LT 800 WP. The economical insert drilling system. - for deep and large holes - from 40 to 100 mm diameter - for drilling depths up to 12 x D
|
|
- Antony Horton
- 5 years ago
- Views:
Transcription
1 LT 800 WP The economical insert drilling system - deep and large holes - from 40 to diameter - drilling depths up to 12 x D
2 The front cover shows a 50 LT 800 tool drilling a blind hole in a gas compressor shaft of 900 diameter (drilling depth 270, 6 x D). Contents Page System suary Ø 40 < System suary Ø Overview of inserts and drill head arrangements... 6 Program selection with drilling depth spectrum... 8 Program Basic adaptors, HSK reductions, HSK extensions...10 HSK holders and extensions...12 Drill heads and accessories...14 Cartridges and accessories...16 Interchangeable inserts and accessories...18 General technical parameters Assembly instructions ( ) Assembly instructions ( ) Coolant pressure and volume Recoended values the machining of steel Permance comparison Guhring guide/application recoendations... 24
3 LT 800 WP drilling system (Ø 40 ) Until recently, the economical production of deep and especially large holes above 40 diameter with carbide tools was only achievable with the assistance of costly special solutions. The successful development LT 800 WP now provides a modular and theree costeffective solution this difficult area of machining. This amazingly up to diameter and a drilling depth up to 12 x D! The holder is equipped with coolant ducts, the interchangeable inserts are produced in ultra fine grade carbide. Further, important advantages: Optimal adaptability to every machining task due to the combination possibilities of different tool holders (i.e. HSK, ISO taper, VDI) with extensions, reductions and drill heads with interchangeable inserts. Powerful double cutting edge thanks to lightly modified LTT ISO indexable inserts with circular lands positioned in pairs. Simple replacement of the drill head and the interchangeable insert. Accurate spotting provided by interchangeable insert with special Ratio point geometry. Good support through the complete drilling depth thanks to double-sided lands. Last but not least: LT 800 WP is ideally suited as a core drill the enlarging of drilled holes. Also remarkable is the fact that, depending on diameter and material, holes up to 12 x D can be produced, i.e. gun drilling. LT 800 WP 1
4 LT 800 System Suary 40 < 60 Holder (Ø-range) 400 ( ) 430 ( ) 460 ( ) 490 ( ) 520 ( ) 560 ( ) Basic adaptors HSK tool holder modules ISO taper basic adaptors Reductions Extensions 4512 page page page 11 Basic adaptors (VDI) 4510 page 10 Nom.-* Ø ,063 50,063 50,063 40,063 50,063 40,063 50,063 63,080 63, 63,080 63,, ,063, , always together with! * intermediate-ø please consult Guhring application technician. Direct installation in the spindle HSK 2 LT 800 WP
5 HSK holders 15 spiral 4142 page page page For intermediate s please pay attention on our recoendations on page 24! 63,105 63,180 63,120 63, x D 180 0,5 x D x D 2 x D Extensions 3 x D 15 spiral 10,150 12, Drill heads 1 x D 40,043 43,046 46,049 49,052 52,056 56,060 Cartridges mounting external indexable inserts (x 2 per drill head)* page 16 40,046 40,046 46,056 46,056 46,056 56,065 * cartridge arrangement see page 19 Nom.- Ø Holder (Ø-range) LT 800 WP 3
6 LT 800 System Suary 60 Holder (Ø-range) 600 ( ) 650 ( ) 700 ( ) 750 ( ) 800 ( ) 850 ( ) 900 ( ) 950 (95 ) Basic adaptors HSK tool holder modules ISO taper basic adaptors Reductions Extensions 4512 page page page 11 Basic adaptors (VDI) 4510 page 10 Nom.-* Ø always together with! * intermediate-ø please consult Guhring application technician. 50,063 50,080 60, 40,063 50,063 50,080 60,080 60, 63,080 63, 80, 120 Direct installation in the spindle, , , , , 200, HSK 4 LT 800 WP
7 HSK holders straight, stepped design, w/o chip chamber 4144 page page page ,135 63,240 80,160 80,290,180, ,5 x D ,5 x D x D 0,5 x D 330 Extensions 3 x D straight, stepped design, w/o chip chamber 40,210 48,255 2 x D 58,300 2 x D Drill heads 1 x D For intermediate s please pay attention on our recoendations on page 24! 060, , , , , , , , Cartridges mounting external indexable inserts (x 2 per drill head)* page 16 56,065 65,070 70,075 75,080 80,090 80,090 90, 90, * cartridge arrangement see page 19 Nom.- Ø Holder (Ø-range) LT 800 WP 5
8 LT 800 Overview of inserts and drill head arrangements Central interchangeable inserts Tool material Solid carbide Solid carbide Solid carbide Carbide grade K K/P K/P Surface finish predominantly suitable cast materials aluminium/al-alloys plastics universal machining of steel and cast materials universal machining of steel and cast materials External indexable inserts Type CCHX (outer) Design with circular land with circular land with circular land with circular land Tool material Solid carbide Solid carbide Solid carbide Solid carbide Carbide grade N15 K10 P25 M35 Surface finish predominantly suitable aluminium/al-alloys plastics cast materials universal machining of steel and cast materials C-steels, stainless and acid resistant steels Size 09 Size 12 Type LTT (inner) Design with circular land with circular land with circular land with circular land Tool material Solid carbide Solid carbide Solid carbide Solid carbide Carbide grade N10 K10 P25 P40 Surface finish predominantly suitable nonferrous metals, Al/Al-alloys, plastics cast materials universal machining of steel and cast materials C-steels, stainless and acid resistant steels Size 05 bright TiN-coated FIRE-coated TiAlN-coated Size 06 6 LT 800 WP
9 Cartridges mounting external indexable inserts (2 cartridges per drill head) 1 WSP CCHX 2 WSP LTT 1 WSP CCHX 1 WSP CCHX 1 WSP LTT Drill heads (arrangement examples) (arrangement overview of all s on page 19) Diameter adjustment with distance piece on both sides (using holder 950 as an example) thickness t in 95,0 96,0 97,0 98,0 99,0, without distance piece LT 800 WP 7
10 Drilling de LT 800 Representative program selection with drilling depth s Ø-range 40 < 60 HSK holder Drill head ~ 1.5 x D Drilling depth HSK ISO taper basic adaptor HSK holder Drill head ~ 3 x D Drilling depth HSK VDI basic adaptor HSK holder 1. extension 2. e ~ 12 x D Ø-range 60 HSK basic adaptor Drill head ~ 2 x D Drilling depth HSK ISO taper basic adaptor Reduction HSK holder ~ 3 x D Drilling depth 8 LT 800 WP
