Clock Exercise (Inserting Planes)

Size: px
Start display at page:

Download "Clock Exercise (Inserting Planes)"

Transcription

1 Clock Exercise (Inserting Planes) Prerequisite Knowledge To complete this exercise you will need to be familiar with Sketching, Applying relations, Extrude Boss/ Base, Extrude cut, Applying Textures, Renaming features. Focus of the Lesson On completion of this lesson you will have used: to insert a plane using: a line and a point 3 points a line and an angle Cut with Surface. Commands Used This lesson includes Sketching, Adding Relations, Extrude Boss/ Base, Renaming features, Inserting Planes, Renaming Planes, Extrude Cut, Cutting with planes, Applying Textures. Design & Communication Graphics 1

2 Getting Started Open a new part and save it as Clock Create a sketch on the top plane using the dimensions shown and adding equal relations. Position the sketch such that the origin is at the midpoint of the centerline. Select Extrude Boss/Base Choose the Blind option from the list and enter a Depth of 200mm. Rename the feature clock base. Inserting planes Includes planes, axes, coordinate systems, and 3D curves. Reference geometry can be used to create new planes for sketches or to create cut surfaces on solids. Planes can be created through lines and points, parallel to an existing plane or at a given angle. Where to find it Select from the features toolbar or from the Insert menu, select. Insert plane using Line and point To insert a diagonal plane Select Reference Geometry, Plane, select through lines and points option, select the edge and corner shown in green Click OK Design & Communication Graphics 2

3 Renaming a plane Right click on the plane in the Feature Manager Tree. Select Properties and type in the new name as shown. Hole Create the sketch for the hole on the diagonal plane as shown. Select Extrude Cut Select the mid plane option from the list and enter a depth of 300mm. Rename the feature hole Inserting 3 point plane Select, Plane, select through lines and points option, select the corners shown Click OK Rename the plane Cutting plane A plane may be renamed by clicking slowly on it twice on the Feature manager Tree. Design & Communication Graphics 3

4 Cutting a solid with a Plane From the Insert menu choose Cut, with surface select the cutting plane and click OK The side from which material is removed can be reversed as shown Inserting an Offset Plane Select, Plane, select the diagonal plane, insert a distance of 30mm Click OK Rename the plane Offset plane. Clock Face Create the sketch for the clock face on the offset plane as shown ensuring that the center of the circle for the clock face is coincident with the center of the hole. Select Extrude Boss/Base Choose the Blind option from the list and enter a Depth of 20mm. The sketch is the front of the feature. The direction of extrusion can be reversed by clicking on the button shown. Rename the feature Clock Face Design & Communication Graphics 4

5 Hiding Planes To hide a plane once it has been used right click on it on the Features Manager Tree and select Hide. Planes can be shown again if needed using the same method and selecting show. Hide the diagonal, cutting and offset planes. Mechanism Hole Create the sketch for the mechanism hole on the front of the clock face as shown; the centers are coincident. Select Extrude Cut, Choose the Through All option from the list Click OK Rename the feature mechanism hole. Pin Create a sketch on the top plane. Sketch a centerline coincident with the front face of the clock, as shown. Sketch the pin using centerline, circle and relations Design & Communication Graphics 5

6 Select Extrude Boss/ Base, Choose the up to surface option from the list Click OK Rename the feature pin. Textures Add the following textures to complete the finished Model: Clock Base and hole: Stone Marble1 Cut surface, Clock face and Mechanism hole: Stone Concrete 1 Pin: Wood Mahogany Lesson Complete! Design & Communication Graphics 6

7 Design & Communication Graphics 7

8 B) Roof (Inserting Planes) Getting Started Create a sketch on the right plane using the dimensions shown, use relations to ensure that the apex is vertical aligned with the origin Select Extrude Boss/ Base, Choose the midplane option enter a depth of 14m click OK Rename the feature main roof Design & Communication Graphics 8

9 Inserting a plane using an angle Select, Plane; select the line as shown and the top plane. It is necessary to expand the Feature Manager as shown to select the top plane Enter an angle of 35 deg Click OK Rename the plane right hip Cutting with a Plane From the Insert menu choose Cut, with surface, select the plane right hip, Check the arrow to make sure that the side being removed is correct Click OK Inserting Left hip Repeat the procedure above using an angle of 325 deg Hidden lines may be made visible to allow selection of edge Rename the plane left hip Cut the roof using this plane Design & Communication Graphics 9

