MODEL 351 POWERGLIDE SERIES INSTRUCTIONS FOR INSTALLING SARGENT DOOR CLOSERS WITH "H" HOLDER ARMS
|
|
- Maurice Clark
- 6 years ago
- Views:
Transcription
1 MODEL POWERGLIDE SERIES INSTRUTIONS FOR INSTLLING SRGENT LOSERS WITH "H" HOLDER S SERIES NON SIZED DJUSTLE SIZES THRU 6 UTION: FILURE TO INSTLL OR DJUST PROPERLY MY RESULT IN INJURY OR DMGE. FOR SSISTNE, LL SRGENT T STNDRD PPLITION (TYPE -H ) LOSER MOUNTED ON HINGE SIDE OF NOTE: FOR H8 MOUNTING SEE DT SHEETS ENLOSED STNDRD & TOP JM PPLITIONS USE PGE WIDTH (INHES) OVER 8 NUMER OF TURNS OF SPRING POWER DJUSTING SREW FROM FTORY SETTING (USE HRT S GUIDE ONLY) PPROXIMTE INTERIOR S WEIGHT (POUNDS) EXTERIOR S 80 FTORY SET 0 - W 0 - W -7 W W FTORY SET W - W UP TO 8 W S REQ. W ND UP S REQ. DJUST SPRING POWER ORDING TO HRT* TOP JM PPLITION (TYPE -H, -HZ, -HZ) INRESE POWER + - DERESE POWER LOKWISE (W) OUNTER LOKWISE (W) USE PGE LEFT HND PULL HINGE SIDE PULL HINGE SIDE /8" SPRING POWER DJUSTMENT NUT RIGHT HND LOSER MOUNTED ON FRME ON STOP SIDE OF STOP (PUSH) SIDE STOP (PUSH) SIDE PRLLEL PPLITION ONLY PRLLEL PPLITION (TYPE -PH9) LOSER MOUNTED ON STOP SIDE OF USE PGE WIDTH (INHES) OVER 8 NUMER OF TURNS OF SPRING POWER DJUSTING NUT FROM FTORY SETTING (USE HRT S GUIDE ONLY) INTERIOR S PPROXIMTE WEIGHT (POUNDS) EXTERIOR S W W - W 0 8- W FTORY SET W -7 W UP TO 8 W S REQ. 8 W ND UP S REQ. DJUST SPRING POWER ORDING TO HRT* *IF INTERIOR S DO NOT HVE TO OMPLY WITH D REQUIREMENTS, EXTERIOR SETTINGS RE REOMMENDED. WHERE STRONG DRFTS EXIST, INRESE SPRING POWER S NEEDED Y TURNING SPRING DJUSTMENT SREW LOKWISE. IF NEESSRY, REDUE SPRING POWER Y TURNING SREW OUNTERLOKWISE. opyright 007, 008, Sargent Manufacturing ompany, an SS LOY Group company. 7
2 STNDRD PPLITION INSTRUTIONS IMPORTNT: USE LTERNTE MOUNTING IF N OPEN EYOND LIMITS SHOWN FOR STNDRD MOUNTING TYPE MOUNTING MX. OPENING H HOLDER STNDRD 0 9 /" LTERNTE 60 6 /" /" 9 /" "" "" TOP OF /" /8" IF UTT, FRME ND WLL ONDITIONS PERMIT WILL OPEN 80 RIGHT HND SHOWN. LEFT HND OPPOSITE. 9/6" /" THIS DIMENSION IS TKEN FROM HINGE EDGE OF FOR INVISILE HINGES. DRILL & TP ND USE SREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. SEE PGE 6 FOR MORTISE NUTS. INSTLL LOSER TO WITH SPRING DJUSTMENT NUT WY FROM HINGE. 9" L OF HINGE PIVOT: UTTS, OFFSET PIVOTS, SWING LER, ENTER HUNG OR INVISILE HINGES # x WOOD SREWS OR #- X / FLT HED MHINE SREWS NOTE: LOSER ODIES RE NON HNDED. IT IS IMPORTNT THT THE LOSER ODY E MRKED WITH RH SYMOL T TOP, FOR RIGHT HND S. LH SYMOL T TOP FOR LEFT HND S. RH RIGHT HND SHOWN TTH FOOT TO FRME S SHOWN WITH NUT UP FOR RH OR DOWN FOR LH. TTH WITH INDEX MRK LIGNED S SHOWN. SEURE WITH SREW ND WSHER. INSERT ROD END INTO SWIVEL ND TIGHTEN SREW S SHOWN ELOW. NUT FES UP RIGHT HND MIN RIGHT HND HOLD OPEN LEFT HND POSITION OF MIN WHEN SSEMLING SREW 90 ROD INDEX MRK NUT FES DOWN opyright 007, 008, Sargent Manufacturing ompany, an SS LOY Group company. 7
3 TOP JM PPLITION INSTRUTIONS TYPE REVEL DEPTH OPENING RIGHT HND SHOWN, LEFT HND OPPOSITE. H HZ HZ 0" TO " 0 /8" TO " 0 /8" TO 8" 0 THIS DIMENSION IS TKEN FROM HINGE EDGE OF FOR INVISILE HINGES. OPENING TO 80 IS POSSILE IF DEPTH OF REVEL IS NOT GRETER THN " DRILL & TP ND USE SREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. SEE PGE 6 FOR MORTISE NUTS. /8" 9" /" 6" 7/6" 8 7/8" OF PIVOT HINGE L MOUNTING PLTE /" - - MOUNTING PLTE REQUIRED FOR DOULE RETED. INSTLL LOSER TO FRME/MOUNTING PLTE WITH SPRING DJUSTMENT NUT WY FROM HINGE. " FRME TOP OF " # X /" WOOD SREWS OR #- X /8" FLT HED MHINE SREW SINGLE RETED FRME /8" L OF PLTE MOUNTING SREWS NOTE: LOSER ODIES RE NON HNDED. IT IS IMPORTNT THT THE LOSER ODY E MRKED WITH RH SYMOL T TOP, FOR LEFT HND S. LH SYMOL T TOP FOR RIGHT HND S. /6" /8" DEPTH