TNC SERIES General... 4 Interface... 5 Characteristics...6-7
|
|
|
- Sara Lawrence
- 5 years ago
- Views:
Transcription
1
2 CONTENTS PAGE TNC SERIES General... 4 Interface... 5 Characteristics TNC 50 Ω SERIES Plugs Jacks...0- Jacks and receptacles... Receptacles...-4 Adapters... 5 Caps... 6 TNC 75 Ω SERIES Plugs... 7 Jacks and adapters... 8 TNC 8 GHz SERIES Characteristics... 9 Plugs and jacks... 0 Jacks... Receptacles... Adapters and cap... Panel drilling... 4 Assembly instructions
3 GENERAL 50 Ω 75 Ω DC - GHz standard DC - 8 GHz 8 GHz series DC -.5 GHz DC - GHz recommended 50 and 75 Ω DC -.5 GHz commercial GENERAL Screw-on equivalent to BNC bayonet series Good RF performance Suitable for high power levels Long life and high strength ranges: - Standard TNC series (50 and 75 Ω fully intermatable) - Commercial TNC series (50 and 75 Ω) - 8 GHz TNC series (50 Ω) APPLICABLE STANDARDS MIL-C-90 / MIL STD 48A/ IEC CECC 00 APPLICATIONS Avionics Aeronautics Countermeasures Telecommunications -4
4 INTERFACE PLUG JACK LETTER mm inch mm inch LETTER min. max. min. max. min. max. min. max. A A B B D C E D F E G F H
5 CHARACTERISTICS STANDARD TNC TEST/CHARACTERISTICS MIL-C-90 A VALUES/REMARKS ELECTRICAL CHARACTERISTICS Impedance 50 Ω 75 Ω Frequency range DC - GHz DC -.5 GHz V.S.W.R max Insertion loss db max at 9 GHz RF leakage db min from to GHz Insulation resistance MΩ min Contact resistance center contact (mω) outer contact (mω) -6 Initial.5 0. After proof - Working voltage At sea level: 500 V rms at ft (000 m): 5 V rms Dielectric withstanding voltage -7 At sea level: 500 V rms at ft (000 m): 75 V rms RF withstanding voltage - At sea level: 000 V rms (5 MHz sine wave) MECHANICAL CHARACTERISTICS Durability matings Mating / unmating axial force: not applicable torque:.96 inch pounds (.6 N.cm) Recommended mating torque.99 to 5.98 inch pounds (46 to 69 N.cm) Proof torque 4.74 inch pounds (70 N.cm) Coupling mechanism retention force Lbf (44.5 dan) Cabling retention force -4 cable clamp: 40.6 Lbf (8 N min) (all cables) crimped: 5 Lbf (7 N min) (cable dia..89 (4.8) to.8 (5.8)) 76.4 Lbf (40 N min) (cable dia..50 (6.5) and above) Center contact retention Axial: 6.06 Lbf (7 N) ENVIRONMENTAL CHARACTERISTICS Temperature range standard models -65 C / + 65 C hermetic sealed models -65 C / +00 C models for semi-rigid cables -65 C / +05 C Thermal shock -0 MIL-STD-0, method 07, condition B High temperature endurance MIL-STD-0, method 08 Corrosion (salt spray) - MIL-STD-0, method 0, condition B Vibrations -8 MIL-STD-0, method 04, condition B Shocks -9 MIL-STD-0, method, condition G Moisture resistance - MIL-STD-0, method 06 Low pressure - Not applicable Hermetic seal Applied vacuum 0-6 mm of Hg (Torrs) leakage rate < 0-6 atm/cm /s Leakage Pressure.5 bars; duration mn; temperature 5 C to 5 C MATERIALS Body and center pin contact Center socket contact Ferrules Insulators Gaskets PLATING Body Center contacts Brass as per QQ-B-66 Beryllium copper as per QQ-C-50 Brass PTFE teflon Silicone elastomer Nickel plated Gold plated All dimensions are given in mm -6
6 CHARACTERISTICS COMMERCIAL TNC TEST/CHARACTERISTICS VALUES/REMARKS ELECTRICAL CHARACTERISTICS Impedance 50 Ω 75 Ω Frequency range DC -.5 GHz Test voltage 500 V rms Operating voltage 500 V rms Insulation resistance 5000 mω min (500 V) Contact resistance 0 mω max ENVIRONMENTAL CHARACTERISTICS Temperature range 5 C / + 70 C PLATING Body Center contacts Nickel Gold -7
7 50 Ω PLUGS STRAIGHT PLUGS CRIMP TYPE FOR FLEXIBLE CABLE Fig. Fig. Fig. Cable group Fig.6 / 50 S 5 / 50 S R R R R Dimensions (mm) A B C D Captive center contact yes Assembly instructions M 0 M 0 5 / 50 S R no M / 50 D R M 0 yes 6 / R M 05 Packaging 00 pieces unit Note commercial version full crimp commercial version, full crimp STRAIGHT PLUGS CLAMP TYPE FOR FLEXIBLE CABLE Fig. Fig. Cable group Fig..6 / R Dimensions (mm) A B C Captive center contact Assembly instructions Packaging yes M 06 Unit 5 / 50 S + D R no M pieces 6 / R M 07 yes 0 + / 50 R M 07 Unit Note conical braid clamp -8
8 50 Ω PLUGS STRAIGHT PLUG CLAMP TYPE FOR SEMI RIGID CABLE Cable group Captive center contact Assembly instructions Packaging.4 R no M 08 Unit RIGHT ANGLE PLUGS CRIMP TYPE FOR FLEXIBLE CABLE Fig. Fig. Fig. Cable group Fig. Captive center contact Assembly instructions Packaging Note.6 / 50 S R / 50 S M 04 R4 8 6 yes M pieces R M 0 unit commercial version RIGHT ANGLE PLUG CLAMP TYPE FOR FLEXIBLE CABLE Cable group Captive center contact Assembly instructions Packaging 5 / 50 S + D R yes M 07 Unit -9
9 50 Ω JACKS STRAIGHT JACKS CRIMP TYPE FOR FLEXIBLE CABLE Fig. Fig. Cable group Fig Captive center contact Assembly instructions Packaging Note.6 / 50 S + D R yes M0 Unit 5 / 50 S R4 5 6 yes M0 00 pieces commercial version, full crimp STRAIGHT BULKHEAD JACKS CRIMP TYPE FOR FLEXIBLE CABLE (REAR MOUNT) Cable group Dimensions (mm) A B C D Captive center contact Assembly instructions Panel drilling Packaging Note.6 / 50 S R M0 commercial version, panel sealed yes 5 / 50 S R M0 P09+P 00 pieces commercial version, panel sealed, full crimp -0
10 50 Ω JACKS STRAIGHT JACK CLAMP TYPE FOR FLEXIBLE CABLE Cable group Captive center contact Assembly instructions Packaging 5 / 50 S R no M07 Unit STRAIGHT SQUARE FLANGE JACKS CLAMP TYPE FOR FLEXIBLE CABLE Cable group Also for screws type -56 UNF A Dimensions (mm) A B C Captive center contact Assembly instructions.6 / R yes M06 5 / 50 S + D R no M07 Panel drilling P04 Packaging Unit 7.5 mm SQUARE FLANGE STRAIGHT JACK SOLDER TYPE FOR SEMI RIGID CABLE Cable group Captive center contact Assembly instructions Panel drilling Packaging.085 R no M P0 Unit -
11 50 Ω JACKS & RECEPTACLES STRAIGHT BULKHEAD JACKS PANEL SEALED REAR MOUNT Cable group Dimensions (mm) A B Captive center contact Assembly instructions Panel drilling Packaging.6 / 50 R M 00 pieces yes P09 5 / 50 S R M07 Unit 7.5 mm SQUARE FLANGE STRAIGHT FEMALE RECEPTACLES Dimension A (mm) Captive center contact Panel drilling Packaging Note R M.5 x 0.45 unit yes P05 Solder pot R pieces -
12 50 Ω RECEPTACLES 9 mm SQUARE FLANGE STRAIGHT FEMALE RECEPTACLE Captive center contact Panel drilling Packaging Note R no P0 Unit Slotted contact HOLES FLANGE STRAIGHT FEMALE RECEPTACLE Captive center contact Panel drilling Packaging Note R yes P07 Unit Solder pot contact BULKHEAD STRAIGHT FEMALE RECEPTACLES Fig. Fig. Fig Captive center contact Panel drilling Packaging Note R P08 yes R P0 Unit Front mount, solder pot contact Panel sealed, front mount, solder pot contact -
