IPA FITTINGS FOR VEKA DANLINE 70 A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)

Transcription

1 IP FITTINGS FOR VEK DNLINE /S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ 9, DK-9240 NIE TEL: (+4)

2

3 3 FITTINGS FOR VEK DNLINE 70 Table of Contents PGE Profile - VEK Danline 70 4 Suggestion - Number of Hinges Suggestion - Hinge Positions 6 FITTINGS IP No mm Window hinge 7 IP No mm Door hinge 8 IP No Fitting for side swing window 9-10 IP No Reversible Projecting Gears IP No Safety Restrictor IP No. 621 Threated plate for IP No IP No Canopy Stay IP No djustable Canopy Stay 1-16 IP No djustable Canopy Stay - djustable Friction IP No Safety Restrictor IP No Friction Stay for windows 21 IP No Friction Stay for doors 22 IP No Support Fitting 23 IP No Flush olt 23 IP No Casement Hook 24-2 IP No Casement Hook 24-2 IP No Hook Catch 24-2 IP No Casement Fasteners 24-2 Lubrication Instructions 26-27

4 4 FITTING INSTRUCTIONS VEK DNLINE 70 PROFILE

5 SUGGESTION - NUMER OF HINGES The charts below show the number of hinges, we suggest to use on different sizes of windows and doors. The charts shall ONLY be considered as a guidance, as the number of hinges also will depend on the use and weight of the window/door. If the window/door is mounted in a public building with many users (Schools, Railway Stations etc.) then more or even larger hinges are recommended. lso we suggest to use a support fitting whenever possible. WINDOW HINGES: Valid for the window hinges shown in this catalogue. ll window hinges meets the requirements of class 9 (60 Kgs.) in accordance with DS/EN 193. The numbers in brackets are number of hinges in windows with 3-layer glass. Height Width (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (4) (3) 3 (3) 3 (3) 3 (3) (2) 2 (2) 2 (2) 3 (3) (2) 2 (2) 2 (2) 3 (3) (2) 2 (2) 2 (2) 3 (3) (2) 2 (2) 2 (2) (2) 2 (2) 00 2 (2) DOORHINGES: Valid for door hinges shown in this catalogue. ll door hinges with steel pin meets the requirements of class 13 (120 Kgs.) in accordance with DS/EN 193. The same hinges with brass pin meets the requirements of class 11 (80 Kgs.) in accordance with DS/EN 193 Height Width

6 6 FITTING INSTRUCTIONS SUGGESTION - HINGE POSITIONS DOOR WINDOW WINDOW

7 7 WINDOW HINGE IP No ORDERING NO. MTERIL SURFCE C IP NO. STEEL FIXED STEEL PIN STEEL FIXED RSS PIN SQURE EDGES LEFT SQURE EDGES RIGHT GLVNIZED INDUSTRY PCKING IN OXES OF 100 PIECES MM MM C MM MTERIL MM PIN MM SCREW PPROX. WEIGHT KG / PC IP No FITTING INSTRUCTIONS 16 PROFILE - VEK DNLINE 70: FIG. 1 FIG. 2 USE SCREW NO MINTENNCE: TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWICE YER. SEE LSO INSTRUCTIONS ON PGE

8 8 DOOR HINGE IP No C ORDERING NO. MTERIL SURFCE IP NO. STEEL FIXED STEEL PIN STEEL FIXED RSS PIN SQURE EDGES LEFT SQURE EDGES RIGHT GLVNIZED INDUSTRY PCKING IN OXES OF 0 PIECES MM MM C MM MTERIL MM PIN MM SCREW PPROX. WEIGHT KG / PC. IP No FITTING INSTRUCTIONS 16 PROFILE - VEK DNLINE 70: FIG. 1 FIG. 2 USE SCREW NO..0. MINTENNCE: TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - GRESE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER GRESE MINIMUM TWICE YER. SEE LSO INSTRUCTIONS ON PGE

9 SIDE SWING WINDOW 90 0 WITH FRICTION IP No ORDERING NO. MTERIL SURFCE IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRDPCKING IN OXES OF SETS MM MM C MM SCREW PPROX. WEIGHT KG / SET DJUSTLE FRICTION CONVENIENT FOR CLENING SWINGS 90 OPENS CLER FROM CURTINS ND WINDOW FRME MX. VENTILTION CONCELED FITTINGS NODIZED LUMINIUM RILS C TOP FITTING OTTOM FITTING 1 SET RIGHT HND FIRE-ESCPE OPENING: 00 MM FROM SSH WIDTH 726 MM

