INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS

Size: px
Start display at page:

Download "INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS"

Transcription

1 INSTRUCTIONS FOR USE A1 & A2 KNURLING TOOLS

2 Contents CONTENTS 1. General Introduction Tool Construction A1-Tools Technical Data Overview: Main Components Tool Adjustment A1/KF Optical Measurement A1/KF Tool Adjustment A1/FL Optical Measurement A1/FL Adapter for long-turning lathes A2-Tools Technical Data Overview: Main Components Tool Adjustment A2/KF Optical Measurement A2/KF Tool Adjustment A2/FL Optical Measurement A2/FL Coolant Unit A1/A General Technical Data Overview: Main Components Assembly/Starting up Clean the Coolant Unit Subsequent Machining of Shank A Wear Parts Knurling of Stepped Workpieces Knurl Cutters with Bevel Troubleshooting Dimensions and Pitches Available Reference Values for Feeds and Cutting Speeds

3 General Introduction 1. General 1.1 Introduction Please read through the Instructions for Use carefully before using the Quick knurl cutting tools! The instructions have been written for operators with qualified training in the field of machining and cutting. Compliance with the Instructions for Use increases reliability in use, increases the service life of the tools, and prevents downtimes. We reserve the right to make alterations to the technical details of the tools by comparison with the information and illustrations contained in these Instructions for Use. Symbols in these instructions ATTENTION: This Symbol warns that operating procedures carried out without paying attention to the measures specified may lead to damage to the tool and/or the machine tool. NOTE: This Symbol refers to further information and provides additional information for using the Quick knurling tools. Text markups: This symbol identifies lists This symbol identifies an action sequence 2

4 1.2 Tool Construction A-series tools are flexible in use and may be employed on all lathes from the conventional to CNC-controlled dual-spindle lathes, optionally as a left-hand or right-hand tool, in front or behind the turning centre. The tools have a cutting action, are free-cutting and it is not possible to make them adopt a specific General Tool Construction speed ratio to the diameter of the workpiece by means of sustained forcing. As a result the number of teeth of the knurl produced may differ. The difference is approx. ± 1-3 teeth depending on the pitch. Type of knurl DIN 82 Tool Knurl cutters Straight knurl RAA A/FL 30 L /30 R Spiral knurl RBL / RBR A/FL As required Cross knurl RKE A/KF 15 L + 15 R Diamond knurl RGE A/KF 2 x 90 3

5 General Tool Construction Tool definition Definition of the tool as left- or right-handed is determined by the position of the knurl cutters when the tool is viewed from the front in the clamped position. left right left right Perfect results may be achieved with: Correct adjustment Closely following the instructions regarding the start of the knurling process Appropriate feed and cutting speed Selection of the correct tool size. Quick knurl cutter tools with large dimensioned knurl cutters, e.g. Ø 21.5 mm instead of Ø 14.5, have a longer service life Clamping Clamping of the holder on the shaft is effected by means of an eccentric chuck. The surface clamping generated as a result reduces the vibrations arising due to machining and increases the service life of the knurl cutters. Shafts and bodies may be individually assembled easily and without much effort by the customer himself. NOTE: It is imperative to ensure an abundant supply of coolant or cutting oil directly onto the knurl cutters to ensure perfect cooling and lubrication of the knurl cutters. 4

6 A1-Tools Technical Data 2. A1-Tools 2.1 Technical Data A1/KF Types of knurl Cross and diamond Working range Ø 3-50 mm Shaft dimension x16, 12x16 or 16x16 mm Knurl cutters Ø 14.5 mm Cross 1 x 15 L and 1 x 15 R Diamond 2 x 90 Pitches see page 40 Weight 0.3 kg /12/16 16 A1/FL Types of knurl Straight and spiral Working range Ø 3-50 mm Shaft dimension x16, 12x16 or 16x16 mm Knurl cutters Ø 14.5 mm Straight 1 x 30 L / 30 R Spiral As required Pitches see page 40 Weight 0.3 kg /12/

7 A1-Tools Overview: Main Components 2.2 Overview: Main Components Pos. Designation 1 Tool head 2 Countersunk screw 3 Washer 4 Knurl cutter 5 Bushing 6 Index disc (diameter adjustment) 7 Index point 8 Clamping segment 9 Shaft Eccentric bolt 11 Spindle screw A1/KF A1/FL Hexagonal socket head screws - tool correction (A1/FL) Adjustment gauge - A1/KF 14 Adjustment gauge - A1/FL

8 2.3 Tool Adjustment A1/KF Preliminary work: Clamp workpiece and turn Maximum out-of-roundness 0.03 mm Step 1: Cutter selection Cross knurl: 1x 15 left-hand spiral toothed knurl cutter on cutter holder "L" 1x 15 right-hand spiral toothed knurl cutter on cutter holder "R" Diamond knurl: 2x 90 toothed knurl cutters A1-Tools Tool Adjustment A1/KF Step 2: Install knurl cutters Clean the contact surface of bushing 5 and cutter holder 1.1. Coat bushing 5 and the face ends as well as the hole of knurl cutter 4 with a little Molykote G paste With knurl cutter 4 and washer 3 pushed on, insert bushing 5 into the cutter holder Screw in countersunk screw 2 and only tighten enough to allow knurl cutter 4 to rotate free of play

9 A1-Tools Tool Adjustment A1/KF Step 3: Pre-adjust turning centre For centring of the tool, the mark M on the shaft must be aligned with the mark on the head. The mark in the middle of the head should be selected for use in conventional machines. The outer marks should be selected for use in CNC machines depending on the shaft dimensions. Pos. Application Shaft 0 conventional /12/16 a CNC b CNC 12 c CNC 16 -a CNC -b CNC 12 -c CNC 16 c b a 0 -a -b -c M Adjustment: Unscrew eccentric bolt Adjust tool head 1 accordingly by way of spindle screw 11 Clamp eccentric bolt lightly

10 Step 4: Set diameter Measure off workpiece diameter Unscrew clamping segment 8 by two turns Turn index disc 6 until the required diameter aligns with index point 7 Only clamp clamping segment 8 lightly for subsequent adjustment of cutter 7 6 Step 5: Clamp tool in tool holder A1-Tools Tool Adjustment A1/KF Step 6: Re-align turning centre Carefully bring into contact with the workpiece Both cutters must be in contact simultaneously. Precision adjustment is carried out using spindle screw 11 Tighten eccentric bolt hand-tight when alignment is finished

11 A1-Tools Tool Adjustment A1/KF Step 7: Adjust cutter The ideal position of the knurling cutters is when they lie parallel on the workpiece and still cut very slightly, i.e. the cutting edge of the cutters can be pressed in somewhat deeper (approx. 1-2 ). In the case of materials which are hard to machine, the knurling cutters may be inclined up to max Step 8: Start of knurl Sequence: Adjust index disc 6 slightly towards the next smaller diameter until the correct cutter setting is reached Tighten clamping segment 8 The start of the knurl should be in a width no greater than 1.5 mm. With this width now move the tool to the full depth without interruption. The feed on infeeding should be approx mm. The knurling depth corresponds to the pitch of the knurling cutter being used, e.g. 1.0 mm pitch requires 1.0 mm infeed with reference to the diameter. The depth is measured from the knurling cutter's point of contact with the workpiece.

