MT4 Relay. 4 pole telecom/signal relay Through Hole Type (THT) Non-polarized. non-latching 1 coil. Features. Typical applications
|
|
|
- Harold Cain
- 6 years ago
- Views:
Transcription
1 4 pole telecom/signal relay Through Hole Type (THT) Non-polarized. non-latching 1 coil Features Telecom/signal relay (dry circuit, test access, ringing) 20 x 14.8 mm, x inch Switching current 1.25 A 4 changeover contacts (4 form C / 4PDT) Bifurcated contacts Meets Bellcore GR 1089, FCC Part 68 and ITU-T K V Typical applications Communications equipment Linecard application analog, ISDN, xdsl PABX Voice over IP Office and business equipment Measurement and control equipment Consumer electronics Set top boxes, HiFi Medical equipment European Directive conformance: MT4 relay product conformance according to: - Directive 2000/53/EC: ELV (End of Life of Vehicles) - Directive 2002/95/EC: ROHS (Restrictions of the use of certain hazardous substances in electrical and electronic equipment) Compliance is evidenced by written declaration from all raw material suppliers. Tyco Electronics AXICOM only has responsibility for the proper processing of these materials. Confirmation is valid for date codes 0501 UL 508 File No. E Page 2 (9) Rev. C
2 THT Version Dimension THT mm inch Mounting hole layout View onto the component side of the PCB (top view) L 20.0 ± ± W 14.8 ± ± H / / T 3.1± T1 N/A N/A T ± ± Tw S Basic grid 2.54 mm Terminal assignment Relay - top view non-latching 1 coil release condition Page 3 (9) Rev. C
3 Coil Data (values at 23 C) Ordering Information Nominal Operate/set voltage range Release/ Coil Coil Relay Tyco part voltage reset voltage power Resistance code number Unom Minimum Minimum Maximum voltage U min voltage U max Vdc Vdc Vdc Vdc mw Ω / ± 10 % non-latching 1 coil C C C C C C C Coil operating range Ambient Temperature [ C] Coil Voltage [U/Unom] Unom. nominal coil voltage 300 mw coil Umax. at 0 A Umax. at 2 x 1.25 A Umax. at 4 x 1.25 A U nom U max. U op. min. U rel. min. Nominal coil voltage Upper limit of the operative range of the coil voltage (limiting voltage) when coils are continously energized Lower limit of the operative range of the coil voltage (reliable operate voltage) Lower limit of the operative range of the coil voltage (reliable release voltage) Uop. min. Urel. min Ambient Temperature [ C] Page 4 (9) Rev. C
4 Contact Data Number of contacts and type Contact assembly Contact material Limiting continuous current at max. ambient temperature Maximum switching current Maximum swichting voltage Maximum switching capacity Thermoelectric potential Initial contact resistance / measuring condition: 10 ma / 20 mv Electrical endurance Mechanical endurance UL contact ratings Contact application 0 (< 30 mv/< 10 ma) Cable load open end Resistive load 150 V / 0.2 A - 30 W 24 V / 1.25 A - 30 W 4 changeover contacts Bifurcated contacts Silver-nickel, gold-covered 1.25 A 1.25 A 150 Vdc 150 Vac 30 W, 62.5 VA < 10 mv < 70 mw min. 1 x 10 7 operations min. 5 x 10 6 operations min. 2.0 x 10 5 operations min. 2.0 x 10 5 operations typ operations 24 Vdc / 1.25 A 125 Vac / 0.4 A Max. DC load breaking capacity Max. DC load breaking capacity DC Voltage [Vdc] DC current [A] Insulation Insulation resistance at 500 Vdc Dielectric test voltage (1 min) > 10 9 W 1800 Vrms 750 Vrms 750 Vrms Surge voltage resistance according to Bellcore TR-NWT (2 / 10 ms) according to FCC 68 (10 / 160 ms) and IEC (10 / 700 ms) 2500 V 2500 V Page 5 (9) Rev. C
5 High Frequency Data Capacitance max. 4 pf max. 2 pf max. 2 pf RF Characteristics Isolation at 100 / 900 MHz Insertion loss at 100 / 900 MHz V.S.W.R. at 100 / 900 MHz db / db db / db 1.03 / 1.31 General data Operate time at U nom typ. / max. Release time without diode in parallel (non-latching), typ. / max. Release time with diode in parallel (non-latching), typ. / max. Bounce time at closing contact, typ. / max. Maximum switching rate without load Ambient temperature Thermal resistance Maximum permissible coil temperature Vibration resistance (function) Shock resistance, half sinus, 11 ms Degree of protection Needle flame test Mounting position Processing information Weight (mass) Terminal surface Resistance to soldering heat 4 ms / 6 ms 1 ms / 3 ms 4 ms / 6 ms 1 ms / 5 ms 50 operations/s -55 C C < 100 K/W 115 C 10 G 10 to 500 Hz 10 G (function) 100 G (damage) immersion cleanable, IP 67 application time 10 s, any Ultrasonic cleaning is not recommended max. 7 g SnCu C / 10 s All data refers to 23 C unless otherwise specified. Page 6 (9) Rev. C