OF REVEL /8" /6" DEPTH OF REVEL /" MIN. " 7/6" /" DOULE RETED FRME WITH REQUIRED - MOUNTING PLTE " TTH FOOT TO WITH NUT UP FOR LH, DOWN FOR RH NUT FES UP LH RIGHT HND SHOWN RIGHT HND RIGHT HND NUT FES DOWN INSTLL MIN ND SEURE WITH SREW ND WSHER S SHOWN. INSERT ROD END INTO MIN ND TIGHTEN SREW. S RE HNDED ND MUST E THE SME HND S. LEFT HND RIGHT HND POSITION OF MIN WHEN SSEMLING HOLD OPEN SREW ROD 90 MIN VIEW LOOKING UP WHEN SSEMLING INDEX MRK HOLD OPEN 90 SREW ROD opyright 007, 008, Sargent Manufacturing ompany, an SS LOY Group company. POSITION OF MIN WHEN SSEMLING 7
4 PRLLEL PPLITION INSTRUTIONS MX. OPENING 0 9 7/8" 0 /" OF L HINGE PIVOT (UTT HINGE SHOWN) /6" /" /" # WOOD SREWS OR #- x /8 FLT HED MHINE SREWS 80 7" 7 /8" LEFT HND SHOWN. RIGHT HND OPPOSITE. /" 7/8" TOP VIEW DO NOT USE THIS MOUNTING FOR SWING LER HINGES. THIS DIMENSION IS TKEN FROM HINGE EDGE OF FOR INVISILE HINGES. DRILL & TP ND USE SREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED. SEE PGE 6 FOR MORTISE NUTS. INSTLL LOSER TO WITH SPRING DJUSTMENT NUT WY FROM HINGE. /8" /" OF L HINGE PIVOT 9" STOP TOP OF # x WOOD SREWS OR #- X /" MHINE SREW TTH FOOT RKET TO FRME STOP ND MOUNT HOLD OPEN TO RKET WITH DJUSTING NUT FING DOWN FOR LEFT HND, FING UP FOR RIGHT HND. RIGHT HND SHOWN RH NOTE: LOSER ODIES RE NON HNDED. IT IS IMPORTNT THT THE LOSER ODY E MRKED WITH RH SYMOL T TOP, FOR RIGHT HND S. LH SYMOL T TOP FOR LEFT HND S. LEFT HND SHOWN NUT FES DOWN USING WRENH ON OTTOM END OF SPINDLE, ROTTE SPINDLE ND SSEMLE MIN TO LOSER S SHOWN, ND THEN INSERT ROD END INTO SWIVEL ND TIGHTEN SREW POSITIONING /" WY FROM. LEFT HND VIEW OF INDEX RIGHT HND VIEW OF INDEX INDEX MRK PRELOD PPROX. INDEX MRK MIN NUT FES UP OPTIONL FOOT RKET FLUSH TRNSOMS. SEE DT SHEET ENLOSED. PH RKET RIGHT HND SHOWN MIN UTION: LOSER WILL NOT OPERTE PROPERLY IF IS NOT INDEXED ORRETLY. /" SWIVEL HOLD OPEN RIGHT HND MIN SREW POSITION OF MIN WHEN SSEMLING LEFT HND OPPOSITE FOOT RKET opyright 007, 008, Sargent Manufacturing ompany, an SS LOY Group company. 7
5 FINL DJUSTMENT ND REGULTING PROEDURE KHEK VLVE OPTIONL DELYED TION VLVE DELYED TION RNGE SPEED VLVE LTHING SPEED VLVE LTHING SPEED RNGE LOSING SPEED RNGE KHEK RNGE REGULTING SPEED ND LTHING SPEED S NEEDED. USE HEX SOKET (/8" LLEN) WRENH ND TURN VLVES LOKWISE TO SLOW DOWN OR OUNTER LOKWISE TO SPEED UP MOVEMENT. FSTER (+) SLOWER ( ) REGULTING KHEK TO REGULTE THE INTENSITY OF KHEK TION TURN VLVE LOKWISE TO INRESE OR OUNTER LOKWISE TO DERESE HEKING. UTION: SET VLVE FOR SLIGHT USHIONING EFFET. IT IS DMGING TO THE LOSER IF THE HEKING TION IS TOO RUPT. NEVER USE KHEK S STOP. LWYS USE STOP TO STOP THE. FOR MODELS WITH OPTIONL DELYED TION FETURE DELYED TION PROVIDES SLOW LOSING THROUGH DELYED TION RNGE TURN VLVE LOKWISE TO SLOW DOWN OR OUNTER LOKWISE TO SPEED UP MOVEMENT D DJUSTMENT OF HOLD OPEN. SLIGHT TIGHTENING OR LOOSENING OF HOLD OPEN NUT HNGES HOLDING POSITION OF. NOTE: TO PROTET WLL, TRIM ND LOSER, USE STOP LOTED 0 EYOND HOLD OPEN POSITIONS UT NOT EYOND THE MX. OPENING SHOWN ON INSTRUTIONS. USE /6" WRENH TO DJUST NUT HOLD OPEN NUT E INSTLL OVER WITH TWO SREWS S SHOWN. INSERT IS REMOVLE. PLE IN UNUSED OPENING. opyright 007, 008, Sargent Manufacturing ompany, an SS LOY Group company. 7