10 10 IP No FITTING INSTRUCTIONS 16.2 PROFILE - VEK DNLINE 70: FIG. 2 HORIZONTL PLN HINGE SIDE FITTING SHOWN ON FRME CILL RIGHT HND ILLUSTRTION IP NO MX. WEIGHT OF SSH KGS 40 MIN. WIDTH OF SSH MM 31 MX. WIDTH OF SSH MM 820 USE SCREW NO. 4.0 FIG. 3 FITTING: FIG. 1 VERTICL PLN 1. THE FITTING SHOULD E POSITIONED IN THE GROOVES T HED ND CILL OF FRME ND SCREWED ON (FIGURE 1 ND 2) 2. NOW PUSH THE WINDOW SSH INTO POSITION Y SSH SLOTS ND FSTEN THE SCREWS. 3. THE FRICTION CN E DJUSTED ON THE TOP FITTING. IF LRGER OPENING IS WNTED THEN JUST MOVE THE DJUSTLE STOP FITTING IN THE TOP FRME LUMINIUM RIL. MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE

11 REVERSILE PROJECTING GERS IP No.s , IP No & IP No ORDERING NO. IP NO. MTERIL STEEL W/O SPECIFICTIONS SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 1 SET MM MM FRME DIMENSIONS INSIDE MM SCREW PPROX. WEIGHT KG / SET /2 SET IP NO. ORDERING NO. MTERIL STEEL LEFT CONSELED FITTING DJUSTLE FRICTION FULLY REVERSILE OPENS CLER OF CURTINS ND WINDOW FRME NODIZED LUMINIUM RILS SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 20 PCS. MM SCREW PPROX. WEIGHT KG / PC. FIRE-ESCPE OPENING: 00 MM FROM IP NO MM FROM IP NO SFETY RESTRICTOR IP NO ORDERING NO. MTR. SURFCE THRETED PLTE IP NO. 621 IP NO. STEEL W/O SPECIFICTION ELECTROPLTED STNDRD PCKING IN OXES OF 2 PCS ,0 0,12 MM MM SCREW PPROS. WEIGHT KG / PC.

12 12 IP No.s FITTING INSTRUCTIONS PROFILE - VEK DNLINE 70: TOP FRME FIG. 2 TOP SSH FIG. 3 FRME SIDE SSH SIDE IP NO SSH FITTING ON FRME 2. FIG. 1 FITTING: 8, PLCE FITTING INTO OTH SIDES OF THE FRME. 2. POSITION FITTING GINST TOP FRME ND FSTEN. 3. PLCE THE ERING PLTE GINST THE TOP ND GINST THE LUMINIUM RIL ND FSTEN INSERT THE SSH ETWEEN HINGE RMS ND PUSH THE SSH GINST THE STOP RCKET. FSTEN THE SSH STRTING WITH THE SCREW IN THE STOP RCKET.. THE SSH CN E OPENED TO NY NGLE. WITH LRGE OPENING NGLE LIGHT FRICTION CN E OTINED Y MENS OF THE FRICTION SCREWS IN THE SIDES. THE FRICTION HS TO E THE SME ON OTH SIDES. PLESE NOTE THT THE SSH IS NOT SECURED FOR HEVY WINDS ND OTHER HEVY INFLUENCE. IP N0. FITTING LENGTH MM MX. WEIGHT KGS USE THE LRGEST POSSILE FITTING 6. FIT THE RESTRICTOR IP NO ON THE LEFT SIDE, SEE FIG. 1. FOR PROPER FITTING ND OPERTION OF THE RESTRICTOR CORRESPONDING PIECE (170 MM) OF THE WETHER STRIP HS TO E REMOVED. USE SCREW NO OPERTION INSTRUCTIONS: 1. OPEN THE WINDOW - THE RESTRICTOR WILL UTOMTICLLY RESTRICT THE WINDOW. 2. PULL THE SSH 20 MM - PRESS THE RESTRICTOR IN THE DIRECTION OF THE RROW ND OPEN THE WINDOW. 3. WHEN THE WINDOW IS REVERSED FOR CLENING, THE RESTRICTOR WILL LOCK UTOMTICLLY. DISENGGE S MENTIONED IN POINT 2. MINTENNCE: THE FITTINGS RE NOT TO E PINTED. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LIRICTE MINIMUM TWICE YER. DO NOT GRESE THE LUMINIUM RILS. TEST THE OPERTION FROM TIME TO TIME. SEE LSO INSTRUCTIONS ON PGE

