Page 4-6. STAR-DELTA STARTERS OPEN FRAME Suitable for three-phase motor control, 16A...690A 440V / 7.5kW...375kW 400V ratings in IEC AC3 duty.

Transcription

1 Page -2 Page - DIRECT-ON-LINE STARTERS Motor ratings up to 9A 0V in IEC AC duty General use up to 6A / motor rating up to 2A 600V per UL/CSA Versions with Start-Stop/Reset buttons or Reset button Versions with and without thermal relay Versions with motor protection circuit breaker. REVERSING CONTACTOR ASSEMBLIES For three-phase motor control 9...2A 0V /...2.kW 00V, in IEC AC duty and up to HP 600V per UL/CSA Versions with built-in or external mechanical interlock Complete with rigid connections PCB version 9A 0V / kw 00V in IEC AC duty; HP 00V per UL/CSA. Page - CHANGEOVER CONTACTOR ASSEMBLIES For 20A loads at 0 C in IEC AC duty For 20A general use per UL/CSA With built-in mechanical interlock. Page -6 STAR-DELTA STARTERS OPEN FRAME Suitable for three-phase motor control, 6A...690A 0V / 7.kW...7kW 00V ratings in IEC AC duty. Page -7 STAR-DELTA STARTERS IN NON-METALLIC ENCLOSURE Suitable for three-phase motor control, A 0V / 7.kW...0kW 00V ratings in IEC AC duty. Page -8 EMPTY NON-METALLIC ENCLOSURES Versions without pushbuttons, with Reset button only or Start-Stop/Reset buttons For starters, with pushbuttons and metal plate Suitable to contain BG mini-contactor or BF09A to BF0 contactors, up to 0A 0V rating in IEC AC duty; up to 2A at 600V for UL/CSA.

2 ELECTROMECHANICAL STARTERS AND ENCLOSURES Direct-on-line starters in non-metallic enclosure complete with or without thermal relay Versions with RESET or START/STOP pushbuttons Non-metallic enclosures for customer-assembled starters Reversing and changeover contactor assemblies Star-delta starters, open frame and in non-metallic enclosure versions. Direct-on-line starters - Full voltage across the line - Non reversing SEC. - PAGE Enclosed with thermal relay Enclosed without thermal relay... - Enclosed with motor protection circuit breaker... - Combinations Reversing contactor assemblies With BG series mini-contactors... - With BF series contactors... - Changeover contactor assemblies With BG series mini-contactors... - Star-delta starters Open frame Enclosed Non-metallic enclosure for starters Empty non-metallic enclosures Enclosures Accessories and spare parts Combinations MOTOR CONTROL AND PROTECTION

3 Direct-on-line starters - Full voltage across the line. Non reversing three phase Enclosed with thermal overload relay M0 P...2 M P...2 M2 P...2 M2 P08 2 M2 R08 2 M P...2 M0 R...2 M R...2 M2 R...2 Order code Relay IEC technical Qty Wt adj characteristics per range ( 0V) pkg Ie kw [A] [A] [kw] n [kg] Starters with Start and Stop/Reset pushbuttons ❷. M0 P009 2❶ M0 P009 2❶V M0 P009 2❶2V M0 P009 2❶ M0 P009 2❶ M0 P009 2❶ M0 P009 2❶ M0 P02 2❶ M P009 2❶A M P009 2❶A M P009 2❶A M P009 2❶A M P009 2❶A M P009 2❶A M P009 2❶B M P08 2❶B M2 P02 2❶B M2 P02 2❶B M2 P02 2❶B M2 P08 2❶B M P00 2❶B M P06 2❶B M P080 2❶B M P09 2❶B Starters with Reset pushbuttons ❷. M0 R009 2❶ M0 R009 2❶V M0 R009 2❶2V M0 R009 2❶ M0 R009 2❶ M0 R009 2❶ M0 R009 2❶ M0 R02 2❶ M R009 2❶A M R009 2❶A M R009 2❶A M R009 2❶A M R009 2❶A M R009 2❶A M R009 2❶B M R08 2❶B M2 R02 2❶B M2 R02 2❶B M2 R02 2❶B M2 R08 2❶B M R00 2❶B M R06 2❶B M R080 2❶B M R09 2❶B ❶ Complete order code with coil voltage digit (if 0/60Hz) or with voltage digit followed by 60 (if 60Hz). Standard voltages are as follows: -- AC 0/60Hz 02 / 08 / 0 / 20 / 00V -- AC 60Hz / / / / / / 7 60 (V). Example: M0 R for direct-on-line starter in M0 type enclosure with Reset button, 9A/AC contactor with 2VAC 0/60Hz coil and 0.6-A thermal overload relay. M0 P for direct-on-line starter in M0 type enclosure with Start and Stop/Reset buttons, 9A /AC contactor with 2VAC 60Hz coil and 0.6-A thermal overload relay. ❷ Protection fuses are to be mounted externally by the user. Components Starter enclosure Contactor Thermal Auxiliary relay contact block M0 PA BG09 0A RF9 M0 PA BG09 0A RF9 V M0 PA BG09 0A RF9 2V M0 PA BG09 0A RF9 M0 PA BG09 0A RF9 M0 PA BG09 0A RF9 7 M0 PA BG09 0A RF9 0 M0 PA BG2 0A RF9 M PA BF09 0A RF8 000 M PA BF09 0A RF8 060 M PA BF09 0A RF8 020 M PA BF09 0A RF8 000 M PA BF09 0A RF8 060 M PA BF09 0A RF8 000 M PA BF09 0A RF8 00 M PA BF8 0A RF8 800 M2 PA BF2 0A RF8 200 M2 PA BF2 0A RF8 200 M2 PA BF2 00A RF8 200 G8 0 M2 PA BF8 00A RF8 800 G8 0 M PA BF0 00A RF G8 0 M PA BF6 00A RF G8 0 M PA BF80 00A RF G8 0 M PA BF9 00 RF9 9 G8 0 M0 RA BG09 0A RF9 M0 RA BG09 0A RF9 V M0 RA BG09 0A RF9 2V M0 RA BG09 0A RF9 M0 RA BG09 0A RF9 M0 RA BG09 0A RF9 7 M0 RA BG09 0A RF9 0 M0 RA BG2 0A RF9 M RA BF09 0A RF8 000 M RA BF09 0A RF8 060 M RA BF09 0A RF8 020 M RA BF09 0A RF8 000 M RA BF09 0A RF8 060 M RA BF09 0A RF8 000 M RA BF09 0A RF8 00 M RA BF8 0A RF8 800 M2 RA BF2 0A RF8 200 M2 RA BF2 0A RF8 200 M2 RA BF2 00A RF8 200 G8 0 M2 RA BF8 00A RF8 800 G8 0 M RA BF0 00A RF G8 0 M RA BF6 00A RF G8 0 M RA BF80 00A RF G8 0 M RA BF9 00 RF9 9 G8 0 Certifications and compliance Refer to page - for details. Special M... versions Refer to page - for details. UL/CSA HP ratings See page -2. M R Combinations pages -0 to pages -6 and 7 page -20

