Diane Burton, STEM Outreach.
|
|
- Belinda Cole
- 5 years ago
- Views:
Transcription
1 123D Design Tutorial: LED decoration Before using these instructions, it is very helpful to watch this video screencast of the CAD drawing actually being done in the software. Click this link for the video instructions Select Sketch Spline Start drawing your shape left clicking each time you want to place a node on the shape (nodes can be moved later to allow you to change the shape slightly. You must finish your drawing at the same place you started to close the sketch. When you ve done, this left click then press Enter to exit the sketch Your sketch should turn blue as below. Use Construct Extrude to extrude the shape to a height of 4mm Page 1 of 5
2 Use Sketch Circle tool to draw a circle 45mm diameter Click on the shape and select the Move handle use the arrow to drag the shape to the edge of the circle and then if necessary rotate it to the best position for using the pattern tool the video explains why this is important. Select Pattern Circular Pattern Click on Solid and select the shape. Then click on Axis and select the circle. The box comes up showing number of copies of the shape. Increase the copies until the shapes intersect If you are having trouble selecting the shape properly, the video gives tips on this. Page 2 of 5
3 Selecting Grouping tool (or just do Ctrl G on your keyboard), then select each shape in turn until you have selected them all, then press Enter. If you click on the shape now you will see that all the shapes select as one group Now you will scale your design to the size you want: - Draw a square the size you want the decoration to be e.g. 65mm square. - Click on the drawing, select Move handle and move it over the square ready to scale it down. Select the Scale tool and either use the arrow to adjust the size or type a factor in the number box, e.g. 0.6 (scaled to a factor of 0.6 of the original size). When the size is correct, left click to finish. Page 3 of 5
4 Select Construct Extrude and select the centre shape ensure it is set to extrude Merge on the drop down. Select Sketch Polygon and click in the centre of the design to draw a shape which will form the centre part of the LED decoration. Here a triangle is being used, so put 3 in box for number of sides. You could use any shape, but it must intersect with the outer ring of the design to form a single 3D printed product. Here is the centre triangle see how the corners intersect the outer shape Put the height in the box remember the outer ring is 4mm high here 5mm is used so the centre sits 1mm higher than the rest of the decoration. Now you need to cut the hole for the LED light first check the hole size needed for your lights. Here we are making a 10mm diameter hole. Use Primitives Cylinder tool to make a cylinder of 10mm diameter put radius in box, leave the height at the default value of 20mm. Use the Snap tool to snap the cylinder to the centre of the shape ready to cut the hole. Page 4 of 5
5 Select Construct Extrude and click on the top face of the cylinder and push it through the decoration to make the hole. Press Enter to finish. If you wish you can add some features to your LED decoration. Here small cylinders were used to make holes in the points of the triangle. The edges of the triangles were bevelled using Modify Chamfer. Small triangles were made and snapped onto the decoration and moved into place. Click the drop down on the top left of your screen and select Export STL It will ask if you want to combine all objects into one say YES. Save your file. Page 5 of 5
CAD tutorial for the drinking straw support
CAD tutorial for the drinking straw support Having tried a number of different designs, this one worked best on the greatest variety of glasses straight sided glass, angled glass and even a champagne flute.
More informationCube in a cube Fusion 360 tutorial
Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.
More informationStraw support Fusion 360
Straw support Fusion 360 Before using these instructions, watch the video screencast of the CAD drawing actually being done in the software. Click this link for video tutorial This design works on a variety
More informationIntroduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software
Introduction to 3D Printing Activity 1: Design a keychain using computer-aided design software 1 In this activity we ll design a keychain name tag and learn the fundamentals of computer-aided design, the
More informationVan Assembly. Creating an Assembly. Original by Steven Jaffe Modified by E. Brunelle 2/07 1
Van Assembly Creating an Assembly 1 Part One the Axle 1. Set Units to Inches 2. Create a New Design. 3. Save the Design as axleinl_cad1_1 in your Van folder. 4. Create a New Sketch on the Lateral workplane.