6 Packing Tube for THT version - 25 relays per tube, 500 relays per box Page 7 (9) Rev. C
MT4 Relay. The Best Relaytion
The Best Relaytion 4 pole telecom/signal relay Through Hole Type (THT) Non-polarized. non-latching 1 coil Features Telecom/signal relay (dry circuit, test access, ringing) 20 x 14.8 mm, 0.795 x 0.582 inch
AXICOM Telecom-, Signal and RF Relays. FX2 Relay Nov. 07 Rev. E ECOC: JM10
108-98003 Nov. 07 Rev. E ECOC: JM10 Disclaimer While Tyco Electronics has made every reasonable effort to ensure the accuracy of the information in this datasheet, Tyco Electronics does not guarantee that
AXICOM Telecom-, Signal and RF Relays. D2n V23105 Relay Nov. 07 Rev A ECOC: JM10
108-98007 Nov. 07 Rev A ECOC: JM10 Disclaimer While Tyco Electronics has made every reasonable effort to ensure the accuracy of the information in this datasheet, Tyco Electronics does not guarantee that
IM Relay Sept 06 Rev. F ECOC: JM10
108-98001 Sept 06 Rev. F ECOC: JM10 Index UL 508 File No. E 111441 UL 60950 IEC/EN60950 IEC Ref. Cert. No. 3270 Dimensions 4 Operating Range 5 Data and Ordering Information 6 Contact Data 10 Insulation
AXICOM Telecom-, Signal and RF Relays. HF3 Relay Aug. 08 Rev. E ECOC: JM10
108-98000 Aug. 08 Rev. E ECOC: JM10 Disclaimer While Tyco Electronics has made every reasonable effort to ensure the accuracy of the information in this datasheet, Tyco Electronics does not guarantee that
W11 Relay. The Best Relaytion
The Best Relaytion 1 pole PCB relay, non-polarized, Through Hole Type (THT) Relay types: Non-latching, 1 coil Terminal assignments symmetrical or assymetrical 5- or 6-pin version Features Multi purpose
Relay Types. Reed V23100-V4 Relay. Typical applications. Features. DIP version (flat) DIP version (high) SIL version.
1 and 2 pole relays non-polarized, non-latching ROHS compliant (Directive 2002/95/EC) as per product date code 0501. Features Direct coil control with TTL-signals possible Highly reliable switching High
RF Signal Relays AXICOM. HF3 Relay
HF3 Relay n Y-Design n Frequency range DC to 3GHz n Impedance 50Ω or 75Ω n Small dimensions (14.6x7.2x10mm) n 1 form C contact (1 changeover contact) n Immersion cleanable n Low power consumption ( 140mW)
onlinecomponents.com IM Series Signal Relays
IM Series Signal Relays IM Relay Disclaimer While Tyco Electronics and its affiliates referenced herein have made every reasonable effort to ensure the accuracy of the information contained in this catalog,
RF Signal Relays AXICOM. HF3 S Relay
n Y-Design n range DC to n Impedance 5 n Small dimensions (15x7.6x1.6mm) n 1 form C contact (1 changeover contact) n Immersion cleanable n Low power consumption ( 14mW) Typical applications Cable modems
PCB relay for DC voltage, polarized, monostable or bistable
V23042 PCB relay for DC voltage, polarized, monostable or bistable Features Universally applicable in the most varied circuit functions in the field of telecommunications and small signal technology Versatile
The Best Relaytion. Cradle Relay W Rev. B EC-JM ECOC: JM10 1. Aug. 04
The Best Relaytion Cradle Relay W 08-9803 Rev. B EC-JM00-0009-03 ECOC: JM0. Aug. 0 Hand solder and plug-in relay, for AC operation, non-polarized, non-latching Features highly reliable great variety of
The Best Relaytion. Cradle Relay N Rev. B EC-JM ECOC: JM10 1. Aug. 04
The Best Relaytion Cradle Relay N 108-98012 Rev. B EC-JM00-0009-03 ECOC: JM10 1. Aug. 04 PCB, hand solder or plug-in relays, for DC operation, non-polarized, non-latching Features Multi purpose relay highly
HF3 Relay (Preliminary)
Relay (Preliminary) 1 pole high frequency relay, polarized Through Hole Type (THT) or Surface Mount Technology (SMT) Relay types: non latching latching 1 coil latching 2 coils Features - Frequency range
RF Signal Relays AXICOM. HF3 S Relay
n Y-Design n range DC to n Impedance n Small dimensions (x7.6x.6mm) n form C contact ( changeover contact) n Immersion cleanable n Low power consumption ( 4mW) Typical applications Cable modems and linecards
The Best Relaytion. Cradle Relay S Rev. B EC-JM ECOC: JM10 1. Aug. 04
The Best Relaytion Cradle Relay S 108-98014 Rev. B EC-JM00-0009-03 ECOC: JM10 1. Aug. 04 Hand solder and plug-in relay, for DC operation, non-polarized, non-latching Features Stronger magnet system and
Signal Relays AXICOM. FT2/FU2 Relay
