INSTALLATION & OPERATION INSTRUCTIONS LEVER HANDLE LOCKSETS.
|
|
- Margaret White
- 5 years ago
- Views:
Transcription
1 INSTALLATION & OPERATION INSTRUCTIONS FOR LEVER HANDLE LOCKSETS E_EN FOR BRINKS HOME SECURITY INTERIOR LOCKING & NON-LOCKING LEVER HANDLE LOCKSETS. FITS DOORS 1-3/8" (35 mm) TO 1-3/4" (45 mm) THICK WORKS FOR BOTH IN-SWINGING AND OUT-SWINGING DOORS. SEE STEP 2. QUESTIONS? CALL FOR HELP. (S2) MOUNTING SCREWS (2) MOUNTING PLATE (S3) LEVER SCREW & WASHER (Alredy Instlled In Lever) INSIDE LEVER MAIN LOCK BODY PRIVACY BUTTON* INSIDE ROSE OUTSIDE ROSE NOTE: THE MAIN LOCK BODY ALWAYS GOES ON THE OUTSIDE FACE OF THE DOOR. LATCH (S1) WOOD SCREWS (4) STRIKE PLATE PRIVACY KEY* INTERIOR LOCKING LOCKSETS ARE PROVIDED WITH A PRIVACY BUTTON AND PRIVACY KEY. PUSH THE PRIVACY BUTTON TO LOCK THE OUTSIDE LEVER. THE PRIVACY KEY CAN BE USED FOR UNLOCKING BY INSERTING IN THE HOLE IN THE OUTSIDE ROSE AND PUSHING THE PRIVACY BUTTON BACK. OPERATING THE INSIDE LEVER WILL UNLOCK THE OUTSIDE LEVER. (IF THE PRIVACY KEY IS LOST, A PAPER CLIP CAN BE USED ALSO.) FOR NEW INSTALLATIONS, SEE INSTRUCTION E_EN. FOR REPLACEMENT INSTALLATIONS, PROCEED TO STEP 1.
2 FOR NEW INSTALLATIONS, SEE INSTRUCTION E_EN. FOR REPLACEMENT INSTALLATIONS, PROCEED TO STEP 1. STEP 1 IMPORTANT! Adjust For Door Thikness OUTSIDE MOUNTING PLATE SCREW POST Mesure your door thikness. It should e 1-3/8" (35mm) or 1-3/4" (45mm). If in etween these numers, round to the nerest of those two thiknesses. Your lokset is pre-set for 1-3/8" door. If your door thikness is out 1-3/8", proeed to Step 2. If your door is loser to 1-3/4" (45mm) thik, the position of the Outside Mounting Plte must e djusted. Use Phillips Hed Srewdriver to loosen the two Srew Posts tht hold the Mounting Plte. SCREW POST d. e. f. Slide the Mounting Plte k. Lote the Adjustment Ring nd slide it k lso. Rotte the Adjustment Ring until the 45mm nothes on the ring re ligned with the Lugs. Slide the Adjustment Ring ginst the Lugs. ADJUSTMENT RING g. Slide the Outside Mounting Plte k ginst the Adjustment Ring nd seure it y srewing the two Srew Posts k into the Threded Posts on the Mounting Plte. Tighten firmly. d e LUG f g THREADED POST
3 STEP 2 Determine Your Type of Door The Push-Pull-Rotte Lever n e instlled on oth In-Swinging Doors (doors tht re pushed into the room to enter from outside) nd Out-Swinging Doors (doors tht re pulled open to enter room from outside). The Min Lok Body lwys goes on the outside fe of the door. For Out-Swinging Doors, the outside fe is the side of the door on whih the hinges re visile. After instlltion, you will PUSH the lever to enter room with n In-Swinging Door, or PULL the lever to enter room with n Out-Swinging Door. STEP 4 Instll Lth Insert the lth into the 1" (25.4mm) hole in the door edge s shown. Be sure the sloping fe of the lth olt is fing towrds the door jm Insert two (S1) Wood Srews in the feplte holes nd tighten. After instlltion, you should e le to see the Lth Prongs nd Lth Til(s) through the 2-1/8" ore in the door s shown. If not, review Step 3. Selet Approprite Lth. VIEW FROM OUTSIDE THE ROOM IN-SWINGING DOOR OUT-SWINGING DOOR DOOR JAMB MAIN LOCK BODY 2-3/8" - or - 2-3/4" STEP 3 Selet Approprite Lth Bkset is the distne from the door edge to the enter of the 2-1/8" (54mm) hole on the door fe. Selet the 2-3/8" (60mm) or 2-3/4" (70mm) lth sed on the kset of your door. (Most residentil doors hve 2-3/8" kset.) 2-3/8" (60 mm) BACKSET LATCH 2-3/4" (70 mm) BACKSET LATCH PRONGS S1 (2) SLOPING FACE
4 STEP 5 Instll the Min Lok Body Insert the Min Lok Body through the 2-1/8" (54mm) hole in the door. Look through the hole from the inside of the door to guide the Min Lok Body. Mke sure tht the Cylindril Cse engges with the Lth Prongs nd the Retrtor interloks with the Lth Til. d. Test y rotting the lever - the lth olt should retrt. STEP 6 Instll the Inside Mounting Plte nd Rose Ple the Inside Mounting Plte over the Min Lok Body nd ginst the inside door fe with the mounting holes ligned vertilly. Position the mounting plte so it reds FACE OUT when it is ginst the door. Insert the two (S2) Mounting Srews nd engge the threded holes in the Min Lok Body. Tighten firmly. For Interior Loking models, srew the Privy Button onto the threded shft. Tighten firmly y hnd. d. Instll the Inside Rose y ligning with the nothes on the Mounting Plte nd snpping it on. (For Interior Loking models, ensure tht the hole in the Rose ligns with the Privy Button.) STEP 7 Instll Inside Lever Push the Inside Lever onto the Spindle until it stops. Tighten the (S3) srew loted on the inside of the lever. The srew will engge the hole in the Spindle. Test instlltion y pushing, pulling nd rotting the lever. SPINDLE FACE OUT PRONGS MAIN LOCK BODY RETRACTOR LATCH BOLT CYLINDRICAL CASE INSIDE MOUNTING PLATE (S2), FACE OUT INSIDE ROSE d PRIVACY BUTTON (S3) INSIDE LEVER