More information1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry
2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply
More informationSolidWorks Tutorial 1. Axis
SolidWorks Tutorial 1 Axis Axis This first exercise provides an introduction to SolidWorks software. First, we will design and draw a simple part: an axis with different diameters. You will learn how to
More information1. Change units to inches: Tools > Options > Document Properties > Units and then select: IPS (inch, pound, second)
Steps to Draw Pump Impeller: The steps below show one way to draw the impeller. You should make sure that your impeller is not larger than the one shown or it may not fit in the pump housing. 1. Change
More informationSolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
More informationModule 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge
Inventor (10) Module 1G: 1G- 1 Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge In Module 1A, we have explored
More informationLesson 6 2D Sketch Panel Tools
Lesson 6 2D Sketch Panel Tools Inventor s Sketch Tool Bar contains tools for creating the basic geometry to create features and parts. On the surface, the Geometry tools look fairly standard: line, circle,
More informationIntroduction to ANSYS DesignModeler
Lecture 4 Planes and Sketches 14. 5 Release Introduction to ANSYS DesignModeler 2012 ANSYS, Inc. November 20, 2012 1 Release 14.5 Preprocessing Workflow Geometry Creation OR Geometry Import Geometry Operations
More informationCreo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
More informationFrom the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select
Chapter 5 In sweep command there is a) Two sketch profiles b) Two path c) One sketch profile and one path The sweep profile is used to create threads springs circular things and difficult geometry. For
More informationNut and Bolt Tutorial
Thread Representations Nut and Bolt Tutorial Parts to a Thread Thread Dimensioning Major Diameter Thread Series (IE UNC, UNF, ACME, etc) ½ - 13 UNC 2 A or B A = External B = Internal Threads per Inch Class
More informationAdvanced Modeling Techniques Sweep and Helical Sweep
Advanced Modeling Techniques Sweep and Helical Sweep Sweep A sweep is a profile that follows a path placed on a datum. It is important when creating a sweep that the designer plans the size of the path
More informationSolidworks Tutorial Pencil
The following instructions will be used to help you create a Pencil using Solidworks. These instructions are ordered to make the process as simple as possible. Deviating from the order, or not following
More informationModule 1H: Creating an Ellipse-Based Cylindrical Sheet-metal Lateral Piece
Inventor (10) Module 1H: 1H- 1 Module 1H: Creating an Ellipse-Based Cylindrical Sheet-metal Lateral Piece In this Module, we will learn how to create an ellipse-based cylindrical sheetmetal lateral piece
More informationSash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1.
Sash Clamp 1 Introduction: The Sash clamp consists of nine parts. In creating the clamp we will be looking at the improvements made by SolidWorks in linear patterns, adding threads and in assembling the
More informationPart 8: The Front Cover
Part 8: The Front Cover 4 Earpiece cuts and housing Lens cut and housing Microphone cut and housing The front cover is similar to the back cover in that it is a shelled protrusion with screw posts extruding
More informationPart 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion.
