Engineering Innovation Center Autodesk Fusion 360
|
|
- Meredith Wilson
- 6 years ago
- Views:
Transcription
1 Engineering Innovation Center Autodesk Fusion 360
2 Introduction The Engineering Innovation Center is a large academic maker space with plenty of tools and equipment. In order to use these items you must have the proper training. This online popup class will teach the basic fundamentals of this tool or piece of equipment. Fusion 360 This class will teach the basics of modeling in fusion 360 and how take these files and submit them for prototyping. The key is the right tool for the right job. This class will discuss how to identify and use these tools. 1/22/2017 Engineering Innovation Center 2
3 How to get Fusion 360 The Fusion 360 program is a free download for students from the Autodesk website. To get the program go to 360/students-teachers-educators?td=aexfusio From here you can sign in or create an account so that you can get the software. Once you are signed into your account you will see a download now button. 1/22/2017 Engineering Innovation Center 3
4 How to get Fusion 360 (cont.) Once your download is complete click it and run it. This will cause fusion 360 to start downloading. Once the program is done downloading you will be asked to sign in to your Autodesk account. Once you have signed in then your are ready to start using Fusion 360 1/22/2017 Engineering Innovation Center 4
5 Overview Navigation of software Creation of part Defined sketches Extrusions Features Drawing Dimensioning Section views Feature callouts How to submit for Prototyping 1/22/2017 Engineering Innovation Center 5
6 Navigation of Software Start up Fusion 360 Sign into your Autodesk account Once your are signed in you should be able to see the working area in fusion. You can start working in this immediately or open up a file from the 360 cloud where you have saved any previous work. 1/22/2017 Engineering Innovation Center 6
7 Navigation of software This is where files show up when they are saved. This is where components of your model will be if you need to edit them later This is the main toolbar where most functions are found This toolbar allows you to change your view of an object This is the main modeling area This allows for different views of object 1/22/2017 Engineering Innovation Center 7
8 Sketches These are the basis for any part These should always be fully defined You can use relations/constraints to help define sketch geometry 1/22/2017 Engineering Innovation Center 8
9 Create a Sketch Use the start sketch button To do this click the sketch drop down menu and it will be the first option Pick a plane for your sketch 1/22/2017 Engineering Innovation Center 9
10 Your sketching area should look something like this now Using the sketching drop down menu you can access several different way to draw on this surface from simple lines, to rectangles and circles, to polygons and arcs. Using these functions replicate the picture on the lower right. 1/22/2017 Engineering Innovation Center 10
11 Dimension/Constrain These help to define a sketch To dimension use the sketch dimension tool in the sketch drop down menu To constrain an object use the menu that appears to the right of the sketch when you are in the sketching mode When you are finished with your sketch click the stop sketch button at the bottom of this menu 1/22/2017 Engineering Innovation Center 11
12 Extrusion Extrusions make your 2d sketch into a 3d model To do an extrusion click the extrude command. You now need to click your sketch, it will turn blue and have a small window that defines how much the piece should be extruded. 1/22/2017 Engineering Innovation Center 12
13 Adding features You can add new features to your modeling by using commands such as the hole command or by making a new sketch on a surface and using extrusion. To use the hole feature click on the create drop down menu and the hole command will be in there. You then click on the surface you want to put the hole onto. Once this is done a menu will appear that will allow to adjust the aspects of the hole To center the hole click select on the references then click on the long edge and enter half of your objects width Once you are done with the hole you can click ok. 1/22/2017 Engineering Innovation Center 13
14 Creating an extrusion from a surface To create a extrusion that starts from a surface use the same method of starting a sketch but choose the surface as your plane You then follow the same steps as doing this in a normal plane Try to add the extrusion shown to the right to your part. (The circle feature is found in the sketch drop down menu and you can use the concentric constraint to match it up with the outer circle edge.) 1/22/2017 Engineering Innovation Center 14
