Low-Voltage, Dual SPDT, Audio Clickless Switches with Negative Rail Capability
|
|
- Caitlin Payne
- 5 years ago
- Views:
Transcription
1 19-563; Rev 1; 11/6 Low-Voltage, Dual SPDT, Audio Clickless General Description The MAX4744/MAX4744H/MAX4745/MAX4745H/ dual SPDT (single-pole/double-throw) audio switches feature negative signal capability that allows signals as low as - 5.5V to pass through without distortion. These analog switches have a low on-resistance and low supply current, and operate from a single +1.8V to +5.5V supply. The MAX4744/MAX4744H have internal shunt resistors that automatically discharge the capacitance at the normally open (NO) and normally closed (NC) terminals when they are not connected. The features internal shunt resistors on NC_ terminals. This reduces click-and-pop sounds that occur when switching audio signals between precharged points. A break-beforemake feature further reduces popping. The MAX4744/ MAX4745 control the switches with two control bits CB1 and CB2. The MAX4744H/MAX4745H/ have one control bit to switch both switches and an enable input EN to put the switches in a high-impedance mode. The MAX4744H/MAX4745H/ also have an internal protection network against voltages applied to COM_ when = V. These devices are available in a space-saving 1-pin µdfn (2mm x 2mm) package and operate over the -4 C to +85 C extended temperature range. Speaker Switching Power Routing Cellular Phones MP3 Players PDAs and Other Handheld Devices Notebook Computers PART PIN- PACKAGE Applications TOP MARK Features Distortion-Free Negative Signal Throughput Down to - 5.5V Internal Shunt Resistor Reduces Click/Pop (MAX4744/MAX4744H).6Ω (typ) Low On-Resistance.1Ω (max) Channel-to-Channel Matching.55Ω (max) On-Resistance Flatness +1.8V to +5.5V Single-Supply Voltage.1% (typ) Total Harmonic Distortion -75dB (typ) Crosstalk (1kHz) -68dB (typ) Off-Isolation (1kHz) Available in 1-Pin µdfn Package (2mm x 2mm) TOP VIEW COM1 NC1 NC2 COM MAX4744 MAX CB1 NO1 NO2 CB2 μdfn (2mm x 2mm) Pin Configurations COM1 NC1 NC2 COM MAX4744H MAX4745H EN NO1 NO2 CB μdfn (2mm x 2mm) Ordering Information/Selector Guide CLICKLESS COM PROTECTION PKG CODE MAX4744ELB+T 1 µdfn-1 +AAF Yes No L122-1 MAX4744HELB+T 1 µdfn-1 +AAG Yes Yes L122-1 MAX4745ELB+T 1 µdfn-1 +AAH No No L122-1 MAX4745HELB+T 1 µdfn-1 +AAI No Yes L122-1 ELB+T 1 µdfn-1 +AAM Yes, on NC_ Yes L122-1 Note: All devices are specified over the -4 C to +85 C operating temperature range. +Denotes a lead-free package. Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at , or visit Maxim s website at
2 ABSOLUTE MAXIMUM RATINGS (All voltages referenced to.),, EN...-.3V to +6.V NC_, NO_...( - 6V) to ( +.3V) COM_ (MAX4744/MAX4745)...( - 6V) to ( +.3V) COM_ (MAX4744H/MAX4745H/)...(Note 1) Continuous Current NO_, NC_, COM_....±3mA Peak Current NO_, NC_, COM_ (pulsed at 1ms, 5% duty cycle)...±4ma Peak Current NO_, NC_, COM_ (pulsed at 1ms, 1% duty cycle)...±5ma ESD Protection per Method NO_, NC_, COM_,,,, EN...±2kV Continuous Power Dissipation (T A = +7 C) 1-Pin µdfn (derate 5mW/ C above +7 C)...43mW Operating Temperature Range...-4 C to +85 C Storage Temperature Range C to +15 C Note 1: If >.5V, limits are ( - 6V) to ( +.3V). If <.5V, limits are ( - 6.V) to +6.V. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS ( = +2.7V to +5.5V, T A = -4 C to +85 C, unless otherwise noted. Typical values are at = 3.3V, T A = +25 C.) (Note 2) POWER SUPPLY PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Supply-Voltage Range V = 5.5V, V CB _ = V or.3 1 Supply Current I CC = 5.5V, V CB _ =.5V or 1.4V 8 = 2.7V, V =.5V or 1.4V 4 ANALOG SWITCH Analog Signal Range V NC _, V NO _, V COM _ (Note 3) On-Resistance (Note 4) R ON = - 5.5V, -1V, V, 1V, = +2.7V; V NC_ or V NO _ 2V, ; I COM_ = 1mA On-Resistance Match Between Channels (Notes 4 and 5) ΔR ON V C C = 2.7V, V N C _ or V N O _ = V, I C OM _ = 1m A On-Resistance Flatness (Note 6) R FLAT V C C - 5.5V, - 1V, V, 1V, 2V, V C C = + 2.7V, V N C _ or V N O _ = V C C ; I C OM _ = 1m A Shunt Switch Resistance R SH MAX4744/MAX4744H/ only, = 2.7V NC_, NO_ Off-Leakage Current (Note 3) COM_ On-Leakage Current (Note 3) I NO_(OFF), I NC_(OFF) V C C = + 2.7V sw i tch op en; V N C _ or V N O _ = - 2.5V, + 2.5V ( M AX 4745/M AX 4745H onl y) ( M AX 4746H - I N O_ ( OFF ) onl y) I COM_(ON) V C C = 2.7V sw i tch cl osed ; V N C _ or V N O _ = - 2.5V, + 2.5V ; V C OM _ = - 2.5V, + 2.5V - 5.5V T A = +25 C.6.95 T A = T MIN to T MAX 1. T A = +25 C.1 T A = T MIN to T MAX.1 T A = +25 C.55 T A = T MIN to T MAX.6 µa V Ω Ω Ω 2 5 kω T A = +25 C T A = T MIN to T MAX T A = +25 C T A = T MIN to T MAX na na 2
