DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY

Size: px
Start display at page:

Download "DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY"

Transcription

1 DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY CAPSULE PROGRAM Funded by NSF grant # Tutorial 02 3D Part Modeling SolidWorks 2010 Copyright 2010 Prof. Zeid

2 3D Part Modeling In this tutorial you learn 3D part modeling and sketch control. We create three parts: pin, rectangular plate, and base plate Pin Step 0: General Planning Strategy: We shall create the part shown in the image below. Listed below the figure are the steps in brief that we must perform to create the part. 1. Create and revolve the profile. 2

3 Creating the Pin Step 1 File New Part 3

4 Step 2 Select Front Plane from the feature manager 4

5 Step 3 Select Front View from view orientation icon 5

6 Step 4 Go to Tools Options 6

7 Step 5 Go to Document properties Units IPS 7

8 The IPS unit is selected for the drawing. The drawing will now have inches as its unit. 8

9 Step 6 Select Sketch Tab Then select Line Icon 2) Select Line Icon 1) Select Sketch Tab 9

10 Step 7 Draw the drawing as per required dimensions When you select line icon a red axis point will appear. Start the drawing from the red point. Once you finish drawing select OK 10

11 Step 8 Go to Features Tab Reference Geometries Axis 11

12 Step 9 4) After drawing axis select ok 1) One line/edge/axis 3) Click mouse here (end point) 2) Click mouse here (start point) 12

13 Step 10 Now we are ready to perform the revolve operation. 13

14 Step 11 Go to Feature Manager and select Sketch Then select Revolved Boss/Base icon 2) Select Revolved Boss/Base icon 1) Select Sketch 14

15 Step 12 1) Select the blue box 2) Select the axis 15

16 Step 13 The rotated entity preview will be shown as in the image below 1) Select Ok 16

17 The rotated entity preview will be shown as in the image below 17

18 The rotated entity preview will be shown as in the image below 18

19 The dimensions of the pin are shown in the image below. 19

20 Rectangular Plate General Planning Strategy We shall create the part shown in the image below. Listed below the figure are the steps in brief that we must perform to create the part. 2. Create the profile and extrude it to create the plate. 3. Create the hole. 20

21 Step 1 Create the part file and draw the rectangle according to required dimensions. For creating part file and drawing refer to the pin tutorial. 21

22 Step2 After completing the drawing change the view to isometric and select OK. 1) Select Isometric view 2) Select Ok 22

23 Step 3 Select sketch from the Feature Manager. 23

24 Step 4 Select Extruded Boss/Base from Features Tab. Enter the dimension as 3 inches. 1) Select Extruded Boss/base 3) Select OK 2) Enter dimension as 3 inches 24

25 Preview of the rectangular plate. 25

26 Step 5 Select the top plane of the rectangular plate. 26

27 Step 6 Go to View Icon and select Normal To option 27

28 Step 7 Select Circle Icon. 28

29 Step 8 Draw a circle of diameter 1 inch. Adjust the placement of the circle using smart dimension option. Tutorial 1 has the steps on how to use the smart dimension option. 1) After drawing the circle select OK 29

30 Preview of the Rectangular plate. 30

31 Step 9 Select sketch from the Feature Manager. 31

32 Step 10 Go to Features Tab Extruded Boss/base. Select the option Through All. 1) Select the option Through all 32

33 Preview of the completed Rectangular Plate. 33

34 This completes the model. Shown below is the dimensioned drawing view of the model that we just created. 34

35 Base Plate General Planning Strategy We shall create the part shown in the image below. Listed below the figure are the steps in brief that we must perform to create the part. 4. Create the profile and extrude it to create the plate. 5. Create the hole. 35

36 Step 1 Create the part file and draw the figure according to required dimensions. For creating part file and drawing refer to the pin tutorial. 36

