Engineering Innovation Center Fabrication Shop Basic CAD Training
|
|
|
- Deborah Kelly
- 5 years ago
- Views:
Transcription
1 Engineering Innovation Center Fabrication Shop Basic CAD Training
2 Introduction The Engineering Innovation Center Fabrication Shop was established for support of undergraduate student course work. Every effort will be made to make the shop available for these projects. Students of Engineering who desire to use this equipment for educationally-related activities are required to attend training. 8/30/2016 Engineering Innovation Center 2
3 Overview All images and instructions pertain to SolidWorks 2015 Creation of part Fully defined sketches Extrusions Features Drawing Dimensions Hole Callouts Section Views Expectations for Fabrication 8/30/2016 Engineering Innovation Center 3
4 Begin Start up SolidWorks Start a new Part File Make sure you are working in Inches In the bottom right-hand corner it should say IPS If not click on MMGS and change it to IPS Alternatively you can go to Options>Document Properties>Units and select IPS 8/30/2016 Engineering Innovation Center 4
5 Navigation Rotation, orbiting, panning and general movement can be controlled by the mouse in combination with the keyboard To pan simply hold control and middle click To orbit hold middle click and move the mouse To see standard views press spacebar and select a view If at any time your model disappears press f to fit the model to the workspace 8/30/2016 Engineering Innovation Center 5
6 Sketches The basis for any part Should always be fully defined before moving on Should be referenced to origin Relations/Constraints further define sketch geometry Under Defined Sketch Fully Defined Sketch 8/30/2016 Engineering Innovation Center 6
7 Create a Sketch Start a Sketch Pick a plane Start at origin 8/30/2016 Engineering Innovation Center 7
8 Dimension/Constrain Dimensions and constraints define sketches Use the Smart Dimension tool to Define length, angle, radius or diameter. Relations/Constraints further define sketches Note: To constrain multiple entities hold control as you select them 8/30/2016 Engineering Innovation Center 8
9 Replicate This Sketch Construction lines are not crucial Make sure fully defined before moving on If not fully defined check relationship to origin or relations between lines To change between units click on IPS or MMGS in bottom right-hand corner 8/30/2016 Engineering Innovation Center 9
10 Extrude Extrusions make a 2D sketch into a 3D model Select the extrude command Pick sketch profile and extrude to inches 8/30/2016 Engineering Innovation Center 10
11 Design Tree Organization Organization helps with future editing or modifying of features Good CAD practice is to descriptively rename everything To rename a feature simply double click on it in the design tree Here the extrusion has been renamed MainBody This will allow anyone collaborating on the design to easily recognize which operation was used to create the part 8/30/2016 Engineering Innovation Center 11
12 Hole Wizard Allows you to create: Slots Counterbores/Countersinks Threaded(Tapped) Holes Complex Holes Tapered Tap Holes Hole locations easily defined by sketches Allows hole callouts within drawings to be done with one click 8/30/2016 Engineering Innovation Center 12
13 Sketch Defined Hole Locations Start a sketch on this plane Dimension sketch points to define hole locations Note: Points have been constrained to be horizontal/vertical 8/30/2016 Engineering Innovation Center 13
14 Hole Wizard Parameters Start the Hole Wizard Select Positions The Position operation will require a plane or face to start the hole at Select the plane that we sketched on If your sketch is not visible right click on it in the design tree within the workspace and make it visible 8/30/2016 Engineering Innovation Center 14
15 Placing Holes Its as easy as point and click Simply pick each of the sketch points previously defined At this point and time the holes might not look how you want them. Switch back over to the type tab on the left hand side Notice the sketch points are black indicating that the hole locations are fully defined 8/30/2016 Engineering Innovation Center 15
16 Hole Definition The holes on this particular part are classified as #8-32 UNC This means that the holes will be tapped or threaded Select the Straight Tapped Hole Using the drop downs select the specified thread classification End conditions can be modified under the End Condition tab Set end condition to Through All 8/30/2016 Engineering Innovation Center 16
17 Center Holes Replicate this sketch of two points on the uppermost surface of the solid Dimension them to be.325in apart Check if fully defined If not fully defined constrain the left point to the origin and both points to be parallel 8/30/2016 Engineering Innovation Center 17
18 Center Holes Now, using HoleWizard, create a #8-32 tapped hole that extends thru all 8/30/2016 Engineering Innovation Center 18
19 Center Holes (Reamed) In a similar fashion create a straight hole that is reamed to.2495in This is accomplished by selecting the hole function. Then, using standard drill sizes, select 1/4in and check the show custom sizing box 8/30/2016 Engineering Innovation Center 19