5 STEP 8 Instll Strike Plte Seure the Strike Plte with two (S1) Wood Srews. Tighten firmly. It is importnt for Push-Pull-Rotte Loks for the Lth Bolt to move freely in nd out of the Strike Plte. STRIKE PLATE LATCH BOLT (S1) STEP 9 Opertion & Trouleshooting PUSH-PULL Lever Opertion Alwys PUSH or PULL the lever ner the end s shown for est results. In-Swinging Doors To open the door from the outside, PUSH the outside lever or rotte the lever in either diretion. To exit the room, PULL the inside or rotte the lever in either diretion. Out-Swinging Doors d. To open the door from the outside, PULL the outside lever or rotte the lever in either diretion. e. To exit the room, PUSH the inside lever or rotte the lever in either diretion. Interior Loking Lever Loksets f. PUSH the Privy Button to lok. PULL the Privy Button out or operte the inside lever to unlok. PUSH DO NOT PUSH HERE PULL Trouleshooting g. The PUSH nd PULL funtions work est when the lth olt n move freely in nd out of the Strike Plte. h. Wether stripping or wrped door n sometimes fore the olt ginst the Strike Plte. This will inrese the fore neessry to PUSH or PULL the lever. For est results, re-position the Strike Plte so there is no fore ginst the olt. f UNLOCK LOCK FULL LIFETIME WARRANTY - This produt is fully wrrnted to e free of defets in mteril nd workmnship for the life of the produt. If defet in mteril or workmnship ours, ll for instrutions on how to hve it repled or repired free of hrge. This wrrnty is null nd void if the produt ws used for purposes for whih it ws not designed, is used, misused, modified or improperly instlled, operted, mintined, nd/or repired. NOT LIABLE FOR INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES. Some sttes do not llow the exlusion or limittion of inidentl or onsequentil dmges, so the ove limittion or exlusion my not pply to you. This wrrnty gives you speifi rights, nd you my lso hve other rights tht vry from stte to stte. Brink s trdemrk & opyright works re used with permission E_EN Hmpton Produts Interntionl Corp. 50 Ion, Foothill Rnh, CA USA Hmpton Produts Interntionl Corp E_EN_REVA 02/15
* * 98/9949WDC. 1-Point Latch (LBL) 2-Point Latch includes these additional parts. Customer Service
*24017501* 24017501 Coneled Vertil Devie for Wood Doors 98/9949WDC Instlltion Instrutions 1-Point Lth (LBL) 2-Point Lth inludes these dditionl prts NOTE: If door does not hve utout for ling inside lok
More informationMODEL 351 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH "H" HOLDER ARMS
MODEL POWERGLIDE SERIES INSTRUTIONS FOR INSTLLING SRGENT LOSERS WITH "H" HOLDER S SERIES NON SIZED DJUSTLE SIZES THRU 6 UTION: FILURE TO INSTLL OR DJUST PROPERLY MY RESULT IN INJURY OR DMGE. FOR SSISTNE,
More informationMulti-Point Astragal Prehanger Installation Instructions
Multi-Point Astrgl Prehnger Instlltion Instructions 8817 West Mrket Street Colfx, NC 27235 800.334.2006 www.endurproducts.com Tools Required: Endur Router Templte (or equivlent) Router with 5/8" dimeter
More informationUltimate Flip Lever Astragal Prehanger Installation Instructions
Ultimte Flip Lever Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Tpe Mesure Kit Includes: Full Astrgl Full Length Trim Strip Screw Pck Field Pck
More informationEntry Mortise Lock Set Lever to Lever
Entry Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Turn Piece 4 Mortise Lock 5 Scalp 6 Mortise Lock Strike 7 Mortise Lock Dust Box 8 Mortise Cylinder 9 Cylinder Swing Cover 10 Spindle 11 Spindle
More informationPassage Mortise Lock Set Lever to Lever
Passage Mortise Lock Set Lever to Lever 1 Lever 2 Escutcheon 3 Mortise Lock 4 Scalp 5 Mortise Lock Strike 6 Mortise Lock Dust Box 7 Spindle 8 Spindle Spring 9 Spindle Retainer 2 1 9 8 7 9 7 8 3 1 2 4 5
More informationUltimate Trilennium Astragal Prehanger Installation Instructions
Ultimte Trilennium Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Power Drill with 1" Drill Bit Tpe Mesure 1" Spde Bit Kit Includes: Full Astrgl Full
More informationFor installation help please visit Please Do Not Return Product to Store!