37 Step 2 View the drawing in Isometric View. Select sketch from the Feature Manager. 37

38 Step 3 Go to Features Tab Extruded Boss/base and extrude the figure to a length of 3 inches. Select Ok (green tick mark on top right corner) to complete extrusion. 38

39 Preview of the extruded part. 39

40 Step 4 Select the plane as shown in the figure below. 40

41 Step 5 Select Normal To option from the View Icon. 41

42 Step 6 Draw a circle of diameter 1 inch. Position the circle using smart dimension option. Follow the steps given in the tutorial for rectangular plate on how to use the smart dimension option. Select OK to complete the process. 42

43 Step 7 Select the circle sketch from the Feature Manager Window. 43

44 Step 8 Go to Features Tab Extruded Boss/base and use the option Through All. Select OK to complete the extrusion. 44

45 Preview of the completed model. 45

46 This completes the model. Shown below is the dimensioned drawing view of the model that we just created. Save the models with the name pin, rectangular plate and base plate. 46

From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select

From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select Chapter 5 In sweep command there is a) Two sketch profiles b) Two path c) One sketch profile and one path The sweep profile is used to create threads springs circular things and difficult geometry. For

More information

Digital Camera Exercise

Digital Camera Exercise Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document

More information

SolidWorks Reference Geometry

SolidWorks Reference Geometry SolidWorks Reference Geometry IDeATe Laser Micro Part 2 Dave Touretzky and Susan Finger 1. Symmetry and Reference Geometry Today, you ll make this part bear-like face and then cut it on the laser cutter:

More information

Introduction to Circular Pattern Flower Pot

Introduction to Circular Pattern Flower Pot Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,

More information

Creo Revolve Tutorial

Creo Revolve Tutorial Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate

More information

g. Click once on the left vertical line of the rectangle.

g. Click once on the left vertical line of the rectangle. This drawing will require you to a model of a truck as a Solidworks Part. Please be sure to read the directions carefully before constructing the truck in Solidworks. Before submitting you will be required

More information

SolidWorks Navigation

SolidWorks Navigation SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length

More information

Cube in a cube Fusion 360 tutorial

Cube in a cube Fusion 360 tutorial Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.

More information

Introduction to Revolve - A Glass

Introduction to Revolve - A Glass Introduction to Revolve - A Glass Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Prerequisite Knowledge Previous knowledge of the following commands are required

More information

Shaft Hanger - SolidWorks

Shaft Hanger - SolidWorks ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric

More information

Starting a 3D Modeling Part File

Starting a 3D Modeling Part File 1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce

More information

SolidWorks Design & Technology

SolidWorks Design & Technology SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one

More information

Foreword. If you have any questions about these tutorials, drop your mail to

Foreword. If you have any questions about these tutorials, drop your mail to Foreword The main objective of these tutorials is to give you a kick start using Solidworks. The approach to write this tutorial is based on what is the most important knowledge you should know and what

More information

Engineering & Computer Graphics Workbook Using SolidWorks 2014

Engineering & Computer Graphics Workbook Using SolidWorks 2014 Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

Name: Date Completed: Basic Inventor Skills I

Name: Date Completed: Basic Inventor Skills I Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.

More information

Engineering & Computer Graphics Workbook Using SOLIDWORKS

Engineering & Computer Graphics Workbook Using SOLIDWORKS Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)

More information

Veerapandian.K Mechanical Engg Vedharanyam A manual to mechanical designers How Solid works Works?