12 A1-Tools Tool Adjustment A1/KF After an idle time of 2-3 seconds, the workpiece is knurled by using the longitudinal feed. The surface deformation of the workpiece cannot be determined exactly as this is different from material to material. The knurling depth, however, should be sufficient to ensure that the knurl is only just sharp. max 1,5 mm NOTE: Note that the protective bevel at the beginning of the workpiece may not be applied until knurling is complete. The coarser the pitch, the smaller the feed. Feed and cutting speed have no effect on the knurl pitch. Step 9: Knurling NOTE: If the knurl is not accurate or is onesided, then the knurling process may be repeated after correcting the tool. ATTENTION: Under no circumstances knurl with longitudinal feed into the face edge of the workpiece. Starting the knurl within the workpiece can be done only in certain circumstances. 11

13 A1-Tools Optical Measurement A1/KF 2.4 Optical Measurement A1/KF The tool may be optically measured on the presetting device using adjustment gauge 13 supplied. 8 Dismantle knurl cutter 4 and bushing 5 Unscrew eccentric bolt and pre-set the turning centre by means of spindle screw z=0 x=0 Clamp eccentric bolt lightly 4 5 Push adjustment gauge 13 onto closed clamping segment 8 Precision adjust the turning centre under the pre-setting device, clamp eccentric bolt hand-tight and determine the X and Z values 11 The measured Z value is the start of the knurl not the collision measurement. The measured X value is adopted without a correction value for a workpiece diameter of 5 mm. The radius values shown in the table must be added to the X values depending on the workpiece diameter. With this measurement the knurl cutters are positioned approximately mm above the diameter to be knurled. Precise adjustment of the tool must be carried out on the machine. Ø X+ Ø X+ Ø X

14 2.5 Tool Adjustment A1/FL Preliminary work: Clamp workpiece and turn Maximum out-of-roundness 0.03 mm Step 1: Cutter selection Straight knurl - right-hand tool: 1x 30 right-hand spiral toothed knurl cutter Straight knurl - left-hand tool: 1x 30 left-hand spiral toothed knurl cutter NOTE: Right-hand tool requires the workpiece to rotate in a clockwise direction. Left-hand tool requires the workpiece to rotate in an anti-clockwise direction. A1-Tools Tool Adjustment A1/FL Step 2: Install knurl cutters Clean the contact surface of bushing 5 and cutter holder 1.1. Coat bushing 5 and the face ends as well as the hole of knurl cutter 4 with a little Molykote G paste With knurl cutter 4 and washer 3 pushed on, insert bushing 5 into the cutter holder Screw in countersunk screw 2 and only tighten enough to allow knurl cutter 4 to rotate free of play Spiral knurl: Knurl cutters are to be mounted with 15, 30 or 90 spirals depending on the pitch of the spiral desired on the workpiece. It is advisable due to the large number of possible variations to consult your dealer or the manufacturer. 13

15 A1-Tools Tool Adjustment A1/FL Step 3: Adjust turning centre For centring of the tool, the mark M on the shaft must be aligned with the mark on the head. The mark in the middle of the head should be selected for use in conventional machines. The outer marks should be selected for use in CNC machines depending on the shaft dimensions. c b a 0 -a -b -c M Pos. Application Shaft 0 conventional /12/16 a CNC b CNC 12 c CNC 16 -a CNC -b CNC 12 -c CNC 16 Adjustment: Unscrew eccentric bolt Adjust tool head 1accordingly by way of spindle screw 11 Clamp eccentric bolt again hand-tight NOTE: Precision adjustment of the turning centre can only be carried out on the optical pre-setting device. 14

16 Step 4: Clamp tool in tool holder Step 6: Start of knurl A1-Tools Tool Adjustment A1/FL Step 5: Adjust cutter The ideal position of the knurling cutters is when they lie parallel on the workpiece and still cut very slightly, i.e. the cutting edge of the cutters can be pressed in somewhat deeper (approx. 1-2 ). In the case of materials which are hard to machine, the knurling cutters may be inclined up to max The start of the knurl should be in a width no greater than 1.5 mm. With this width now move the tool to the full depth without interruption. The feed on infeeding should be approx mm. The knurling depth corresponds to the pitch of the knurling cutter being used, e.g. 1.0 mm pitch requires 1.0 mm infeed with reference to the diameter. The depth is measured from the knurling cutter's point of contact with the workpiece. After an idle time of 2-3 seconds, the workpiece is knurled by using the longitudinal feed. The surface deformation of the workpiece cannot be determined exactly as this is different from material to material. The knurling depth, however, should be sufficient to ensure that the knurl is only just sharp. max 1,5 mm Sequence: Correction is achieved by turning the tool slightly in the tool holder 15

17 A1-Tools Tool Adjustment A1/FL ATTENTION: Under no circumstances knurl with longitudinal feed into the face edge of the workpiece. Starting the knurl within the workpiece can be done only in certain circumstances. NOTE: Note that the protective bevel at the beginning of the workpiece may not be applied until knurling is complete. Step 7: Knurling If the track generated does not run paraxially, this may be put right by correcting the two hexagonal socket head screws 12. When adjusting by way of screw 12a, first loosen screw 12b and vice versa Tighten the opposing screw again hand-tight when adjustment is complete The coarser the pitch, the smaller the feed. Feed and cutting speed have no effect on the knurl pitch. 12a 12b NOTE: If the knurl is not accurate or is one-sided, then the knurling process may be repeated after correcting the tool. 16

18 2.6 Optical Measurement A1/FL The tool may be optically measured on the presetting device using adjustment gauge 14 supplied. Dismantle knurl cutter 4 and bushing 5 Unscrew eccentric bolt and adjust the turning centre by means of the spindle screw 11 Clamp eccentric bolt lightly again A1-Tools Optical Measurement A1/FL Mount adjustment gauge 14 on tool holder 1.1 Precision adjust the turning centre under the pre-setting device, clamp eccentric bolt hand-tight and determine the X and Z values z=0 x=0 11 The measured Z value is the start of the knurl not the collision measurement. If the measured X value is programmed, the knurl cutter is positioned approximately mm above the diameter to be knurled and precise adjustment of the tool must be carried out on the machine. 17

19 A1-Tools Adapter for long-turning lathes 2.7 Adapter for long-turning lathes A1 adapter for long turning lathes 15 may be mounted on appropriate A1 shaft 9 simply by means of the two screws 16. Retention in the machine is by means of the adapter. As a result the tool is aligned completely flush with the knurl cutters. Dimensions adapter for long-turning lathes A1/KF A1/FL 80 /12/ ,6 80 /12/16 18

20 A2-Tools Technical Data 3. A2-Tools 3.1 Technical Data A2/KF Types of knurl Cross and diamond Working range Ø mm Shaft dimension 20x25 or 25x25 mm Knurl cutters Ø 21.5 mm Cross 1 x 15 L and 1 x 15 R Diamond 2 x 90 Pitches see page 40 Weight 1.2 kg /25 25 A2/FL Types of knurl Straight and spiral Working range Ø mm Shaft dimension 20x25 or 25x25 mm Knurl cutters Ø 21.5 mm Straight 1 x 30 L / 30 R Spiral As required Pitches see page 40 Weight 1.0 kg /

21 A2-Tools Overview: Main Components 3.2 Overview: Main Components Pos. Designation 1 Tool head 2 Countersunk screw 3 Washer 4 Knurl cutters 5 Bushing 6 Index disc (diameter adjustment) 7 Index point 8 Clamping segment 9 Shaft Eccentric bolt 11 Spindle screw 12 Hexagonal socket head screws - tool correction (A2/FL) 13 Adjustment gauge - A2/KF 14 Adjustment gauge - A2/FL A2/KF A2/FL

22 3.3 Tool Adjustment A2/KF Preliminary work: Clamp workpiece and turn Maximum out-of-roundness 0.03 mm Step 1: Cutter selection Cross knurl: 1x 15 left-hand spiral toothed knurl cutter on cutter holder "L" 1x 15 right-hand spiral toothed knurl cutter on cutter holder "R" A2-Tools Tool Adjustment A2/KF Step 2: Install knurl cutters Clean the contact surface of bushing 5 and cutter holder 1.1. Coat bushing 5 and the face ends as well as the hole of knurl cutter 4 with a little Molykote G paste With knurl cutter 4 and washer 3 pushed on, insert bushing 5 into the cutter holder Screw in countersunk screw 2 and only tighten enough to allow knurl cutter 4 to rotate free of play Diamond knurl: 2x 90 toothed knurl cutters

23 A2-Tools Tool Adjustment A2/KF Step 3: Pre-adjust turning centre For centring of the tool, the mark M on the shaft must be aligned with the mark on the head. The mark in the middle of the head should be selected for use in conventional machines. The outer marks should be selected for use in CNC machines depending on the shaft dimensions. b a 0 -a -b M Pos. Application Shaft 0 conventional 20/25 a CNC 20 b CNC 25 -a CNC 20 -b CNC 25 Adjustment: Unscrew eccentric bolt Adjust tool head 1 accordingly by way of spindle screw 11 Clamp eccentric bolt lightly