13 50 Ω RECEPTACLES 7.5 mm SQUARE FLANGE RIGHT ANGLE FEMALE RECEPTACLE Captive center contact Panel drilling Packaging Note R yes P06 Unit Solder pot contact RIGHT ANGLE BULKHEAD FEMALE RECEPTACLE Captive center contact Panel drilling Packaging Note R yes P08 Unit Panel sealed, front mount, solder pot contact 7.5 mm SQUARE FLANGE STRAIGHT MALE RECEPTACLE Captive center contact Panel drilling Packaging Note R yes P0 Unit Solder pot contact -4
14 50 Ω IN SERIES ADAPTERS IN SERIES ADAPTERS Fig. Fig. Fig. Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Captive center contact Fig Panel drilling Packaging Note R yes R Unit Male-male R Female-female R R R R P0 P09 00 pieces Square flange femalefemale Square flange slide on type male-female Bulkhead hermetic, panel sealed female-female Commercial version, bulkhead female-female Right angle male-female R unit Female female male R Female female female -5
15 50 Ω CAPS PROTECTIVE CAPS Fig. Fig. Fig. Fig. Finish Packaging Note R Black chromium Male with cord Unit R Male with chain Nickel R pieces Female with chain -6
16 75 Ω PLUGS STRAIGHT PLUGS CRIMP TYPE FOR FLEXIBLE CABLE Cable group Captive center contact 6 / Assembly instructions Packaging R no Unit Full crimp M0 R yes 00 pieces Commercial version - full crimp Note STRAIGHT PLUG CLAMP TYPE FOR FLEXIBLE CABLE Cable group Captive center contact Assembly instructions Packaging 8 / 75 R yes M09 Unit -7
17 75 Ω JACKS AND ADAPTERS STRAIGHT BULKHEAD JACKS CRIMP TYPE FOR FLEXIBLE CABLE Cable group Captive center contact Panel drilling 6 / R no Assembly instructions Packaging P09 or P M0 R yes 00 pieces Unit Note Panel sealed Commercial version - panel sealed STRAIGHT BULKHEAD JACK, CRIMP TYPE, FOR FLEXIBLE CABLE Cable group Captive center contact Assembly instructions Panel drilling Packaging Note 6 / 75 R yes M07 P09 Unit Panel sealed IN SERIES ADAPTERS Fig. Fig. Fig Captive center contact Packaging R yes Unit R
18 8 GHz CHARACTERISTICS TEST/CHARACTERISTICS MIL-C-90 A VALUES/REMARKS ELECTRICAL CHARACTERISTICS Impedance Frequency range MECHANICAL CHARACTERISTICS Durability matings Mating / unmating Axial force: not applicable Torque:.96 inch pounds (.6 N.cm) Recommended mating torque.98 inch pounds (65 N.cm) Proof torque 9.40 inch pounds (9 N.cm) Coupling mechanism retention force Lbf (44.5 dan) Cabling retention force -4 5 Lbf (7 N min) (cable dia..89 (4.8) to.8 (5.8)) 76.4 Lbf (40 N min) (cable dia..50 (6.5) and above) Center contact retention Axial: 6.06 Lbf (7 N) ENVIRONMENTAL CHARACTERISTICS Temperature range 50 Ω DC - 8 GHz V.S.W.R. -4 Semi rigid cable:.7 max Flexible cable:.5 at.4 GHz Insertion loss db max at 9 GHz RF leakage db min from to GHz Insulation resistance MΩ min Contact resistance center contact (mω) outer contact (mω) -6 Initial.5 0. In series adapter:.5 max After proof - Working voltage At sea level: 500 V rms at ft (000 m): 5 V rms Dielectric withstanding voltage -7 At sea level: 500 V rms at ft (000 m): 75 V rms RF withstanding voltage - At sea level: 000 V rms (5 MHz sine wave) Standard models Hermetic sealed models Models for semi rigid cables 65 C / + 65 C 65 C / +00 C 65 C / +05 C Combined climate tests Thermal shock -0 MIL STD 0, method 07, condition B High temperature endurance MIL STD 0, method 08 Corrosion (salt spray) - MIL STD 0, method 0, condition B Vibrations -8 MIL STD 0, method 04, condition B Shocks -9 MIL STD 0, method, condition G Moisture resistance - MIL STD 0, method 06 Low pressure - Not applicable Hermetic seal Applied vacuum 0-6 mm of Hg (Torrs) Leakage rate < 0-6 atm/cm /s Leakage Pressure.5 bars; duration mn; temperature 5 C to 5 C MATERIALS Body Center contact Ferrules Insulators Gaskets PLATING Body Center contacts male female Stainless steel Brass Bronze Brass PTFE teflon Silicone elastomer Passivated Gold plated Standard packaging = unit All dimensions are given in mm (inch) -9
19 8 GHz PLUGS AND JACKS STRAIGHT PLUGS CRIMP TYPE FOR FLEXIBLE CABLE Dimensions mm(inch) Cable group A B C D 5 / 50 D R (.8).05 (04). (.6) 5.5 (.8) / 50 R (.78).45 (.096) 7.5 (.95).05 (.45) Assembly instructions M 0 STRAIGHT PLUGS SOLDER TYPE FOR SEMI-RIGID CABLE Dimensions mm(inch) Cable group A B C Assembly instructions.4 R (.09).65 (.44) 5 (.97) M.50 R (.067) 6.45 (.54) 8 (.5) M 4 STRAIGHT JACKS SOLDER TYPE FOR SEMI-RIGID CABLE Dimensions mm(inch) Cable group A B C Assembly intructions.4 R (.09).65 (.4) 5 (.97) M.50 R (.067) 6.45 (.54) 8 (.5) M 4-0
20 8 GHz JACKS STRAIGHT SQUARE FLANGE JACK CRIMP TYPE FOR FLEXIBLE CABLE Cable group Panel drilling Assembly instructions 5 / 50 D R P0 M 0 STRAIGHT SQUARE FLANGE JACKS SOLDER TYPE FOR SEMI-RIGID CABLE Dimensions mm(inch) Cable group Panel drilling Assembly instructions A B C D.4 R (.5) (.09).65 (.44) 5 (.97) M P.50 R (.46).7 (.067) 6.45 (.54) 8 (.5) M 4 STRAIGHT BULKHEAD JACKS SOLDER TYPE FOR SEMI-RIGID CABLE Dimensions mm(inch) Cable group A B C Panel drilling Assembly intructions.4 R4 700 (.09).65 (.44) 5 (.97) M P09.50 R (.067) 6.45 (.54) 8 (.5) M 4 -
21 8 GHz RECEPTACLES SQUARE FLANGE STRAIGHT MALE RECEPTACLE (extended dielectric - stub contact) Captive center contact Panel drilling R yes P4 SQUARE FLANGE STRAIGHT FEMALE RECEPTACLE Captive center contact Panel drilling R yes P5 SQUARE FLANGE STRAIGHT FEMALE RECEPTACLE (extended dielectric - stub contact) Captive center contact Panel drilling R yes P R no -
22 8 GHz ADAPTERS AND CAP IN SERIES ADAPTERS Fig. Fig. Fig. Fig. 4 Fig. 5 Fig. Captive center contact Panel drilling Note R Male - male R Female - female R yes Male - female R P6 Square flange female - female R P09 Bulkhead panel sealed female - female SHORT CIRCUIT CAP R
23 PANEL DRILLING P0 P0 P0 P04 P05 P06 P07 P08 P09 P0 P P P P4 P5 P6-4
24 ASSEMBLY INSTRUCTIONS M 0 Centre contact STRIPPING DIMENSIONS Ferrule Heatshrink sleeve (option) Body Stripping length (mm) Crimp tools a b c e Dies included MIL standard R (M50/5-0) + dies R R8 000 Hex R8 5 0 (M50/5-) Hex Slide the heatshrink sleeve onto the cable (option). - Slide the ferrule onto the cable. - Strip the cable. 4 - Slide the cable into the body until it bottoms against the insulator. - Slide the center contact on until it bottoms against the cable dielectric. - Solder the center contact. - Clean solder area. 5 - Slide the ferrule over the braid. - Crimp the ferrule with crimping tool (see table). - Fan the braid. 6 - Cut the excess of braid if necessary. - Slide the sleeve over the ferrule and heatshrink it in place (option). -5