4 Direct-on-line starters - Full voltage across the line. Non reversing three phase Enclosed without thermal overload relay Order code Maximum operating Qty Wt current ( 0V) per pkg [A] n [kg] Starters with Start and Stop/Reset pushbuttons ❷. M0 P009 0❶ M0 P02 0❶ Components Starter enclosure Contactor Thermal Auxiliary standard standard relay to contact supplied supplied purchase standard separately supplied M0 PA BG09 0A RF9❸ M0 PA BG2 0A RF9❸ M0 P...0 M0 R...0 M P009 0❶ 0.90 M P08 0❶ M PA BF09 0A RF8❹ M PA BF8 0A RF8❹ M2 P02 0❶ M2 P02 0❶ 2.62 M2 PA BF2 0A RF8❹ M2 PA BF2 00A RF8❹ G8 0 M2 P08 0❶ M2 PA BF8 00A RF8❹ G8 0 M P...0 M R...0 M P00 0❶ 0.0 M P06 0❶ 6.0 M P080 0❶ 80.0 M P09 0❶ 9.0 Starters with Reset pushbutton ❷. M0 R009 0❶ M0 R02 0❶ M PA BF0 00A RF82❺ G8 0 M PA BF6 00A RF82❺ G8 0 M PA BF80 00A RF82❺ G8 0 M PA BF9 00 RF9 ❺ G8 0 M0 RA BG09 0A RF9❸ M0 RA BG2 0A RF9❸ M2 P...0 M2 R...0 M R009 0❶ M R08 0❶ M RA BF09 0A RF8❹ M RA BF8 0A RF8❹ M2 R02 0❶ M2 R02 0❶ 2.0 M2 RA BF2 0A RF8❹ M2 RA BF2 00A RF8❹ G8 0 M2 R08 0❶ M2 RA BF8 00A RF8❹ G8 0 M2 P08 0 M2 R08 0 M R00 0❶ M R06 0❶ M R080 0❶ M R09 0❶ ❶ Complete order code with coil voltage digit if 0/60Hz or with voltage digit followed by 60 if 60Hz. Standard voltages are as follows: -- AC 0/60Hz 02 / 08 / 0 / 20 / 00V -- AC 60Hz / / / / / / 7 60 (V). Example: M0 R for direct-on-line starter in M0 type enclosure with Reset button, 9A /AC contactor with 2VAC 0/60Hz coil. M0 P for direct-on-line starter in M0 type enclosure with Start and Stop/Reset buttons, 9A /AC contactor with 2VAC 60Hz coil. ❷ Protection fuses are to be mounted externally by the user. M RA BF0 00A RF82❺ G8 0 M RA BF6 00A RF82❺ G8 0 M RA BF80 00A RF82❺ G8 0 M RA BF9 00 RF9 ❺ G8 0 ❸ For thermal overload relay selection, refer to pages -2 or -. ❹ For thermal overload relay selection, refer to pages -. ❺ For thermal overload relay selection, refer to pages - or -. Operational characteristics Cable entry: M0/M - 2 knockouts PG./M20 on enclosure top and bottom M2-2 knockouts PG./M20 or PG6/M2 on enclosure top and bottom M2-2 knockouts PG6/M2-PG29/M2 on enclosure top and bottom M - Smooth surfaces; can be drilled by customer Ambient conditions: Operating temperature: C Storage temperature: C Degree of protection: IP6 for all; type /X industrial control environment for M / M2 / M2... and M... UL versions. M P...0 Special M... versions In addition to standard-indicated versions, culus certified starters are available up to 2A motor control or 6A general use rating max. Add suffix UL to the order code, e.g. M P UL. UL/CSA HP ratings See page -2. M R...0 Certifications and compliance Certifications obtained: EAC for all; UL Listed for USA and Canada (culus File E9602) and CSA certified for Canada and USA (ccsaus File 97) as Magnetic Motor Controllers, enclosed type, for all M0-M-M2- M2P/R starters and MP/R0-6 UL types as indicated in Special M above. Compliant with standards: IEC/EN 6097-, IEC/EN , UL08, CSA C22.2 n. Combinations pages -0 to pages -6 and 7 page -20 -

5 Direct-on-line starters Full voltage across the line. Non reversing three phase Enclosed with motor protection circuit breaker M2 P Order code Relay IEC technical Qty Wt adj characteristics per range ( 0V) pkg Ie kw [A] [A] [kw] n [kg] M2 P009 ❶A M2 P009 ❶A M2 P009 ❶A M2 P009 ❶A M2 P009 ❶A M2 P009 ❶A M2 P009 ❶B ❶ Complete order code with coil voltage digit (if 0/60Hz) or with voltage digit followed by 60 (if 60Hz). Standard voltages are as follows: -- AC 0/60Hz 02 / 08 / 0 / 20 / 00V -- AC 60Hz / / / / / / 7 60 (V). Example: M2 P A8 for direct-on-line starter in M2 type with reset and reset/emergency button, 9A/AC contactor with 00VAC 0/60Hz coil and motor protection circuit breaker...6.a. General characteristics The M2 P starters are composed of an IP6 plastic enclosure where the following devices are mounted: a motor protection circuit breaker type SMR... with the short circuit and overload protection function a contactor with start / stop function of the motor 2 push-buttons for the start and stop a mushroom push-button for the emergency stop a padlockable rotary actuator, that operates the circuit breaker, for the isolation. These starters are easily and quickly installable. They are especially suitable to operate the motor of smaller machines where there is no electrical panel. Inside the enclosure, other components can be added like timers, level relays, protection relays, etc. Operational characteristics M2-2 knockouts PG./M20 or PG6/M2 on enclosure top and bottom Ambient conditions: Operating temperature: C Storage temperature: C Degrre of protection: IEC IP6, type /X for UL version. Certifications and compliance Certifications obtained: EAC. Compliant with standards: IEC/EN 6097-, IEC/EN Combinations pages -0 to pages -6 page -20