6 USING MORTISE NUTS WITH SRGENT LOSER. SEE INSTRUTIONS OR DT SHEET PKED WITH LOSER FOR DIMENSIONS LOTING THE LOSER ODY ND FOOT ON ND FRME.. MORTISE NUT SHOWN IS DESIGNED FOR N UNREINFORED METL.. FOR TOP JM ND ORNER RKET PPLITIONS: THE LOSER FOOT WILL E TTHED TO THE IN MNNER SIMILR TO THT SHOWN FOR MOUNTING THE LOSER ODY.. FOR S /" THIK: MORTISE NUT SHOWN FOR /" THIK S WILL E FURNISHED LONG WITH PPORPRITE LENGTH THRU-OLTS. ONSTRUTION MUST PROVIDE RIDGE TYPE REINFOREMENT TO PREVENT THE RIL FROM OLLPSING WHEN THRU-OLTS RE TIGHTENED. SRGENT 0 SERIES LOSER SHOWN. (OTHER SERIES SIMILR) FRME SEE NOTE # ELOW FOR DIMENSION INFORMTION. IF DIMENSION LESS THN 7/8" IS USED. THE STOP MUST E UT TO LER THE MORTISE NUT HED OR THE MORTISE NUT HED MUST E REESSED. (SEE ENLRGED VIEW "Y") STOP OVER MORTISE NUT HED DRILL /8" DI. HOLE FOR MORTISE NUT ODY. DRILL /" DI. HOLE FOR MOUNTING SREWS SHORTEN MORTISE NUT ODY TO THIS LENGTH FRME /8" /8" DI. HOLE STOP LOSER SHOWN (TRK SSEMLY MOUNTING IS SIMILR) /" DI. DRILLED HOLE /8" DI. HOLE MORTISE NUT HED #- THRED 9/6" DI. MORTISE NUT 7/6" /6" FOR /" THIK /6" FOR /8" THIK (SEE NOTE # FOR /" THIK S) opyright 007, 008, Sargent Manufacturing ompany, an SS LOY Group company. 7 6
* * 98/9949WDC. 1-Point Latch (LBL) 2-Point Latch includes these additional parts. Customer Service
*24017501* 24017501 Coneled Vertil Devie for Wood Doors 98/9949WDC Instlltion Instrutions 1-Point Lth (LBL) 2-Point Lth inludes these dditionl prts NOTE: If door does not hve utout for ling inside lok
More informationSERVICE MANUAL 9940/20/10
9940/0/0 9/0/00 Tle of ontents REMOVING THE EXTERIOR PARTS... A. Light Cover... B. Bse... C. Top Cover (Flp)... 4 D. Hinge Cover... 4 E. Thred Tension Cover... 4 F. Side Enlosure... 5 G. Hndle nd Unit
More informationINSTALLATION & OPERATION INSTRUCTIONS LEVER HANDLE LOCKSETS.
INSTALLATION & OPERATION INSTRUCTIONS FOR LEVER HANDLE LOCKSETS 999-00333E_EN FOR BRINKS HOME SECURITY INTERIOR LOCKING & NON-LOCKING LEVER HANDLE LOCKSETS. FITS DOORS 1-3/8" (35 mm) TO 1-3/4" (45 mm)
More informationFor installation help please visit Please Do Not Return Product to Store!
Instlltion Guide Replement Sreen Housing for ndersen Luminire Retrtle Inset Sreen Door For instlltion help plese visit www.ndersenluminire.om/instll Plese Do Not Return Produt to Store PLESE ll the Storm
More information351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS
2 351 DOOR CLOSER WITH DOUBLE LEVER ARM (OP) INSTALLATION INSTRUCTIONS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary door
More informationFOR DEVICES SOLD PRIOR TO
23970734 98/9949 CS 98/9949 FOR DEVICES SOLD PRIOR TO 8-10-16 This instruction covers new instlltion of the 98/9949 conceled verticl device for hollow metl nd luminum doors. RF Instlltion Instructions
More information* * 33/3549A CS 33/3549A. 2-Point Latch includes these additional parts. 1-Point Latch (LBL) Customer Service. Installation Instructions
*23970726* 23970726 33/3549A CS 33/3549A Instlltion Instructions This instruction covers new instlltion of the 33/3549A conceled verticl device for luminum nd hollow metl doors. RF Also covered is the
More informationINSTRUCTIONS FOR 1431 Door Closer with Hold Open Arms 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
INSTRUCTIONS FOR Door Closer with Hold Open Arms SERIES ADJUSTABLE FROM SIZE THRU 6 FOR INSTALLATION ASSISTANCE CALL SARGENT AT -800-77-77 / www.sargentlock.com Installation Instructions based on Application
More information660 Freestyle/Style Door with Double In-Line Panels
660 Freestyle/Style Door with Doule In-Line Pnels (CUH or MG) Style Series Option M Metl HK87 Slide MGNTIC PULL HNDL KIT with Mgnet Vinyl 989 MGNTIC DOOR STOP 716 HDR / SILL INSRT O V678 VINYL DOOR SL
More information1" MORTISE INSTALLATION INSTRUCTIONS
K Aess Control 2941 Indin Avenue Winston-Slem, NC 27105 USA Tel: (800) 849-8324 (336) 725-1331 Fx: (800) 346-9640 (336) 725-3269 www.kess.om www.e-plexlok.om PKG3140 0507 1" MORTISE INSTALLATION INSTRUCTIONS
More informationA '-4" 10'-10" 16'-6" 7'-0" 23'-0" 10 3/4" 9'-6" 5 1/4" 2'-11 1/2" 2'-6" 3'-2 3/4" 3'-1" 4'-8 3/4" 2'-5 3/4" 2'-6" 7'-2" R.O. HD 7'-3" R.O.