20 Circular Pattern To make creating a circular pattern easier we will turn on axes Click the glasses dropdown at the top of the workspace Select the view temporary axes icon Hover mouse over options to see what they are Click the linear pattern dropdown under the feature tab Select Circular Pattern 8/30/2016 Engineering Innovation Center 20
21 Circular Pattern Parameters We are going to create a circular pattern of the center #8-32 tapped hole We have already defined the radius of the pattern in the starting sketch Under the Features and Faces make sure the #8-32 hole is selected In the first box you need an axis or circular feature to revolve around Select the axis of the reamed hole Make sure the equal spacing check box is selected Set the pattern amount to 3 8/30/2016 Engineering Innovation Center 21
22 Result This is the finished model ready to be inserted into a mechanical drawing 8/30/2016 Engineering Innovation Center 22
23 Drawings Drawings allow you to communicate the features of your model to: The public Machinists Investors Anyone After creating your model select the new dropdown and click create new drawing from part/assembly Always use A(ANSI) landscape 8/30/2016 Engineering Innovation Center 23
24 Placing Views Paste views into the drawing workspace by clicking and dragging them from the right-hand side Arrange a descriptive view as the parent model view Drag and click to any side to place projected views 8/30/2016 Engineering Innovation Center 24
25 Arranging Views Arrange views by dragging Placed views will move according to the parent view with the exception of isometric views Scale can be adjusted on the left-hand side while a view is selected Views should be arranged in an esthetically pleasing way Delete the initial hole callouts in order to place more descriptive ones Dimensions and annotations can be added in a similar fashion to dimensions in the modeling environment Within the drawing using the dimension tool will not change the dimension but rather display the previously defined dimension 8/30/2016 Engineering Innovation Center 25
26 Drawing Practices Even if you prefer to model in millimeters/centimeters always complete drawings in inches Place dimensions between views as much as possible Avoid crossing lines Pick a reference edge and try to stick to it Include all needed dimensions Your part should be able to be created without the need for a solid model (using just the drawing) 8/30/2016 Engineering Innovation Center 26
27 Title Block The title block is all of the information in the lower portion of the page Title block can be edited by right clicking on white space and selecting edit sheet format Drawing number should not be part description, it should include information for reference eg. (ENGR112_01) Your name goes on the uppermost line above drawing title Material, Finish and Tolerances are crucial pieces of information DO NOT FORGET THEM! When finished editing the title block return to the drawing view by clicking the icon in the top right-hand corner of the workspace 8/30/2016 Engineering Innovation Center 27
28 Practice Recreate this drawing 8/30/2016 Engineering Innovation Center 28
29 Extra Resources Solidworks rrpzwfw Autodesk /30/2016 Engineering Innovation Center 29
30 Conclusion Unsafe practice or obvious abuse of equipment constitutes a danger to people and damages equipment. Therefore the Fabrication Shop Manager or any person observing an unsafe act should stop unsafe practices in the Fabrication Shop. Students violating any of these rules will have their Fabrication Shop privileges revoked for a period of at least two weeks. Longer periods may be assessed, depending upon the judgment of the Fabrication Shop Manager and the Engineering Innovation Center Facility Manager. 8/30/2016 Engineering Innovation Center 30
Engineering Innovation Center Fabrication Shop Basic CAD Training
Engineering Innovation Center Fabrication Shop Basic CAD Training Introduction The Engineering Innovation Center Fabrication Shop was established for support of undergraduate student course work. Every
DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY
DEPARTMENT OF MECHANICAL AND INDUSTRIAL ENGINEERING NORTHEASTERN UNIVERSITY CAPSULE PROGRAM Funded by NSF grant #0833636 Tutorial 02 3D Part Modeling SolidWorks 2010 Copyright 2010 Prof. Zeid 3D Part Modeling
Engineering Innovation Center Autodesk Fusion 360
Engineering Innovation Center Autodesk Fusion 360 Introduction The Engineering Innovation Center is a large academic maker space with plenty of tools and equipment. In order to use these items you must
Shaft Hanger - SolidWorks
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric
SolidWorks Navigation
SolidWorks Basics SolidWorks Navigation Command Bar Feature Tree Model Window Simple Box Select the Front plane Create a new sketch Create a Center Rectangle from the origin Smart Dimension the length
Inventor-Parts-Tutorial By: Dor Ashur
Inventor-Parts-Tutorial By: Dor Ashur For Assignment: http://www.maelabs.ucsd.edu/mae3/assignments/cad/inventor_parts.pdf Open Autodesk Inventor: Start-> All Programs -> Autodesk -> Autodesk Inventor 2010
Toothbrush Holder. A drawing of the sheet metal part will also be created.
Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson; Sketch (Line, Centerline, Circle, Add Relations, Smart Dimension,), Extrude Boss/Base, and Edit
Lesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
Engineering Technology
Engineering Technology Introduction to Parametric Modelling Engineering Technology 1 See Saw Exercise Part 1 Base Commands used New Part This lesson includes Sketching, Extruded Boss/Base, Hole Wizard,
Foreword. If you have any questions about these tutorials, drop your mail to
Foreword The main objective of these tutorials is to give you a kick start using Solidworks. The approach to write this tutorial is based on what is the most important knowledge you should know and what
SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
Assembly Receiver/Hitch/Ball/Pin to use for CAD LAB 5A and 5B:
MECH 130 CAD LAB 5 SPRING 2017 due Friday, April 21, 2016 at 4:30 PM All of LAB 5 s hardcopies will be working drawing layouts. Do not print out from the part file. We will be using the ME130DRAW drawing
ME Week 2 Project 2 Flange Manifold Part
1 Project 2 - Flange Manifold Part 1.1 Instructions This project focuses on additional sketching methods and sketching commands. Revolve and Work features are also introduced. The part being modeled is
Name: Date Completed: Basic Inventor Skills I
Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.
Introduction to 3D Printing. Activity 1: Design a keychain using computer-aided design software
Introduction to 3D Printing Activity 1: Design a keychain using computer-aided design software 1 In this activity we ll design a keychain name tag and learn the fundamentals of computer-aided design, the
Feature-Based Modeling and Optional Advanced Modeling. ENGR 1182 SolidWorks 05
Feature-Based Modeling and Optional Advanced Modeling ENGR 1182 SolidWorks 05 Today s Objectives Feature-Based Modeling (comprised of 2 sections as shown below) 1. Breaking it down into features Creating
Activity Sketch Plane Cube
Activity 1.5.4 Sketch Plane Cube Introduction Have you ever tried to explain to someone what you knew, and that person wanted you to tell him or her more? Here is your chance to do just that. You have
SolidWorks Design & Technology
SolidWorks Design & Technology Training Course at PHSG Ex 5. Lego man Working with part files 8mm At first glance the Lego man looks complicated but I hope you will see that if you approach a project one
Nut and Bolt Tutorial
Thread Representations Nut and Bolt Tutorial Parts to a Thread Thread Dimensioning Major Diameter Thread Series (IE UNC, UNF, ACME, etc) ½ - 13 UNC 2 A or B A = External B = Internal Threads per Inch Class
Veerapandian.K Mechanical Engg Vedharanyam A manual to mechanical designers How Solid works Works?
Compiled by Veerapandian.K Mechanical Engg Vedharanyam-614 810 A manual to mechanical designers How Solid works Works? Solid works Overview Solid works main idea is user to create drawing directly in 3D
Solid Part Four A Bracket Made by Mirroring
C h a p t e r 5 Solid Part Four A Bracket Made by Mirroring This chapter will cover the following to World Class standards: Sketch of a Solid Problem Draw a Series of Lines Finish the 2D Sketch Extrude
Starting a 3D Modeling Part File
1 How to Create a 3D Model and Corresponding 2D Drawing with Dimensions, GDT (Geometric Dimensioning and Tolerance) Symbols and Title Block in SolidWorks 2013-2014 By Edward Locke This tutorial will introduce
2809 CAD TRAINING: Part 1 Sketching and Making 3D Parts. Contents
Contents Getting Started... 2 Lesson 1:... 3 Lesson 2:... 13 Lesson 3:... 19 Lesson 4:... 23 Lesson 5:... 25 Final Project:... 28 Getting Started Get Autodesk Inventor Go to http://students.autodesk.com/
1. Open the Feature Modeling demo part file on the EEIC website. Ask student about which constraints needed to Fully Define.