10 Porch Create a sketch on the front plane using the dimensions shown, use relations to ensure that the apex is vertical aligned with the origin Select Extrude Boss/ Base, Choose the blind option enter a depth of 7m click OK Rename the feature porch Select shaded with edges Front Hip Insert a plane on the front of the porch with an angle of 60deg and use this to cut another hip Hide all 3 planes Colour Choose an appropriate colour for the roof. Lesson B Complete! Design & Communication Graphics 10

11 Design & Communication Graphics 11

12 Applications Design & Communication Graphics 12

Model House Exercise-( Extrude)

Model House Exercise-( Extrude) -( Extrude) Prerequisite knowledge Focus of the lesson Commands Used This lesson requires an understanding of using the sketch commands including Inserting a new sketch Adding sketch geometry Understanding

More information

Purlin Roof. Create a New Folder in your chosen location called Purlin Roof. The nine parts that make up the project will be saved here.

Purlin Roof. Create a New Folder in your chosen location called Purlin Roof. The nine parts that make up the project will be saved here. Purlin Roof Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Add Relations, Dimensioning), Inserting Planes, Extrude,

More information

Introduction to Circular Pattern Flower Pot

Introduction to Circular Pattern Flower Pot Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,

More information

Digital Camera Exercise

Digital Camera Exercise Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document

More information

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here. AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and

More information

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered

More information

Sash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1.

Sash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1. Sash Clamp 1 Introduction: The Sash clamp consists of nine parts. In creating the clamp we will be looking at the improvements made by SolidWorks in linear patterns, adding threads and in assembling the

More information

Introduction to Revolve - A Glass

Introduction to Revolve - A Glass Introduction to Revolve - A Glass Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Prerequisite Knowledge Previous knowledge of the following commands are required

More information

SolidWorks Design & Technology

SolidWorks Design & Technology SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one

More information

10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B

10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B Chevy Malibu Vehicle Design with Solidworks Start SolidWorks Create a New SolidWorks Document Miles, Rowardo B 1 Click: Part and then OK Now you are ready to make a Part. 2 Right Toolbar: Document Properties:

More information

Toothbrush Holder. A drawing of the sheet metal part will also be created.

Toothbrush Holder. A drawing of the sheet metal part will also be created. Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit

More information

EXERCISE ONE: BEACH BUGGY.

EXERCISE ONE: BEACH BUGGY. EXERCISE ONE: BEACH BUGGY. Prerequisite knowledge Students should have completed Exercises from the file: Introduction to Assemblies Concept Mates Focus of lesson Commands Used This lesson will focus on

More information

Quick Start for Autodesk Inventor

Quick Start for Autodesk Inventor Quick Start for Autodesk Inventor Autodesk Inventor Professional is a 3D mechanical design tool with powerful solid modeling capabilities and an intuitive interface. In this lesson, you use a typical workflow

More information

Engineering Technology

Engineering Technology Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,

More information

1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define.

1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define. BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Control + Click HERE to view enlarged IMAGE and Construction Strategy he following set of

More information

Shaft Hanger - SolidWorks

Shaft Hanger - SolidWorks ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric

More information

SolidWorks 95 User s Guide

SolidWorks 95 User s Guide SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents

More information

SolidWorks Reference Geometry

SolidWorks Reference Geometry SolidWorks Reference Geometry IDeATe Laser Micro Part 2 Dave Touretzky and Susan Finger 1. Symmetry and Reference Geometry Today, you ll make this part bear-like face and then cut it on the laser cutter:

More information

Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.

Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar. Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click

More information

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects Engineering Design with SolidWorks 2010 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling Introductory Level

More information

Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS

Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling

More information

Hydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).

Hydro Hull. Chapter 21. Boat. A. Save as HYDRO. Step 1. Open your HULL MID PLANE file (Chapter 2). Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,

More information

Introduction to Sweep - Allen Key part (A)

Introduction to Sweep - Allen Key part (A) Introduction to Sweep - Allen Key part (A) Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson, sketching (line construction, dimensioning, polygon).