Instlltion Guide Replement Sreen Housing for ndersen Luminire Retrtle Inset Sreen Door For instlltion help plese visit www.ndersenluminire.om/instll Plese Do Not Return Produt to Store PLESE ll the Storm
More information1" MORTISE INSTALLATION INSTRUCTIONS
K Aess Control 2941 Indin Avenue Winston-Slem, NC 27105 USA Tel: (800) 849-8324 (336) 725-1331 Fx: (800) 346-9640 (336) 725-3269 www.kess.om www.e-plexlok.om PKG3140 0507 1" MORTISE INSTALLATION INSTRUCTIONS
More informationSERVICE MANUAL 9940/20/10
9940/0/0 9/0/00 Tle of ontents REMOVING THE EXTERIOR PARTS... A. Light Cover... B. Bse... C. Top Cover (Flp)... 4 D. Hinge Cover... 4 E. Thred Tension Cover... 4 F. Side Enlosure... 5 G. Hndle nd Unit
More informationCM5100 COMPUTER MANAGED CYLINDRICAL LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL
The 5100 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5100 employs a heavy-duty mechanical design which is easy to install and highly reliable. The FSE
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationLEITNER DESIGNS FULL SIZE / MIDSIZE LEITNERDESIGNS.COM V1 Page 1
LEITNER DESIGNS C T I V E C R G O S Y S T E M FULL SIZE / MIDSIZE LEITNERDESIGNS.COM SLES@LEITNERDESIGNS.COM 949-395-3049 V1 Page 1 SSEMBLY / INSTLLTION INSTRUCTIONS: CTIVE CRGO SYSTEM PRT NUMBERS: 00-6266-F-01-1135
More informationUltimate Push Button Astragal Prehanger Installation Instructions
Ultimte Push Button Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Power Drill with 1" Drill Bit Tpe Mesure Kit Includes: Full Astrgl Full Length
More informationFOR DEVICES SOLD PRIOR TO
23970734 98/9949 CS 98/9949 FOR DEVICES SOLD PRIOR TO 8-10-16 This instruction covers new instlltion of the 98/9949 conceled verticl device for hollow metl nd luminum doors. RF Instlltion Instructions
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationNORTH STAR 4-PANEL PATIO DOOR ASSEMBLY INSTRUCTIONS
40684 Talbot Line, St. Thomas, Ont., N5P 3T Phone: (519) 637-7899 Toll Free: (800) 65-5701 Fax: (519) 637-3403 Web Site: www.northstarwindows.com NORTH STR 4-PNEL PTIO DOOR SSEMLY INSTRUCTIONS (JN/P-Dr04/4Panssy
More informationSSRLS-3 / SSRLU-3 Installation Instructions
5mm Hex Nut Upper Telescoping hannel & Screws Packing List QTY. ITM 1 Top Telescoping hannel 1 ottom Telescoping hannel w/ self drilling screw 15" 18" 1 Top and ottom Rod with connecting arm 25-½ 2 ¼ -
More informationEE1000 SERIES INSTALLATION INSTRUCTIONS
Kaba ccess ontrol 2941 Indiana venue Winston-Salem, N 27105 US Tel: (800) 849-8324 (336) 725-1331 Fax: (800) 346-9640 (336) 725-3269 www.kabaaccess.com PKG2282 0307 EE1000 SERIES INSTLLTION INSTRUTIONS
More informationPacking List MODEL TEL-IAL-481 For Inactive Leaf TRIDENT double door
Items: SECURITECH GROUP, INC. MP uxiliary POLICE LOCK Packing List MODEL TEL-IL-481 For Inactive Leaf TRIDENT double door Items with * are pre-installed or assembled Fasteners: Part# Qty Name Description/Usage
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationHardware Installation. Do this first:
1 Do this first: Hardware Installation Need some help? Here s what you ll need: 4 AA Batteries Phillips screwdriver Visit us online. support.remotelock.com We re here to help. 1 (877) 254 5625 support@remotelock.com
More information8800 Series Mortise Lockset Knob, Lever, Reflections and Security Trims Installation Instructions
8800 Series Mortise Lockset Knob, Lever, Reflections and Security Trims Installation Instructions IMPORTNT: The accuracy of the door preparation is critical for the proper functioning and security of this
More informationInstallation Instructions Model # TEL-100 / 200 Manual Locking or Self Locking
INSTLLTION INSTRUTIONS TL-100 / 200 GSS-oors TL 1-406-212-2334 MIL rg@gssdoors.com W www.gssdoors.com GSS oors (406) 212-2334 (406) 897-2121 rg@gssdoors.com www.gssdoors.com TM Multi-Point eadbolt Installation
More informationInstallation Instructions ENGLISH
Installation Instructions ENGLISH Interior Latchset PRIVACY (Bed & Bath) PASSAGE (Hall & Closet) PK.5400 Congratulations! With your purchase of this Interior Latchset, you re among a group of discerning
