SECTION ELECTRICAL PART 1 - GENERAL 1.1 SCOPE: PROVIDE ALL ELECTRICAL WORK FOR A COMPLETE AND OPERABLE SYSTEM AS SHOWN ON THE DRAWINGS AND AS

Transcription

1

2 SECTION ELECTRICAL PART 1 - GENERAL 1.1 SPE: PROVI ALL ELECTRICAL WORK FOR A MPLETE AND OPERABLE SYSTEM AS SHOWN ON THE DRAWINGS AND AS SPECIFIED IN THIS SECTION INCLUDING, BUT NOT LIMITED TO THE FOLLOWING: A. BRANCH CIRCUIT-WIRING SYSTEM INCLUDING WIRING VICES, WIRING, NDUIT, PULL BOXES AND EQUIPMENT NNECTIONS. B. LIGHTING SYSTEM INCLUDING LIGHT FIXTURES, LAMPS, BALLASTS, REQUIRED MOUNTING HARDWARE, AND OCCUPANCY SENSORS. C. ADJUSTMENT AND TEST OF THE ELECTRICAL WORK. D. GUARANTEE. 1.2 QUALITY ASSURANCE: A. ALL PRODUCTS AND EQUIPMENT HEREIN SPECIFIED OR INDICATED ON THE DRAWINGS SHALL BE NEW WITH UL LABEL AND IN MPLIANCE WITH THE CALIFORNIA ELECTRICAL, STATE AND LOCAL S. MATERIALS FOR SIMILAR USE SHALL BE OF THE SAME TYPE AND MANUFACTURE. B. ALL WORK AND MATERIALS SHALL BE INSTALLED PER THE GOVERNING AUTHORITIES. NOTHING IN THE PLANS OR SPECIFICATIONS SHALL BE EMED AS PERMISSION TO VIOLATE THESE S OR AUTHORITIES AND THE NTRACTOR SHALL BE HELD RESPONSIBLE FOR ANY WORK, WHICH IS NOT ACCEPTED. VIOLATIONS SHOWN ON THE PLANS ARE TO BE BROUGHT TO THE ATTENTION OF THE ELECTRICAL ENGINEER BEFORE WORK IS DONE. 1.3 SITE VISITATIONS: PRIOR TO THE SUBMISSION OF THE BID, THE NTRACTOR SHALL VISIT THE SITE AND MAKE A THOROUGH EXAMINATION OF THE EXISTING NDITIONS AND THEREBY INCLU ALLOWANCES FOR THIS WORK IN THIS BID. 1.4 PERMITS AND LICENSES: NTRACTOR SHALL PAY FOR AND OBTAIN ALL NECESSARY PERMITS, INSPECTIONS, INSURANCE AND LICENSES REQUIRED FOR THE ELECTRICAL WORK. LIVER CERTIFICATES FOR ALL PERMITS AND INSPECTIONS TO THE ARCHITECT. 1.5 ORDINATION: NTRACTOR TO ORDINATE THE ELECTRICAL WORK WITH OTHER TRAS. REVIEW DRAWINGS AND SPECIFICATIONS OF ALL EQUIPMENT REQUIRING ELECTRICAL NNECTIONS PRIOR TO INSTALLATION OF THE ELECTRICAL SYSTEM. VERIFY SPACE, VENTILATION AND CLEARANCES REQUIRED TO INSTALL ELECTRICAL EQUIPMENT. EXACT LOCATIONS OF LIGHTS AND WIRING VICES ARE SHOWN ON ARCHITECTURAL DRAWINGS. 1.6 SUBMITTALS: WITHIN THIRTY (30) DAYS AFTER AWARD OF NTRACT, SUBMIT TO THE ARCHITECT SIX (6) SETS OF SHOP DRAWINGS NSISTING OF PRODUCT DATA SHEETS FOR LIGHT FIXTURES, RECEPTACLES, SWITCHES, PLATES, WIRING VICES, AND MATERIAL LIST. SUBMITTALS NOT TO INCLU SUBSTITUTIONS OR VIATIONS FROM THE MATERIALS OR METHODS SPECIFIED UNLESS PRIOR APPROVAL HAS BEEN GIVEN IN WRITING. MAKE ALL SUBMITTALS AT ONE TIME IN BOOKLET FORM. 1.7 SUBSTITUTIONS: WHERE MANUFACTURER'S NAME AND CATALOG NUMBER ARE CALLED OUT, THE PHRASE "OR APPROVED EQUAL" CAN BE ASSUMED EXCEPT THE BURN OF PROVING EQUALITY IS ON THE BIDR. 1.8 DRAWINGS: DURING PROGRESS OF WORK MAINTAIN A RERD OF CHANGES MA ON PLANS AND "AS-BUILT" LOCATIONS OF BURIED NDUITS AND DUCTS. ON MPLETION, PRESENT A PROFESSIONALLY DONE REPRODUCIBLE DRAWING TO THE ARCHITECT. 