6 Reversing and changeover contactor assemblies Reversing contactor assemblies BGR... BFA... BGT... BGTP... Changeover contactor assemblies BGC09... Order code IEC Max. IEC Built-in Qty Wt Ie (AC) power auxiliary per 0V AC contacts pkg C 00V at C [A] [kw] NO NC n [kg] AC COIL. Terminals: clamp screw. External interlock with power and auxiliary wiring. BGR09 0 A❶ 9 0 ❸ 0.9 BGR2 0 A❶ ❸ 0.9 BFA009 2❶ ❸ BFA02 2❶ ❸ BFA08 2❶ ❸ BFA02 2❶ ❸ Built-in interlock with power wiring only. BGT09 0 A❶ 9 ❸ BGT2 0 A❶ 2.7 ❸ Rear terminals: PCB solder pins. Built-in interlock only. BGTP09 0 A❶ 9 ❹ 0 ❸ 0.00 DC COIL. Terminals: clamp screw. External interlock with power and auxiliary wiring. BGR09 0 D❷ 9 0 ❸ 0.60 BGR2 0 D❷ ❸ 0.60 Built-in interlock with power wiring only. BGT09 0 D❷ 9 ❸ 0 0. BGT2 0 D❷ 2.7 ❸ 0 0. Rear terminals: PCB solder pins. Built-in interlock only. BGTP09 0 D❷ 9 ❹ 0 ❸ 0.60 Order code IEC Operating UL/CSA Qty Wt current (AC) General per Use pkg 0 C C 60 C [A] [A] [A] [A] n [kg] AC COIL. Terminals: clamp screw. Built-in interlock only. BGC09 T A❶ DC COIL. Terminals: clamp screw. Built-in interlock only. BGC09 T D❷ ❶ Complete order code with coil voltage digit or with voltage digit followed by 60 if 60Hz. Standard voltages are as follows: -- AC 0/60Hz 02 / 08 / 0 / 20 / 00V -- AC 60Hz / / / / / / 7 60 (V). Example: BGR09 0 A02 for reversing contactor assembly with 2 mini-contactors BG09 having NC auxiliary contact each and 2VAC 0/60Hz coil. BGR09 0 A02 60 for reversing contactor assembly with 2 mini-contactors BG09 having NC auxiliary contact each and 2VAC 60Hz coil. ❷ Complete order code with coil voltage digit. Standard voltages are: -- DC 02 / 02 / 08 / 060 / 0 / 2 / 220V. Example: BGC09 T D02 is a changeover contactor assembly with 2 mini-contactors BG09 having main poles each and 2VDC coil. ❸ One auxiliary contact for each contactor. ❹ Maximum voltage is limited at 00V for UL. For certified type up to 600V, consult Customer Service; see contact details on front inside cover. General characteristics REVERSING CONTACTOR ASSEMBLIES Supplied complete, ready for quick mounting. The various versions are composed as follows: BGR... Screw termination, external mechanical BGT... interlock BGX0 00, power and auxiliary wiring. Screw termination, built-in mechanical interlock and power wiring only. BGTP... Rear PCB solder pin termination, built-in mechanical interlock only. No thermal overload relay can be directly mounted to BG... reversing contactor assemblies. BFA... Screw termination, mechanical interlock BFX0 02 and power wiring. The thermal overload relay RF8... can be directly mounted to BFA... reversing contactor assemblies; for selection, refer to section. CHANGEOVER CONTACTOR ASSEMBLIES Supplied complete, ready for quick mounting as follows: BGC09 T Four-pole contactors with built-in mechanical interlock. No power or auxiliary wiring included. Operational characteristics Type Maximum IEC operational power at C (AC) 20V 00V V 0V 00V 690V [kw] [kw] [kw] [kw] [kw] [kw] BGR BGT BGTP09❹ BGR BGT BFA BFA BFA BFA at 0 C (AC) BGC09 T Maximum UL/CSA horsepower rating Single phase Three phase 20V 20V 208V 20V 80V 600V [HP] [HP] [HP] [HP] [HP] [HP] BGR09 ½ ½ 2 BGT09 ½ ½ 2 BGTP09 ½ ½ 2 ❹ -❹ BGR2 ½ ½ 7½ 0 BGT2 ½ ½ 7½ 0 BFA009 ¾ 2 7½ BFA02 2 7½ 0 BFA08 0 BFA02 2 7½ 7½ NOTE: BGR09, BGT09, BGR2, BGT2 types are UL Listed for USA and Canada as Magnetic Motor Controller Reversing Contactors. All these are rated 20A general (purpose) use and suitable for use on a circuit capable of delivering more than ka symmetrical. Amps at 600V max when protected by fuses class K rated no more than 0A. BGTP09 type is UL Recognized for USA and Canada as Magnetic Motor Controller Component reversing contactors. Max HP rating up to 00VAC only; rated 20A general (purpose) use. BGC types are UL Listed for USA and Canada as Magnetic Motor Controller Changeover contactor. No coil change or replacement is possible for any BG types. Add-on blocks Refer to section 2, pages 2-6 and 2-8. Special add-on auxiliary contacts BGX or BGX 2 must be used on the left-side contactor of the BGT reversing assemblies. For the right-side contactor, normal BGX0... types of auxiliary contacts can be used instead. Refer to page 2-6 for details. Certifications and compliance Certifications obtained: UL Listed for USA and Canada (File E9602) for BGR09, BGT09, BGR2, BGT2, BFA... and BGC... (see NOTE above). UL Recognized, for USA and Canada (culus - File E9602 Component), for BGTP09; products having this type of marking are intended for use as components of complete workshop-assembled equipment. Compliant with standards IEC/EN 6097-, IEC/EN , UL08, CSA C22.2 n. Add-on blocks pages 2-6 and 2-7 pages -7 and 8 page -20 Technical characteristics pages 2-8 to

7 Star-delta starters Open frame Order code Three-phase Thermal Qty Wt BFA009...BFA02 motor control. overload per Max IEC relay operating pkg current ( 0V) [A] n [kg] Complete star-delta starters, open frame, for starting time up to 2s and a maximum of 0 operations/hour. BFA009 70❶❷ 6 No.700 BFA02 70❶❷ 22 No.700 BFA08 70❶❷ 28 No.700 BFA02 70❶❷ No.800 BFA026 70❶❷ No.800 BFA02 70❶❷ 0 No.900 BFA08 70❶❷ 60 No.900 BFA00 70❶❷ 8 No.200 BFA06 70❶❷ 0 No.200 BFA080 70❶❷ 0 No DYF9 E❸❶ Yes NYF ❸❶ 220 Yes NYF ❸❶ 260 Yes NYF80 ❸❶ 0 Yes NYF20 ❸❶ 80 Yes NYF0 ❸❶ 0 Yes NYF00 ❸❶ 690 Yes Operational characteristics IEC standard motor powers 20V 00V 0V 00V [kw] [kw] [kw] [kw] ❶ Complete order code with the coil voltage digit or the coil voltage digit followed by 60 if 60Hz. Standard voltage are as follows: -- AC 0/60Hz 02 / 08 / 0 / 20 / 00V -- AC 60Hz / / / / (V). Example: BFA for BFA009 star-delta starter with 2VAC 0/60Hz power supply. BFA for BFA009 stardelta starter with 2VAC 60Hz power supply. ❷ The thermal overload relay is not included and must be purchased separately. Refer to the example given under Thermal relay adjustment range, for a correct choice and then to page - for the order code. ❸ The thermal overload relay is included. Replace with digit of thermal relay; see tables above, under Thermal relay adjustment range. ❹ To be mounted by the customer. ❺ Fuses for type co-ordination. For type 2 co-ordination, consult Customer Service; see contact details on inside front cover. ❻ TM ST with auxiliary supply VAC. TM ST A0 with auxiliary supply VAC. NOTE: For higher powers and voltages, or suitable for heavy-duty starting (centrifugal fans, mills, crushers) that is with starting time exceeding 2s, consult Customer Service; see contact details on inside front cover. Thermal relay adjustment range Choose the thermal relay adjustment range considering a value equal to 8% of rated motor current (Ie). Example: Ie=00A; 8% Ie=8A. The suitable relay range is 6-6A. During the setup, the relay is to be regulated at 8A. For DYF... type Digit defining Relay IEC am DYF thermal adj fuses starters relay range range A ❹❺ A For NYF... type Digit defining Relay IEC am NYF thermal adj fuses starters relay range range A ❹❺ A Components Starter Contactors Thermal Time relay Auxiliary contacts fitted Rigid overload on contactor: connections Line Delta Star relay Line Delta Star BFA BF09 0A BF09 0A BF09 0A ❷ (RF8) TM ST❻ BFX0 20 BFX0 BFX BFA02 70 BF2 0A BF2 0A BF09 0A ❷ (RF8) TM ST❻ BFX0 20 BFX0 BFX BFA08 70 BF8 0A BF8 0A BF2 0A ❷ (RF8) TM ST❻ BFX0 20 BFX0 BFX BFA02 70 BF2 0A BF2 0A BF8 0A ❷ (RF8) TM ST❻ BFX0 20 BFX0 BFX BFA BF26 00A BF26 00A BF8 0A ❷ (RF8) TM ST❻ BFX0 20 BFX0 BFX0 BFX2 2 BFA02 70 BF2 00A BF2 00A BF2 0A ❷ (RF8) TM ST❻ BFX0 20 BFX0 BFX0 BFX2 2 BFA08 70 BF8 00A BF8 00A BF2 0A ❷ (RF8) TM ST❻ BFX0 20 BFX0 BFX0 BFX2 2 BFA00 70 BF0 00A BF0 00A BF2 00A ❷ (RF82) TM ST❻ BFX0 20 BFX0 BFX0 BFA06 70 BF6 00A BF6 00A BF2 00A ❷ (RF82) TM ST❻ BFX0 20 BFX0 BFX0 BFA BF80 00A BF80 00A BF0 00A ❷ (RF82) TM ST❻ BFX0 20 BFX0 BFX0 DYF9 E BF9 00 BF9 00 BF0 00A RF9 TM ST❻ BFX0 20 BFX0 BFX0 NYF B 00 B 00 BF6 00 RF200 TM ST❻ G0 G BFX0 NYF B 00 B 00 BF80 00 RF200 TM ST❻ G0 G BFX0 NYF80 B80 00 B80 00 B 00 RF200 TM ST❻ G0 G G NYF20 B20 00 B20 00 B 00 RF20 TM ST❻ G0 G G NYF0 B0 00 B0 00 B80 00 RF20 TM ST❻ G0 G G NYF00 B00 00 B00 00 B20 00 RF20 TM ST❻ G0 G G Reference stardards Compliant with stardards: IEC/EN 6097-, IEC/EN page -8 pages -2 to 2

