MAB25 ANGULAR SENSOR HALL EFFECT. The sensors of the MAB25 series use the magnetic technology to measure a rotation angle.

Transcription

1 MAB25 The sensors of the MAB25 series use the magnetic technology to measure a rotation angle. The axis pulls a magnet. The angular position of the magnetic field is measured by an HALL Effect sensor. The absolute angular position is then transmit by one of the threes bus available. ANGULAR SENSOR HALL EFFECT Infiniturn sensor , 12 or 14 bit Output by Bus serial, SPI, SSI

2 sf_mab25_1401_e04 - Document & produit soumis à modifications sans préavis. Pin assignment SSI Interface SPI Interface (galvanically isolated, redundant sections) SER Interface D- Data - Section 1 GND Ground D+ Data + SS1 Slave Select 1 DO Data C- Clock- SCLK1 Clock 1 CLK Clock C+ Clock+ MOSI1 Data Bi-dir 1 CSN Slave Select GND Ground GND1 Ground 1 +5V (+3V3) Supply Voltage VSUP Supply Voltage VDD1 Supply Voltage 1 Section 2 VDD2 Supply Voltage 2 GND2 Ground 2 MOSI2 Data Bi-Dir 2 SCLK2 Clock 2 SS2 Slave Select 2

3 Electrical Data SSI SPI SER Electrical Angle Independent linearity tolerance ± 0.4% ± 0.3% ± 0.4 % (12 bits) ± 0.5% (10 bits) Resolution 4096 steps (12 bits) steps (14 bits) 4096 steps(12 bits) 1024 steps (10 bits) Update rate 0.1 ms 2.5ms / 0.6 ms (High speed) 0.38 ms / 0.1 ms (High speed) Supply voltage 5 VDC±10% / VDC 5 VDC ± 10% 3.3 VDC ± 10% 5 VDC ± 10% Supply current (no load) <20mA <10mA (<20mA High speed) <20 ma Mechanical Data Maximum rotational speed Life time Operational torque < 3000 rpm > revolutions(depend on the application), tested with room temperature and 1N radial load < 1 Nm Environmental specifications Protection class IP40 Working temperature C Storage temperature C Bearings Polymer sleeve bearing Housing Polyamide strengthen glass-fiber (Nylon 66/30%GF) Shaft Stainless steel Mounting parts (Included in delivery) Hex nut (SW14), toothed washer Weight Approx. 20 g

4 SPI interface Description At left, the microprocessor, at right the MAB25 sensor Choose preferably a µprocessor equipt by a SPI interface. Nevertheless it can be emulated by an open collector. The datas transmission can be done on only one pin because there is not simultaneity : Host : 2 octets 0xAA 0xFF MAB25 : 2 octets of data follow by 2 octets of invert data Host: 4 octets 0xFF SSI interface Description

5 The SSI interface is largely used in industrials applications, particularly in absolute position sensors. Moreover it present a high immunity against electromagnetic interferencies because of the transmission by differential pairs. SER interface description

6 Order code Sensor simple output Sensor double output Resolution SER interface 10 bits 12 bits 10 bits High Speed 12 bits High Speed Resolution SSI interface 12 bits 12 bits High Speed MAB25 MAB25X HS 12HS 12 12HS Resolution SPI interface 14 bits 14 Supply/ Output signal 3v3 / SER (CW only) 5V / SER (CW only) 5V / SSI 15-30VDC / SSI 5V / SPI (double) Run & Direction of the change CW : clockwise direction CCW anti clockwise direction Standard : clockwise 360 3,3SER 5SER 5SSI 24SSI 5SPI Options CWxxx CCWxxx For double output version, indicate the direction of variation for the two outputs. Zero location C(C)Wxxx/C(C)Wxxx N Standard example MAB SSI 12 bits, power supply 5V, SSI interface, CW rotation on 360 Example with options MAB25X 14 5SPI CW360/CCW360 N 14 bits, power supply 5V, SPI interface, output 1 on 360 CW, output 2 on 360 ccw, 0 point alignment Clockwise rotation (CW) means that the output signal rise when the shaft is rotated in clockwise direction. It is a front view below. The output voltage equal 0 when the flat is on the pin, in case you choose the N option. Otherwise the 0 is not located..