Name of Trust, First Floor Plan -. -. 7'-" 0'-0" '-" 7'-0" '-0" -. N '-0" 9'-0" 7'-" 7'-" '-0" '-" " 0" '- /" '-0" '- /" 9" '-0" 9" '-0" 0 /" '-" '- /" '-" '-" '-0" '-" 0 /" 9'-" /" '- /" '-" '- /" '-"
More information4 BAY Low Profile-Dual Displays WALL MOUNT CABINET
D1/347M2 SSEMLY INSTRUTIONS 4 Y Low Profile-Dual Displays WLL MOUNT INET TIP HZRD WRNING! abinet must be affixed to wall. For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions
More informationPOWER TRIM. Table of Contents. Section 5C - Dual Power Trim System
SERVICE MANUAL NUMBER 28 Tle of Contents POWER TRIM Setion 5C - Dul Power Trim System DUAL POWER TRIM SYSTEM Lurints / Selnts / Adhesives..... 5C-2 Importnt Informtion................ 5C-2 Testing Dul
More informationASY P.O. BOX 729 TERRELL, TEXAS / PAGE 1 OF 13 SAM
203 Madix Inc., ll rights reserved ommon Parts 2 MXI GRI WIRE GRI SHELF WITH (GPWGS) MXI GRI FIXTURE PNEL (GPWFP) FIXTURE PNELS RE USE S EN SUPPORT. SHELF N E USE NYWHERE. MXI GRI REINFORMENT R 3 (GPR)
More informationInstallation Instructions. Hold Open Arm Models. Sized (Sizes 2,3,4,5) Weaker BC-H 9303BC-H 9304BC-H 9305BC-H
O Regular rm ee Page Instructions Hold Open rm Models tronger ized (izes,,4,5) 90H 90H 904H 905H 900H eries Non Handed loser O Regular rm Top Jamb Parallel rm Regular rm ee Page eft Hand H Right Hand Reverse
More informationDCM Series DC T-Series Non-Spring Return Rotary Electronic Damper Actuators
DCM-0 Series DC-0-T-Series Non-Spring Return Rotry Eletroni Dmper Atutors. Atutor. U-olt shft pter. Position initor EA0R e f g. Shft pter loking lip e. Position initor pter f. Mounting rket g. Mounting
More information* * 98/9949 CS 98/ Point Latch includes these additional parts. 1-Point Latch (LBL) Customer Service. Installation Instructions
*23970734* 23970734 98/9949 CS 98/9949 Instlltion Instructions This instruction covers new instlltion of the 98/9949 conceled verticl device for hollow metl nd luminum doors. RF Also covered is the CS
More informationCanopy Bed Frame. Date: 8 Jun 15 www. potterybarn.com Page 1 of 12 Rev:
Cnopy Bed Frme Dte: 8 un 15 www. potterybrn.com Pge 1 of 12 Importnt Sfety Instructions: WARNIN: Do not llow children to climb on, pull on, or hng from cnopy. Filure to follow these instructions cn result
More informationPORCH. Canopies and Accessories DECKING SYSTEMS. For more information. STOCKISTS For details of your nearest stockist for any product:
DECKING SYSTEMS For more informtion STOCKISTS For etils of your nerest stokist for ny prout: 0 01 TECHNICAL HELPLINE For further help n vie: 0 1 INTERNET rihrurige.o.uk EMAIL info@rihrurige.o.uk Whittington
More information"WALDEN"PETITE FIREPLACE FA PLANTATION OAK FA9102 CLASSIC MAHOGANY FA ANTIQUE WHITE FA BLACK. Assembly Instructions
"WLDEN"PETITE FIREPLE F9101 - PLNTTION OK F9102 LSSI MHOGNY F9103 - NTIQUE WHITE F9104 - LK ssembly Instructions For assistance with assembly contact: Southern Enterprises Inc. ustomer Service 1-800-633-5096
More informationSARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUH (HOLD OPEN) ARMS
SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUH (HOLD OPEN) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE. FOR ASSISTANCE,
More informationNORTH STAR 4-PANEL PATIO DOOR ASSEMBLY INSTRUCTIONS
40684 Talbot Line, St. Thomas, Ont., N5P 3T Phone: (519) 637-7899 Toll Free: (800) 65-5701 Fax: (519) 637-3403 Web Site: www.northstarwindows.com NORTH STR 4-PNEL PTIO DOOR SSEMLY INSTRUCTIONS (JN/P-Dr04/4Panssy
More informationINSTALLATION GUIDE SPACE SAVER PARTITION CURRENT F DOOR. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIDE SPE SVER PRTITION 0 - URRENT F-0 - DOOR STRONG RELILE SEURE pro-gard.com.0.0 THESE OMPONENTS RE REQUIRED TO INSTLL THE PRTITION PRTS LIST REV SHEET UTHOR DTE QTY PRT NUMER X /-0 x / RRIGE
More informationPORCH. Canopies and Accessories. For more information. STOCKISTS For details of your nearest stockist for any product:
For more informtion STOCKISTS For etils of your nerest stokist for ny prout: 0 01 TECHNICAL HELPLINE For further help n vie: 0 1 INTERNET www.rihrurige.o.uk EMAIL info@rihrurige.o.uk Whittington Ro Oswestry,
More informationSARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS
SARGENT 1331 DOOR CLOSER INSTALLATION INSTRUCTIONS WITH JUO (JO & JP9) ARMS Strength Adjustable From Size 1 Thru 6 CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE Auxiliary
More informationFitting & User Instructions
Issue 03 Alexnder Universl Furniture Risers Note: These frmes require the ddition of n ttchment. (See pges 4 - ) Bse Frme Mrk Bse Frme Mrk Fitting & User Instructions These instructions pply to the rising
More informationMulti-Point Astragal Prehanger Installation Instructions
Multi-Point Astrgl Prehnger Instlltion Instructions 8817 West Mrket Street Colfx, NC 27235 800.334.2006 www.endurproducts.com Tools Required: Endur Router Templte (or equivlent) Router with 5/8" dimeter
More informationOperation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine Product Code: 888-V12/V13/V15
GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Produt Code: 888-V12/V13/V15 Be sure to red this doument efore using the mhine. We reommend tht you keep this
More informationGETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Operation Manual. Computerized Sewing Machine
GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Importnt Sfety Instrutions Plese red these sfety instrutions efore ttempting to use the mhine. This mhine is
More informationInstallation Instructions Model # TEL-100 / 200 Manual Locking or Self Locking
INSTLLTION INSTRUTIONS TL-100 / 200 GSS-oors TL 1-406-212-2334 MIL rg@gssdoors.com W www.gssdoors.com GSS oors (406) 212-2334 (406) 897-2121 rg@gssdoors.com www.gssdoors.com TM Multi-Point eadbolt Installation
More informationUPTOWN CANOPY FRAME T/F/Q
UPTOWN CANOPY FRAM T/F/Q Dte: 30 Mr 16 www.pbteen.com Pge 1 of 12 mportnt Sfety nstructions: Plese red ll instructions crefully before ssembling. For your sfety, ssembly by two or more dults is strongly
More information4 BAY Low Profile - SINGLE XL DISPLAY WALL MOUNT CABINET
D1/347Mxl SSEMLY INSTRUCTIONS 4 Y Low Profile - SINGLE XL DISPLY WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use with video monitors weighing 300 lbs (136kg) or less. Use with
More informationSSRLS-3 / SSRLU-3 Installation Instructions
5mm Hex Nut Upper Telescoping hannel & Screws Packing List QTY. ITM 1 Top Telescoping hannel 1 ottom Telescoping hannel w/ self drilling screw 15" 18" 1 Top and ottom Rod with connecting arm 25-½ 2 ¼ -
More informationInstallation Instructions
Installation Instructions s asy s I 200 Series Multi-Sized thru 6 Universal oor losers Tri-Pack Standard as 20 Regular rm Parallel rm Jamb Mount 200 IMPORTNT: OR INSTLLIN: Pages 2 & 20 Pages & 5 220 Pages
More informationNOTE THAT THE HANDLE IS BELOW THE LOCK BASE
NOTE THT THE POSITION OF STOP IS LOCTED USING THE SINGLE HOLE S PLCEMENT GUIDE. NOTE THT THE HNDLE IS ELOW THE LOCK SE DETIL G SCLE.5. OF CHNGE DTE SIGN RELESED FOR PRODUCTION // RQ G SEE SHEET 3 FOR P/N
More informationOperation Manual Sewing Machine
Opertion Mnul Sewing Mhine Produt Code: 888-S33/S36 KNOWING YOUR SEWING MACHINE SEWING BASICS UTILITY STITCHES APPENDIX Be sure to red this doument efore using the mhine. We reommend tht you keep this
More information4 BAY Low Profile WALL MOUNT CABINET
D1/347 SSEMLY INSTRUCTIONS 4 Y Low Profile WLL MOUNT CINET TIP HZRD WRNING! Cabinet must be affixed to wall. For use to prevent tipping in compliance with capacity of cabinet specified. Use with heavier
More informationCANOPY SYSTEMS PAGE 1 OF 14
NOPY SYSTEMS PGE 1 OF 1 SY 092 I N S T L L T I O N I N S T R U T I O N S RED REFULLY! minimum of of two persons are required to install canopies. Do not step on base shelves... to avoid damage:. Do not
More information1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6
1431 DOOR CLOSER WITH STANDARD DUTY ARMS (WITHOUT HOLD OPEN) INSTALLATION INSTRUCTIONS 1431 SERIES ADJUSTABLE FROM SIZE 1 THRU 6 FOR INSTALLATION ASSISTANCE, CALL SARGENT AT 1-800-727-5477 www.sargentlock.com
More informationLeveling and Support. Support from UNITED is on the Level
Leveling and Support Support from UNITED is on the Level FST-LOK LMP ROUND BR Pg H2 SPRING JK LOKS Pg H10 STEEL SOKET LEVELING PDS Pg H12 USHIONED UNI-PDS Pg H17 FIXTURE JKS Pg H18 JIG LEVELING FEET &
More informationRWM4400UH High Performance Hand Held Wireless Microphone System
CH 1 CH 2 CH 3 CH 4 UHF QUAD VOLUME MAX VOLUME MAX VOLUME MAX VOLUME RWM 4400UH MIN MIN MIN CHANNEL 1 CHANNEL 2 CHANNEL 3 CHANNEL 4 RWM4400UH High Performne Hnd Held Wireless Mirophone System OWNER S MANUAL
More informationNORTH STAR 2-PANEL PATIO DOOR ASSEMBLY INSTRUCTIONS
40684 Talbot Line, St. Thomas, Ont., N5P 3T2 Phone: (59) 637-7899 Toll Free: (800) 265-570 Fax: (59) 637-3403 Web Site: www.northstarwindows.com NORTH STR 2-PNEL PTIO DOOR SSEMBLY INSTRUCTIONS I:\PDssembly\2Panel\CovPg.doc
More informationIPA FITTINGS FOR REHAU NORDIC DESIGN A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)
IP FITTINGS FOR REHU NORDIC DESIGN /S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ, DK-240 NIE TEL: (+45) 8 35 15 00 3 FITTINGS FOR REHU NORDIC DESIGN Table of contents Profile - REHU Nordic Design 4 PGE FITTINGS
More informationCustomer Helpline No. (01773)
Maintenane The ladder and all other wooden parts an be varnished to protet and extend its life. Lubriate all moving metal parts annually. Srews and nuts should be heked from time to time and tightened
More informationSpherical Buttons and Button Jig Feet
Spherical uttons and Jig Feet SPHERIL RIUS LOTOR UTTONS Spherical uttons and utton Jig Feet SPHERIL RIUS LOTOR UTTONS provide single point contact f irregular surfaces and are manufactured f Press Fit
More informationAssembly Instructions-C1 Amphenol UHF
Assemly Instrutions-C1 Amphenol UG STANDARD SOLDER TYPE PLUGS 83-1SP, 83-1SP-1050, 83-1SP-15RFX, 83-822 oupling ring plug su-ssemly Amphenol Connetor Cle Atthment Dt Stripping Dimensions, inhes (mm) Numer
More informationINSTALLATION GUIDE P57T15 PARTITION CURRENT TAHOE. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIE PT PRTITION 0 - URRENT THOE STRONG RELILE SEURE pro-gard.com 00.0.0 THESE OMPONENTS RE REQUIRE TO INSTLL THE PRTITION Hardware Kit Wing Kit PXXT PK WKT I. The following tools will be required
More informationIPA FITTINGS FOR ALUPLAST NORD-LINE A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)
