DLA LAND AND MARITIME COLUMBUS, OHIO

Transcription

1 REVISIONS LTR DESCRIPTION DTE PPROVED Prepared in accordance with SME Y14.24 Vendor item drawing REV PGE REV PGE REV STTUS OF PGES REV PGE PMIC N/ PREPRED BY RICK OFFICER DL LND ND MRITIME Original date of drawing YY-MM-DD CHECKED BY RJESH PITHDI PPROVED BY CHRLES F. SFFLE TITLE MICROCIRCUIT, LINER, QUD CHNNEL DIGITL ISOLTOR, MONOLITHIC SILICON CODE IDENT. NO. REV PGE 1 OF 25 MSC N/ 5962-V094-15

2 1. SCOPE 1.1 Scope. This drawing documents the general requirements of a high performance quad channel, digital isolator microcircuit, with an operating temperature range of -55 C to +125 C. 1.2 Vendor Item Drawing dministrative Control Number. The manufacturer s PIN is the item of identification. The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation: Device type(s) X E Drawing Device type Case outline Lead finish number (See 1.2.1) (See 1.2.2) (See 1.2.3) Device type Generic Circuit function 01 DUM3402 Quad channel, digital isolator Case outline(s). The case outline(s) are as specified herein. Outline letter Number of pins JEDEC PUB 95 Package style X 16 MS-013- Small outline surface mount Lead finishes. The lead finishes are as specified below or other lead finishes as provided by the device manufacturer: Finish designator B C D E Z Material Hot solder dip Tin-lead plate Gold plate Palladium Gold flash palladium Other DL LND ND MRITIME REV PGE 2

3 1.3 bsolute maximum ratings. 1/ Supply voltages (V DD1, V DD2 ) V to +7.0 V 2/ Input voltages (V I, V IB, V IC, V ID, V E1, V E2 ) V to V DDI V 2/ 3/ Output voltage (V O, V OB, V OC, V OD ) V to V DDO V 2/ 3/ verage output current per pin: 4/ Side 1 (I O1 ) m to +18 m Side 2 (I O2 ) m to +22 m Common mode transients (CM H, CM L ) kv/ s to +100 kv/ s 5/ Storage temperature range (T STG ) C to +150 C 1.4 Recommended operating conditions. 6/ Supply voltages (V DD1, V DD2 ) V to 5.5 V 2/ Input signal rise and fall times ms Operating temperature range (T ) C to +125 C 1.5 Package characteristics. Resistance (input to output) (R IO ) typical 7/ Capacitance (input to output) (C IO ) with f = 1 MHz pf typical 7/ Input capacitance (C I ) pf typical 8/ Integrated circuit junction to case thermal resistance: Thermocouple located at center of package underside. Side 1 ( JCI ) C/W typical Side 2 ( JCO ) C/W typical 1/ Stresses beyond those listed under absolute maximum rating may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. 2/ ll voltages are relative to their respective ground. 3/ V DDI and V DDO refer to the supply voltages on the input and output sides of a given channel, respectively. 4/ See figure 5 for maximum rated current values for various temperatures. 5/ Refers to common mode transients across the insulation barrier. Common mode transients exceeding the absolute maximum ratings can cause latch up or permanent damage. 6/ Use of this product beyond the manufacturers design rules or stated parameters is done at the user s risk. The manufacturer and/or distributor maintain no responsibility or liability for product used beyond the stated limits. 7/ Device considered a 2 terminal device; V DD1 pin to GND1 pin are shorted together, and GND2 pin to V DD2 pin are shorted together. 8/ Input capacitance is from any input data pin to ground. DL LND ND MRITIME REV PGE 3

4 2. PPLICBLE DOCUMENTS JEDEC Solid State Technology ssociation JEDEC PUB 95 Registered and Standard Outlines for Semiconductor Devices (Copies of these documents are available online at or from JEDEC Solid State Technology ssociation, 3103 North 10th Street, Suite 240 S, rlington, V ). 3. REQUIREMENTS 3.1 Marking. Parts shall be permanently and legibly marked with the manufacturer s part number as shown in 6.3 herein and as follows:. Manufacturer s name, CGE code, or logo B. Pin 1 identifier C. ESDS identification (optional) 3.2 Unit container. The unit container shall be marked with the manufacturer s part number and with items and C (if applicable) above. 3.3 Electrical characteristics. The maximum and recommended operating conditions and electrical performance characteristics are as specified in 1.3, 1.4, and table I herein. 3.4 Design, construction, and physical dimension. The design, construction, and physical dimensions are as specified herein. 3.5 Diagrams Case outline. The case outline shall be as shown in and figure Terminal connections. The terminal connections shall be as shown in figure Truth table. The truth table shall be as shown in figure Logic diagram. The logic diagram shall be as shown in figure Thermal derating curve. The thermal derating curve shall be as shown in figure Data rate graphs. The data rate graphs shall be as shown in figures 6 through 9. DL LND ND MRITIME REV PGE 4