11 pectrum Size Size 490 xtension 3. extension Drill head Size 560 pth Size 600 Drill head Size 800 LT 800 WP 9
12 LT 800 Program ( further basic adaptors, reductions and extensions see Guhring catalogue GM 300 ) ISO-taper basic adaptors (DIN 69871, m AD) 4512 SK d2 d1 SW l 3 HSK-C d 2 kg , , , , , Note: Please order retention bolt separately l 3 SW Weight Basic adaptors (VDI) (DIN ) 4510 d 2 VDI SW l 2 ISOtaper VDI HSK-C d 2 kg , , , , , l 2 SW Weight 10 LT 800 WP
13 HSK reductions 4355 d 2 SW HSK-C HSK-A d 2 kg , , , SW Weight HSK extensions 4549 d1 d2 SW HSK-A /d 2 SW Weight kg 4549, , , , , , LT 800 WP 11
14 LT 800 Program HSK holders, with 15 spiral flutes 4142 d2 d4 d3 G1 l 2 holder d 2 HSK-A d 3 kg , M , M , / M , / M d 4 l 2 Thread G 1 Weight HSK holders, without flutes 4144 d2 d3 d4 G1 holder d 2 HSK-A d 3 kg , / M , / M , M , M , M , M d 4 Thread G 1 Weight 12 LT 800 WP
15 incl. retention spindle and Extensions, with 15 spiral flutes insert Torx screws 4148 d2 d4 G1 G1 d4 holder d 2 kg , M , / M d 4 Thread G 1 Weight incl. retention spindle and Extensions, without flutes 4149 insert Torx screws G1 d4 G1 d2 holder d 2 kg , / M , M , M d 4 Thread G 1 Weight LT 800 WP 13
16 LT 800 Program Drill heads (incl. retention spindle) 4150 d1 d2 d3 G1 d4 d2 d1 d2 G1 d3 l 3 d4 d3 retention Befestigungsspindel spindle d1 G1 l 3 d4 l 3 l 2 holder interch. insert cartidge arrangement with kg , ind. insert M , ind. insert M , ind. insert M , ind. insert M , ind. insert M , ind. inserts M , ind. inserts M , ind. inserts M , ind. inserts M , ind. inserts M , ind. inserts M , ind. inserts M , ind. inserts M , ind. inserts M Examples drill head arrangement see page 7 d 2 d 3 d 4 l 2 l 3 Thread G 1 Weight 14 LT 800 WP
17 Retention spindles extensions and drill heads 4164 G 2 d 4 Torx 2 Torx 1 G 1 G 2 Torx 2 Torx 1 G 1 holder d 4 Torx Thread TX1 TX2 G 1 G , ,5 38 T40 T30 M10 M10x , /560 12,5 45 T45 T30 M12 M12x , / T45 T45 M14 M14x , T45 T45 M16 M14x , T45 T45 M16 M14x1 Torx driver sockets retention spindle 4188 drillheads holders/extensions Driver sockets suitable Torx ,060 Drill heads T ,210 Holders and T ,180 extensions T Driver sockets suitable Torx ,105 Drill heads T ,300 Holders and extensions T Torque wrench Torx driver sockets ,000 Application Type Drive Drill heads, holders and extension Torque C 1/ Nm LT 800 WP 15
18 LT 800 Program Cartridges external indexable inserts 4160 Torx G SW d 2 b b b b holder no. of indexable inserts b , / , , , , holder no. of indexable inserts b , , / , 900/ * Cartridges incl. fastening screws, serrated lock washers and clamping screws indexable inserts (cartridge arrangements see page 7) Clamping screws Guhring std. No Fastening screws DIN EN ISO 4762 No G holder thread G Torx , / M3.5 T , M4 T , / M4.5 T15 holder thread G SW , M5 SW , * M6 SW , / M6 SW , / M6 SW5 Serrated lock washers No (Nord-Lock ) Distance pieces (sets) No s=1,8 s holder d , /430 3,9 7, , ,4 7, , ,4 9, , ,4 9, , ,5 10,8 holder b No.(x2)/thickness s , / /1.0/ , /1.0/1.5/ , / /1.0/1.5/ , /1.0/1.5/ , /1.0/1.5/ , / /1.0/1.5/ , 900/ /1.0/1.5/ LT 800 WP
19 LT 800 tools special applications 1. Cartridges drilling stacked sheets Drilling stacked sheets (e.g. heat exchanger) with the standard range is only possible from Ø due to the positioning of the indexable inserts in the cartridge. Illustrated below are cartridges required Ø 56, available on request x ind. inserts CCHX (per cartridge) b 3 x ind. inserts CCHX (per cartridge) b holder b 560/ holder b / / Special tools (example selection) Tool the machining of a welded workpiece fitted with solid carbide, FIRE-coated inserts Material: St52 Diameter: 49 followed by fineboring Diameter: 50 H7 Tool the machining (solid drilling) of a cylinder crankcase fitted with solid carbide, FIRE-coated inserts Material: CGI Diameter: 76 followed by reverse circular milling Chamfer 1.5 x 45 at Ø 76 Expansion joint adjustment fineboring with interchangeable inserts hole Ø 50 H7 chamfer 1.5 x 45 hole Ø 49 hole Ø 76 previously finebored area Ø 50 H7 pre-drilled area Ø 49 Travel Chamfer via reverse circular milling with 1 indexable insert LT 800 WP 17
20 LT 800 Program Central interchangeable inserts and accessories l 5 Form accurate fit of the interchangeable insert ensures safe clamping in holder. A Tool Werkzeugträger holder Anschlagschraube Stop screw (gesichert) (locked) Clamping Spannschraube screw (mit Sicherung) (with lock) d1 Torx h b Torx Ø-range Torque M d (N cm) T8 > A Insert Wechselplatte M d Section A A Interchangeable inserts incl. clamping screw Tool material Solid carbide Solid carbide Solid carbide Carbide grade K K/P K/P Surface finish Clamping screws Screwdriver G holder Nom.- h7 Cutting point l 5 Width b Height h ,00 6,2 8,5 13,6 Thread G Code no. Length with Torx M4x0.5 4, T8 M4.5x0.5 4, T8 Code no. Torx 8,001 T8 Torx bits 4917 Torque wrench 4915 Torx Drive Type Drive Torque Nm ,000 T8 1/ ,001 A 1/ bright TiN-coated FIRE-coated TiAlN-coated 18 LT 800 WP
21 External indexable inserts Type CCHX (outer) Insert arrangement overview Size , , , ,080 Size , , , ,080 Tool material Solid carbide Solid carbide Solid carbide Solid carbide Carbide grade K10 K15 P25 M35 Code no. Surface finish r Holder Central insert Indexable insert arrangement Indexable insert Indexable insert description Incircle Corner radius r Thickness s Length 09 CCHX09T o s Clamping screws 12 CCHX o Torx G 60 o Torx G l1 indexable insert No. of indexable inserts , ,501 2 Type LTT (inner) Code no. holder 400/ , , Length Thread G Torx 7.3 M3.5 T M4.5 T Size , , , ,040 Size , , , ,040 Tool material Solid carbide Solid carbide Solid carbide Solid carbide Carbide grade K10 K10 P25 M35 Surface finish Indexable insert indexable insert of Guhring no Clamping screws , ,500 Indexable insert description Incircle Corner radius r LTT05T LTT05T LTT06T LTT06T No. of indexable inserts holder 2 560/ / / o Torx l1 Thickness s G Thread G Torx 7,4 M2,5 T8 7,3 M3,5 T10 r s LT 800 WP 19