IP FITTINGS FOR LUPLST NORD-LINE /S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ 9, DK-9240 NIE TEL: (+4) 98 3 1 00 3 FITTINGS FOR LUPLST NORD-LINE Table of Contents Profile - luplast Nord-Line 4 FITTINGS IP
More information670 Freestyle/Style Door with In-Line Panel
M 670 Freestyle/Style oor with In-Line Pnel Style Series Option Metl HK87 Slide MGNETIC PULL HNLE KIT with Mgnet Vinyl 083 JM E 989 MGNETIC OOR STOP N H900 PN HE SCREW C (CUH or MG) 781 HEER 716 HEER /
More informationET 51 EXTERIOR ROOF DRIP SIDE FINISH MOULDING INSTALLATION
EXTERIOR ROOF DRIP SIDE FINISH MOULDING 51 INSTALLATION The procedure descried elow is for the LH side. Use the sme procedure for oth the RH nd LH sides, unless otherwise specified. 1. INSTALL ROOF SIDE
More informationED5200(A) Series Rim Exit Devices
ED5200() Series Rim Exit Devices Installation Instructions (Single Doors or Pairs with Mullion) FM156 08/11 For Metal, omposite and Wood Doors of Either Hand End lamp (3) 8-32 x 5/16" Flat Head, Undercut
More informationDC3210. Recommended Closer Size
Installation Instructions For Non-Hold Open or A Hold Open Arm Option DC3200 Series Multi-Sized thru 6 Regular Arm Universal Door Closers Parallel Arm Jamb Mount See pages 2&3 See pages 4&5 See pages 6&7
More informationPANEL ASM-VALANCE AN0 ANGLE SCREW TRIM-FEATURE A SCREW 000G B (9) CAP-TRIM A A
PNEL SM-VLNE 9-0-N0 STEP SM-ELETRI 090-0-0 PNEL SM-VLNE 9-0-N0 PNEL SM-WHEEL LIP 9-0-0 NGLE-TTHMENT -0-0() NGLE --0() 000G9-0-U() 000G-0-U() RKET-WHEEL LIP -0-0 000G-0-0U 000G9-0-U() PNEL SM-VLNE 9-0-N0
More informationBrio. Weatherfold 5c 80. Codes B WC 4-80 S H SS. Sets all sets shown with hinge type H except BW2L/R-80SR. No finishes shown. Brio Weatherfold 5c
rio odes INSTW2 REV - JN 18 Weatherfold 5c 80 rio ustralia P: +61 2 87186718 W: brio.com.au E: brio.sales@allegion.com rio UK P: +44 191 2291224 W: briouk.com E: brio.sales.uk@allegion.com rio US P: +1
More informationAnalog Input Modules
7 922 nlog Input odules G56... nlog input modules for the ontrol of SQ5... ir dmper tutors y ontinuous nlog ontrol signls, suh s 4...20 m, nd ontinuous nlog position feedk signls. For supplementry Dt Sheets,
More informationTIMBER SLIDING LOFT LADDER
POWER ARM SPRING HOUSING ANCHOR & LOCATION STOP ROLLER AR TWIST CATCH TIMER SLIDING LOFT LADDER A1 A2 A6 Installation and Operating Instrutions Read Carefully efore Installation Please hek you have all
More informationPLEATED SCREEN INSTALLATION INSTRUCTIONS
PLETED SCREEN INSTLLTION INSTRUCTIONS DOC-II-PLETED Rev. 3 THNK YOU FOR PURCHSING LaCNTIN DOORS. INSTLLTION OF LaCNTIN PLETED SCREEN SYSTEM PLESE RED INSTRUCTIONS CREFULLY EFORE SSEMLING SCREEN SYSTEM.
More informationDETAIL A SCALE 1 : 85
ISIONS ZONE LTR. ESRIPTION TE PP - INITIL RELESE PER N NORTH.0 0 EST ISOLTE P (0" X.") 0 9 0 X FOOKE # 0 ENTER ISOLTE P (" X 9") WEST ISOLTE P (0" X.") FOOKE # 0. RWING ONTENTS SHEET : OVERLL LYOUT SHEET
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
PPLICTION: 2003-15 1500/2500/3500 HD SILVERDO/SIERR EXTENDED C/DOULE C/CREW C INCLUDING DIESEL EQUIPPED & 03-0 CLSSIC MODELS PRT # 5-5165, 5-5155 HDX RUNNING ORDS UTOMOTIVE PRODUCTS, INC. 1 INSTRUCTIONS
More informationElettra Evolution OK! OK! b. User manual
Elettr Evolution User mnul Pg. 1 INSTALLING THE SOLENOID VALVE. The progrmmle solenoi vlve is fully wtertight n will funtion even if instlle permnently uner wter t epth of up to one metre (IP68 ingress
More informationANTENNA-TPMS W/ EXT CABLE / SENSOR-WHEEL, TPMS / (8) 84 TO GROUND BAR
00 00 PIN HOUSING TO ELETRI STEP K,MP TO STEP SWITH PIN HOUSING TO STEP OVER 0 PIN HOUSING TO GENERTOR OIL 000 MM OF WIRE SM-HSSIS TO GENERTOR, GENERTOR STRTER LE, GENERTOR GROUN LE, & LE SM-GENERTOR HERE
More informationASSA ABLOY Series Installation Instructions. Regular Arm. Parallel Arm. Top Jamb Mount. Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models
9500 Series Installation Instructions Multi-Sized 1 thru 6 Non-Hold Open and Hold Open Models Regular Pages 5 & 6 Parallel Pages 7 & 8 Top Jamb Mount Pages 9 & 10 IMPORTANT: An improperly installed or
More informationSLOVAK UNIVERSITY OF TECHNOLOGY Faculty of Material Science and Technology in Trnava. ELECTRICAL ENGINEERING AND ELECTRONICS Laboratory exercises
SLOVAK UNIVERSITY OF TECHNOLOGY Fulty of Mteril Siene nd Tehnology in Trnv ELECTRICAL ENGINEERING AND ELECTRONICS Lbortory exerises Róbert Riedlmjer TRNAVA 00 ELECTRICAL ENGINEERING AND ELECTRONICS Lbortory
More informationTUR DOORS SHOWER DOORS
TUR DOORS SHOWER DOORS INSTALLATION INSTRUCTIONS TUB DOORS: LBTDB6062 SHOWER DOORS: LBSDB4876 LBSDB6076 VERSION: 3.2 PREPARATION FOR INSTALLATION TUB DOORS SHOWER DOORS PREPARATION FOR INSTALLATION READ
More informationMODEL SETUP & OPERATION MANUAL #25-300QC M1. 14 x 30 WOOD LATHE FEATURES SPECIFICATIONS
SETUP & OPERTION MNUL FETURES Heavy-duty cast-iron bed for stability and minimal vibration. Heavy-duty cast-iron stand. Headstock pivots 360 with positive stops at 45, 90, 135 and 180 for multi-position
More informationREMOTE IR/LED MODULE REMOTE 3 REVISION HISTORY C DETAIL A SCALE 1 : 1.5 I\O PANEL - SHEET 1 OF 6 ECO ZONE REV. DESCRIPTION DATE APPR'D
00000 ISION HISTORY EO ZONE. ESRIPTION TE PPR'. 9...0 IR 0 0.. LE INITOR LNSPE WLL MOUNT HNGERS REMOTE IR/LE MOULE REMOTE. 0 PORTRIT WLL MOUNT HNGERS SERVIE PNEL KEEP PERFORTE RES LER FOR IRFLOW. 9..0..