3 ELECTRICAL CHARACTERISTICS (continued) ( = +2.7V to +5.5V, T A = -4 C to +85 C, unless otherwise noted. Typical values are at = 3.3V, T A = +25 C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS COM_ Leakage Under Protection Conditions DYNAMIC CHARACTERISTICS I L(PROT) = V; V COM _ = +5.5V; V NC _ and V NO _ are unconnected or connected to ; V CB _ = V (MAX4744H/MAX4745H/ only) T A = +25 C 3 T A = T MIN to T MAX 5 For N O_, V N O_ = 1.5V, V C C = 2.7V, 55 V C B_ = V to V C C Turn-On Time t ON R L = 32Ω, C L = 35p F, Fi g ur e 2 For N C _, V N C _ = 1.5V, 56 V C B_ = V C C to V Turn-Off Time t OFF 32Ω, C L = 35pF, = 2.7V, R L = For N O_, V N O_ = 1.5V, V C B_ = V C C to V 54 Figure 2 For N C _, V N C _ = 1.5V, V C B_ = V to V C C 36 Break-Before-Make Delay Time t D V CB _ = to V; for NC_, V CB _ = V to = 2.7V, V NC _ = V NO_ = 1.5V; for NO_, ; R L = 32Ω; C L = 35pF; Figure 3 Power-Supply Rejection Ratio PSRR f = 1kHz, V COM _ = 1V RMS, R L = 5Ω, C L = 5pF na ns ns 2 ns 52 db Charge Injection Q V GEN _ = V; R GEN = Ω, C L = 1nF, Figure 4 45 pc Off-Isolation V ISO C L = 5pF; R L = 5Ω; f = 1kHz; V COM _ = 1V RMS ; Figure 5 (Note 7) Crosstalk V CT C L = 5pF; R L = 5Ω; f = 1kHz; V COM _ = 1V RMS ; Figure 5 Total Harmonic Distortion NO_, NC_ Off-Capacitance THD f = 2Hz to 2kHz, V COM_ =.5V P-P, R L = 5Ω -68 db -75 db.1 % C NO_(OFF), C NC_(OFF) f = 1MHz, Figure 6 9 pf COM On-Capacitance C COM_(ON) f = 1MHz, Figure 6 3 pf 3
4 ELECTRICAL CHARACTERISTICS (continued) ( = +2.7V to +5.5V, T A = -4 C to +85 C, unless otherwise noted. Typical values are at = 3.3V, T A = +25 C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DIGITAL INPUTS (, EN) Input-Logic High V IH 1.4 V Input-Logic Low V IL.5 V Input Leakage Current I LEAK V CB _ or V EN = V or µa Note 2: All parameters are production tested at T A = +25 C and guaranteed by design over the specified temperature range. Note 3: Signals on COM_, NO_, or NC_ exceeding are clamped by internal diodes. Limit forward-diode current to maximum current ratings. Note 4: Guaranteed by design; not production tested. Note 5: ΔR ON = R ON(MAX) - R ON(MIN). Note 6: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal ranges. Note 7: Off-isolation = 2log 1 [V COM_ / V NO_ ], V COM_ = output, V NO_ = input to off switch. ( = +3.3V, T A = +25 C, unless otherwise noted.) ON-RESISTANCE (Ω) ON-RESISTANCE vs. COM VOLTAGE = +1.8V = +3V = +5V COM VOLTAGE (V) MAX4744 toc1 ON-RESISTANCE (Ω) = 3V ON-RESISTANCE vs. COM VOLTAGE T A = +85 C T A = +25 C T A = -4 C COM VOLTAGE (V) Typical Operating Characteristics MAX4744 toc2 ON-RESISTANCE (Ω) = 5V ON-RESISTANCE vs. COM VOLTAGE T A = +85 C T A = +25 C T A = -4 C COM VOLTAGE (V) MAX4744 toc3 4
5 ( = +3.3V, T A = +25 C, unless otherwise noted.) TIME (ns) TURN-ON/TURN-OFF TIME (ns) NC_ TURN-ON/NO_ TURN-OFF TIME vs. SUPPLY VOLTAGE NC_ TURN-ON TIME NO_ TURN-OFF TIME SUPPLY VOLTAGE (V) NO_ TURN-ON/NC_ TURN-OFF TIME vs. TEMPERATURE TEMPERATURE ( C) COM PROTECTION LEAKAGE CURRENT (na) NC_ t ON NO_ t OFF MAX4744 toc4 5.5 MAX4744 toc7 TIME (ns) THRESHOLD (V) COM PROTECTION LEAKAGE CURRENT vs. SUPPLY VOLTAGE T A = -4 C T A = +25 C T A = +85 C SUPPLY VOLTAGE (V) NO_ TURN-ON/NC_ TURN-OFF TIME vs. SUPPLY VOLTAGE NO_ TURN-ON TIME NC_ TURN-OFF TIME SUPPLY VOLTAGE (V) THRESHOLD vs. SUPPLY VOLTAGE SUPPLY VOLTAGE (V) MAX4744 toc1 V RISING V FALLING Typical Operating Characteristics CHARGE INJECTION (pc) MAX4744 toc5 MAX4744 toc8 5.5 TURN-ON/TURN-OFF TIME (ns) SUPPLY CURRENT (μa) NO_ TURN-ON/NC_ TURN-OFF TIME vs. TEMPERATURE NO_ t ON NC_ t OFF TEMPERATURE ( C) SUPPLY CURRENT vs. -INPUT VOLTAGE DIGITAL INPUT VOLTAGE (V) CHARGE INJECTION vs. SUPPLY VOLTAGE SUPPLY VOLTAGE (V) MAX4744 toc MAX4744 toc6 MAX4744 toc9 5
6 Typical Operating Characteristics (continued) ( = +3.3V, T A = +25 C, unless otherwise noted.) LEAKAGE CURRENT (na) OFF-ISOLATION (db) THD (%) OFF-ISOLATION vs. FREQUENCY LEAKAGE CURRENT vs. TEMPERATURE FREQUENCY (MHz) TOTAL HARMONIC DISTORTION vs. FREQUENCY FREQUENCY (khz) ON OFF TEMPERATURE ( C) MAX4744 toc12 MAX4744 toc14 MAX4744 toc16 ON-LOSS (db) CROSSTALK (db) PSRR (db) CROSSTALK vs. FREQUENCY FREQUENCY RESPONSE FREQUENCY (MHz) FREQUENCY (MHz) POWER-SUPPLY REJECTION RATIO vs. FREQUENCY FREQUENCY (MHz) MAX4744 toc13 MAX4744 toc17 MAX4744 toc15 6
7 MAX4744/ MAX4745 PIN MAX4744H/ MAX4745H/ NAME 1 CB1 Digital Control Input for Analog Switch 1 Detailed Description The MAX4744/MAX4744H/MAX4745/MAX4745H/ are low on-resistance, low-voltage, dual- SPDT analog switches that operate from a +1.8V to +5.5V single supply. These devices feature a negative signal capability that allows signals as low as - 5.5V to pass through without distortion. The MAX4744/MAX4745 feature two digital control bits to control each switch independently (see Table 1). The MAX4744H/MAX4745H/ have one control bit to switch both switches and an enable input EN to put the switches in a high-impedance mode. Driving EN low takes the switches out of high impedance and CB controls both switches (see Table 2). The MAX4744/MAX4744H have internal shunt resistors on all NO and NC terminals, and the has internal shunt resistors on NC terminals to suppress click-and-pop sounds that can occur when switching audio signals between precharged points. Applications Information Digital Control Inputs The MAX4744/MAX4744H/MAX4745/MAX4745H/ logic inputs accept up to +5.5V, regardless of supply voltage. For example, with a +3.3V supply, CB, CB1, CB2, and EN can be driven low to and FUNCTION Pin Description 1 EN Enable Input. Driving EN high causes all switches to be high impedance. Pull EN low for normal operation. 