22 LT 800 Assembly Instructions Ø 40 < 60 ( ) 1. Assembly of the tool body 1.1. Assembly without extension Connect the drill head to the holder via the retention spindle (double-ended Torx fitting). The correct extension the Torx screw is required (see page 15)! Via the holder the retention spindle is then locked in anticlockwise direction and tightened to a recoended torque of M A = 25 Nm. Check dimension x. Driver 1 / 2 Retention spindle Optional is the locking of the assembly via the drill head in clockwise direction x Drill head HSK holder Extension Torx screw Torque wrench 1.2. Assembly with extension First, fit the extension to the holder in clockwise direction. Optional, see 1.1., is the locking via the holder in anticlockwise direction. Extension Retention spindle x Retention spindle Then, to complete the assembly, fit the drill head to the extension in clockwise direction. x Pre-assembled tool body 1.3. Important notes To fit retention spindle: Torque wrench ,000 (Driver 1 / 2 ) Torque M A = 25 Nm Retention spindle assembly length Dimension x in x Ø = /560 Ø-range dim.x Ø = 17.0 If new assembly, grease retention spindle (double-ended Torx fitting) with MOS 2 paste (prod. no ) at both ends (tool is supplied pre-greased!) Check dimension x and correct if necessary! Pay attention to position of driver to flute! 2. Assembly of cartridges and indexable inserts 2.1. Insert distance piece If increase in Ø is required, insert identical distance pieces (left and right). If basic Ø modification is not required, continue and go to point 2.2. (see also page 7). Distance piece seat Cartridge seat 1. Distance piece 2.2. Cartridge assembly Fit cartridge to the drill head using the fastening screws and the serrated lock washers. Ensure a seamless fitment to the drill head! 1. Serrated lock washer 1. Fastening screw 1. Cartridge 2.3. Fitting the indexable inserts Fit the indexable inserts to the cartridges using the supplied clamping screws. Indexable insert seat Indexable insert 1 Indexable insert clamping screw 3. Central insert installation 3.1. Position central insert in insert seat Insert seat Central insert 3.2. Fasten insert with supplied clamping screw (Torque 180 Ncm). Replace clamping screw after every insert change. Clamping screw Accessories the central insert installation Clamping screw, Torx 8, 1071 Torx- Torque / Ncm Code no. T ,000 T ,500 Torque wrench, ,001 Torx-Bits T8 Art.-Nr ,000 Please follow safety recoendations on page LT 800 WP
23 Ø 60 ( ) 1. Assembly of the tool body 1.1. Assembly without extension Connect the drill head to the holder via the retention spindle (double-ended Torx fitting). The correct extension the Torx screw is required (see page 15)! Via the holder the retention spindle is then locked in anticlockwise direction and tightened to a recoended torque of M A = 50 Nm. Check dimension x. Driver 1 / 2 Retention spindle Optional is the locking of the assembly via the drill head in clockwise direction x Drill head HSK holder Extension Torx screw Torque wrench 1.2. Assembly with extension First, fit the extension to the holder in clockwise direction Retention spindle Optional, see 1.1., is the locking via the holder in anticlockwise direction. Extension x Then, to complete the assembly, fit the drill head to the extension in clockwise direction. Retention spindle x Pre-assembled tool body 1.3. Important notes To fit retention spindle: Torque wrench ,000 (Driver 1 / 2 ) Torque M A = 50 Nm Retention spindle assembly length Dimension x in Ø-range dim.x 600/650 Ø = Ø = 13.0 x Ø = 14.0 If new assembly, grease retention spindle (double-ended Torx fitting) with MOS 2 paste (prod. no ) at both ends (tool is supplied pre-greased!) Check dimension x and correct if necessary! Pay attention to position of driver to flute! 2. Assembly of cartridges and indexable inserts 2.1. Insert distance piece If increase in Ø is required, insert identical distance pieces (left and right). If basic Ø modification is not required, continue and go to point 2.2. (see also page 7). Distance piece seat Cartridge seat 2.2. Cartridge assembly Fit cartridge to the drill head using the fastening screws and the serrated lock washers. Ensure a seamless fitment to the drill head! 1. Cartridge 2.3. Fitting the indexable inserts Fit the indexable inserts to the cartridges using the supplied clamping screws. 2x3 clamping screws LTT-inserts 1 and 2 1. Distance piece 1. Fastening screw 1. Serrated lock washer Cartridge seat CCHX-insert 1 Insert seats 3. Central insert installation 3.1. Position central insert in insert seat 3.2.Fasten insert with supplied clamping screw (Torque 180 Ncm). Replace clamping screw after every insert change. Clamping screw Accessories the central insert installation Clamping screw, Torx 8, ,500 Torque 180 Ncm Torque wrench, ,001 Torx-bit, ,000 Please follow safety recoendations on page 24. Insert seat Central insert LT 800 WP 21
24 LT 800 Technical Inmation Required coolant pressure and volume The optimal, good and minimum required coolant volumes shown in the diagrams apply only to LT 800- tools and are not machine dependent. The pressure values in contrast are dependent on the machine, because machines are equipped with different cooling systems and subsequently have different leakage characteristics. Theree, the pressure values illustrated serve only inmation and assessing the of volume. Coolant pressure p [bar] maximum pressure minimum pressure maximum volume minimum volume Coolant volume V [l/min] Tool diameter Recoended values the machining of steel Workpiece material: unalloyed heat treatable steel Tensile strength: N/ 2 Cutting speed: m/min Feed ce loading f = 0.4 Feed ce Ff [kn] f = Tool diameter Power requirement f = 0.4 Power requirement Pc [kw] f = Tool diameter Torque requirement 2,2 f = 0.4 1,8 Torque Mc [knm] 1,4 1,0 0,6 f = 0.2 0, Tool diameter 22 LT 800 WP