Veerapandian.K Mechanical Engg Vedharanyam A manual to mechanical designers How Solid works Works? Compiled by Veerapandian.K Mechanical Engg Vedharanyam-614 810 A manual to mechanical designers How Solid works Works? Solid works Overview Solid works main idea is user to create drawing directly in 3D

More information

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI

SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered

More information

SolidWorks Tutorial 1. Axis

SolidWorks Tutorial 1. Axis SolidWorks Tutorial 1 Axis Axis This first exercise provides an introduction to SolidWorks software. First, we will design and draw a simple part: an axis with different diameters. You will learn how to

More information

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008

Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008 1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical

More information

for Solidworks TRAINING GUIDE LESSON-9-CAD

for Solidworks TRAINING GUIDE LESSON-9-CAD for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working

More information

Creo Extrude Tutorial 2: Cutting and Adding Material

Creo Extrude Tutorial 2: Cutting and Adding Material Creo Extrude Tutorial 2: Cutting and Adding Material 1. Open Creo Parametric 2. File > Open > extrudeturial (From Creo Extrude Tutorial 1) 3. Cutting Material a. Click Extrude Icon > Select the following

More information

LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets

LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets Set units Create Sketch Add relations Linear patterns Mirror Fillet Extrude Extrude cut First, set units. click Option on top of main menu Open Document Properties

More information

Introduction to 3D CAD with SolidWorks. Jianan Li

Introduction to 3D CAD with SolidWorks. Jianan Li Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,

More information

Introduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software

Introduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software Introduction to 3D Printing Activity 1: Design a keychain using computer-aided design software 1 In this activity we ll design a keychain name tag and learn the fundamentals of computer-aided design, the

More information

EXERCISE ONE: BEACH BUGGY.

EXERCISE ONE: BEACH BUGGY. EXERCISE ONE: BEACH BUGGY. Prerequisite knowledge Students should have completed Exercises from the file: Introduction to Assemblies Concept Mates Focus of lesson Commands Used This lesson will focus on

More information

SolidWorks 103: Barge Design Challenge

SolidWorks 103: Barge Design Challenge SolidWorks 103: Barge Design Challenge Note: This tutorial was created using SolidWorks 2009. If you are using another version of SolidWorks, you may notice some variation in display states and configuration.

More information

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.

AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here. AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and

More information

Top Down Assembly Modeling Release Wildfire 2.0

Top Down Assembly Modeling Release Wildfire 2.0 Top Down Assembly Modeling Release Wildfire 2.0 Note: Comprehensive Modeling Assignment This is a 30 point assignment as such takes the place of the final exam. Four Plate Mold Base, Inner Two Plates Begin

More information

Solid Part Four A Bracket Made by Mirroring

Solid Part Four A Bracket Made by Mirroring C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude

More information

Engineering Innovation Center Fabrication Shop Basic CAD Training

Engineering Innovation Center Fabrication Shop Basic CAD Training Engineering Innovation Center Fabrication Shop Basic CAD Training Introduction The Engineering Innovation Center Fabrication Shop was established for support of undergraduate student course work. Every

More information

Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS

Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling

More information

Nut and Bolt Tutorial

Nut and Bolt Tutorial Thread Representations Nut and Bolt Tutorial Parts to a Thread Thread Dimensioning Major Diameter Thread Series (IE UNC, UNF, ACME, etc) ½ - 13 UNC 2 A or B A = External B = Internal Threads per Inch Class

More information

F1 in Schools Tutorial 1 A Step by Step Guide To Drawing a. Bloodhound Block In SolidWorks

F1 in Schools Tutorial 1 A Step by Step Guide To Drawing a. Bloodhound Block In SolidWorks F in Schools Tutorial A Step by Step Guide To Drawing a Bloodhound Block In SolidWorks There are 7 Achievement Points to Collect During This Tutorial! Requirements: SolidWorks Student Edition or SolidWorks

More information

Lesson 10: Loft Features

Lesson 10: Loft Features 10 Goals of This Lesson Your students will be able to create the following part: profiles chisel This lesson plan corresponds to the Loft Features chapter of SolidWorks Getting Started. SolidWorks Student

More information

10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B

10/14/2010. Chevy Malibu. Vehicle Design with Solidworks. Start SolidWorks Create a New SolidWorks Document. Miles, Rowardo B Chevy Malibu Vehicle Design with Solidworks Start SolidWorks Create a New SolidWorks Document Miles, Rowardo B 1 Click: Part and then OK Now you are ready to make a Part. 2 Right Toolbar: Document Properties:

More information

Solidworks tutorial. 3d sketch project. A u t h o r : M. G h a s e m i. C o n t a c t u s : i n f s o l i d w o r k s a d v i s o r.