2 2 NO1 Analog Switch 1 Normally Open Terminal 3 3 Ground 4 4 NO2 Analog Switch 2 Normally Open Terminal 5 CB2 Digital Control Input for Analog Switch 2 5 CB Digital Control Input for Analog Switches 1 and COM2 Analog Switch 2 Common Terminal 7 7 NC2 Analog Switch 2 Normally Closed Terminal 8 8 Positive Supply Voltage from +1.8V to +5.5V 9 9 NC1 Analog Switch 1 Normally Closed Terminal 1 1 COM1 Analog Switch 1 Common Terminal Table 1. MAX4744/MAX4745 Truth Table CONTROL SWITCH STATE CB1 CB2 Switch 1 Switch 2 Connected to NC1 Connected to NC2 1 Connected to NC1 Connected to NO2 1 Connected to NO1 Connected to NC2 1 1 Connected to NO1 Connected to NO2 Table 2. MAX4744H/MAX4745H/ Truth Table CONTROL SWITCH STATE EN CB Switch 1 Switch 2 Connected to NC1 Connected to NC2 1 Connected to NO1 Connected to NO2 1 X High Impedance High Impedance X = Don t Care high to +5.5V, allowing for mixed logic levels in a system. Driving CB, CB1, CB2, and EN rail-to-rail minimizes power consumption. 7
8 NC1 NO1 SHUNT SWITCH NC2 NO2 NC1 NO1 NC2 NO2 MAX4744 SWITCH 1 SWITCH 2 MAX4745 SWITCH 1 SWITCH 2 NO1 NC1 SHUNT SWITCH NC2 NO2 COM1 CB1 CB2 COM2 COM1 CB1 CB2 COM2 HIGH-Z HIGH-Z CONTROL NC1 NO1 SHUNT SWITCH NC2 NO2 NC1 NO1 NC2 NO2 SWITCH 1 SWITCH 2 EN CB HIGH-Z HIGH-Z HIGH-Z HIGH-Z COM1 COM2 MAX4744H MAX4745H CONTROL SWITCH 1 CONTROL SWITCH 1 SWITCH 2 SWITCH 2 EN CB COM1 EN CB COM2 COM1 COM2 Figure 1. Functional Diagram 8
9 MAX4744/MAX4745/ MAX4744H/MAX4745H/ V NC_ OR V NO_ INPUT Figure 2. Switching Time MAX4744/MAX4745/ MAX4744H/MAX4745H/ V NC_ = V NO_ INPUT NO_ OR NC_ COM_ C L INCLUDES FIXTURE AND STRAY CAPACITANCE = V N_ ( R L R L + R ON ) NC_ NO_ Analog Signal Levels These devices pass signals from to as low as - 5.5V, including signals below ground with minimal distortion and very little change in on-resistance (see the Typical Operating Characteristics). The switches are bidirectional, so the NO_, NC_, and COM_ terminals can be used as either inputs or outputs. COM_ Protection with = V (MAX4744H/MAX4745H/) This feature prevents any damage to the device due to improper power-supply sequencing. The protection applies if a signal is applied on COM_ when is less than.5v. The switch is not protected if goes above.5v due to parasitic capacitive coupling or any Figure 3. Break-Before-Make Interval COM_ C L INCLUDES FIXTURE AND STRAY CAPACITANCE R L R L C L C L INPUT SWITCH OUTPUT Test Circuits/Timing Diagrams INPUT V V V 5% t ON tr < 5ns tf < 5ns leakage between COM_ and. The signal at COM_ ranges between ( - 6.V) to 6.V under protection conditions. Click-and-Pop Suppression The MAX4744/MAX4744H have a shunt resistor on all their NO and NC terminals to automatically discharge any capacitance when they are not connected to COM. The shunt resistor reduces audible click-and-pop sounds that occur when switching between audio sources. Audible clicks and pops are caused when a step DC voltage is switched into the speaker. The DC step transients can be reduced by automatically discharging the side that is not connected to the COM terminal, reducing any residual DC voltage and reducing clicks and pops. t OFF.8 x V UT.2 x IN DEPENDS ON SWITCH CONFIGURATION; INPUT POLARITY DETERMINED BY SENSE OF SWITCH. 5% t BBM.9 x 9
10 MAX4744/MAX4745/ MAX4744H/MAX4745H/ Figure 4. Charge Injection V OR NC_ COM_ Break-Before-Make Switching All devices feature break-before-make switching, which is configured to break (open) the first set of contacts before engaging (closing) the new contacts. This prevents the momentary connection of the old and new signal paths to the output, reducing click-and-pop sounds. 1nF MAX4744 MAX4744H COM_ NC_ OR NO_ V IL TO V IH MEASUREMENTS ARE STANDARDIZED AGAINST SHORT AND OPEN AT SOCKET TERMINALS. OFF-ISOLATION IS MEASURED BETWEEN COM_ AND OFF NO_ OR NC_ TERMINALS. ON-LOSS IS MEASURED BETWEEN COM_ AND ON NO_ OR NC_ TERMINAL ON EACH SWITCH. CROSSTALK IS MEASURED FROM ONE CHANNEL TO THE OTHER CHANNEL. SIGNAL DIRECTION THROUGH SWITCH IS REVERSED; WORST VALUES ARE RECORDED. Figure 5. Off-Isolation, On-Loss, and Crosstalk NO_ C L V IN MEAS VOUT NETWORK ANALYZER 5Ω 5Ω 5Ω Test Circuits/Timing Diagrams OFF OFF REF 5Ω ON ON Q = (Δ )(C L ) Δ Power-Supply Sequencing and Overvoltage Protection Caution: Do not exceed the Absolute Maximum Ratings since stresses beyond the listed ratings may cause permanent damage to the device. Proper power-supply sequencing is recommended for all CMOS devices. Improper supply sequencing can force the switch into latch-up, causing it to draw excessive supply current. The only way out of latch-up is to recycle the power and reapply properly. Connect all ground pins first, then apply power to, and finally apply signals to NO_, NC_, and COM_. Follow the reverse order upon power-down. OFF OFF INPUT WAVEFORMS INVERTED FOR SWITCHES THAT HAVE THE OPPOSITE SENSE. OFF-ISOLATION = 2log OFF-LOSS = 2log CROSSTALK = 2log V IN V IN V IN 1
11 CAPACITANCE ANALYZER f = 1MHz 1nF COM_ NC_ OR NO_ Figure 6. Channel Off-/On-Capacitance PROCESS: BiCMOS MAX4744 MAX4744H MAX4745 MAX4745H V IL OR V IH Chip Information MAXIM DirectDrive AUDIO AMP AUDIO Typical Operating Circuit NC1 NO1 NC2 NO2 MAX4744 SHUNT SWITCH COM1 CB1 CB2 COM2 11