BLUE boxed notes are intended as aids to the lecturer RED boxed notes are comments that the lecturer could make Control + Click HERE to view enlarged IMAGE and Construction Strategy he following set of
SolidWorks Training. Introductory course for staff and students from the School of Physics and Astronomy
SolidWorks Training Introductory course for staff and students from the School of Physics and Astronomy i) Introductory presentation SolidWorks Training ii) The SolidWorks GUI The SolidWorks Graphical
The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly.
Introduction - Teacher Notes Fig 1. The project focuses on the design for a Pencil holder, but could be adapted to any simple assembly. Pro/DESKTOP enables pupils (and teachers) to communicate and model
AEROPLANE. Create a New Folder in your chosen location called Aeroplane. The four parts that make up the project will be saved here.
AEROPLANE Prerequisite Knowledge Previous knowledge of the following commands is required to complete this lesson. Sketching (Line, Rectangle, Arc, Add Relations, Dimensioning), Extrude, Assemblies and
Introduction to Circular Pattern Flower Pot
Prerequisite Knowledge Previous knowledge of the sketching commands Line, Circle, Add Relations, Smart Dimension is required to complete this lesson. Previous examples of Revolved Boss/Base, Cut Extrude,
Lab 3 Introduction to SolidWorks I Silas Bernardoni 10/9/2008
1 Introduction This lab is designed to provide you with basic skills when using the 3D modeling program SolidWorks. You will learn how to build parts, assemblies and drawings. You will be given a physical
Introduction to Autodesk Inventor for F1 in Schools (Australian Version)
Introduction to Autodesk Inventor for F1 in Schools (Australian Version) F1 in Schools race car In this course you will be introduced to Autodesk Inventor, which is the centerpiece of Autodesk s Digital
From the above fig. After sketching the path and profile select the sweep command First select the profile from property manager tree And then select
Chapter 5 In sweep command there is a) Two sketch profiles b) Two path c) One sketch profile and one path The sweep profile is used to create threads springs circular things and difficult geometry. For
Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
Beginner s Guide to SolidWorks Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS
Beginner s Guide to SolidWorks 2008 Alejandro Reyes, MSME Certified SolidWorks Professional and Instructor SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com Part Modeling
Engineering & Computer Graphics Workbook Using SOLIDWORKS
Engineering & Computer Graphics Workbook Using SOLIDWORKS 2017 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
Modeling Basic Mechanical Components #1 Tie-Wrap Clip
Modeling Basic Mechanical Components #1 Tie-Wrap Clip This tutorial is about modeling simple and basic mechanical components with 3D Mechanical CAD programs, specifically one called Alibre Xpress, a freely
AutoDesk Inventor: Creating Working Drawings
AutoDesk Inventor: Creating Working Drawings Inventor allows you to quickly and easily make quality working drawings from your 3D models. This tutorial will walk you through the steps in creating a working
for Solidworks TRAINING GUIDE LESSON-9-CAD
for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working
Drawing and Assembling
Youth Explore Trades Skills Description In this activity the six sides of a die will be drawn and then assembled together. The intent is to understand how constraints are used to lock individual parts
1. Create a 2D sketch 2. Create geometry in a sketch 3. Use constraints to position geometry 4. Use dimensions to set the size of geometry
2.1: Sketching Many features that you create in Fusion 360 start with a 2D sketch. In order to create intelligent and predictable designs, a good understanding of how to create sketches and how to apply
The Revolve Feature and Assembly Modeling
The Revolve Feature and Assembly Modeling PTC Clock Page 52 PTC Contents Introduction... 54 The Revolve Feature... 55 Creating a revolved feature...57 Creating face details... 58 Using Text... 61 Assembling
Engineering & Computer Graphics Workbook Using SolidWorks 2014
Engineering & Computer Graphics Workbook Using SolidWorks 2014 Ronald E. Barr Thomas J. Krueger Davor Juricic SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org)
Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
Introduction to solid modeling using Onshape
Onshape is a CAD/solid modeling application. It provides powerful parametric and direct modeling capabilities. It is cloud based therefore you do not need to install any software. Documents are shareable.