Solidworks tutorial. 3d sketch project. A u t h o r : M. G h a s e m i. C o n t a c t u s : i n f s o l i d w o r k s a d v i s o r. Solidworks tutorial 3d sketch project A u t h o r : M. G h a s e m i C o n t a c t u s : i n f o @ s o l i d w o r k s a d v i s o r. c o m we will create this frame during the tutorial : In this tutorial

More information

J. La Favre Fusion 360 Lesson 5 April 24, 2017

J. La Favre Fusion 360 Lesson 5 April 24, 2017 In this lesson, you will create a funnel like the one in the illustration to the left. The main purpose of this lesson is to introduce you to the use of the Revolve tool. The Revolve tool is similar to

More information

Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly

Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly Patterning a sketched feature (such as a slot, rib, square, etc.,) requires a slightly different technique. Why can t we create a

More information

Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.

Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch. Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click

More information

Sash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1.

Sash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1. Sash Clamp 1 Introduction: The Sash clamp consists of nine parts. In creating the clamp we will be looking at the improvements made by SolidWorks in linear patterns, adding threads and in assembling the

More information

Model House Exercise-( Extrude)

Model House Exercise-( Extrude) -( Extrude) Prerequisite knowledge Focus of the lesson Commands Used This lesson requires an understanding of using the sketch commands including Inserting a new sketch Adding sketch geometry Understanding

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2005 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com

More information

Van Assembly. Creating an Assembly. Original by Steven Jaffe Modified by E. Brunelle 2/07 1

Van Assembly. Creating an Assembly. Original by Steven Jaffe Modified by E. Brunelle 2/07 1 Van Assembly Creating an Assembly 1 Part One the Axle 1. Set Units to Inches 2. Create a New Design. 3. Save the Design as axleinl_cad1_1 in your Van folder. 4. Create a New Sketch on the Lateral workplane.

More information

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material

Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2008 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better

More information

F1 in Schools Tutorial 3 A Step by Step Guide To Drawing an. F1 Block In SolidWorks

F1 in Schools Tutorial 3 A Step by Step Guide To Drawing an. F1 Block In SolidWorks F in Schools Tutorial A Step by Step Guide To Drawing an F Block In SolidWorks There are 7 Achievement Points to Collect During This Tutorial! Requirements: SolidWorks Student Edition or SolidWorks Design

More information

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1

Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Part Tutorial Exercise 5: Loft-Tube-1 [Complete] In this Exercise, We will set System Parameters first, then part options. Then, in sketch

More information

When you complete this assignment you will:

When you complete this assignment you will: Objjectiives When you complete this assignment you will: 1. sketch and create models using new work planes and the loft command. 2. sketch and create models using the revolve command. 3. sketch and dimension

More information

Solidworks Tutorial Pencil

Solidworks Tutorial Pencil The following instructions will be used to help you create a Pencil using Solidworks. These instructions are ordered to make the process as simple as possible. Deviating from the order, or not following

More information

Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.

Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar. Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click

More information

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling

Engineering Design. with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects Engineering Design with SolidWorks 2010 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling Introductory Level

More information

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05

Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05 Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating

More information

1. Change units to inches: Tools > Options > Document Properties > Units and then select: IPS (inch, pound, second)

1. Change units to inches: Tools > Options > Document Properties > Units and then select: IPS (inch, pound, second) Steps to Draw Pump Impeller: The steps below show one way to draw the impeller. You should make sure that your impeller is not larger than the one shown or it may not fit in the pump housing. 1. Change

