TITLE MICROCIRCUIT, LINEAR, LC 2 MOS, QUAD SPST SWITCHES, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV

Size: px

Start display at page:

Download "TITLE MICROCIRCUIT, LINEAR, LC 2 MOS, QUAD SPST SWITCHES, MONOLITHIC SILICON REVISIONS LTR DESCRIPTION DATE APPROVED REV PAGE REV PAGE REV"

Nelson Snow
6 years ago
Views:

1 REIION LTR ECRIPTION TE PPROE Prepared in accordance with ME Y14.24 endor item drawing RE PGE RE PGE RE TTU OF PGE RE PGE PMIC N/ PREPRE BY Phu H. Nguyen L LN N MRITIME Original date of drawing YY MM CHECKE BY Phu H. Nguyen PPROE BY Thomas M. Hess TITLE MICROCIRCUIT, LER, LC 2 MO, QU PT WITCHE, MONOLITHIC ILICON COE IENT. NO. 62/12638 RE PGE 1 OF 13 MC N/

2 1. COPE 1.1 cope. This drawing documents the general requirements of a high performance LC 2 MO, quad PT switches microcircuit, with an operating temperature range of -55 C to +125 C. 1.2 endor Item rawing dministrative Control Number. The manufacturer s P is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: evice type(s). 62/ X E rawing evice type Case outline Lead finish number (ee 1.2.1) (ee 1.2.2) (ee 1.2.3) evice type Generic Circuit function 01 G201-EP LC 2 MO quad PT switches Case outline(s). The case outlines are as specified herein. Outline letter Number of pins JEEC PUB 95 Package style X 16 JEEC M-012-C tandard mall Outline Package Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator B C E Z Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other L LN N MRITIME 62/12638 RE PGE 2

3 1.3 bsolute maximum ratings. 1/ to to GN to GN nalog inputs to / igital inputs... 2 to + 2 or 20 m (whichever occurs first) 2/ Pulsed current, or m (pulsed at 1 ms, 10% duty cycle maximum) Continuous current, or m Operating temperature rang C to +125 C torage temperature range C to 150 C Power dissipation: Up to +75 C mw erates above +75 C by... 6 mw/ C Lead soldering: Reflow, Peak temperature... 26(+0/-5) C Time at Peak temperature sec to 40 sec 2. PPLICBLE OCUMENT JEEC OLI TTE TECHNOLOGY OCITION (JEEC) JEP95 Registered and tandard Outlines for emiconductor evices (Copies of these documents are available online at or from JEEC olid tate Technology ssociation, 3103 North 10th treet, uite 240, rlington, ) 3. REQUIREMENT 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer s part number as shown in 6.3 herein and as follows:. Manufacturer s name, CGE code, or logo B. Pin 1 identifier C. E identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer s part number and with items and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3 and table I herein. 3.4 esign, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 1/ tresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. 2/ Over voltages at,, or are clamped by internal diodes. Current should be limited to the maximum ratings given. L LN N MRITIME 62/12638 RE PGE 3

4 3. REQUIREMENT 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer s part number as shown in 6.3 herein and as follows:. Manufacturer s name, CGE code, or logo B. Pin 1 identifier C. E identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer s part number and with items and C (if applicable) above. 3.5 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.6 esign, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 iagrams Case outline. The case outline shall be as shown in and figure Terminal connections. The terminal connections shall be as shown in figure Terminal function. The terminal function shall be as shown in figure Truth table. The truth table shall be as shown in figure Functional block diagram. The functional block diagram shall be as shown in figure On resistance. The on resistance shall be as shown in figure Off leakage. The off leakage shall be as shown in figure On leakage. The on leakage shall be as shown in figure witching time. The switching time shall be as shown in figure Charge injection. The charge injection shall be as shown in figure Off isolation. The off isolation shall be as shown in figure Channel to channel crosstalk. The channel to channel crosstalk 12. L LN N MRITIME 62/12638 RE PGE 4

5 TBLE I. Electrical performance characteristics. 1/ Test ymbol Test conditions 2/ Limits 25 C -55 C to +125 Min Max Min Max UL UPPLY nalog switch nalog signal range ±15 ±15 On Resistance (RON) R ON , I = 1 m; see FIGURE 6 60 TYP Ω R ON vs ( ) 20 TYP % R ON rift 0.5 TYP %/ C R ON Match = 0, I = 1 m 5 TYP % Leakage currents ource off leakage I (Off) = ±14, = 14, ee FIGURE 7 ±0.5 TYP n ±2.0 ±100 rain off leakage I (Off) = ±14, = 14, ee FIGURE 7 ±0.5 TYP ±2.0 ±100 Channel on leakage I, I (On) = ±14, ee FIGURE 8 ±0.5 TYP ±2.0 ±200 igital inputs Input high voltage H 2.4 Input low voltage L 0.8 Input current I L, I H 1 µ ynamic characteristics t OPEN ee FIGURE 9 30 TYP ns t ON 3/ ee FIGURE t OFF 3/ ee FIGURE Off isolation = 10 p-p, f = 100 khz, R L = 75 Ω, 80 TYP db ee FIGURE 11 Channel to channel crosstalk ee FIGURE TYP db C (Off) 5 TYP pf C (Off) 5 TYP C, C (On) 16 TYP C igital input capacitance 5 TYP Q J Charge injection R = 0 Ω, C L = 1000 pf, = 0 ee FIGURE TYP pc Unit ee footnote at end of table. L LN N MRITIME 62/12638 RE PGE 5