5 TBLE I. Electrical performance characteristics. 1/ Test Symbol Conditions 5 V operation 2/ Temperature, T Device type Min Limits Max Unit DC specifications Input supply current per channel, quiescent Output supply current per channel, quiescent I DDI (Q) -55 C to +125 C m 0.57 typical I DDO (Q) -55 C to +125 C m 0.29 typical Total supply current 3/ DC to 2 Mbps V DD1 or V DD2 supply current I DD1(Q), DC to 1 MHz logical signal -55 C to +125 C m frequency I DD2(Q) 2.0 typical Total supply current 3/ 10 Mbps V DD1 or V DD2 supply current I DD1(10), 5 MHz logical signal frequency -55 C to +125 C m I DD2(10) 6.0 typical DC specifications Input leakage per channel V EX input pull up current Tristate leakage current per channel Logic high input threshold Logic low input threshold I I 0 V V IX V DDX -55 C to +125 C typical I PU V EX = 0 V -55 C to +125 C typical I OZ -55 C to +125 C typical V IH, V EH -55 C to +125 C V V IL, V EL -55 C to +125 C V See footnotes at end of table. DL LND ND MRITIME REV PGE 5

6 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 5 V operation 2/ Temperature, T Device type Min Limits Max Unit DC specifications continued. Logic high output voltages V OH, V OBH I OX = -20, V IX = V IXH 4/ 5/ -55 C to +125 C 01 (V DD1 or V DD2 ) 0.1 V 5.0 typical V OCH, V ODH I OX = -4 m, V IX = V IXH 4/ 5/ -55 C to +125 C (V DD1 or V DD2 ) typical Logic low output voltage V OL, I OX = 20, V IX = V IXL 4/ 6/ -55 C to +125 C V V OBL 0.0 typical V OCL, I OX = 400, V IX = V IXL 4/ 6/ -55 C to +125 C 0.1 V ODL 0.04 typical I OX = 4 m, V IX = V IXL 4/ 6/ -55 C to +125 C typical Switching specifications. Minimum pulse width PW C L = 15 pf, CMOS signal levels -55 C to +125 C ns Maximum data rate C L = 15 pf, CMOS signal levels -55 C to +125 C Mbps Propagation delay t PHL, C L = 15 pf, CMOS signal levels -55 C to +125 C ns t PLH 32 typical Pulse width distortion t PLH t PHL Pulse width distortion t PLH t PHL change versus temperature Propagation delay skew PWD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 3 ns C L = 15 pf, CMOS signal levels 01 5 typical ps/ C t PSK C L = 15 pf, CMOS signal levels -55 C to +125 C ns See footnotes at end of table. DL LND ND MRITIME REV PGE 6

7 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 5 V operation 2/ Temperature, T Device type Min Limits Max Unit Switching specifications continued. Channel to channel matching, codirectional channels Channel to channel matching, opposing directional channels t PSKCD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 3 ns t PSKOD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 6 ns Output propagation delay, disable (high/low to high impedance) Output propagation delay, enable (high impedance to high/low) t PHZ, t PLZ t PZH, t PZL C L = 15 pf, CMOS signal levels -55 C to +125 C 01 8 ns 6 typical C L = 15 pf, CMOS signal levels -55 C to +125 C 01 8 ns 6 typical Output rise/fall time (10% to 90%) Common mode 7/ transient immunity logic high output Common mode 7/ transient immunity logic low output t R / t F C L = 15 pf, CMOS signal levels typical ns CM H V IX = V DD1 /V DD2, V CM = 1000 V, -55 C to +125 C kv/ s transient magnitude = 800 V 35 typical CM L V IX = 0 V, V CM = 1000 V, -55 C to +125 C kv/ s transient magnitude = 800 V 35 typical Refresh rate fr typical Mbps Dynamic supply current per channel, input Dynamic supply current per channel, output I DDI(D) 8/ typical m/ Mbps I DDO(D) 8/ typical m/ Mbps See footnotes at end of table. DL LND ND MRITIME REV PGE 7