1.9 VERIFICATION OF DIMENSIONS: ALL SCALED AND FIGURED DIMENSIONS ARE APPROXIMATE AND ARE GIVEN FOR ESTIMATING PURPOSES ONLY. WHERE APPARATUS AND EQUIPMENT HAVE BEEN TAKEN FROM TYPICAL EQUIPMENT OF THE CLASS INDICATED AND BEFORE PROCEEDING WITH THE WORK, THE NTRACTOR SHALL CAREFULLY CHECK AND VERIFY ALL DIMENSIONS AND SIZES AND SHALL ASSUME ALL RESPONSIBILITY FOR THE FITTING OF HIS MATERIALS AND EQUIPMENT TO OTHER PARTS OF THE EQUIPMENT AND TO THE STRUCTURE LOCATION: PRIOR TO ROUGH-IN, MINOR ADJUSTMENTS TO OUTLET LOCATIONS MAY BE MA WITHOUT ADDITIONAL MPENSATION PROTECTION OF FINISH: FULLY PROTECT ALL FINISHED PARTS DURING THE PROGRESS OF THE WORK AND UNTIL FINAL MPLETION GUARANTEE: ALL ELECTRICAL WORK AND EQUIPMENT (EXCEPT LAMPS) SHALL BE GUARANTEED FOR ONE YEAR FROM THE DATE OF ACCEPTANCE ON NTRACTOR'S LETTERHEAD AND TURNED OVER TO THE OWNER AT THE MPLETION AND FINAL ACCEPTANCE OF THE JOB. PART 2 - PRODUCTS 2.1 CIRCUIT BREAKERS: CIRCUIT BREAKERS SHALL BE BOLT-ON MOLD-CASE TYPE WITH THERMAL MAGNETIC TRIPS. PROVI WITH RATED VOLTAGE, FRAME SIZE, NUMBER OF POLES AND TRIP SETTING AS SHOWN. NEMA INTERRUPTING CAPACITY SHALL BE 10,000 AIC AT 120/208 VOLTS OR SERIES RATED 65,000 AIC AT 277/480 VOLTS, UNLESS OTHERWISE NOTED. MATCH EXISTING. 2.2 NDUIT: NDUIT SHALL BE RIGID STEEL GALVANIZED IMC FOR UNRGROUND, EXPOSED UP TO +5'-0" OR IN DAMP LOCATIONS. NO RUNNING THREADS WILL BE PERMITTED. GALVANIZED EMT SHALL BE USED IN DRY NCEALED LOCATIONS AND EXPOSED ABOVE +5'-0". EMT NNECTORS SHALL BE WATERTIGHT MPRESSION TYPE. GALVANIZED FLEXIBLE NDUIT SHALL BE USED ONLY FOR MOTOR AND FIXTURE NNECTIONS IN LENGTHS NOT TO EXCEED 6'. NDUITS PENETRATING THE ROOF ARE TO BE FLASHED AND UNTER FLASHED. PVC SCHEDULE 40 MAY BE USED UNR FLOOR SLABS OR UNRGROUND WITH GROUND WIRE. PVC UNRGROUND TO HAVE 24 INCH VER. INSTALL FITTINGS, SPECIAL VICES AND MATERIAL, WHICH MAY BE REQUIRED FOR THE PROPER INSTALLATION OF THE NDUIT SYSTEM. 2.3 NDUCTORS: NDUCTORS SHALL BE 600 VOLT INSULATION TYPE THHN/THWN PPER. NDUCTORS AWG #10 AND SMALLER SHALL BE SOLID, AWG #8 AND LARGER TO BE STRAND. 2.4 SPLICES: SPLICES ON NDUCTORS #8 OR SMALLER SHALL BE SKOTCHLOC SPRING NNECTORS AND FOR LARGER SIZE CABLES USE SOLRLESS NNECTORS. 2.5 RECEPTACLES: RECEPTACLES, 120 VOLT DUPLEX GROUNDING TYPE, SHALL BE SPECIFICATION GRA 15 AMP LEVITON #5261-I. WHERE INDICATED WP INSTALL WEATHERPROOF GASKETED VER, MOUNTED ON FS BOX. PROVI GROUND FAULT CIRCUIT INTERRUPTERS WHERE REQUIRED BY. DICATED RECEPTACLES SHALL BE 20 AMP, LEVITON #5362-I. 2.6 LIGHT SWITCHES: SWITCHES SHALL BE TOGGLE TYPE SPECIFICATION GRA 120/277 VOLTS AC LEVITON #1201-2I AND #1203-2I FOR 3-WAY. 2.7 VOICE/DATA OUTLET: VICE SHALL BE A DUPLEX JACK OUTLET BY HUBBELL #DJOO, ORDINATE VICE WITH OWNER'S EQUIPMENT REQUIREMENTS. LOR SHALL BE AS SELECTED BY ARCHITECT. 