25 ASSEMBLY INSTRUCTIONS M 0 Ferrule Centre contact STRIPPING DIMENSIONS Body Heatshrink sleeve (option) Stripping length (mm) Crimp tools a b c e Dies included MIL standard R (M50/5-0) + dies R R R8 000 Hex R R8 5 0 (M50/5-) Hex R R8 000 Hex R8 000 Hex 0.54 R R4 5 6 R4 6 R R R R R8 000 Hex R8 5 0 (M50/5-) Hex R8 5 0 (M50/5-) Hex Slide the heatshrink sleeve onto the cable (option). - Slide the ferrule onto the cable. - Strip the cable. 4 - Slide the cable into the body until it bottoms against insulator. - Slide the center contact on until it bottoms against the cable dielectric. - Crimp the center contact with crimping tool (see table). 5 - Slide the ferrule over the braid. - Crimp the ferrule with crimping tool (see table). - Fan the braid. 6 - Cut the excess of braid if necessary. - Slide the sleeve over the ferrule and heatshrink it in place (option). -6
26 ASSEMBLY INSTRUCTIONS M 0 Clamp braid Centre contact STRIPPING DIMENSIONS Ferrule Insulator Body R R R R4 6 Stripping length (mm) Crimp tools a b c e Dies included MIL standard R (M50/5-0) + dies R8 000 Hex R8 5 0 (M50/5-) Hex Slide the ferrule onto the cable. - Strip the cable. 4 - Slide cable into body until it bottoms against insulator. - Fan the braid. - Slide the braid clamp and the insulator between the dielectric and the braid. - Slide the insulator between the dielectric and the braid. 5 - Slide the ferrule over the braid. - Slide on the center contact until it bottoms against the cable dielectric. - Solder or crimp the center contact with crimping tool (see table). - Clean solder area if necessary. 6 - Crimp the ferrule with crimping tool (see table). - Cut the excess of braid if necessary. -7
27 ASSEMBLY INSTRUCTIONS M 04 Cap STRIPPING DIMENSIONS Ferrule Body Heatshrink sleeve (option) Stripping length (mm) Crimp tools a b c e Dies included MIL standard R (M50/5-0) + dies R R8 000 Hex.5 R (M50/5-0) Hex.5 R R8 000 Hex 5.4 R8 5 0 (M50/5-) Hex Slide the heatshrink sleeve onto the cable (option). - Slide the ferrule onto the cable. - Strip the cable. 4 - Crimp the ferrule with crimping tool (see table). - Solder the inner conductor. - Fan the braid. 5 - Place the cap into the body. - Push the connector body under the braid. - Slide the ferrule over the braid. 6 - Press on the cap flush or slightly below the surface of the body assembly. - Slide the sleeve over the ferrule and heatshrink it in place (option). -8
28 ASSEMBLY INSTRUCTIONS M 05 Back nut Centre contact STRIPPING DIMENSIONS Heatshrink sleeve (option) Ferrule Body Stripping length (mm) Crimp tools a b c e Dies included MIL standard R (M50/5-0) + dies R R8 000 Hex R8 5 0 (M50/5-0) Hex R R8 000 Hex R8 5 0 (M50/5-) Hex Slide the heatshrink sleeve onto the cable (option). - Slide the ferrule onto the cable. - Position the ferrule's hole at the front if soldering. - Position the ferrule's hole at the back if crimping. - Strip the cable Slide the center contact on until it bottoms against the insulator back nut. - Solder or crimp the contact (see table). - Fan the braid. - Slide the cable into the back nut. 5 - Screw the back nut into the connector body with the adapted wrench. - Recommended coupling torque (see table). - Slide the ferrule over the braid. - Crimp the ferrule with crimping tool (see table). 6 - Slide the sleeve over the ferrule and heatshrink it in place (option). -9
29 ASSEMBLY INSTRUCTIONS M 06 Insulator Centre contact Gasket STRIPPING DIMENSIONS Clamp braid Back nut Body R R Stripping length (mm) Coupling torque a b c e N.cm - Slide the back nut onto the cable. - Strip the cable. - Cut slots in the jacket if necessary. 4 - Solder the center contact onto the inner conductor. - Slide the back nut over the cable assembly. - Slide the clamp braid sleeve between the cable dielectric and the braid. 5 - Mount the gasket into the body. - Cut the braid flush with the clamp braid sleeve. - Slide the spacer onto the cable. - Slide the center contact on until it bottoms against the cable dielectric. 6 - Screw sub-assembly into the connector body with the adapted wrench. - Recommended coupling torque (see table). -0
30 ASSEMBLY INSTRUCTIONS M 07 Washer V groove gasket Centre contact STRIPPING DIMENSIONS Back nut Clamp braid Body Stripping length (mm) a b e R R R R R Coupling torque 450 N.cm N.cm R R R N.cm - Strip the cable as shown in sketch. 4 - Slide the back nut over the cable assembly. - Slide the center contact onto the inner conductor. - Slide the back nut, the washer and the 'V' groove gasket onto the cable. 5 - Slide the clamp braid sleeve over the braid. - Solder the center contact onto the inner conductor. - Fold the braid back and trim off the extra braid. - Trim dielectric back as shown in sketch. 6 - Screw sub-assembly into the connector body with the adapted wrench. - Recommended coupling torque (see table). -
31 ASSEMBLY INSTRUCTIONS M 08 V groove gasket Clamp braid Solder barrel Centre contact STRIPPING DIMENSIONS Insulator Washer Back nut Body We recommend a cable thermal preconditioning before assembly Stripping length b (mm) Coupling torque R N.cm - Strip the cable. - Trim the cable inner conductor. - Clean the cable. 4 - Slide the insulator onto the cable inner conductor. - Slide the center contact on until it bottoms against the insulator. - Slide the back nut, the washer, the 'V' groove gasket, the clamp braid sleeve and the solder barrel onto the cable. 5 - Solder the center contact onto the inner conductor. - Assemble the components. - Position the solder barrel and the cable flush against the solder barrel gauge. - Solder the solder barrel onto the cable. - After cooling, remove the solder barrel gauge. 6 - Screw sub-assembly into the connector body with the adapted wrench. - Recommended coupling torque (see table). Gauge -
32 ASSEMBLY INSTRUCTIONS M 09 Clamp nut Washer Gasket Centre contact Body Braid clamp sleeve STRIPPING DIMENSIONS b Stripping length (mm) a b e R Strip the cable. - Solder the cable inner conductor into center contact. Solder - Slide the clamp nut, the washer and the gasket onto the cable. - Slide clamp braid sleeve over braid. - Fold back braid and trim off surplus braid. - Trim back dielectric as shown. 4 - Screw sub-assembly into the connector body. Recommended coupling torque 450 N.cm. e a Hex.:.6 /flats -