15 Adding Features (cont.) Many features can be found in the modify drop down menu These features include things such as chamfer and fillets, along with things like shell The fillet feature will add a round edge to corners and edges The chamfer feature will create a flat angle along edges The shell feature will hallow out the part creating a part that uses less material 1/22/2017 Engineering Innovation Center 15
16 Fillet To add a fillet to a piece select the fillet command from the modify menu. Then click on the edges you want to fillet You can adjust the fillet using the pop up menu that appears Try to create a fillet along the outer edge of the main body. 1/22/2017 Engineering Innovation Center 16
17 Chamfer To add a chamfer to a piece select the chamfer command from the modify menu. Then click on the edges you want to chamfer You can adjust the chamfer using the pop up menu that appears Try to create a chamfer around the extruded cylinder and the outer edge of the hole 1/22/2017 Engineering Innovation Center 17
18 Shell To add a shell to a piece select the shell command from the modify menu. Then click on the surface you want to shell You can adjust the shell using the pop up menu that appears Try to create a shell on the bottom surface of the body You can get to the bottom surface by clicking on the bottom surface on the cube in the top right hand corner 1/22/2017 Engineering Innovation Center 18
19 Finished Model 1/22/2017 Engineering Innovation Center 19
20 Drawings Drawings allow you to communicate the features of your model to: The public Machinists Investors Anyone After creating your model select the file button then click the new drawing from design button the then new drawing menu You will then get a menu to create the new drawing set it up like the one to the right 1/22/2017 Engineering Innovation Center 20
21 Drawings (cont.) Once you have done this you will be on the drawing sheet and need to place the base view You will then need to create the projected views by clicking on the projected views button in the drawing views menu Once you do this click on your base view and then click to the right, top, and bottom of the base view to generate the other views. 1/22/2017 Engineering Innovation Center 21
22 Drawing (cont.) Once you have all of your views you must fully dimension your part To do this click the dimension button on the top bar When dimensioning follow the following guidelines Avoid crossing lines Include all needed dimensions Place dimensions between the view Always do drawings in inches 1/22/2017 Engineering Innovation Center 22
23 Title block To access the title block your double click on the box and it will bring up a menu for you to edit the box You must use a text box for the lower left hand box 1/22/2017 Engineering Innovation Center 23
24 Export as.stl To export for 3d printing you must export as a.stl file To do this you double click on your object so that it is highlighted in light blue. You then right click and select save as stl your then will be given a menu that allows you to change a few things such as refinement which is needed when the part has many circular features. Then click ok and save it onto a flash drive that you can bring up to the eic. 1/22/2017 Engineering Innovation Center 24
Autodesk Inventor 2016 Creating Sketches
Autodesk Inventor 2016 Creating Sketches 2D Sketch Practice 1 1. Launch Autodesk Inventor 2016 2. Create a new Part file (.ipt) 3. Save File As a. Click on the save icon. b. Save you file onto your flash
More informationIntroduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software
Introduction to 3D Printing Activity 1: Design a keychain using computer-aided design software 1 In this activity we ll design a keychain name tag and learn the fundamentals of computer-aided design, the
More informationEngineering Innovation Center Fabrication Shop Basic CAD Training
Engineering Innovation Center Fabrication Shop Basic CAD Training Introduction The Engineering Innovation Center Fabrication Shop was established for support of undergraduate student course work. Every
More informationCube in a cube Fusion 360 tutorial
Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.
More informationIntroduction to Autodesk Inventor User Interface Student Manual MODEL WINDOW
Emmett Wemp EDTECH 503 Introduction to Autodesk Inventor User Interface Fill in the blanks of the different tools available in the user interface of Autodesk Inventor as your instructor discusses them.