Part 2: Earpiece 4 Round extrusion Radial pattern Chamfered edge To create this part, you'll use some of the same extrusion techniques you used in the lens part. The only difference in this part is that
More informationThe Revolve Feature and Assembly Modeling
The Revolve Feature and Assembly Modeling PTC Clock Page 52 PTC Contents Introduction... 54 The Revolve Feature... 55 Creating a revolved feature...57 Creating face details... 58 Using Text... 61 Assembling
More informationEngineering Innovation Center Autodesk Fusion 360
Engineering Innovation Center Autodesk Fusion 360 Introduction The Engineering Innovation Center is a large academic maker space with plenty of tools and equipment. In order to use these items you must
More information1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry
4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are
More informationJ. La Favre Fusion 360 Lesson 2 April 19, 2017
In this lesson, you will create a round plate with 12 counter-bored holes to fit 6-32 socket head screws. A counter-bored hole has two diameters, one to fit the threaded part of the screw and the other
More informationBottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
More informationAlternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
More informationCreo Extrude Tutorial 3: Hole, Fillets and Rounds
Creo Extrude Tutorial 3: Hole, Fillets and Rounds By: Matthew Jourden Brighton High School 1. Open Creo Parametric 2. File > Open > extrudetutorial (From Creo Extrude Tutorial 1) NOTE: Minimum of 2 other
More informationChair. Bottom Rail. on the Command Manager. on the Weldments toolbar.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
More informationModeling Basic Mechanical Components #1 Tie-Wrap Clip
Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely
More informationChapter 2. Drawing Sketches for Solid Models. Learning Objectives
Chapter 2 Drawing Sketches for Solid Models Learning Objectives After completing this chapter, you will be able to: Start a new template file to draw sketches. Set up the sketching environment. Use various
More informationTable of Contents. Lesson 1 Getting Started
NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard
More informationIntroduction to Autodesk Inventor User Interface Student Manual MODEL WINDOW
Emmett Wemp EDTECH 503 Introduction to Autodesk Inventor User Interface Fill in the blanks of the different tools available in the user interface of Autodesk Inventor as your instructor discusses them.
More informationInventor-Parts-Tutorial By: Dor Ashur
Inventor-Parts-Tutorial By: Dor Ashur For Assignment: http://www.maelabs.ucsd.edu/mae3/assignments/cad/inventor_parts.pdf Open Autodesk Inventor: Start-> All Programs -> Autodesk -> Autodesk Inventor 2010
More informationMAKING THE FAN HOUSING
Our goal is to make the following part: 39-245 RAPID PROTOTYPE DESIGN CARNEGIE MELLON UNIVERSITY SPRING 2007 MAKING THE FAN HOUSING This part is made up of two plates joined by a cylinder with holes in
More informationAutoCAD LT 2012 Tutorial. Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS. Schroff Development Corporation
AutoCAD LT 2012 Tutorial Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation AutoCAD LT 2012 Tutorial 1-1 Lesson 1 Geometric Construction
More informationThere are two types of cove light in terms of light distribution inside a room
DIALux evo Tutorials Tutorial 2 How to create a cove light detail In this tutorial you will learn the following commands. 1. Using help lines 2. Using ceiling. 3. Using cutout 4. Using Boolean operation
More informationUsing Siemens NX 11 Software. Sheet Metal Design - Casing
Using Siemens NX 11 Software Sheet Metal Design - Casing Based on a YouTube NX tutorial 1. 1 https://www.youtube.com/watch?v=-siyi1vz87k A&M CAD in mechanical engineering 1 1 Introduction. Start NX 11
More informationInventor Activity 5: Lofted Vase
Inventor Activity 5: Lofted Vase In this tutorial, you will use a few new commands to create a free form Lofted object. Sometimes you want to create an object that is not made up of square, flat, or perfectly
More informationAutoCAD 2D. Table of Contents. Lesson 1 Getting Started
AutoCAD 2D Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard
More informationHydro Hull. Chapter 21. Boat. A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2).