XIOM FT/FU Relay n Telecom/signal relay (dry circuit, test access, ringing) n Slim line x. (.9x.9 ) n Switching current n form bifurcated contacts ( O) n High sensitive V and V coil versions n Meets Telcordia
Signal Relays AXICOM. IM Relay
Signal s IM n Slim line 0x6mm, low prile 5.65mm and min. board-space 60mm n Switching current /5A, switching power 60/6.5VA and switching voltage 0VDC/50VAC n Low coil power consumption, 40m standard,
Miniature Power Relay MSR
V23061 PCB relay for DC voltage, neutral, monostable Features Used as a switching element for electrical separation between low-power control circuits and power load circuits With 8 mm clearance and creepage
Signal Relays AXICOM. P2 Relay V Coil Data
XIOM P Relay V9 n Standard telecom relay (ringing and test access) n Slim line x. (.9x.9 ) n Max. switching current n form bifurcated contacts ( changeover contacts, O) n Iersion cleanable n High sensitivity
2-POLES 2A (SLIM PROFILE SIGNAL RELAY) FTR-B4 Series
maluska elektronik ULTRA MINIATURE -POLES A (SLIM PROFILE SIGNAL RELAY) FTR-B Series RoHS compliant Features DPDT A Ihr Partner für Kontakt-Bauelemente Ultra miniature slim type relay for surface mounting
Signal Relays AXICOM. P2 Relay V Coil Data
XIOM P Relay V9 n Standard telecom relay (ringing and test access) n Slim line x. (.9x.9 ) n Max. switching current n form bifurcated contacts ( changeover contacts, O) n Iersion cleanable n High sensitivity
DISCONTINUED (2002) 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR12 SERIES MINIATURE RELAY FEATURES ORDERING INFORMATION
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR12 SERIES FEATURES Super miniature size: 0.2 inch 0.1 inch grid, 12 pin DIP Up to 50% less volume and board area than previous generation telecom
PRODUCT DATASHEET. is brought to you by. SOS electronic distribution of electronic components
PRODUCT DATASHEET is brought to you by SOS electronic distribution of electronic components Click to view availability, pricing and lifecycle information. Visit https://www.soselectronic.com/ Datasheet
NA SERIES. 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) MINIATURE RELAY. RoHS Compliant FEATURES ORDERING INFORMATION SAFETY STANDARD AND FILE NUMBERS
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) RoHS Compliant FEATURES Slim type relay for high density mounting Conforms to Bellcore specification and FCC Part 68 Dielectric strength 1,500 VAC
ULTRA LOW PROFILE 2 A POLARIZED RELAY. mm inch. Initial breakdown voltage
TESTING ULTRA LOW PROFILE POLARIZED RELAY RELAYS 9...7 mm inch FEATURES Low profile mm.7 inch height High contact capacity: Surge withstand between contact and coil:, V (Telcordia) RoHS Directive compatibility
Distributed by: www.jameco.com 1-8-81-44 The content and copyrights of the attached material are the property of its owner. SLIM POLARIZED RELAY TN RELAYS.551. 9.8.86 FEATURES Small header area makes higher
New pin layout (LT type) added. Best seller with broad lineup and AC 2000 V breakdown voltage.
Compliance with RoHS Directive FEATURES. 2, V breakdown between contact and coil The body block construction of the coil that is sealed at formation offers a high breakdown of 2, V between contact and
FTR-B4 Series ULTRA MINIATURE RELAY SLIM SIGNAL RELAY. RoHS Compliant FEATURES ORDERING INFORMATION
ULTRA MINIATURE RELAY SLIM SIGNAL RELAY Series FEATURES Ultra miniature slim type relay for surface mounting Height: 9. mm maximum (THT) mm maximum (SMT) Weight: Approximately. g UL/CSA recognized Conforms
MAGNETIC-LATCHING DC-8 GHz TO-5 RELAYS 4PST
MagneticLatching Electromechanical Relay MAGNETICLATCHING DC8 GHz TO5 RELAYS PST SERIES SGRF SGRFD RELAY TYPE PST RF Relay PST RF Relay with internal diodes for coil transient suppression DESCRIPTION The
PCB Relay. Contact form Terminal Single-side stable Single-winding latching Double-winding latching
PCB Relay Subminiature, Sensitive SPDT Signal Switching Relay High sensitivity: 98-mW pickup coil power. Impulse withstand voltage meets FCC Part 68 requirements. Fully sealed construction. Unique moving
MINIATURE RELAY 2 POLES, 2A HIGH INSULATION/WIDE GAP FTR-C1 Series
MINIATURE RELAY 2 POLES, 2A HIGH INSULATION/WIDE GAP FTR-C1 Series RoHS compliant Features 2 Poles, 2 form C Contact gap: more than 0.6mm High surge voltage: 2,00V between open contacts,000v between coil
Power PCB Relay. To Order: Select the part number and add the desired coil voltage rating (e.g., G6B-1114-US-DC6).