6 TBLE I. Electrical performance characteristics - Continued. 1/ Test ymbol Test conditions 2/ Limits 25 C -55 C to +125 Min Max Min Max UL UPPLY Continued. Power supply I igital inputs = L or H 0.6 TYP 2 m I 0.1 TYP 0.2 Power dissipation 33 mw 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ = 15 ±10%, = - 15 ±10%, GN = 0. ll specifications -55 C to +125, unless otherwise noted. 3/ ample tested at 25 C to ensure compliance. Unit L LN N MRITIME 62/12638 RE PGE 6

7 Case X e b E E1 L ETIL EE ETIL 1 ETG PLNE c imensions ymbol Millimeters Inches ymbol Millimeters Inches Min Max Min Max Min Max Min Max E E b e 1.27 BC.050 BC c L NOTE: 1. Controlling dimensions are in millimeters; inch dimensions are rounded-off millimeter equivalents for reference only and are not appropriate for use in design. 2. Falls within JEEC M-012-C. FIGURE 1. Case outline. L LN N MRITIME 62/12638 RE PGE 7

8 Case outline X Terminal Terminal symbol number Terminal number Terminal symbol GN 12 NC NC = No Connect FIGURE 2. Terminal connections. Case outline X Terminal escription Number Mnemonic 1 1 Logic control input. 2 1 rain terminal. Can be an input or output. 3 1 ource terminal. Can be an input or output. 4 Most negative power supply. This pin is used in dual supply applications only and should be tied to ground in single supply applications. 5 GN Ground (0 ) reference. 6 4 ource terminal. Can be an input or output. 7 4 rain terminal. Can be an input or output. 8 4 Logic control input. 9 3 Logic control input rain terminal. Can be an input or output ource terminal. Can be an input or output. 12 NC No connect. Not internally connected. 13 Most positive power supply ource terminal. Can be an input or output rain terminal. Can be an input or output Logic control input. FIGURE 3. Terminal function. L LN N MRITIME 62/12638 RE PGE 8

9 Input x witch condition 0 On 1 Off FIGURE 4. Truth table FIGURE 5. Functional block diagram. I 1 R ON =1/I FIGURE 6. On resistance. L LN N MRITIME 62/12638 RE PGE 9

10 I (OFF) I (OFF) FIGURE 7. Off leakage. I (ON) NC FIGURE 8. On leakage O 50% pf 90% O GN t ON t OFF -15 FIGURE 9. witching time. L LN N MRITIME 62/12638 RE PGE 10

11 +15 5 R + C1 1 F - O O O GN Q J =C L x O -15 FIGURE 10. Charge injection. +15 O R L 75 GN = 5-15 OFF IOLTION= 20 x LOG( / O ) FIGURE 11. Off isolation. L LN N MRITIME 62/12638 RE PGE 11

12 O NC R L 75 GN CHNNEL-TO-CHNNEL CROTLK= = x LOG( / O ) FIGURE 12. Channel to channel crosstalk. L LN N MRITIME 62/12638 RE PGE 12

13 4. ERIFICTION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. uch procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPRTION FOR ELIERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTE 6.1 E. evices are electrostatic discharge sensitive and are classified as E class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 uggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. L Land and Maritime maintains an online database of all current sources of supply at endor item drawing administrative control number 1/ evice manufacturer CGE code endor part number 62/ XE G201RZ-EP-RL7 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CGE code ource of supply nalog evices 1 Technology Way P.O. Box 9106 Norwood, M L LN N MRITIME 62/12638 RE PGE 13

DLA LAND AND MARITIME COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, CMOS, ±% V/ +5V, 4 Ω, SINGLE SPDT SWITCH, MONOLITHIC SILICON REVISIONS

DLA LAND AND MARITIME COLUMBUS, OHIO TITLE MICROCIRCUIT, DIGITAL, CMOS, ±% V/ +5V, 4 Ω, SINGLE SPDT SWITCH, MONOLITHIC SILICON REVISIONS REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/ PREPRED BY Phu H. Nguyen DL