More informationSafety glasses Measuring tape Level Pencil Power drill Center punch Phillips screw driver Saw horse
EX76 Concealed Vertical Rod Exit Device Preparation Guide and Installation Instructions Box Contents EX76 Concealed Vertical Rod Exit Device Back Bar Active Push Bar Filler Plate Door Kit with Templates
More informationNORTH STAR 2-PANEL PATIO DOOR ASSEMBLY INSTRUCTIONS
40684 Talbot Line, St. Thomas, Ont., N5P 3T2 Phone: (59) 637-7899 Toll Free: (800) 265-570 Fax: (59) 637-3403 Web Site: www.northstarwindows.com NORTH STR 2-PNEL PTIO DOOR SSEMBLY INSTRUCTIONS I:\PDssembly\2Panel\CovPg.doc
More informationTravel Trailer Latch With Dead Bolt Trailer Latch With Dead Bolt. U.S. Patent No. 5,927,773
60-250 Travel Trailer Latch With Dead Bolt 60-251 Trailer Latch With Dead Bolt Service Manual (Installation and Troubleshooting) U.S. Patent No. 5,927,773 CONTENTS 1. BASIC COMPONENTS 2. INSTALLATION OF
More informationInstallation instructions for the Apex and Volt Electric Locksets
Please refer to G+ Lockset Installation Manual for Instructions on how to use this template Paper size A3. These dimensions are for reference only to ensure that scale is correct. Power transfer unit heights
More informationWALL UNIT. Assembly Guide Tall 1 Door. 200 Tall. 350 Tall. 150 Tall. 300 Tall. 400 Tall. 450 Tall. 500 Tall. 600 Tall
WLL UNIT ssembly uide 150 Tall 200 Tall 300 Tall 350 Tall 400 Tall 450 Tall 500 Tall 600 Tall or Internal Use: I.WR.INS.045_WKIN00130_WLL_150_600_Tall_1Dr_Rev3.indd WLL UNIT ssembly uide EORE YOU STRT
More information660 Freestyle/Style Door with Double In-Line Panels
660 Freestyle/Style Door with Doule In-Line Pnels (CUH or MG) Style Series Option M Metl HK87 Slide MGNTIC PULL HNDL KIT with Mgnet Vinyl 989 MGNTIC DOOR STOP 716 HDR / SILL INSRT O V678 VINYL DOOR SL
More informationCM5500 COMPUTER MANAGED MORTISE LOCK INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More information120x165mm. 85x165mm TEMPLATE. ELECTRONIC DEADBOLT model no.: & & Toll-free Number:
20x65mm 85x65mm ELECTRONIC EABOLT FOR BACSET 2 3/4" ( 70 mm) FOR BACSET 2 3/8" ( 60 mm) Ø 2 /8" ( 54 mm ) Toll-free Number: -800-268-659 IMPORTANT: Please read this manual carefully before installing this
More information4600 INSTALLATION INSTRUCTION W/ 2190
1 STILE PREPARATION DOOR VERTIAL L STRIKE PREPARATION ALUMINUM FRAME.218 1.594 5/32" OFFSET (SEE STEP-8) 1 1/4" RIVNUT INSTALLATION FOR SINGLE OR DUAL LEVERS ON ALUMINUM STILE 5/32" OFFSET (SEE STEP-9)
More informationShepherd 210A Fingerprint Door Lock Installation Manual V1.1
Shepherd 210A Fingerprint Door Lock Installation Manual V1.1 Hongda USA Inc. 2505 Technology Dr. #2-6A, Hayward, CA 94545, USA Phone: (510) 887-5682 Fax: (510) 372-0487 Email: info@hongdausa.com Website:
More informationD2/367A ASSEMBLY INSTRUCTIONS 6 BAY AV CREDENZA. Salamander 6 Bay AV Credenza [5.17] page 1 of 8
D2/367 SSEMBLY INSTRUCTIONS 6 BY V CREDENZ Salamander 6 Bay V Credenza 503-232 [5.17] page 1 of 8 hardware B I L C J D K M E ID PRT # DESCRIPTION F G H 303-453 1/4-20 x 4 Head Socket Screw B 300-518 1/4-20
More information* * 33/3549A CS 33/3549A. 2-Point Latch includes these additional parts. 1-Point Latch (LBL) Customer Service. Installation Instructions
*23970726* 23970726 33/3549A CS 33/3549A Instlltion Instructions This instruction covers new instlltion of the 33/3549A conceled verticl device for luminum nd hollow metl doors. RF Also covered is the
More informationCRCODE-202. Mechanical Lock. Instruction and Programming Manual. Before Installing:
CRCODE-202 Mechanical Lock Instruction and Programming Manual Before Installing: 1. Please read the instructions carefully to prevent missing important steps. *Note: Improper installations may result in
More informationRim-Lock Door Set Installation Instructions
Rim-Lock Door Set Installation Instructions Let s get started Check Your Parts List Two Doorknobs with Set Screws B. Doorknob Spindle C. Rim Lock with Mounting Screws D. Keeper with Mounting Screws E.