13 CNOPY STY WITH FRICTION IP No ORDERING NO. MTERIL SURFCE IP NO. STEEL W/O SPECIFICTION ELECTROPLTED STNDRDPCKING IN OXES OF SETS INDUSTRY PCKING IN OXES OF 2 SETS MM MM SCREW PPROX. WEIGHT KG / SET CONCELED FITTINGS DJUSTLE FRICTION NODIZED LUMINIUM RILS THE MOVEMENT GEOMETRY ENSURES MXIMUM SELING 1/2 SET FIRE-ESCPE OPENING: IP NO MM FROM SSH HEIGHT 826 MM IP NO MM FROM SSH HEIGHT 926 MM 600 MM FROM SSH HEIGHT 1026 MM IP NO MM FROM SSH HEIGHT 1126 MM 600 MM FROM SSH HEIGHT 1326 MM

14 14 IP No FITTING INSTRUCTIONS 16 PROFILE - VEK DNLINE 70: FIG. 1 FIG. 2 IP NO MX. SSH WEIGHT KGS MX. SSH HEIGHT MM SCREW FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE OTTOM HOLE OF THE FITTING. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. ON IP NO MOUNT THE STOPPLTE THROUGH THE UPPER SCREWHOLE IN THE LU RIL UNDER THE SLIDDING ELEMENT. FOR IP NO. 6273: USE THE STOPPLTE TO REDUCE THE OPENING NGLE OF THE SSH TO THE WNTED POSITION. 2. PUSH THE SSH INTO ITS PLCE Y INSERTING IT ETWEEN THE FITTINGS, GUIDED Y THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. THESE STOPS WILL GURNTEE MM G ETWEEN FRME ND SSH. FSTEN THE FITTING STRTING WITH THE SCREW IN THE STOP RCKET (IP NO ). 3. NOW THE FRICTION MY E DJUSTED Y MENS OF THE SCREWS IN THE SLIDES. THE EST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED Y EQUL FRICTION T EITHER SIDE. MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE FIG. 3

15 DJUSTLE CNOPY STY WITH FRICTION IP No ORDERING NO. MTERIL SURFCE IP NO. STEEL W/O SPECIFICTION ELECTROPLTED INDUSTRY PCKING IN OXES OF 2 SETS MM MM SCREW PPROX. WEIGHT KG / SET /2 SET VERTICLLY DJUSTLE ± 1. MM CONCELED FITTINGS DJUSTLE FRICTION NODIZED LUMINIUM RILS THE MOVEMENT GEOMETRY ENSURES MXIMUM SELING FIRE-ESCPE OPENING: IP NO MM FROM SSH HEIGHT 826 MM IP NO MM FROM SSH HEIGHT 926 MM 600 MM FROM SSH HEIGHT 1026 MM

16 16 IP No FITTING INSTRUCTIONS 16 PROFILE - VEK DNLINE 70: FIG. 1 FIG. 2 IP NO MX. SSH WEIGHT KGS 40 0 MX. SSH HEIGHT MM SCREW FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE OTTOM HOLE OF THE FITTING. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. FOR IP NO. 6287: USE THE STOPPLTE TO REDUCE THE OPENING NGLE OF THE SSH TO THE WNTED POSITION. 2. PUSH THE SSH INTO ITS PLCE Y INSERTING IT ETWEEN THE FITTINGS, GUIDED Y THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. THESE STOPS WILL GURNTEE MM G ETWEEN FRME ND SSH. FSTEN THE FITTING STRTING WITH THE SCREW IN THE STOP RCKET 3. NOW THE FRICTION MY E DJUSTED Y MENS OF THE SCREWS IN THE SLIDES. THE EST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED Y EQUL FRICTION T EITHER SIDE. 4. THE SSH CN E DJUSTED ±1. MM UP OR DOWN. EFORE NY DJUSTMENT THE MOUNTING SCREWS IN THE OTTOM IN ECH SIDE OF THE FRME HVE TO E LOOSENED. THEN DJUST Y USING TORX-20 KEY TO TURN THE ECCENTRIC SCREW. Y DELIVERY THE MRK ON THE ECCEN- TRIC SCREW IS IN VERTICL POSITION INDICTING THE 0-POSITION. WHEN THE MRK IS IN HORIZONTL POSITION IN EITHER TOP OR OTTOM, THE FITTING IS DJUSTED TO IT S MX OF ±1. MM. FTER THE DJUSTMENT THE MOUNTING SCREWS IN THE OTTOM OF ECH SIDE RE FSTENED. ECCENTRIC SCREW MRK FIG. 3 MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE

17 DJUSTLE CNOPY STY WITH DJUSTLE FRICTION IP No ORDERING NO. MTERIL SURFCE IP NO. STEEL W/O SPECIFICTION ELECTROPLTED STNDRD PCKING IN OXES OF SETS MM MM SCREW PPROX. WEIGHT KG / SET VERTICLLY DJUSTLE ± 1. MM DJUSTLE FRICTION CONCELED FITTINGS NODIZED LUMINIUM RILS THE MOVEMENT GEOMETRY ENSURES MXIMUM SELING 1/2 SÆT FIRE-ESCPE OPENING: IP NO MM FROM SSH HEIGHT 626 MM 600 MM FROM SSH HEIGHT 726 MM

18 18 IP No FITTING INSTRUCTIONS 16 PROFILE - VEK DNLINE 70: FIG. 1 FIG. 2 IP NO MX. SSH WEIGHT KGS 0 MX. SSH HEIGHT MM 940 SCREW 4.0 FITTING: 1. CLOSE THE FITTING ND PLCE IT IN THE GROOVE OF THE SIDE FRME. PLCE THE FITTING GINST THE TOP FRME. PLCE ND FSTEN THE SCREW IN THE OTTOM HOLE OF THE FITTING. OPEN THE FITTING ND FSTEN THE REMINING SCREWS. 2 PUSH THE SSH INTO ITS PLCE Y INSERTING IT ETWEEN THE FITTINGS, GUIDED Y THE GROOVES IN THE SSH, TILL THE SSH HITS THE STOPS OF THE FITTING. THESE STOPS WILL GURNTEE MM G ETWEEN FRME ND SSH. FSTEN THE FITTING STRTING WITH THE SCREW IN THE STOP RCKET 3. NOW THE FRICTION MY E DJUSTED Y MENS OF THE SCREWS IN THE SLIDES. WHEN DJUSTING LET THE TOP GLIDER MOVE DOWN TO THE STOP. THE EST RESULT FOR THE WINDOW MOVEMENT IS CHIEVED Y EQUL FRICTION T EITHER SIDE. 4. THE SSH CN E DJUSTED ±1. MM UP OR DOWN. EFORE NY DJUSTMENT THE MOUNTING SCREWS IN THE OTTOM IN ECH SIDE OF THE FRME HVE TO E LOOSENED. THEN DJUST Y USING TORX-20 KEY TO TURN THE ECCENTRIC SCREW. Y DELIVERY THE MRK ON THE ECCENTRIC SCREW IS IN VERTICL POSITION INDICTING THE 0- POSITION. WHEN THE MRK IS IN HORIZONTL POSITION IN EITHER TOP OR OTTOM, THE FITTING IS DJUSTED TO IT S MX OF ±1. MM. FTER THE DJUSTMENT THE MOUNTING SCREWS IN THE OTTOM OF ECH SIDE RE FSTENED. MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE ECCENTRIC SCREW MRK FIG. 3

19 19 SFETY CTCH IP No ORDERING NO. MTERIL SURFCE IP NO. STEEL LEFT RIGHT ELECTROPLTED STNDRDPCKING IN OXES OF SETS MM SCREW PPROX. WEIGHT KG / SET 1 SET RIGHT