More informationMODEL SETUP & OPERATION MANUAL # DELUXE ROUTER TABLE KIT (Bench top model)
SETUP & OPERTION MNUL FETURES Heavy-duty massive router lift with 9 1/4" x 11 3/4" aluminum top plate. Stable 4 post/lift screw design & chain drive lifting system controlling all 4 corners simultaneously.
More information316R Series Installation Instructions
316R Series Installation Instructions Multi size 1 thru 6 Non hold open closers CAUTION An incorrectly installed or improperly adjusted closer can cause property damage or personal injury. These instructions
More informationMaintenance and other important non-personal injury and non-material damage instructions or statements that should be observed.
VIGO INDUSTRIES INSTLLTION GUIDE FOR SHOWER ENLOSURE ()! SFETY PREUTIONS This Installation Guide uses the following symbols to indicate important information. lways observe the instructions indicated by
More informationPacking List MODEL TEL-IAL-481 For Inactive Leaf TRIDENT double door
Items: SECURITECH GROUP, INC. MP uxiliary POLICE LOCK Packing List MODEL TEL-IL-481 For Inactive Leaf TRIDENT double door Items with * are pre-installed or assembled Fasteners: Part# Qty Name Description/Usage
More informationIPA FITTINGS FOR VEKA DANLINE 70 A/S J. PETERSENS BESLAGFABRIK JACOB PETERSENSVEJ 9, DK-9240 NIBE TEL: (+45)
IP FITTINGS FOR VEK DNLINE 70 2012 /S J. PETERSENS ESLGFRIK JCO PETERSENSVEJ 9, DK-9240 NIE TEL: (+4) 98 3 1 00 3 FITTINGS FOR VEK DNLINE 70 Table of Contents PGE Profile - VEK Danline 70 4 Suggestion
More informationDO NOT SCALE DRAWING TITLE: AWNING INSTL 100-SERIES
0 RKET-SUPPORT,WNING -0-HT () RKET-SUPPORT,WNING -0-HT 0 0 0-0-0U () 9-0-00U () 0 0 VIEW -INSERT 9-0-000 () -0-U () SETION E-E FILM-URETHNE,PROTETNT 090-0-000 (0mm) (ENTER ELOW WNING RNK OUTLET ON VN SIEWLL)
More informationOperation Manual. Product Code 885-V51. Computerized Embroidery Machine GETTING READY EMBROIDERY APPENDIX
Computerized Emroidery Mhine Opertion Mnul Produt Code 885-V51 GETTING READY EMBROIDERY APPENDIX Plese visit us t http://solutions.rother.om where you n get produt support nd nswers to frequently sked
More informationGENERAL NOTES 1600 SYSTEM NOTES STRUCTURAL SEAL NOTES 1 - HANDLING, STORING AND PROTECTING ALUMINUM MATERIAL. 2 - GENERAL RULES
GENERL NOTES 162-971 1 OF 12 THESE INSTLLTION INSTRUCTIONS RE SUPPLEMENT TO THE PPROVED SHOP DRWINGS. USE IN CONJUNCTION WITH THOSE DRWINGS. 1 - HNDLING, STORING ND PROTECTING LUMINUM MTERIL. THE FOLLOWING
More informationInstallation and Assembly - Articulating Swivel Double-Arm for 42" - 71" Plasma Screens
Installation and ssembly - rticulating Swivel Double-rm for 42" - 71" Plasma Screens Models: PLV 70, PLV 70-S R This product is UL Listed. It must be installed by a qualified professional installer. Maximum
More information6 BAY AV CREDENZA WITH DUAL DISPLAY MOUNT
D2/367M2 SSEMLY INSTRUCTIONS 6 Y V CREDENZ WITH DUL DISPLY MOUNT TIP HZRD WRNING! For use with video monitors weighing 175lbs (80kg) or less. Use with heavier televisions may result in instability causing
More informationTubing Spacers. Backing Plate. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a. a a a. a a. a a
Grnd Slm Instlltion Instructions TACO Metls Inc., 98 NE 179th Street Mimi, Florid 33162 hndyhnk@tcomrine.com tcomrine.com This Box Contins: 1- Port side Grnd Slm 1- Strbord side Grnd Slm 4-5/16 x 1 stinless
More informationEA FA. 1 OF / Dec-2017 NOTES:
00 00 M NTENN-TPMS W/ EXT LE 000090 / -0-000 RKET-MOUNTING,NTENN,TPMS 000090 / -0-HT 000G9-0-U () SENSOR-WHEEL, TPMS 000090 / 0-0-000 () PIN HOUSING TO ELETRI STEP K,MP TO STEP SWITH PIN HOUSING TO STEP
More informationLEXUS IS250/IS350 FRONT SPOILER Section I - Installation Preparation. Part Number: Section I - Installation Preparation.