More information3000 ELECTRONIC STRINGING MACHINE OWNER S MANUAL
3000 ELETRONI STRINGING MHINE OWNER S MNUL OMPONENTS...2 SSEMLY INSTRUTIONS...3 MOUNTING THE FRME...4 STRING LMP OPERTION...4 ELETRONI TENSION HED...5 MINTENNE TIPS...6 WRRNTY...7 OMPONENTS The Prince
More informationPOWER TRIM. Table of Contents. Section 5C - Dual Power Trim System
SERVICE MANUAL NUMBER 28 Tle of Contents POWER TRIM Setion 5C - Dul Power Trim System DUAL POWER TRIM SYSTEM Lurints / Selnts / Adhesives..... 5C-2 Importnt Informtion................ 5C-2 Testing Dul
More informationWALL UNIT. Assembly Guide For Internal Use: FI.WR.INS.034_WKIN00124_WALL_ _1Dr_Rev4.indd
WLL UNIT ssembly uide 150 200 350 400 500 300 450 600 or Internal Use: I.WR.INS.034_WKIN00124_WLL_150-600_1Dr_Rev4.indd WLL UNIT ssembly uide EORE YOU STRT INSTLLTION SHOULD E PERORMED Y OMPETENT PERSON
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationInstallation Instructions
for s TOC Table of Contents 1 Mortise Lock Handing Instructions.... 2 2 3 4 5 Mortise Lock Door Preparation & Installation... 3 HSS Trim Installation.... 5 Knob x Knob...6 Lever x Knob....7 Turn-Piece
More informationInstallation Instructions
999-00451 Smart Deadbolt Secure control from anywhere. Installation Instructions Simply Smart Security. Installation Instructions 999-00451 Box Contents Screw Cover Key (2) Exterior Assembly Gasket Drive-in
More informationMORTISE LOCK INSTALLATION INSTRUCTIONS
MORTISE LOCK INSTALLATION INSTRUCTIONS INSPIRE TM ROSELESS DESIGNER TRIM FM 340 Rev. 10/18 TABLE OF CONTENTS: DOOR PREPARATION 1 ML2000 LOCK HANDING 2 FULL WORKING TRIM (STD) 3 HALF WORKING TRIM (M30)
More information6 BAY AV CREDENZA WITH DUAL DISPLAY MOUNT
D2/367M2 SSEMLY INSTRUCTIONS 6 Y V CREDENZ WITH DUL DISPLY MOUNT TIP HZRD WRNING! For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions may result in instability causing
More informationCM5500 COMPUTER MANAGED MORTISE LOCK HARD-WIRED (FSE/FSA) INSTALLATION MANUAL
The 5500 series lock is a stand-alone, microprocessor controlled, electromechanical locking system. The 5500 employs a heavy-duty mechanical design with fewer moving parts that a standard mechanical mortise
More informationWD WD7000 Series
WD-7000 12-WD7000 Series Wood Door Concealed Vertical Rod Multi-Point Lock Installation Instructions Copyright 2015, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction
More informationDHAR Test Assessment No. DHAR a.1 Page 1 of 3. The Fire Resistance Performance of E+ Doorsets with nominated variation to the Door lockset
Exova Warringtonfire Aus Pty Ltd Unit 2, 409-411 Hammond Road Dandenong, Victoria 3175 T: +61 (0)2 8270 7600 F: +61 (0)2 9299 6076 W: www.exova.com Postal Address: PO Box 4282 Dandenong South, Victoria
More informationInstallation Instructions for Trilock Omni BB Twin Pull Handle Version - Suits 35mm to 45mm door thickness
Installation Instructions for Trilock Omni BB Twin Pull Handle Version - Suits 35mm to 45mm door thickness Step 1. Fold template where indicated. Position template on door edge at desired lock / latch
More informationTP Series - Triple PV Top of Pole Solar LED Lighting System
TP Series - Triple PV Top of Pole Solr LED Lighting System Instlltion Mnul MKTG-TP34-02-EN-1113 Instlltion Mnul TP Series Importnt Notes nd Wrnings This instlltion nd instruction mnul provides instlltion
More informationAL Series. Tropical Lighting System. Installation Manual
AL Series Tropicl Lighting System Instlltion Mnul Importnt Notes nd Wrnings This instlltion nd instruction mnul provides instlltion instructions for the Sol Tropicl Lighting System (AL) Series solr LED
More informationCONCEALED ROD CRASH BAR PR-7085 SERIES EXIT DEVICE ASSEMBLY DETAILS PR mm. 10mm. Lock cylinder. 10mm. Cross bar length (see note #8) Dogging
Floor line TITLE ASSEMLY DETAILS PR-7085 4:02 Hinge stile (inside) Lock stile (inside) Lock stile (outside) Drill 5mm (.20) and tap 1/4-20 (2) Drill 7mm (.266) holes (2) 9mm 12mm See note #6 160mm 9.5mm
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More informationExponents Bench Cushion