When you complete this assignment you will:
Objjectiives When you complete this assignment you will: 1. sketch and create models using new work planes and the loft command. 2. sketch and create models using the revolve command. 3. sketch and dimension
Table of Contents. Lesson 1 Getting Started
NX Lesson 1 Getting Started Pre-reqs/Technical Skills Basic computer use Expectations Read lesson material Implement steps in software while reading through lesson material Complete quiz on Blackboard
Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)
Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model
An Introduction to Autodesk Inventor 2011 and AutoCAD Randy H. Shih SDC PUBLICATIONS. Schroff Development Corporation
An Introduction to Autodesk Inventor 2011 and AutoCAD 2011 Randy H. Shih SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation An Introduction to Autodesk Inventor 2011 and AutoCAD 2011
Autodesk Inventor. In Engineering Design & Drafting. By Edward Locke
Autodesk Inventor In Engineering Design & Drafting By Edward Locke Engineering Design Drafting Essentials Working Drawings: Orthographic Projection Views (multi-view, auxiliary view, details and sections)
SolidWorks Reference Geometry
SolidWorks Reference Geometry IDeATe Laser Micro Part 2 Dave Touretzky and Susan Finger 1. Symmetry and Reference Geometry Today, you ll make this part bear-like face and then cut it on the laser cutter:
Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly
Rotational Patterns of Sketched Features Using Datum Planes On-The-Fly Patterning a sketched feature (such as a slot, rib, square, etc.,) requires a slightly different technique. Why can t we create a
Getting Started. Chapter. Objectives
Chapter 1 Getting Started Autodesk Inventor has a context-sensitive user interface that provides you with the tools relevant to the tasks being performed. A comprehensive online help and tutorial system
Introduction to Autodesk Inventor User Interface Student Manual MODEL WINDOW
Emmett Wemp EDTECH 503 Introduction to Autodesk Inventor User Interface Fill in the blanks of the different tools available in the user interface of Autodesk Inventor as your instructor discusses them.
Custom Pillow Block Design Protrusion, Cut, Round, Draft (Review) Drawing (Review) Inheritance Feature (New) Creo 2.0
Custom Pillow Block Design Protrusion, Cut, Round, Draft (Review) Drawing (Review) Inheritance Feature (New) Creo 2.0 Rotatable pdf files: Casting Machining Grease Fitting Boss The general design of the
Advanced Modeling Techniques Sweep and Helical Sweep
Advanced Modeling Techniques Sweep and Helical Sweep Sweep A sweep is a profile that follows a path placed on a datum. It is important when creating a sweep that the designer plans the size of the path
Introduction to Sheet Metal Features SolidWorks 2009
SolidWorks 2009 Table of Contents Introduction to Sheet Metal Features Base Flange Method Magazine File.. 3 Envelopment & Development of Surfaces.. 14 Development of Transition Pieces.. 23 Conversion to
J. La Favre Fusion 360 Lesson 4 April 21, 2017
In this lesson, you will create an I-beam like the one in the image to the left. As you become more experienced in using CAD software, you will learn that there is usually more than one way to make a 3-D
Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder
Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic
Modeling an Airframe Tutorial
EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If
SolidWorks 95 User s Guide
SolidWorks 95 User s Guide Disclaimer: The following User Guide was extracted from SolidWorks 95 Help files and was not originally distributed in this format. All content 1995, SolidWorks Corporation Contents
Beginner s Guide to SolidWorks Level I
Beginner s Guide to SolidWorks 2013 - Level I Parts, Assemblies, Drawings, Simulation Xpress Alejandro Reyes MSME, CSWP, CSWI SDC PUBLICATIONS Schroff Development Corporation Better Textbooks. Lower Prices.
Pro/DESKTOP Tutorial Drafting Bow Compass
Pro/DESKTOP Tutorial Drafting Bow Compass Michael Flowers 2005 1 Objectives: To develop confidence with the Pro/DESKTOP software. To learn to utilize extrude, project, revolve, round, and chamfer features.
