Michigan State University Construction Standards WIRING DEVICES PAGE
|
|
|
- Jayson Freeman
- 5 years ago
- Views:
Transcription
1 PAGE SECTION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. This Section includes the following: 1. This Section specifies the wiring devices for buildings and structures. 2. Provide all labor, materials, and equipment as necessary to complete all work as indicated on the drawings, and as specified herein. B. Related Sections include the following: 1. Applicable sections of Division 26 - Electrical 1.3 SUBMITTALS A. Shop Drawings: 1. Switches 2. Receptacles 3. Receptacle and switch cover plates 4. Floor boxes and all associated fittings and components 5. Relays 6. Time switches 1.4 QUALITY ASSURANCE A. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use. B. Comply with NFPA 70, National Electrical Code
2 PAGE PART 2 - PRODUCTS 2.1 SWITCHES A. Switches, single, 2 pole, 3 way, 4 way and key type, shall be lifetime quiette type, Cooper 2200 series, Hubbell HBL1200 series, Leviton 1200 series, or equal P. and S., color brown. B. Switch and pilot light combination shall consist of switch, Cooper 2200 series, and a flush neon pilot light, 125 volt with red plastic jewel, Cooper 277 or Leviton catalog no C. Switch and pilot light combination shall be Leviton catalog no. 5226, 15A., 120 VAC single pole switch and 1/25W, 125V. neon pilot light, red jewel face. D. Presswitch single, 2 pole, 3 and 4 way, shall be Hubbell 1200 series, color brown. E. Three position, two circuit, momentary contact switches shall be such as Hubbell catalog no. 1556, 15A., V. color brown or equal Cooper, Leviton, or P. and S. 2.2 RECEPTACLES A. In general, duplex receptacles shall be 20 ampere, 125 volt, 3 wire, grounding type, heavy duty, specification grade, color brown. Receptacles shall be: 1. Cooper Hubbell HBL Leviton Pass and Seymour 5362A B. 15 ampere, 125 volt, 3 wire grounding type duplex receptacles shall be heavy duty, specification grade, color brown. Receptacles shall be: 1. Cooper Hubbell HBL Leviton Pass and Seymour 5262A C. Ground fault circuit interrupter receptacles shall be specification grade 20 ampere, 125 volt, with feed through, color brown. GFCI receptacles shall be: 1. Cooper VGF20FB 2. Hubbell GF20LU 3. Leviton 7899-HF 4. Pass and Seymour 2095NA D. 15 ampere, 125 volt, 3 wire duplex receptacles with isolated ground, shall be Hubbell catalog no. IG-5262, Leviton catalog no IG, Cooper catalog no. IF5262, or equal P. & S.
3 PAGE E. 15 ampere, 125 volt, 3 wire, grounding type with transient voltage surge suppressor for computer outlets, shall be Leviton catalog no F. 20 ampere, 250 volt, 3 wire twist-lock receptacle, shall be Hubbell catalog no. 2320, Leviton catalog no. 2320, or equal Cooper or P. & S. G. 30 ampere, 125 volt, 2 pole, 3 wire receptacle shall be such as Hubbell catalog no. HBL9308, Leviton catalog no. 5371, or equal Cooper or P. & S. H. 30 ampere, 125 volt, 2 pole, 3 wire twist-lock receptacle with isolated ground, shall be Hubbell catalog no. IG-2610, Leviton catalog no IG, or equal Cooper or P. & S. I. 30 ampere, 250 volt, 2 pole, 3 wire receptacle shall be such as Hubbell catalog no. HBL9330, Leviton catalog no. 5372, or equal Cooper or P. & S. J. 30 ampere, 250 volt, 2 pole, 3 wire twist-lock receptacle, shall be Hubbell catalog no. 2620, Leviton catalog no. 2620, or equal Cooper or P. & S. K. 15 ampere, 250 volt, 3 wire grounding type, single receptacle for window a.c. unit shall be Hubbell catalog no or Leviton catalog no L. 20 ampere, 250 volt, 3 wire, single receptacle for window a.c. unit shall be Hubbell catalog no or Leviton catalog no M. 20 ampere, 250 volt, 2 pole, 3 wire, single phase, duplex receptacle shall be Hubbell catalog no or Leviton catalog no N. 20 ampere, 125/250 volt, 3 pole, 4 wire grounding, single phase receptacle shall be Hubbell catalog no. HBL8410. O. 20 ampere, 250 volt, 3 pole, 4 wire grounding, 3 phase single receptacle shall be Hubbell catalog no. HBL8420. P. Floor receptacles shall be Walker 500 AL series, G.E. Co. SP-400RG, or National no LGC. Q. Clock outlets shall be Leviton catalog no CH. Clock outlets to be mounted 6 inches to center below suspended ceiling or 7 feet above the floor in rooms without suspended ceiling. 2.3 COVER PLATES A. Switch and receptacle plates shall be stainless steel, non-magnetic type 302, such as Hubbell series, except where specified otherwise. Indicate on the drawings were the following plates should be used.