8 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 3.3 V operation 9/ Temperature, T Device type Min Limits Max Unit DC specifications Input supply current per channel, quiescent Output supply current per channel, quiescent I DDI (Q) -55 C to +125 C m 0.31 typical I DDO (Q) -55 C to +125 C m 0.19 typical Total supply current 3/ DC to 2 Mbps V DD1 or V DD2 supply current I DD1(Q), DC to 1 MHz logical signal -55 C to +125 C m I DD2(Q) frequency 1.2 typical Total supply current 3/ 10 Mbps V DD1 or V DD2 supply current I DD1(10), 5 MHz logical signal frequency -55 C to +125 C m I DD2(10) 3.4 typical DC specifications Input leakage per channel V EX input pull up current Tristate leakage current per channel Logic high input threshold Logic low input threshold I I 0 V V IX V DDX -55 C to +125 C typical I PU V EX = 0 V -55 C to +125 C typical I OZ -55 C to +125 C typical V IH, V EH -55 C to +125 C V V IL, V EL -55 C to +125 C V See footnotes at end of table. DL LND ND MRITIME REV PGE 8

9 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 3.3 V operation 9/ Temperature, T Device type Min Limits Max Unit DC specifications continued. Logic high output voltages V OH, V OBH I OX = -20, V IX = V IXH 4/ 5/ -55 C to +125 C 01 (V DD1 or V DD2 ) 0.1 V 3.3 typical V OCH, V ODH I OX = -4 m, V IX = V IXH 4/ 5/ -55 C to +125 C (V DD1 or V DD2 ) typical Logic low output voltage V OL, I OX = 20, V IX = V IXL 4/ 6/ -55 C to +125 C V V OBL 0.0 typical V OCL, I OX = 400, V IX = V IXL 4/ 6/ -55 C to +125 C 0.1 V ODL 0.04 typical I OX = 4 m, V IX = V IXL 4/ 6/ -55 C to +125 C typical Switching specifications Minimum pulse width PW C L = 15 pf, CMOS signal levels -55 C to +125 C ns Maximum data rate C L = 15 pf, CMOS signal levels -55 C to +125 C Mbps Propagation delay t PHL, C L = 15 pf, CMOS signal levels -55 C to +125 C ns t PLH 38 typical Pulse width distortion t PLH t PHL Pulse width distortion t PLH t PHL change versus temperature Propagation delay skew PWD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 3 ns C L = 15 pf, CMOS signal levels 01 5 typical ps/ C t PSK C L = 15 pf, CMOS signal levels -55 C to +125 C ns See footnotes at end of table. DL LND ND MRITIME REV PGE 9

10 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 3.3 V operation 9/ Temperature, T Device type Min Limits Max Unit Switching specifications continued. Channel to channel matching, codirectional channels Channel to channel matching, opposing directional channels t PSKCD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 3 ns t PSKOD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 6 ns Output propagation delay, disable (high/low to high impedance) Output propagation delay, enable (high impedance to high/low) t PHZ, t PLZ t PZH, t PZL C L = 15 pf, CMOS signal levels -55 C to +125 C 01 8 ns 6 typical C L = 15 pf, CMOS signal levels -55 C to +125 C 01 8 ns 6 typical Output rise/fall time (10% to 90%) Common mode 7/ transient immunity logic high output Common mode 7/ transient immunity logic low output t R / t F C L = 15 pf, CMOS signal levels 01 3 typical ns CM H V IX = V DD1 /V DD2, V CM = 1000 V, -55 C to +125 C kv/ s transient magnitude = 800 V 35 typical CM L V IX = 0 V, V CM = 1000 V, -55 C to +125 C kv/ s transient magnitude = 800 V 35 typical Refresh rate fr typical Mbps Dynamic supply current per channel, input Dynamic supply current per channel, output I DDI(D) 8/ typical m/ Mbps I DDO(D) 8/ typical m/ Mbps See footnotes at end of table. DL LND ND MRITIME REV PGE 10