2.8 PLATES: SHALL BE IVORY PHENOLIC. 2.9 CHANNELS: STRUCTURAL CHANNELS SHALL BE BY KINDORF, KIN-LINE OR UNISTRUT MPLETE WITH ALL FITTINGS, ACCESSORIES, SWIVELS, RODS, ETC. AND INSTALLED TO STRUCTURAL MEMBERS AS DIRECTED BY THE STRUCTURAL ENGINEER LIGHTING FIXTURES: FURNISH AND INSTALL MPLETE WITH LAMPS, BALLASTS AND REQUIRED MOUNTING HARDWARE. PRIOR TO ORRING FIXTURES, VERIFY MOUNTING METHODS AND FINISHES. ALL FLUORESCENT FIXTURES MOUNTED IN "T" BAR CEILINGS TO BE INPENNTLY SUSPEND DIAGONALLY WITH 2 #10 STEEL WIRES. INSTALLATIONS IN FIRE-RATED AREAS TO BE DONE ACRDING TO REQUIREMENTS. RECESSED PORTIONS OF FIXTURE ENCLOSURES, OTHER THAN AT POINTS OF SUPPORT, SHALL BE SPACED AT LEAST 1/2 INCH FROM MBUSTIBLE MATERIAL. THERMAL INSULATION SHALL NOT BE INSTALLED WITHIN 3 INCHES FROM THE RECESSED FIXTURE ENCLOSURE, WIRING MPARTMENT, OR BALLAST AND SHALL NOT BE SO INSTALLED ABOVE THE FIXTURE AS TO ENTRAP HEAT AND PREVENT THE FREE CIRCULATION OF AIR UNLESS THE FIXTURE IS OTHERWISE INTIFIED FOR INSTALLATION WITHIN THERMAL INSULATION. FOR PENDANT MOUNTED FIXTURES, ALIGN STEMS TO CEILING WITH LASER BEAMS LAMPS: LAMPS SHALL BE AS SHOWN ON THE FIXTURE SCHEDULE. PROVI LAMPS SUITABLE FOR THE USE INTEND. FLUORESCENT LAMPS SHALL BE 32 WATT ENERGY SAVER G.E. F32T8 RS SPX35 OR APPROVED EQUAL BY SYLVANIA OR PHILIPS. METAL HALI LAMPS TO BE ATED. PROVI MINIMUM 100 HOURS OF "BURN-IN" OF ALL FLUORESCENT LAMPS BALLASTS: A. FLUORESCENT BALLASTS SHALL BE RAPID START, IN-RUSH CURRENT LIMITING, ELECTRONIC PREMIUM TYPE CBM CERTIFIED AND ETL APPROVED, HIGH POWER FACTOR AND OF VOLTAGE REQUIRED. BALLASTS SHALL BE ADVANCE, UNIVERSAL, MAGNETEK OR MOTOROLA. BALLASTS SHALL BE MPATIBLE WITH OCCUPANCY SENSORS. HID BALLASTS SHALL BE UL LISTED FOR THE SOURCE, WATTAGE AND POSITION OF THE LAMP PROVID GROUND FAULT CIRCUIT INTERRUPTER (GFCI): PROVI GFCI CIRCUIT BREAKERS OR OUTLETS ACRDING TO THE NATIONAL ELECTRICAL SECTION 210 (2) AND (3), 210-8, AND SUCH GROUND FAULT CIRCUIT INTERRUPTER PROTECTION MAY BE PROVID FOR OTHER CIRCUITS, LOCATIONS AND OCCUPANCIES, AND WHERE USED, WILL PROVI ADDITIONAL PROTECTION AGAINST LINE-TO-GROUND SHOCK HAZARDS. PART 3 - EXECUTION 3.1 GENERAL: A. THE ELECTRICAL DRAWINGS, WHICH NSTITUTE AN INTEGRAL PART OF THIS NTRACT, SERVE AS THE WORKING DRAWINGS AND INDICATE THE GENERAL LAYOUT OF THE ELECTRICAL SYSTEMS. FIELD VERIFICATIONS OF LOCATIONS ON PLANS IS DIRECTED BY FIELD NDITIONS. CHECK THE ARCHITECTURAL, STRUCTURAL AND MECHANICAL PLANS TO AVERT POSSIBLE INSTALLATION NFLICTS AND INCLU