Exponents Bench Cushion Power Drill #2 Phillips Bit Bit Holder Page 1 of 2 939500640 Rev A 1. Place cushion on top of the bench, so the black Coalesse tag is in the right rear corner of the bench. 2. From
More information"WALDEN"PETITE FIREPLACE FA PLANTATION OAK FA9102 CLASSIC MAHOGANY FA ANTIQUE WHITE FA BLACK. Assembly Instructions
"WLDEN"PETITE FIREPLE F9101 - PLNTTION OK F9102 LSSI MHOGNY F9103 - NTIQUE WHITE F9104 - LK ssembly Instructions For assistance with assembly contact: Southern Enterprises Inc. ustomer Service 1-800-633-5096
More informationInstallation Instructions
by Precision Screen & Security s 27040 San Bernardino Ave, Redlands, CA 92374 www.precision-screens.com TM Installation Instructions NOTE: Prior to Permanently mounting the BacTrac, insure the handle and
More informationSLIDING DOOR LOCKS MISCELLANEOUS
MISCELLANEOUS SLIDING DOOR We offer the BEST delivered prices on this NEW pocket door hardware of any dealer, big discounts off the MSRP prices listed here. Give us a call toll free at (888) 3062298 or
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTLLTION GUIDE FOR SHOWER ENLOSURE ()! SFETY PREUTIONS This Installation Guide uses the following symbols to indicate important information. lways observe the instructions indicated by
More informationAXIS DOORS - INSTALLATION MANUAL CORNER (2W)
XIS DOORS - INSTLLTION MNUL ORNER (2W) THIS MNUL PPPLIES TO LL 48 ND 60 ORNER XIS SERIES SHOWER DOORS XIS48-2W, XIS60-2W, ND XIS60T-2W visit www.acryline.ca RYLINE 2015 rue écancour Lyster, Quebec, anada
More information* * 9875/ Customer Service #10-24 # Dogging Key (use to lock down pushbar)
*911374-00* 911374-00 Mortise Exit Device 9875/9975 Installation Instructions #10-24 #12-24 Dogging Key (use to lock down pushar) Customer Service 1-877-671-7011 www.allegion.com/us Allegion 2015 Printed
More information98/9927. Devices covered by these instructions: Surface Vertical Rod Exit Device
911375-00 Surface Vertical Rod Exit Device 98/9927 Installation Instructions Devices covered by these instructions: 98/9927 Surface Vertical Rod Exit Device 98/9927-F (Fire) Surface Vertical Rod Exit Device
More informationAssembly and Operation Guide
MK-C MK-G MK-W Mount Kits ssembly and Operation Guide Thank you for your purchase of Treasure Garden s MK Mount Kit.. Please remove all contents from the package, inspect and review checklist. MK MOUNT
More informationInstallers guide Deadbolt 02.
Installers guide Deadbolt 02. version 0.7.1 Specifications Model igloohome Smart Deadbolt 02 Material Zinc Alloy Current Rating (Standby) ~30uA Current Rating (Active) ~200mA Batteries 4 x AA Alkaline
More informationInstallation Type. Edge of Door. Pull (Hinge) Side Mounted. Hinge Edge of Door. Push (Stop) Side Mounted
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationOperation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine Product Code: 888-V12/V13/V15
GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Produt Code: 888-V12/V13/V15 Be sure to red this doument efore using the mhine. We reommend tht you keep this
More informationEntry Mortise Handleset
1. Pencil 2. No. 2 and No. 3 Phillips Head Screwdrivers 3. No. 1 and No. 2 Slotted Screw Drivers 4. 1/8" Allen Head Wrench 5. 3/4" Wood Chisel or Corner Chisel 6. Measuring Device 7. Lock Mortising Tool
More informationGETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Operation Manual. Computerized Sewing Machine
GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Importnt Sfety Instrutions Plese red these sfety instrutions efore ttempting to use the mhine. This mhine is
More informationCanopy Bed Frame. Date: 8 Jun 15 www. potterybarn.com Page 1 of 12 Rev:
Cnopy Bed Frme Dte: 8 un 15 www. potterybrn.com Pge 1 of 12 Importnt Sfety Instructions: WARNIN: Do not llow children to climb on, pull on, or hng from cnopy. Filure to follow these instructions cn result
More informationRETRACTABLE SCREEN ASSEMBLY AND INSTALLATION INSTRUCTIONS. SINGLE OUTSWING (Retro) / (Full-Size) STEP 1: REVIEW & CHECK FIG.