25 Permance Comparison 1 Tools LT 800 Competitor ind. ins. drill 2 Tools LT 800 Competitor ind. ins. drill Ø58 Ø48 Central interchangeable insert (WP) 2485 F 4172 F 1. Indexable inserts (WSP), inner LTT 05T Indexable inserts (WSP), outer 4181 F CCHX09T308Rf Holder drilling depth 5 D Holder DIN 1835 Workpiece Main spindle Machine CNC-lathe GILDEMEISTER Workpiece material 31Cr MoV9 (1.8519) Hole-Ø 58 Drilling depth 300 Number of holes 1 (per spindle) Cutting parameters Cutting speed v c (m/min) Feed rate f (/rev.) Result: Central interchangeable insert (WP) 1047 S Indexable insert (WSP) 4181 S CCHX09T308Rf Holder drilling depth 8 D Holder ABS-80 Workpiece Motor housing Machine WALDRICH Workpiece material GGG 40 Hole-Ø 50 Drilling depth 400 Number of holes 72 (per housing) Cutting parameters Cutting speed v c (m/min) Feed rate f (/rev.) Result: Nominal value basis Nominal value basis 3 Tools Machining time reduction in % LT 800 Competitor ind. ins. drill 4 Tools Machining time reduction in % LT 800 Competitor ind. ins. drill Ø86 Ø96 Central interchangeable insert (WP) 2485 F 4172 S 1. Indexable inserts (WSP), inner DFT05T S 2. Indexable inserts (WSP), centre DFT05T S 3. Indexable inserts (WSP), outer CCMT09T304 Holder drilling depth 4 D Holder HSK-A Workpiece Turbine housing Machine WALDRICH Workpiece material GS17CrMo5-5 (1.7357) Hole-Ø 86 Drilling depth 320 Number of holes 12 (per housing) Cutting parameters Cutting speed v c (m/min) Feed rate f (/rev.) Result: Central interchangeable insert (WP) 2485 F 4172 S 1. Indexable inserts (WSP), inner LTT06T Indexable inserts (WSP), centre 4172 S LTT06T S 3. Indexable inserts (WSP), outer CCHX09T308 Holder drilling depth 4 D Holder HSK-C80 Workpiece Extrusion shaft Machine CNC-lathe VDF Workpiece materia4crmov6-9 (1.7735) Hole-Ø 96 Drilling depth 300 Number of holes 1 (per shaft) Cutting parameters Cutting speed v c (m/min) Feed rate f (/rev.) Result: Nominal value basis Nominal value basis Machining time reduction in % Machining time reduction in % S TiN-coated F FIRE-coated LT 800 WP 23
26 LT 800 General Technical Inmation GUHRINGGUIDE Application recoendations through holes supporting lands of the outer indexable inserts must remain in permanent contact drilling depths in excess of 7xD centering is recoended with equal point angle of 140, or larger, to approximately 2/3 cutting edge diameter of the central interchangeable insert (do not apply standard centre drill to DIN 332). If centering is impossible, spot-drill with reduced feed. interrupted cutting (cross holes, grooves, oblique entry/exit) is not recoended without prior tests. We recoend reducing the feed by approximately 50%. the standard LT 800 tool system is also suitable drilling up to diameter 55.9 in stacked metal sheets. For drilling of stacked metal sheets above diameter 56, the standard cartridge must be replaced with a cartridge with a suitable indexable insert arrangement (see page 17). when replacing the central interchangeable insert (RT 800), we recoend replacing the clamping screw with a new one (with clamping thread protection). with turning machines (vertical drilling tool) it must be ensured the tool operates precisely on centre. pre-requisite optimal machining results is a sufficient coolant supply (see diagrams page 22). The tool possesses only limited suitability dry machining or MQL. The cutting speed should be reduced by approxiamtely 30% whilst retaining the same feed rate. With intermedial s to the standar steps please prepare a fitting distance tape and place it between cartridge and drill head or distance piece (see assembly instructions page 20/21). Example: nom.-ø 41,5 adjusting Ø 40.0 drill head / two cartridges x 0.50 two 0.5 distance pieces from set x 0.25 two 0.25 precision distance tapes (or sim. distance sheets) Ø 41.5 Safety recoendations: with rotating workpieces, a disc is created on hole break through. Due to the centrifugal effect there is a possible risk of accident! Safety precautions must be followed. in order to prevent damage to machine and tool, we recoend the prior determination of the required power and torque (see diagrams on page 22). 3xD drill Drilling depth Material specific coolants: soluble oil neat oil air Material group Coon structural steels Free-cutting steels Unalloyed heat treatable steels Alloyed heat treatable steels Unalloyed case hardened steels Alloyed case hardened steels Nitriding steels Tool steels High speed steels Spring steels Stainless steel, sulphured austenitic martensitic Hardened steels Special alloys Cast iron Spheroidal graphite iron and malleable cast iron Chilled cast iron Titanium and Ti-alloys Aluminium and Al-alloys Al wrought alloys Al cast alloys 10 % Si > 10 % Si Magnesium-alloys Copper, low-alloyed Brass, short-chipping long-chipping Bronze, short-chipping Bronze, long-chipping Material examples, new description (old description in brackets) Figures in bold = material no. to DIN EN S185(St33), P275N(StE285), P235GH(H1), P265GH(H2) E295 (St50-2), E360 (St70-2), P500NH (WStE500) SMnPb30 (9SMnPb28), SMn37 (9SMn36) S20 (45S20), (60S20), SPb20 (45SPb20) C22, C30E (Ck30) C45, C45E (Ck45) C60, C60E (Ck60) MnSi4, Cr2, Cr NiCr6, Cr4, CrMo (C10), C10E (Ck10) Cr NiCr13 (15NiCr13), MnCr5, CrMo CrAl CrMoV9, CrAlNi C75W, Cr6, CrMoV X210Cr12, X42Cr13, WCr6, X45NiCrMo S , S 6-5-2, S Si7, Cr3, CrV4 (51CrV4) X12CrS13, X14CrMoS17, X6CrMoS17, X8CrNiS X5CrNi18-10, X6CrNiTi18-10, X6CrNiMoTi X20CrNi 17 2 (X17CrNi16-2), X39CrMo17-1, X2CrMoTi18-2 Nimonic, Inconel, Monel, Hastelloy EN-GJL-(GG10), EN-GJL-200(GG20) EN-GJL-250(GG25), EN-GJL-350(GG35) EN-GJS-500-7(GGG50), EN-GJMW-350-4(GTW35) EN-GJS-700-2(GGG70), EN-GJMB-700-2(GTS70) Ti99,5, TiAl5Sn2,5, TiCu TiAl6Zr5, TiAl6V4, TiAl4Mo4Sn2,5, - TiAl8Mo1V Al99,5, AlMgSi1, AlMg AlMgSiPb, AlCuMg1, AlMg3Si, AlZnMgCu1, G-AlSi5Cu1, G-AlSi7Cu3, G-AlSi G-AlSi12, G-AlSi12Cu, - G-AlSi12CuNiMg MgMn2, G-MgAl8Zn1, G-MgAl6Zn SE-Cu, CuSn6, G-CuSn5ZnPb CuZn39Pb2, CuZn39Pb3, CuZn43Pb CuZn20, CuZn33, CuZn37Pb0, CuSn7ZnPb, CuPb5Sn5, CuPb10Sn CuNi18Zn19Pb CuAl5, CuAl9Mn, CuSn CuAl11Ni, CuBe2 Tensile strength N/ > > Interchangeable insert material 330 HB HRC >48-60 HRC 240 HB <300 HB 240 HB <300 HB 350 HB Hardness Coolant Carbide grade Holder s Nom.-Ø range Feed rate f (/rev.) <60 v c m/min Solid dependent on int 24 LT 800 WP
27 ing depth 6xD drilling depth 9xD 12xD carbide erchangeable insert type Solid carbide dependent on interchangeable insert type Solid carbide dependent on interchangeable insert type Solid carbide dependent on interchangeable insert type < < <60 60 v c m/min v c m/min v c m/min v c m/min v c m/min v c m/min v c m/min LT 800 WP 25