ALL RESULTING ST IN THE BID. B. DISCREPANCIES BETWEEN DIFFERENT PLANS, BETWEEN PLANS AND ACTUAL FIELD NDITIONS, OR BETWEEN PLANS AND SPECIFICATIONS SHALL BE PROMPTLY BROUGHT TO THE ATTENTION OF THE ELECTRICAL ENGINEER FOR CLARIFICATION OR CISION. APPURTENANCES AND WIRING NOT SPECIFICALLY INDICATED OR REFERRED TO, BUT WHICH ARE MMON TO MPLETE AND OPERABLE ELECTRICAL SYSTEMS, SHALL BE INCLUD IN THE BID. C. EACH EMPTY NDUIT SHALL INCLU A PULL RD. ALL PULL RDS SHALL HAVE A MINIMUM DIAMETER OF 1/4" AND A MINIMUM AVERAGE TENSILE STRENGTH OF 1100 POUNDS. IT SHALL BE YELLOW IN LOR. A NTRASTING TRACER LOR MAY BE INCLUD TO INTIFY THE MANUFACTURER. FLAT BRAID IS NOT ACCEPTABLE. 3.2 INSTALLATION: INSTALLATION OF MATERIALS AND EQUIPMENT SHALL BE IN STRICT ACRDANCE WITH MANUFACTURER'S REMMENDATIONS, INSTRUCTIONS, INDUSTRY STANDARDS, AS INDICATED ON THE DRAWINGS AND AS SPECIFIED HEREIN. PROVI ALL MOUNTING FACILITIES FOR SECURING OR HANGING FIXTURES, EQUIPMENT AND OUTLETS TO THE SATISFACTION OF THE ENGINEER. TAILS SHOWN ON THE PLANS ARE FOR THE PURPOSE OF ESTABLISHING THE EXTENT AND GENERAL METHODS REQUIRED. PROVI ALL SLEEVES, INSERTS, EXPANSION JOINTS, VIBRATION FITTING, ETC. A. PROVI STORAGE FACILITIES AND PROTECT ALL WORK, MATERIALS AND EQUIPMENT FROM DAMAGE DURING PROCESS OF WORK. MATERIALS AND EQUIPMENT SHALL NOT BE STORED EXPOSED TO WEATHER. REPLACE ALL DAMAGED OR FECTIVE WORK, MATERIALS AND EQUIPMENT WITHOUT ADDITIONAL ST TO THE OWNER. 3.3 NDUIT AND WIRING: ALL NDUIT AND WIRING SHALL BE INSTALLED NCEALED IN WALLS, ABOVE CEILINGS AND BELOW FLOOR SLABS OR EXPOSED IN ACRDANCE WITH APPLICABLE REGULATIONS AND THE ELECTRICAL DRAWINGS. ALL PENETRATIONS OF FIRE-RATED WALLS OR CEILINGS TO BE ORDINATED WITH OWNER. NDUIT RUNS ARE SHOWN DIAGRAMMATICALLY. EXACT ROUTING AND LOCATION OF THE EQUIPMENT TO BE TERMINED IN THE FIELD. 3.4 MOISTURE PROTECTION: WHERE REQUIRED BY REGULATIONS, ALL ELECTRICAL VICES IN THE SPRAY RADIUS OF SPRINKLERS SHALL BE INSTALLED WITH WEATHERPROOF ENCLOSURES IN MPLIANCE WITH THESE REGULATIONS. 3.5 GROUNDING: ALL METALLIC NDUITS, SUPPORTS AND ENCLOSURES SHALL BE GROUND IN MPLIANCE WITH THE NATIONAL ELECTRICAL. GROUNDING BUSHINGS SHALL BE USED WHEREVER NDUITS ARE REQUIRED TO BE GROUND. 3.6 TESTING: ALL NEW CIRCUITS SHALL BE TESTED FOR SHORT AND OPEN CIRCUIT TO GROUND WITH A MEGGAR. RESISTANCE TO GROUND SHALL BE IN MPLIANCE WITH THE REQUIREMENTS OF THE NATIONAL ELECTRICAL. FURNISH ALL NECESSARY LABOR, INSTRUMENTS AND EQUIPMENT REQUIRED FOR MAKING TESTS TO MONSTRATE THAT THE OPERATION OF THE SYSTEM IS IN ACRDANCE WITH THE INTENT OF THE NTRACT DOCUMENTS. ALSO PERFORM A MPLETE "IN SERVICE" OPERATION OF THE ENTIRE ELECTRICAL SYSTEM TO THE FULL SATISFACTION OF THE OWNER. END OF SECTION