33 ASSEMBLY INSTRUCTIONS M 0 Ferrule Back body Centre contact Body STRIPPING DIMENSIONS b a c e Stripping length (mm) Crimp tools a b c e Dies included MIL standard R (M50/5-0) + dies R R8 000 Hex R8 5 0 (M50/5-) Hex Slide onto the cable the ferrule. - Strip the cable. - Crimp the ferrule with crimping tool. - Slide on the center contact until it bottoms against insulator. - Crimp center contact with crimping tool. Crimp area Crimp area - Fan the braid. - Slide the back body between dielectric and braid. - Slide ferrule over the braid (in direction F). 4 - Mount gasket into connector. - Screw sub-assembly into the connector body (recommended coupling torque 450 N.cm in.lb). Ferrule F Hex.: mm/flats -4
34 ASSEMBLY INSTRUCTIONS M Clamp nut Clamp braid sleeve Gasket Spacer Centre contact Body STRIPPING DIMENSIONS b c e a Stripping length (mm) a b c e R Slide clamp nut onto cable. - Strip the cable. - Cut slots in the jacket if necessary. - Solder center contact onto cable center conductor. - Slide back nut over clamp assembly. Solder - Slide the clamp braid sleeve between cable dielectric and braid. - Cut the braid flush with the clamp braid sleeve. - Slide the spacer onto the cable. 4 - Mount gasket into connector. - Screw sub-assembly into the connector body (recommended coupling torque 450 N.cm in.lb). Hex.: mm/flats -5
35 ASSEMBLY INSTRUCTIONS M Centre contact Insulator Body STRIPPING DIMENSIONS a Stripping length a (mm) Positioner R R Strip the cable. - Clean the cable. - Screw positioner onto connector. - Slide sub-assembly into the connector body (in direction F). Body F - Slide insulator onto the cable center conductor. - Solder center contact onto cable center conductor. - Clean solder area. 4 - Solder the cable into body of connector. - After cooling remove positioner and clean soldered area. Solder Solder -6
36 ASSEMBLY INSTRUCTIONS M Body Insulator Centre contact Solder sleeve Distance-piece STRIPPING DIMENSIONS We recommend a thermal preconditionning cable R R R R4 700 Stripping length a (mm) Center contact positioner Cable positioner Soldering jig Solder gauge thickness 0.5 mm Milling cutter Lock jig Torque wrench R R R R R R R Strip the cable with the cable stripping tool. - Trim the cable inner conducteur with the trimmer. - Clean the cable. - Screw the positioner onto the soldering jig. - Slide the cable assembly until it bottoms against positioner. - Tighten and solder the contact. Tighten Centre contact Gauge - After cooling, remove the assembly from the jig. - Trim dielectric recess with the milling cutter. Milling cutter Solder sleeve Cable Cable 4 - Slide the distance-piece on the solder sleeve. - Slide insulator on the center contact. Positioner Soldering jig - After cooling remove cable assembly from the jig. - Slide positioner into the solder sleeve. - Get in solder sleeve assembly onto the soldering jig and slide the cable until it bottoms against positioner. - Tighten. - Put rings of solder around the cable and solder. Tighten Cable in position 5 Insulator Distance-piece Center contact Solder sleeve - Slide the connector on the sleeve and lock it. Lock jig Solder Solder sleeve Positioner Soldering jig -7
37 ASSEMBLY INSTRUCTIONS M 4 Body Insulator Centre contact Solder sleeve Distance-piece STRIPPING DIMENSIONS We recommend a thermal preconditionning cable R R R R4 700 Stripping length a (mm) Stripping tool Trimmer Center contact positioner Soldering jig Cable positioner Milling cutter Lock jig Torque wrench R R R R R R R Or tool box for TNC 8 for semi rigid cable R8 00 R Strip the cable with the cable stripping tool. - Trim the cable inner conducteur with the trimmer. - Clean the cable. - Screw the positioner onto the soldering jig. - Slide the cable assembly until it bottoms against positioner. - Tighten and solder the contact. Tighten Centre contact Gauge - After cooling, remove the assembly from the jig. - Trim dielectric recess with the milling cutter. Milling cutter Solder sleeve Cable Cable 4 - Slide the distance-piece on the solder sleeve. - Slide insulator on the center contact. Positioner Soldering jig - After cooling remove cable assembly from the jig. - Slide positioner into the solder sleeve. - Get in solder sleeve assembly onto the soldering jig and slide the cable until it bottoms against positioner. - Tighten. - Put rings of solder around the cable and solder. Tighten Cable in position 5 Insulator Distance-piece Center contact Solder sleeve - Slide the connector on the sleeve and lock it. Lock jig Solder Solder sleeve Positioner Soldering jig -8
SECTION 7 R114 / R115 / R116 / R117 / R112
SECTION 7 7 smb / SMB-LOCK / SMC R114 / R115 / R116 / R117 / R112 Contents SMB Introduction... 7-4 to 7-5 Interface... 7-6 Characteristics... 7-7 to 7-8 Plugs... 7-8 to 7-9 Jacks...7-9 to 7-10 Bulkhead
SMB Connectors. Adaptors-50Ω. Plug to Plug. Jack to Jack. Plug to Jack. Bulkhead Jack to Jack
SMB Connectors Adaptors-50Ω Plug to Plug 1P-801-00 Jack to Jack 1P-802-00 Plug to Jack 1P-803-00 Bulkhead Jack to Jack 1P-804-18 Mini-SMB 75Ω Straight Plug 1P75-111-00 Cable group RG316 Straight PCB Jack
SECTION 12. N / Composite N / N 18 GHz R161 / R162 / R163
SECTION 12 12 N / Composite N / N 18 GHz R161 / R162 / R163 Contents Introduction... 12-4 to 12-5 N 50Ω and Composite N Interface... 12-6 Characteristics... 12-8 to 12-9 ECO N characteristics... 12-9
INTRODUCTION A WIDE STANDARD RANGE MANY FULL CRIMP MODELS LOW INTERMODULATION CONNECTORS
N INTROUCTION The new Radiall N series has been developed using the latest advances in connector design. These connectors are easy--to--use, highly reliable, innovative and are designed to meet the needs
SERIESN50, COAXIAL CONNECTORS
SERIESN50, COAXIAL CONNECTORS DESCRIPTION CONTENTS PAGE HUBER+SUHNER N connectors are available with 50 and 75 impedance. The frequency range extends to 18 GHz, depending on the connector and cable type.
TNC / TNC 18 GHz series R143 / R144
11 TNC / TNC 18 GHz series R143 / R144 CONTENT TNC Pages TNC Introduction... 11-4 Interface... 11-4 Characteristics... 11-6 TNC Ω Plugs... 11-8 to 11-9 Jacks... 11-9 to 11-11 Receptacles... 11-11 to 11-12
SECTION 14. DIN 1.0/2.3 / DIN 1.6/5.6 / Type 43 R118 / R120 / R129 / R214
SECTION 14 14 DIN 1.0/2.3 / DIN 1.6/5.6 / Type 43 R118 / R120 / R129 / R214 Contents DIN 1.0/2.3 Introduction... 14-4 Interface... 14-4 Characteristics Eco... 14-5 Plugs Eco... 14-6 Jacks Eco... 14-6
242, , FAX.