More information1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry
2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply
More informationSolidWorks Navigation
SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length
More informationADA Curriculum for Pre-Engineering Students Correlation Guide
ADA Curriculum for Pre-Engineering Students Correlation Guide Madsen/Autodesk Inventor 7: Basics Through Advanced Note: The concepts presented in the ADA Curriculum are covered in the text as they pertain
More informationLesson 6 2D Sketch Panel Tools
Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,
More informationObjectives. Inventor Part Modeling MA 23-1 Presented by Tom Short, P.E. Munro & Associates, Inc
Objectives Inventor Part Modeling MA 23-1 Presented by Tom Short, P.E. Munro & Associates, Inc To demonstrate most of the sketch tools and part features in : Inventor Release 6 And, to show logical techniques
More informationEngineering & Computer Graphics Workbook Using SolidWorks 2014
Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
More informationSolidWorks Design & Technology
SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one
More informationIntroduction to ANSYS DesignModeler
Lecture 4 Planes and Sketches 14. 5 Release Introduction to ANSYS DesignModeler 2012 ANSYS, Inc. November 20, 2012 1 Release 14.5 Preprocessing Workflow Geometry Creation OR Geometry Import Geometry Operations
More informationEngineering & Computer Graphics Workbook Using SOLIDWORKS
Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
More informationNut and Bolt Tutorial
Thread Representations Nut and Bolt Tutorial Parts to a Thread Thread Dimensioning Major Diameter Thread Series (IE UNC, UNF, ACME, etc) ½ - 13 UNC 2 A or B A = External B = Internal Threads per Inch Class
More informationIntroduction to solid modeling using Onshape
Onshape is a CAD/solid modeling application. It provides powerful parametric and direct modeling capabilities. It is cloud based therefore you do not need to install any software. Documents are shareable.
More informationME Week 2 Project 2 Flange Manifold Part
1 Project 2 - Flange Manifold Part 1.1 Instructions This project focuses on additional sketching methods and sketching commands. Revolve and Work features are also introduced. The part being modeled is
More informationActivity Sketch Plane Cube
Activity 1.5.4 Sketch Plane Cube Introduction Have you ever tried to explain to someone what you knew, and that person wanted you to tell him or her more? Here is your chance to do just that. You have
More informationIntroduction to 3D CAD with SolidWorks. Jianan Li
Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,
More informationVan Assembly. Creating an Assembly. Original by Steven Jaffe Modified by E. Brunelle 2/07 1
Van Assembly Creating an Assembly 1 Part One the Axle 1. Set Units to Inches 2. Create a New Design. 3. Save the Design as axleinl_cad1_1 in your Van folder. 4. Create a New Sketch on the Lateral workplane.
More informationFrom the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select
Chapter 5 In sweep command there is a) Two sketch profiles b) Two path c) One sketch profile and one path The sweep profile is used to create threads springs circular things and difficult geometry. For
More informationAutodesk Fusion 360 Introduction to Parametric Modeling
Autodesk Fusion 360 Introduction to Parametric Modeling Course Length: 5 days The Autodesk Fusion 360 Introduction to Parametric Modeling training course provides you with an understanding of the parametric
More informationUsing Siemens NX 11 Software. The connecting rod
Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open
More informationDiane Burton, STEM Outreach.
123D Design Tutorial: LED decoration Before using these instructions, it is very helpful to watch this video screencast of the CAD drawing actually being done in the software. Click this link for the video
More informationFeature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05
Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating
More information10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B
Chevy Malibu Vehicle Design with Solidworks Start SolidWorks Create a New SolidWorks Document Miles, Rowardo B 1 Click: Part and then OK Now you are ready to make a Part. 2 Right Toolbar: Document Properties:
More informationInventor-Parts-Tutorial By: Dor Ashur
Inventor-Parts-Tutorial By: Dor Ashur For Assignment: http://www.maelabs.ucsd.edu/mae3/assignments/cad/inventor_parts.pdf Open Autodesk Inventor: Start-> All Programs -> Autodesk -> Autodesk Inventor 2010
More informationEXERCISE ONE: BEACH BUGGY.
EXERCISE ONE: BEACH BUGGY. Prerequisite knowledge Students should have completed Exercises from the file: Introduction to Assemblies Concept Mates Focus of lesson Commands Used This lesson will focus on
More informationDigital Camera Exercise
Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document
More informationIntroduction to Autodesk Inventor for F1 in Schools (Australian Version)
Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital
More information1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry
4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are
More informationName: Date Completed: Basic Inventor Skills I
Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.
More informationJ. La Favre Fusion 360 Lesson 2 April 19, 2017
In this lesson, you will create a round plate with 12 counter-bored holes to fit 6-32 socket head screws. A counter-bored hole has two diameters, one to fit the threaded part of the screw and the other
More informationLab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008
1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical
More informationIntroduction to Circular Pattern Flower Pot
Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,
More informationAEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.
AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and
More informationSolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
More informationNX 7.5. Table of Contents. Lesson 3 More Features
NX 7.5 Lesson 3 More Features Pre-reqs/Technical Skills Basic computer use Completion of NX 7.5 Lessons 1&2 Expectations Read lesson material Implement steps in software while reading through lesson material
More informationIntroduction to Revolve - A Glass
Introduction to Revolve - A Glass Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Prerequisite Knowledge Previous knowledge of the following commands are required
More informationTable of Contents. Lesson 1 Getting Started
NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard
More informationDatum Tutorial Part: Cutter
Datum Tutorial Part: Cutter Objective: Learn to apply Datums in different ways Directions 1. Datum Axis Creation a. First we need to create a center axis for the cutter b. Model Tab > Datum > Select Axis
More informationConquering the Rubicon
Autodesk Inventor R10 Fundamentals: Conquering the Rubicon Elise Moss SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Schroff Development Corporation P.O. Box 1334
More information1. Change units to inches: Tools > Options > Document Properties > Units and then select: IPS (inch, pound, second)
Steps to Draw Pump Impeller: The steps below show one way to draw the impeller. You should make sure that your impeller is not larger than the one shown or it may not fit in the pump housing. 1. Change
More informationPro/DESKTOP Tutorial Drafting Bow Compass
Pro/DESKTOP Tutorial Drafting Bow Compass Michael Flowers 2005 1 Objectives: To develop confidence with the Pro/DESKTOP software. To learn to utilize extrude, project, revolve, round, and chamfer features.
More informationEngineering Technology
Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,
More informationPart Design. Sketcher - Basic 1 13,0600,1488,1586(SP6)
Part Design Sketcher - Basic 1 13,0600,1488,1586(SP6) In this exercise, we will learn the foundation of the Sketcher and its basic functions. The Sketcher is a tool used to create two-dimensional (2D)
More informationIntroduction to CATIA V5
Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower
More informationSiemens NX11 tutorials. The angled part
Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure
More informationSolidworks Tutorial Pencil
The following instructions will be used to help you create a Pencil using Solidworks. These instructions are ordered to make the process as simple as possible. Deviating from the order, or not following
More informationWhen you complete this assignment you will:
Objjectiives When you complete this assignment you will: 1. Set-up menus and drawing for designing modeling problems. 2. become familiar with the Sketch menu tools and commands. 3. Produce a three-dimensional
More informationDrawing and Assembling
Youth Explore Trades Skills Description In this activity the six sides of a die will be drawn and then assembled together. The intent is to understand how constraints are used to lock individual parts
More informationSolidworks: Lesson 4 Assembly Basics and Toolbox. UCF Engineering
Solidworks: Lesson 4 Assembly Basics and Toolbox UCF Engineering Solidworks We have now completed the basic features of part modeling and it is now time to begin constructing more complex models in the
More information< Then click on this icon on the vertical tool bar that pops up on the left side.
Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts
More informationQuick Start for Autodesk Inventor
Quick Start for Autodesk Inventor Autodesk Inventor Professional is a 3D mechanical design tool with powerful solid modeling capabilities and an intuitive interface. In this lesson, you use a typical workflow
More informationStraw support Fusion 360
Straw support Fusion 360 Before using these instructions, watch the video screencast of the CAD drawing actually being done in the software. Click this link for video tutorial This design works on a variety
More information2809 CAD TRAINING: Part 1 Sketching and Making 3D Parts. Contents
Contents Getting Started... 2 Lesson 1:... 3 Lesson 2:... 13 Lesson 3:... 19 Lesson 4:... 23 Lesson 5:... 25 Final Project:... 28 Getting Started Get Autodesk Inventor Go to http://students.autodesk.com/
More informationFUSION 360: SKETCHING FOR MAKERS
FUSION 360: SKETCHING FOR MAKERS LaDeana Dockery 2017 MAKEICT Wichita, KS 1 Table of Contents Interface... 1 File Operations... 1 Opening Existing Models... 1 Mouse Navigation... 1 Preferences... 2 Navigation
More informationClock Exercise (Inserting Planes)
Clock Exercise (Inserting Planes) Prerequisite Knowledge To complete this exercise you will need to be familiar with Sketching, Applying relations, Extrude Boss/ Base, Extrude cut, Applying Textures, Renaming
More informationInventor 2016 Essentials Plus
Autodesk NEW Features a chapter on sheet metal design Inventor 2016 Essentials Plus Daniel T. Banach & Travis Jones SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF
More informationShaft Hanger - SolidWorks
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric
More informationAutodesk Inventor. In Engineering Design & Drafting. By Edward Locke
Autodesk Inventor In Engineering Design & Drafting By Edward Locke Engineering Design Drafting Essentials Working Drawings: Orthographic Projection Views (multi-view, auxiliary view, details and sections)
More informationModule 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece
1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a
More informationSTEP BY STEP GUIDE FOR CREATING A CUBE IN FREECAD. STEP 1. Chose Create a new Empty Document Part Design Create a New Sketch XY- Plane and click OK.