24 A2-Tools Tool Adjustment A2/KF Step 4: Set diameter Measure off workpiece diameter Unscrew clamping segment 8 by two turns Turn index disc 6 until the required diameter aligns with index point 7 Only clamp clamping segment 8 lightly for subsequent adjustment of cutter 7 6 Step 5: Clamp tool in tool holder Step 6: Re-align turning centre Carefully bring into contact with the workpiece Both cutters must be in contact simultaneously. Precision adjustment is carried out using spindle screw 11 Tighten eccentric bolts hand-tight when alignment is finished

25 A2-Tools Tool Adjustment A2/KF Step 7: Adjust cutter The ideal position of the knurling cutters is when they lie parallel on the workpiece and still cut very slightly, i.e. the cutting edge of the cutters can be pressed in somewhat deeper (approx. 1-2 ). In the case of materials which are hard to machine, the knurling cutters may be inclined up to max Step 8: Start of knurl Sequence: Adjust index disc 6 slightly towards the next smaller diameter until the correct cutter setting is reached Tighten clamping segment 8 The start of the knurl should be in a width no greater than 1.5 mm. With this width now move the tool to the full depth without interruption. The feed on infeeding should be approx mm. The knurling depth corresponds to the pitch of the knurling cutter being used, e.g. 1.0 mm pitch requires 1.0 mm infeed with reference to the diameter. The depth is measured from the knurling cutter's point of contact with the workpiece. 24

26 A2-Tools Tool Adjustment A2/KF After an idle time of 2-3 seconds, the workpiece is knurled by using the longitudinal feed. The surface deformation of the workpiece cannot be determined exactly as this is different from material to material. The knurling depth, however, should be sufficient to ensure that the knurl is only just sharp. max 1,5 mm NOTE: Note that the protective bevel at the beginning of the workpiece may not be applied until knurling is complete. The coarser the pitch, the smaller the feed. Feed and cutting speed have no effect on the knurl pitch. ATTENTION: Under no circumstances knurl with longitudinal feed into the face edge of the workpiece. Starting the knurl within the workpiece can be done only in certain circumstances. Step 9: Knurling NOTE: If the knurl is not accurate or is onesided, then the knurling process may be repeated after correcting the tool. 25

27 A2-Tools Optical Measurement A2/KF 3.4 Optical Measurement A2/KF The tool may be optically measured on the presetting device using adjustment gauge 13 supplied. Dismantle knurl cutter 4 and bushing 5 Unscrew eccentric bolt and pre-set the turning centre by means of spindle screw z=0 x=0 Clamp eccentric bolt lightly Push adjustment gauge 13 onto closed clamping segment 8 Precision adjust the turning centre under the pre-setting device, clamp eccentric bolt hand-tight and determine the X and Z values 11 The measured Z value is the start of the knurl not the collision measurement. The measured X value is adopted without a correction value for a workpiece diameter of 8 mm The radius values shown in the table must be added to the X values depending on the workpiece diameter. With this measurement the knurl cutters are positioned approximately mm above the diameter to be knurled. Precise adjustment of the tool must be carried out on the machine. Ø X+ Ø X+ Ø X

28 3.5 Tool Adjustment A2/FL Preliminary work: Clamp workpiece and turn Maximum out-of-roundness 0.03 mm Step 1: Cutter selection Straight knurl - right-hand tool: 1x 30 right-hand spiral toothed knurl cutter Straight knurl - left-hand tool: 1x 30 left-hand spiral toothed knurl cutter NOTE: Right-hand tool requires the workpiece to rotate in a clockwise direction. Left-hand tool requires the workpiece to rotate in an anti-clockwise direction. A2-Tools Tool Adjustment A2/FL Step 2: Install knurl cutters Clean the contact surface of bushing 5 and cutter holder 1.1. Coat bushing 5 and the face ends as well as the hole of knurl cutter 4 with a little Molykote G paste With knurl cutter 4 and washer 3 pushed on, insert bushing 5 into the cutter holder Screw in countersunk screw 2 and only tighten enough to allow knurl cutter 4 to rotate free of play Spiral knurl: Knurl cutters are to be mounted with 15, 30 or 90 spirals depending on the pitch of the spiral desired on the workpiece. It is advisable due to the large number of possible variations to consult your dealer or the manufacturer. 27

29 A2-Tools Tool Adjustment A2/FL Step 3: Adjust turning centre For centring of the tool, the mark M on the shaft must be aligned with the mark on the head. The mark in the middle of the head should be selected for use in conventional machines. The outer marks should be selected for use in CNC machines depending on the shaft dimensions. Pos. Application Shaft 0 conventional 20/25 a CNC 20 b CNC 25 -a CNC 20 -b CNC 25 Adjustment: Unscrew eccentric bolt Adjust tool head 1 accordingly by way of spindle screw 11 Clamp eccentric bolt again hand-tight b a 0 -a -b M NOTE: Precision adjustment of the turning centre can only be carried out on the optical pre-setting device. 28

30 Step 4: Clamp tool in tool holder Step 6: Start of knurl A2-Tools Tool Adjustment A2/FL Step 5: Adjust cutter The ideal position of the knurling cutters is when they lie parallel on the workpiece and still cut very slightly, i.e. the cutting edge of the cutters can be pressed in somewhat deeper (approx. 1-2 ). In the case of materials which are hard to machine, the knurling cutters may be inclined up to max The start of the knurl should be in a width no greater than 1.5 mm. With this width now move the tool to the full depth without interruption. The feed on infeeding should be approx mm. The knurling depth corresponds to the pitch of the knurling cutter being used, e.g. 1.0 mm pitch requires 1.0 mm infeed with reference to the diameter. The depth is measured from the knurling cutter's point of contact with the workpiece. After an idle time of 2-3 seconds, the workpiece is knurled by using the longitudinal feed. The surface deformation of the workpiece cannot be determined exactly as this is different from material to material. The knurling depth, however, should be sufficient to ensure that the knurl is only just sharp. max 1,5 mm Sequence: Correction is achieved by turning the tool slightly in the tool holder 29

31 A2-Tools Tool Adjustment A2/FL ATTENTION: Under no circumstances knurl with longitudinal feed into the face edge of the workpiece. Starting the knurl within the workpiece can be done only in certain circumstances. NOTE: Note that the protective bevel at the beginning of the workpiece may not be applied until knurling is complete. Step 7: Knurling If the track generated does not run paraxially, this may be put right by correcting the two hexagonal socket head screws 12. When adjusting by way of screw 12a, first loosen screw 12b and vice versa Tighten the opposing screw again hand-tight when adjustment is complete The coarser the pitch, the smaller the feed. Feed and cutting speed have no effect on the knurl pitch. 12a 12b NOTE: If the knurl is not accurate or is onesided, then the knurling process may be repeated after correcting the tool. 30

32 3.6 Optical Measurement A2/FL The tool may be optically measured on the presetting device using adjustment gauge 14 supplied. Dismantle knurl cutter 4 and bushing 5 Unscrew eccentric bolt and adjust the turning centre by means of the spindle screw 11 Clamp eccentric bolt lightly again A2-Tools Optical Measurement A2/FL Mount adjustment gauge 14 on tool holder 1.1 Precision adjust the turning centre under the pre-setting device, clamp eccentric bolt hand-tight and determine the X and Z values z=0 x=0 The measured Z value is the start of the knurl not the collision measurement. If the measured X value is programmed, the knurl cutter is positioned approximately mm above the diameter to be knurled and precise adjustment of the tool must be carried out on the machine. 31

33 Coolant Unit A1/A2 General 4. Coolant Unit A1/A2 4.1 General This innovative cooling system enables targeted cooling and lubrication of the cutters or workpieces and thus increases the service life of the tools. Easy assembly and cleaning are further distinguishing features of the system. There are two versions available for A series knurling tools: Coolant unit with three adjustable ball nozzles for A/KF tools Coolant unit with a flat nozzle for A/FL tools 4.2 Technical Data Coolant pressure: max. 8 bar A A2 32 A1/A KF FL 32