3 NO PANEL: "BD" (EXISTING) PANELVOLTAGE: 277/480 3P, 4W CIRCUIT : N : NON-NTINUOUS LOCATION: ELECTRICAL ROOM BUS: 400A L : LONG-NTINUOUS MOUNTING: SURFACE MAIN: 400A/3P CIRCUIT BREAKER AIC RATING: 65,000 (SERIES RATED) TYPE CNT. C.B. BUS C.B. TYPE CNT. M R L TR P TR P L R M EXISTING POOL PUMP N 50 3 X N SPACE N X N SPACE N X N SPACE 6 7 SPACE SPACE 8 9 SPACE SPACE SPACE SPACE EXIST PANEL "D" VIA 150 KVA N X N N X N N X N PHASE TOTALS PHASE TOTALS Total Phase A: NNECTED VA ( N): Total Phase B: NNECTED VA ( L): Total Phase C: TOTAL NNECTED KVA: LCL KVA (25% OF L): TOTAL ADJUSTED KVA (W/LCL): TOTAL PANEL AMPS: ADJUSTED AMPS W/LCL AND MAND: NO NO PANEL: "D" (SECTION 1) PANELVOLTAGE: 120/208 3P, 4W CIRCUIT : N : NON-NTINUOUS LOCATION: ELECTRICAL ROOM BUS: 400A L : LONG-NTINUOUS MOUNTING: SURFACE MAIN: LUGS ONLY R: MANDABLE RECEPTACLES AIC RATING: MATCH EXISTING K: KITCHEN TYPE CNT. C.B. BUS C.B. TYPE CNT. M R L TR P TR P L R M EXISTING WALL LTS L 20 2 X 20 2 L EXISTING POOL OVERHEAD LTS EXISTING WALL LTS L X L EXISTING POOL OVERHEAD LTS EXISTING POOL OVERHEAD LTS L 20 2 X R EXISTING RECEPTACLES EXISTING POOL OVERHEAD LTS L X 20 1 N EXISTING ROOF FANS EXISTING MENS DRESSING RM R X 20 1 L EXISTING LOBBY LIGHTS EXISTING MENS BATHRM LTS L 20 1 X 20 1 L EXISTING LOBBY LIGHTS EXISTING MENS DRESSING RM R X 20 1 L EXISTING EMERGENCY LIGHTS EXISTING LOCKER RM LTS L 20 1 X 20 1 N EXISTING ROOF HEATERS EXISTING MENS DRESSING LTS L 20 1 X R EXISTING OFFICE RECEPT EXISTING HAND DRYER N 20 1 X N SPACE EXISTING WOMENS LOCKER A/C N 30 2 X 20 1 N EXISTING LOAD N X 20 1 N MOTORIZED AUTO DOOR EXISTING HEATER #2 N 40 3 X 70 3 N EXISTING ROOF BLOWER MOTOR N X N N X N EXISTING HEATER #1 N 40 3 X 30 3 N EXISTING ROOF BLOWER MOTOR N X N N X N SPARE N 20 1 X 30 3 N EXISTING MEN'S HEATER NEW MEN'S HAND DRYER N X N SPACE N X N PHASE TOTALS PHASE TOTALS Total Phase A: NNECTED VA ( N): Total Phase B: NNECTED VA ( L): 6000 Total Phase C: NNECTED VA ( R): 2880 NNECTED VA ( K): PROVI LISTED HANDLE TIES AS REQUIRED