28 Guhring ohg P.O. Box 247 D Albstadt Herderstr D Albstadt Telephone: Fax: Our product range: 1. Drilling Tools in High Speed Steel and Carbide Twist drills Ratio drills Micro-precision drills Oil feed drills Subland drills Centre drills Core drills Gun drills Drilling systems with interchangeable inserts 2. Thread Cutting Tools in High Speed Steel and Carbide Machine taps and fluteless taps Oil feed taps and oil feed fluteless taps Hand taps Thread milling cutters Dies 3. Milling Cutters in High Speed Steel and Carbide Ratio end mills Slot drills End mills Radius profile cutters Hard profile cutters Diesinking cutters 4. Reaming Tools in High Speed Steel and Carbide NC machine chucking reamers Machine and machine chucking reamers Taper pin reamers Hand reamers 5. Countersinking Tools in High Speed Steel and Carbide Countersinks, counterbores and spot facers Short counterbores, back spot facers De-burring tools No liability can be accepted printing errors or technical changes of any kind. Our Conditions of Sale and Terms of Payment apply. Available on request. 6. Cutting Tools in ultra-hard materials Face milling cutter PF 0 Cermet and ceramic tools PCD- and PCB-tipped tools 7. Coated Tools A-tools, TiAlN-coated SuperA-tools, AlTiN-coated C-tools, TiCN-coated F-tools, FIRE-coated (allround) P-tools, AlCrNN-coated S-tools, TiN-coated (allround) M-tools, MolyGlide-coated 8. Modular Tooling Systems Tooling system GM 300 Tool holders, clamping systems and accessories to ISO 12164, DIN and DIN transfer lines, machining and turning centres Flexible tooling system GE a tooling system the combined machining operations facing, chamfering, boring, centering etc. ISO indexable inserts, short clamping holders and KV 400 cartridges 9. Special Tools to sketch or drawing, the more complex, the better 10. Carbides precision cutting tools 11. Carbide Special Parts the ming, machining and wear protection industry Cold heading dies, ribbed rolls, dies, mandrels, drawing dies, gear cutters, etc. 12. Tool Restoration Service Re-grinding, re-coating, tool management /0783-XI-15 Printed in Germany
LT 800 WP. The economical insert drilling system. - for deep and large holes - from 40 to 100 mm diameter - for drilling depths up to 12 x D
LT 800 WP The economical insert drilling system - deep and large holes - from 40 to diameter - drilling depths up to 12 x D The front cover shows a 50 LT 800 tool drilling a blind hole in a gas compressor
More informationTool dispatch max. 3 weeks. Made by Guhring
HR 500 ActivE Special range of HR 500 solid carbide high performance reamers - cutting rates equal to cermet - broad range of application - numerous special geometries possible Tool dispatch max. 3 weeks
More informationRT 100 T NEW. Solid carbide spiral-flute deep hole drills. Now from 15 to 40 x D. Made by Guhring
Solid carbide spiral-flute deep hole drills NEW Now from 15 to 40 x D Made by Guhring ex-stock range Available ex-stock now: The spiralflute deep hole drill. The program includes standard drills for drilling
More informationHSS Specialists. Special design high speed steel drills for special machining tasks
HSS Specialists Special design high speed steel drills for special machining tasks Guhring s HSS Guhring has been a specialist in drilling tools for more than a century. This not only applies to the broad
More informationGM 300 CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING AND LUBRICATION
GM 300 CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING AND LUBRICATION CHECK- AND MEASURING INSTRUMENTS FOR OPTIMAL TOOL CLAMPING AND LUBRICATION Pre-requisite for perfect machining results
More informationPF 3000 Face Milling Cutter
Perfection in machining PF 3000 Face Milling Cutter UHRIN YOUR WORLD-WIDE PARTNER ADVANTAES axially adjustable inserts standard tool Ø 63 250 available ex-stock reduced spindle loading thanks to light
More informationRF 100 A. The specialist for aluminium and Al-wrought alloys
- excellent surface quality for finishing operations - up to 80 % higher feed rates thanks to - innovative cross cutting face geometry RF 100 A The specialist for aluminium and Al-wrought alloys Guhring
More informationTHE NEW GENERATION. Pionex the new generation FLUTELESS MACHINE TAPS
TE NEW GENERATION torque reduction up to 30 % reduced axial forces increased tool life improved surface finish quality ionex the new generation FLUTELESS MACINE TAS GURING YOUR WORLD-WIDE ARTNER ionex
More informationPowerful for the energy technology
Powerful for the energy technology GÜHRING - your world-wide partner powerful for the Energy technology Taps for ISO metric threads, M16 - M39 SW d2 l 1 l 2 d 1 d k Guhring no. 778 Standard DIN 2184-1
More informationPowerful for the energy technology
Powerful for the energy technology GÜHRING - your world-wide partner Industrial sectors such as transmission, turbine and energy plant manufacturers require exceptionally large threads. For exactly such
More information+1-508-653-8897 800-992-4766 www.toolmex.com Dear Valued Customers, The TMX Team have broadened our line of round cutting tools and holders to ensure that you have the productivity tools that you need
More informationThread Mills. Solid Carbide Thread Milling Cutters
Thread Mills Solid Carbide Thread Milling Cutters Thread milling cutters by Features and Benefits: Sub-micro grain carbide substrate Longer tool life with tighter tolerances More cost-effective than indexable
More informationSolid Carbide Thread Milling Cutters
Solid Carbide Thread Milling Cutters Second Edition Thread milling cutters by Features and Benefits: Sub-micro grain carbide substrate Longer tool life with tighter tolerances More cost-effective than
More informationCutting Tools. Round Tooling TMX-TOOL Fax
Round Tooling +1-508-653-8897 844-TMX-TOOL Fax +1-508-653-5110 www.tmxtools.com 245 Quick Lookup Round Tooling DRILLS...247 ANNULAR CUTTERS...295 REAMERS...299 COUNTERBORES AND COUNTERSINKS....321 CARBIDE
More informationHSS Specialists. Special design high speed steel drills for special machining tasks
HSS Specialists Special design high speed steel drills for special machining tasks Guhring s HSS Guhring has been a specialist in drilling tools for more than a century. This not only applies to the broad
More informationFeatuRes OF GeOMetRy. synchro tapping chuck (er type) advantages. GUIdE LINE TO ICONS
FeatuRes OF GeOMetRy synchro tapping chuck (er type) advantages GUIdE LINE TO ICONS Working Material GS s with good machinability Rm
More informationSolid carbide thread milling cutters
SECIAL OFFER NEW rogramming software for thread milling cutters and drill thread milling cutters CNC Gühro ThreadMill Thread milling cutters with and without chamfer Universal thread milling cutters Drill
More informationCompetence Gun Boring. KOYEMANN Floating Tools Power Reamer
Competence Gun Boring KOYEMANN Floating Tools Power Reamer R The KOYEMANN Floating Principle Reaming has been used for fine machining bores with excellent results from the very start of cutting technology.