12 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to D XXXX XXXX XXXX PIN 1 INDEX AREA -DRAWING NOT TO SCALE- SAMPLE MARKING 7 A1 COMMON DIMENSIONS SYMBOL MIN. NOM. MAX. A A1 A D E L L1.1 REF. PACKAGE VARIATIONS PKG. CODE N e b L BSC.3±.5 L822-1 L E A.5 BSC.4 BSC.25±.5.2±.3 b A A2 (N/2-1) x e 1.3 REF. 1.5 REF. 1.6 REF. L L C L e e EVEN TERMINAL A A (N/2-1) x e) b N 1 e C L ODD TERMINAL PACKAGE OUTLINE, 6, 8, 1L udfn, 2x2x.8 mm SOLDER MASK COVERAGE PACKAGE OUTLINE, 6, 8, 1L udfn, 2x2x.8 mm -DRAWING NOT TO SCALE A 2 2 PIN 1.1x45 L1 L A 1 2 6, 8, 1L UDFN.EPS Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 Maxim Integrated Products, 12 San Gabriel Drive, Sunnyvale, CA Maxim Integrated Products is a registered trademark of Maxim Integrated Products, Inc. CARDENAS
Low-Voltage, Dual SPDT, Audio Clickless Switches With Negative Rail Capability
19-563; Rev ; 5/6 Low-Voltage, Dual SPDT, Audio Clickless General Description The dual SPDT (single pole/double throw) audio switches feature negative signal capability that allows signals as low as -
More informationMAX4740ETE+ MAX4740EVE+ MAX4740HETE+ MAX4740HEVE+ TOP VIEW INTERNAL SPEAKER EXTERNAL HEADPHONES COM4 EXTERNAL HEADPHONES
19-558; Rev 1; 11/7 Quad SPDT Audio Switches General Description The low on-resistance (.61Ω typ) analog switches operate from a single 1.6V to 5.5V supply. The are quad, singlepole, double-throw (SPDT)
More informationDual SPDT Negative Rail Analog Switches with ±VCC Capability
19-4244; Rev 1; 12/8 EVALUATION KIT AVAILABLE Dual SPDT Negative Rail Analog Switches General Description The MAX1454/MAX1455/MAX1455A/MAX1456 dual single-pole/double-throw (SPDT) audio switches feature
More information0.8Ω, Low-Voltage, Single-Supply Dual SPST Analog Switches
19-116; Rev ; 1/6.Ω, Low-Voltage, Single-Supply Dual SPST General Description The are low on-resistance, low-voltage, dual single-pole/single-throw (SPST) analog switches that operate from a single +1.6V
More informationLow-RON, Dual-SPST/Single-SPDT Clickless Switches with Negative Rail Capability
9-3775; Rev 2; 5/6 Low-RON, Dual-SPST/Single-SPDT Clickless General Description The switches feature negative signal capability that allows signals below ground to pass through without distortion. The
More informationMAX4684/MAX4685 OFF ON 1 SWITCHES SHOWN FOR LOGIC "0" INPUT
19-1977; Rev 4; 1/9.5Ω/.8Ω Low-Voltage, Dual SPDT General Description The low on-resistance (R ON ), lowvoltage, dual single-pole/double-throw (SPDT) analog switches operate from a single +1.8V to +5.5V
More informationTOP VIEW COUT1 COM2. Maxim Integrated Products 1
19-77; Rev ; 7/4.75Ω, Dual SPDT Audio Switch with General Description The dual, single-pole/double-throw (SPDT) switch operates from a single +2V to +5.5V supply and features rail-to-rail signal handling.
More information20Ω, 300MHz Bandwidth, Dual SPDT Analog Switch in UCSP
9-2626; Rev ; /2 2, 3MHz Bandwidth, Dual SPDT Analog General Description The low-voltage, low on-resistance (R ON ), dual single-pole/double throw (SPDT) analog switch operates from a single +.8V to +5.5V
More informationTOP VIEW COM2. Maxim Integrated Products 1
19-3472; Rev ; 1/4 Quad SPST Switches General Description The quad single-pole/single-throw (SPST) switch operates from a single +2V to +5.5V supply and can handle signals greater than the supply rail.
More informationQuad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
19-2418; Rev ; 4/2 Quad, Rail-to-Rail, Fault-Protected, General Description The are quad, single-pole/single-throw (SPST), fault-protected analog switches. They are pin compatible with the industry-standard
More informationPA R T NC1 A0 V+ EN CONTROL LOGIC A0 NC1 EN 1 MAX4674 COM2 QFN. Maxim Integrated Products 1
9-78; Rev 3; 2/6 3V/5V, 4Ω, Wideband Quad 2: Analog Multiplexer General Description The is a low-voltage CMOS analog switch containing four 2: multiplexers/demultiplexer. When powered from a single +5V
More informationON SWITCH NONE COM-NO0 COM-NO1 COM-NO2 COM-NO3 ADDA ADDB X = DON T CARE N.C. = NO CONNECT
9-224; Rev ; /8 Low-Voltage, 6, 4: Analog Multiplexer in QFN General Description The MAX474 low-voltage, 4-channel analog multiplexer operates from a single +.8V to +.V supply. The MAX474 features break-before-make
More information2.5Ω, Low-Voltage, SPST/SPDT Analog Switches in UCSP Package
19-242; Rev 1; 2/3 2.5Ω, Low-Voltage, SPST/SPDT General Description The low on-resistance (R ON ), low-voltage analog switches operate from a single +1.8V to +5.5V supply. The / are single-pole/single-throw
More informationLow-Voltage, Dual SPDT, Audio Clickless Switches with Negative Rail Capability
9-352; Rev 2; /6 Low-Voltage, Dual SPDT, Audio Clickless General Description The dual SPDT (single-pole/double-throw) switches feature negative signal capability that allows signals below ground to pass
More information0.6Ω, Low-Voltage, Single-Supply, Dual SPDT Analog Switch
.6Ω, Low-Voltage, Single-Supply, Dual SPDT General Description The is a low on-resistance, low-voltage, dual single-pole/double throw (SPDT) analog switch that operates from a single 1.6V to 4.2V supply.
