ACST6. Overvoltage protected AC switch. Applications. Description. Features. Benefits

Size: px

Start display at page:

Download "ACST6. Overvoltage protected AC switch. Applications. Description. Features. Benefits"

Mary Flowers
6 years ago
Views:

1 Overvoltage protected AC switch Datasheet - production data OUT TO-220AB ACST610-8T OUT Features COM G OUT COM D²PAK ACST610-8G TO-220FPAB ACST610-8FP Figure 1. Functional diagram G G OUT COM OUT I²PAK ACST610-8R Triac with overvoltage protection Low I GT (< 10 ma) TO-220FPAB insulated package: complies with UL standards (file ref: E81734) insulation voltage: 2000 V RMS G OUT COM G OUT COM Benefits Enables equipment to meet IEC High off-state reliability with planar technology Needs no external overvoltage protection Reduces the power passive component count High immunity against fast transients described in IEC standards Applications AC mains static switching in appliance and industrial control systems Drive of medium power AC loads such as: Universal motor of washing machine drum Compressor for fridge or air conditioner Description The ACST6 series belongs to the ACS/ACST power switch family built with A.S.D. (application specific discrete) technology. This high performance device is suited to home appliances or industrial systems, and drives loads up to 6 A. This ACST6 switch embeds a Triac structure and a high voltage clamping device able to absorb the inductive turn-off energy and withstand line transients such as those described in the IEC standards. The ACST610 needs only low gate current to be activated (I GT < 10 ma) and still shows a high noise immunity complying with IEC standards such as IEC (fast transient burst test). Table 1. Device summary Symbol Value Unit I T(RMS) 6 A V DRM /V RRM 800 V I GT 10 ma May 2017 DocID7297 Rev 11 1/20 This is information on a product in full production.

2 Characteristics ACST6 1 Characteristics Table 2. Absolute ratings (limiting values) Symbol Parameter Value Unit I T(RMS) I TSM On-state rms current (full sine wave) Non repetitive surge peak on-state current T j initial = 25 C, ( full cycle sine wave) TO-220FPAB T c = 92 C TO-220AB/ 6 D 2 PAK / I 2 PAK T c = 106 C D 2 PAK with 1cm 2 T copper amb = 62 C 1.5 F = 60 Hz t p = 16.7 ms 47 A F = 50 Hz t p = 20 ms 45 A I 2 t I 2 t for fuse selection t p = 10 ms 13 A 2 s di/dt Critical rate of rise on-state current I G = 2 x I GT, (t r 100 ns) F = 120 Hz T j = 125 C 100 A/µs V PP Non repetitive line peak pulse voltage (1) T j = 25 C 2 kv P G(AV) Average gate power dissipation T j = 125 C 0.1 W P GM Peak gate power dissipation (t p = 20 µs) T j = 125 C 10 W I GM Peak gate current (t p = 20 µs) T j = 125 C 1.6 A T stg Storage temperature range -40 to +150 C T j Operating junction temperature range -40 to +125 C T l Maximum lead solder temperature during 10 ms (at 3 mm from plastic case) 260 C V INS(RMS) Insulation RMS voltage (60 seconds) TO-220FPAB 2000 V 1. According to test described in IEC standard and Figure 18. A Table 3. Electrical characteristics Symbol Test conditions Quadrant T j Value Unit (1) I GT V OUT = 12 V, R L = 33 Ω I - II - III 25 C MAX. 10 ma V GT V OUT = 12 V, R L = 33 Ω I - II - III 25 C MAX. 1.0 V V GD V OUT = V DRM, R L = 3.3 kω I - II - III 125 C MIN. 0.2 V I (2) H I OUT = 500 ma 25 C MAX. 25 ma I L I G = 1.2 x I GT I - III 25 C MAX. 30 ma I L I G = 1.2 x I GT II 25 C MAX. 40 ma dv/dt (2) V OUT = 67 % V DRM, gate open 125 C MIN. 500 V/µs (di/dt) (2) c (dv/dt) c = 15 V/µs 125 C MIN. 3.5 A/ms V CL I CL = 0.1 ma, t p = 1 ms 25 C MIN. 850 V 1. Minimum I GT is guaranteed at 5% of I GT max 2. For both polarities of OUT pin referenced to COM pin 2/20 DocID7297 Rev 11