More information

Solidworks: Lesson 4 Assembly Basics and Toolbox. UCF Engineering

Solidworks: Lesson 4 Assembly Basics and Toolbox. UCF Engineering Solidworks: Lesson 4 Assembly Basics and Toolbox UCF Engineering Solidworks We have now completed the basic features of part modeling and it is now time to begin constructing more complex models in the

More information

SolidWorks 2005 Tutorial. and MultiMedia CD. A Step-by-step Project Based Approach Utilizing 3D Solid Modeling

SolidWorks 2005 Tutorial. and MultiMedia CD. A Step-by-step Project Based Approach Utilizing 3D Solid Modeling INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects SolidWorks 2005 Tutorial and MultiMedia CD A Step-by-step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard

More information

Modeling Basic Mechanical Components #1 Tie-Wrap Clip

Modeling Basic Mechanical Components #1 Tie-Wrap Clip Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely

More information

Below are the desired outcomes and usage competencies based on the completion of Project 4.

Below are the desired outcomes and usage competencies based on the completion of Project 4. Engineering Design with SolidWorks Project 4 Below are the desired outcomes and usage competencies based on the completion of Project 4. Project Desired Outcomes: An understanding of the customer s requirements

More information

Spatula. Spatula SW 2015 Design & Communication Graphics Page 1

Spatula. Spatula SW 2015 Design & Communication Graphics Page 1 Spatula Introduction: The model shown in the picture is made of three parts, - the base, the washer and the handle. The base requires the use of Spline and Style Spline command, Slot command and Mirror

More information

LABORATORY MANUAL COMPUTER AIDED DESIGN LAB

LABORATORY MANUAL COMPUTER AIDED DESIGN LAB LABORATORY MANUAL COMPUTER AIDED DESIGN LAB Sr. No 1 2 3 Experiment Title Setting up of drawing environment by setting drawing limits, drawing units, naming the drawing, naming layers, setting line types

More information

Introducing SolidWorks

Introducing SolidWorks Introducing SolidWorks SAAST Robotics 2008 SolidWorks Software Visually-based 3-D Mechanical design software Engineers and Designers use it to: Quickly sketch out ideas Experiment with features, dimensions

More information

Lesson 4 Holes and Rounds

Lesson 4 Holes and Rounds Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information

More information

1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define.

1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define. BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Control + Click HERE to view enlarged IMAGE and Construction Strategy he following set of

More information

Computer Aided Design Module 2. Lesson Toblerone Bar

Computer Aided Design Module 2. Lesson Toblerone Bar Computer Aided Design Module 2 Lesson Toblerone Bar Lesson? Toblerone Bar New Commands used: Polygon, Add Relations, Smart Dimension, Extrude Boss/Base (Mid Plane), Fillet, Line, Extrude-Cut, Linear Pattern

More information

Hydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).

Hydro Hull. Chapter 21. Boat. A. Save as HYDRO. Step 1. Open your HULL MID PLANE file (Chapter 2). Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,

More information

Pull Down Menu View Toolbar Design Toolbar

Pull Down Menu View Toolbar Design Toolbar Pro/DESKTOP Interface The instructions in this tutorial refer to the Pro/DESKTOP interface and toolbars. The illustration below describes the main elements of the graphical interface and toolbars. Pull

More information

Toothbrush Holder. A drawing of the sheet metal part will also be created.

Toothbrush Holder. A drawing of the sheet metal part will also be created. Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit

More information

SolidWorks 95 User s Guide

SolidWorks 95 User s Guide SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents

More information

Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:

Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B: MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing

More information

Introduction to SolidWorks Introduction to SolidWorks

Introduction to SolidWorks Introduction to SolidWorks Introduction to SolidWorks Introduction to SolidWorks SolidWorks is a powerful 3D modeling program. The models it produces can be used in a number of ways to simulate the behaviour of a real part or assembly

More information

SolidWorks Training. Introductory course for staff and students from the School of Physics and Astronomy