8 Star-delta starters. Non-metallic enclosure for starters Enclosed starters M P M PA70 ❶ Complete order code with the coil voltage digit or the coil voltage digit followed by 60 if 60Hz. Standard voltage are as follows: -- AC 0/60Hz 02 / 08 / 0 / 20 / 00V -- AC 60Hz / / / / (V). Example: MP for MP009 stardelta starter with 2VAC 0/60Hz power supply. MP for MP009 star-delta starter with 2VAC 60Hz power supply. ❷ The thermal overload relay is not included and must be purchased separately. Choose the thermal relay adjustment range considering a value equal to 8% of rated motor current (Ie). Example: Ie=0A; 8% Ie =.8A. The suitable relay range is -6.A, set at.8a, so the order code to select is RF8060). Refer to page - for the order codes available. ❸ Suitable for BFA...70 starters. ❹ TM ST with auxiliary supply VAC; TM ST A0 with auxiliary supply VAC. NOTE: For higher powers and voltage ratings or suitable for heavy-duty starting (centrifugal fans, mills, crushers) that is with starting time exceeding 2s, consult Customer Service; see contact details on inside front cover. Order Three-phase motor Qty Wt control. per Max IEC operating pkg current ( 0V) [A] n [kg] Star-delta starters in enclosure with Start and Stop/Reset buttons. Starting time up to 2s and a maximum of 0 operations/hour. M P009 70❶❷ 6.0 M P02 70❶❷ 22.0 M P08 70❶❷ 28.0 M P02 70❶❷.60 M P026 70❶❷.60 M P02 70❶❷ M P08 70❶❷ With switch disconnector, rotary door-coupling handle GAX6 and Start and Stop/Reset buttons. M P009 7❶❷ M P02 7❶❷ M P08 7❶❷ M P02 7❶❷.800 M P026 7❶❷.800 M P02 7❶❷ 0.00 M P08 7❶❷ Enclosure for star-delta starter, complete with Start and Stop/Reset buttons, metal plate fixed with piece of mm DIN (IEC/EN 607) rail. M PA70 ❸ 2.20 Operational characteristics IEC standard motor powers Maximum available space inside MP...70/7 with star-delta starters BFA V 00V 0V 00V [kw] [kw] [kw] [kw] Cable entry: Smooth surface; can be drilled by customer Ambient conditions: Operating temperature: C Storage temperature: C Degree of protection: IEC IP6 for MP ; UL Type, 2, /X for M UL versions. Special M... versions In addition to standard-indicated versions, culus certified starters are available up to 2A motor control rating max. This is also valid for the enclosure with general use rating of 6A. Add suffix UL to the order code, e.g. M PA70UL. Certifications and compliance Certifications obtained: UL Listed, for USA and Canada (File E9602), as Magnetic Motor Controllers - Enclosed (starters) and - Enclosures for M...PUL types. Compliant with standards: IEC/EN 6097-, IEC/EN , UL08, CSA C22.2 n for starters; UL 08A for MP A70UL Components Type Enclosure Contactors T/o Time Auxiliary contacts fitted Rigid Switch relay relay on contactor: connec- disconnector Line Delta Star ❷ Line Delta Star tions ❺ MP009 70/7 M PA70 BF09 0A BF09 0A BF09 0A (RF8) TM ST❹ BFX0 20 BFX0 BFX GA06 A MP02 70/7 M PA70 BF2 0A BF2 0A BF09 0A (RF8) TM ST❹ BFX0 20 BFX0 BFX GA02 A MP08 70/7 M PA70 BF8 0A BF8 0A BF2 0A (RF8) TM ST❹ BFX0 20 BFX0 BFX GA02 A MP02 70/7 M PA70 BF2 0A BF2 0A BF8 0A (RF8) TM ST❹ BFX0 20 BFX0 BFX GA00 A MP026 70/7 M PA70 BF26 00A BF26 00A BF8 0A (RF8) TM ST❹ BFX0 20 BFX0 BFX0 BFX2 2 GA06 SA MP02 70/7 M PA70 BF2 00A BF2 00A BF2 0A (RF8) TM ST❹ BFX0 20 BFX0 BFX0 BFX2 2 GA06 SA MP08 70/7 M PA70 BF8 00A BF8 00A BF2 0A (RF8) TM ST❹ BFX0 20 BFX0 BFX0 BFX2 2 GA06 SA ❺ For MP...7 types Combinations page - page -9 page -2-7