More information

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008 1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical

More information

Engineering & Computer Graphics Workbook Using SOLIDWORKS

Engineering & Computer Graphics Workbook Using SOLIDWORKS Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.

Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch. Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click

More information

Introduction to Sheet Metal Features SolidWorks 2009

Introduction to Sheet Metal Features SolidWorks 2009 SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to

More information

Engineering & Computer Graphics Workbook Using SolidWorks 2014

Engineering & Computer Graphics Workbook Using SolidWorks 2014 Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

< Then click on this icon on the vertical tool bar that pops up on the left side.

< Then click on this icon on the vertical tool bar that pops up on the left side. Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts

More information

SolidWorks 103: Barge Design Challenge

SolidWorks 103: Barge Design Challenge SolidWorks 103: Barge Design Challenge Note: This tutorial was created using SolidWorks 2009. If you are using another version of SolidWorks, you may notice some variation in display states and configuration.

More information

Lesson 10: Loft Features

Lesson 10: Loft Features 10 Goals of This Lesson Your students will be able to create the following part: profiles chisel This lesson plan corresponds to the Loft Features chapter of SolidWorks Getting Started. SolidWorks Student

More information

SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.

SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P. 2001Plus A Competency Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com Project 2 Below are the desired

More information

Modeling an Airframe Tutorial

Modeling an Airframe Tutorial EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If

More information

Spatula. Spatula SW 2015 Design & Communication Graphics Page 1

Spatula. Spatula SW 2015 Design & Communication Graphics Page 1 Spatula Introduction: The model shown in the picture is made of three parts, - the base, the washer and the handle. The base requires the use of Spline and Style Spline command, Slot command and Mirror

More information

Understanding Projection Systems

Understanding Projection Systems Understanding Projection Systems A Point: A point has no dimensions, a theoretical location that has neither length, width nor height. A point shows an exact location in space. It is important to understand

More information

Below are the desired outcomes and usage competencies based on the completion of Project 4.

Below are the desired outcomes and usage competencies based on the completion of Project 4. Engineering Design with SolidWorks Project 4 Below are the desired outcomes and usage competencies based on the completion of Project 4. Project Desired Outcomes: An understanding of the customer s requirements

More information

How to Build a Game Console. David Hunt, PE

How to Build a Game Console. David Hunt, PE How to Build a Game Console David Hunt, PE davidhunt@outdrs.net Covering: Drafts Fillets Shells Patterns o Linear o Circular Using made-for-the-purpose sketches to define reference geometry Using reference

More information

Introduction to 3D CAD with SolidWorks. Jianan Li

Introduction to 3D CAD with SolidWorks. Jianan Li Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,

More information

WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer

WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer WEEK 5: Shaft Modeling (C51X01, C51X02) Revolved Features, Chamfer 1. Creating the Shaft Model 1. File> New> Part, Name: C51X01> OK 2. Insert> Revolve> Placement> Define> select TOP datum plane> Sketch

More information

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05 Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating

More information

Solidworks: Lesson 4 Assembly Basics and Toolbox. UCF Engineering

Solidworks: Lesson 4 Assembly Basics and Toolbox. UCF Engineering Solidworks: Lesson 4 Assembly Basics and Toolbox UCF Engineering Solidworks We have now completed the basic features of part modeling and it is now time to begin constructing more complex models in the

More information

Computer Aided Design Module 2. Lesson Toblerone Bar

Computer Aided Design Module 2. Lesson Toblerone Bar Computer Aided Design Module 2 Lesson Toblerone Bar Lesson? Toblerone Bar New Commands used: Polygon, Add Relations, Smart Dimension, Extrude Boss/Base (Mid Plane), Fillet, Line, Extrude-Cut, Linear Pattern

More information

Foreword. If you have any questions about these tutorials, drop your mail to

Foreword. If you have any questions about these tutorials, drop your mail to Foreword The main objective of these tutorials is to give you a kick start using Solidworks. The approach to write this tutorial is based on what is the most important knowledge you should know and what

More information

Solidworks Tutorial Pencil

Solidworks Tutorial Pencil The following instructions will be used to help you create a Pencil using Solidworks. These instructions are ordered to make the process as simple as possible. Deviating from the order, or not following

