacturing Access Control since 1985 www.cdvi.ca 2-Relay Wireless Receiver SEL2641R433-I TERMINaL CONNECTIONS Instruction Manual PR LR RR RV AC/DC C NO C NO NC LV PV 0V 12V 24V - + + 1 2 3 4 5 6 7 8
More information2070-6A Manual A Manual. Dual 1200 baud Modem For The 2070 Controller GDI A MANUAL
2070-6A Manual 1 2070-6A Manual Dual 1200 baud Modem For The 2070 Controller GDI 2070-6A MANUAL This Manual covers Modems with the Serial numbers D700000 and up. 2070-6A Manual 2 GDI 2070-6A Manual This
More information3 GHz Carrier Backhaul Radio. Model: AF-3X. Tel: +44 (0) Fax: +44 (0) LINK GPS MGMT DATA DATA
LINK GPS MGMT DATA DATA MGMT GPS LINK 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA 3 GHz Carrier Backhaul Radio Model: AF-3X LINK GPS MGMT DATA DATA MGMT GPS LINK Introduction Thank you
More informationWEL-200 O P E R A T I N G I N S T R U C T I O N S W I R E L E S S E D G E L I N K
O P E R A T I N G I N S T R U C T I O N S WEL-200 TM W I R E L E S S E D G E L I N K 4564 Johnston Parkway, Cleveland, Ohio 44128 P. 800 426 9912 F. 216 518 9884 Sales Inquiries: salessupport@emxinc.com
More informationWPR400 Wireless Portable Reader User guide
*P516-098* P516-098 WPR400 Wireless Portable Reader User guide Para el idioma español, navegue hacia www.allegion.com/us Pour la portion française, veuillez consulter le site www.allegion.com/us Contents
More informationRevision WI.232FHSS-25-FCC-R and RK-WI.232FHSS-25-FCC-R USER S MANUAL
Revision 1.0.3 WI.232FHSS-25-FCC-R and RK-WI.232FHSS-25-FCC-R USER S MANUAL RADIOTRONIX, INC. WI.232FHSS-25-FCC-R/ RK-WI.232FHSS-25-FCC-R USER S MANUAL Radiotronix 905 Messenger Lane Moore, Oklahoma 73160
More informationAA-35 ZOOM. RigExpert. User s manual. Antenna and cable analyzer
AA-35 ZOOM Antenna and cable analyzer RigExpert User s manual . Table of contents Introduction Operating the AA-35 ZOOM First time use Main menu Multifunctional keys Connecting to your antenna SWR chart
More information2070-6B Manual B Manual. Dual 9600 baud Modem For The 2070 Controller. GDI B Manual. Rev B
2070-6B Manual 1 2070-6B Manual Dual 9600 baud Modem For The 2070 Controller GDI 2070-6B Manual Rev B This Manual covers Modems with the Serial numbers D700000 and up. 2070-6B Manual 2 GDI 2070-6B Manual
More informationPROFESSIONAL WIRELESS MICROPHONE SYSTEM MANUAL
PROFESSIONAL WIRELESS MICROPHONE SYSTEM MANUAL Thank you for selecting this wireless microphone system! The newly system uses the latest PLL SYNTHESIZED and IR TECHNOLOGY, they have excellent and skilled
More informationLBI-31807D. Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1. Maintenance Manual. Printed in U.S.A.