9 Empty non-metallic enclosures Accessories and spare parts Empty enclosures M...PA M...RA M...N Accessories and spare parts MX 20P MX 2P Order code Contactor type Thermal Degree Qty Wt ❶ relay of per ❷ protect. pkg Enclosures with Start-Stop/Reset pushbuttons. n [kg] M0PA BG06, BG09, RF9 IP BG2 MPA BF09A, BF2A, RF8 IP6 0. BF8A M2PA BF2A, BF26A RF8 IP6 0.7 BF2A M2PA❸ BF8A RF8 IP MPA❹ BF0A, BF0A, RF82 IP6.900 BF6A, BF80A, RF82 BF9, BF0 RF9 Enclosures with Reset pushbutton. M0RA BG06, BG09, RF9 IP6 0. BG2 MRA BF09A, BF2A, RF8 IP BF8A M2RA BF2A, BF26A RF8 IP BF2A M2RA❸ BF8A RF8 IP MRA❹ BF0A, BF0A, RF82 IP6.80 BF6A, BF80A, RF82 BF9, BF0 RF9 Enclosures without external pushbuttons. M0N BG06, BG09, RFA9 IP6 0.0 BG2 MN BF09A, BF2A, RF8 IP BF8A M2N❸ BF2A, BF26A RF8 IP BF2A M2N❸❺ BG.../ ❷ IP BF09A...BF2A M2N❸ BF8A RF8 IP MN BF0A, BF0A, RF82 IP6.800 BF6A, BF80A, RF82 BF9, BF0 RF9 ❶ To be purchased separately; refer to page 2- for contactor choice. ❷ To be purchased separately. Refer to pages -2 to 8 for thermal overload relay choice. For use of the overload relay in the M2N, consult Customer Service; see contact details on inside front cover. ❸ MX metal mounting plate included. ❹ MX 0 metal mounting plate included. ❺ To install eventual pushbuttons, selectors and/or other control accessories, use the series and mount the relay contact elements on the cover using the LPX AU20 mounting adapter. See section 7. Order code Description Qty Wt per pkg n [kg] MX 0 Threaded plug for unused holes, grey RAL70 MX 0P Stop/Reset button extension 0.00 rod for M0 enclosure MX P Stop/Reset button extension 0.00 rod for M enclosure MX 2P Stop/Reset button extension 0.00 rod for M2 enclosure MX 20P Mounting base for LPX C contact on M0 enclosure MX 2P Mounting base for LPX C contact on M, M2, M2 enclosure MX 0 Metal mounting plate for MN 0.00 MX Metal mounting plate for M2N 0.00 and M2 enclosures Enclosure Maximum operating current type ( 0V) A M M... 8 M M2N 8 M M... 0 General characteristics Enclosures are supplied with the following accessories: Accessory Type of enclosure M0 PA M PA M2 PA M2 PA M0 RA M RA M2 RA M2 RA Description Type Contact MX 20P holder MX 2P Buttons: LPC B76 - Start/Reset LPC B20 - Start LPC B Contact for LPX C0 Start button Stop/Reset MX 0P button MX P extension MX 2P Unused hole MX 0 threaded plug M PA enclosure: 2 Start and Stop/Reset pushbuttons, 2 G28 auxiliary terminals and MX0 mounting plate M RA enclosure: Reset pushbutton, 2 G28 auxiliary terminals and MX0 mounting plate MN enclosure: Supplied without accessories to be purchased separately including MX 0 mounting plate. Enclosures can house the following devices: M0 = BG with/without RF9 M = BF09A-BF2A-BF8A with/without RF8 M2 = BF2A-BF26A-BF2A, assemblies BFA 2 with/without RF8 M2N = BF2A-BF26A-BF2A, assemblies BGR/BGT/BGC and BFA 2 without overload M2 = BF26 BF8A, assemblies BGR/BGT/BGC and BFA 2 with/without overload M = BF0 BF0 and all assemblies with/without overload. Operational characteristics: Cable entry: M0/M//M2-2 knockouts PG./M20 on enclosure top and bottom M2N/M2-2 knockouts PG6/M2-PG29/M2 on enclosure top and bottom M - Smooth surfaces; can be drilled by customer Ambient conditions: Operating temperature: C Storage temperature: C Degree of protection: IEC IP6 for all; UL Type, 2, /X for M0/M/M2/M2N/M2 types and M UL versions. Special M versions In addition to standard-indicated versions, culus certified starters and enclosures are available up to 2A - motor control and 6A general use rating max (MX0 plate, earth/ground and neutral terminal plates are always included in this case). Add suffix UL to the order code of enclosures e.g. MN UL. Certifications and compliance Certifications obtained: EAC for all; for MNUL type, UL Listed for USA and Canada (culus File E0000) as Industrial control panels; for M0/M/M2PA/RA/N and other M UL types, UL Listed for USA and Canada (culus File E9602) under magnetic motor controllers as Polymeric enclosures - and CSA certified for Canada and USA (ccsaus File 97) as Non-metallic enclosures. UL/CSA pending for M2N and M2 types. Compliant with standards: IEC/EN 6097-, IEC/EN , UL 08, CSA CS22.2 n ; UL 08A and CSA -8 Combinations pages -0 to pages -6 and 7 page -20

10 Empty non-metallic enclosures M...PA EMPTY ENCLOSURES M0PA MPA M2PA M2PA MPA MPA M...RA EMPTY ENCLOSURES M0RA MRA M2RA M2RA MRA MRA M...N EMPTY ENCLOSURES M0N MN M2N M2N M2N MN Metal mounting plate MX (standard supplied) Metal mounting plate MX (standard supplied) Metal mounting plate MX 0 (to purchase separately) pages -6 and 7 page -20-9

11 Direct-on-line starters - Full voltage across the line. Non reversing three phase M...P... STARTERS, ENCLOSED M0 P M0 P M0 P M0 P M P M P M P M P M2 P M2 P M2 P M2 P M...R... STARTERS, ENCLOSED M0 R M0 R M0 R M0 R M R M R M R M R M2 R M2 R M2 R M2 R M2... STARTERS, ENCLOSED M2... STARTERS, ENCLOSED M2 P M2 P M2 R M2 R M2 P009 M... STARTERS, ENCLOSED M P to M P M P to M P M R to M R M R to M R pages -6 and 7 page -20

12 Direct-on-line starters - Full voltage across the line. Accessories and spare parts Maximum combinations for M0... and M... starters in enclosure For the fitting of add-on blocks and electronic relays in the starters, consult our Customer Service; see contact details on inside front cover. The enclosure cover can be equipped with various types of actuators and pilot lights, per following details: ) Upper position The cover must be drilled in this position, with a 22.mm hole, by the user and LPL..., LPM... and LPC ZS... pilot light can be fitted. To fit the LPL... (not type 8 LP2T IL P) pilot light head, the mounting base, type MX 20P for M0 enclosure or type MX 2P for M enclosure, must also be purchased. The LED element is snapped onto this mounting base. No adapter or base is needed for LPL..., LPM... and LPC ZS... 2) Middle position 2 Based on the enclosure type, in this position, the user finds either the Start button or threaded plug. Various actuators can be fitted in this position, such as flush or extended buttons, selectors or pilot lights, as illustrated below. To fit the actuators, the mounting base, type MX 20 for M0 enclosure, or type MX 2P for M enclosure, must also be purchased. The contact or LED elements are snapped onto this mounting base. No adapter or base is needed for LPL..., LPM... and LPC ZS... ) Lower position The STOP/RESET button is mounted in this position, except for the enclosure without buttons. This button activates the thermal overload relay via a mechanical actuator. In eventual applications without thermal overload relay, this button can be removed and the hole closed up by the threaded plug MX 0. 7.mm x Time relay TM... Protection relay PMV0 A0 Level control relay LVM2 20 Priority change relay LVMP 0 (one only relay on the left of the contactor) LPX C0... LPX C... LPX CS... LPX LP... LPX LE... LPX LPS... LPX C0... LPX C... LPX CS... MX 20P (M0) MX 2P (M) LPL... LPM... LPC ZS... MX 0 LPC BL... LPC QL... 2 LPC B... LPC Q... LPC S... MO... BG... M... BF09A BF2A BF8A LPC S... LPC SL... LPC B7... LPC BL7... LPC B7... RF9 RF8 pages -6 page -20 -