SolidWorks Training. Introductory course for staff and students from the School of Physics and Astronomy SolidWorks Training Introductory course for staff and students from the School of Physics and Astronomy i) Introductory presentation SolidWorks Training ii) The SolidWorks GUI The SolidWorks Graphical

More information

Clock Exercise (Inserting Planes)

Clock Exercise (Inserting Planes) Clock Exercise (Inserting Planes) Prerequisite Knowledge To complete this exercise you will need to be familiar with Sketching, Applying relations, Extrude Boss/ Base, Extrude cut, Applying Textures, Renaming

More information

Drawing and Assembling

Drawing and Assembling Youth Explore Trades Skills Description In this activity the six sides of a die will be drawn and then assembled together. The intent is to understand how constraints are used to lock individual parts

More information

Engineering Technology

Engineering Technology Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,

More information

Activity Sketch Plane Cube

Activity Sketch Plane Cube Activity 1.5.4 Sketch Plane Cube Introduction Have you ever tried to explain to someone what you knew, and that person wanted you to tell him or her more? Here is your chance to do just that. You have

More information

Modeling an Airframe Tutorial

Modeling an Airframe Tutorial EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If

More information

Vehicle Dynamics and Design Creating a Chevy Malibu car in SolidWorks STEP 2: Go to top of page to Tools, then scroll down to Options.

Vehicle Dynamics and Design Creating a Chevy Malibu car in SolidWorks STEP 2: Go to top of page to Tools, then scroll down to Options. STEP 1: Open up SolidWorks 2008. (a) Choose a new part to open. (b) Click OK. Vehicle Dynamics and Design Creating a Chevy Malibu car in SolidWorks 2008 STEP 2: Go to top of page to Tools, then scroll

More information

Student + Instructor:

Student + Instructor: BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Show 01 Solid Modeling Intro slides quickly. SolidWorks Layout slides are on EEIC for reference

More information

Part 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion.

Part 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion. Part 2: Earpiece 4 Round extrusion Radial pattern Chamfered edge To create this part, you'll use some of the same extrusion techniques you used in the lens part. The only difference in this part is that

More information

Advanced Modeling Techniques Sweep and Helical Sweep

Advanced Modeling Techniques Sweep and Helical Sweep Advanced Modeling Techniques Sweep and Helical Sweep Sweep A sweep is a profile that follows a path placed on a datum. It is important when creating a sweep that the designer plans the size of the path

More information

Pro/DESKTOP Tutorial Drafting Bow Compass

Pro/DESKTOP Tutorial Drafting Bow Compass Pro/DESKTOP Tutorial Drafting Bow Compass Michael Flowers 2005 1 Objectives: To develop confidence with the Pro/DESKTOP software. To learn to utilize extrude, project, revolve, round, and chamfer features.

More information

Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.

Engineering Design with SolidWorks A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P. Engineering Design with SolidWorks 2003 A Step-by-Step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com

More information

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry

1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry 4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are

More information

ME Week 2 Project 2 Flange Manifold Part

ME Week 2 Project 2 Flange Manifold Part 1 Project 2 - Flange Manifold Part 1.1 Instructions This project focuses on additional sketching methods and sketching commands. Revolve and Work features are also introduced. The part being modeled is

More information

Introduction to Autodesk Inventor for F1 in Schools (Australian Version)

Introduction to Autodesk Inventor for F1 in Schools (Australian Version) Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital

More information

Create A Mug. Skills Learned. Settings Sketching 3-D Features. Revolve Offset Plane Sweep Fillet Decal* Offset Arc

Create A Mug. Skills Learned. Settings Sketching 3-D Features. Revolve Offset Plane Sweep Fillet Decal* Offset Arc Create A Mug Skills Learned Settings Sketching 3-D Features Slice Line Tool Offset Arc Revolve Offset Plane Sweep Fillet Decal* Tutorial: Creating A Custom Mug There are somethings in this world that have