34 4.3 Overview: Main Components Coolant Unit A1/A2 Overview: Main Components Pos. Description 1 Housing 2 Jet nozzle KF - 3 adjustable nozzles 3 Jet nozzle FL - flat nozzle 4 Gasket 5 Push-in connection 6 Blanking plug 7 Coolant hose 8 Cyl. head screw KF FL

35 Coolant Unit A1/A2 Assembly/Starting up 4.4 Assembly/Starting up NOTE: The illustration for the following work steps show the tool A1/KF with coolant unit KF. The same manner of proceeding also applies for the other tools of the A series. Step 1: Assembly Position coolant unit 1 with alignment pin on shank. Screw in cyl. head screw 8 and tighten handtight. Step 2: Connect coolant supply Clamp tool in tool holder Press top push-in connector 5 in slightly and feed in hose 7 until limit stop is reached. Route hose 7 with corresponding bending radius to connection on tool holder, cut to length as necessary and connect. Press push-in connector 5 in slightly at second coolant connection of coolant unit and insert blanking plug 6 until limit stop is reached

36 Step 3: Activate cooling system Activate the cooling system before commencing knurling ATTENTION: The coolant unit is designed for a max. pressure of 8 bar. Step 4: Precision adjustment of ball nozzles on coolant unit KF To ensure the best possible cooling for A/KF tools, direct the two outer nozzles onto the knurl cutters and the middle nozzle onto the workpiece Coolant Unit A1/A2 Clean the Coolant Unit 4.5 Clean the Coolant Unit Loosen coolant hose on tool holder Unscrew and remove cyl. head screw and detach coolant unit Press push-in connectors 5 slightly and detach coolant hose 7 as well as blanking plug

37 Coolant Unit A1/A2 Subsequent Machining of Shank A2 Unlatch mounting of nozzle insert 2 via the lateral slotted openings and pull out of housing 1 with gasket Subsequent Machining of Shank A2 No receiving holes were provided in models A2/KF and A2/FL prior to introduction of the coolant unit. The shanks have to be machined subsequently to retrofit the coolant unit. 1x threaded hole M4 1x slot with fit for alignment pin 33 +0,1 0 12,5 +0,05-0,05 6 4,5 Clean all parts in soap solution and rinse with clear water to remove microchips. Re-insert nozzle insert 2 with gasket 4 into housing 1 and fix with snap closure Assemble remaining parts and re-attach coolant unit to shank M ,1-0,1 4 H11 36

38 Wear Parts 5. Wear Parts The fixing elements for the knurl cutters of the QUICK A-series tools are wear parts and must be replaced frequently Knurling of Stepped Workpieces It must be noted that with all QUICK knurl cutting tools it is not possible to knurl right up to a shoulder due to the inclined position of the knurl cutters. Please refer to the table for dimensions. a b Pos. Designation 1 Countersunk screw 2 Washer 3 Bushing Distance b corresponds to the Ø of the knurl cutters Ø 14.5 Ø 21.5 Ø 14.5 Ø 21.5 a b b a b b

39 Knurl Cutters with Bevel 7. Knurl Cutters with Bevel A knurl cutter's teeth may break off when knurling "hard" materials. It is possible to increase the knurl cutter's service life by cutting a 45 bevel. This is only applicable for the KF models. Arrangement for cutters with bevel Only one knurl cutter 4 with bevel may be used depending on the direction in which the workpiece rotates. 0,5xt 4 45 t 4 38

40 Troubleshooting 8. Troubleshooting A/KF Tools Knurl trailing spirally Look at start of knurl Look at knurling depth Tool tilted sideways -> check position Clearance of tool too positive or too negative Overlapping of the knurl (double knurl) Incorrect adjustment of diameter Approach to knurl depth too slow as a result of which too little guidance of knurl cutters in track Look at start of knurl Teeth of knurl cutters knocked off Bevel knurl cutters with hard materials Knurl cutter has been overloaded too much feed, cutting depth too great Incorrect adjustment of diameter Fixing screws of knurl cutters loose Look at adjustment of cutters Unevenly deep knurl track Re-align position of head using spindle Seizing of knurl cutters on bushing (see A/FL) A/FL Tools Knurl trailing spirally Correct position of head using precision adjustment screws Look at start of knurl Look at knurling depth Tool tilted sideways -> check position Clearance of tool too positive or too negative Overlapping of the knurl (double knurl) Approach to knurl depth too slow as a result of which too little guidance of knurl cutters in track Look at start of knurl Teeth of knurl cutters knocked off Knurl cutter has been overloaded feed too great, cutting depth too great Fixing screws of knurl cutters loose Look at direction of rotation Look at adjustment of cutters Seizing of knurl cutters on bushing Reduce cutting speed Use Molykote paste Coolant jet directly onto the knurl cutter 39

41 Dimensions and Pitches Available 9. Dimensions and Pitches Available Technical Description Material: Powder metallurgy tool steel Heat treatment: Hardened to HRC Models: Ground or ground + coated with Q-Dur Dimensions and pitches t Order numbers and designation Ident. no. Ø A Ø B C Ø Tooth pitch angle Pitches (t) toothed 0.4/0.5/0.6/0.8/1.0/ L/15 R toothed 0.4/0.5/0.6/0.8/1.0/ L/30 R toothed 0.4/0.5/0.6/0.8/1.0/ toothed 15 L/15 R toothed 30 L/30 R toothed 0.4/0.5/0.6/0.8/1.0/ 1.2/1.5/1.6/ /0.5/0.6/0.8/1.0/ 1.2/1.5/1.6/ /0.5/0.6/0.8/1.0/ 1.2/1.5/1.6/2.0 Pos. Description 1 Production date MM/YY 2 Tooth pitch angle 3 Tooth pitch direction R (right) L (left) 4 Tooth pitch 5 Material 6 Tooth tip angle 7 Production process G (ground) / M (milled) 8 Coated with QDUR / TiCN / TIN 40

42 Reference Values for Feeds and Cutting Speeds. Reference Values for Feeds and Cutting Speeds Workpiece Ø 3-12 Material Cutter Ø V s m/min mm/rev Workpiece Ø V s m/min mm/rev Steel up to 600 N/mm² V m/min Workpiece Ø s mm/rev Steel up to 900 N/mm² Stainless steels Ms Ms

43 Reference Values for Feeds and Cutting Speeds Workpiece Ø 3-12 Material Cutter Ø V s m/min mm/rev Workpiece Ø V s m/min mm/rev Bronze V m/min Workpiece Ø s mm/rev Aluminium Grey cast iron Cast steel NOTE: Generally speaking the values applicable to aluminium are also valid for plastics. Test runs are imperative. 42

44 QUICK Tooling GmbH Brunnenstraße Aldingen Germany Tel.: Fax: / Edition. Technical details are subject to change. Printing errors excepted. No part of these document may be copied or disclosed for any purposes without the written approval of QUICK Tooling GmbH. All rights reserved.

INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL

INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL INSTRUCTIONS FOR USE B2 FORM KNURLING TOOL Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. B2 Tools... 6 2.1 Technical Data... 6 2.2 Overview: Main components... 7

More information

INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS

INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS INSTRUCTIONS FOR USE LA, MAMMUT & STR KNURLING TOOLS Contents CONTENTS 1. General... 2 1.1 Introduction... 2 1.2 Tool Construction... 3 2. LA-Tool... 5 2.1 Technical Data... 5 2.2 Overview: Main Components...

More information

NEW RÄNDELFRÄSWERKZEUGE KNURLINGTOOLS

NEW RÄNDELFRÄSWERKZEUGE KNURLINGTOOLS NEW RÄNDELFRÄSWERKZEUGE KNURLINGTOOLS KNURLING TOOLS Swarovski Optik KG Swarovskistraße 70 A-6067 Absam Fon +43 (0)5223 511-0 Fax +43 (0)5223 511-6550 info@quick-tools.at www.quick-tools.at Milled knurls

More information

Precision made in Germany. As per DIN The heart of a system, versatile and expandable.

Precision made in Germany. As per DIN The heart of a system, versatile and expandable. 1 Precision made in Germany. As per DIN 8606. The heart of a system, versatile and expandable. Main switch with auto-start protection and emergency off. Precision lathe chuck as per DIN 6386 (Ø 100mm).