20 X IP No FITTING INSTRUCTIONS PROFILE - VEK DNLINE 70: MRK 60 SSH X SIDE SSH OTTOM FRME FIG. 1 RIGHT HND ILLUSTRTION FIG THE FITTING CN E USED ON OTH TOPHUNG/TOPGUIDED S WELL S SIDEHUNG/SIDEGUIDED WINDOWS. ON TOPHUNG/TOPGUIDED WINDOWS THE RESTRICTOR IS PLCED IN THE OTTOM OF THE SIDE FRME ND THE RECEIVER IS PLCED IN THE OTTOM OF THE SIDE SSH. ON THE SIDEHUNG/SIDEGUIDED WINDOWS THE RESTRICTOR IS PLCED IN TOP/OTTOM FRME ON THE OPPOSITE SIDE OF THE HINGES ND THE RECEIVER IS PLCED IN THE TOP/OTTOM SSH OPPOSITE THE HINGES. TO CCOMMODTE THE RESTRICTOR IT WILL E NECESSRY TO REMOVE 60 MM OF THE WETHER STRIP S SHOWN ON FIG. 1. X-DIMENSION IS OPTIONL. ON TOPHUNG/TOPGUIDED WINDOWS X MUST MINIMUM E 7 MM. Y USING LRGER X-DIMENSION THE VENTILTION OPENING WILL E EXTENDED. IMPORTNT: THE RECEIVER MUST E MOUNTED SO THT IT HITS THE MRK ON THE RESTRICTOR RM WHEN THE WINDOW IS CLOSED. SEE FIG. 1 OPERTING INSTRUCTIONS: 1. OPEN THE WINDOW UNTIL THE RESTRICTOR ENGGES. 2 PULL THE SSH PPROXIMTELY 20 MM CKWRDS. 3. PRESS THE RESTRICTOR OUTWRDS S YOU OPEN THE WINDOW. 4. WHEN THE WINDOW IS CLOSED THE RESTRICTOR RE-ENGGES UTOMTICLLY. USE SCREW NO. 4.0 MINTENNCE: THE FITTINGS RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN FITTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RILS. SEE LSO INSTRUCTIONS ON PGE

21 21 FRICTION STY for windows IP No ORDERING NO. IP NO. MTERIL STEEL W/O SPECIFICTION SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 2 PCS. MM MM MTERIL MM SCREW PPROX. WEIGHT KG / PC X CONCELED FITTING OPENS UP TILL 100 FRICTION IN LL POSITIONS DJUSTLE FRICTION NODIZED LUMINIUM RIL IP No FITTING INSTRUCTIONS PROFILE - VEK DNLINE 70: FIG FIG. 1 DJUSTLE FRICTION MINTENNCE: THE FITTING RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN MOUNTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RIL. SEE LSO INSTRUCTIONS ON PGE FIG. 3

22 22 FRICTION STY for doors IP No ORDERING NO. IP NO. MTERIL STEEL W/O SPECIFICTIONS SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 10 PCS X MM MM MTERIL MM SCREW PPROX. WEIGHT KG / PCS. CONCELED FITTING OPENS UP TILL 100 FRICTION IN LL POSITIONS DJUSTLE FRICTION NODIZED LUMINIUM RIL IP No FITTING INSTRUCTIONS PROFILE - VEK DNLINE 70: FIG. 1 DJUSTLE FRICTION FIG MINTENNCE: THE FITTING RE NOT TO E PINTED. TEST THE OPERTION FROM TIME TO TIME. WHEN MOUNTING - LURICTE THE PIVOT/MOVLE METL PRTS OF THE MECHNISM WHILE CTIVTING REPETEDLY. HEREFTER LURICTE MINIMUM TWICE YER. DO NOT LURICTE THE LUMINIUM RIL. SEE LSO INSTRUCTIONS ON PGE FIG. 3

23 23 CCESSORIES C SUPPORT FITTING IP NO ORDERING NO. IP N0. MTERIL LUMINIUM W/O SPECIFICTION SURFCE NODIZED STNDRD PCKING IN OXES OF 2 PCS. MM MM C MM SCREW HOLES MM PPROX. WEIGHT KG / PC FLUSH OLT IP NO FLUSH OLT IP NO ORDERING NO. IP NO. MTERIL STEEL SQURE EDGES SURFCE ELECTROPLTED STNDRD PCKING IN OXES OF 10 PCS. MM MM THICKNESS MM OLT MM LENGTH OLT MM SCREW PPROX. WEIGHT KG / PC X X

24 24 CSEMENT HOOKS, HOOK CTCH FITTING & CSEMENT INSTRUCTIONS FSTENERS ORDERING NO. MTERIL SURFCE IP NO. ZINK LLOY WITHOUT SPECIFICTION ELECTROPLTED / WHITE ELECTROPLTED ELECTROPLTED YELLOW STNDRDPCKING IN OXES OF 0 PIECES INDUSTRY PCKING IN OXES OF 20 PIECES MM MM HOLE FOR PIN MM PPROX. WEIGHT KG / 100 PIECES , , IP NO IP NO IP NO IP NO ORDERING NO. IP NO. MTERIL STEEL WITHOUT SPECIFICTION SURFCE ELECTROPLTED / WHITE ELECTROPLTED ELECTROPLTED YELLOW STNDRD PCKING IN OXES OF 0 PIECES INDUSTRY PCKING IN OXES OF 200 PIECES INDUSTRY PCKING IN OXES OF 00 PIECES MM MM EYE SCREW M X (MM) PIN MM SCREW PPROX. WEIGHT KG/100 PCS ,3 34 -,6 3, 0, ,,0