STEP 1: REVIEW & CHECK ) CONFIRM DOOR HEIGHT & WIDTH You have purchased a SINGLE Retractable Screen for an INSWING door. HEIGHT: This unit is available in two sizes: Retro and Full-Size. Please make sure
More informationTools Required. * When installing on a fire door, please see instructions below. *
CL615 Tubular Mortice Latch with Code Free option CL615 Tubular Mortice Latch with Code Free option Number relating to picture Item 1 Front Plate and handle * 2 Back Plate and handle * 3 Neoprene seals
More informationDCM Series DC T-Series Non-Spring Return Rotary Electronic Damper Actuators
DCM-0 Series DC-0-T-Series Non-Spring Return Rotry Eletroni Dmper Atutors. Atutor. U-olt shft pter. Position initor EA0R e f g. Shft pter loking lip e. Position initor pter f. Mounting rket g. Mounting
More informationInstallation Instructions For The 8850FL Series Mortise eboss
Installation Instructions For The 8850FL Series Mortise eboss Electronic Battery Operated Security Solution FEATURES Battery Operated (Hardwire Capable) Motorized Grade 1 Mortise Lock 94 User Code Capacity
More information3 BAY AV CREDENZA WITH SINGLE DISPLAY MOUNT
D2/337M1 SSEMLY INSTRUCTIONS 3 Y V CREDENZ WITH SINGLE DISPLY MOUNT TIP HZRD WRNING! For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions may result in instability causing
More informationInstallation Instructions
Installation Instructions CAUTION An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility
More informationWNA Series. Knobsets AVAILABLE STYLES AVAILABLE FINISHES. Finish A 26 26D 34 3W BEVERLY HUNTINGTON PHOENIX TROY BHMA Code
WNA Series Knobsets AVAILABLE STYLES Beverly Huntington Phoenix Troy AVAILABLE FINISHES Are in Brilliance finish in certain funtions Finish 3 5 15 17A 26 26D 34 3W BEVERLY HUNTINGTON PHOENIX TROY BHMA
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTLLTION GUIDE FOR SHOWER ENLOSURE ()! SFETY PREUTIONS This Installation Guide uses the following symbols to indicate important information. lways observe the instructions indicated by
More informationASY P.O. BOX 729 TERRELL, TEXAS / PAGE 1 OF 13 SAM
203 Madix Inc., ll rights reserved ommon Parts 2 MXI GRI WIRE GRI SHELF WITH (GPWGS) MXI GRI FIXTURE PNEL (GPWFP) FIXTURE PNELS RE USE S EN SUPPORT. SHELF N E USE NYWHERE. MXI GRI REINFORMENT R 3 (GPR)
More informationVista SCREEN. and Double Door Link Kit. Installation Manual for. For Double Doors (French Doors) Quick and Easy to Size and Install
and Double Door Link Kit Installation Manual for Vista SCREEN TM Quick and Easy to Size and Install For Double Doors (French Doors) Durable. Reliable. Attractive. For door openings up to 72 13 /16 (1,849
More informationD3976 RECESSED EXIT INSTALLATION INSTRUCTIONS
PACKAGE CONTENTS PRODUCT MUST BE INSTALLED ACCORDING TO ALL APPLICABLE BUILDING AND LIFE SAFETY CODES TEMPLATE INSTALLATION INSTRUCTIONS STRIKE HAND TOOL 5/32 HEX KEY ROD END CAPS EXIT DEVICE CRANK ARM
More informationASSA ABLOY. Installation Instructions. MP9800 Series Multi-Point Lock. MP9800 Series Multi-Point Lock Wood Doors. Wood Doors ASSA ABLOY.
Installation Instructions MP9800 Series Multi-Point Lock MP9800 Series Multi-Point Lock, the global leader in door opening solutions 1 of 12 Copyright 2016 Corbin Russwin Inc., an Group company. Table
More informationPlease Do Not Return Product to Store!