TEL. 886 2 8994 1601, FAX. 886 2 8994 1602 sales@rfconnector.com.tw, www.rfconnector.com.tw General Information SMA SMB Subminiature Connectors Screw Lock Subminiature Connectors Snap Lock 50 Ω 18 GHz
7/16 GENERAL. DC GHz GENERAL APPLICABLE STANDARDS APPLICATIONS
GENERAL 50 Ω C - 7.5 GHz GENERAL Standard coaxial connectors Screw--on coupling High power rating Excellent RF performance APPLICABLE STANARS IEC 169-4 IN 47223 22 190 APPLICATIONS Mobile communication
SMA - 50 Ohm Connectors
For Flexible Cable Straight Crimp Type Plug - Captivated Contact CABLE TYPE RG-178/U, 196 1.20 +.025 f (GHz) 0-12.4 GHz 142-0402-001 142-0402-006 RG-161/U, 174,188, 316 RG-188 DS, RG-316 DS RG-58/U, 141,
SMA 50 Ohm Connectors Alphabetical Index INCHES (MILLIMETERS) CUSTOMER DRAWINGS AVAILABLE ON REQUEST
SMA 50 Ohm Connectors Alphabetical Index SMA Connectors - 50 Ohm Bulkhead Mount... 20 Custom Feedthroughs... 48 Dummy Loads... 37 End Launch... 16 Field Replaceable... 28 Flexible Cable... 8 In-Series
SECTION 5 SWITCHING CONNECTORS/MOEBIUS MC-CARD/RP-MCX R199/R299 SIMPLIFICATION IS OUR INNOVATON. Visit for more information
SECTION 5 SWITCHING CONNECTORS/MOEBIUS MC-CARD/RP-MCX R199/R299 SIMPLIFICATION IS OUR INNOVATON Visit www.radiall.com for more information Contents Introduction... 5-4 to 5-5 MOEBIUS Characteristics...
Amphenol RF Interconnects BNC 31 Series Bayonet Lock RF Connector System
BNC 31 Series Bayonet Lock RF Connector System Materials Body/Finish /Nickel Centre MALE Centre FEMALE Phosphor Bronze Centre Finish Gold 30µ Insulator Delron/PBT Gasket Silicone Rubber Crimp s Annealed
SMA Description Applications Features
MCX SMA Description SMA connectors are adaptable to interconnection requirements of both systems and components.s - Corm offers a wide variety of cable connectors,receptacles, feed thrus, end launches,
Broadband performance with low reflection DC to 4 GHz provides low cost connector combined with high quality.
Amphenol RF 36 Connectors Description The name derives from SubMiniature B (the second subminiature design). Developed in the 1960 s, this sub miniature interface has snap-on coupling. Amphenol s connectors
SERIES SMB SUBMINIATURE CONNECTORS
SERIES SMB SUBMINIATURE CONNECTORS DESCRIPTION CONTENTS PAGE The HUBER+SUHNER subminiature connectors Series SMB, SMC, SMS have the same basic design. They only differ with regard to their coupling mechanism.
Amphenol RF. Mini-BNC Mini-BNC Connectors. Mini-BNC. Description. Features/Benefits. Applications
Amphenol RF 100 Connectors Description Amphenol RF introduces the new generation of quality BNC connectors for the telecommunication and broadband applications for higher connector densities while preserving
STANDARD COAXIAL CONNECTORS. Eco 7/16 series
STANDARD COAXIAL CONNECTORS Eco 7/16 series Eco 7/16 INTRODUCTION GENERAL Standard coaxial connectors Screw on coupling Compliant to CECC and IEC standards 50 Ω APPLICATIONS Broadcast RF components (filters,
N / Composite N / N 18 GHz series R161 / R162 / R163
12 N / Composite N / N 18 GHz series R161 / R162 / R163 CONTENTS N Pages Introduction... 12-4 to 12-5 N Ω and Composite N Interface... 12-6 Characteristics...12-8 to 12-9 Plugs... 12-12 to 12-14 Jacks...
MMS/MMT MMCX CONTENTS PAGE MMS/MMT
MMCX CONTENTS PAGE MMS/MMT Introduction... 4 General... 5 Characteristics MMS... 6 Characteristics MMT... 7 Connectors...8-9 Plugs... 10 Standard cable assemblies...11-12 Receptacles... 13 Adapters...
SMB Connectors. RF Coax Connectors. Product Facts
SMB Connectors Product Facts SMB offers snap-fit coupling for quick connect/disconnect Choice of Commercial or High Rel Connectors 50 and 75 Ω MIL-Type connectors available Straight plugs and jacks are
Amphenol RF MCX. MCX Connectors MCX. Description. Features/Benefits. Applications
Amphenol RF 20 Connectors Description connectors conform to the European CECC 22000 spec and were introduced in the 1980 s. While the uses identical inner contact and insulator dimensions as the SMB, the
Ø1,37 (.054) MIN Ø2,67 (.105) MAX Ø1,35 (.053) MAX Ø4,83 (.190) MAX 1,78 (.070) MAX 0,84 (.033) SEE NOTE # 2 1,91 (.075) MIN MIN CLOSED ENTRY CONTACT
SSMB / SSMC This range of 50 ohm microminiature radio frequency connectors is suitable for both military and commercial equipment operating at frequencies up to 4 GHz (SSMB) and 12.4 GHz (SSMC). They provide
RFX. Type N RG58, 141, 142 Straight Plug Type N Connectors» Cable Straight. Jack 50 Ohm Yes
Please note: Images are for reference only Amphenol Part Number: Description: Product Series: Product Type: Connector Body Style: Gender: Impedance: RoHS Compliant: 082-5376-RFX RG58, 141, 142 Straight
Amphenol RF- BNC Connector Series
Page 1 of 7 enter part number Products 7/16 1.0/2.3 1.6/5.6 AMC BNC / RP-BNC C FAKRA SMB FME HN MCX Mini-UHF Mini 75 Ohm SMB MMCX Precision (APC) QDS QMA QWS SC SlimLine BNC SMA / RP-SMA SMB SMC SMP TNC
Amphenol RF. MMCX Micro-Mate (MMCX) Connectors MMCX. Description. Features/Benefits. Applications
Amphenol RF 14 Micro-Mate () Connectors Description (also called MicroMate TM ), is a micro-miniature connector series with a snap-lock mechanism allowing for 360 degrees rotation enabling flexibility
kwiqmate Connectors Product Catalog Johnson
Product Catalog Johnson Emerson Connectivity Solutions, provider of kwiqmate branded Johnson product line of QMA connectors features a push-on style interface. Traditionally SMA plugs need to be configured
Amphenol RF UHF. UHF Connector Series UHF. Description. Features/Benefits. Applications
Amphenol RF 136 Connector Series Description Invented in the 1930 s by an Amphenol Engineer named E. Clark Quackenbush, coaxial connectors are general purpose units developed for use in low frequency systems
KCN KCN KCN KCN KCN KCN KCN KCN KCN KCN
series KCN4011200000 KCN4032200040 KCN4041100000 KCN4043110180 KCN4043140000 KCN4011200010 KCN4032200050 KCN4043100000 KCN4043110190 KCN4043140090 KCN4011200020 KCN4041200000 KCN4037100000 KCN4043110220
From dc to 10 GHz the. VSWR shall not exceed 1.3 &.04 (f) where f is the frequency in Gigahertz (GHz).
121 Series Coaxial Snap On & Screw On Types / 50 Ohm & 75 Ohm These 50 and 75 Ohm coaxial connectors are easily inserted into your printed circuit board using an insertion tool. Solder is eliminated and
RF & MW Connectors. 6 Where signal & Connectivity is needed, There is GigaLane
RF & MW Connectors - 2.4 mm Connectors - 2.92 mm Connectors - Hermetic Seal (0.012 Glass Bead) - SMP Connectors - BMA Connectors - High Performance End Lanch Connectors - High Performance SMA Connectors
RF COAXIAL PHASE SHIFTER SMA DC to 18 GHz DETAIL SPECIFICATION
1/ 35 Titre / Title RF COAXIAL PHASE SHIFTER SMA DC to 18 GHz DETAIL SPECIFICATION Rédigé par / Written by Responsabilité / Responsibility Date Signature S. POIZAT Space Project Manager 04/12/2015 Vérifié
242, , FAX.