13 Direct-on-line starters - Full voltage across the line. Accessories and spare parts Maximum combinations for M2... starters in enclosure For the fitting of add-on blocks and electronic relays in the starters, consult our Customer Service; see contact details on inside front cover. The enclosure covers can be equipped with various types of actuators and pilot lights, per following details: ) Upper position The cover must be drilled in this position with a 22.mm hole by the user; LPL..., LPM... or LPC ZS... pilot light can be fitted. To fit the LPL... pilot light, the mounting base type MX 2P must also be purchased. The LED element is snapped onto this mounting base. No adapter or base is needed for LPL..., LPM... and LPC ZS... 2) Middle position 2 Based on the enclosure type, in this position, the user finds either the Start button or threaded plug. Various actuators can be fitted in this position, such as flush or extended buttons, selectors or pilot lights, as illustrated in the side figure. To fit the actuators (not required for 8 LP2T IL P pilot light), the mounting base type MX 2P must also be purchased. The contact or LED elements are snapped onto this mounting base. No adapter or base is needed for LPL..., LPM... and LPC ZS... ) Lower position The STOP/RESET button is mounted in this position, except for the enclosure without buttons. This button activates the thermal overload relay via a mechanical actuator. In eventual applications without thermal overload relay, this button can be removed and the hole closed up by the threaded plug MX 0. Various actuators can be fitted in this position, such as flush or extended buttons, selectors or pilot lights, as illustrated in the drawing below. To fit the actuators (not required for 8 LP2T IL P pilot light), the mounting base type MX 2P must also be purchased. The contact or LED elements are snapped onto this mounting base. No adapter or base is needed for LPL..., LPM... and LPC ZS... ) Upper position The cover must be drilled in this position with a 22.mm hole by the user whenever an external handle is needed for a switch disconnector fitted in the enclosure. Time relay TM... Protection relay PMV0 A0 Level control relay LVM2 20 Priority change relay LVMP 0 (two relays or one only on left and one on right side of the contactor) 7.mm mm 2 x or max x LPX C0... LPX C... LPX CS... PMV20/0/0/0//70... protection relay PMF20 A... protection relay PM0/0... protection relay LMV20... level control relay (one relay only on right side of the contactor) LPX LP... LPX LE... LPX LPS... LPX C0... LPX C... LPX CS... GAX6 GAX6 B GAX68 GAX68 B LPL... LPM LPC ZS... MX 2P MX 0 LPC BL... LPC QL... MX 2P 2 LPC B... LPC Q... M2... M2... M2... LPC S... BF2A BF26A BF2A n 2 BF09A n 2 BF2A n 2 BF8A n 2 BF2A BF09A BF2A BF8A BF2A BF26A BF2A LPC S... LPC SL... LPC B7... LPC BL7... ON I GAX7 090 OFF 0 BFX0 02 LPC B7... RF8 RF8 RF8 GA06 A GA02 A GA02 A LPC B pages -7 page -20

14 Maximum combinations for starters in M2N enclosure In addition to a direct-on-line, full voltage across the line, starter or reversing contactor assembly, various other electromechanical devices can be fitted. The cover of the M2N enclosure can be used across the entire surface to mount pushbuttons, measuring instruments, switch disconnectors GA06A GA00A and GA06SA type. No contact blocks or other additional accessories can be mounted on the contactor face of AC BF series; they can only be fitted on the contactor side since the cover is shallow. Eventually pushbuttons, selector switches and/or other control accessories of the series can be used and contact or LED elements can be mounted directly inside on the cover with the LPX AU20 mounting adapter; refer to section 7. The wall fixing holes and the cover closing captive screws are positioned outwards with respect to the sealing gasket. This guarantees the protection degree of the enclosure against infiltrations liquid (IEC IPX / UL Type X). The base has ribbing which facilitates the fixing of DIN rails, metal mounting plates and electronic printed boards. Grid references, marked by letters and numbers, are engraved on the interior surface of the cover. This grid allows to quickly identify the exact drilling points where pushbuttons, handles or pilot lights will be mounted. A safety sealing system keeps the cover and base together to avoid inopportune opening and tampering. Available space for fitting other electrical or electronic devices 0 82,6 6 M2N BG06 BG09 BG2 without overload M2N M2N M2N BF09A...BF2A without overload BGR... - BGT... - BGC... without overload n 2 BF09A n 2 BF2A n 2 BF8A n 2 BF2A All without overload BFA...2 without overload BF09A BF2A BF8A BF2A with GA06A...GA00A and GA06SA BFX0 02 ON I OFF 0 BFX0 0 pages -7 page -20 -

15 Maximum combinations for starters in M2 enclosure In addition to a direct-on-line, full voltage across the line, starter or reversing contactor assembly, various other electromechanical devices can be fitted. The cover of the M2 enclosure can be used across the entire surface to mount pushbuttons, measuring instruments, switch disconnectors GA06A GA00A and GA06SA type. Possible contact blocks or other additional accessories can be mounted on the contactor face of AC or DC BF series or on the contactor side since the cover is deep. Eventually pushbuttons, selector switches and/or other control accessories of the series can be used and contact or LED elements can be mounted directly inside on the cover with the LPX AU20 mounting adapter; refer to section 7. MX internal metal mounting plate is standard-supplied. The wall fixing holes and the cover closing captive screws are positioned outwards with respect to the sealing gasket. This guarantees the protection degree of the enclosure against liquid infiltrations (IEC IPX / UL Type X). The base has ribbing which facilitates the fixing of DIN rails, metal mounting plates and electronic printed boards. Grid references, marked by letters and numbers, are engraved on the interior surface of the cover. This grid allows to quickly identify the exact drilling points where pushbuttons, handles or pilot lights will be mounted. A safety sealing system keeps the cover and base together to avoid inopportune opening and tampering. Available space for fitting other electrical or electronic devices 0 6 7, 6 8 M M2... M2... M2... BF8 with or without overload BF26 - BF2 with or without overload BGR... - BGT... - BGC with or without overload RF9 n 2 BF26 - n 2 BF2 - n 2 BF8 with or without overload RF8 BFA...2 with or without overload RF8 BF09 BF2 BF8 BF26 BF2 BF8 with GA06A...GA00A and GA06SA BFX0 02 ON I OFF 0 RF8... RF8... RF8... BF09A...BF8A with BFX0 0 - pages -7 page -20

16 Direct-on-line starters Maximum combinations for starters in M enclosure In addition to a direct-on-line, full voltage across the line, starter or reversing contactor assembly, star-delta starters can be installed as illustrated at the lower right as well as various other electromechanical devices. The cover of the M enclosure can be used across the entire surface to mount pushbuttons, measuring instruments or switch disconnectors GA06A GA2A, etc. MX 0 internal metal mounting plate is standard supplied with MP and MR types; not included with the MN, it can be purchased separately. With the specifically designed hinges, the cover remains attached to the base, fully open, while the wiring work is being carried out. By applying slight pressure on the hinges, the cover can be released from the base. The cover closing captive screws and the wall fixing holes are positioned outwards with respect to the sealing gasket. This guarantees the protection degree of the enclosure against liquids infiltrations (IEC IPX / UL Type X). M... M P M P A safety sealing system keeps the cover and base together to avoid inopportune opening and tampering. Grid references, marked by letters and numbers, are engraved on the interior surface of the cover. This grid allows to quickly identify the exact drilling points where pushbuttons, handle or pilot lights will be mounted. A properly predrilled metal mounting plate (MX 0 standard supplied except for MN) permits to quickly and precisely fix equipment in place. The base has ribbing which facilitates the fixing of DIN rails, metal mounting plates and electronic printed boards. Available space for fitting other electrical or electronic devices M... M... M... n BF0 n BF0 n BF6 n BF80 n BF9 n BF0 n 2 BF0 n 2 BF0 n 2 BF6 n 2 BF80 n 2 BF9 n 2 BF0 n BF0 n BF0 n BF6 n BF9 n BF80 n BF0 + n GA... RF82 RF9 RF82 RF9 RF82 RF9 pages -7 page -20 -