Power PCB Relay Subminiature 20 L x 9.90 W x 9.90 H mm (0.79 L x 0.39 W x 0.39 H in) Low power consumption (200 mw) Sealed construction permits automatic soldering and cleaning of the PC board High-capacity
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 16 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 16 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY Series GRF121 SERIES GRF121 RELAY TYPE RF Magnetic-Latching, SPDT, Surface Mount Relay DESCRIPTION The ultraminiature
HIGH REPEATABILITY, DC-8 GHz/20Gbps TO-5 RELAYS, DPDT
HIGH REPEATABILITY, DC-8 GHz/Gbps TO-5 RELAYS, DPDT SERIES RELAY TYPE RF3 RF33 Repeatable, RF relay Low Power Operating Coil, RF relay DESCRIPTION The ultra miniature RF3 is designed to improve upon the
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ, 20 Gbps MAGNETIC-LATCHING RF RELAY
HIGH REPEATABILITY SPDT, BROADBAND 12 GHZ, 20 Gbps MAGNETIC-LATCHING RF RELAY SERIES RF121 RF121R RELAY TYPE RF Magnetic-Latching, SPDT, Common Coil Negative, Through-Hole Relay RF Magnetic-Latching, SPDT,
3. Contact Form A: SPST-NO
0 A Compact and high power latching relay High power switching: 0 A, 6 VAC Compact size: mm mm mm Low temperature-rise High overcurrent capability, conforming to IEC6055- UC RoHS Compliant Model Number
LOW-PROFILE SURFACE-MOUNT RELAY. Characteristics. Initial breakdown voltage. Initial surge voltage. Temperature rise* 2 (at 20 C) Max.
TESTING LOW-PROFILE SURFACE-MOUNT RELAY RELAYS 5.6. mm inch FEATURES Low-profile: 6 mm.36 inch in height comforming to EIA standards (Tape height: max. 6.5 mm.56 inch ) Tape and reel package is available
RU Series Universal Relays
Full featured universal miniature relays Designed with environment taken into consideration Two terminal styles: plug-in and PCB mount Non-polarized LED indicator available on plug-in relays No internal
Classification Contact form Contact type Contact material Enclosure Rating Model Standard DPDT Bifurcated crossbar Ag (Au alloy) Fully sealed G5V-2
Miniature Relay for Signal Circuits ROHS compliant. Wide switching power of 10 µa to 2 A. High dielectric strength coil-contacts:1,000 VAC; open contacts: 750 VAC. Conforms to FCC Part 68 requirements.
PRODUCT DATASHEET. is brought to you by. SOS electronic distribution of electronic components
PRODUCT DATASHEET is brought to you by SOS electronic distribution of electronic components Click to view availability, pricing and lifecycle information. Visit https://www.soselectronic.com/ Datasheet
SY SERIES 1 POLE 1 A (FOR SIGNAL SWITCHING) MINIATURE RELAY SY SERIES. RoHS compliant
MINIATURE RELAY 1 POLE 1 A (FOR SIGNAL SWITCHING) SY SERIES RoHS compliant FEATURES Very small size and light weight UL, CSA recognized Conforms to FCC rules and regulations part 68 Dielectric strength
LoopBack Relay. LB363 Series. With Built-in AC Bypass Capacitors. LoopBack Relay, Sensitive Coil, thru-hole with AC Bypass Capacitors
LB363 Series With Built-in AC Bypass Capacitors SERIES DESIGNATION LB363 RELAY TYPE, Sensitive Coil, thru-hole with AC Bypass Capacitors DESCRIPTION The LoopBack Series relay combines two DPDT electromechanical
HIGH REPEATABILITY, TO-5 RELAYS DPDT
HIGH REPEATABILITY, TO-5 RELAYS DPDT SERIES RELAY TYPE RF7 RF7 Repeatable, RF relay Sensitive, repeatable, RF relay DESCRIPTION The ultraminiature RF7 and RF7 relays are designed to provide improved RF
ultra MINIature 2-POLes 2a (LOW PrOFILe signal relay) Ftr-B3 series rohs compliant Features
ULTRA MINIATURE -POLES A (LOW PROFILE SIGNAL RELAY) FTR-B3 SERIES RoHS compliant Features DPDT C Ultra miniature low profile relay with high heat resistant material Height: 5.45mm, Weight:.85g, Mounting
To be Discontinued FBR46 SERIES. MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR46 SERIES RoHS compliant FEATURES Miniature size About 50% smaller in volume compared with the FBR240 series used mainly in communication equipment.