More informationClamping devices 521
Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps
More informationPrecision Cutting Tools RE-GRINDING AND RE-COATING SERVICE
Precision Cutting Tools RE-GRINDING AND RE-COATING SERVICE Price List 2017 Maximum economic efficiency thanks to refurbishing to original quality Even the most resilient tool will wear at some time when
More informationIn hall 4, stand A42, you can experience Intelligence in Production. The following trade show highlights can be seen at EMO:
Guhring at EMO 2013 Intelligence in Production with precision tools from Guhring In the spirit of the motto of this year s EMO, from 16th to 21th September in Hanover, Guhring is introducing trendsetting
More informationDeburring tools GUHRING YOUR WORLD-WIDE PARTNER. EW 100 G Deburring fork EWR 500 Deburring reamer EW 100 S Deburring spiral. Chamfering milling cutter
EW 100 G Deburring fork EWR 500 Deburring reamer EW 100 S Deburring spiral Chamfering milling cutter Front/back deburrer Ball nose deburrer EW Deburring reamer EWR 500 Deburring tools GURIG YOUR WORLD-WIDE
More informationHOLLFELDER CUTTING TOOLS. Main Catalog H6
HOLLFELDER CUTTING TOOLS Main Catalog H6 HOLLFELDER-GÜHRING CUTTING TOOLS Your competent partner in the area of metal chip removal. At our two company locations in Nuremberg und Zorbau (Germany) we design
More informationWind power Tooling solutions for all components and all materials from one source
Wind power Tooling solutions for all components and all materials from one source application specific tool materials and coatings innovative geometries for highest accuracy and quality intelligent special
More informationQUALITy. Implant machining. Guhring Precision tools for the machining of stainless steel and titanium-alloy implants
QUALITy that goes under the skin Implant machining Precision tools for the machining of stainless steel and titanium-alloy implants 2012 2 Implant machining ingeniously close to ature Stainless steel and
More informationno mm no Dividers with scriber 150 mm NEW Square wedge-shaped knife edges on the length side
Summer Promotion valid until 30.06.2013 all quoted prices are incl. VAT for deliveries to EU countries to customers with valid VAT-no. and for deliveries in non EU member countries the VAT is not applicable
More informationTRAINING MANUAL. Part INTRODUCTION TO TWIST DRILLS
PRESTO INTERNATIONAL UK LTD TRAINING MANUAL Part 2 INTRODUCTION TO TWIST DRILLS - 1 - DEFINITION:- A rotary end cutting tool having two or more cutting lips, and having two or more spiral (helical) or
More informationFeatures. Special forms are possible
Center Drill >> The is a trademark of Nine9, the developer of the first indexable center drill in the world.(patented) Offering an indexable insert system for the 1st time, Nine9 s design improves your
More informationand AM-CAT-COREV(GB)-11/08 High Performance Indexable Insert Systems
and AM-CAT-COREV(GB)-11/08 High Performance Indexable Insert Systems Allied Maxcut Engineering Co. Limited AMEC Indexable Drill Range The AMEC range of adjustable indexable carbide drills provides the
More informationDeburring and chamfering
eburring and chamfering for smooth finishing operations 2 Chamfering in smallest dimensions CrazyMill Frontchamfer matches ideally the existing cutting tool program of Mikron Tool. Available from diameter
More informationPUNCHING DRILLING HEBEN LIFTING CUTTING DEBURRING
PUNCHING DRILLING LIFTING CUTTING DEBURRING www.alfra.de E-EN E ALFRA Edge-Milling and Deburring Devices Overview KFV KFH 150 Page 7 78 2520 25100 Prism mounting L = 150 / W = 20/40 End mill Ø 45 or straight
More informationRATIO. 60 % longer tool life. Ratio high-performance roughing cutter with flat knuckle-type teeth
INNOVATIONS 2017/2018 Ratio high-performance roughing cutter with flat knuckle-type teeth 60 % longer tool life The optimised roughing geometry with asymmetrical knuckles reduces the cutting pressure in
More informationTHREAD MILLING CUTTERS THE COMPLETE PROGRAMME
EN Precision Cutting Tools THREAD MILLING CUTTERS THE COMPLETE PROGRAMME + NEW: Micro thread milling cutters from M1.4 ISO code P M K N S H Steel, high-alloyed steel Stainless steel Grey cast iron, spher.
More informationPrecision made in Germany. As per DIN The heart of a system, versatile and expandable.
1 Precision made in Germany. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).
More informationThe new generation with system accessories. Made in Germany!
1 The new generation with system accessories. Made in Germany! For face, longitudinal and taper turning, thread-cutting. For machining steel, brass, aluminium and plastic. Mounting flange for fastening
More informationMarch weeks. surcharge for
March weeks valid until 31.03.2012 all quoted prices are incl. 19% VAT for deliveries in the EU countries to customers with a valid VAT-no. and for deliveries in not EU member countries the VAT is not
More informationHOLLFELDER CUTTING TOOLS
HOLLFELDER CUTTING TOOLS HOLLFELDER-GÜHRING CUTTING TOOLS Your competent partner in the area of metal chip removal. At our two company locations in Nuremberg und Zorbau (Germany) we design and manufacture
More informationUseful accessories for lathe and milling systems.
1 Useful accessories for lathe and milling systems. Nearly all accessories are supplied in wooden boxes. For proper and value preserving storage! Dividing attachment TA 250 For precision lathe PD 250/E,
More informationReaming. MAPAL MonoReam. Systematic versatility NEW
Reaming MAPAL MonoReam Systematic versatility NEW MAPAL MonoReam With the newly developed multi-bladed reamers in the 600, 700 and 800 series, MAPAL is offering a new, simple, highperformance, standardised
More informationLEADING SOLUTIONS IN THREAD MILLING TECHNOLOGY
LEADING SOLUTIONS IN THREAD MILLING TECHNOLOGY Thread with Maximum Confidence, Depth, Versatility and Economy. Emuge Shur-Thread TM, Threads-All TM, Vario-Z and NPT Solid Carbide Thread Mills; and Gigant-ic
More informationThe new generation with system accessories. Made in Europe!
1 The new generation with system accessories. Made in Europe! Of cast iron, wide-legged prismatic guide. For vibration-free work even at high loads. Rear flange for mounting the mill/drill head PF 230.
More informationCHAPTER C. Width of cut. Tool type. DOC t max. Page number
Step #1: Establish bore diamter Step #2: Find Depth of ut (DO) requirements Step #3: Follow column and row to find correct tool type Step #4: Look up tool type to find available widths HAPTER DO t max.063
More informationCompatibility overview of accessories for milling machines
Compatibility overview of accessories for milling machines Accessories Item No. BF16 BF20/L MB4 F40E BF30 MT3 Copy and planing cutter head MT 2 3350212 BF30 BF46 BF46 ISo30 ISO40 MT4 MF1 MT 50 MT2BV Mf2
More informationVarious other types of drilling machines are available for specialized jobs. These may be portable, bench type, multiple spindle, gang, multiple
Drilling The process of making holes is known as drilling and generally drilling machines are used to produce the holes. Drilling is an extensively used process by which blind or though holes are originated
More informationINSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS
INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. A1-Tools... 5 2.1 Technical Data... 5 2.2 Overview: Main Components...
More informationNew generation of the PCD face milling cutters. EcoMill-Blue and RapidMill-Blue
New generation of the PCD face milling cutters EcoMill-Blue and RapidMill-Blue 2 EcoMill-Blue and RapidMill-Blue New generation of the PCD face milling cutters EcoMill-Blue and RapidMill-Blue New generation
More informationProduct Overview. for perfect connections
Product Overview for perfect connections TOOL HOLDERS FOR DRILLING, TAPPING & REAMING Smart solutions for high quality clamping systems in tapping applications Tapping solution range from M1 M200 Quick
More informationMASONRY DRILL and CHISEL
MASONRY DRILL and CHISEL STRAIGHT SHANK MASONRY DRILL 8 Available in common size Made from carbide alloy Drill tip is welded with YG-carbide alloy steel Content of KW00537: Size: 4, 5, 6, 8, 0mm Content
More informationCompatibility overview of accessories for milling machines
Compatibility overview of accessories for milling machines Accessories Item No. BF16 BF20/L MB4 F40E BF30 MT3 BF30 ISo30 BF46 ISO40 BF46 MT4 MF1 MT 50 MT2BV MF2 MF4 MT100 MT 200 MT 8 MX 3 MX 4 MT8 Copy
More informationReaming. Tool Systems
Milling Thread Milling Trapezoid thread ACME thread Knuckle thread TC 50 / TC 80 18-79 1 Face Finish Milling 80-85 2 Notch Impact Test 86-91 3 Gear Milling 92-95 4 Slot Milling 96-123 5 Contour and Radius
More informationNO NEED TO CHOOSE NINE9 DOES IT ALL!