TEL. 886 2 8994 1601, AX. 886 2 8994 1602 sales@rfconnector.com.tw, www.rfconnector.com.tw General Information Subminiature Connectors Subminiature Connectors Snap Lock 50 Ω 18 GHz 50 Ω 75 Ω 4 GHz 3 GHz
TNC Series. Interface Mating Dimensions. Coaxial Connectors
TNC connectors are designed with a Highly reliable threaded coupling to ensure additional protection against shocks and vibrations. They are dimensionally and electrically similar to the BNC series, and
ReversePolarity Series(SMA,BNC,TNC)
RP ReversePolarity Series(SMA,BNC,TNC) Description Reverse polarity BNC, TNC, N & SMA connectors (RP-BNC, RP-TNC, RP-SMA) are designed for uses in wireless applications where a non-standard interface has
Electrical dielectric withstanding voltage. sea level Vrms Vrms m Vrms Vrms
Applications Mechanical and electrical interface between on-board civil avionics equipments and racks Standards Arinc 600 Characteristics Mechanical material finish aluminum alodine 00 shells alloy to
Corning Gilbert Inc. Microwave Push-on Interconnects 1
Corning Gilbert Inc. Microwave Push-on Interconnects 1 GPO Specifications General Characteristics Impedance 50 ohms nominal Frequency range DC to 40 GHz Temperature range -65 C thru 165 C Electrical Characteristics
GPPO Interconnect Series Product Information
GPPO Interconnect Series Product Information A sub-miniature, push-on, high performance, microwave interconnect system. Developed in response to industry demand for increased package density, lower weight,
TECHNICAL DATA SHEET 1 / 4 MATERIALS
.. pn ao TECHNICAL DATA SHEET 1 / 4 STRAIGHT HDC CONNECTOR CC MALE CRIMP All dimensions are in mm. COMPONENTS MATERIALS PLATING (µm) BODY CENTER CONTACT OUTER CONTACT INSULATOR GASKET OTHERS PARTS BRONZE
EN2 SERIES SEALED CONNECTORS
FEATURES & BENEFITS Sealed to IP68, NEMA 250 (6P) (when mated) Available in standard or winged coupling ring Patented grommet and o-ring free design Solder/crimp and PC contact options APPLICATIONS Any
242, , FAX.
TEL. 886 2 8994 1601, AX. 886 2 8994 1602 sales@rfconnector.com.tw, www.rfconnector.com.tw General Information Subminiature Connectors Subminiature Connectors Snap Lock 50 Ω 18 GHz 50 Ω 75 Ω 4 GHz 3 GHz
PERFORMANCE SPECIFICATION SHEET CONNECTOR, PLUG, ELECTRICAL, TRIAXIAL, RADIO FREQUENCY (SERIES TRB, PIN CONTACT, CLASS 2)
INCH-POUND MIL-PRF-49142/3G 05 February 2016 SUPERSEDING MIL-PRF-49142/3F 18 April 2005 PERFORMANCE SPECIFICATION SHEET CONNECTOR, PLUG, ELECTRICAL, TRIAXIAL, RADIO FREQUENCY (SERIES TRB, PIN CONTACT,
PERFORMANCE SPECIFICATION SHEET
INCH-POUND 10 August 2016 SUPERSEDING 16 November 2011 PERFORMANCE SPECIFICATION SHEET CONNECTORS, RECEPTACLE, ELECTRICAL, COAXIAL, RADIO FREQUENCY, SERIES SMB (CABLED, PIN CONTACT, JAMNUT MOUNTED, REAR
RF COAXIAL CONNECTORS, BASED ON TYPE SMP. ESCC Detail Specification No. 3402/0xx
1/ 23 Titre / Title RF COAXIAL CONNECTORS, BASED ON TYPE SMP ESCC Detail Specification No. 3402/0xx Rédigé par / Written by Responsabilité / Responsibility Date Signature S. POIZAT Space Project Manager
BNC Connectors (50 ohm/75 ohm)
BNC Connectors (50 ohm/75 ohm) Product Facts Bayonet lock coupling for quick connect/disconnect Various connectors available in 50 and 75 ohm versions Fully intermateable with comparable BNC UG/U connectors
Date: April 27 th, 07. Titre / Title HIGH RELIABILITY RF COAXIAL CONNECTORS SMA TYPE, 50 OHMS (FEMALE CONTACT)
REF. : RADDETCONN003 2 / 1/ 18 Titre / Title HIGH RELIABILITY RF COAXIAL CONNECTORS SMA TYPE, 50 OHMS (FEMALE CONTACT) Rédigé par / Written by Responsabilité / Responsibility Date Signature S. POIZAT Space
Tru products are now under the Tru-Win brand from Winchester Interconnect.
TRU MEIA Series Tru-Win MEIA offers the latest innovation in high power connector design. The MEIA interface provides equivalent kw power handling compared to similar EIA connector line sizes but provides
Date: May 17 th, 16. Titre / Title HIGH RELIABILITY RF COAXIAL CONNECTORS SMP TYPE, 50 OHMS
1/ 20 Titre / Title HIGH RELIABILITY RF COAXIAL CONNECTORS SMP TYPE, 50 OHMS Rédigé par / Written by Responsabilité / Responsibility Date Signature S. POIZAT Space Project Manager 17/05/2016 Vérifié par
sealed mini usb connectors
QUICK CONNECT CABLE END MATES WITH PANEL MOUNT PANEL MOUNT MATES WITH CABLE END REAR VIEW - PC TAIL REAR VIEW - FEED-THRU TERMINATION REAR VIEW - SOLDER HOLES SPECIFICATIONS Mechanical Specifications Life:
Date: April 27 th, 04. Titre / Title HIGH RELIABILITY RF COAXIAL ADAPTORS AND CONNECTING PIECES SMA TYPE, 50 OHMS
1/ 21 Titre / Title HIGH RELIABILITY RF COAXIAL ADAPTORS AND CONNECTING PIECES SMA TYPE, 50 OHMS Rédigé par / Written by Responsabilité / Responsibility Date Signature S. POIZAT Space Project Manager 27/04/07
TNC Connectors. General Description. TNC Configurations. TNC Specifications* Plug Interface** Jack Interface**
TN onnectors General Description Delta TN connectors are compact, 50 Ω impedance connectors with 7 16-28 threaded coupling, similar in size to N connectors but with better electrical characteristics. They
2.4mm coaxial connectors for frequency test measurements
2.4mm coaxial connectors for frequency test measurements 2.4mm Series Functional diagram Straight plug H2.4-P-SS085 Plug side Attenuator PlugJack H2.4-AT (**)-PJ ** 0, 3, 6, 10, 20dB Features 1. Complies
Date: December 10 th, Titre / Title HIGH RELIABILITY RF COAXIAL CONNECTORS SMA 2.9 TYPE, 50 OHMS (FEMALE CONTACT)
REF. : RADDETCONN006 1/ 18 Titre / Title HIGH RELIABILITY RF COAXIAL CONNECTORS SMA 2.9 TYPE, 50 OHMS (FEMALE CONTACT) Rédigé par / Written by Responsabilité / Responsibility Date Signature S. POIZAT Space
SSMC Connectors. Microminiature, screw-on mating High performance to 12.4 GHz. General Description
SSMC Connectors Microminiature, screw-on mating High performance to 12.4 GHz General Description Delta SSMC connectors are microminiature, 50Ω impedance connectors with 6-40 threaded coupling. SSMC connectors
Times Microwave Systems Hermetically Sealed Assemblies
SCOPE This Specification details the Electrical, Mechanical and Environmental Characteristics of Times Microwave Systems MILTECH 480.48 Diameter Hermetically Sealed Coaxial Transmission Lines. This product
MIL-DTL-39030/3 SMA Terminations. Features & Benefits. Applications. M39030 /3-08 S or N
MIL-DTL-39030/3 SMA Terminations SV Microwave offers military SMA terminations that are 39030 approved. QPL-39030 parts are designed and made under DSCC qualifications in order to resist harsh environments
- UMP series : board to wire application
MMP INTRODUCTION RADIALL, the pioneer in SMT coaxial connectors with the MMS series, has become a world wide leader in this technology. Thanks to this SMT expertise, RADIALL now announces another breakthrough
MIL-C-17 Standard RF Coaxial Cable Low Loss & Ultra Low Loss RF Microwave Cable ANTENNA & TEST Cable up to 26.5 GHz
MIL-C-17 Standard RF Coaxial Cable Low Loss & Ultra Low Loss RF Microwave Cable ANTENNA & TEST Cable up to 26.5 GHz Low Loss Low Density PTFE Dielectric RF Microwave Coaxial Cable Silver Plated Copper
711 Series Single Way DB-1a
711 Series Single Way DB-1a Data Bus Interconnection System Data Bus Interconnection System designed for data transmission as defined by MIL-STD-1553B, STANAG 3838 and DEF STAN 00-18 (Part 2). This system