More information50Ω, Low-Voltage, Quad SPST/Dual SPDT Analog Switches in WLP
9-266; Rev 3; /2 5Ω, Low-Voltage, Quad SPST/Dual SPDT Analog General Description The low-voltage, quad single-pole single-throw (SPST)/dual single-pole/double-throw (SPDT) analog switches operate from
More informationMultiplexers/Switches
EVALUATION KIT AVAILABLE / General Description The / are low-voltage, single-supply CMOS analog switches configured as a 4-channel multiplexer/demultiplexer () and a double-pole/double-throw (DPDT) switch
More informationPART MAX4503CPA MAX4503CSA. Pin Configurations 1 5 V+ COM N.C. V+ 4 MAX4504 MAX4503 DIP/SO
9-064; Rev ; /07 Low-Voltage, Dual-Supply, SPST, General Description The are low-voltage, dual-supply, single-pole/single-throw (SPST), CMOS analog switches. The is normally open (NO). The is normally
More informationPin Configurations/Functional Diagrams/Truth Tables COM SC70-6 SC70-6 PIN 5 5 XYZ NOTE: SC70-5 PACKAGE HAS LETTERING NEAREST PIN 5.
9-359; Rev ; / General Description The MAX76/MAX77 single-pole/single-throw (SPST) switches operate from a single.8v to 5.5V supply. The MAX76 is a normally closed (NC) switch and the MAX77 is the normally
More informationPin Configurations/Functional Diagrams/Truth Table COM COM GND MAX4644 OFF OFF. Maxim Integrated Products 1
9-7; Rev ; 3/ High-Speed, Low-Voltage, 4Ω, General Description The is a single-pole/double-throw (SPDT) switch that operates from a single supply ranging from +.8V to +.V. It provides low 4Ω on-resistance
More information10Ω, Quad, SPST, +3V Logic-Compatible Analog Switches
19-218; Rev 1; 9/8 1Ω, Quad, SPST, +3V Logic-Compatible General Description Maxim s analog switches feature low on-resistance (1Ω max) and 1.5Ω onresistance matching between channels. These switches are
More information3.5Ω/7Ω Quad SPST Switches with Over-Rail Signal Handling
19-71; Rev ; 1/.5Ω/7Ω Quad SPST Switches with Over-Rail General Description The MAX851/MAX851H/MAX85/MAX85H family of quad single-pole/single-throw (SPST) switches operates from a single +2V to +5.5V supply
More informationMAX4852 MAX4852H NC1 COM1 NO1 IN1 IN2 NC2 COM2 NO2. Maxim Integrated Products 1
19-7; Rev ; 7/ Dual SPDT Analog Switches with General Description The family of dual SPDT (single-pole/double-throw) switches operate from a single +V to +.V supply and can handle signals greater than
More informationLow-Voltage, High-Speed, Quad, SPST CMOS Analog Switches
9-5; Rev ; 7/99 Low-Voltage, High-Speed, Quad, SPST General Description The quad, low-voltage, high-speed, single-pole/single-throw (SPST) analog switches are pin compatible with the industry-standard
More informationMAX4680CWE. Pin Configurations/Functional Diagrams/Truth Tables N01 N.C. COM1 V- MAX4690 COM2 IN2 N.C. NO2 SSOP/SO/DIP SWITCH 2 ON OFF 1 OFF
19-1513; Rev ; 7/99 General Description The dual analog switches feature low on-resistance of 1.25Ω max. On-resistance is matched between switches to.3ω max and is flat (.3Ω max) over the specified signal
More informationMAX V Capable, Low-R ON, Beyond-the-Rails DPDT Analog Switch
Click here for production status of specific part numbers. MAX2327 12V Capable, Low-R ON, General Description The MAX2327 ultra-small, low-on-resistance (R ON ) double-pole/double-throw (DPDT) analog switches
More informationMAX4723EUA -40 C to +85 C 8 µmax MAX4722 MAX4723. Pin Configurations/Functional Diagrams/Truth Tables C NC1 IN1 UCSP. Maxim Integrated Products 1
9-2632; Rev ; /2 4.5Ω Dual SPST Analog Switches in UCSP General Description The MAX472/MAX4722/ low-voltage, low onresistance (R ON ), dual single-pole/single throw (SPST) analog switches operate from
More information0.8Ω, Low-Voltage, 4-Channel Analog Multiplexer
General Description The is a low on-resistance, low-voltage, 4-channel CMOS analog multiplexer that operates from a single 1.6V to 3.6V supply. This device has fast switching speeds (t ON = 25ns, t OFF
More informationMAX4751/MAX4752/MAX Ω, Low-Voltage, Single-Supply Quad SPST Analog Switches
// General Description The // are low on-resistance, low-voltage, quad, single-pole/single-throw (SPST) analog switches that operate from a single +1.V to +3.V supply. These devices have fast switching
More informationMAX4852 MAX4852H NC1 COM1 NO1 IN1 IN2 NC2 COM2 NO2. Maxim Integrated Products 1
19-7; Rev ; 7/ Dual SPDT Analog Switches with General Description The MAX8/MAX8H/MAX8/MAX8H family of dual SPDT (single-pole/double-throw) switches operate from a single +V to +.V supply and can handle
More informationEVALUATION KIT AVAILABLE 5.0Gbps PCI Express Passive Switches
19-77; Rev 2; 5/9 EVALUATION KIT AVAILABLE 5.Gbps PCI Express Passive Switches General Description The high-speed passive switches route PCI Express (PCIe) data between two possible destinations. The MAX4888A
More information5Ω, Quad, SPST, CMOS Analog Switches
9-393; Rev ; 8/99 5Ω, Quad, SPST, CMOS Analog Switches General Description The quad analog switches feature 5Ω max on-resistance. On-resistance is matched between switches to.5ω max and is flat (.5Ω max)
More informationS 500µA (typ) Supply Current S TSSOP 16-Pin Package S -40 C to +85 C Ambient Temperature Range S Functionally Compatible to DG411, DG412, and DG413
19-572; Rev ; 12/1 Quad SPST +7V Analog Switches General Description The are analog switches with a low on-resistance of 1I (max) that conduct equally well in both directions. All devices have a rail-to-rail
More informationUSB 2.0 Hi-Speed and Audio Switches with Negative Signal Capability
19-4136; Rev 1; 3/09 USB 2.0 Hi-Speed and Audio Switches General Description The high-esdprotected DPDT switches multiplex Hi-Speed (480Mbps) USB and analog signals such as AC-coupled audio or video. These
More informationMAX4661CWE. Pin Configurations/Functional Diagrams/Truth Tables IN2 NC2 V- NO2 MAX4662 NO3 COM3 IN3 SSOP/SO/DIP MAX4662 LOGIC SWITCH OFF
9-56; Rev ; 7/99 General Description The // quad analog switches feature low on-resistance of 2.5Ω max. On-resistance is matched between switches to.5ω max and is flat (.5Ω max) over the specified signal