More information

March weeks. surcharge for

March weeks. surcharge for March weeks valid until 31.03.2012 all quoted prices are incl. 19% VAT for deliveries in the EU countries to customers with a valid VAT-no. and for deliveries in not EU member countries the VAT is not

More information

no mm no Dividers with scriber 150 mm NEW Square wedge-shaped knife edges on the length side

no mm no Dividers with scriber 150 mm NEW Square wedge-shaped knife edges on the length side Summer Promotion valid until 30.06.2013 all quoted prices are incl. VAT for deliveries to EU countries to customers with valid VAT-no. and for deliveries in non EU member countries the VAT is not applicable

More information

Clamping devices 521

Clamping devices 521 Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps

More information

The new generation with system accessories. Made in Germany!

The new generation with system accessories. Made in Germany! 1 The new generation with system accessories. Made in Germany! For face, longitudinal and taper turning, thread-cutting. For machining steel, brass, aluminium and plastic. Mounting flange for fastening

More information

Technical T-A & GEN2 T-A GEN3SYS APX. Revolution & Core Drill. ASC 320 Solid Carbide. AccuPort 432. Page CONTENTS. Set-up Instructions 256

Technical T-A & GEN2 T-A GEN3SYS APX. Revolution & Core Drill. ASC 320 Solid Carbide. AccuPort 432. Page CONTENTS. Set-up Instructions 256 Technical ASC 0 Solid Carbide CONTENTS Page Set-up Instructions 6 AccuPort 4 Recommended Speeds & Feeds 60 Guaranteed Application Request Form 99 +44 (0)84 400 900 +44 (0)84 400 0 enquiries@alliedmaxcut.com

More information

PUNCHING DRILLING HEBEN LIFTING CUTTING DEBURRING

PUNCHING DRILLING HEBEN LIFTING CUTTING DEBURRING PUNCHING DRILLING LIFTING CUTTING DEBURRING www.alfra.de E-EN E ALFRA Edge-Milling and Deburring Devices Overview KFV KFH 150 Page 7 78 2520 25100 Prism mounting L = 150 / W = 20/40 End mill Ø 45 or straight

More information

The new generation with system accessories. Made in Europe!

The new generation with system accessories. Made in Europe! 1 The new generation with system accessories. Made in Europe! Of cast iron, wide-legged prismatic guide. For vibration-free work even at high loads. Rear flange for mounting the mill/drill head PF 230.

More information

Screws. Introduction. 1. Nuts, bolts and screws used to clamp things together. Screws are used for two purposes:

Screws. Introduction. 1. Nuts, bolts and screws used to clamp things together. Screws are used for two purposes: Screws Introduction Screws are used for two purposes: 1. To clamp things together. 2. To control motion. 1. Nuts, bolts and screws used to clamp things together. Nuts, bolts and screws that are used for

More information

Competence Gun Boring. KOYEMANN Floating Tools Power Reamer

Competence Gun Boring. KOYEMANN Floating Tools Power Reamer Competence Gun Boring KOYEMANN Floating Tools Power Reamer R The KOYEMANN Floating Principle Reaming has been used for fine machining bores with excellent results from the very start of cutting technology.

More information

OPERATING INSTRUCTIONS 5-AXIS CLAMPING SYSTEM + ACCESSORIES

OPERATING INSTRUCTIONS 5-AXIS CLAMPING SYSTEM + ACCESSORIES OPERATING INSTRUCTIONS 5-AXIS CLAMPING SYSTEM + ACCESSORIES 1 Contents 1. Introduction 2. Safety instructions and precautions 3 Operating the clamp 3.1 Clamp set up 3.2 Sequence for clamp set up 3.3 Adjusting

More information

Ensat driving tools...

Ensat driving tools... nsat driving tools... On this page, you can configure the optimum tool for your application. A configuration is provided in the following as an illustrative example. The article number is composed of two

More information

Operating instruction for the quick-change tap holders type:

Operating instruction for the quick-change tap holders type: type: KSN 0 KSN 1 KSN 3 KSN 4 KSN 5 Date of edition: 01.02.2008 Stage of alteration: 1 Please keep this for future use! Contents: 1 Application range, safety instructions and technical data... 3 1.1 Application

More information

VARIABLE SPEED WOOD LATHE

VARIABLE SPEED WOOD LATHE MODEL MC1100B VARIABLE SPEED WOOD LATHE INSTRUCTION MANUAL Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference. Version: 2015.02.02

More information

zeus KNURLING TECHNOLOGY --> KNURLING WHEELS --> FORM KNURLING TOOLS --> CUT KNURLING TOOLS --> SPECIAL TOOLS

zeus KNURLING TECHNOLOGY --> KNURLING WHEELS --> FORM KNURLING TOOLS --> CUT KNURLING TOOLS --> SPECIAL TOOLS zeus KNURLING TECHNOLOGY --> KNURLING WHEELS --> FORM KNURLING TOOLS --> CUT KNURLING TOOLS --> SPECIAL TOOLS TECHNOLOGY. SERVICE. PASSION. WELCOME TO HOMMEL+KELLER PRÄZISIONSWERKZEUGE! We work with enthusiasm

More information

» Modular clamping elements for optical or optical/tactical measurement» For high-precision edge measurements in reflected and transmitted light

» Modular clamping elements for optical or optical/tactical measurement» For high-precision edge measurements in reflected and transmitted light » Modular clamping elements for optical or optical/tactical measurement» For highprecision edge measurements in reflected and transmitted light» Toothed rails as workpiece stops or for fastening clamping

More information

Our aim is to offer all our customers an optimal level of product benefits, product advice and customer service.

Our aim is to offer all our customers an optimal level of product benefits, product advice and customer service. Knurling Technology The Company 2 The company Hommel + Keller was founded in 1926 by the precision technician Jakob Keller and his business partner Georg Hommel. During the first years of its operation,

More information

Typical Parts Made with These Processes

Typical Parts Made with These Processes Turning Typical Parts Made with These Processes Machine Components Engine Blocks and Heads Parts with Complex Shapes Parts with Close Tolerances Externally and Internally Threaded Parts Products and Parts

More information

Special reamers. Figure N 1 Reamer with descending cutting edges in carbide (Cerin)

Special reamers. Figure N 1 Reamer with descending cutting edges in carbide (Cerin) Special reamers There is a wide category of special reamers, ie non-standard, that are suitable to address particular problems encountered in the finishing holes, both for maintenance of individual pieces

More information

5-axis clamping system compact

5-axis clamping system compact 5-axis clamping system compact 395 5-axis clamping system compact Function We are setting standards with the new KIPP 5-axis clamping system compact in this field. The system was specifically designed

More information

The new generation with system accessories. Made in Germany!

The new generation with system accessories. Made in Germany! 1 The new generation with system accessories. Made in Germany! For face, longitudinal and taper turning, thread-cutting. For machining steel, brass, aluminium and plastic. Mounting flange for fastening

More information

Operating instructions. Fine boring head Ø3-88 with digital display

Operating instructions. Fine boring head Ø3-88 with digital display Operating instructions Fine boring head Ø3-88 with digital display English 1. Basic safety information Before first use, please read the operating instructions carefully. These provide important safety

More information

CNC milling machines. Pocket milling. Milling of segments into a drive wheel. Milling of the outer contour

CNC milling machines. Pocket milling. Milling of segments into a drive wheel. Milling of the outer contour CNC milling machines You want to mill with precision! WABECO CNC milling machines guarantee you the ultimate precision covering the entire working range of the machine. Production in Germany on state-of-the-art

More information

-Eagle Edger Jr Linear Edge Add-on for the Blue Ripper Jr

-Eagle Edger Jr Linear Edge Add-on for the Blue Ripper Jr -Eagle Edger Jr Linear Edge Add-on for the Blue Ripper Jr (Blade shown might not ship with tool, or be available.) Operation, Safety, and Instruction Manual v20150521 Page 2 Operating/Safety Instructions

More information

The Ensat self-tapping threaded insert...