STEP BY STEP GUIDE FOR CREATING A CUBE IN FREECAD STEP 1. Chose Create a new Empty Document Part Design Create a New Sketch XY- Plane and click OK. STEP 2. Chose Rectangle tool and create any rectangle
More informationPart 8: The Front Cover
Part 8: The Front Cover 4 Earpiece cuts and housing Lens cut and housing Microphone cut and housing The front cover is similar to the back cover in that it is a shelled protrusion with screw posts extruding
More informationSolidWorks 95 User s Guide
SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents
More informationBasic Features. In this lesson you will learn how to create basic CATIA features. Lesson Contents: CATIA V5 Fundamentals- Lesson 3: Basic Features
Basic Features In this lesson you will learn how to create basic CATIA features. Lesson Contents: Case Study: Basic Features Design Intent Stages in the Process Determine a Suitable Base Feature Create
More informationModule 2.1, 2.2 Review. EF101 Analysis & Skills Module 2.3. Sketched Features and Operations. On-line Help Two Locations
EF101 Analysis & Skills Module 2.3 Engineering Graphics Revolved Features Placed Features Work Features Module 2.1, 2.2 Review What are the three types of operations for adding features to the base feature?
More information1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define.
BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Control + Click HERE to view enlarged IMAGE and Construction Strategy he following set of
More informationDEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY
DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY CAPSULE PROGRAM Funded by NSF grant #0833636 Tutorial 02 3D Part Modeling SolidWorks 2010 Copyright 2010 Prof. Zeid 3D Part Modeling
More informationIntroduction to Sheet Metal Features SolidWorks 2009
SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to
More informationBeginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS
Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling
More informationSolidWorks Training. Introductory course for staff and students from the School of Physics and Astronomy
SolidWorks Training Introductory course for staff and students from the School of Physics and Astronomy i) Introductory presentation SolidWorks Training ii) The SolidWorks GUI The SolidWorks Graphical
More informationR2-D2 SolidWorks Model
R2-D2 SolidWorks Model Mike Haftl E-Design 100 Section 7 August 5, 2016 Haftl 1 Rendered Images Figure 1: Front view of R2-D2 model made in solid works Figure 2: Isometric Left view of R2-D2 model made
More informationModeling Basic Mechanical Components #1 Tie-Wrap Clip
Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely
More informationActivity 5.5a CAD Model Features Part 1
Activity 5.5a CAD Model Features Part 1 Introduction In order to use CAD effectively as a design tool, the designer must have the skills necessary to create, edit, and manipulate a 3D model of a part in
More informationIntroducing SolidWorks
Introducing SolidWorks SAAST Robotics 2008 SolidWorks Software Visually-based 3-D Mechanical design software Engineers and Designers use it to: Quickly sketch out ideas Experiment with features, dimensions
More informationUNIT 11: Revolved and Extruded Shapes
UNIT 11: Revolved and Extruded Shapes In addition to basic geometric shapes and importing of three-dimensional STL files, SOLIDCast allows you to create three-dimensional shapes that are formed by revolving
More informationAlternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
More informationExplanation of buttons used for sketching in Unigraphics
Explanation of buttons used for sketching in Unigraphics Sketcher Tool Bar Finish Sketch is for exiting the Sketcher Task Environment. Sketch Name is the name of the current active sketch. You can also
More informationProduct Modelling in Solid Works
Product Modelling in Solid Works In the following exercise you will use solid works to construct the computer mouse shown opposite. In this exercise you will use a number of advanced features to achieve
More informationPart Design Fundamentals
Part Design Fundamentals 1 Course Presentation Objectives of the course In this course you will learn basic methods to create and modify solids features and parts Targeted audience New CATIA V5 Users 1