Beginner s Guide to SolidWorks Level I
Beginner s Guide to SolidWorks 2014 - Level I Parts, Assemblies, Drawings, PhotoView 360 and Simulation Xpress Videos Now includes SolidWorks training videos Alejandro Reyes MSME, CSWP, CSWI Multimedia
Laboratory Demonstration Exercises
Laboratory Demonstration Exercises 3-1 Lab Demo 1 - Plus Block Open SolidWorks, click on new document part OK. Right Click on Front Plane, click on Sketch icon (pencil w/ axes). In the sketch toolbar on
Up to Cruising Speed with Autodesk Inventor (Part 1)
11/29/2005-8:00 am - 11:30 am Room:Swan 1 (Swan) Walt Disney World Swan and Dolphin Resort Orlando, Florida Up to Cruising Speed with Autodesk Inventor (Part 1) Neil Munro - C-Cubed Technologies Ltd. and
DUE DATE: Friday 4/6/2018 at 3:30 PM
MECH 130 SPRING 2018 CAD LAB 4 FINAL REVISION HARDCOPIES NEEDED DUE DATE: Friday 4/6/2018 at 3:30 PM After the revised hitch, the ball and the pin parts were created from the Handout call LAB4 PART Creation,
Activity 5.5a CAD Model Features Part 1
Activity 5.5a CAD Model Features Part 1 Introduction In order to use CAD effectively as a design tool, the designer must have the skills necessary to create, edit, and manipulate a 3D model of a part in
Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge
Inventor (10) Module 1G: 1G- 1 Module 1G: Creating a Circle-Based Cylindrical Sheet-metal Lateral Piece with an Overlaying Lateral Edge Seam And Dove-Tail Seams on the Top Edge In Module 1A, we have explored
Creo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
Van Assembly. Creating an Assembly. Original by Steven Jaffe Modified by E. Brunelle 2/07 1
Van Assembly Creating an Assembly 1 Part One the Axle 1. Set Units to Inches 2. Create a New Design. 3. Save the Design as axleinl_cad1_1 in your Van folder. 4. Create a New Sketch on the Lateral workplane.
Introduction to ANSYS DesignModeler
Lecture 4 Planes and Sketches 14. 5 Release Introduction to ANSYS DesignModeler 2012 ANSYS, Inc. November 20, 2012 1 Release 14.5 Preprocessing Workflow Geometry Creation OR Geometry Import Geometry Operations
and Engineering Graphics
SOLIDWORKS 2018 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
SOLIDWORKS 2015 and Engineering Graphics
SOLIDWORKS 2015 and Engineering Graphics An Integrated Approach Randy H. Shih SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following
Autodesk AutoCAD 2013 Fundamentals
Autodesk AutoCAD 2013 Fundamentals Elise Moss SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Visit the following websites to learn more
Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material
ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2005 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com
CATIA Instructor-led Live Online Training Program
Course Outline Introduction & Understanding to CATIA Environment Introduction & Understanding to CATIA interface Starting new file Understand the Sketcher workbench of CATIA V5 Start a new file in the
SolidWorks Tutorial 1. Axis
SolidWorks Tutorial 1 Axis Axis This first exercise provides an introduction to SolidWorks software. First, we will design and draw a simple part: an axis with different diameters. You will learn how to
Creo Parametric 4.0 Basic Design
Creo Parametric 4.0 Basic Design Contents Table of Contents Introduction...1 Objective of This Textbook...1 Textbook Outline...2 Textbook Conventions...3 Exercise Files...3 System Configuration...4 Notes
Copyrighted. Material. Copyrighted. Material. Copyrighted. Material. Copyrighted. Material
ENGINEERING & COMPUTER GRAPHICS WORKBOOK Using SolidWorks 2008 Ronald E. Barr Thomas J. Krueger Theodore A. Aanstoos Davor Juricic SDC PUBLICATIONS Schroff Development Corporation www.schroff.com Better
Digital Camera Exercise
Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document
Introduction to Revolve - A Glass
Introduction to Revolve - A Glass Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Prerequisite Knowledge Previous knowledge of the following commands are required
Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1
Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Part Tutorial Exercise 5: Loft-Tube-1 [Complete] In this Exercise, We will set System Parameters first, then part options. Then, in sketch
Sash Clamp. Sash Clamp SW 2015 Design & Communication Graphics Page 1.