3 Characteristics Table 4. Static characteristics Symbol Test conditions Value Unit V TM (1) V T0 (1) I OUT = 2.1 A, t p = 500 µs 1.4 T j = 25 C MAX. I OUT = 8.5 A, t p = 500 µs 1.7 Threshold voltage T j = 125 C MAX. 0.9 V R d (1) Dynamic resistance T j = 125 C MAX. 80 mω I DRM I RRM V OUT = V DRM / V RRM T j = 125 C MAX. 500 µa T j = 25 C MAX. 20 µa 1. For both polarities of OUT pin referenced to COM pin V Table 5. Thermal resistances Symbol Parameter Value Unit Rt h(j-a) R th(j-c) Junction to ambient TO-220AB TO-220FPAB 60 I 2 PAK 65 Junction to ambient (soldered on 1 cm 2 copper pad) D 2 PAK 45 Junction to case for full cycle sine wave conduction TO-220FPAB 4.25 TO-220AB D 2 PAK, I 2 PAK 2.5 C/W C/W Figure 2. Maximum power dissipation versus RMS on-state current Figure 3. On-state RMS current versus case temperature (full cycle) P(W) 8 α = I T(RMS) (A) I T(RMS) (A) TO-220FPAB TO-220AB D²PAK I²PAK α = T C ( C) DocID7297 Rev 11 3/20 20

4 Characteristics ACST6 Figure 4. On-state rms current versus ambient temperature (free air convection, full cycle) Figure 5. Relative variation of thermal impedance versus pulse duration I T(RMS) (A) TO-220FPAB TO220AB I 2 PAK D 2 PAK with copper surface = 1 cm 2 α= E E-01 K = [Z th / R th ] TO-220FPAB Z th(j-c) TO-220AB D²PAK I²PAK Zth(j-a) T a ( C) t p (s) 1.0E E E E E+03 Figure 6. Relative variation of gate trigger current (I GT ) and voltage (V GT ) versus junction temperature (typical values) Figure 7. Relative variation of holding current (I H ) and latching current (I L ) versus junction temperature (typical values) I GT,V GT [T j ] / I GT,V GT [T j = 25 C ] I GT Q3 V Q 1-Q2-Q 3 GT I GT Q1-Q 2 T j ( C ) I H,I L [T j ] / I H,I L [T j = 25 C ] I L 0.5 I H T j ( C ) Figure 8. Surge peak on-state current versus number of cycles Figure 9. Non repetitive surge peak on-state current versus sinusoidal pulse width 50 I TSM (A) 1000 I TSM (A), I2t (A2s) dl /dt limitation: 100 A / μs T j initial = 25 C 40 t = 20 ms 30 Non repetitive T j initial = 25 C One cycle 100 I TS M 20 Repetitive TC =106 C Number of cycles Number of cycles t p (ms) /20 DocID7297 Rev 11

5 Characteristics Figure 10. On-state characteristics (maximum values) Figure 11. Relative variation of critical rate of decrease of main current (di/dt) c versus junction temperature I TM (A) T j max: V to = 0.90 V R d = 80 mω (dl/dt) 8 c [T j ] / (dl/dt) c [T j = 125 C] T j = 125 C T j = 25 C V TM (V) T j ( C) Figure 12. Relative variation of static dv/dt immunity versus junction temperature (gate open) Figure 13. Relative variation of leakage current versus junction temperature 6 5 dv/dt [T j ] / dv/dt [T j = 125 C] V D =V R = 536 V I DRM /I RRM [T j ;V DRM /V RRM ] / I DRM /I RRM [T j = 125 C; 800 V] 1.0E+00 V DRM =V RRM = 800V Different blocking voltages 4 1.0E-01 V DRM =V RRM = 600 V E-02 V DRM =V RRM = 200 V 1 T j ( C) T 1.0E-03 j ( C) Figure 14. Relative variation of clamping voltage (V CL ) versus junction temperature (minimum values) Figure 15. Thermal resistance junction to ambient versus copper surface under tab 1.15 V [T j ] / V CL CL [T j = 25 C] T j ( C) DocID7297 Rev 11 5/20 20

6 Application information ACST6 2 Application information 2.1 Typical application description The ACST6 device has been designed to control medium power load, such as AC motors in home appliances. Thanks to its thermal and turn off commutation performances, the ACST6 switch is able to drive an inductive load up to 6 A with no turn off additional snubber. It also provides high thermal performances in static and transient modes such as the compressor inrush current or high torque operating conditions of an AC motor. Thanks to its low gate triggering current level, the ACST6 can be driven directly by an MCU through a simple gate resistor as shown Figure 16 and Figure 17. Figure 16. Compressor control typical diagram Compressor Compressor AC Mains PTC AC Mains ACST 2 Electronic starter PTC ACST 1 3 Electronic thermostat logical circuitry Run switch ACST ACST Start switch Rg Rg Rg Power supply Gate Driver Power supply Gate Driver Compressor with integrated e-starter Compressor with external electronic drive 6/20 DocID7297 Rev 11

7 Application information Figure 17. Universal drum motor control typical diagram Universal motor Stator Rotor 12V AC Mains Motor direction setting MCU Speed motor regulation ACST Rg Vcc MCU 2.2 AC line transient voltage ruggedness In comparison with standard Triacs, which are not robust against surge voltage, the ACST6 is self-protected against over-voltage, specified by the new parameter V CL. The ACST6 switch can safely withstand AC line transient voltages either by clamping the low energy spikes, such as inductive spikes at switch off, or by switching to the on state (for less than 10 ms) to dissipate higher energy shocks through the load. This safety feature works even with high turn-on current ramp up. The test circuit of Figure 18 represents the ACST6 application, and is used to stress the ACST switch according to the IEC standard conditions. With the additional effect of the load which is limiting the current, the ACST switch withstands the voltage spikes up to 2 kv on top of the peak line voltage. The protection is based on an overvoltage crowbar technology. The ACST6 folds back safely to the on state as shown in Figure 19. The ACST6 recovers its blocking voltage capability after the surge and the next zero current crossing. Such a non repetitive test can be done at least 10 times on each AC line voltage polarity. DocID7297 Rev 11 7/20 20