17 [mm (in)] DIRECT-ON-LINE STARTERS - EMPTY ENCLOSURES M0 88 (.6 ) (.7 ) Ø. (0.8 ) 0. (. ). (.2 ) 9. (.70 ) M 88 (.6 ) (.7 ) Ø. (0.8 ). (6.2 ) 8. (.8 ). (.29 ) 8 (7.2 ) 7 (6.89 ) 202 (7.9 ) 9 (7.60 ) 9 (.9 ) 9. (0.76 ) 9 (.9 ) PG. / M20 knockouts on top and bottom 9. (0.76 ) PG. / M20 knockouts on top and bottom M2 M2 P009 0 (. ) (2.6 ) Ø. (0.8 ) 62. (6.9 ) 69. (6.70 ) 8. (.8 ) 0 (. ) (2.6 ) Ø. (0.8 ) 89. (7.6 ) 62. (6.9 ) 69. (6.70 ) 8. (.8 ) 2 (9.2 ) 22 (8.86 ) 60 (2.6 ) 22.8 (0.90 ) 2 (9.2 ) 22 (8.86 ) 60 (2.6 ) 22.8 (0.90 ) Ø0 (.8 ) PG. / M20 PG6/M2 knockouts on top and bottom PG. / M20 PG6/M2 knockouts on top and bottom -6

18 [mm (in)] M2N 7 (6.89 ) 98. (.88 ) M2 7 (6.89 ) 6 (6.0 ) 8, (6.2 ) 8, (.8 ) 20 (8.27 ) ) 28 (.0 ) 2 (2.0 ) Drilling for surface fixing. (6.0 ) Ø. (0.8 ) 28 (.0 ) 2 (2.0 ) Drilling for surface fixing. (6.0 ) Ø. (0.8 ) PG6 / M2 PG29 / M2 knockouts on top and bottom M (0. ) 220 (8.66 ) 87 (7.6 ) 77 (6.97 ) 70 (6.69 ) Drilling for surface fixing 78 (7.0 ) Ø 6.2 (0.2 ) 280 (.02 ) REVERSING CONTACTOR ASSEMBLIES BGR (.6 ).. (0.7 ) (0.7 ) Ø (0.6 ) 6 (0.2 ) BGT (.6 ).. (0.7 ) (0.7 ) Ø (0.6 ) ) 8. (0. ) 8. (0. ) BGTP (0.8 ) 88 (.6 ). (0.7 ). (0.7 ) 8 (2.28 ) (2.09 ) 0 (.97 ) Ø.❶ (0.0 ) 8 (2.28 ) 0 (.97 ) 8 (2.28 ) 0 (.97 ).9 (.7 ) 6 (2.20 ) 9.7 (0.8 ) 8. (0. ) 8. (0. ) BFA (0. ) 90 (. ).9 (.7 ) Ø.2 (0.6 ) 6 (2.20 ) 90 (. ) 8 (.27 ) 7 (2.79 ) 28 (9.7 ) 8, (.8 ) PG6 / M2 PG29 / M2 knockouts on top and bottom 8 (7.2 ) 8 (7.2 ) 9.7 (0.8 ) 8. (0. ) 8. (0. ) 8. (0. ) 6 (2.20 ).6 (0.22 ) ❶ Recommended PCB drillings.7-2mm ( ). (.8 ) -7

19 [mm (in)] CHANGEOVER CONTACTOR ASSEMBLIES BGC09 T (.6 ).. (0.7 ) (0.7 ) Ø (0.6 ).9 (.7 ) 6 (2.20 ) STAR-DELTA STARTERS OPEN FRAME BFA (0.9 ) 97. (7.77 ) 2. (6.00 ) 90 (. ) A B NYF... A C STARTER TYPE A B C NYF 0 (.8 ) 870 (.2 ) 9 (7.68 ) NYF 0 (.8 ) 870 (.2 ) 9 (7.68 ) NYF80 0 (.8 ) 870 (.2 ) 9 (7.68 ) NYF20 0 (7.2 ) 000 (9.7 ) 2 (9.2 ) NYF0 0 (7.2 ) 000 (9.7 ) 2 (9.2 ) NYF00 0 (7.2 ) 000 (9.7 ) 2 (9.2 ) B (0. ) STARTER TYPE A B BFA (. ) 09. (. ) BFA (. ) 09. (. ) BFA (. ) 09. (. ) BFA (. ) 09. (. ) BFA (. ) 9 (.68 ) BFA02 70 (. ) 9 (.68 ) BFA08 70 (. ) 9 (.68 ) BFA (6.8 ) 2 (.9 ) BFA (6.8 ) 2 (.9 ) BFA (7.20 ) 2 (.9 ) DYF (9.8 ) (0.9 ) (0.9 ) 6. (0.6 ) (. ) 9. (.9 ) (. ) 8 (6.22 ) 8 (2.28 ) 0 (.97 ) 9.7 (0.8 ) 8. (0. ) 8. (0. ) 8. (0. ) -8

20 [mm (in)] STAR-DELTA STARTERS IN ENCLOSURE - EMPTY ENCLOSURE FOR STAR-DELTA STARTERS MP M PA (.02 ) 87 (7.96 ) 77 (6.97 ) 70 (6.69 ) 220 (8.66 ) (0. ) Drilling for surface fixing Ø 6.2 (0.2 ) 28 (9.7 ) 20 (8.07 ) 6 (.7 ) 8 (7.28 ) 78 (7.0 ) 2 (9.6 ) MP (.02 ) 9 (7.60 ) 70 (6.69 ) (0. ) Drilling for surface fixing Ø 6.2 (0.2 ) 28 (9.7 ) 78 (7.0 ) 220 (8.66 ) 280 (.02 ) 70 (6.69 ) 92.9 (7.9 ) -9

21 DIRECT-ON-LINE STARTERS IN ENCLOSURE M...P Diagram - Incorporated button control for -phase motors LINE M...R Diagram 2 - External button control for -phase motors LINE M2 P Diagram - Incorporated button control and rotary actuator for -phase motors LINE Diagram - Power connection for -phase motors LINE 6 6 L L2 L A L L2 L () A L L2 L () L L2 L 2 6 T T2 T () 2 6 T T2 T I () 2 6 T T2 T O I R A T T2 T L L2 L 2 6 T T2 T T T2 T 2 6 T T2 T E 2 6 T T2 T O LOAD LOAD 2 LOAD I = Start; O = Stop/Reset R = Reset; I = Start; O = Stop I 2 6 T T2 T DIAGRAM 2: Connect the eventual two-wire control (e.g. automatism) between terminal of the contactor and terminal 96 of the thermal overload relay. IMPORTANT -- Remove jumpers and 6 and connect the auxiliary line to terminals A and for a control circuit with a voltage value different than the supply. -- Remove jumper and connect the neutral to terminal A for a control circuit between phase and neutral. -- SINGLE-PHASE SUPPLY The main circuit must be configured according to Diagram in the case of a single-phase line or motor. -- FUSES A set of three fuses must be connected upstream of the starter in the event no appropriate protection is included in the system. LOAD I = Start; O = Stop; E = Emergency Stop REVERSING CONTACTOR ASSEMBLY BGR... BGT... L L2 A L 2 A L L2 L 2 A L L2 L L L2 L A KM KM T T2 T 2 6 T T2 T T T2 T 2 6 T T2 T BFA...2 BGTP09... A L L2 L 2 A L L2 L 2 L L2 A 2 L L L2 L 2 A KM KM 2 6 T T2 T T T2 T T T2 T 2 6 T T2 T 22-20