More informationMAX4601CWE. Pin Configurations/Functional Diagrams/Truth Tables IN2 NO2 MAX4602 NO3 COM3 IN3 SSOP/SO/DIP MAX4602 LOGIC SWITCH OFF
9-396; Rev ; /99 2.5Ω, Quad, SPST, General Description The MAX46/MAX462/MAX463 quad analog switches feature low on-resistance of 2.5Ω max. On-resistance is matched between switches to.5ω max and is flat
More informationHigh-Speed, Low-Voltage, 4Ω, Dual SPST CMOS Analog Switches
9-; Rev ; / High-Speed, Low-oltage, Ω, Dual SPST General Description The MAX//MAX are monolithic, dual, single-pole/single-throw (SPST) switches that can operate from a single supply ranging from +. to
More informationMAX4737/MAX4738/ MAX Ω Quad SPST Analog Switches in UCSP. General Description. Benefits and Features. Applications
General Description The MAX77/MAX78/ low-voltage, low onresistance (R ), quad single-pole/single throw (SPST) analog switches operate from a single +.8V to +5.5V supply. These devices are designed for
More informationUltra-Small, Low-RON, Beyond-the-Rails DPDT Analog Switches
EVALUATION KIT AVAILABLE MAX14689 General Description The MAX14689 ultra-small, low-on-resistance (R ON ) double-pole/double-throw (DPDT) analog switches feature Beyond-the-Rails capability that allows
More informationHigh-Bandwidth T1/E1 Dual-SPDT Switches/ 4:1 Muxes
19-3915; Rev 1; 1/7 High-Bandwidth Dual-SPDT Switches/ General Description The / high-bandwidth, low-on-resistance analog dual SPDT switches/4:1 multiplexers are designed to serve as integrated protection
More informationMAX4734 LOGIC NO1 GND. Maxim Integrated Products 1
9-238; Rev ; 5/4.8Ω, Low-Voltage, 4-Channel General Description The is a low on-resistance, low-voltage, 4- channel CMOS analog multiplexer that operates from a single.6v to 3.6V supply. This device has
More information0.5Ω, Low-Voltage, Single-Supply SPST Analog Switches MAX4626/MAX4627/ MAX4628. General Description. Benefits and Features. Ordering Information
.5Ω, Low-Voltage, Single-Supply General Description The // are low-on-resistance, low-voltage, single-pole/single-throw (SPST) analog switches that operate from a +.8V to +5.5V single supply. The is normally
More informationMAX14777 Quad Beyond-the-Rails -15V to +35V Analog Switch
General Description The quad SPST switch supports analog signals above and below the rails with a single 3.0V to 5.5V supply. The device features a selectable -15V/+35V or -15V/+15V analog signal range
More informationMaxim Integrated Products 1
9-362; Rev 3; 6/7 Quad, SPST Analog Switch General Description The quad analog switch features on-resistance matching (4Ω max) between switches and guarantees on-resistance flatness over the signal range
More informationPART MAX4631ESE MAX4633CPE MAX4632EPE MAX4633MJE MAX4632CSE MAX4632CPE MAX4632ESE MAX4632MJE MAX4633CSE MAX4633ESE MAX4633EPE
19-1515; Rev ; 7/99 Fault-Protected, High-oltage, General Description The high-voltage, dual analog switches are pin compatible with the industry-standard DG41/DG43/DG45. They upgrade the existing devices
More informationQuad, Rail-to-Rail, Fault-Protected, SPDT Analog Switch
19-1452; Rev 1; 1/99 Quad, Rail-to-Rail, Fault-Protected, General Description The quad, single-pole/double-throw (SPDT), fault-protected analog switch is pin-compatible with the industry-standard MAX333
More informationQuad, Rail-to-Rail, Fault-Protected, SPDT Analog Switch
19-1452; Rev 1; 1/99 Quad, Rail-to-Rail, Fault-Protected, General Description The quad, single-pole/double-throw (SPDT), fault-protected analog switch is pin-compatible with the industry-standard MAX333
More informationPrecision, 8-Channel/Dual 4-Channel, Low-Voltage, CMOS Analog Multiplexers
9-299; Rev. 6; 6/7 Precision, 8-Channel/Dual 4-Channel, General Description The precision, monolithic, CMOS analog multiplexers (muxes) offer low on-resistance (less than Ω), which is matched to within
More informationLow-Charge Injection, 16-Channel, High-Voltage Analog Switches MAX14800 MAX14803
19-4484; Rev 1; 9/09 Low-Charge Injection, 16-Channel, General Description The provide high-voltage switching on 16 channels for ultrasonic imaging and printer applications. The devices utilize HVCMOS
More informationPI5A4684. Chip Scale Packaging, Dual SPDT Analog Switch. Features. Description. Pin Configuration/ Block Diagram (top view) CSP.
Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.5Ω. Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. High Off Isolation:
More informationPART MAX4887ETE +5V R0 G0 B0 R1 G1 B1 MAX4887 R2 G2 B2 SEL EN QP GND. Maxim Integrated Products 1
19-3972; Rev ; 2/6 Triple Video Switch General Description The triple, high-frequency switch is intended for notebooks and monitors to permit RGB signals to be switched from one driver to one of two loads
More informationMP2735/MP2736 Low-Voltage 0.45Ω Dual SPDT Analog Switches
The Future of Analog IC Technology GENERAL DESCRIPTION The MP2735/MP2736 are low voltage, low onresistance, dual single-pole, double-throw (SPDT) monolithic CMOS analog switches designed for high performance
More informationMAX14585/MAX14585A Hi-Speed USB and Audio Switches with Negative Signal Capability and High-Voltage-Tolerable VBUS Detection
19-5878; Rev ; 5/11 E V A L U A T I O N K I T A V A I L A B L E /A General Description The /A high-esd-protected doublepole/double-throw (DPDT) switches multiplex Hi-Speed (48Mbps) USB and analog signals
More information0.39, Low-R ON, Ultra-Low Distortion, Compact DPDT Analog Switch
.39, Low-R ON, Ultra-Low Distortion, Compact DPDT Analog Switch DESCRIPTION The is a compact, low resistance, ultra-low distortion double pole double throw (DPST) analog switch. The features a flat.39
More informationSGM4684 Chip Scale Packaging, Low-Voltage 0.4Ω, Dual, SPDT Analog Switch
GENERAL DESCRIPTION The SGM4684 is a dual, low on-resistance, low voltage, bidirectional, single-pole/double-throw (SPDT) CMOS analog switch designed to operate from a single 1.8V to 5.5V power supply.
More informationPI5A100. Precision, Wide-Bandwidth Quad SPDT Analog Switch. Description. Features. Block Diagram, Pin Configuration. Applications.