D Mobile Communications MASTR II REPEATER CONTROL PANEL 19B234871P1 Maintenance Manual Printed in U.S.A. This page intentionally left blank 13 PARTS LIST 12 PARTS LIST LBI-31807 11 PARTS LIST 10 SCHEMATIC
More informationPAPILLON 250 ARTICULATED ARM OPENERS 24V DC GEAR MOTOR USER MANUAL
PAPILLON 0 ARTICULATED ARM OPENERS V DC GEAR MOTOR USER MANUAL INDEX. WARNINGS. MOTOR INSTALLATION. DIMENSION CHART. MPONENTS OF INSTALLATION. INSTALLATION OF ARTICULATED ARM OPENER. EMERGEY RELEASE. POWER
More informationSEARCH LITE OPERATION MANUAL
SEARCH LITE OPERATION MANUAL Corporate Profile Trilithic, Inc. was founded in 1986 as an engineering and assembly company providing customized communications and routing systems for business and government
More informationMASTR II BASE STATION MHz RECEIVER IF/AUDIO/SQUELCH & RF ASSEMBLY (25 khz/12.5 khz CHANNEL SPACING) Maintenance Manual LBI-38506A
A Mobile Communications MASTR II BASE STATION 806-824 MHz RECEIVER IF/AUDIO/SQUELCH & RF ASSEMBLY (25 khz/12.5 khz CHANNEL SPACING) TABLE OF CONTENTS RF ASSEMBLY, MIXER AND IF FILTER BOARD...... LBI-30482
More informationParts. Backplate. Battery Cover. Backup Key. Touchscreen Assembly. Inside Assembly. Thumbturn. Strike. Reinforcement Plate. Bolt.
Quick Start Guide Backplate Backup Key Battery Cover Touchscreen Assembly Parts Strike Bolt Inside Assembly Thumbturn Reinforcement Plate Set Screw Reinforcement Screws Inside Assembly Screw Backplate
More informationIMPORTANT: THIS DEVICE MUST BE PROFESSIONALLY INSTALLED. READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION.
INSTALLATI INSTRUCTIS Model: RB-G-K10 IMPORTANT: THIS DEVICE MUST BE PROFESSIALLY INSTALLED. READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI. The Miller Edge RBand Monitored Gate Edge Transmitter/Receiver
More informationPage 1 of 6 Page 1 of 12 Yaesu FT-5100/FT-5200 MODS Rev B (14 Apr 1993) This is a collection of hardware and software mods for the Yaesu 5100/5200 pair. I have the 5100, so I can't verify these for the
More informationInstallation And Programming Instructions For Profile Series With RF Technology
Installation And Programming Instructions For Profile Series With RF Technology A7691A www.sargentlock.com 1 Table of Contents General Description Page 2 3 4 5 6 7 Installation of RF Technology Lock...1
More informationSR3400 Base Station Module Configuration and Use Series-2 Cards Only
SR3400 Base Station Module Configuration and Use Series-2 Cards Only A.W. Communication Systems Ltd Crook Barn, The Crook Rowel Town, Carlisle Cumbria Telephone (44) 1697-748777 Fax (44) 1697-748778 www.toneremote.com
More informationLabMaster Series TECHNOLOGIES. Unistep LabMaster Series PLL LOOP MODULE USER MANUAL. Copyright Unistep Technologies
TECHNOLOGIES LabMaster Series Unistep LabMaster Series PLL PHASE-LOCK LOOP MODULE USER MANUAL Copyright 2010 - Unistep Technologies User Manual PLL Phase-Lock Loop Module 2 PLL ~~~ PHASE--LLOCK LLOOP MODULLE
More informationIMPORTANT: THIS DEVICE MUST BE PROFESSIONALLY INSTALLED READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION
INSTALLATI INSTRUCTIS Models: RB-G-K10, RB-TX10 IMPORTANT: THIS DEVICE MUST BE PROFESSIALLY INSTALLED READ AND UNDERSTAND ALL INSTRUCTIS BEFORE BEGINNING INSTALLATI The Miller Edge RBand Monitored Gate
More informationDear Valued Customer,
Dear Valued Customer, Thank you for choosing Listen! All of us at Listen are dedicated to provide you with the highest quality products available. We take great pride in their outstanding performance because
More information* * APPLICABLE MODELS: 2014 > MAZDA 3
PART NUMBER: 0000 8C L46 GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS Rev. AAA *550-0604-000* APPLICABLE MODELS: 204 > MAZDA 3 REQUIRED COMPONENTS: ITEM QTY DESCRIPTION Usage Chart MIRROR ASSEMBLY: Mirror
More informationDatasheetDirect.com. Visit to get your free datasheets. This datasheet has been downloaded by
DatasheetDirect.com Your dedicated source for free downloadable datasheets. Over one million datasheets Optimized search function Rapid quote option Free unlimited downloads Visit www.datasheetdirect.com
More informationAnti - shoplifting Systems
Anti - shoplifting Systems www.iridiumltd.sk Content About us 3 RF System - Mono 4-10 IRIDIUM Alpha 6 IRIDIUM Kappa 1 7 IRIDIUM Kappa 3 8 IRIDIUM Delta Plexi 9 IRIDIUM Sitius Plexi 10 RF System - Dual
More informationSRX882
Catalog 1. Overview... 2 2. Features... 2 3. Application... 2 4. Electronic Specifications... 3 5. Pin difinition... 3 6. Mechnical dimension... 4 7. Appendix... 4 7.1. Features... 4 7.2. Structure explanation...