NO NEED TO CHOOSE NINE9 DOES IT ALL! Cat. No. 11.a NC Spot Drills Corner Rounding Cutters & Engraving Tools Various applications of NC Spot Drill We Focus: Higher efficiency Position accuracy Long tool
More informationINSTRUCTIONS FOR USE B2 FORM KNURLING TOOL
INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. B2 Tools... 6 2.1 Technical Data... 6 2.2 Overview: Main components... 7
More information-treme thread cutting. Tiny Tools. New Products. Metric
TM -treme thread cutting Tiny Tools New Products Metric 2014-2015 Tiny Tools Broaching Tools for Hexagon Keys - HK The HK broaching system have been developed to machine internal keyways inside blind or
More informationAPRIL 2009 / NEW-100 / PAGE 1 OF 13
APRIL 2009 / NEW-100 / PAGE 1 OF 13 The standard UNIDEX line covers reaming applications from 5/16 to 1 1/4 diameter. The single indexable blade and high wear resistant carbide or cermet pads provide a
More informationSYMBOL INDEX HSS V3. Special heat treatment. HSS-Co 8% CARBIDE. Powder Steel High performance ASP 23 BI/CV. GOLD Gold finish HARD LUBE
526 Technical Information GENERAL ICONS DIN DIN Norm TOL Tolerance Standard quality Professional quality Extra porfessional quality Supreme quality MATERIALS High speed steel M2 quality G High speed steel
More informationHPC FACE MILLS for rough and finish machining
HOLLFELDER CUTTING TOOLS THE ORIGINAL HPC FACE MILLS for rough and finish machining THE ULTIMATE EVOLUTION! AXIALLY CLOSED CHIP FLUTES EXTREMELY HIGH NUMBER OF CUTTING EDGE FOR FINISH MACHINING CUTTERS
More informationOptimized flute design Better chip evacuation. Carbide substrate Higher heat resistance, higher speed.
Thread Mills Available for the first time, our solid thread mills are designed to be the highest quality thread milling solution. WIDIA-GTD Cut up to 63 HRC. Improved overall thread quality. Optimized
More informationPOWER PRICE UNI. powerful UNF METAL. UNCPower UNIVERSAL TAPS. power ful. powerful TOP GEOMETRIES UNF PERFECT CHOICE VER UNIVERSAL TAPS SAL UNIVERSAL
MADE BY UNIVERSALtaps TOP QUALITY FROM GERMANY at a Power Price TOP GEOMETRIES FORM EUNIVERSAL UNIVERSAL TAPS powerful perfect UNF longideal flutes choice tool life PROCESS RELIABLE PERFECT Form universal
More informationChapter 23: Machining Processes: Hole Making Part A (Lathe Operations, Boring, Reaming, Tapping)
1 Manufacturing Processes (2), IE-352 Ahmed M El-Sherbeeny, PhD Spring 2017 Manufacturing Engineering Technology in SI Units, 6 th Edition Chapter 23: Machining Processes: Hole Making Part A (Lathe Operations,
More informationIndexable Center Drill
i-center indexable center drill (patent pending) First Indexable center drill in the world. Shortens set up time and center drilling time. Increases tool life which reduces tooling cost. Special forms
More informationProductivity, Creativity & Infinity
Productivity, Creativity & Infinity Nine9 company began in 1994 and with the development of special tools, boring heads and accessories. The Nine9 logo was commissioned in 1999. It comes from the Chinese
More informationVEX-S. Combination Drill with Front & Back Chamfering of Through Holes. tip combined with patented SNAP. chip control.
Combination Drill with Front & Back Chamfering of Through Holes tip combined with patented SNAP chip control blade replacement Cat. No. HTC015 Introduction Catalog HTC015No. HTC14 HEULE is setting new
More informationAUTOMOTIVE TAPPING ENGINEERED SOLUTIONS
AUTOMOTIVE TAPPING ENGINEERED SOLUTIONS Material: AlMgSi Alloys MINIMAL LUBRICATION FOR MAXIMUM RESULTS CARBIDE FORMING TAPS AL-IK Specially developed thread forming geometry and coating with the aid of
More informationFeatures. High Positive Rake Angle. Multi-Side Grinding. High Speed, High Feed Rate. Economical
Engraving This is a revolutionary new concept of engraving tools with indexable carbide inserts. They offer you the ability to produce HIGH QUAITY ENGRAVING in most materials. The latest coated carbide
More information5-axis clamping system compact
5-axis clamping system compact 395 5-axis clamping system compact Function We are setting standards with the new KIPP 5-axis clamping system compact in this field. The system was specifically designed
More informationFlexible tool overhang lengths possible by combining the modular extension arbor and shank with insert run-out adjustment mechanism
Sumi Easy insert replacement Characteristics Achieves efficiency through high speed, high feeding ability!! (v c =50 to 500m/min, f = 0.4 to 1.2mm/rev) Compatibility with a wide range of cutting conditions
More informationTooltech Precision Reamers are designed to meet hole geometry requirements in the complex and demanding machining environment of today s manufacturing
BLADED REAMERS Tooltech Precision Reamers are designed to meet hole geometry requirements in the complex and demanding machining environment of today s manufacturing industry. The innovative design of
More informationCARBIDE END MILLS SPECIFICATIONS
SPECIFICATIONS COATING GUIDE Material Hardness TiN TiCN TiALN Austentic Stainless Steel < 35 HRc * X Martinistic Stainless Steel < 35 HRc * X Martinistic Stainless Steel >= 35 HRc X PH Stainless Steel
More informationOptimum tool for finish machining
Series Expansion Indexable Ball-nose End Mill for Finishing Indexable Corner Radius End Mill for Finishing 2011.2 Update B065E SRF/SRB SUF High accuracy indexable end mill Optimum tool for finish machining
More informationLecture 15. Chapter 23 Machining Processes Used to Produce Round Shapes. Turning
Lecture 15 Chapter 23 Machining Processes Used to Produce Round Shapes Turning Turning part is rotating while it is being machined Typically performed on a lathe Turning produces straight, conical, curved,
More informationNC Spot Drill with Patented indexable carbide insert.
with Patented indexable carbide insert. High Efficiency! Low Cost! CNC Lathes, CNC Turning Centers and Machining Centers. One tool will perform multiple applications. Long tool life. Each insert has four
More informationEMCOMAT E-200 MC for the m cycle-controlled m
EMCOMAT E-200 MC for the m cycle-controlled m 1 HEADSTOCK Solid cast-iron construction Powerful Siemens drive system Short taper spindle nose with CAMLOCK adaptor Spindle bore diameter ø 53 (50) mm 2 2
More informationLightweight HSC milling cutter for a perfect surface finish. flycutter - system eco
Lightweight HSC milling cutter for a perfect surface finish flycutter - system eco 2 milling FlyCutter - System Eco mapal FlyCutter - System Eco The FlyCutter series represent a new dimension in face milling
More informationINSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS
INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. LA-Tool... 5 2.1 Technical Data... 5 2.2 Overview: Main Components...