BNC Connectors. General Description. BNC Configurations. BNC Specifications* Plug Interface** Jack Interface**
N onnectors General Description Delta N connectors are compact, economical, 50Ω impedance connectors with two-stud bayonet coupling. They are best suited for use with cables in the range of.150" to.50"
N Male Connector Clamp/Solder Attachment for RG17, RG218, RG219
N Male Connector Clamp/Solder Attachment for RG17, RG218, RG219 RF Connectors Technical Data Sheet PE4433 Configuration N Male Connector MIL-STD-348 50 Ohms Features Silver Plated Contact Applications
Interface Mating Dimensions
connectors are subminiature units designed to provide high electrical performance for microwave applications up to 18GHz. Constructed with Brass or high quality stainless steel, connectors ensure excellent
MCX. Aliner Industries, Inc. No. 32, Lane 387, Min-an Rd., Sinjhuang City, Taipei County 24256, Taiwan
MCX Aliner Industries, Inc. No. 32, Lane 387, Min-an Rd., Sinjhuang City, Taipei County 24256, Taiwan Tel : +886-2-2205-5791 E-mail : sales@aliner.com.tw Fax : +886-2-2203-8052 / 2205-5628 http://www.aliner.com.tw
LGH High Voltage Connectors
Introduction Product Facts No exposed high voltage parts Space saving maximum performance from small size and weight Fast connect and disconnect Wide temperature range -67 F to +257 F [-55 C to +5 C],
SECTION TITLE PAGE. 1 Description of Connectors and Intended Applications 2. 2 Marking of Connector and/or Package 2. 3 Ratings 3
C0053 M80 & M83 SERIES RECTANGULAR CONNECTORS FEBRUARY 8 SECTION TITLE PAGE Description of Connectors and Intended Applications 2 2 Marking of Connector and/or Package 2 3 Ratings 3 Appendix Contact Orientations
JULY 2014 SECTION TITLE PAGE. 1 Description of Connectors and Intended Applications 2. 2 Marking of Connector and/or Package 2.
M80 & M83 SERIES RECTANGULAR CONNECTORS JULY 204 SECTION TITLE PAGE Description of Connectors and Intended Applications 2 2 Marking of Connector and/or Package 2 3 Ratings 3 Appendix Contact Orientations
SMA Self-Fixture End Launch Connectors
SMA Self-Fixture End Launch Connectors An ideal solution for design engineers who are obligated to cut manufacturing costs and complexity out of their circuit board system. For those microwave engineers
TIMES QUALIFIED MILTECH CABLE ASSEMBLIES
TIMES QUALIFIED MILTECH CABLE ASSEMBLIES Starting on page 5 MILTECH Qualified Cable Assemblies Manufactured to the requirements of MIL-C-87104 and MIL-T-81490, FAA FAR25 and DO-160 Fully vapor sealed for
SMA Self-Fixture End Launch Connectors
SMA Self-Fixture End Launch Connectors INTRODUCTION / APPLICATIONS Applications for these connectors include: An ideal solution for design engineers who are obligated to cut manufacturing costs and complexity
TNC Male Right Angle Connector Crimp/ Solder Attachment for RG174, RG316, RG188, inch, PE-B100, PE-C100, LMR-100
TNC Male Right Angle Connector Crimp/ Solder Attachment for RG174, RG316, RG188, 0100 inch, PE-B100, PE-C100, LMR-100 RF Connectors Technical Data Sheet PE4455 Configuration TNC Male Connector 50 Ohms
Electrical Components Catalog RF Connectors
Introduction Product Facts Designed and Manufactured to meet MI-C-39012 Requirements Wide Range of Connectors available in 50 and 75 Ohm Impedance The range offers connectors to suit from DC-11 GHz Operation
Board to Board Connector Board to Board Connector
Board to Board Connector Board to Board Connector GigaLane Board to Board connectors are especially developed for board-to-board and board-to-module RF interconnections. It is the perfect solution for
SMA Male Connector Crimp/Solder Attachment for RG58, RG303, RG141, PE-C195, PE-P195, LMR-195, inch
SMA Male Connector Crimp/Solder Attachment for RG58, RG303, RG141, PE-C195, PE-P195, LMR-195, 0195 inch RF Connectors Technical Data Sheet PE4215 Configuration SMA Male Connector MIL-STD-348A 50 Ohms Straight
7/16 DIN Male Connector Crimp/Solder Attachment for RG214, RG9, RG225, RG393
7/16 DIN Male Connector Crimp/Solder Attachment for RG214, RG9, RG225, RG393 RF Connectors Technical Data Sheet PE4571 Configuration 7/16 DIN Male Connector IEC 169-4 50 Ohms Straight Body Geometry Features
Technical Data Sheet STRAIGHT MALE RECEPTACLE FOR PCB SNAP TYPE - REEL OF 400
.. pn ao Technical Data Sheet PAGE 1/5 ISSUE 09-11-16E SERIES SMP-MAX PART NUMBER R222M00090 All dimensions are in mm. COMPONENTS MATERIALS PLATING ( m) Body BRASS NPGR Center contact BRASS NPGR Outer
Table of Contents. Corning Gilbert Inc. Microwave Push-on Interconnects 1
Table of Contents Corning Gilbert Inc. Microwave Push-on Interconnects 1 TABLE OF CONTENTS General Information II Who We Are III Custom Designs IV Reference Guide GPO Products 2 GPO Specifications 3 Blindmate
141 SMNB Model Series
HAND Coaxial TM Cable 50Ω DC to 12.5 GHz 141 SMNB Model Series The Big Deal N-Type (F) Bulkhead Connector to SMA (M) Hand Formable Tight Bend-Radius (8mm min.) Ideal for interconnect of assembled systems
RF COAXIAL CONNECTORS
RF COAXIAL CONNECTORS 17550 Gillette Avenue, Irvine, California 92614 www.sabritec.com Telephone (949) 250-1244 Fax (949) 250-1009 157 CoAXIAL CONNECTORS SCX Coaxial INTRODUCTION Sabritec offers a complete
QN Male Connector Crimp/Solder Attachment for RG55, RG141, RG142, RG223, RG400
QN Male Connector Crimp/Solder Attachment for RG55, RG141, RG142, RG223, RG400 RF Connectors Technical Data Sheet PE44978 Configuration QN Male Connector 50 Ohms Straight Body Geometry Features Max Operating
RF CABLE ASSEMBLY, TNC, VERY HIGH POWER, 50 OHMS, SEMI-RIGID AND FLEXIBLE CABLE, DC TO 8GHZ BASED ON TYPE TNC-VHP
Page 1 of 21 RF CABLE ASSEMBLY, TNC, VERY HIGH POWER, 50 OHMS, SEMI-RIGID AND FLEXIBLE CABLE, DC TO 8GHZ BASED ON TYPE TNC-VHP ESCC Detail Specification Issue 1 March 2017 Document Custodian: European
7/16 DIN Male Right Angle Connector Clamp/Solder Attachment for RG213, RG214, RG8, RG9, RG225, RG393, RG215
7/16 DIN Male Right Angle Connector Clamp/Solder Attachment RF Connectors Technical Data Sheet PE44280 Configuration 7/16 DIN Male Connector MIL-C-39012 50 Ohms Right Angle Body Geometry Features Silver
EACON. Field mountable microwave cable. INEXIM Sp. z o.o. Edition Bezpośredni importer i dystrybutor
EACON Field mountable microwave cable Edition 2012 Bezpośredni importer i dystrybutor INEXIM Sp. z o.o. www.inexim.pl Easy connected EACON - the field mountable cable assembly 4 EACON 4C 6 Suitable to
RG142-TNMNM-3M. Jumper Assembly Sample Label. Product Classification. General Specifications. Return Loss/VSWR. Regulatory Compliance/Certifications
RG142-TNMNM-3M Product Classification Product Series Product Type RG142 CNT Jumper with interface types and, 3 m RG142 Braided cable assembly General Specifications Body Style, Connector A Body Style,
BNC 75 OHM CONNECTOR PRODUCTS
BNC 75 OHM CONNECTOR PRODUCTS ADC's BNC Connectors are the most reliable and universally accepted method of terminating coaxial cable in the market today. Outstanding electrical performance (up to 3 GHz)
The GPO male interface is compliant to MIL-STD-348, and it is in accordance with MIL-PRF-39012a and DESC 94007/94008.