11 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 5 V / 3.3 V or 3.3 V / 5 V operation 10/ Temperature, T Device type Min Limits Max Unit DC specifications Input supply current per channel, quiescent I DDI (Q) 5 V / 3.3 V operation -55 C to +125 C m 0.57 typical 3.3 V / 5 V operation -55 C to +125 C typical Output supply current per channel, quiescent I DDO (Q) 5 V / 3.3 V operation -55 C to +125 C m 0.29 typical 3.3 V / 5 V operation -55 C to +125 C typical Total supply current 3/ DC to 2 Mbps V DD1 supply current I DD1(Q) DC to 1 MHz logical signal frequency, 5 V / 3.3 V operation DC to 1 MHz logical signal frequency, 3.3 V / 5 V operation V DD2 supply current I DD2(Q) DC to 1 MHz logical signal frequency, 5 V / 3.3 V operation DC to 1 MHz logical signal frequency, 3.3 V / 5 V operation -55 C to +125 C m 2.0 typical -55 C to +125 C typical -55 C to +125 C m 1.2 typical -55 C to +125 C typical Total supply current 3/ 10 Mbps V DD1 supply current I DD1(10) 5 MHz logical signal frequency, 5 V / 3.3 V operation 5 MHz logical signal frequency, 3.3 V / 5 V operation -55 C to +125 C m 6.0 typical -55 C to +125 C typical See footnotes at end of table. DL LND ND MRITIME REV PGE 11

12 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 5 V / 3.3 V or 3.3 V / 5 V operation 10/ Temperature, T Device type Min Limits Max Unit DC specifications continued. Total supply current 3/ 10 Mbps V DD2 supply current I DD2(10) 5 MHz logical signal frequency, 5 V / 3.3 V operation 5 MHz logical signal frequency, 3.3 V / 5 V operation -55 C to +125 C m 3.3 typical -55 C to +125 C typical Input leakage per channel V EX input pull up current Tristate leakage current per channel I I 0 V V IX V DDX -55 C to +125 C typical I PU V EX = 0 V -55 C to +125 C typical I OZ -55 C to +125 C typical Logic high input threshold V IH, V EH 5 V / 3.3 V operation -55 C to +125 C V 3.3 V / 5 V operation 1.6 Logic low input threshold V IL, V EL 5 V / 3.3 V operation -55 C to +125 C V 3.3 V / 5 V operation 0.4 Logic high output voltages V OH, V OBH I OX = -20, V IX = V IXH 4/ 5/ -55 C to +125 C 01 (V DD1 or V DD2 ) 0.1 V (V DD1 or V DD2 ) typical V OCH, V ODH I OX = -4 m, V IX = V IXH 4/ 5/ -55 C to +125 C (V DD1 or V DD2 ) 0.4 (V DD1 or V DD2 ) 0.2 typical See footnotes at end of table. DL LND ND MRITIME REV PGE 12

13 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 5 V / 3.3 V or 3.3 V / 5 V operation 10/ Temperature, T Device type Min Limits Max Unit DC specifications continued. Logic low output voltage V OL, I OX = 20, V IX = V IXL 4/ 6/ -55 C to +125 C V V OBL 0.0 typical V OCL, I OX = 400, V IX = V IXL 4/ 6/ -55 C to +125 C 0.1 V ODL 0.04 typical I OX = 4 m, V IX = V IXL 4/ 6/ -55 C to +125 C typical Switching specifications Minimum pulse width PW C L = 15 pf, CMOS signal levels -55 C to +125 C ns Maximum data rate C L = 15 pf, CMOS signal levels -55 C to +125 C Mbps Propagation delay t PHL, C L = 15 pf, CMOS signal levels -55 C to +125 C ns t PLH 35 typical Pulse width distortion t PLH t PHL Pulse width distortion t PLH t PHL change versus temperature Propagation delay skew PWD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 3 ns C L = 15 pf, CMOS signal levels 01 5 typical ps/ C t PSK C L = 15 pf, CMOS signal levels -55 C to +125 C ns See footnotes at end of table. DL LND ND MRITIME REV PGE 13