4 mm height! 2 A high capacity 1 Form C type ultra thin, super miniature relay
4 mm height! A high capacity Form C type ultra thin, super miniature relay TK RELAYS TK RoHS compliant FEATURES. Compact and flat type.6(l) 9.(W) 4.(H).47(L).34(W).7(H). High contact capacity: A 3. Outstanding
DEVICES SRC. 1" x 0.1" GRID RELAYS HRB MMRB DESCRIPTION APPLICATIONS FEATURES. RATINGS 25 o C)
" x 0." GRID RELAYS DESCRIPTION The " x 0." grid relay series is a general purpose series that is pin-for-pin compatible with most competitor relays. Some configurations of this relay series are capable
Surface-mounting Relay
Surface-mounting Relay Extremely Thin SPST-NO Flat Relay, One of the Thinnest Relays in the World Dimensions of 7.(W).6(L) 4.2 mm(h) (SMD) or 3.8 mm(h) (TH) represent a reduction of approximately 2% in
4 mm height! 2 A high capacity 1 Form C type ultra thin, super miniature relay
4 mm height! A high capacity Form C type ultra thin, super miniature relay TK RELAYS TK FEATURES. Compact and flat type.6(l) 9.(W) 4.(H).47(L).4(W).7(H). High contact capacity: A. Outstanding surge resistance
Contact Ag + Au-clad AgPd + Au-clad. General purpose DPDT G6AU-274P-ST-US G6AU-234P-ST-US 4PDT G6AU-474P-ST-US G6AU-434P-ST-US
Fully sealed Relay with High Impulse Dielectric for Use in Telecommunications Equipment ROHS compliant. High sensitivity can be driven by digital circuits. Horizontal design allows use in 2 inch PCB racks.
MAGNETIC-LATCHING DPDT HALF-SIZE CRYSTAL CAN HIGH POWER RF RELAY DC-3 GHZ
MAGNETIC-LATCHING DPDT HALF-SIZE CRYSTAL CAN HIGH POWER RF RELAY DC-3 GHZ SERIES RELAY TYPE Commercial, DPDT, High Power, Half-Size Crystal Can Relay Commercial, DPDT, High Power, Half-Size Crystal Can
Low profile safety relay with forcibly guided double contacts FEATURES. Relay height, 14.5mm. 4a2b
Low profile safety relay with forcibly guided double contacts SFN4D RELAY 3.3 33.0 FEATURES Relay complies with EN 020, Type B. Polarized magnet system with snap action function Tolerance ±0.3 mm Weight
SPST-NO SPDT DPST-NO DPDT
PCB Relay A Power Relay with Various Models High-sensitivity ( mw) and High-capacity ( A) Models available. Low profile:.7 mm max. in height Conforms to VDE (EN0-), UL and CSA.. Meets EN0- requirements
LOW-PROFILE SURFACE-MOUNT RELAY
TESTING LOW-PROFILE SURFACE-MOUNT RELAY TQ SMD RELAYS.6. RoHS Directive compatibility information http://www.nais-e.com/ FEATURES Low-profile: 6 mm.36 inch (Tape height: max. 6. mm.6 inch) Tape and reel
PCB Relays Twin Relays
Features Smallest automotive PCB relay in its class: Minimum PCB area required: 7mm 2 Dimensions: L x H x W (mm).4 x 14.0 x 10.2 Minimal height: 14.0 mm Minimal weight First automotive relay using overmolding
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 18 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY
SURFACE MOUNT HIGH REPEATABILITY SPDT, BROADBAND 18 GHZ 40GBPS MAGNETIC-LATCHING RF RELAY Series GRF121/GRF121R SERIES GRF121 GRF121R RELAY TYPE RF Magnetic-Latching, SPDT, Common Coil Negative, Surface
MINIATURE POWER RELAY IN DS RELAY SERIES FEATURES resistance ORDERING INFORMATION. Ex. DSP 1 L DC12V R
MINIATURE POWER RELAY IN DS RELAY SERIES DSP- RELAYS DSPa DSP SPECIFICATIONS.. DSPa Coil (polarized) (at C F) Minimum mw power coil latching mw mw power coil latching mw.... Contact Arrangement a ab a
8 A MINIATURE POWER RELAY IN DS RELAY SERIES
DSP A MINIATURE POWER RELAY IN DS RELAY SERIES DSP RELAYS DSPa.. DSPa.. DSP.. RoHS Directive compatibility information http://www.nais-e.com/ FEATURES Power types added to DS relay series High switching
MINIATURE RELAY 1 POLE 1 to 2 A (FOR SIGNAL SWITCHING) FBR211 SERIES
MINIATURE RELAY POLE to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES 2 A maximum carrying current Capable of 2 A maximum continuous carrying current in the contact Superior reliability gold-overlay
8 A MINIATURE POWER RELAY IN DS RELAY SERIES FEATURES