Sash Clamp 1 Introduction: The Sash clamp consists of nine parts. In creating the clamp we will be looking at the improvements made by SolidWorks in linear patterns, adding threads and in assembling the
AutoCAD 2018 Fundamentals
Autodesk AutoCAD 2018 Fundamentals Elise Moss SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit the following websites to learn more about
Objectives. Inventor Part Modeling MA 23-1 Presented by Tom Short, P.E. Munro & Associates, Inc
Objectives Inventor Part Modeling MA 23-1 Presented by Tom Short, P.E. Munro & Associates, Inc To demonstrate most of the sketch tools and part features in : Inventor Release 6 And, to show logical techniques
LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets
LAB 1A: Intro to SolidWorks: 2D -> 3D Brackets Set units Create Sketch Add relations Linear patterns Mirror Fillet Extrude Extrude cut First, set units. click Option on top of main menu Open Document Properties
Creo Parametric 2.0: Introduction to Solid Modeling. Creo Parametric 2.0: Introduction to Solid Modeling
Creo Parametric 2.0: Introduction to Solid Modeling 1 2 Part 1 Class Files... xiii Chapter 1 Introduction to Creo Parametric... 1-1 1.1 Solid Modeling... 1-4 1.2 Creo Parametric Fundamentals... 1-6 Feature-Based...
TOY TRUCK. Figure 1. Orthographic projections of project.
TOY TRUCK Prepared by: Harry Hawkins The following project is of a small, wooden toy truck. This exercise will provide you with the procedure for constructing the various parts of the design then assembling
Quick Start for Autodesk Inventor
Quick Start for Autodesk Inventor Autodesk Inventor Professional is a 3D mechanical design tool with powerful solid modeling capabilities and an intuitive interface. In this lesson, you use a typical workflow
FUSION 360: SKETCHING FOR MAKERS
FUSION 360: SKETCHING FOR MAKERS LaDeana Dockery 2017 MAKEICT Wichita, KS 1 Table of Contents Interface... 1 File Operations... 1 Opening Existing Models... 1 Mouse Navigation... 1 Preferences... 2 Navigation
To start a new drawing Select File New then from the dialog box, which appears select Normal.dft followed by OK.
Draft Tutorial This tutorial provides step-by-step instructions for the detailing of a drawing of the anchor block shown opposite. As you create this drawing, you will use the following drafting techniques:
Part 2: Earpiece. Insert Protrusion (Internal Sketch) Hole Patterns Getting Started with Pro/ENGINEER Wildfire. Round extrusion.
Part 2: Earpiece 4 Round extrusion Radial pattern Chamfered edge To create this part, you'll use some of the same extrusion techniques you used in the lens part. The only difference in this part is that
SolidWorks 2005 Tutorial. and MultiMedia CD. A Step-by-step Project Based Approach Utilizing 3D Solid Modeling
INSIDE: MultiMedia CD An audio/visual presentation of the tutorial projects SolidWorks 2005 Tutorial and MultiMedia CD A Step-by-step Project Based Approach Utilizing 3D Solid Modeling David C. Planchard
Lesson 4 Extrusions OBJECTIVES. Extrusions
Lesson 4 Extrusions Figure 4.1 Clamp OBJECTIVES Create a feature using an Extruded protrusion Understand Setup and Environment settings Define and set a Material type Create and use Datum features Sketch
Introducing SolidWorks
Introducing SolidWorks SAAST Robotics 2008 SolidWorks Software Visually-based 3-D Mechanical design software Engineers and Designers use it to: Quickly sketch out ideas Experiment with features, dimensions
Student + Instructor:
DRAFT OF DEMO FOR The following set of instructions are an optional replacement for the Section Views in SolidWorks. This demo should help prepare the students for the Out of Class HW Student + Instructor:
How to Make Drawings. 4. Open the part in SolidWorks, click on File, and then click on Make Drawing From Part.
How to Make Drawings 1. SVN Update (go to the topmost 2011 folder, right click, and go down to SVN update). This will download all of the drawings done by other people to your computer, as well as update
Part Design Fundamentals
Part Design Fundamentals 1 Course Presentation Objectives of the course In this course you will learn basic methods to create and modify solids features and parts Targeted audience New CATIA V5 Users 1
1. Creating geometry based on sketches 2. Using sketch lines as reference 3. Using sketches to drive changes in geometry
4.1: Modeling 3D Modeling is a key process of getting your ideas from a concept to a read- for- manufacture state, making it core foundation of the product development process. In Fusion 360, there are