14 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 5 V / 3.3 V or 3.3 V / 5 V operation 10/ Temperature, T Device type Min Limits Max Unit Switching specifications continued. Channel to channel matching, codirectional channels Channel to channel matching, opposing directional channels t PSKCD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 3 ns t PSKOD C L = 15 pf, CMOS signal levels -55 C to +125 C 01 6 ns Output propagation delay, disable (high/low to high impedance) Output propagation delay, enable (high impedance to high/low) t PHZ, t PLZ t PZH, t PZL C L = 15 pf, CMOS signal levels -55 C to +125 C 01 8 ns 6 typical C L = 15 pf, CMOS signal levels -55 C to +125 C 01 8 ns 6 typical Output rise/fall time (10% to 90%) t R / t F C L = 15 pf, CMOS signal levels, 5 V / 3.3 V operation 01 3 typical ns C L = 15 pf, CMOS signal levels, 3.3 V / 5 V operation 2.5 typical Common mode 7/ transient immunity logic high output Common mode 7/ transient immunity logic low output CM H V IX = V DD1 /V DD2, V CM = 1000 V, transient magnitude = 800 V CM L V IX = 0 V, V CM = 1000 V, transient magnitude = 800 V -55 C to +125 C kv/ s 35 typical -55 C to +125 C kv/ s 35 typical Refresh rate fr 5 V / 3.3 V operation typical Mbps 3.3 V / 5 V operation 1.1 typical See footnotes at end of table. DL LND ND MRITIME REV PGE 14

15 TBLE I. Electrical performance characteristics Continued. 1/ Test Symbol Conditions 5 V / 3.3 V or 3.3 V / 5 V operation 10/ Temperature, T Device type Min Limits Max Unit Dynamic supply current per channel, input Dynamic supply current per channel, output I DDI(D) 5 V / 3.3 V operation 8/ typical m/ Mbps 3.3 V / 5 V operation 8/ 0.10 typical I DDO(D) 5 V / 3.3 V operation 8/ typical m/ Mbps 3.3 V / 5 V operation 8/ 0.05 typical See footnotes at end of table. DL LND ND MRITIME REV PGE 15

16 TBLE I. Electrical performance characteristics Continued. 1/ 1/ Testing and other quality control techniques are used to the extent deemed necessary to assure product performance over the specified temperature range. Product may not necessarily be tested across the full temperature range and all parameters may not necessarily be tested. In the absence of specific parametric testing, product performance is assured by characterization and/or design. 2/ ll voltages are relative to their respective ground. 4.5 V V DD1 5.5 V and 4.5 V V DD2 5.5 V. Unless otherwise specified, all minimum / maximum specifications apply over the entire recommended operation range. ll typical specifications are at T = 25 C, V DD1 = V DD2 = 5 V. 3/ The supply current values for all four channels are combined when running at identical data rates. Output supply current values are specified with no output load present. See figures 6 through 8 for information on per channel supply current as a function of data rate for unloaded and loaded conditions. See figures 9 and 10 for total V DD1 and V DD2 supply currents as a function of data rate for device channel configurations. 4/ I OX is the channel X output current, where X =, B, C, or D. 5/ V IXH is the input side logic high. 6/ V IXL is the input side logic low. 7/ CM H is the maximum common mode voltage slew rate that can be sustained while maintaining the (V OUT ) 0.8 V DD2. CM L is the maximum common mode voltage slew rate that can be sustained while maintain V OUT 0.8 V. The common mode voltage slew rates apply to both rising and falling common mode voltage edges. The transient magnitude is the range over which the common mode is slewed. 8/ Dynamic supply current is the incremental amount of supply current required for a 1 Mbps increase in signal data rate. See figures 6 through 8 for information on per channel supply current for unloaded and loaded conditions. 9/ ll voltages are relative to their respective ground V V DD1 3.6 V and V V DD2 3.6 V. Unless otherwise specified, all minimum / maximum specifications apply over the entire recommended operation range. ll typical specifications are at T = 25 C, V DD1 = V DD2 = 3.3 V. 10/ ll voltages are relative to their respective ground. For 5 V / 3.3 V operation, 4.5 V V DD1 5.5 V and V V DD2 3.6 V, and for 3.3 V / 5 V operation, V V DD1 3.6 V and 4.5 V V DD2 5.5 V. Unless otherwise specified, all minimum / maximum specifications apply over the entire recommended operation range. ll typical specifications are at T = 25 C, V DD1 = 3.3 V, V DD2 = 5 V or V DD1 = 5 V, V DD2 = 3.3 V. DL LND ND MRITIME REV PGE 16

17 Case X FIGURE 1. Case outline. DL LND ND MRITIME REV PGE 17

18 Case X continued. Symbol Inches Dimensions Millimeters Min Max Min Max b c D E E e BSC 1.27 BSC L n NOTES: 1. Controlling dimensions are millimeter, inch dimensions are given for reference only. 2. Falls within JEDEC MS-013 variation. FIGURE 1. Case outline - continued. DL LND ND MRITIME REV PGE 18