A MINIATURE POWER RELAY IN DS RELAY SERIES DSP RELAYS FEATURES DSPa.. DSPa DSP.... Power types added to DS relay series High switching capacity: a: A V AC / ab, a: A V AC High sensitivity: mw pick-up power
CP RELAYS POWER TYPE. TYPICAL APPLICATIONS Defoggers, Ignitions, Heaters, Accessories, Powered windows, etc. ORDERING INFORMATION TYPES
High Carrying Current Type Miniature Low Profile Automotive Relay CP RELAYS POWER TYPE Sealed 13.1 14.1 9..374 FEATURES Maximum carrying current of 3 A (4 mw type, 1 V applied)
PCB Relay. --- G2R-1-SN --- G2R-2-SN LED indicator with test
PCB Relay A Power Relay for a Variety of Purposes with Various Models Conforms to VDE0 (VDE approval: C0 insulation grade), UL08, CSA., SEV, SEMKO. Meets VDE0700 requirements for household products according
CUP SERIES CP CLARE 399. Clare Universal Package DESCRIPTION 25 C FEATURES APPLICATIONS APPROVALS ORDERING INFORMATION
DESCRIPTION The Series has become a standard in the European relay market due to its versatile switch and schematic options. The staggered pin layout gives more space and allows for higher isolation from
DIP 14 SERIES REED RELAYS
DIP 4 SERIES REED RELAYS MSS MSS7 DSS7 PRME MVS MVS7 DESCRIPTION CP Clare s epoxy molded DIP 4 Series offers a variety of contacts and schematics to meet the needs of a wide range of applications. It features
LOW PROFILE 2 FORM C RELAY TQ RELAYS Ð Ð.008. mm inch. M.B.B.type. Initial breakdown voltage 1 A 30 V DC. 200 mw.
LOW PROFILE FORM C RELA RELAS 9.3 6.7.. Ð Ð.8. 9.3. Ð Ð.8 mm inch FEATURES High sensitivity: Form C: power consumption (single side stable type) Form C: power consumption (single side stable type) Surge
HIGH INSULATION RELAYS (Conforming to the supplementary insulation class of EN Standards (EN41003))
TESTING HIGH INSULATI RELAYS (Conforming to the supplementary insulation class of EN Standards (EN)) TX-D RELAYS.9.9 8...9.9 8.. FEATURES Approved to the supplementary insulation class in the EN standards
CENTIGRID ESTABLISHED RELIABILITY RELAYS
SERIES DESIGNATION CENTIGRID ESTABLISHED RELIABILITY RELAYS SENSITIVE DPDT 134 DPDT basic relay 134D 134DD RELAY TYPE DPDT relay with internal diode for coil transient suppression DPDT relay with internal
FBR46 SERIES. 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) MINIATURE RELAY FEATURES ORDERING INFORMATION
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR46 SERIES FEATURES Miniature size About 50% smaller in volume compared with the FBR240 series used mainly in communication equipment. High surge
LoopBack Relay. GLB363 Series. With Built-in AC Bypass Capacitors / DC LoopBack Relay
GLB363 Series With Built-in AC Bypass Capacitors / DC SERIES DESIGNATION GLB363 RELAY TYPE, Sensitive Coil, Surface Mount Ground Shield and Stub pins with AC Bypass Capacitors or No capacitor DESCRIPTION
SURFACE MOUNT HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT DC-4 GHz
SURFACE MOUNT HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT DC-4 GHz SERIES RELAY TYPE GRF7 GRF73 Repeatable, RF relay Sensitive, repeatable, RF relay DESCRIPTION The ultraminiature GRF7 and GRF73 relays
AN-B21C-0004 Applications Note
Rev. A, 10/12/09 SD 2009 Coto Technology All Rights Reserved 1/10 B21C Relay Specification Data TEST PARAMETERS CONDITIONS 1,2 MIN NOM MAX UNITS COIL SPECIFICATIONS COIL RESISTANCE 140.0 155.0 170.0 Ω
SMALL POLARIZED RELAY WITH HIGH SENSITIVITY
TESTING SMALL POLAIZED ELA WITH HIGH SENSITIVIT TF-ELAS. 9..7 mm inch FEATUES High sensitivity: 8 power (Single side stable - V type) Surge withstand: V FCC Part 68 Minimal magnetic interference allows
PCB Footprint Max.Load Coil Voltage Non-Latching part number Single-coil latching part number Standard ground terminal (1GHz)
High Frequency Relay G6K-RF Surface Mount, 1GHz / 3 GHz Miniature DPDT, High Frequency Relay New Models with 3 GHz band available ( -T versions) Space-saving 1 GHz version with smaller ground terminal