The Ensat self-tapping threaded insert... The nsat self-tapping threaded insert... nsat is a self-tapping threaded insert with external and internal thread, cutting slots or cutting bores. A continuous process of further development has brought

More information

Tool & Cutter Grinder

Tool & Cutter Grinder Tool & Cutter Grinder The Bonelle Tool and Cutter grinder (based on prof. Chaddock s Quorn) can be used to grind most kind of tools from lathe tools to end-mills and reamers. I have been grinding my end-mills

More information

BSF. Large Ratio Automatic Back Counterboring & Spotfacing Tool

BSF. Large Ratio Automatic Back Counterboring & Spotfacing Tool BSF Large Ratio Automatic Back Counterboring & Spotfacing Tool Counterbores up to 2.3xd Replaceable carbide coated blades for extended life Very simple to use Suitable for CNC machines with through coolant

More information

400 SERIES GRINDER PUMPS 41502, 42202,43302, AND MODELS

400 SERIES GRINDER PUMPS 41502, 42202,43302, AND MODELS Section: MOYNO 500 PUMPS Page: 1 of 6 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 400 SERIES GRINDER PUMPS 41502, 42202,43302, AND 44402 MODELS DESIGN FEATURES Housing: Cast iron Pump Rotor: Chrome

More information

Adjusting Backlash on Sherline handwheels

Adjusting Backlash on Sherline handwheels WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING Adjusting Backlash on Sherline handwheels What Is Backlash? Backlash is the amount the handwheel can turn before

More information

Operating Manual. for CUTTING, PERFORATING, BENDING SLB120

Operating Manual. for CUTTING, PERFORATING, BENDING SLB120 Operating Manual for CUTTING, PERFORATING, BENDING SLB120 31040\B06eng 0896 0 Contents 1. Scope of delivery... 1 2. Technical specifications... 1 3. Applications... 1 4. Commissioning... 2 5. Cutting...

More information

2.0. Contents Function control

2.0. Contents Function control Contents 2.0 Drill bits 2.1 Medullary reamer heads 2.2 Burrs 2.3 Bone taps 2.4 Drill sleeves with serrated ends 2.5 Drill guides for plates 2.6 Aiming device 2.7 Pointed drill guide 2.8 Quick coupling

More information

SERVICE INSTRUCTIONS :

SERVICE INSTRUCTIONS : 1 HAROLD HABEGGER SA TÉL. ++41 32 497 97 55 INTERNET: www.habegger-sa.com FABRIQUE DE MACHINES FAX ++41 32 497 93 08 E-MAIL: contact@habegger-sa.com OUTILLAGE ROUTE DE CHALUET 5/9 CH-2738 COURT (SUISSE)

More information

Quick Set Dovetail Jig

Quick Set Dovetail Jig Quick Set Dovetail Jig FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CALL OUR CUSTOMER SERVICE HELP LINE : 01509 500359 THE MANUFACTURER RESERVES THE RIGHT TO ALTER THE DESIGN OR SPECIFICATION TO THIS PRODUCT

More information

Operating instructions. Twin cutter boring head Ø mm

Operating instructions. Twin cutter boring head Ø mm Operating instructions Twin cutter boring head Ø23.5-153.0 mm English 1. Basic safety information Before first use, please read the operating instructions carefully. These provide important safety information

More information

MINI-LATHE QUICK CHANGE TOOL POST

MINI-LATHE QUICK CHANGE TOOL POST MINI-LATHE QUICK CHANGE TOOL POST Cutting and assembly details Machinists should familiarize themselves with the contents of this section before jumping in to the drawings. Many details are described here

More information

Features. Special forms are possible

Features. Special forms are possible Center Drill >> The is a trademark of Nine9, the developer of the first indexable center drill in the world.(patented) Offering an indexable insert system for the 1st time, Nine9 s design improves your

More information

Diamond Burnishing Tools

Diamond Burnishing Tools Diamond Burnishing Tools www.cogsdill.co.uk Diamond burnishing Overview The Cogsdill Diamond Burnishing Tool is designed to produce high quality, low microinch burnished finishes on shafts, large bores,

More information

Single MJ Splitter Installation Manual - 1Si

Single MJ Splitter Installation Manual - 1Si SP1 Single MJ Splitter Installation Manual - 1Si Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719, USA. Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2004 Micro

More information

Tooltech Precision Reamers are designed to meet hole geometry requirements in the complex and demanding machining environment of today s manufacturing

Tooltech Precision Reamers are designed to meet hole geometry requirements in the complex and demanding machining environment of today s manufacturing BLADED REAMERS Tooltech Precision Reamers are designed to meet hole geometry requirements in the complex and demanding machining environment of today s manufacturing industry. The innovative design of

More information

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extention Sections. Reliable Connections insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extention 2-3 Improved Fire Hydrant Inserting Extention

More information

Useful accessories for lathe and milling systems.

Useful accessories for lathe and milling systems. 1 Useful accessories for lathe and milling systems. Nearly all accessories are supplied in wooden boxes. For proper and value preserving storage! Dividing attachment TA 250 For precision lathe PD 250/E,

More information

Technical features. Positive Taper Lock System for manual tool clamping. Technical features:

Technical features. Positive Taper Lock System for manual tool clamping. Technical features: clamping set Technical features The RÖHM- was specially designed for the positive taper lock clamping taking particulary into account the necessity of manual clamping. Technical features: strong design

More information

Indexable Center Drill

Indexable Center Drill i-center indexable center drill (patent pending) First Indexable center drill in the world. Shortens set up time and center drilling time. Increases tool life which reduces tooling cost. Special forms

More information

User s Guide. Silent Tools. turning products

User s Guide. Silent Tools. turning products User s Guide Silent Tools turning products Introduction This guide will help you to use dampened boring bars (Silent Tools) to achieve the best possible results in internal turning. Silent Tools dampened

More information

Quick-Release Front Vise 05G34.01

Quick-Release Front Vise 05G34.01 Quick-Release Front Vise 05G34.01 Patent Pending Introduction A front vise is the most generally useful vise on a typical workbench. It can be used for clamping parts on edge within the jaws, for clamping

More information

Operating Instructions. Universal drilling and milling machines with linear guideways

Operating Instructions. Universal drilling and milling machines with linear guideways Operating Instructions Universal drilling and milling machines with linear guideways F1410 LF F1410 LF high speed CC-F1410 LF CC-F1410 LF high speed Walter Blombach GmbH Tool and Machine Factory D-42899

More information

Quick-Release Sliding Tail Vise 05G30.01

Quick-Release Sliding Tail Vise 05G30.01 Quick-Release Sliding Tail Vise 05G30.01 U.S. Des. Pat. No. D671,812 U.S. Pat. No. 9,050,710 Introduction The Veritas Quick-Release Sliding Tail Vise is a reworked version of the well-known tail vise that

More information

52/8 04/2005 UNIVERSAL. Narrow Stitching Head. Operating-Instructions Spare parts list

52/8 04/2005 UNIVERSAL. Narrow Stitching Head. Operating-Instructions Spare parts list Operating-Instructions Spare parts list UNIVERSAL 52/8 04/2005 Narrow Stitching Head hohner Maschinenbau GmbH Gänsäcker 19, 78532 Tuttlingen, Telephone 07462 / 9468-0, Fax 07462 / 9468-20 hohner Maschinenbau

More information

Horizontal and Vertical. Metal Cutting Band Saw MODEL: BS-115

Horizontal and Vertical. Metal Cutting Band Saw MODEL: BS-115 Horizontal and Vertical Metal Cutting Band Saw MODEL: BS-5 SAFETY. Know your band saw. Read the operator s Manual carefully. Learn the operations, applications and limitation.. Use recommended accessories.

More information

ROTARY TABLE OPERATION AND SERVICE MANUAL HORIZONTAL AND VERTICAL. Horizontal & Vertical. Rotary Table (HVRT) Tilting Rotary Table

ROTARY TABLE OPERATION AND SERVICE MANUAL HORIZONTAL AND VERTICAL. Horizontal & Vertical. Rotary Table (HVRT) Tilting Rotary Table Horizontal & Vertical Rotary Table (HVRT) OPERATION AND SERVICE MANUAL Tilting Rotary Table Horizontal & Vertical Rapid Indexer VERTICAL AND HORIZONTAL ROTARY TABLE This Horizontal & vertical table is

More information

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots.

