ABW-4-SSP ABW-5-SSP 5 ABW-6-SSP 6 ABW-7-SSP 7 ABW-4-ESP ABW-5-ESP 5 ABW-6-ESP 6 ABW-7-ESP 7 ABW(*)24HSP ABW(*)36HSP. Furnished in pairs with hardware.

Transcription

1 Snap-In Splice Plate Designed to lock into place for easy alignment and installation. Packaged in pairs with zinc plated hardware. Provided as standard with each straight and fitting. ABW--SSP ABW--SSP ABW-6-SSP 6 ABW-7-SSP 7 Snap-In Expansion Splice Plate Allows for a 1 in. expansion or contraction of tray system. Packaged in pairs with zinc plated hardware. ABW--ESP ABW--ESP ABW-6-ESP 6 ABW-7-ESP 7 Horizontal Adjustable Plate Adjustable hinge plates provide maximum horizontal installation flexibility. ABW(*)2HSP ABW(*)36HSP (*) Insert Height. 6 7 For Tray Width 6 in. to 2 in. inclusive 30 in. to 36 in. inclusive Furnished in pairs with hardware. Vertical Adjustable Plate Hinged vertical plates provide maximum flexibility for changes in elevation. Furnished in pairs with hardware. ABW--VSP ABW--VSP ABW-6-VSP 6 ABW-7-VSP 7 T&B aluminum cable tray is composed of two distinct systems H-Style and U-Style. These systems are interchangeable. w w w. t n b. c a A99

2 Box to Tray Plates Designed to secure tray to electrical panels or boxes, walls or end supports. Furnished in pairs with hardware. ABW--BSP ABW--BSP ABW-6-BSP 6 ABW-7-BSP 7 Closure End Plate Reducing Splice Plate Provides closure for any tray end. Packaged with hardware. Offset Straight Used in pairs to provide a straight reduction or used with a standard splice plate for an offset reduction. Packaged with hardware. NOTE: (*) For offset reduction: insert width to be reduced. For straight reduction: insert 1/2 width to be reduced (2 required). Example: ABW-03-RSP = 3 in. offset reducer. Widths of Tray (in.) ABW-(*)-CEP 06 ABW-(*)-CEP 09 ABW-6(*)-CEP 6 12 ABW-7(*)-CEP (*) Insert width of Tray. ABW-(*)-RSP ABW-(*)-RSP ABW-6(*)-RSP 6 ABW-7(*)-RSP 7 Step Down Splice Plate Connects siderails of different heights. Hardware included. ABW(*)(**)SDS (*) Height 1. (**) Height 2. NOTE: Height 1 is greater then Height T&B aluminum cable tray is composed of two distinct systems H-Style and U-Style. These systems are interchangeable. A100

3 Mid-Span Splice Plate Mid-Span Splice Plate Features: Factory pre-drilled side rails for above series easy installation. Allows random connexion location. Tested loading 160 lb./ft., based on a 20 ft. simple beam test with 1. safety factor (tested with AH66 series). Supplied with stainless steel type 316 hardware. Available on ladder, vented or solid tray style. Only available in the following series of aluminum tray: AH6, AH6, AH66 and AH76*. *(20 ft. Support Span only). The Splice Plate 3/8 in.-16 x 3/ in. SS316 carriage bolt and serrated flanged nuts Cable Tray Mid-Span Slice Plate Reinforcing plate Part #: ABW6SSPMS 3/8 in.-16 x 1 in. SS316 carriage blot and serrated flanged nuts A101

4 Mid-Span Splice Plate Typical Installation of Mid-Span Splice Plate These heavy-duty splice plates are designed to allow random splice location, including the midspan for 20 ft. support spans. These splices are available for all long-span, ladder, vented or solid tray style. Ordering Information Straight Section Number Selection (AMS-6)-2-L09-6 Style Series Depth Width Bottom Type Length AMS Mid-Span Splice Prefix Series Series 6 Series 6 7 Series 7 6 (6 in.) 06 (6 in.) 09 (9 in.) 12 (12 in.) 18 (18 in.) 2 (2 in.) 30 (30 in.) 36 (36 in.) L06 6 in. rung spacing L09 9 in. rung spacing L12 12 in. rung spacing V Ventilated S Solid Trough 6 (6 meters) 288 (2 ft.) To order straight sections with Mid-Span Splice Plate, replace AH in the standard part number with AMS. Example: AH662L12-6 AMS662L12-6 A102

5 Place splices directly over supports No additional support required Over Support Splice Adaptor (Beam Installation) A103

6 Standard 1/ Span Typical Installation Supports are placed at 1/ span (2%). Expansion joints need extra support at 1/2 span to prevent excessive deformation of the tray under heavy loads. New Over Support Typical Installation Supports are placed right under the joints of the installation. The splice adaptor allows a wider distribution of the support, therefore minimizing the stress and deflection of the assembly. Standard Splice Plate 2% Span Standard Splice Plate 2 Over Support Splice Adaptor Span Span Expansion Splice Plate NOTE: Independent of the installation method chosen, AU/AH6 straight sections are CSA approved for Class E loading. (100%) Beam Installation ABW6-OSS-B BOTTOM VIEW Required on expansion joint only Required on anchored joint only Installation Components 1. Bonding jumper 2. Splice plate 3. Over support splice adaptor. Beam clamp. Hold down clamp 6. Structural beam 7. Strut (see right page) A10

7 Expansion % Span Splice Plate 2% Span Standard Splice Plate Extra Support Required Over Support Splice Adaptor Standard Splice Plate Over Support Splice Adaptor NEMA VE2: Splice joints should be designed and placed so as to maximize the rigidity of the cable tray over support. Splice plates and adaptors are part of a system specifically designed for placement directly over supports. Strut Installation ABW6-OSS-S INSIDE VIEW Required on expansion joint only Required on anchored joint only 7 Cable Tray Installation Every second splice must be an expansion joint. For gap setting at expansion joint, refer to NEMA chart on next page. For use with T&B Cable Tray series AH6. Max. load of 80 lb/ft, 20 ft span. Every joint must have a pair of over support splice adaptors (both standard splices and expansion splices) A10

8 ABW6-OSS-B Beam Installation Expansion over support beam 29 in. SHWCTC, Heavy-Duty hold down clamp (complete with mounting hardware) HGW-SHC, Standard hold down clamp E12-3/8x100EG, 3/8 in x 1 in. hex cap screws AC100-3/8EGC, 3/8 in. strut nut NOTE: Every expansion joint requires the use of a bonding jumper such as FBD16-1 (16 in., 600 amps) ABW6-OSS-S Strut Installation Expansion Plate Gap Chart Expansion over support beam 29 in. HGW-SHC, Standard hold down clamp E12-3/8x100EG, 3/8 in x 1 in. hex cap screws AC100-3/8EGC, 3/8 in. strut nut NOTE: Every expansion joint requires the use of a bonding jumper such as FBD16-1 (16 in., 600 amps) Metal Temperature at Time for Installation Gap Settings in. (mm) A106