More informationAppearance of device and accessories may vary.
Mobile 4G Smart Technology Signal Booster Contents: How it Works.... 1 Before Getting Started.... 2 Quick Installation Overview.... 2 Installing the Outside Antenna.... 2 Installing the Low-Profile Antenna....
More informationRC Camera Control. User Guide v1.3 (RCCC v1.1) 11/7/2012
RC Camera Control User Guide v1.3 (RCCC v1.1) 11/7/2012 kristaps_r@rcgroups INTRODUCTION RC Camera Control board (RCCC) is multifunctional control board designed to for aerial photography or First Person
More informationSound Engineering Solutions
Sound Engineering Solutions bhi NEDSP1061 Noise Reduction Module Yaesu FT-817 Version Fitting Instructions bhi 1061-104D Issue B Page 1 1. Introduction. The bhi NEDSP1061 noise reduction module is a fully
More informationUSER GUIDE FOR FU-05B 0.5W FM TRANSMITTER
USER GUIDE FOR FU-05B 0.5W FM TRANSMITTER CAUTIOIN: NEVER operate the transmitter without connecting a suitable antenna or dummy load to the output otherwise there is a serious danger of destruction of
More informationRF1212 Catalog
Catalog 1. Description... 3 2. Features... 3 3. Application... 3 4. Typical application circuit... 4 5. Electrical Specifications... 4 6. Pin definition... 5 7. Accessories... 5 8. Mechanical dimension...
More informationINSTALLATION AND OPERATING MANUAL
INSTALLATION AND OPERATING MANUAL FOR RBDA-PCS-1/25W-90-A INDOOR REPEATER TABLE OF CONTENTS PARAGRAPH PAGE NO BDA OVERVIEW 3 BDA BLOCK DIAGRAM DESCRIPTION 3 FCC INFORMATION FOR USER 3 BDA BLOCK DIAGRAM
More informationSpecification. What s Included. Power Supply DC, 9V Battery (2) Emitter 10mA Receiver 30mA. Working Current (Max) Signal Output Electrical Status
Specification Product PITS-TP-2 Power Supply DC, 9V Battery (2) Working Current (Max) Signal Transmission Format Signal Output Electrical Status Transmission Distance Dimension Weight Emitter 10mA Receiver
More informationQuick Guide. FCC/IC: MHz CE: MHz
Quick Guide FCC/IC: 340.00-354.00 MHz CE: 433.42-434.42 MHz IMPORTANT: FCC/Canada frequency radios are NOT compatible with CE frequency radios and vice versa. PocketWizard.com/wheretobuy/frequency The
More informationUser Manual. ProRF Encoder Transmitter & Receiver
User Manual ProRF Encoder Transmitter & Receiver WARRANTY Accurate Technology, Inc. warrants the ProScale Systems against defective parts and workmanship for 1 year commencing from the date of original
More informationOVEN INDUSTRIES, INC. Model 5C7-362
OVEN INDUSTRIES, INC. OPERATING MANUAL Model 5C7-362 THERMOELECTRIC MODULE TEMPERATURE CONTROLLER TABLE OF CONTENTS Features... 1 Description... 2 Block Diagram... 3 RS232 Communications Connections...