4 PAGE B. Switch and receptacle plates in corrosion areas such as chemical laboratories shall be Leviton unbreakable nylon, color brown. C. Switch and receptacle plates shall be brown bakelite, such as Hubbell series, Leviton series, or approved equal. D. Weatherproof receptacle rain tight while in use covers shall be Hubbell WP826 series, Leviton 5970 or 5990 series, or equal Cooper or P. & S. E. Weatherproof switch plates shall be Hubbell catalog no gray hypalon presswitch plate. F. Weatherproof switch plates shall be Hubbell catalog no gray hypalon presswitch plate with 125V. red pilot light. 2.4 FLOOR BOXES A. Floor box shall be Steel City Series 600 cast iron box with P60-DS bronze floor plate assembly and P60-CP bronze carpet plate (use when floor finish is carpet). 2.5 SPECIAL CONTROLS A. As specified, special controls shall be furnished by the contractor furnishing the associated equipment. These controls shall be connected by the electrical contractor. B. Refer to Mechanical Specifications. 2.6 TIME SWITCHES A. Connect time clock controlling supply, exhaust, and recirculating air fans as specified in the Mechanical Sections. Time clocks to be furnished by Mechanical Contractor. B. Time switches for outside building lights shall be Intermatic no. V45471CR Astronomic Dial Series, DPST, 40 amperes, 125 volt. When using the following paragraph for window or thru-wall air conditioners and the air conditioner load is greater than the contact rating of the time switch, use the relay specified in section C. 6 hour spring wound time switches, 20 ampere, 125 volt AC, SPST, shall be Dayton catalog no. 4A218A, without hold position, or approved equal. D. Time switches to control individual room lights shall be Intermatic catalog no. T101, SPST, 125 volt, 40 amp., or approved equal.
5 PAGE RELAYS A. Multiple pole relays shall be Square D Class 8501, Type X, 600 volt, 10 ampere, or approved equal, Westinghouse, General Electric, Challenger, Cutler-Hammer, or Siemens number of poles and type of enclosure as noted on drawing. 2.8 EMERGENCY-OFF STATION A. Emergency-off station to control contactor panel shall be such as Square D, Class 9001, Type K-15 break-glass operator with KA-2 N/O contact block, K-25 stainless steel plate, flush mounting, and KN-299 EMERGENCY-OFF legend plate. Include the following paragraph if emergency-off is to shut down air conditioning as well as contactor panel. B. Emergency-off station to control contactor panel and air conditioning system shall be such as Square D, Class 9001, Type K-15 break-glass operator with 2 KA-2 N/O contact blocks, K-25 stainless steel plate flush mounting, and KN-299 EMERGENCY-OFF legend plate. PART 3 - EXECUTION 3.1 SWITCHES A. Switches, unless otherwise noted, shall be mounted 48 inches to center above finished floor. 3.2 RECEPTACLES A. Receptacle outlets, unless otherwise noted, shall be mounted 18 inches to center above finished floor. END OF SECTION
Michigan State University Construction Standards SWITCHBOARDS, PANELBOARDS, AND CONTROL CENTERS PAGE
PAGE 262400-1 SECTION 262400 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