SAFETY INSTRUCTIONS. Wear protective clothing, including safety glasses and steel toe boots. SAFETY INSTRUCTIONS Wear protective clothing, including safety glasses and steel toe boots. DO NOT allow loose clothing or long hair near machine operations. Keep work site and machine clean. Use brush

More information

Machining Strenx and Hardox. Drilling, countersinking, tapping, turning and milling

Machining Strenx and Hardox. Drilling, countersinking, tapping, turning and milling Machining and Drilling, countersinking, tapping, turning and milling and are registered trademarks. These steel grades are manufactured only by SSAB. high strength steel and wear plate are steel grades

More information

Back-Spotfacing. Flipcut For back-spotfacing and backor front-chamfering operations from one side, in one set-up. Back-Spotfacing. & Chamfering TOOLS

Back-Spotfacing. Flipcut For back-spotfacing and backor front-chamfering operations from one side, in one set-up. Back-Spotfacing. & Chamfering TOOLS COGSDILL TOOL PRODUCTS, INC. Flipcut For back-spotfacing and backor front-chamfering operations from one side, in one set-up. Back-Spotfacing & Chamfering TOOLS Back-Spotfacing Available from stock for

More information

FBX1104P FBX1104 FBX1106P FBX1106

FBX1104P FBX1104 FBX1106P FBX1106 FBX1104P FBX1104 FBX1106P FBX1106 Second edition : September 2004 No. 040037 INTRODUCTION Thank you for your purchasing Kansai Special's FBX Series. Read and study this instruction manual carefully before

More information

Top spin Nr /

Top spin Nr / Top spin Nr. 1840 0000 / 1840 1000 Bedienungsanleitung 21-6680 28052014 / A Made in Germany Ideas for dental technology Top spin Nr. 1840 0000 / 1840 1000 Contents 1. Introduction...2 1.1 Symbols...2 2.

More information

Pull-down clamps. No Low height clamping jaws, model Bulle

Pull-down clamps. No Low height clamping jaws, model Bulle Pull-down clamps The wedge action of clamping jaws is the characteristic feature of these pull down clamps. It causes the pull down effect, which presses the workpiece against both, stop and machine table.

More information

Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX

Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX Installation Instructions 4 ft Antennas (with E-Mount) DA, DAX, UA, UDA, UXA SD, SDX, SU, SUX NMT 553-01(e) These Installation Instructions are valid for antennas in the following version : Reflector Ø

More information

STAMPING TECHNOLOGY - CLAMPING RAW PARTS

STAMPING TECHNOLOGY - CLAMPING RAW PARTS simple. gripping. future. 5-Axis 66 Makro Grip Stamping Unit 72 Stamping Unit for the workbench 73 Stamping Unit on trolley 76 Stamping Unit Accessories 77 Stamping Jaws 78 Makro Grip 5-Axis-Vices 82 5-Axis

More information

Clock 35 - Toyland. Construction instructions for Clock 35

Clock 35 - Toyland. Construction instructions for Clock 35 This clock has been designed for children, it is a stand-alone unit and can be positioned on a shelf or cabinet out of the reach of very young hands who may be tempted to touch. The clock is shown in two

More information

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections

MUELLER. Improved, Centurion Series, Modern Improved, and 107. Fire Hydrants. Inserting Extension Sections. Reliable Connections insertion Instructions manual MUELLER Improved, Centurion Series, Modern Improved, and 107 table of contents PAGE Centurion Series Fire Hydrant Adding an Extension 2-3 Improved Fire Hydrant Inserting Extension

More information

Lathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY

Lathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY TURNING MACHINES LATHE Introduction Lathe is a machine, which removes the metal from a piece of work to the required shape & size HENRY MAUDSLAY - 1797 Types of Lathe Engine Lathe The most common form

More information

-treme thread cutting. Tiny Tools. New Products. Metric

-treme thread cutting. Tiny Tools. New Products. Metric TM -treme thread cutting Tiny Tools New Products Metric 2014-2015 Tiny Tools Broaching Tools for Hexagon Keys - HK The HK broaching system have been developed to machine internal keyways inside blind or

More information

INNOVATIONS. KNIPEX Siphon and Connector Pliers. Exclusively distributed by MADE IN GERMANY

INNOVATIONS. KNIPEX Siphon and Connector Pliers. Exclusively distributed by MADE IN GERMANY MADE IN GERMANY INNOVATIONS KNIPEX Siphon and Connector Pliers For siphons, tube fittings and connectors up to 80mm diameter Fine adjustment for ideal adjustment to diverse diameters Robust, heavy duty

More information

OPERATING INSTRUCTIONS MODULGRAV. Tel. +49 (0) Fax +49 (0) homepage:

OPERATING INSTRUCTIONS MODULGRAV. Tel. +49 (0) Fax +49 (0) homepage: OPERATING INSTRUCTIONS MODULGRAV Kolpingstraße -7 D-784 Singen / Htwl. Postfach 80 D-784 Singen / Htwl. Tel. +49 (0) 77 88-0 Fax +49 (0) 77 88 66 e-mail: info@elma-ultrasonic.com homepage: www.elma-ultrasonic.com

More information

Installation and Operational Instructions for ROBA -DS couplings Type 95. _ (disk pack HF) Sizes

Installation and Operational Instructions for ROBA -DS couplings Type 95. _ (disk pack HF) Sizes 95. _ (disk pack HF) Sizes 6 22 Please read these Operational Instructions carefully and follow them accordingly! Ignoring these Instructions may lead to malfunctions or to coupling failure, resulting

More information

Assembly and Adjusting Instructions for Modules 6x6 and 4x4 Alignment Adapter

Assembly and Adjusting Instructions for Modules 6x6 and 4x4 Alignment Adapter Translated version of the instructions Version: 11/2017 SAP no.: 400151427 Assembly and Adjusting Instructions for Modules 6x6 and 4x4 Alignment Adapter The document was prepared by Gühring KG. All rights

More information

MANUFACTURING TECHNOLOGY

MANUFACTURING TECHNOLOGY MANUFACTURING TECHNOLOGY UNIT V Machine Tools Milling cutters Classification of milling cutters according to their design HSS cutters: Many cutters like end mills, slitting cutters, slab cutters, angular

More information

PRO System with Dedicated Automatic Kerf Keeper Installation Manual - SP-2 (V1.0) 0706

PRO System with Dedicated Automatic Kerf Keeper Installation Manual - SP-2 (V1.0) 0706 SP2 Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719, USA. Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2006 Micro Jig, Inc. MJ Splitter PRO System with Dedicated

More information

Question Bank Technical Drawing Metal

Question Bank Technical Drawing Metal Question Bank Technical Drawing Metal Table of Contents Question Bank Technical Drawing Metal...1 ASSEMBLY DRAWINGS & DETAILS...1 READING OF DRAWINGS...38 VIEWS...61 MACHINE ELEMENTS...87 i ii Question

More information

OWNER S MANUAL. Safety. Please read this owner s manual before use and keep it at hand for reference. Warranty

OWNER S MANUAL. Safety. Please read this owner s manual before use and keep it at hand for reference. Warranty Please read this owner s manual before use and keep it at hand for reference. OWNER S MANUAL Safety Important safety instructions for using the INCRA Miter5000 Before using the INCRA Miter5000, read and

More information

Operator s Guide. Sequin Device. Version 1.3. Published by: ZSK Stickmaschinen GmbH - Dokumentation - D Krefeld-Gartenstadt

Operator s Guide. Sequin Device. Version 1.3. Published by: ZSK Stickmaschinen GmbH - Dokumentation - D Krefeld-Gartenstadt Operator s Guide Sequin Device Version 1.3 Published by: ZSK Stickmaschinen GmbH - Dokumentation - D-47800 Krefeld-Gartenstadt Magdeburger Str. 38 40 04 by ZSK, Printed in Germany Subject to change. 04

More information

Tuf-Lite III Fans 5000K Series Hub

Tuf-Lite III Fans 5000K Series Hub Tuf-Lite III Fans 5000K Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 20 thru 30 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced

More information

(Fig 1) Column to Base 1. Place Column (7) on the Base (13) and align holes in the Column with holes in the Base. 2. Attach using Bolt Washer and Spring Washer hole through the Column and into the Base.