Chapter 21 Boat Hydro Hull A. Save as "HYDRO". Step 1. Open your HULL MID PLANE file (Chapter 2). Step 2. Click File Menu > Save As. Step 3. Key-in HYDRO for the filename and press ENTER. B. Delete Loft1,
More informationSolidWorks Design & Technology
SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one
More informationIntroduction to CATIA V5
Introduction to CATIA V5 Release 17 (A Hands-On Tutorial Approach) Kirstie Plantenberg University of Detroit Mercy SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower
More informationIntroduction to 3D CAD with SolidWorks. Jianan Li
Introduction to 3D CAD with SolidWorks Jianan Li Create a New Part The first time you launch SolidWorks, it asks you to set the default units and dimension standard. Make sure you have IPS and ANSI selected,
More informationBuilding a Greek pool. This lesson will continue with the push/pull and off set tools. You will also be using exact measurements and changing the
Building a Greek pool. This lesson will continue with the push/pull and off set tools. You will also be using exact measurements and changing the sides of a polygon. A new tool will be introduced called
More informationAutodesk Inventor 2016 Creating Sketches
Autodesk Inventor 2016 Creating Sketches 2D Sketch Practice 1 1. Launch Autodesk Inventor 2016 2. Create a new Part file (.ipt) 3. Save File As a. Click on the save icon. b. Save you file onto your flash
More informationIntroduction to SolidWorks Introduction to SolidWorks
Introduction to SolidWorks Introduction to SolidWorks SolidWorks is a powerful 3D modeling program. The models it produces can be used in a number of ways to simulate the behaviour of a real part or assembly
More informationBasic 2D drawing skills in AutoCAD 2017
Basic 2D drawing skills in AutoCAD 2017 This Tutorial is going to teach you the basic functions of AutoCAD and make you more efficient with the program. Follow all the steps so you can learn all the skills.
More informationPart Design Fundamentals
Part Design Fundamentals 1 Course Presentation Objectives of the course In this course you will learn basic methods to create and modify solids features and parts Targeted audience New CATIA V5 Users 1
More informationBuild the clerestory of Chartres Cathedral
Build the clerestory of Chartres Cathedral Overview: Step 1. Create a new Design Layer Step 2. Build the wall Step 3. Build the lancets Step 4. Build the rose window Step 5. Build the rose window quatrefoils
More informationDesignSpark Mechanical. Guidebook
DesignSpark Mechanical Guidebook 1 Chapter 5 Introduction and Installation and the User Interface of DesignSpark Mechanical 5-1 Introduction of DesignSpark Mechanical DesignSpark Mechanical (DSM in short)
More informationwith MultiMedia CD Randy H. Shih Jack Zecher SDC PUBLICATIONS Schroff Development Corporation
with MultiMedia CD Randy H. Shih Jack Zecher SDC PUBLICATIONS Schroff Development Corporation WWW.SCHROFF.COM Lesson 1 Geometric Construction Basics AutoCAD LT 2002 Tutorial 1-1 1-2 AutoCAD LT 2002 Tutorial
More informationCreate A Mug. Skills Learned. Settings Sketching 3-D Features. Revolve Offset Plane Sweep Fillet Decal* Offset Arc
Create A Mug Skills Learned Settings Sketching 3-D Features Slice Line Tool Offset Arc Revolve Offset Plane Sweep Fillet Decal* Tutorial: Creating A Custom Mug There are somethings in this world that have
More informationHOW TO CREATE A SUPER SHINY PENCIL ICON
HOW TO CREATE A SUPER SHINY PENCIL ICON Tutorial from http://psd.tutsplus.com/ Compiled by INTRODUCTION The Pencil is one of the visual metaphors most used to express creativity. In this tutorial,
More informationVeerapandian.K Mechanical Engg Vedharanyam A manual to mechanical designers How Solid works Works?
Compiled by Veerapandian.K Mechanical Engg Vedharanyam-614 810 A manual to mechanical designers How Solid works Works? Solid works Overview Solid works main idea is user to create drawing directly in 3D
More informationSTEP BY STEP GUIDE FOR CREATING A CUBE IN FREECAD. STEP 1. Chose Create a new Empty Document Part Design Create a New Sketch XY- Plane and click OK.