More informationFrequency Coverage MHz RF Power Output 30W SSB / 9W AM/ 30W FM Dual Finals on Heat Sink Modes AM, FM, USB, LSB Microprocessor
MAGNUM M-257 30W AM/ /FM/SSB 10--11 Meterr Mobile Trranscei ivverr n Prri iiccee: : US$ 250..00 eexx ssttoocckk JJaakkaarrttaa (Arrrri ( iivvi iinngg 2 d weeeekk iinn i Maarrcchh) ) SPECIFICATIONS Frequency
More informationPair of PMR446 Two-Way Personal Radios Model: TP391
Pair of PMR446 Two-Way Personal Radios Model: TP391 USER MANUAL MANUALE D USO MANUEL DE L UTILISATEUR BEDIENUNGSANLEITUNG MANUAL DE USUARIO MANUAL DO USUÁRIO HANDLEIDING BRUKSANVISNING P/N:086L004722-016
More informationCatalog
Catalog 1. Description... - 3-2. Features... - 3-3. Application... - 3-4. Electrical specifications...- 4-5. Schematic... - 4-6. Pin Configuration... - 5-7. Antenna... - 6-8. Mechanical Dimension(Unit:
More informationINSTRUCTION MANUAL MODEL 2779 SUBCARRIER MODULATOR
INSTRUCTION MANUAL MODEL 2779 SUBCARRIER MODULATOR Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc., and may not be reproduced or duplicated in any form without
More informationRigExpert AA-170 Antenna Analyzer (0.1 to 170 MHz) User s manual
RigExpert AA-170 Antenna Analyzer (0.1 to 170 MHz) User s manual Table of contents 1. Description... 3 2. Specifications... 4 3. Precautions... 5 4. Operation... 6 4.1. Preparation for use... 6 4.2. Turning
More informationConnect + compatible
Connect + compatible Looking for a quick setup up guide? There is lots of useful information in this book, but if all you are after is quick set up look for the following headings in this book 1) Setting
More informationInstallation & Quick Start Guide CLB2000 Class B AIS Transponder
Installation & Quick Start Guide CLB2000 Class B AIS Transponder QUICK START CLB2000 - VR1.01 1. Introduction Congratulations on the purchase of your CLB2000 Class B AIS Transponder. It is recommended
More informationALX-SSB 5 Band Filter Assembly Manual 19 November 2018
ALX-SSB 5 Band Filter Assembly Manual 19 November 2018 Contents Theory of Operation:... 1 Figure 1... 2 Parts Included:... 4 Board Overview:... 5 Figure 2... 5 Figure 3... 5 Board Assembly:... 6 Cable
More informationCat. No. H8861 Model: RCL-S-STAT
-AAA Cat. No. H8861 Model: RCL-S-STAT INSTALLATION AND OPERATION INSTRUCTIONS IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS DO NOT ATTEMPT TO INSTALL OR OPERATE INTRODUCTION This remote
More informationSC200 Series. Signal Conditioner MNX10020, REV H 10/17/ Connection Technology Center, Inc Rae Boulevard Victor, NY (585)
SC200 Series Signal Conditioner MNX10020, REV H 10/17/2012 1 CONTENTS SECTION 1: OVERVIEW... 4 Introduction... 4 Description... 4 Ordering Information... 4 Specifications... 5 Environmental... 5 Electrical...