More information

192 Series Precision Involute Knurl / Spline Tools. Instruction Manual

192 Series Precision Involute Knurl / Spline Tools. Instruction Manual 192 Series Precision Involute Knurl / Spline Tools Instruction Manual Table of Contents Introduction... 3 What is an Involute Knurl or Spline?... 3 Why Roll Involute Knurl Connections?... 3 Why Use a CJWinter

More information

FBX-PA-2AC. Third edition : April No

FBX-PA-2AC. Third edition : April No FBX-PA-2AC Third edition : April 2006 No. 060058 INTRODUCTION Thank you very much for purchasing Kansai Special FBX series. Read and study this Instruction Manual carefully before you start any of the

More information

THE FUTURE RIGHT NOW PRECISION lathes, drilling- and milling machines

THE FUTURE RIGHT NOW PRECISION lathes, drilling- and milling machines THE FUTURE RIGHT NOW PRECISION lathes, drilling- and milling machines turning milling drilling WABECO lathes > D2000 D2400 D3000 precise lead screw lathe in-house design and production the classics - tried

More information

model tsa-sa48 Sliding Crosscut Table installation guide

model tsa-sa48 Sliding Crosscut Table installation guide model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop

More information

Operating instruction for the quick-change adapters type:

Operating instruction for the quick-change adapters type: type: EM 00 - U EM 01 - U EM 03 - U EM 04 - U EM 05 - U EM 01 U / IKZ EM 03 U / IKZ EM 04 U / IKZ EM 05 U / IKZ Date of edition: 01.02.2008 Stage of alteration: 2 Please keep this for future use! Contents:

More information

Tuf-Lite III Fans 5000K Series Hub

Tuf-Lite III Fans 5000K Series Hub Tuf-Lite III Fans 5000K Series Hub INSTALLATION MANUAL Hudson Tuf-Lite III fan blades Adjustable Pitch Fan Assembly 20 thru 30 Diameter Hudson Tuf-Lite III fan blades are of single piece fiberglass reinforced

More information

S-85SCH

S-85SCH 4411-4423-4432-4443-4452 5511-5523-5532-5554 44S-85SCH Service Manual 104 73 14-26 2014-02-24 CONTENTS 1. Names of principal parts...2 2. Removing methods of external parts 2-1 Sewing table...3 2-2 Face

More information

Compatibility overview of accessories for lathe

Compatibility overview of accessories for lathe Compatibility overview of accessories for lathe Accessory parts for turning Face clamping disc Ø 170 mm 3440295 Face clamping disc Ø 240 mm 3441352 Face clamping disc Ø 250 mm 3440552 Face clamping disc

More information

External Turning. Outline Review of Turning. Cutters for Turning Centers

External Turning. Outline Review of Turning. Cutters for Turning Centers Outline Review of Turning External Turning 3 External Turning Parameters Cutting Tools Inserts Toolholders Machining Operations Roughing Finishing General Recommendations Turning Calculations Machining

More information

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions

Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions Motorized M3 AX7200 Rotary-Style Gasket Cutter Operating Instructions INTRODUCTION Congratulations! You are the owner of the finest rotary-style gasket cutter in the world. Originally developed and patented

More information

Zero Point Clamping System. ZERO lock BALL lock

Zero Point Clamping System. ZERO lock BALL lock Zero Point Clamping System ZERO lock BALL lock kap3 kap 263 Technical information regarding ZERO lock Zero Point Clamping System Application The modularly designed, flexible ZERO lock Zero-Point Clamping

More information

Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2

Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2 TOOLS Page Q 2 Drilling machine Drilling machine for under pressure drilling Page Q 2/1 Motorised drilling machine Page Q 2/2 Page Q 3 Changeable carbide drill (WHM) Page Q 3/1 Drilling machine Tonisco

More information

MS25 OPERATION MANUAL

MS25 OPERATION MANUAL SAFETY INSTRUCTIONS SPECIFICATIONS OPERATING INSTRUCTIONS MAINTENANCE ADJUSTMENTS REPLACEMENT OF PARTS MS25 DIAGRAM MS25 PARTS LIST MS25 OPERATION MANUAL SAFETY INSTRUCTIONS Please read these instructions

More information

Machining. Drilling Countersinking Tapping Turning Milling

Machining. Drilling Countersinking Tapping Turning Milling Machining Drilling Countersinking Tapping Turning Milling hardox and weldox are registered trademarks.these steel grades are manufactured only by SSAB Oxelösund AB. hardox wear plate and weldox extra-high

More information

Limit switch set BOA-H DN PN 16/25 Material variant EN-GJS LT

Limit switch set BOA-H DN PN 16/25 Material variant EN-GJS LT Assembly instructions 0570.812/04-EN Limit switch set BOA-H DN 15-150 PN 16/25 Material variant EN-GJS-400-18-LT Fig. 1 Exploded view of limit switch set... 2 Fig. 2 Parts list for limit switch set...

More information

Operation Manual Cut-off Tool Holder BMT (external and internal coolant)

Operation Manual Cut-off Tool Holder BMT (external and internal coolant) Operation Manual Cut-off Tool Holder BMT (external and internal coolant) -1ESA Eppinger GmbH Breitwiesenweg 2-8 D-73770 Denkendorf +49 (0)711 934 934-0 info@eppinger.de www.eppinger.de 1. Name 2. Product

More information

TOOLS/PROCESSING SERVICES TOOLS + PROCESSING SERVICES

TOOLS/PROCESSING SERVICES TOOLS + PROCESSING SERVICES TOOLS/PROCESSING SERVICES 7 TOOLS + PROCESSING SERVICES MINITEC PROFILE SYSTEM 583 TOOLS/PROCESSING SERVICES TOOLS s l oot TOOLS 584 MINITEC PROFILE SYSTEM BALL-HEADED KEY - Chrome plated, with handle

More information

New type of broaching system

New type of broaching system New type of broaching system The construction of mechanical parts, even simple ones, sometimes involves difficult problems that require, for their resolution, lengthy times or the use of special machines.

More information

Trade of Toolmaking Module 2: Turning Unit 3: Drilling, Reaming & Tapping Phase 2

Trade of Toolmaking Module 2: Turning Unit 3: Drilling, Reaming & Tapping Phase 2 Trade of Toolmaking Module 2: Turning Unit 3: Drilling, Reaming & Tapping Phase 2 Published by SOLAS 2014 Unit 3 1 Table of Contents Document Release History... 3 Unit Objective... 4 Introduction... 4

More information

MODEL 7000 BEVEL-MILL

MODEL 7000 BEVEL-MILL MODEL 7000 BEVEL-MILL HECK INDUSTRIES P.O. BOX 425 HARTLAND, MI 48353 TOLL FREE: 800-886-5418 PHONE: 810-632-5400 FAX: 810-632-6640 WWW.HECKIND.NET INSTRUCTION MANUAL Save This Manual You will need the

More information

Maintenance Information

Maintenance Information 16601023 Edition 2 January 2014 Air Impact Wrench 2705P1 Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these

More information

Operator's manual. TruTool TKF 1500 (1A1), (1B1)

Operator's manual. TruTool TKF 1500 (1A1), (1B1) Operator's manual TruTool TKF 1500 (1A1), (1B1) Table of contents 1 Safety 4 1.1 General safety information 4 1.2 Specific safety information for beveler 4 2 Description 6 2.1 Intended use 6 2.2 Technical

More information

DICTATOR RTS Tube Door Closer

DICTATOR RTS Tube Door Closer Tube Door Closer RTS v long DICTATOR RTS Tube Door Closer The "Invisible" Door Closer The DICTATOR RTS tube door closer is built into the door and therefore is as good as invisible. The joint can only

More information

Pipe Cutting and Beveling Machines GF 4 (AVM/MVM) Training. precision. power. simplicity.

Pipe Cutting and Beveling Machines GF 4 (AVM/MVM) Training. precision. power. simplicity. precision. power. simplicity. Pipe Cutting and Beveling Machines GF 4 (AVM/MVM) Training Ehemals / formerly known as Georg Fischer Rohrverbindungstechnik Content 1 Basics 3 2 Range of application 11 3

More information