RT series Miniature Printed Circuit Board Relays, Sockets and Accessories
RT series Miniature Printed Circuit oard Relays, Sockets and ccessories pplied Coil Voltage (% of rated nom.) RT series (DC Coil) 6 mp PC oard Miniature Relay Meets VDE 0mm Spacing, KV Dielectric File
CONVENTIONAL TYPE REED RELAY EDR0 SERIES
CONVENTIONAL TYPE REED RELAY EDR0 SERIES EDR001 EDR002 EDR003 EDR007 EDR009 EDR010 EDR011 EDR012 EDR013 EDR015 EDR016 EDR018 1 FEATURES EDR0 01, 02, 03, 07, 09, 10, 11, 12, 13, 15, 16 SERIES 2.54 mm IC
SURFACE MOUNT HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT
SURFACE MOUNT HIGH REPEATABILITY, BROADBAND TO-5 RELAYS DPDT SERIES GRF300 GRF300D GRF300DD GRF303 GRF303D GRF303DD RELAY TYPE Repeatable, RF relay Repeatable, RF relay with internal diode for coil transient
JY SERIES 1 POLE 3, 5 A (MEDIUM LOAD CONTROL) POWER RELAY. RoHS compliant
POWER RELAY 1 POLE 3, 5 A (MEDIUM LOAD CONTROL) JY SERIES RoHS compliant FEATURES UL, CSA, VDE recognized High sensitivity and low power consumption High isolation Wide operating range DIL pitch terminals
FBR211 SERIES 1 POLE MINIATURE RELAY. 1 to 2 A (FOR SIGNAL SWITCHING) 1 to 3 A (FOR AUTOMOTIVE SWITCHING) FEATURES (FOR SIGNAL APPLICATIONS)
MINIATURE RELAY POLE FBR2 SERIES to 2 A (FOR SIGNAL SWITCHING) to 3 A (FOR AUTOMOTIVE SWITCHING) FEATURES (FOR SIGNAL APPLICATIONS) 2 A maximum carrying current Capable of 2 A maximum continuous carrying
JS SERIES 1 POLE 8 A (MEDIUM LOAD CONTROL) POWER RELAY. Lead Free FEATURES ORDERING INFORMATION
POWER RELAY 1 POLE 8 A (MEDIUM LOAD CONTROL) Lead Free FEATURES UL, CSA, VDE, SEV, SEMKO, FIMKO, ÖVE, BSI recognized UL class B (130 C) insulation 1 form A (SPST-NO) or 1 form C (SPDT) contact Low profile
POWER RELAY. FTR-K3-WG Series. 1 POLE - 25A - 1.5mm contact gap FTR-K1 SERIES FEATURES
FTR-K1 SERIES POWER RELAY 1 POLE - 25A - 1.5mm contact gap FTR-K3-WG Series FEATURES 1 pole, 25A 1 Form A Contact gap 1.5mm Surge strength (B/T open contacts) 2.5kV Compliance with European photovoltaic
SPECIFICATIONS Contact Form 2 Form C Maximum switching power 30 W (resistive) 62.5 VA (resistive) Contact Ratings Maximum switching voltage 220
EMAIL: The new EF2 Series miniature signal relays are designed for use in electronic switching systems, PBXs, terminal equipment, telephone equipment and instrument equipment. This series exhibits 50 mw
Suitable for lighting and motor load, 1 Form A 50A latching relays
Suitable for lighting and motor load, 50A latching relays DJ-H RELAYS (ADJH) 9.0 5 1 0.2 9.0 5 New 1 FEATURES 1. High inrush capability Tungsten load (TV-20 class) Electronic ballast load (NEMA10) Capacitive
MAGNETIC-LATCHING ESTABLISHED RELIABILITY TO-5 RELAYS DPDT RELAY TYPE. DPDT relay with internal diode for coil transient suppression
ESTABLISHED RELIABILITY SERIES DESIGNATION MAGNETIC-LATCHING ESTABLISHED RELIABILITY TO-5 RELAYS DPDT 420/422 DPDT basic relay 420D/422D 420DD/422DD RELAY TYPE DPDT relay with internal diode for coil transient
Class Sealing Fully sealed Contact configuration Rated coil voltage Model Basic Type SPDT 4.5 VDC G6Y-1 5 VDC 9 VDC 12 VDC 24 VDC
Switching Structure Based on the Micro Strip Line is Used to Combine High Performance and Costeffectiveness ROHS compliant. Isolation characteristics of 65 db or better at 900 MHz. Effective insertion
SERIES KC RELAY NONLATCH 3PDT, 25 AMP
All welded construction Contact arrangement 3 PDT configuration in one inch cube Qualified to MIL-PRF-83536 PRINCIPLE TECHNICAL CHARACTERISTICS Applicable sockets: SO-1057-8912 Contacts rated at 28 Vdc;
TEL:-3349 FAX:-332 FBR2 SERIES ORDERING INFORMATION [Example] FBR2 S A D2 U P 2 ( CSA) (a) (b) (c) (d) (e) (f ) (g) (h) (a) Series N
![TEL:-3349 FAX:-332 FBR2 SERIES ORDERING INFORMATION [Example] FBR2 S A D2 U P 2 ( CSA) (a) (b) (c) (d) (e) (f ) (g) (h) (a) Series N](/thumbs/84/91187989.jpg "TEL:-3349 FAX:-332 FBR2 SERIES ORDERING INFORMATION [Example] FBR2 S A D2 U P 2 ( CSA) (a) (b) (c) (d) (e) (f ) (g) (h) (a) Series N")