More informationTABLE OF CONTENTS LIST OF FIGURES
7/2/2000 N472 User's Manual TABLE OF CONTENTS TABLE OF CONTENTS... i LIST OF FIGURES... i 1. DESCRIPTION... 1 1.1. FUNCTIONAL DESCRIPTION... 1 2. SPECIFICATIONS...2 2.1. EXTERNAL COMPONENTS... 2 2.2. INTERNAL
More informationproduct overview - EAS antenna -
Warensicherung Beste Qualität zum besten Preis! www.tagging4.com product overview - EAS antenna - ReTec Wandlitz GmbH Thälmannstr. 8 6348 Wandlitz Telefon: +49 (0)33397-80963 Telefax: +49 (0)33397-80965
More informationHeritage MedCall. Sentry E-Call Model HM-527 Resident Host Panel
Heritage MedCall Sentry E-Call Model HM-527 Resident Host Panel 430-527B 0305 Heritage MedCall, Inc. Issue 1, March 2005 Heritage Medcall Sentry Emergency Call System Model 527 Host Panel Installation
More information4000 & 5000 Series. Professional UHF Wireless Systems. Installation and Operation
4000 & 5000 Series Professional UHF Wireless Systems Installation and Operation Receiver Installation Location For best operation the receiver should be at least 3 ft. (1 m) above the ground and at least
More informationR PROFLAME Instruction Book Collection
9.956.028 R00 584 PROFLAME Instruction Book Collection 4-17 18-29 584 PROFLAME System 30-39 Appendix: DIP SWITCH NUMBER (0=ON 1=OFF) 40-41 4-17 Fig. 1 The SIT is a device that allows, in conjunction with
More informationMidland 248XL I NSTRUCTION GUI DE
Midland 248XL I NSTRUCTION GUI DE INDEX Introduction...2 Function and location of the controls...3 Installation...7 Power supply...7 Installing an antenna...7 How to use your Midland 248XL...8 Frequency
More informationModel LIA100. Lock-in Amplifier
Model LIA100 Lock-in Amplifier Operations Manual Thorlabs, Inc 435 Route 206 Newton, NJ 07860 P-(973) 579-7227 F-(973) 300-3600 www.thorlabs.com Doc. Page 1 of 10 Table of Contents Chapter Description
More informationExercise 8. Troubleshooting a Radar Target Tracker EXERCISE OBJECTIVE
Exercise 8 Troubleshooting a Radar Target Tracker EXERCISE OBJECTIVE When you have completed this exercise, you will be able to apply an efficient troubleshooting procedure in order to locate instructor-inserted
More informationLPB OMNI Broadcast Transmitter Installation Procedure Checklist
Installation Procedure LPB OMNI Broadcast Transmitter Installation Procedure Checklist LPB Communications, Inc. 960 Brook Road, Unit 5 Conshohocken, PA 19428 610-825-4100 phone 610-825-4047 fax www.lpbinc.com!
More informationPIM400-TD2. User guide for Panel Interface Module PIM400-TD2
P516-096 PIM400-TD2 User guide for Panel Interface Module PIM400-TD2 Para el idioma español, navegue hacia www.schlage.com/support Pour la portion française, veuillez consulter le site www.schlage.com/support
More informationInterface Manual Tank Level Float Stick System
1 Interface Manual Tank Level Float Stick System SignalFire Model: Sentinel-FS-3BIS The SignalFire Sentinel Float Stick Node is an Intrinsically Safe device with the following features: - Standard SignalFire
More informationPhotoelectrics Amplifier, µ-processor Controlled Type PAM, 2-10 Inputs/2-10 Transistor Outputs
Photoelectrics, µ-processor Controlled Type PAM, 2-10 Inputs/2-10 Transistor Outputs µ-processor controlled unit for up to 10 sets of photoelectric sensors Up to 10 independent outputs Self-diagnostic
More informationWARNING! IMPORTANT NOTICE
WARNING! IMPORTANT NOTICE FCC type acceptance requirments prohibit sales of amplifiers operating below 144 MHz with internal RF sensing circuits that place the amplifier in a transmit mode. Because of
More informationModular Radio Telemetry System
Simple to Use Remote Control 8 Channels per Transmitter 16 Channels per Receiver Upto 48 Transmitters per system Auto Transmit Mode Secure RF Protocol Automatic Watchdog Transmission Range: Upto 200 metres