More information

Inventor-Parts-Tutorial By: Dor Ashur

Inventor-Parts-Tutorial By: Dor Ashur Inventor-Parts-Tutorial By: Dor Ashur For Assignment: http://www.maelabs.ucsd.edu/mae3/assignments/cad/inventor_parts.pdf Open Autodesk Inventor: Start-> All Programs -> Autodesk -> Autodesk Inventor 2010

More information

Siemens NX11 tutorials. The angled part

Siemens NX11 tutorials. The angled part Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure

More information

Advance Dimensioning and Base Feature Options

Advance Dimensioning and Base Feature Options Chapter 4 Advance Dimensioning and Base Feature Options Learning Objectives After completing this chapter you will be able to: Dimension the sketch using the autodimension sketch tool. Dimension the sketch

More information

The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly.

The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly. Introduction - Teacher Notes Fig 1. The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly. Pro/DESKTOP enables pupils (and teachers) to communicate and model

More information

SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P.

SDC. SolidWorks Tutorial 2001Plus. A Competency Project Based Approach Utilizing 3D Solid Modeling. David C. Planchard & Marie P. 2001Plus A Competency Project Based Approach Utilizing 3D Solid Modeling David C. Planchard & Marie P. Planchard SDC PUBLICATIONS www.schroff.com www.schroff-europe.com Project 2 Below are the desired

More information

UNIT 11: Revolved and Extruded Shapes

UNIT 11: Revolved and Extruded Shapes UNIT 11: Revolved and Extruded Shapes In addition to basic geometric shapes and importing of three-dimensional STL files, SOLIDCast allows you to create three-dimensional shapes that are formed by revolving

More information

2809 CAD TRAINING: Part 1 Sketching and Making 3D Parts. Contents

2809 CAD TRAINING: Part 1 Sketching and Making 3D Parts. Contents Contents Getting Started... 2 Lesson 1:... 3 Lesson 2:... 13 Lesson 3:... 19 Lesson 4:... 23 Lesson 5:... 25 Final Project:... 28 Getting Started Get Autodesk Inventor Go to http://students.autodesk.com/

More information

AutoCAD Inventor - Solid Modeling, Stress and Dynamic Analysis

AutoCAD Inventor - Solid Modeling, Stress and Dynamic Analysis PDHonline Course G280 (15 PDH) AutoCAD Inventor - Solid Modeling, Stress and Dynamic Analysis Instructor: John R. Andrew, P.E. 2012 PDH Online PDH Center 5272 Meadow Estates Drive Fairfax, VA 22030-6658

More information

TOY TRUCK. Figure 1. Orthographic projections of project.

TOY TRUCK. Figure 1. Orthographic projections of project. TOY TRUCK Prepared by: Harry Hawkins The following project is of a small, wooden toy truck. This exercise will provide you with the procedure for constructing the various parts of the design then assembling

More information

Evaluation Chapter by CADArtifex

Evaluation Chapter by CADArtifex The premium provider of learning products and solutions www.cadartifex.com EVALUATION CHAPTER 2 Drawing Sketches with SOLIDWORKS In this chapter: Invoking the Part Modeling Environment Invoking the Sketching

More information

Understanding Projection Systems

Understanding Projection Systems Understanding Projection Systems A Point: A point has no dimensions, a theoretical location that has neither length, width nor height. A point shows an exact location in space. It is important to understand

More information

Table of Contents. Lesson 1 Getting Started

Table of Contents. Lesson 1 Getting Started NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard

More information

How to Build a Game Console. David Hunt, PE

How to Build a Game Console. David Hunt, PE How to Build a Game Console David Hunt, PE davidhunt@outdrs.net Covering: Drafts Fillets Shells Patterns o Linear o Circular Using made-for-the-purpose sketches to define reference geometry Using reference

More information

Introduction to Sweep - Allen Key part (A)

Introduction to Sweep - Allen Key part (A) Introduction to Sweep - Allen Key part (A) Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson, sketching (line construction, dimensioning, polygon).

More information