More information

SolidWorks Navigation

SolidWorks Navigation SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length

More information

g. Click once on the left vertical line of the rectangle.

g. Click once on the left vertical line of the rectangle. This drawing will require you to a model of a truck as a Solidworks Part. Please be sure to read the directions carefully before constructing the truck in Solidworks. Before submitting you will be required

More information

ME Week 2 Project 2 Flange Manifold Part

ME Week 2 Project 2 Flange Manifold Part 1 Project 2 - Flange Manifold Part 1.1 Instructions This project focuses on additional sketching methods and sketching commands. Revolve and Work features are also introduced. The part being modeled is

More information

DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY

DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY CAPSULE PROGRAM Funded by NSF grant #0833636 Tutorial 02 3D Part Modeling SolidWorks 2010 Copyright 2010 Prof. Zeid 3D Part Modeling

More information

Advance Dimensioning and Base Feature Options

Advance Dimensioning and Base Feature Options Chapter 4 Advance Dimensioning and Base Feature Options Learning Objectives After completing this chapter you will be able to: Dimension the sketch using the autodimension sketch tool. Dimension the sketch

More information

Lesson 6 2D Sketch Panel Tools

Lesson 6 2D Sketch Panel Tools Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,

More information

Introduction to Autodesk Inventor for F1 in Schools (Australian Version)

Introduction to Autodesk Inventor for F1 in Schools (Australian Version) Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital

More information

Part 8: The Front Cover

Part 8: The Front Cover Part 8: The Front Cover 4 Earpiece cuts and housing Lens cut and housing Microphone cut and housing The front cover is similar to the back cover in that it is a shelled protrusion with screw posts extruding

More information

1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry

1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry 2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply

More information

Wireless Mouse Surfaces

Wireless Mouse Surfaces Wireless Mouse Surfaces Design & Communication Graphics Table of Contents Table of Contents... 1 Introduction 2 Mouse Body. 3 Edge Cut.12 Centre Cut....14 Wheel Opening.. 15 Wheel Location.. 16 Laser..

More information

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.

Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch. Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.

More information

From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select

From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select Chapter 5 In sweep command there is a) Two sketch profiles b) Two path c) One sketch profile and one path The sweep profile is used to create threads springs circular things and difficult geometry. For

More information

Introducing SolidWorks

Introducing SolidWorks Introducing SolidWorks SAAST Robotics 2008 SolidWorks Software Visually-based 3-D Mechanical design software Engineers and Designers use it to: Quickly sketch out ideas Experiment with features, dimensions

More information

Siemens NX11 tutorials. The angled part

Siemens NX11 tutorials. The angled part Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure

More information

Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:

Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B: MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing

More information

Creo Parametric 2.0: Introduction to Solid Modeling. Creo Parametric 2.0: Introduction to Solid Modeling

Creo Parametric 2.0: Introduction to Solid Modeling. Creo Parametric 2.0: Introduction to Solid Modeling Creo Parametric 2.0: Introduction to Solid Modeling 1 2 Part 1 Class Files... xiii Chapter 1 Introduction to Creo Parametric... 1-1 1.1 Solid Modeling... 1-4 1.2 Creo Parametric Fundamentals... 1-6 Feature-Based...

More information

Lesson 4 Holes and Rounds

Lesson 4 Holes and Rounds Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information

More information

SOLIDWORKS 2016 Advanced Techniques

SOLIDWORKS 2016 Advanced Techniques SOLIDWORKS 2016 Advanced Techniques Mastering Parts, Surfaces, Sheet Metal, SimulationXpress, Top Down Assemblies, Core & Cavity Molds Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices.

More information

On completion of this exercise you will have:

On completion of this exercise you will have: Prerequisite Knowledge To complete this exercise you will need; to be familiar with the SolidWorks interface and the key commands. basic file management skills the ability to rotate views and select faces

More information

Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.

Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P. Engineering Design with SolidWorks 2003 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com

More information

Datum Tutorial Part: Cutter

Datum Tutorial Part: Cutter Datum Tutorial Part: Cutter Objective: Learn to apply Datums in different ways Directions 1. Datum Axis Creation a. First we need to create a center axis for the cutter b. Model Tab > Datum > Select Axis

More information

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece

Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece 1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a

More information

Lesson 4 Extrusions OBJECTIVES. Extrusions

Lesson 4 Extrusions OBJECTIVES. Extrusions Lesson 4 Extrusions Figure 4.1 Clamp OBJECTIVES Create a feature using an Extruded protrusion Understand Setup and Environment settings Define and set a Material type Create and use Datum features Sketch

More information

Revit Structure 2012 Basics:

Revit Structure 2012 Basics: SUPPLEMENTAL FILES ON CD Revit Structure 2012 Basics: Framing and Documentation Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Structural

More information

Solidworks tutorial. 3d sketch project. A u t h o r : M. G h a s e m i. C o n t a c t u s : i n f s o l i d w o r k s a d v i s o r.

Solidworks tutorial. 3d sketch project. A u t h o r : M. G h a s e m i. C o n t a c t u s : i n f s o l i d w o r k s a d v i s o r. Solidworks tutorial 3d sketch project A u t h o r : M. G h a s e m i C o n t a c t u s : i n f o @ s o l i d w o r k s a d v i s o r. c o m we will create this frame during the tutorial : In this tutorial

More information

Table of Contents. Lesson 1 Getting Started

Table of Contents. Lesson 1 Getting Started NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard

More information

Draft Analysis Tools 1 Tuula Höök, Tampere University of Technology

Draft Analysis Tools 1 Tuula Höök, Tampere University of Technology Draft Analysis Tools 1 Tuula Höök, Tampere University of Technology What is new in this exercise? - Draft analysis tool - Undercut analysis tool - Drafting faces with a neutral plane - Modifications to

More information

CREO.1 MODELING A BELT WHEEL

CREO.1 MODELING A BELT WHEEL CREO.1 MODELING A BELT WHEEL Figure 1: A belt wheel modeled in this exercise. Learning Targets In this exercise you will learn: Using symmetry when sketching Using pattern to copy features Using RMB when

More information

Product Modelling in Solid Works

Product Modelling in Solid Works Product Modelling in Solid Works In the following exercise you will use solid works to construct the computer mouse shown opposite. In this exercise you will use a number of advanced features to achieve

More information

Pro/E WILDFIRE, week6

Pro/E WILDFIRE, week6 Pro/E WILDFIRE, week6 1. Set working directory 2. File>New>Name is lbrack 3. When you create the part, make sure that the back surface of the vertical plate is on the front datum plane, and the lower surface

More information

for Solidworks TRAINING GUIDE LESSON-9-CAD

for Solidworks TRAINING GUIDE LESSON-9-CAD for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working

More information

Introduction to Parametric Modeling AEROPLANE. Design & Communication Graphics 1

Introduction to Parametric Modeling AEROPLANE. Design & Communication Graphics 1 AEROPLANE Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Aeroplane Assembly The part files for this assembly are saved in the folder titled Aeroplane. Open an

More information

Using Siemens NX 11 Software. The connecting rod

Using Siemens NX 11 Software. The connecting rod Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open

More information

SolidWorks 2005 Tutorial. and MultiMedia CD. A Step-by-step Project Based Approach Utilizing 3D Solid Modeling

SolidWorks 2005 Tutorial. and MultiMedia CD. A Step-by-step Project Based Approach Utilizing 3D Solid Modeling INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects SolidWorks 2005 Tutorial and MultiMedia CD A Step-by-step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard

More information

NX 7.5. Table of Contents. Lesson 3 More Features

NX 7.5. Table of Contents. Lesson 3 More Features NX 7.5 Lesson 3 More Features Pre-reqs/Technical Skills Basic computer use Completion of NX 7.5 Lessons 1&2 Expectations Read lesson material Implement steps in software while reading through lesson material

More information

Part 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion.