More informationChapter 23: Machining Processes: Turning and Hole Making
Manufacturing Engineering Technology in SI Units, 6 th Edition Chapter 23: Machining Processes: Turning and Hole Making Chapter Outline 1. Introduction 2. The Turning Process 3. Lathes and Lathe Operations
More informationDRA DRA. MagicDrill. High Efficiency Modular Drill. Excellent hole accuracy with a low cutting force design. High Efficiency Modular Drill
High Efficiency Modular Drill High Efficiency Modular Drill MagicDrill DRA Excellent hole accuracy with a low cutting force design Optimal web thickness limits deflection Fine chip breaking and smooth
More information. Dimensions of Machine Spindle Heads in Compliance with DIN The most recent editions of the DIN standards are binding
ß Clamping tools. Dimensions of Machine Spindle Heads in Compliance with DIN The most recent editions of the DIN standards are binding DIN 5506 Taper sizes 4 and above with driver. Spindle No. of holes
More informationPCBN ball race milling cutters GUHRING - YOUR WORLD-WIDE PARTNER
The tooling concept of Guhring s ball race milling cutter is simple, practice orientated and highly accurate maximum rigidity and stability highest precision high process reliabiliy consistently high manufacturing
More informationCoroChuck 970 SynchroFlex Benefits
Benefits Better surface quality on the flanks of the cut threads Longer tool life due to less friction Greater process security Due to the reduced risk of breaking the tap especially with small dimensions
More informationMachining Strenx and Hardox. Drilling, countersinking, tapping, turning and milling
Machining and Drilling, countersinking, tapping, turning and milling and are registered trademarks. These steel grades are manufactured only by SSAB. high strength steel and wear plate are steel grades
More informationBSF. Large Ratio Automatic Back Counterboring & Spotfacing Tool
BSF Large Ratio Automatic Back Counterboring & Spotfacing Tool Counterbores up to 2.3xd Replaceable carbide coated blades for extended life Very simple to use Suitable for CNC machines with through coolant
More informationTechnical features. Positive Taper Lock System for manual tool clamping. Technical features:
clamping set Technical features The RÖHM- was specially designed for the positive taper lock clamping taking particulary into account the necessity of manual clamping. Technical features: strong design
More informationCost reduction Cost reduction Cost reduction
Cost reduction Quality, performance, value - Guaranteed! Work-Piece Cutting Speed vc(sfm) ISO Material Hardness (HB) Hardness (HRC) PC5300 PC5400 P Carbon steel C = 0.10-0.35% 80~180 10~ 459~886 328~820
More informationAutomotive solutions for ISO K
Automotive solutions for ISO K When machining in ISO K materials, you need tough tools that can withstand high abrasive wear and frittering, and deliver secure and precise machining again and again. This
More informationDrilling. Drilling is the operation of producing circular hole in the work-piece by using a rotating cutter called DRILL.
Drilling Machine Drilling Drilling is the operation of producing circular hole in the work-piece by using a rotating cutter called DRILL. The machine used for drilling is called drilling machine. The drilling
More informationThe new generation with system accessories. Made in Germany!
1 The new generation with system accessories. Made in Germany! For face, longitudinal and taper turning, thread-cutting. For machining steel, brass, aluminium and plastic. Mounting flange for fastening
More information. Dimensions of the Machine Spindle Heads in Compliance with DIN The most recent editions of the DIN standards are binding.
Clamping technology. Dimensions of the Machine Spindle Heads in Compliance with DIN The most recent editions of the DIN standards are binding. DIN 55026 Taper sizes 4 and above with drive tang. Spindle
More informationUNIT 4: (iii) Illustrate the general kinematic system of drilling machine and explain its working principle
UNIT 4: Drilling machines: Classification, constructional features, drilling & related operations, types of drill & drill bit nomenclature, drill materials. Instructional Objectives At the end of this
More informationTOP WORK ISO 9001.CE UNIVERSAL CUTTER & TOOL GRINDER
TOP WORK ISO 9001.CE UNIVERSAL CUTTER Precise ball groove of conformation Inclination of Wheelhead The wheelhead can easily tilt up to ±15 degrees, with a 360-degrees swivel on the horizontal plane. The
More informationBoring Milling. MAPAL competence Tools with ISO elements
Boring Milling MAPAL competence Tools with ISO elements Perfect machining technology MAPAL stands for innovative machining solutions with the highest quality, precision and cost-effectiveness. Starting
More informationUPDATED. PCD & CBN Tangential Milling. Features:
Diameters Metric: 5.0 mm 50 mm Inch:.0 0.0 Bodies Cylindrical Shell Type Integral on request UPDATED PCD & CBN Tangential Milling TEDIFEED is the newest line of mill with tangential inserts available with
More informationChapter 23 Drilling and Hole Making Processes. Materials Processing. Hole Making Processes. MET Manufacturing Processes
MET 33800 Manufacturing Processes Chapter 23 Drilling and Hole Making Processes Before you begin: Turn on the sound on your computer. There is audio to accompany this presentation. Materials Processing
More informationPremium Power Tool Accessories Proudly Made in the USA
Premium Power Tool Accessories Proudly Made Table of Contents Make it Snappy Tools Premium Power Tool Accessories Proudly Made About Us Founded in a basement machine shop in Minnesota in 1962, we are a
More informationBuild a Drill Press Vise
Youth Explore Trades Skills Introduction This activity plan will develop the student s machining and metalworking skills as they fabricate a multi-piece steel vise. The project will encompass basic lathe
More informationLathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY
TURNING MACHINES LATHE Introduction Lathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY - 1797 Types of Lathe Engine Lathe The most common form
More informationMEFA mounting accessories
MEFA mounting accessories Mounting accessories Base plates Page 5/2 Double holder Page 5/4 Height-adjustable suspensions Page 5/5 Pendular bolt joints Page 5/6 Trapeze hanger Page 5/7 Threaded hooks, distance
More informationEnd Mills 4. Cutting Tools 1 (Cont d) End-mills (Cont d)
Outline Review of Milling Cutting Tools Milling Milling Operations Workpiece Materials Tool Selection Machining Tips Toolholders Fixtures Cutting Tools HSS tools Coated (TiN, Al O 3, TiAlN,...) versions
More informationDeburring tools GUHRING YOUR WORLDWIDE PARTNER. EW 100 G Deburring fork EWR 500 Deburring reamer
EW 100 G Deburring fork EWR 500 Deburring reamer Chamfering milling cutter Front/back deburring mill Ball nose deburring mill EW Deburring reamer EWR 500 Deburring tools GURIG YOUR WORLDWIDE PARTER Deburring
More informationInstallation Tools. Pipe Cutters for steel and cast iron pipes 598. Deburring Reamer / for stainless steel pipes 600. for copper pipes 602
596 597 Installation Tools Pipe Cutters for steel and cast iron pipes 598 Pipe Cutters / Pipe Deburring Reamer for stainless steel pipes 600 Pipe Cutters / Pipe Deburring Reamer / Calibrating Tool for
More informationPSK Tool Holders. Chapter 2 of the Product Catalogue 2010/2011 Precision Tools
PSK Tool Holders Chapter 2 of the Product Catalogue 2010/2011 Precision Tools PSK - Polygonal Kelch GmbH Tel.: +49 (0) 71 51 / 2 05 22-0 Fax: +49 (0) 71 51 / 2 05 22-11 info@kelchgmbh.de www.kelchgmbh.de
More information