More informationUSER AND INSTALLATION MANUAL
USER AND INSTALLATION MANUAL Software version 1.0.18 INSTALLATION MANUAL TABLE OF CONTENTS INTRODUCTION 2 WARNINGS 2 TECHNICAL SPECIFICATIONS 2 CONNECTION LAYOUT 3 ELECTRONIC CONNECTIONS 4 RS-485 LINE
More informationNCS-C150 INSTRUCTION MANUAL Rev A. Collcomm Inc. Shipping Address 2310 Pendley Road Cumming, Georgia 30041
NCS-C150 INSTRUCTION MANUAL Rev A Collcomm Inc. d.b.a. NCS Shipping Address 2310 Pendley Road Cumming, Georgia 30041 Mailing Address 1595 Peachtree Parkway Suite 204-123 Cumming, Georgia 30041 Toll Free
More informationUser Manual Information and Product Description. of the. Flap Key Family BOSCH. with Chevy, GMC and GM Logo
User Manual Information and Product Description of the Flap Key Family BOSCH with Chevy, GMC and GM Logo Page 1 of 7 General Description of the RF transmitter: The RF remote control system consists of
More informationSound Engineering Solutions
Sound Engineering Solutions bhi NEDSP1061 Noise Reduction Module Yaesu FT-817 Version Fitting Instructions bhi 1061-104D Issue B Page 1 1. Introduction. The bhi NEDSP1061 noise reduction module is a fully
More informationALACHUA ARES SIMPLEX REPEATER STATION INSTRUCTION MANUAL VERSION 1.0 MARCH
ALACHUA ARES SIMPLEX REPEATER STATION INSTRUCTION MANUAL VERSION 1.0 MARCH 23 2017 1 INTRODUCTION A simplex repeater is nothing more than a digital tape recorder that listens to an FM simplex transceiver,
More informationFFP-C Fiber Fabry-Perot Controller OPERATING INSTRUCTIONS. Version 1.0 MICRON OPTICS, INC.
FFP-C Fiber Fabry-Perot Controller OPERATING INSTRUCTIONS Version 1.0 MICRON OPTICS, INC. 1852 Century Place NE Atlanta, GA 30345 USA Tel (404) 325-0005 Fax (404) 325-4082 www.micronoptics.com Page 2 Table
More informationInstructions for programming and use Starline Roldeck - floorpanel control RD-2001
Instructions for programming and use Starline Roldeck - floorpanel control RD-2001 Microprocessor-based Roldeck control Copyright Starline Technical Support BV. The Netherlands. Alle rechten voorbehouden.
More informationOperating Instructions
LR650 Operating Instructions This product is an accessory or part of a system. Always read and follow the manufacturer s instructions for the equipment you are connecting this product to. Comply with all
More informationLifetime Power Energy Harvesting Development Kit for Wireless Sensors User s Manual - featuring PIC MCU with extreme Low Power (XLP) Technology
P2110-EVAL-01 Lifetime Power User s Manual - featuring PIC MCU with extreme Low Power (XLP) Technology Overview The Lifetime Power is a complete demonstration and development platform for creating battery-free
More informationWIRELESS STEREO WOODEN PANEL SPEAKER SYSTEM
WIRELESS STEREO WOODEN PANEL SPEAKER SYSTEM Owner s Manual Please read before using the equipment INTRODUCTION The 863 MHz stereo wireless speaker system uses latest wireless technology that enables you
More information200, 201 Series Radio Telemetry Transmitters
200 DIN Rail Transmitter Encoder Up to 8 Input Channels Volt Free contact Inputs via Screw Terminals 12 / 24Vdc Supply Range; 433MHz Up to 200 Metres 433MHz NB Up to 1,000 Metres 458MHz Up to 6,000 Metres
More informationLINK GPS MGMT DATA. 4 GHz Licensed Backhaul Radio DATA MGMT GPS. Model: AF-4X LINK
LINK GPS MGMT DATA DATA MGMT GPS LINK 4 GHz Licensed Backhaul Radio Model: AF-4X 4 GHz Licensed Backhaul Radio Model: AF-4X LINK GPS MGMT DATA DATA MGMT GPS LINK Introduction Thank you for purchasing the
More informationFomotech International Corp.
Alpha 600 Series I n d u s t r i a l R a d i o R e m o t e C o n t r o l S y s t e m Operation & Parts Manual Fomotech International Corp. TABLE OF CONTENTS Page 1. SAFETY INSTRUCTION... 2 2. PUSHBUTTON
More information