Part 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion. Part 2: Earpiece 4 Round extrusion Radial pattern Chamfered edge To create this part, you'll use some of the same extrusion techniques you used in the lens part. The only difference in this part is that

More information

Solid Part Four A Bracket Made by Mirroring

Solid Part Four A Bracket Made by Mirroring C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude

More information

Inventor-Parts-Tutorial By: Dor Ashur

Inventor-Parts-Tutorial By: Dor Ashur Inventor-Parts-Tutorial By: Dor Ashur For Assignment: http://www.maelabs.ucsd.edu/mae3/assignments/cad/inventor_parts.pdf Open Autodesk Inventor: Start-> All Programs -> Autodesk -> Autodesk Inventor 2010

More information

Chapter 2. Modifying, Extruding and Revolving the Sketches. Learning Objectives. Commands Covered AMMODDIM AMEXTRUDE AMREVOLVE

Chapter 2. Modifying, Extruding and Revolving the Sketches. Learning Objectives. Commands Covered AMMODDIM AMEXTRUDE AMREVOLVE Chapter 2 Modifying, Extruding and Revolving the Sketches Learning Objectives After completing this chapter, you will be able to: Modify the desired sketch using the AMMODDIM command. Extrude the desired

More information

Laboratory Demonstration Exercises

Laboratory Demonstration Exercises Laboratory Demonstration Exercises 3-1 Lab Demo 1 - Plus Block Open SolidWorks, click on new document part OK. Right Click on Front Plane, click on Sketch icon (pencil w/ axes). In the sketch toolbar on

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2008 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better

More information

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry 4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are

More information

Tech-World Manufacturing. Design. Level two. CELL Guide. Edition E0

Tech-World Manufacturing. Design. Level two. CELL Guide. Edition E0 Tech-World Manufacturing Design Level two Edition 5 37186-E0 FIFTH EDITION First Printing, February 2011 Copyright 2005, 2006, 2007, 2008, 2009, 2010, 2011 Lab-Volt Systems, Inc. All rights reserved.

More information

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Part Tutorial Exercise 5: Loft-Tube-1 [Complete] In this Exercise, We will set System Parameters first, then part options. Then, in sketch

More information

Module 2.1, 2.2 Review. EF101 Analysis & Skills Module 2.3. Sketched Features and Operations. On-line Help Two Locations

Module 2.1, 2.2 Review. EF101 Analysis & Skills Module 2.3. Sketched Features and Operations. On-line Help Two Locations EF101 Analysis & Skills Module 2.3 Engineering Graphics Revolved Features Placed Features Work Features Module 2.1, 2.2 Review What are the three types of operations for adding features to the base feature?

More information

Getting Started. Before You Begin, make sure you customized the following settings:

Getting Started. Before You Begin, make sure you customized the following settings: Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides

More information

SolidWorks Tutorial 1. Axis

SolidWorks Tutorial 1. Axis SolidWorks Tutorial 1 Axis Axis This first exercise provides an introduction to SolidWorks software. First, we will design and draw a simple part: an axis with different diameters. You will learn how to

More information

ENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems

ENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems Spring Semester 2016 ENGR 1182 Exam 1 First Mid Term Exam Study Guide and Practice Problems Disclaimer Problems in this study guide resemble problems relating mainly to the pertinent homework assignments.

More information

Part Design. Sketcher - Basic 1 13,0600,1488,1586(SP6)

Part Design. Sketcher - Basic 1 13,0600,1488,1586(SP6) Part Design Sketcher - Basic 1 13,0600,1488,1586(SP6) In this exercise, we will learn the foundation of the Sketcher and its basic functions. The Sketcher is a tool used to create two-dimensional (2D)

More information

Revit Structure 2014 Basics

Revit Structure 2014 Basics Revit Structure 2014 Basics Framing and Documentation Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2005 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com

More information

Creo Revolve Tutorial

Creo Revolve Tutorial Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate

More information

Top Down Assembly Modeling Release Wildfire 2.0

Top Down Assembly Modeling Release Wildfire 2.0 Top Down Assembly Modeling Release Wildfire 2.0 Note: Comprehensive Modeling Assignment This is a 30 point assignment as such takes the place of the final exam. Four Plate Mold Base, Inner Two Plates Begin

More information

F1 in Schools Tutorial 3 A Step by Step Guide To Drawing an. F1 Block In SolidWorks

F1 in Schools Tutorial 3 A Step by Step Guide To Drawing an. F1 Block In SolidWorks F in Schools Tutorial A Step by Step Guide To Drawing an F Block In SolidWorks There are 7 Achievement Points to Collect During This Tutorial! Requirements: SolidWorks Student Edition or SolidWorks Design

More information