FOR MULTIWIRE BRANCH CIRCUITS, PER N.E.C TOTAL NNECTED KVA: 50.9 MAND KVA ( R OR K): MATCH EXISTING CIRCUIT BREAKER TYPE. LCL KVA (25% OF L): 1.5 TOTAL ADJUSTED KVA (W/LCL AND MAND): 52.4 TOTAL PANEL AMPS (SECTION 1): ADJUSTED AMPS W/LCL AND MAND (SECTION 1): ADJUSTED AMPS W/LCL AND MAND (SECTION 1 & 2): NO NO PANEL: "D" (SECTION 2) PANELVOLTAGE: 120/208 3P, 4W CIRCUIT : N : NON-NTINUOUS LOCATION: ELECTRICAL ROOM BUS: 400A L : LONG-NTINUOUS MOUNTING: SURFACE MAIN: LUGS ONLY R: MANDABLE RECEPTACLES AIC RATING: MATCH EXISTING K: KITCHEN TYPE CNT. C.B. BUS C.B. TYPE CNT. M R L TR P TR P L R M EXISTING WEIGHT ROOM PANEL N X 20 1 N EXISTING POOL VAC NORTH N X R EXISTING POOL RECEPT EXISTING RECEPTACLE R X 20 1 L EXISTING POOL LIGHTS EXISTING RECEPTACLES R X 20 1 L EXISTING POOL LIGHTS EXISTING RECEPTACLES R X 20 1 L EXISTING POOL LIGHTS EXISTING LOAD N 20 1 X R EXISTING WOMENS BATHRM REC NEW WOMEN'S HAND DRYER N X R EXISTING RECEPTACLES EXISTING LOAD N 20 1 X N SPACE NEW WOMEN'S HAND DRYER N X N SPACE NEW OFFICE RECEPT. R X N SPACE NEW OFFICE RECEPT. R X N SPACE NEW OFFICE RECEPT. R X 20 1 L EXISTING WOMEN BATHRM LTS NEW OFFICE RECEPT. R X 20 1 L EXISTING WOMEN DRESSING LTS EXISTING RECEPTACLES R X R EXISTING RECEPTACLES EXISTING RECEPTACLES R X 20 1 L EXISTING WOMEN DRESSING LTS EXISTING RECEPTACLES R X 20 1 N EXISTING LOAD EXISTING RECEPTACLES R X 20 1 N EXISTING LOAD EXISTING WOMENS RECEPT R X 20 1 N EXISTING LOAD SPACE N X N EXISTING PANEL "E" SPACE N X N SPACE N X N PHASE TOTALS PHASE TOTALS Total Phase A: NNECTED VA ( N): Total Phase B: NNECTED VA ( L): 3000 Total Phase C: NNECTED VA ( R): NNECTED VA ( K): PROVI LISTED HANDLE TIES AS REQUIRED FOR MULTIWIRE BRANCH CIRCUITS, PER N.E.C TOTAL NNECTED KVA: 52.0 MAND KVA ( R OR K): -0.8 MATCH EXISTING CIRCUIT BREAKER TYPE. LCL KVA (25% OF L): 0.8 TOTAL ADJUSTED KVA (W/LCL AND MAND): 52.0 TOTAL PANEL AMPS (SECTION 2): ADJUSTED AMPS W/LCL AND MAND (SECTION 2): ADJUSTED AMPS W/LCL AND MAND (SECTION 1 & 2): NO

4

5

6

7

8

9

10