More informationHow to Build a Game Console. David Hunt, PE
How to Build a Game Console David Hunt, PE davidhunt@outdrs.net Covering: Drafts Fillets Shells Patterns o Linear o Circular Using made-for-the-purpose sketches to define reference geometry Using reference
More informationCreate A Mug. Skills Learned. Settings Sketching 3-D Features. Revolve Offset Plane Sweep Fillet Decal* Offset Arc
Create A Mug Skills Learned Settings Sketching 3-D Features Slice Line Tool Offset Arc Revolve Offset Plane Sweep Fillet Decal* Tutorial: Creating A Custom Mug There are somethings in this world that have
More informationWhen you complete this assignment you will:
Objjectiives When you complete this assignment you will: 1. sketch and dimension circles and arcs. 2. cut holes in the model using the cut feature of the extrusion command. 3. create Arcs using the trim
More informationCAD Tutorial 24: Step by Step Guide
CAD TUTORIAL 24: Step by step CAD Tutorial 24: Step by Step Guide Level of Difficulty Time Approximately 40 50 minutes Lesson Objectives To understand the basic tools used in SketchUp. To understand the
More informationChapter 2. Drawing Sketches for Solid Models. Learning Objectives
Chapter 2 Drawing Sketches for Solid Models Learning Objectives After completing this chapter, you will be able to: Start a new template file to draw sketches. Set up the sketching environment. Use various
More informationBottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
More information1.6.7 Add Arc Length Dimension Modify Dimension Value Check the Sketch Curve Connectivity
Contents 2D Sketch... 1 1.1 2D Sketch Introduction... 1 1.1.1 2D Sketch... 1 1.1.2 Basic Setting of 2D Sketch... 2 1.1.3 Exit 2D Sketch... 4 1.2 Draw Common Geometry... 5 2.2.1 Points... 5 2.2.2 Lines
More informationSolidWorks & Tinkerine 3D Printing Tutorial ELEC391
SolidWorks & Tinkerine 3D Printing Tutorial ELEC391 Engineering Services, Dept. of Electrical and Computer Engineering University of British Columbia, Faculty of Applied Science Table of Contents Installing
More informationSolid Part Four A Bracket Made by Mirroring
C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude
More informationModule 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder
Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic
More informationJ. La Favre Fusion 360 Lesson 4 April 21, 2017
In this lesson, you will create an I-beam like the one in the image to the left. As you become more experienced in using CAD software, you will learn that there is usually more than one way to make a 3-D
More informationLAB 1A: Intro to SolidWorks: 2D -> 3D Brackets
LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets Set units Create Sketch Add relations Linear patterns Mirror Fillet Extrude Extrude cut First, set units. click Option on top of main menu Open Document Properties
More informationThe project focuses on the design for a Pencil holder, but could be adapted to any simple assembly.
Introduction - Teacher Notes Fig 1. The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly. Pro/DESKTOP enables pupils (and teachers) to communicate and model
More informationAutodesk Inventor Introduction to Solid Modeling
Autodesk Inventor Introduction to Solid Modeling Course Length: 5 days The Autodesk Inventor Introduction to Solid Modeling training course provides you with an understanding of the parametric design philosophy
More informationChair. Bottom Rail. on the Command Manager. on the Weldments toolbar.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
More informationConstructing a Wedge Die
1-(800) 877-2745 www.ashlar-vellum.com Using Graphite TM Copyright 2008 Ashlar Incorporated. All rights reserved. C6CAWD0809. Ashlar-Vellum Graphite This exercise introduces the third dimension. Discover
More informationSolidWorks 103: Barge Design Challenge
SolidWorks 103: Barge Design Challenge Note: This tutorial was created using SolidWorks 2009. If you are using another version of SolidWorks, you may notice some variation in display states and configuration.
More informationModule 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge
Inventor (10) Module 1G: 1G- 1 Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge In Module 1A, we have explored
More information