Cable Tray. SF/273, 16th mile stone, Kavaraipettai-Satyavedu road, Thiruvallur T /52/53/54 F

Transcription

1 Cable Tray

2 Cable Tray Balsara is pioneer in manufacturing perforated and ladder - type Cable Trays along with accessories. Cable Trays are available in different sizes as per standard requirement of customer Cable Trays are available in different finishes like MS, pre - galvanized, Hot dip galvanized, powder coated and other. The accessories are available for perforated as well as ladder type are horizontal bends, vertical bend, inside bends, outside bends, reducers and tees. Cable Tray- Perforated Type Cable Tray - Perforated Type are ideal to install large volume of Heavy duty power cables. Perforation make full free air rating of cable,higher current flow can be achieved at the same cross section, Over heating and consecutive damaging of cable is avoided,coupler holes in side guarantees easy connecting of cable trays to each other,cable trays can be manufactured in Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminum-Commercial Grade Finish. Height of cable trays is varies from 25,35,50,70,75,100 & 125 mm, Width of cable trays is varies from 100 to 1000 mm,thickness of cable trays ranging from 10,12,14,16,18 SWG, i.e 3,2.5,2,1.6,1.2 mm

3 Horizontal Bend - Perforated Type Horizontal Bend - Perforated Type, are mainly use in combination with perforated type of cable trays to route the cables in 90 degree where two wall are conjoining,our product design allows the cable to route properly and chamfer of bend take care of cable not to Worn out, Peel off or Get damage while laying of cables. Horizontal Bend - Perforated Type, Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium-Commercial Grade Finish. Height Of Horizontal Bend - Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm, Width Of Horizontal Bend - Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of Horizontal Bend - Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm Cross Bend - Perforated Type Cross Bend-Perforated Type Are Mainly Use For Laying The Cable Horizontally Which Allows The Cable To Route From Four End, Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out, Peel Off Or Get Damage While Laying Of Cables.

4 Cross Bend-Perforated Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium-Commercial Grade Finish. Height Of Cross Bend-Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm, Width Of Cross Bend-Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of Cross Bend-Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm T Bend Perforated Type T Bend Perforated Type Is Suitable For Joining Cable Trays In Three Directions At 90 Degree Intervals In The Same Plane. Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out, Peel Off Or Get Damage While Laying Of Cables. T Bend Perforated Type, Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre- Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium-Commercial Grade Finish. Height Of T Bend Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm, Width Of T Bend Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of T Bend Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm

5 Horizontal Bend (Elbow) - Perforated Type Horizontal Bend (Elbow) - Perforated Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable In 90 Degree Where Two Wall Are Conjoining With Constrain Of Vertical Pillar Or Obstacle To It,, Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out, Peel Off Or Get Damage While Laying Of Cables. Horizontal Bend (Elbow) - Perforated Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium-Commercial Grade Finish. Height Of Horizontal Bend (Elbow) - Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm, Width Of Horizontal Bend (Elbow) - Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of Horizontal Bend (Elbow) - Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm Vertical Bend Outside - Perforated Type Vertical Bend Outside - Perforated Type Are Mainly Use In Combination With Perforated Type Of Cable Trays To Route The Cable Where The The Direction Changes To A Different Plane. Vertical Bend Outside - Perforated Type Changes Direction Downward From The Horizontal Plane. Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out, Peel Off Or Get Damage While Laying Of Cable.

6 Vertical Bend Outside-Perforated Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium-Commercial Grade Finish. Height Of Vertical Bend Outside - Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm, Width Of Vertical Bend Outside-Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of Vertical Bend Outside - Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm Ladder Type Ladder type cable trays - both welded and bolt & nut forms. We use corrosion resistant pregalvanized sheets (GI Sheets) or mild steel sheets for hot dip galvanized or powder coated for manufacture these ladder cable trays with corrosion resistant finish. Industrial cable trays consist of two longitudinal members (called side rails) w h i c h a re c o n n e c t e d b y individual transverse members called rungs. Side members are designed with top and bottom flanges turned to inside to give more space and access for loading and to avoid any damage for the cables. Our welded type ladder cable trays are in high demand among the customers. We use modern technology for engineering immaculate range of horizontal ladder cable trays as per customers needs.

7 Reducer Right Hand - Perforated Type Reducer Right Hand - Perforated Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable Which Is Suitable For Joining Cable Trays Of Different Widths In The Same Plane. A Reducer Right Hand - Perforated Type, When Viewed From The Large End, Has A Straight Side On The Left. Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out,Peel Off Or Get Damage While Laying Of Cable. Reducer Right Hand - Perforated Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium- Commercial Grade Finish. Height Of Reducer Right Hand - Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm,Width Of Reducer Right Hand - Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of Reducer Right Hand - Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm. Reducer Central - Perforated Type Reducer Central - Perforated Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable Where Cable Tray Is Suitable For Joining Cable Trays Of Different Widths In The Same Plane. Reducer Central - Perforated Type Has Two Symmetrical Offset Sides. Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out,Peel Off Or Get Damage While Laying Of Cable. Reducer Central-Perforated Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium-Commercial Grade Finish.

8 Height Of Reducer Central - Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm, Width Of Reducer Central - Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of Reducer Central - Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm Reducer Left Hand - Perforated Type Reducer Left Hand-Perforated Type Are Mainly Used In Combination With Perforated Type Of Cable Trays To Route The Cable Which Is Suitable For Joining Cable Trays Of Different Widths In The Same Plane.. A Reducer Left Hand-Perforated Type, When Viewed From The Large End, Has A Straight Side On The Left. Our Product Design Allows The Cable To Route Properly And Chamfer Of Bend Take Care Of Cable Not To Worn Out,Peel Off Or Get Damage While Laying Of Cable. Reducer Left Hand - Perforated Type Can Be Manufactured In Hot Dip Galvanized Finish(Galvanizing As Per Is-2626),Pre-Galvanized Finish(Material As Per Is-277),Powder Coating Finish(Powder Coating As Per Is-101),Stainless Steel Grade-As Per 316, 304 & In Aluminium-Commercial Grade Finish. Height Of Reducer Left Hand - Perforated Type Is Varies From 25,35,50,70,75,100 & 125 Mm,Width Of Reducer Left Hand - Perforated Type Is Varies From 100 To 1000 Mm,Thickness Of Reducer Left Hand-Perforated Type Ranging From 10,12,14,16,18 Swg, I.E 3,2.5,2,1.6,1.2 Mm

9 Cross Horizontal Bend 45 Degree Horizontal Bend 90 Degree Left Hand Reducer Centre Reducer Tee Vertical Bend Internal Left Side Reducer Vertical Bend