Precision, Wide-Bandwidth Quad SPDT Analog Switch Features Single Supply Operation (+2V to +6V) Rail-to-Rail Analog Signal Dynamic Range Low On-Resistance (6Ω typ with 5V supply) Minimizes Distortion and
More informationHi-Speed USB 2.0 Switches with ±15kV ESD MAX4983E/MAX4984E. Features
9-435; Rev 2; 9/8 EVALUATION KIT AVAILABLE Hi-Speed USB 2. Switches General Description The are high ESD-protected analog switches that combine the low on-capacitance and low on-resistance necessary for
More informationThe UM4684 is a sub 1Ω (0.5Ω at 2.7V) dual SPDT analog switch designed for low voltage
General Description 0.5Ω Low-Voltage Dual SPDT Analog Switch H CSP10 2.0 1.5 EEUE MSOP10 The is a sub 1Ω (0.5Ω at 2.7V) dual SPDT analog switch designed for low voltage applications. The has on-resistance
More informationPART MAX4584EUB MAX4585EUB TOP VIEW
19-1521; Rev ; 8/99 General Description The serial-interface, programmable switches are ideal for multimedia applicatio. Each device contai one normally open (NO) single-pole/ single-throw (SPST) switch
More informationLow-Voltage Single SPDT Analog Switch
Low-Voltage Single SPDT Analog Switch DG22 DESCRIPTION The DG22 is a single-pole/double-throw monolithic CMOS analog switch designed for high performance switching of analog signals. Combining low power,
More informationLow-Jitter, 8kHz Reference Clock Synthesizer Outputs MHz
19-3530; Rev 0; 1/05 Low-Jitter, 8kHz Reference General Description The low-cost, high-performance clock synthesizer with an 8kHz input reference clock provides six buffered LVTTL clock outputs at 35.328MHz.
More information2.5V Video Amplifier with Reconstruction Filter
19-3674; Rev ; 5/5 2.5V Video Amplifier with Reconstruction Filter General Description The small, low-power video amplifier with integrated reconstruction filter operates from a supply voltage as low as
More informationDG2535/DG Ω Low-Voltage Dual SPDT Analog Switch. Vishay Siliconix. RoHS COMPLIANT DESCRIPTION FEATURES BENEFITS APPLICATIONS
0.35-Ω Low-Voltage Dual SPDT Analog Switch DG2535/DG2536 DESCRIPTION The DG2535/DG2536 is a sub Ω (0.35 Ω at 2.7 V) dual SPDT analog switches designed for low voltage applications. The DG2535/DG2536 has
More informationShunt Mode Audio Click-and-Pop Eliminator
19-4295; Rev ; 1/8 Shunt Mode udio Click-and-Pop Eliminator General Description The is an audio click-and-pop eliminator for portable multimedia devices. Operating from a 1.7V to 3.6V supply, the connects
More information*EP = exposed pad TOP VIEW COM N.C. GND. Maxim Integrated Products 1
9-984; Rev ; 5/ High-urrent, Ω, SPST, MOS General Description Maxim s are medium-voltage MOS analog switches with low on-resistance of Ω max, specifically designed to handle large switch currents. With
More information0.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854
.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854 FEATURES.8 Ω typical on resistance Less than 1 Ω maximum on resistance at 85 C 1.8 V to 5.5 V single supply High current carrying capability:
More informationBCT4699ETE. Applications. Ordering Information. December, 2013, REV1.1
BCT4699 General Description The BCT4699 is configured as a quad-spdt switch with two common control inputs. Each digital input controls two pairs of SPDT switches. The switches are fully bi-directional,
More informationLow-Voltage, Low R ON, SPDT Audio Switch with Negative Swing Capability
Low-Voltage, Low R ON, SPDT Audio Switch with Negative Swing Capability DG6, DG63 DESCRIPTION The DG6, DG63 is a low on-resistance, single-pole/ double-throw monolithic CMOS analog switch with negative
More information16-Channel CMOS Analog Multiplexer. Memory
306 16-Channel CMOS Analog Multiplexer FEATURES: RAD-PAK technology radiation-hardened against natural space radiation Total dose hardness: - > 50 Krad (Si), depending upon space mission Excellent Single
More informationUM Ω Ultra Low ON-Resistance Dual SPDT Analog Switch UM5223 QFN General Description. Applications
0.5Ω Ultra Low ON-Resistance Dual SPDT Analog Switch UM5223 QFN10 1.8 1.4 General Description The UM5223 is a low on-resistance (R ON ), dual single-pole/double-throw (SPDT) analog switch operates from
More informationRail-to-Rail, 200kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP
19-579; Rev ; 12/1 EVALUATION KIT AVAILABLE Rail-to-Rail, 2kHz Op Amp General Description The op amp features a maximized ratio of gain bandwidth (GBW) to supply current and is ideal for battery-powered
More informationFeatures. Applications
DATASHEET IDTHS221P10 Description The IDTHS221P10 is a high-performance hybrid switch device, combined with hybrid low distortion audio and USB 2.0 high speed data (480 Mbps) signal switches, and analog
More informationDual, Audio, Log Taper Digital Potentiometers
19-2049; Rev 3; 1/05 Dual, Audio, Log Taper Digital Potentiometers General Description The dual, logarithmic taper digital potentiometers, with 32-tap points each, replace mechanical potentiometers in
More informationQuad SPST CMOS Analog Switches
9-3960; Rev 3; 6/06 Quad SPST CMOS Analog Switches General Description The are normally open, quad singlepole single-throw (SPST) analog switches. These CMOS switches can be continuously operated with
More informationSGM3003 Ultra Low ON-Resistance, Low Voltage, SPDT Analog Switch
GENERAL DESCRIPTION The SGM3003 is a single, low on-resistance, low voltage, bidirectional, single-pole/double-throw (SPDT) CMOS analog switch designed to operate from a single +1.8V to +5.5V supply. Targeted
More informationSub-Ω, Low Voltage, SPDT Analog Switches with Over Current Protection
New Product DG/DG1 Sub-Ω, Low Voltage, SPDT Analog Switches with Over Current Protection DESCRIPTION The DG/DG1 are low-voltage single single-pole/ double-throw monolithic CMOS analog switches. Designed
More informationLow-Voltage Single-Supply, SPDT Analog Switch in SC-70
Low-oltage Single-Supply, SPDT Analog Switch in SC-7 DESCRIPTION The DG499 is a cost effective upgrade to other types of 499 low-voltage, single-pole/double-throw analog switches available in the industry
More informationFEATURES BENEFITS APPLICATIONS. PARAMETER LIMIT UNIT Reference to GND V to +6 IN, COM, NC, NO a -0.3 to (V )
DESCRIPTION www.vishay.com.5, High Bandwidth, Dual SPDT Analog Switch The DGE is a low-voltage dual single-pole / double-throw monolithic CMOS analog switch. Designed to operate from. V to 5.5 V power