STEP BY STEP GUIDE FOR CREATING A CUBE IN FREECAD STEP 1. Chose Create a new Empty Document Part Design Create a New Sketch XY- Plane and click OK. STEP 2. Chose Rectangle tool and create any rectangle
More informationCAD Tutorial 24: Step by Step Guide
CAD TUTORIAL 24: Step by step CAD Tutorial 24: Step by Step Guide Level of Difficulty Time Approximately 40 50 minutes Lesson Objectives To understand the basic tools used in SketchUp. To understand the
More informationEngineering Technology
Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,
More informationRotational Patterns of Sketched Features Using Datum Planes On-The-Fly
Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly Patterning a sketched feature (such as a slot, rib, square, etc.,) requires a slightly different technique. Why can t we create a
More informationPrinciples and Applications of Microfluidic Devices AutoCAD Design Lab - COMSOL import ready
Principles and Applications of Microfluidic Devices AutoCAD Design Lab - COMSOL import ready Part I. Introduction AutoCAD is a computer drawing package that can allow you to define physical structures
More informationAutoCAD Tutorial First Level. 2D Fundamentals. Randy H. Shih SDC. Better Textbooks. Lower Prices.
AutoCAD 2018 Tutorial First Level 2D Fundamentals Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to
More informationIntroduction to Circular Pattern Flower Pot
Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,
More informationAlibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1
Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Part Tutorial Exercise 5: Loft-Tube-1 [Complete] In this Exercise, We will set System Parameters first, then part options. Then, in sketch
More informationAutoCAD LT 2009 Tutorial
AutoCAD LT 2009 Tutorial Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better Textbooks. Lower Prices. AutoCAD LT 2009 Tutorial 1-1 Lesson
More informationg. Click once on the left vertical line of the rectangle.
This drawing will require you to a model of a truck as a Solidworks Part. Please be sure to read the directions carefully before constructing the truck in Solidworks. Before submitting you will be required
More informationMODELING AND DESIGN C H A P T E R F O U R
MODELING AND DESIGN C H A P T E R F O U R OBJECTIVES 1. Identify and specify basic geometric elements and primitive shapes. 2. Select a 2D profile that best describes the shape of an object. 3. Identify
More informationSketchUp Training Notes By Professional CAD Systems Ltd Ph
SketchUp Training Notes By Professional CAD Systems Ltd Ph 07 847 2268 Coffee Table: Using the Rectangle tool, draw a rectangle which is 1100mmx550mm to form the Top of the coffee table. You will need
More informationHow to draw the CB South Kerf Bent Clock:
How to draw the CB South Kerf Bent Clock: Open sketch up, use the Product Design and Woodworking template with Inches as the units. If there is a person in the drawing space, you can delete him/her. When
More informationGetting Started. Right click on Lateral Workplane. Left Click on New Sketch
Getting Started 1. Open up PTC Pro/Desktop by either double clicking the icon or through the Start button and in Programs. 2. Once Pro/Desktop is open select File > New > Design 3. Close the Pallet window
More informationCreating a light studio
Creating a light studio Chapter 5, Let there be Lights, has tried to show how the different light objects you create in Cinema 4D should be based on lighting setups and techniques that are used in real-world
More informationSDC. AutoCAD LT 2007 Tutorial. Randy H. Shih. Schroff Development Corporation Oregon Institute of Technology
AutoCAD LT 2007 Tutorial Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com AutoCAD LT 2007 Tutorial 1-1 Lesson 1 Geometric
More informationStarting a 3D Modeling Part File
1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce
More informationJ. La Favre Fusion 360 Lesson 4 April 21, 2017
In this lesson, you will create an I-beam like the one in the image to the left. As you become more experienced in using CAD software, you will learn that there is usually more than one way to make a 3-D
More informationLab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008
1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical
More informationCOURSE: INTRODUCTION TO CAD GRADES: UNIT: Measurement
UNIT: Measurement - Students will demonstrate correctness in measuring using various scales and instruments. Demonstrate the various marks that make up a ruler including 1/16, 1/8, ¼ and ½. Assessment
More informationDigital Camera Exercise
Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document
More informationCREO.1 MODELING A BELT WHEEL
CREO.1 MODELING A BELT WHEEL Figure 1: A belt wheel modeled in this exercise. Learning Targets In this exercise you will learn: Using symmetry when sketching Using pattern to copy features Using RMB when
More informationWelding Letters to a Shape in Inkscape By Carrie Schwartz Carrie s Creations
Welding Letters to a Shape in Inkscape By Carrie Schwartz Carrie s Creations Once you learn some basic steps welding letters to a shape is really an easy task that you can use over and over again in creating
More information< Then click on this icon on the vertical tool bar that pops up on the left side.
Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts
More informationLesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
More informationSolidWorks Navigation
SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length
More informationSolidWorks & Tinkerine 3D Printing Tutorial ELEC391
SolidWorks & Tinkerine 3D Printing Tutorial ELEC391 Engineering Services, Dept. of Electrical and Computer Engineering University of British Columbia, Faculty of Applied Science Table of Contents Installing
More informationMade Easy. Jason Pancoast Engineering Manager
3D Sketching Made Easy Jason Pancoast Engineering Manager Today I have taught you to sketch in 3D. It s as easy as counting ONE, TWO, FIVE...er...THREE! When your sketch only lives in Y and in X, Adding
More informationWelcome to Corel DESIGNER, a comprehensive vector-based package for technical graphic users and technical illustrators.
Workspace tour Welcome to Corel DESIGNER, a comprehensive vector-based package for technical graphic users and technical illustrators. This tutorial will help you become familiar with the terminology and
More informationLABORATORY MANUAL COMPUTER AIDED DESIGN LAB
LABORATORY MANUAL COMPUTER AIDED DESIGN LAB Sr. No 1 2 3 Experiment Title Setting up of drawing environment by setting drawing limits, drawing units, naming the drawing, naming layers, setting line types
More informationBasic Features. In this lesson you will learn how to create basic CATIA features. Lesson Contents: CATIA V5 Fundamentals- Lesson 3: Basic Features
Basic Features In this lesson you will learn how to create basic CATIA features. Lesson Contents: Case Study: Basic Features Design Intent Stages in the Process Determine a Suitable Base Feature Create
More informationPro/DESKTOP Tutorial Drafting Bow Compass
Pro/DESKTOP Tutorial Drafting Bow Compass Michael Flowers 2005 1 Objectives: To develop confidence with the Pro/DESKTOP software. To learn to utilize extrude, project, revolve, round, and chamfer features.
More informationModule 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece
1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a
More informationAutodesk Inventor. In Engineering Design & Drafting. By Edward Locke
Autodesk Inventor In Engineering Design & Drafting By Edward Locke Engineering Design Drafting Essentials Working Drawings: Orthographic Projection Views (multi-view, auxiliary view, details and sections)
More informationAssembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:
MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing
More informationSketch-Up Guide for Woodworkers
W Enjoy this selection from Sketch-Up Guide for Woodworkers In just seconds, you can enjoy this ebook of Sketch-Up Guide for Woodworkers. SketchUp Guide for BUY NOW! Google See how our magazine makes you
More informationCreo Parametric Primer
PTC Creo Parametric - Primer Student and Academic Editions 02 Helpful hints are enclosed in red brackets or round bubbles like this one! Creo Parametric Primer THIS VERSION OF THE CREO PRIMER HAS BEEN
More informationLAB 1A: Intro to SolidWorks: 2D -> 3D Brackets
LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets Set units Create Sketch Add relations Linear patterns Mirror Fillet Extrude Extrude cut First, set units. click Option on top of main menu Open Document Properties
More informationSpatula. Spatula SW 2015 Design & Communication Graphics Page 1
Spatula Introduction: The model shown in the picture is made of three parts, - the base, the washer and the handle. The base requires the use of Spline and Style Spline command, Slot command and Mirror
More informationCAD-CAM-CAE Examples
CAD-CAM-CAE Examples example title: example number: example level: CAx system: Related material part with TÁMOP Job Description: Shaft type component (CAD) ÓE-A06a basic - medium - advanced CATIA v5 CAD
More informationConquering the Rubicon
Autodesk Inventor R10 Fundamentals: Conquering the Rubicon Elise Moss SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Schroff Development Corporation P.O. Box 1334
More information