C. Side Panel 1 pc. B. Side Panel. 1 pc. J2. Shelf. 4 pcs. Adjustable Pin 24 pcs. (+1 extra) M3.5x16 Wood Screw 20 pcs. (+1 extra) 2 pcs.

Transcription

1 IMPORTANT Hutch Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly instructions to ensure a completed product as designed. Do not use power tools above 8 volts to assemble. Part List A. Top F. Front Rail G. Back Rail B. Side Panel C. Side Panel D. Middle Panel E. Middle Panel H. Back Upright J1. Fixed Shelf I. Back Panel 3 pcs. K1. Fixed Shelf J2. Shelf 4 pcs. K2. Shelf L. Glass 4 pcs. M. Door N. Door Hardware List Small Hex Wrench Cam Lock Screw 16 pcs. (+1 extra) Magnet 4 pcs. Adjustable Pin 24 pcs. (+1 extra) M4x16 Machine Screw 4 pcs. M6x30 Head Cap Bolt 8 pcs. (+1 extra) Hex Wrench Cam Lock 16 pcs. (+2 extra) M3.5x16 20 pcs. (+1 extra) Door Handle M4x13 for Steel Plate Connector 8 pcs. (+1 extra) Steel Plate Connector Tool(s) required for assembly: Phillips screwdriver, Drill (8 volts or less), 3/8 Drill Bit Home Styles Customer Service: servicedesk@homestyles-furniture.com, ,

2 Assembly Instructions 2/7 IMPORTANT Use a soft cloth between these parts and the floor. Do not use power tools above 8 volts to assemble. Do not tighten all the bolts until each part is properly assembled. The unit must be level to work properly. Use the included adjustable levelers to level. Keep Hex Wrench in a safe place as the bolts may need to be tightened in the future. Cam Lock Screw STEP 1 Insert Cam Lock Screws into pre-drilled holes of Side Panels (B), (C) and Middle Panels (D), (E), then tighten. (See Figure 1) B C D E Cam Lock Screw D Figure 1 Figure 2 E STEP 2 K1 Attach Middle Panels (D) and (E) to Fixed Shelf (K1) with Cam Locks. (See Figure 2) Cam Lock

3 Assembly Instructions 3/7 STEP 3 I H I H I Attach Back Rail (G) to unit with Head Cap Bolts. (See Figure 3) Attach Back Uprights (H) to Back Rail (G). Slide Back Panels (I) into position. G Figure 3 Head Cap Bolt G Head Cap Bolt STEP 4 Attach Back Rail (G) to unit with Head Cap Bolts.

4 Assembly Instructions 4/7 Cam Lock STEP 5 B F Attach Front Rail (F) to unit. Attach Fixed Shelves (J1) to unit with Cam Locks. J1 Attach Side Panels (B) and (C) to unit with Cam Locks. J1 C Cam Lock Magnet STEP 6 Attach Magnets to unit with s into pre-drilled holes. (See Figure 4) Figure 4 for Glass Glass L L STEP 7 M N Remove s for Glass from Doors (M) and (N). L Glass L Slide Glass (L) into Doors (M) and (N), then re-tighten s for Glass.

5 Assembly Instructions 5/7 Head Cap Bolt STEP 8 Insert Adjustable Pins into side panels and middle panels at desired level. A Place Shelves (J2) and (K2) into position. Attach Doors (M) and (N) to unit by sliding door hinges into side panel hinges. (See Figure 5) M J2 K2 J2 Attach Door Handles to Doors (M) and (N) with Machine Screws. (See Figure 6) Attach Top (A) to unit with Head Cap Bolts. J2 Adjustable Pin K2 J2 N Machine Screw Door Handle Figure 5 Figure 6 STEP 9 Insert s into pre-drilled holes of unit.

6 Assembly Instructions 6/7 STEP 10 Attach Hutch to Buffet with Steel Plate Connectors by inserting s for Steel Plate Connectors into pre-drilled holes. (See Figure 7) for Steel Plate Connector Steel Plate Connector Figure 7

7 Assembly Instructions 7/7 IMPORTANT To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly. STEP 11 Place unit at desired location. Drill a 3/8 hole in wall in-line with Pre-drilled hole at top of unit. Anchor in wall 3/8 wall hole Bracket on wall Wall Screw Pre-drilled hole at top of unit Move unit. Insert Anchor into the wall hole and attach Bracket with Wall Screw. Attach Bracket at pre-drilled hole at top of unit with. Tie end Lock end Bracket at top of unit Move unit back into place. Tip-over Restraint Slide Tip-over Restraint through Bracket on wall and Bracket on unit. (See Figure 8) Put tie end of Tip-over Restraint into lock end of Tip-over Restraint and pull until tight. Figure 8 Drill 3/8 hole in wall Top of unit Hardware List Anchor (+1 extra) Bracket (+1 extra) Tip-over Restraint (+1 extra) M3.5x40 Wall Screw (+1 extra) M3.5x16 (+1 extra)

8 CARE INSTRUCTIONS NEVER allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. NEVER use glass cleaners on finished furniture. Ammonia chemically attacks the finish. Do not use power tools above 8 volts to assemble. CRACKING Do not place in direct sunlight. FADING Do not write directly on surface. MARKING Do not place hot objects on surface. FINISH DAMAGE Do not use rubber based placemats. DISCOLORING Do not use commercial waxes and polishes. YELLOWING CLEAN with a soft cloth moistened in lukewarm soap and water. Buff with a dry clean cloth. Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at: Home Styles Customer Service: servicedesk@homestyles-furniture.com, ,