More informationLow-Voltage, 1.8kHz PWM Output Temperature Sensors
19-266; Rev 1; 1/3 Low-Voltage, 1.8kHz PWM Output Temperature General Description The are high-accuracy, low-power temperature sensors with a single-wire output. The convert the ambient temperature into
More information140ms (min) WDO Pulse Period PART. Maxim Integrated Products 1
19-2804; Rev 2; 12/05 5-Pin Watchdog Timer Circuit General Description The is a low-power watchdog circuit in a tiny 5- pin SC70 package. This device improves system reliability by monitoring the system
More information0.4, Low Resistance and Capacitance, Dual DPDT / Quad SPDT Analog Switch
.4, Low Resistance and Capacitance, Dual DPDT / Quad SPDT Analog Switch DESCRIPTION The DG2523 and DG2524 are four-channel single-pole double-throw (SPDT) analog switches. The DG2523 has two control inputs
More informationSGM48754 Quad SPST CMOS Analog Switch
GENERAL DESCRIPTION The is a CMOS analog switch configured as quad SPST. This CMOS device can operate from 2.5V to 5.5V single supplies. Each switch can handle rail-to-rail analog signals. The off-leakage
More informationDual DPDT Ultra-Low R ON
General Description Dual DPDT Ultra-Low R ON Analog Switch UM3699A UM3699A QFN16 3.0 3.0 The UM3699A are dual independent ultra low R ON DPDT analog switches. These devices are designed for low operating
More informationHigh-Voltage Switch for Wireless Power
General Description The MAX20304 is a DPST switch intended for wirelesspower-circuit applications. The new application for the portable device is the magnetic card reader. There has been a method to use
More informationSGM Ω Ultra Low ON-Resistance, Dual, SPDT Analog Switch
GENERAL DESCRIPTION The SGM2267 is a dual single-pole/double-throw (SPDT) analog switch that is designed to operate from a single +1.8V to +4.2V power supply. Targeted applications include battery powered
More informationMAX9812/MAX9813 Tiny, Low-Cost, Single/Dual-Input, Fixed-Gain Microphone Amplifiers with Integrated Bias
General Description The MAX982/MAX983 are single/dual-input, 20dB fixed-gain microphone amplifiers. They offer tiny packaging and a low-noise, integrated microphone bias, making them ideal for portable
More informationPower-off Isolation, 6, 1.8 V to 5.5 V, SPDT Analog Switch (2:1 Multiplexer)
Power-off Isolation,,. V to 5.5 V, SPDT Analog Switch (: Multiplexer) DESCRIPTION The is a high performance single-pole, double-throw (SPDT) analog switch designed for. V to 5.5 V operation with a single
More informationLow-Cost, Micropower, High-Side Current-Sense Amplifier + Comparator + Reference ICs
9-63; Rev ; /3 Low-Cost, Micropower, High-Side Current-Sense General Description The low-cost, micropower, high-side current-sense supervisors contain a highside current-sense amplifier, bandgap reference,
More informationLVDS or LVTTL/LVCMOS Input to 14 LVTTL/LVCMOS Output Clock Driver
19-2392; Rev ; 4/2 LVDS or LVTTL/LVCMOS Input to General Description The 125MHz, 14-port LVTTL/LVCMOS clock driver repeats the selected LVDS or LVTTL/LVCMOS input on two output banks. Each bank consists
More informationPrecision, Low-Power, 6-Pin SOT23 Temperature Sensors and Voltage References
19-2457; Rev 2; 11/03 Precision, Low-Power, 6-Pin SOT23 General Description The are precise, low-power analog temperature sensors combined with a precision voltage reference. They are ideal for applications
More informationSGM3717 4Ω, 400MHz Bandwidth, Dual, SPDT Negative Signal Handling Analog Switch
Preliminary datasheet SGM3717 GENERAL DESCRIPTION The SGM3717 is a dual, bidirectional, single-pole/ double-throw (SPDT) CMOS analog switch designed to operate from a single +2.5V to +5.0V supply. It features
More informationAS11P2TLR. Low voltage 1 Ω single-pole double-throw analog switch with breakbefore-make. Description. Features
Low voltage 1 Ω single-pole double-throw analog switch with breakbefore-make feature Description Datasheet - production data Features DFN6L High speed: t PD = 130 ps (typ.) at V CC = 3.0 V t PD = 140 ps
More information500mA Low-Dropout Linear Regulator in UCSP
19-272; Rev ; 1/2 5mA Low-Dropout Linear Regulator in UCSP General Description The low-dropout linear regulator operates from a 2.5V to 5.5V supply and delivers a guaranteed 5mA load current with low 12mV
More information0.4 Ω CMOS, Dual DPDT Switch in WLCSP/LFCSP/TSSOP ADG888
FEATURES.8 V to 5.5 V operation Ultralow on resistance.4 Ω typical.6 Ω maximum at 5 V supply Excellent audio performance, ultralow distortion.7 Ω typical.4 Ω maximum RON flatness High current carrying
More information0.45, Low Voltage Dual SPDT Analog Switch with Negative Swing Audio Capability
5, Low Voltage Dual SPDT Analog Switch with Negative Swing Audio Capability DESCRIPTION The is a dual SPDT low on-resistance switch designed to from a single 1.6 V to 5.5 V power supply. It is a bi-directional
More informationSGM Ω, High Speed, Low Voltage Dual, DPDT Analog Switch
GENERAL DESCRIPTION The SGM44601 is a high-speed, low-voltage, advanced dual-independent double-pole/double-throw (DPDT) CMOS analog switch that is designed to operate from a single +1.8V to +5.5V power
More informationIF Digitally Controlled Variable-Gain Amplifier
19-2601; Rev 1; 2/04 IF Digitally Controlled Variable-Gain Amplifier General Description The high-performance, digitally controlled variable-gain amplifier is designed for use from 0MHz to 400MHz. The
More informationOvervoltage-Protection Controllers with Status FLAG
19-3979; Rev 0; 2/06 Overvoltage-Protection Controllers with Status General Description The // are overvoltageprotection ICs that protect low-voltage systems against voltages of up to +28V. If the input
More informationPrecision, 4-Channel/Dual 2-Channel, Low-Voltage, CMOS Analog Multiplexers
9-7; Rev. ; /98 Precision, 4-Channel/Dual 2-Channel, General Description The AX48/AX49 precision, monolithic, COS analog multiplexers (muxes) offer low on-resistance (less than ), which is matched to within
More informationPower-off Protection, 6, 1.8 V to 5.5 V, SPDT Analog Switch (2:1 Multiplexer)
Power-off Protection,,. V to 5.5 V, SPDT Analog Switch (: Multiplexer) DESCRIPTION The is a high performance single-pole, double-throw (SPDT) analog switch designed for. V to 5.5 V operation with a single
More information