GPO, GPPO and G3PO Application Notes Corning Gilbert s push-on connector products allow users flexibility in modular and board layout (in high density situations), frequency bandwidths from DC to 100 GHz
CONNECTORS, ELECTRICAL, CIRCULAR, TRIPLE-START SELF-LOCKING COUPLING, SCOOP-PROOF, REMOVABLE CRIMP CONTACTS BASED ON MIL-C SERIES III
Page 1 of 24 CONNECTORS, ELECTRICAL, CIRCULAR, TRIPLE-START SELF-LOCKING COUPLING, SCOOP-PROOF, REMOVABLE CRIMP CONTACTS BASED ON MIL-C-38999 SERIES III ESCC Detail Specification Issue 6 October 2013 Document
DETAIL SPECIFICATION SHEET
DETAIL SPECIFICATION SHEET INCH-POUND 21 April 2015 SUPERSEDING 31 May 2005 CONNECTOR, RECEPTACLES, ELECTRICAL, COAXIAL, RADIO FREQUENCY, STRIP OR MICROSTRIP TRANSMISSION LINE, SERIES SMA (SOCKET CONTACT,
Series 791 Connectors
Pin and Socket s for Series 79 Connectors Crimp s Size 23 Crimp s Operating temperature: -65 to +150 C Current rating: 5A Crimp Tensile Strength Wire Size Axial Load (lbs.) 22 12 24 8 26 5 28 3 30 1.5
C400-TMTM-30-X. Jumper Assembly Sample Label. Product Classification. General Specifications. Electrical Specifications
C400-TMTM-30-X Product Classification Brand Product Series Product Type CNT-400-FR CNT Jumper with interface types TNC Male and TNC Male, 9.14 m CNT CNT-400 Braided cable assembly General Specifications
D Subminiature Combo D
Cable ( 8) Loose Contacts Coaxial 75 Ohm Stamped Crimp/Crimp Recommended Wire Trim Dimensions Kit (ody, Ferrule, Center Contact) Stamped Crimp/Crimp Kit Kit 30 in. Kit 50 in. RG Cable Number D130322-2
086 Model Series. 50Ω DC to 18 GHz. The Big Deal
HAND Coaxial TM Cable 50Ω DC to 18 GHz 086 Model Series The Big Deal Hand Formable Tight Bend Radius Excellent Return Loss and Insertion Loss Ideal for interconnect of assembled systems CASE STYLE: KP1505-XX
TRUtest Specifications. Electrical. Mechanical. Environmental. Requirement. Detail. 1.35:1 maximum. 0.4 db/ft GHz
TRUtest Series TRUtest Series cable assemblies combine MIL-standard test-grade interfaces with flexible and durable cable construction to provide repeatable, reliable performance and long service life.
PRODUCT SPECIFICATION. This specification defines the detailed requirements for the Minitek Pwr3.0 wire to wire and wire to board connectors.
1.0 SCOPE 1 of 8 E This specification defines the detailed requirements for the Minitek Pwr3.0 wire to wire and wire to board connectors. 2.0 APPLICABLE DOCUMENTS The following documents, of the latest
C400-NMTM-1M. Jumper Assembly Sample Label. Product Classification. General Specifications. Return Loss/VSWR
C400-NMTM-1M Product Classification Brand Product Series Product Type CNT-400 CNT Jumper with interface types N Male and TNC Male, 1m CNT CNT-400 Braided cable assembly General Specifications Body Style,
RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].
![RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].](/thumbs/90/101629325.jpg "RF Connectors Technical Data Sheet. Gold over Nickel Plated Beryllium Copper Contact. Size in [11.81 mm] . Weight lbs [3.18 g].")
RP SMA Male Connector Solder Attachment for PE-SR402AL, PE-SR402FL, PE-SR402FLJ, PE- SR402TN, RG402, Gold Plated Brass Body RF Connectors Technical Data Sheet PE44724 Configuration SMA Male Reverse Polarity
ATBTK-MF-4G. Product Classification. Mechanical Specifications. Dimensions. Regulatory Compliance/Certifications.
ATBTK-MF-4G Bias Tee Kit, AISG Compatible 698-2700 MHz Product Classification Product Type RET bias tee Mechanical Specifications Antenna Interface 7-16 DIN Female BTS Interface 7-16 DIN Male Dimensions
RP TNC Male Connector Crimp/Solder Attachment for PE-C240, RG8X, inch, LMR-240, LMR-240-DB, LMR-240-UF, B7808A
RP TNC Male Connector Crimp/Solder Attachment for PE-C240, RG8X, 0240 inch, LMR-240, LMR-240-DB, LMR-240-UF, B7808A RF Connectors Technical Data Sheet PE44670 Configuration TNC Male Reverse Polarity Connector
CSP-03G-003 High-Frequency Coaxial Test & Measurement Probe Model Number: CSP-03G-003, Replacement Probe: SPL-03G-043, SPL-03B-121 Target Connector: CPT-03-50-2 Applications: Designed for use in interconnect
Optimize Your RF/MW Coaxial Connections. Dave McReynolds Director of Engineering RF Industries
RF Optimize Your RF/MW Coaxial Connections Dave McReynolds Director of Engineering RF Industries /microwave connectors are small and often overlooked, but they serve as gateways for many electronic devices
... A Vital Part of Connection World CMPTER. 1.85mm Connector Applycation Receptacles With Accepts Pin
... A Vital Part of Connection World 1.85mm Connector Applycation Receptacles With Accepts Pin COPYRIGHT ELECTRONICS 2014 1.85mm Precision Connectors DESCRIPTION The 1.85mm connector are 50 ohm precision