8 Application information ACST6 Figure 18. Overvoltage ruggedness test circuit for resistive and inductive loads for IEC standards R = 18 Ω, L = 2 µh, Vsurge = 2 kv Rg = 220 Ω Surge generator 2kV surge Rgene Filtering unit Model of the load R L AC Mains ACST6 Rg Figure 19. Typical current and voltage waveforms across the ACST6 during IEC standard test V peak =V CL 1.2/50 µs voltage surge V 0 I peak = 120 A I 8/20 µs current surge di/dt = 150 A/µs 0 8/20 DocID7297 Rev 11

9 Ordering information scheme 3 Ordering information scheme Figure 20. Ordering information scheme ACS T G TR AC switch Topology T = Triac On-state rms current 6 = 6 A Triggering gate current 10 = 10 ma Repetitive peak off-state voltage 8 = 800 V Package FP = TO-220FPAB T = TO-220AB R = I²PAK G = D²PAK Delivery mode TR = Tape and reel Blank = Tube DocID7297 Rev 11 9/20 20

10 Package information ACST6 4 Package information Epoxy meets UL94, V0 Cooling method: by conduction (C) Recommended torque value (TO220AB, TO220FPAB): 0.4 to 0.6 N m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: ECOPACK is an ST trademark. 10/20 DocID7297 Rev 11

11 Package information 4.1 TO-220AB package information Figure 21. TO-220AB package outline Resin gate 0.5 mm max. protrusion (1) (1) Resin gate accepted in one of the two positions or in the symmetrical opposites DocID7297 Rev 11 11/20 20

12 Package information ACST6 Ref. Table 6. TO-220AB package mechanical data Millimeters Dimensions Inches Min. Max. Min. Max. A b b c D D typ typ. E e e F H J L L L typ typ. L typ typ. θp Q /20 DocID7297 Rev 11

13 Package information 4.2 TO-220FPAB package information Figure 22. TO-220FPAB package outline DocID7297 Rev 11 13/20 20

14 Package information ACST6 Table 7. TO-220FPAB package mechanical data Dimensions Ref. Millimeters Inches Min. Max. Min. Max. A B D E F F F G G H L2 16 Typ Typ. L L L L L Diam /20 DocID7297 Rev 11

15 Package information 4.3 D 2 PAK package information Figure 23. D 2 PAK package outline DocID7297 Rev 11 15/20 20

16 Package information ACST6 Ref. Table 8. D 2 PAK package mechanical data Millimeters Dimensions Inches Min. Max. Min. Max. A A A B B C C D E G L L L M R 0.40 typ typ. V Figure 24. Footprint (dimensions in mm) /20 DocID7297 Rev 11

17 Package information 4.4 I 2 PAK package information Figure 25. I 2 PAK package outline DocID7297 Rev 11 17/20 20

18 Package information ACST6 Ref. Table 9. I 2 PAK package mechanical data Millimeters Dimensions Inches Min. Max. Min. Max. A A B B C C D E G L L L /20 DocID7297 Rev 11

19 Ordering information 5 Ordering information Table 10. Ordering information Order code Marking Package Weight Base Qty Packing mode ACST610-8FP TO-220FPAB 2.4 g 50 Tube ACST610-8G D 2 PAK 1.5 g 50 Tube ACST610-8GTR ACST6108 D 2 PAK 1.5 g 1000 Tape and reel ACST610-8R I 2 PAK 2.3 g 50 Tube ACST610-8T TO-220AB 1.5 g 50 Tube 6 Revision history Table 11. Document revision history Table 12. Date Revision Changes Jan F Previous issue. 09-May Layout update. No content change. 18-Dec Document structure and parameter presentation revised for consistency with other ACST documents. No technical changes. Order codes updated. 01-Jul Updated Figure May Updated features in cover page and Table 2. Updated Section 4: Package information. Minor text changes. DocID7297 Rev 11 19/20 20

20 IMPORTANT NOTICE PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries ( ST ) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document STMicroelectronics All rights reserved 20/20 DocID7297 Rev 11

ACST1635-8FP. Overvoltage protected AC switch. Description. Features. Applications

ACST1635-8FP. Overvoltage protected AC switch. Description. Features. Applications Overvoltage protected AC switch Description Datasheet production data Features OUT COM TO-220FPAB Enables equipment to meet IEC 61000-4-5 surge with overvoltage crowbar technology High noise immunity against