22 CHANGEOVER CONTACTOR ASSEMBLY BGC09... L L2 A L L 7 L L2 L L 7 A KM T T2 T T STAR-DELTA STARTERS, OPEN FRAME AND ENCLOSED BFA MP T 6 8 T2 T T LINE...V -...Hz L L2 L KM KM FR 2 6 U2 V2 W2 M ~ U V W U2 V2 W2 M ~ U V W BFA BFA02 70 MP MP02 70 BF BFA08 70 MP MP S 22 S2 2 S 22 S KT (TM ST) 8 22 KM 96 2 FR KT A A (TM ST) KM KM KM 6 A A KM L KT (TM ST) 8 62 KM 96 6 FR KT A A (TM ST) KM KM KM 6 A A KM L -2

23 STAR-DELTA STARTERS, OPEN FRAME BFA00...BFA080 - DYF9 LINE...V -...Hz L L2 L KM KM FR 2 6 U2 V2 W2 M ~ U V W U2 V2 W2 M ~ U V W 2 S 22 S KT (TM ST) 8 62 KM KM KM 9 FR KT A (TM ST) 9 A KM A KM A L -22

24 STAR-DELTA STARTERS, OPEN FRAME NYF... KM 2 6 KM FR L L2 L LINE...V -...Hz U2 V2 W2 M ~ U V W U2 V2 W2 M ~ U V W S 22 S2 9 FR 96 7 KT (TM ST) 8 62 KM 6 KT A A (TM ST) KM KM 6 A KM KM A -2

25 Electromechanical starters and enclosures Direct-on-line starters Full voltage across the line. Non reversing CONFIGURATIONS FOR USA AND CANADA. Order code T/O MAX UL/CSA HP RATINGS INDICATED ON STARTER for magnetic motor starters RELAY (based on t/o relay adj range) in non-metallic enclosure ADJ with 2 push buttons RANGE Single phase Three phase [A] 20V 20V 200V 20V 80V 600V M0P009❶❷ ½ ½ M0P009❶❷V ¾ ¾ M0P009❶❷2V ½ M0P009❶❷ ¼ ¾ ½ ½ 2 M0P009❶❷ - - ½ M0P009❶❷ ¾ ½ 2 M0P009❶❷0 6-0 ½ ½ 2 M0P02❶❷❸ 9 - ½ ½ 7½ 0 MP009❶❷A ½ MP009❶❷A ½ ¾ MP009❶❷A ½ ½ ½ MP009❶❷A ¾ ¾ 2 MP009❶❷A8-6. ¼ ½ ½ MP009❶❷A ½ ½ 2 7½ MP009❶❷B0❸ 9 - ¾ 2 7½ MP02❶❷B0❸ 9-2 7½ 0 MP08❶❷B❸ M2P02❶❷B2 7-2 ½ 7½ M2P02❶❷B ½ 7½ M2P026❶❷B2 7-2 ½ 7½ 20 M2P026❶❷B ½ 7½ 20 M2P026❶❷B❸ ½ 7½ 20 M2P02❶❷B❸ 2-2 7½ M2P08❶❷B 2-8 7½ MP00❶❷B6UL❸❹ MP06❶❷B7UL❸❺ MP080❶❷B8❻ ❻ 0❻ 60❻ 7❻ MP09❶❷B9❻ ❻ 0❻ 60❻ 7❻ NOTE: The HP / FLA values vary from one motor to another; if possible, always verify the HP and FLA (or rated current) on the motor nameplate. Enclosure UL Type, 2, and X industrial control environment for M, M2, M2 and M UL versions; designation of control units can be: N without push buttons R with reset button only P per table, with start-stop push buttons S with start selector and stop push button. Consult Customer Service for any other combination required (e.g. with other type of contactors, contactor assemblies or definitepurpose version, different overload version or range, additional pilot lights, extra electrical or electronic elements); see contact details on inside front cover. Refer to ❶ below for specified standard configurations. ❶ Complete the order code by indicating: 0 if required without thermal overload relay 2 if required with three-phase overload relay if required with single-phase overload relay if required with automatic reset of overload relay for M0 types 7 if required with disconnect switch for M2 and M types 2 if required with reversing contactor combination for M2 and M types. ❷ Complete the order code by indicating coil voltage required: 0260 for 2V 60Hz 0860 for 8V 60Hz / 2V 0Hz 2060 for 20V 60Hz / 0V 0Hz for 220V 60Hz / 200V 0/60Hz 2060 for 20V 60Hz / 220V 0Hz 6060 for 60V 60Hz / 00V 0Hz 760 for 7V 60Hz. ❸ Maximum HP ratings per UL and CSA can be different when definite-purpose contactors are considered. Consult with Customer Service for further information; see contact details on inside front cover. ❹ Short circuit protective device This enclosed starter is suitable for use on a circuit capable of delivering not more than,000rms symmetrical amperes, 600V max, when protected with Class RK type, Fuse size 200A. ❺ Maximum UL ratings is 2A for motor control and 6A for general use. Short circuit protective device This enclosed starter is suitable for use on a circuit capable of delivering not more than 0,000rms symmetrical amperes, 600V max, when protected with Class RK type, Fuse size 22A. ❻ No CSA or UL certification. Indicated values correspond to UL/CSA magnetic contactor ratings and for indication and reference purposes only. Certifications obtained: CSA certified for Canada and USA (ccsaus - File 97) as Magnetic Motor Controllers at max 600VAC, max HP per single phase, max 60HP three phase, max 2A with general purpose enclosure. UL Listed for USA and Canada (culus - File E9602) as Magnetic Motor Controllers Enclosed. Markings: Line (voltage and frequency value) Amps (overload adjustment range) Max HP (horsepower value) Control (coil and frequency value) Caution: Bonding between conduits must be provided. -2

26 Typical full-load current values of single and three phase electric motors THREE-PHASE POWER RATINGS Rated motor current 200V 20V V 80-V 00V 0-80V 00V 0-600V 690V [HP] [kw] [A] [A] [A] [A] {A] [A] [A] [A] [A] / / / / SINGLE-PHASE POWER RATINGS Rated motor current [HP] [A] at 20V [A] at 20V /0. /8.8.9 / / / / / / / The information in the chart has been obtained from the IEC/EN standards. The kw ratings are preferred rated values according to IEC (primary series) at 0/60Hz while Horsepower and corresponding current values are according to UL 08 Industrial Control Standard at 60Hz. The full load current values listed are for motors running at standard speeds with normal torque characteristics. Motors which are non-standard, such as low speed, high torque or other special applications may have higher full load currents. Caution: For accurate and reliable motor protection, motor nameplate current should be used to obtain actual motor full load amps for all motors. The information given is for indication and reference purposes only. -2