Section I - Instlltion Preprtion Prt Numer: 0854-53830 Section I - Instlltion Preprtion Kit Contents 3 Description Front spoiler Hrdwre g Instruction mnul Additionl Items Required For Instlltion Conflicts
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Multi Line 6 x8 255x193x203cm / 100 1 /2 x76 x80 Poly-Tex, Inc. PO Box 458 27725 Dnville Avenue Cstle Rock, MN 55010 We Site: www.poly-tex.com English - 69717 Hoy Greenhouse Service
More informationPatterns and Algebra
Student Book Series D Mthletis Instnt Workooks Copyright Series D Contents Topi Ptterns nd funtions identifying nd reting ptterns skip ounting ompleting nd desriing ptterns numer ptterns in tles growing
More informationUltimate Flip Lever Astragal Prehanger Installation Instructions
Ultimte Flip Lever Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Tpe Mesure Kit Includes: Full Astrgl Full Length Trim Strip Screw Pck Field Pck
More informationAGA56... Analog Input Modules. Siemens Building Technologies HVAC Products
7 922 nlog Input odules G56... nlog input modules for the ontrol of SQ5... ir dmper tutors y ontinuous nlog ontrol signls, suh s 4...20 m, nd ontinuous nlog position feedk signls. For supplementry Dt Sheets,
More informationNOTICE. Six Foot (6') Step Ladder. Chalk Level 24" or 48" Saw Horses Claw Hammer
INSTLLTION INSTRUTIONS marr Manufactured Residential Steel Garage oors Lincoln 000 / Hillcrest 000 Fimbel Olympus 500-00 / Fimbel esigner s hoice 500-00 ottom racket (Left and Right) (Left Shown/ssembled)
More informationDFTR-ORIG XXX 427 CABINET ASM-PIPE COVER XXX
RELESE TE WG 00 INET SM-OVH,SHIRT,RH ZONE ISION REOR TE FTR-ORIG -0-XXX -0-XXX INET SM-WIRE OVER -0-XXX INET SM-TH 9-0-XXX INET SM-STORGE F-0-XXX -0-XXX INET SM-PIPE OVER 0-0-XXX TLE SM-INETTE,RN EN 9-0-XXX
More informationTP Series - Triple PV Top of Pole Solar LED Lighting System
TP Series - Triple PV Top of Pole Solr LED Lighting System Instlltion Mnul MKTG-TP34-02-EN-1113 Instlltion Mnul TP Series Importnt Notes nd Wrnings This instlltion nd instruction mnul provides instlltion
More informationNOTICE. Six Foot (6') Step Ladder. Chalk Level 24" or 48" Saw Horses Claw Hammer
o om racket (Le and Right) (Le Shown/ssembled) NGER High spring tension can cause serious injury or death. o not attempt to remove, repair, or adjust any springs, any RE colored fasteners, or the hardware
More informationInstallation Instructions. Installation Type
Installation Instructions 800 & 8050 Slide Track Door Closers Non Hold Open & Hold Open Models Note: Hold open models are not permitted to be installed in Listed fire door assemblies. PULL SIDE MOUNTED
More informationApplication. Finishes. Lamping Options T5. Features. Packaging 4 Bodies per skid 50. Optional Features
VILLE WITH EITHER SPE OR ULL NOSE EN PS SPE ULL NOSE pplication Open office ambient lighting for virtually glare free and shadow free illumination. Finishes are 20 gauge roll formed steel housing in solid
More informationDrywall Lift Storage & Transportation Cart Model 110 Patents Pending
Drywall Lift Storage & Transportation Cart Model 110 Patents Pending WRNING: When transporting, LWYS secure the PNELLIFT Model 110 cart in the vehicle to prevent shifting of the load while in transit.
More informationInstallation Instructions. Installation Type
Installation Instructions 300 & 3050 Slide Track Door Closers Non Hold Open & Hold Open Models Note: Hold open models are not permitted to be installed in Listed fire door assemblies. PULL SIDE MOUNTED
More informationThe Genius Sierra retractable screen features a fully assembled screen cassette pre-sized for
IT IS IGLY REOENDED TT TE INSTRUTIONS E RED TROUG EFORE INSTLLTION. RETRTLE SREEN DOOR SIERR 100 SINGLE DOOR installation instructions INSTLLTION TOOLS Phillips Screwdriver measuring tape and-eld or Power
More informationVERSION 2 #BB_0001. Four complete assemblies to be made for the following tests: RFQ Major Vane to Minor Vane. Joint Test Assemblies
#_000 RFQ Major Vane to Minor Vane Joint Test ssemblies F RONT EN TEST STN (F.E.T.S.) SETION - SIE F F VERSION G G Number off: omplete ssemblies Hole centres: `0.0 mm Scale: o not scale rawing number:
More informationUltimate Trilennium Astragal Prehanger Installation Instructions
Ultimte Trilennium Astrgl Prehnger Instlltion Instructions Tools Required: Flthed Screwdriver Shers Phillips Screwdriver Power Drill with 1" Drill Bit Tpe Mesure 1" Spde Bit Kit Includes: Full Astrgl Full
More informationDRAWER BASE DRAWING TABLE
MODEL VIEWS MY NOT REPRESENT EXCT MODEL PURCHSED B UPD STEP 1 NME ECN NO. : : : DIMENSION RE IN INCHES 1 OF 10 K:\DIVERSIFIED\\CD\.dwg, 9/25/2018 9:04:08 M, DWG To PDF.pc3 TOOLS REQUIRED 1 2 " WRENCH 1
More informationINSTALLATION MANUAL. English Edition D75X ULTRA SHORT SERIES
INSTLLTION MNUL English Edition D75X ULTR SHORT SERIES SFETY INSTRUCTION For your safety, please read the instruction before using the wall mount bracket. ny improper disposition caused by ignoring this
More informationINFINITY PERFORMANCE LED
2016 INFINITY PERFORMNE LED PE 3 P5002 P5004 P5006 PE 4 P5014 PE 5 P5020 P5022 Drawing: 762270XX Rev: Sheet: 1 of 10 Eng: LD Date Drawn: 07/19/17 TLE OF ONTENTS PE 3 (URVED) P5002, P5004, P5006 INSTRUTIONS
More informationKEY LARGO SECTIONAL SOFA SET
TM Use and are uide KEY LRO SETIONL SOF SET Product ode: D7 M2073 KSN: 08824327-4 UP ode: 885227002743 Date of Purchase: / / Thank you for your purchase Thank you for your purchase! We are pleased that
More informationOperation Manual GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX. Computerized Sewing Machine
GETTING READY SEWING BASICS UTILITY STITCHES APPENDIX Opertion Mnul Computerized Sewing Mhine Importnt Sfety Instrutions Plese red these sfety instrutions efore ttempting to use the mhine. This mhine is
More informationASSEMBLY INSTRUCTIONS 5PC Storage Dining Set
ASSEMLY INSTRUTIONS 5P Storge Dining Set Sers Stock # 56170 VL Stock #07-2204 U S T O M E R S E R V I E I N F O R M AT I O N Victory Lnd Group, Inc 1350 Munger Rd rtlett, IL 60103 WE: http://www.victorylndgroup.com
More information