19 Device type 01 Case outline X Terminal number Terminal symbol Description 1 V DD1 Supply voltage for isolator side 1, V to 5.5 V. 2 GND1 Ground 1. Ground reference for isolator side 1. See note 1 3 V I Logic input. 4 V IB Logic input B. 5 V OC Logic output C. 6 V OD Logic output D. 7 V E1 Output enable 1. ctive high logic input. V OC and V OD outputs are enabled when V E1 is high or disconnected. V OC and V OD outputs are disabled when V E1 is low. In noisy environments, connecting V E1 to an external logic high or low is recommended. 8 GND1 Ground 1. Ground reference for isolator side 1. See note 1. 9 GND2 Ground 2. Ground reference for isolator side V E2 Output enable 2. ctive high logic input. V O and V OB outputs are enabled when V E2 is high or disconnected. V O and V OB outputs are disabled when V E2 is low. In noisy environments, connecting V E2 to an external logic high or low is recommended. 11 V ID Logic input D. 12 V IC Logic input C. 13 V OB Logic output B. 14 V O Logic output. 15 GND2 Ground 2. Ground reference for isolator side V DD2 Supply voltage for isolator side 2, V to 5.5 V. NOTE: 1. Both GND1 pins are internally connected and connecting both to GND1 is recommended. Both GND2 pins are internally connected and connecting both to GND2 is recommended. In noisy environments, connecting output enables (V E1 and V E2 ) to an external logic high or low is recommended. FIGURE 2. Terminal connections. DL LND ND MRITIME REV PGE 19

20 Positive logic V IX input V EX input V DDI state V DDO state V OX output Notes H H or NC Powered Powered H L H or NC Powered Powered L X L Powered Powered Z X H or NC Unpowered Powered H Outputs return to the input state within 1 s of V DDI power restoration. X L Unpowered Powered Z X X Powered Unpowered Indeterminate Outputs return to the input state within 1 s of V DDO power restoration if V EX state is H or NC. Outputs return to high impedance state within 8 ns of V DDO power restoration if V EX state is L. 1/ V IX and V OX refer to the input and output signals of a given channel (, B, C, or D). V EX refers to the output enable signal on the same side as the V OX outputs. V DDI and V DDO refer to the supply voltages on the input and output sides of the given channel, respectively. 2/ H is high, L is low, X is don t care, and NC is no connect. 3/ In noisy environments, connecting V EX to an external logic high or low is recommended. FIGURE 3. Truth table. DL LND ND MRITIME REV PGE 20

21 FIGURE 4. Logic diagram. DL LND ND MRITIME REV PGE 21

22 FIGURE 5. Thermal derating curve. DL LND ND MRITIME REV PGE 22

23 FIGURE 6. Typical input supply current per channel versus data rate (no load). FIGURE 7. Typical output supply current per channel versus data rate (no load). DL LND ND MRITIME REV PGE 23

24 FIGURE 8. Typical output supply current per channel versus data rate (15 pf output load). FIGURE 9. Typical VDD1 or VDD2 supply current versus data rate for 5 V and 3.3 V operation. DL LND ND MRITIME REV PGE 24

25 4. VERIFICTION 4.1 Product assurance requirements. The manufacturer is responsible for performing all inspection and test requirements as indicated in their internal documentation. Such procedures should include proper handling of electrostatic sensitive devices, classification, packaging, and labeling of moisture sensitive devices, as applicable. 5. PREPRTION FOR DELIVERY 5.1 Packaging. Preservation, packaging, labeling, and marking shall be in accordance with the manufacturer s standard commercial practices for electrostatic discharge sensitive devices. 6. NOTES 6.1 ESDS. Devices are electrostatic discharge sensitive and are classified as ESDS class 1 minimum. 6.2 Configuration control. The data contained herein is based on the salient characteristics of the device manufacturer s data book. The device manufacturer reserves the right to make changes without notice. This drawing will be modified as changes are provided. 6.3 Suggested source(s) of supply. Identification of the suggested source(s) of supply herein is not to be construed as a guarantee of present or continued availability as a source of supply for the item. DL Land and Maritime maintains an online database of all current sources of supply at Vendor item drawing administrative control number 1/ Device manufacturer CGE code Vendor part number -01XE DUM3402TRWZ-EP 1/ The vendor item drawing establishes an administrative control number for identifying the item on the engineering documentation. CGE code Source of supply nalog Devices Route 1 Industrial Park P.O. Box 9106 Norwood, M Point of contact: Raheen Business Park Limerick, Ireland DL LND ND MRITIME REV PGE 25