TEL:-3349 FAX:-332E-MAIL: szss@3.com FUJITSU TAKAMISAWA COMPONENT CATALOG MINIATURE RELAY POLE to 2 A (FOR SIGNAL SWITCHING) to 3 A (FOR AUTOMOTIVE SWITCHING) FBR2 SERIES FEATURES (FOR SIGNAL APPLICATIONS)
POWER RELAY. FTR-K3-WS Series. 1 POLE - High Capacity 25A Type FTR-K1 SERIES FEATURES
POWER RELAY 1 POLE - High Capacity 25A Type FTR-K3-WS Series FEATURES 1 pole, 25A 1 form A contact Wide contact gap: 1.8mm Dielectric strength (B/T open contacts) 2.5kV Compliant with European photovoltaic
PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 XXX 10X. (All dimensions are in mm [inches]) R 516 _ 1 0 _
![PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 XXX 10X. (All dimensions are in mm [inches]) R 516 _ 1 0 _](/thumbs/96/127769340.jpg "PAGE 1/6 ISSUE SERIES Micro-SPDT PART NUMBER R516 XXX 10X. (All dimensions are in mm [inches]) R 516 _ 1 0 _")
PAGE 1/6 ISSUE 15-10-18 SERIES Micro-SPDT PART NUMBER R516 XXX 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT TECHNOLOGY
10 A MINIATURE POWER RELAY mm inch. 2 Form A, 1 Form A 1 Form A. Initial breakdown voltage* 2. Vibration resistance.
VDE A MINIATURE POWER RELAY RELAYS a..9.9 SPECIFICATIONS power FEATURES.9 ab.9 Contact, Arrangement Form A Form A Form B Initial contact resistance, ma. (By drop V DC A) mω Contact material Gold flash
Relays & Sockets RU Series Universal Relays. With Latching or Momentary Lever. Standard (without lever) Key features:
RU Series Universal Relays Key features: Full featured universal miniature relays Designed with environment taken into consideration Two terminal styles: plug-in and PCB mount Non-polarized LED indicator
High breakdown voltage type is available (1.5 kv between open contacts)
TESTING High type is available (.5 kv between open contacts) TX-D RELAYS New Compliance with RoHS Directive FEATURES. Lineup now includes high type that achieves between open contacts of,5 V AC. between
Distributed by: www.jameco.com 188314242 The content and copyrights of the attached material are the property of its owner. S 4 A CAPACITY, THE VARIETY OF CONTACT ARRANEMENTS S RELAYS 28. 1.12 12..472
Classification Enclosure rating Contact form Model Standard Flux protection SPST-NO G6RL-1A
PCB Relay Low-profile power relay with maximum switching of 8 A Low profile: 12.3 mm in height Max. switching capacity: 2,500 VA (NO) Dielectric strength: 5 kv Clearance and creepage distance: 10 mm. RoHS
PAGE 1/6 ISSUE Jul SERIES Micro-SPDT PART NUMBER R516 XXX 10X R 516 _ 1 0 _
PAGE 1/6 ISSUE Jul-24-2017 SERIES Micro-SPDT PART NUMBER R516 XXX 10X R516 series: the RAMSES concept merges with the SLIM LINE technology, breaking up the frequency limits of SMT switches : - FULL SMT
Standard model G2A-432A-US G2A-4321P-US. Arc barrier equipped model G2A-432AY-US ---
Power Relay G2A Highly Reliable, 4-pole Miniature Relay Ideal for Sequence Control Card lift-off employed for greater life and stable quality. Long endurance and stable quality are assured by card lift-off
MINIATURE SIGNAL RELAYS
Information MINIATURE SIGNAL RELAYS UA SERIES (DIP Type) UB SERIES (SMD Type) TECHNICAL DATA EM Devices Corporation 17 EMDST5VOL1E17H The information in this document is based on documents issued in March,
PCB Relays Twin Relays
Features Limiting continuous current A Easiest PCB routing among all PCB relays Typical Applications Car alarm Door control Door lock Immobilizer Seat control Sun roof Window lifter Wiper control Please
SPST-NO SPDT DPST-NO DPDT
PCB Relay Next-generation PCB Relay Available in 2 Models Low profile:. mm max. in height Contains no lead inside and features cadmium-free contacts ensuring environment-friendly use. Conforms to VDE0
Distributed by: www.jameco.com -8-83-44 The content and copyrights of the attached material are the property of its owner. D HIGHLY ENITIVE 5 V FCC URGE WITHTANDING INIATURE RELAY D RELAY D4E 35.4.387