Instlltion Guide for ndersen Luminire Retrctble Insect Screen Door with Slidewy Insect Screen System Designed for 6 wide by 80 tll single hinged doors with suitble mounting surfce. For instlltion help
More informationEXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM
RECORD & LABELS WHAT THIS OWNER'S CAN DO FOR YOU It explains exactly how The Rite Door operates. It explains periodic maintenance requirements necessary to assure reliable operation. It explains simple
More information1/8" Balsa 8B 7B 6B. For Radio Control. Wingspan - 25" CAD Drawing by Paul Bradley Sheet 1 of 12 INCHES. Cowl pattern.
R1 1/8" alsa R2 owl pattern 1/16" Square enter Windshield Pattern 1/16" Square filler forward of stab 9T 8T 7T R3 10 R4 T1 T2 9 Side Windows Pattern Fuselage sides are built using 1/16" square stock 8
More informationInstallation Instructions for 45H & 47H Mortise Locks
Installation Instructions for 45H & 47H Mortise Locks Contents These installation instructions describe how to install your 45H & 47H Mortise Lock. Topics covered include: Finishing the preparation...
More informationBiesemeyer fi T-Square fi Commercial Fence Systems 50 Capacity (Model ) 30 Capacity (Model ) INSTRUCTION MANUAL
iesemeyer fi T-Square fi Commercial Fence Systems 50 Capacity (Model 78-904) 30 Capacity (Model 78-907) INSTRUCTION MNUL D T E D 3-5-96 P RT NO. 1349984 'Delta International Machinery Corp. 1996 INTRODUCTION
More informationASSA ABLOY Series Installation Instructions. Regular Arm. Parallel Arm. Top Jamb Mount. Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models
9500 Series Installation Instructions Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models Regular Pages 5 & 6 Parallel Pages 7 & 8 Top Jamb Mount Pages 9 & 10 IMPORTANT: An improperly installed or
More informationAssembly Instructions for Java Furniture: JFV65 & JFV75
Assemly Instrutions for Java Furniture: JFV65 & JFV75 Thank you for Choosing the Java Furniture Line from Sanus Systems. If you have any questions regarding this or any other Sanus Systems produt, please
More informationInstallation Instructions
VON DUPRIN Installation Instructions 98/9947WDC Concealed Vertical Rod Exit Device Wood Door Applications Devices covered by these instructions: 98/9947WDC Concealed Vertical Rod Device 98/9947WDC-F (Fire)
More informationSecurity Products & Services...That Never Sleep. Sur-Lock. I/O 2000L Family of Exit Control Alarm Locks. Installation Instructions
Security Products & Services...That Never Sleep Sur-Lock I/O 2000L Family of Exit Control Alarm Locks Installation Instructions IMPORTANT It is important that you read and follow these instructions carefully.
More informationOperation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine
GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Importnt Sfety Instrutions Plese red these sfety instrutions efore ttempting to use the mhine. This mhine is
More informationINSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY
INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY A B C L M N D E F G O P Q H I J Tools provided in Amesbury installation kit: (A) door router fixture, (B) doorframe router fixture, (C) ½
More informationED1100 /1100F SERIES RIM EXIT DEVICE INSTALLATION INSTRUCTIONS
E1100 /1100F SERIES RIM EIT EVIE INSTALLATION INSTRUTIONS Ver.2 1100 SERIES RIM EIT EVIE End ap End ap Bracket End ap End ap Bracket over Plate Mechanism ase enter ase SPEIAL TOOLS REQUIRE Push Bar Hex
More informationInstallation Instructions. Installation Type
Installation Instructions 800 & 8050 Slide Track Door Closers Non Hold Open & Hold Open Models Note: Hold open models are not permitted to be installed in Listed fire door assemblies. PULL SIDE MOUNTED
More information4000 Series. The Gainsborough 4000 Series Heavy Duty Cylindrical Locksets KEY IN KNOB LOCKSETS
The Gainsborough 4000 Series Heavy Duty Cylindrical Locksets are designed and manufactured for use in commercial buildings, including hotels and offices, but are also ideal for residential entrances and
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More information33/3547A. Special tools needed: #10-24 tap Drill bits: #25, 5/16, 13/32, 1/2
911404-00 Concealed Vertical Rod Exit Device 33/3547A Installation Instructions Devices covered by these instructions: 33/3547A and 33/3548A Concealed Vertical Rod Exit Device 33/3547A-F and 33/3548A-F
More informationHOT GLASS WILL CAUSE BURNS DO NOT TOUCH GLASS UNTIL COOLED NEVER ALLOW CHILDREN TO TOUCH GLASS
Glass Guard ssembly instructions for Glass Guard-, Glass Guard-0, Glass Guard-, Glass Guard-, Glass Guard--R, Glass Guard-0-R, Glass Guard-0-R, Glass Guard--L, Glass Guard-WV and Glass Guard-66 Keep children
More information4 BAY Low Profile - SINGLE XL DISPLAY WALL MOUNT CABINET
D1/347Mxl SSEMLY INSTRUCTIONS 4 Y Low Profile - SINGLE XL DISPLY WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use with video monitors weighing 300 lbs (136kg) or less. Use with
More information