Description: RJ45 1X4 Tab Up Through Hole, Long Body 2.5G Base-T Contact Area : 50μ" min. Gold LED:L-Yellow;R-Green PoE 60W & Light Pipe

Size: px

Start display at page:

Download "Description: RJ45 1X4 Tab Up Through Hole, Long Body 2.5G Base-T Contact Area : 50μ" min. Gold LED:L-Yellow;R-Green PoE 60W & Light Pipe"

Louise Simon
5 years ago
Views:

1 To: Customer P/N: UDE P/N: Description: RJ45 1X4 Tab Up Through Hole, Long Body 2.5G Base-T Contact Area : 50μ" min. Gold LED:L-Yellow;R-Green PoE 60W & Light Pipe Spec No. Update Date Revision RTK /4/10 C Approved Checked Prepared

2 1. MECHANICAL DIMENSION 1.1 Product Dimension Unit : mm General Tolerance : X.X : ± 0.38 X.XX : ±

3 1.2 Recommended PCB Layout Component Side of Board All dimension tolerances are ±0.05mm unless otherwise specified - 2 -

4 Table1 Layer Layout Trace component Grounding Test Point Via Hole PTH NPTH Component side X X O X X X O Inner layer O NA O NA O X O Bottom side O O O O O X O X--Forbid; O--OK; NA--Not Applicable. 1.3 Recommended panel cutout 1.4 Packing Information 16 pcs finished goods per tray 7 trays(112pcs finished goods) per inner box 4 Inner boxes(448 pcs finished goods) per master carton - 3 -

5 1.5 Standard RJ45 Plug Specification - All dimensions follow : FCC subpart F, 68,500, Figure (C)(2)(i) & (C)(2)(ii) & (C)(3)(i) IEC All plugs must be meeting the requirements of plug Go & No-Go gauge. Gauge follow : FCC subpart F, 68,500, Figure (C)(4)(i) & (C)(5)(i) - There must be no damage to Housing and Locking Latch. - There must be no nicks and cuts in cable. - Durability : 750 cycles generally - 4 -

6 2. REQUIREMENTS 2.1 Design and Construction Product shall be of design, construction and physical dimensions specified on applicable. 2.2 Material Terminal Parts (Underplating : 50μ"min Nickel overall) RJ Terminal : Phosphor Bronze, Thickness=0.30mm Finish : Contact Area : 50μ" min. Gold Input Terminal : Brass, Thickness=0.35mm Finish : 100μ" min.bright Tin Case Terminal : Brass, Thickness=0.30mm Finish : 100μ" min. Bright Tin Plastic Parts <UL94V-0> Housing : PA6T, Black Case : PA6T, Black Spacer : PBT, Black Holder : PBT, Black Light Pipe : PC, Transparent Shield Parts Front Shield : Stainless Steel, Thickness=0.20mm, unplating Back Shield : Stainless Steel, Thickness=0.20mm, Pre-soldering - 5 -

7 2.3 Operating and Storage Temperature Operating Temperature : 0 C to +70 C Storage Temperature : -40 C to +85 C 2.4 RJ45 specifications Insulation Resistance :500MΩ min. Insertion force with the latch depressed :22N max Removal force with the latch depressed : 44N max Locking Force of Plug Latch : 50N 60+/-5 sec Durability : 2500 cycles 2.5 Performance and Test Description Product is designed to meet electrical, mechanical and environmental performance requirements specified in below table. All tests are performed at ambient environmental conditions per MIL-STD-1344A and EIA-364 unless otherwise specified. 2.6 Packaging and Packing All parts shall be packaged and packed to protect against physical damage corrosion and deterioration during shipment and storage

8 3. ELECTRICAL Schematic PHY Side (Input) TD1+ R11 TCT1 R12 1:1 22nFx4 75Ω Cable Side (RJ45 Output) C1 TX1+ TD1- R10 C2 TX1- TD2+ R4 TCT2 R6 1:1 75Ω C3 TX2+ TD2- R5 C6 TX2- TD3+ R3 TCT3 R1 1:1 75Ω C4 TX3+ TD3- R2 C5 TX3- TD4+ R8 TCT4 R7 1:1 75Ω C7 TX4+ TD4- R9 C8 TX4- VC1 R13 VC2 R14 2KV 1000pF VC3 R15 VC4 R16 Shield L3 L1 Yellow Green L4 L2 Emitting Color λp (nm) Green ~2.6 V Yellow ~2.6 V 10μA max. 10μA max

9 3.2 Transmitter filter & Receiver filter Type : Balance low pass 100Ω impedance Insertion Loss 1-50MHz -0.5 db Max MHz -1.0 db Max 3.3 Return Loss 1~40MHz -20 db Min load 100Ω MHz *log(Freq MHz/40MHz) db Min load 100Ω 3.4 Reflected CM to Diff Conversion(REF) 1MHZ 50MHZ 100MHZ 200MHZ -30 db Min -30 db Min -27 db Min -24 db Min 3.5 CM to DM Conversion(REF) 1-125MHZ -35 db Min 3.6 Reflected Diff to CM Conversion(REF) 1-10MHZ -48 db Min MHz *log(Freq MHz/10MHz) db Min 3.7 CM to CM Attenuation (REF) 1-200MHZ -25 db Min 3.8 Cross Talk (REF) MHz -30 db Min MHz -25 db Min - 8 -

10 mV, 11mA DC bias Input (R11-R10), Input(R4-R5), Input (R3-R2), Input(R8-R9): 150 μh min HiPot Test Input (R11-R10) To Output(C1-C2) : 1500Vac 60s or 2250Vdc 60s Input (R4-R5) To Output(C3-C6) : 1500Vac 60s or 2250Vdc 60s Input (R3-R2) To Output(C4-C5) : 1500Vac 60s or 2250Vdc 60s Input (R8-R9) To Output(C7-C8) : 1500Vac 60s or 2250Vdc 60s 3.11 Balanced DC line current 720mA continus 1.2A for 200milliseconds - 9 -

11 4. DIPPING TEMPERATURE PROFILE

12 5. Revision History Issue Date Revision Comments Operator 2016/9/1 A Initial Release. Max 2016/12/22 B Update Product Drawing Max 2017/4/10 C Update Layout Max

POE 60W & Light Pipe

To: Customer P/N: UDE P/N: Description: RJ45 1X1 Tab Up Through Hole, Long Body 2.5G Base-T Contact Area : 30μ'' Min. Gold LED: L-Green/Yellow; R-Green/Yellow POE 60W & Light Pipe 100% RoHS material,without