25 2 FITTING INSTRUCTIONS IP NO DRILL MM HOLE FOR RING SCREW SSH 3, FRME FIG. 2 IP NO WITH FIG. 3 IP NO WITH IP NO SSH FRME FRME FIG. 1 IP NO SSH SSH FRME MOUNTING: 1. MOUNT THE RECEIVER IN THE WNTED HEIGHT ON THE SIDEFRME. 2. FOR CSEMENT FSTENERS WITH SCREW PLTE MESURE PRECISELY ON THE SSH ND DRILL MM HOLE FOR THE RING SCREW. MRK UP THE 2 SCREW HOLES ON THE SCREW PLTE ND FSTEN THE CSEMENT FSTENER..

26 26 MINTENNCE FITTING INSTRUCTIONS LURICTION INSTRUCTIONS IP NO IP NO IP NO IP NO IP NR IP NR GENERLLY all parts of a building have to be looked after and maintained from time to time. This of course also applies for fittings in windows and doors. How often fittings in windows and doors should be maintained depends to a large extent on how they are used, how often they are operated, and not least on the environment the fittings are exposed to. Corrosion may also be caused by other factors, such as corrosive liquids, air pollution etc. Special attention should be given to fittings used in windows and doors in urban and industrial areas or other areas with a high traffic intensity as well as coastal areas. Fittings in such environments should be checked and greased more often than fittings used in areas with less corrosive effects. HINGES ND FITTINGS should be lubricated when necessary, or at the minimum twice a year. SLIDING ELEMENTS S WELL S LL LURILS with sliding surfaces are to be kept clean and free from dust and dirt to ensure a smooth sliding function. Stearin wax or a clean lubricating film (but no oil and no grease!) can be applied onto the alluminium rails. ESPGNOLETTES ND OTHER LOCKING FITTINGS should be greased or lubricated with acid free grease or acid free oil on spray. The grease/oil should be applied into the mechanism box as well as on the joints of the side bolts, the roller bolts, or the mushroom head bolts while activating the mechanism repeatedly. Grease or lubricate when necessary or at the minimum twice a year. Continues...

27 27 MINTENNCE LURICTION INSTRUCTIONS RSS will sooner or later get some discoloration in a brownish tone depending on the environment in which it is placed. The original brass surface can be maintained by polishing from time to time. STINLESS STEEL can get some discoloration, although this rarely happens. Different chemical influences like acid fumes, contamination from wood preservation treatments, or air pollution may cause discoloration of the metal, sometimes to a reddish tone which could look like rust. Thin discoloration can be removed just by using common cleaner or polish. PINTED FITTINGS will from time to time need repainting. efore painting all parts should be cleaned carefully. When choosing type of paint and when applying the paint remember to follow the instructions from the paint manufacturer very carefully. When painting a wooden window in a house, it is a good idea also to paint the visible parts of the fittings (please note: No alurails nor sliding parts should ever be painted!). The painting of the fitting will minimize corrosion and add to the lifetime of the fitting. lways make sure that the proper function of a fitting is not affected by the painting. NODIZED LUMINIUM should be cleaned from time to time, depending on the surroundings in which it is placed. Cleaning of the surface with a cloth or sponge is recommended. Eventually a neutral solvent can be used. Emery cloth, steel wool, sodium carbonate, and other cleansers or abrasives containing alkalies or acid should never be used. ON THE WINDOW ND DOOR FCTORY SITE all fittings should be lubricated or greased before shipment. Hinges should be lubricated with acidfree oil while activating repeatedly, an acidfree grease can also be used. When using grease it should be applied directly onto the pin of the hinges. It may be necessary to dismantle the sash before greasing. Especially hinges with a brass pin should be greased. When mounting fittings, please make sure that the tools do not damage the original surface treatment. When original surface has been damaged make sure that remedial take place as soon as possible. WHEN IN DOUT PLESE CONTCT YOUR LOCL SUPPLIER OR /S J. PETERSENS ESLGFRIK.

28 28 FITTING NOTES INSTRUCTIONS

29 NOTES 29

30 30 FITTING NOTES INSTRUCTIONS

31

32 /S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ 9, DK-9240 NIE TEL.: (+4) ipa@ipafittings.com Printed 02/2012