B. Manufacturers: Square-D, G.E. or Westinghosue.
SECTION 16470 - PANELBOARDS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. General: Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
1. This Section specifies the ethernet Category 5E data cabling system for buildings and structures.
PAGE 271200-1 SECTION 271200 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
NORTHWEST FLORIDA STATE COLLEGE MONUMENT SIGNS WITH LED DISPLAYS
PREPARED FOR: FOUNDATION PLAN & STRUCTURAL NOTES DESIGNED BY: NJB DRAWN BY: NJB REVIEWED BY: BLSE S1 PREPARED FOR: FRAMING PLANS DESIGNED BY: NJB DRAWN BY: NJB REVIEWED BY: BLSE S2 PREPARED FOR: SECTION
DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM FUME EXHAUST VENT-HOODS
DIVISION 11 EQUIPMENT SECTION PHOTO DARKROOM FUME EXHAUST VENT-HOODS PART 1 GENERAL 1.01 Scope of Work A. Provide material, accessories, tools, equipment and labor as required for the complete fabrication
A. Product Data: For each electrical identification product indicated.
SECTION 16075 - ELECTRICAL IDENTIFICATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
2.2 American National Standards Institute Corporation and its applicable standards C39.1, C80.1, C89, C84.1.
TECHNICAL SPECIFICATIONS for Single Phase, 1 to 3 KVA Power Conditioner with Regulation and Distribution Constant Power 3 (CP3) CP36508A 7/15/04 1.0 General This specification covers the electrical characteristics
Regal Series Recessed Flatwalls
Regal Series Recessed Flatwalls General Specifications The Amico Regal Series Recessed Flatwall shall be manufactured by Amico Corporation, in accordance with job specific shop drawings and documents.
POWER DELEGATOR SERIES 7200A POWER DISTRIBUTION UNIT WITH POWER CONDITIONING GENERAL SPECIFICATIONS
POWER DELEGATOR SERIES 7200A POWER DISTRIBUTION UNIT WITH POWER CONDITIONING GENERAL SPECIFICATIONS 1.0 SCOPE The following specification describes the features, design, and application of the Series 7200A
LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING
LIFE LINE PRODUCT SPECIFICATION FOR A 1 TO 3 KVA, SINGLE PHASE, POWER DISTRIBUTION SYSTEM WITH REGULATION AND CONDITIONING 1.0 General This specification covers the electrical characteristics and general
SECTION LOW-VOLTAGE ELECT. DIST. DESIGN AND CONSTRUCTION STANDARDS _ February 2015 PART I: GENERAL
PART I: GENERAL 1.01 Wiring Devices A. This section of the standard includes design requirements for wiring connections, including receptacles and switches to equipment specified in other sections. a.
SECTION COMMUNICATIONS ELECTRICAL POWER DISTRIBUTION
SECTION 16715 COMMUNICATIONS ELECTRICAL POWER DISTRIBUTION PART 1 - GENERAL 1.01 SECTION DESCRIPTION AND BASIC REQUIREMENTS A. The Electrical Power Distribution System provides power distribution from
1. All electrical switches and outlets used shall be equal to Hubbell heavy duty, specification grade or equivalent quality.
PART 1: GENERAL 1.01 Wiring Devices A. This section of the standard includes design requirements for wiring connections, including receptacles and switches to equipment specified in other sections. 1.02
SECTION SHORT CIRCUIT, COMPONENT PROTECTION, FLASH HAZARD AND SELECTIVE COORDINATION STUDY
SECTION 16075 - SHORT CIRCUIT, COMPONENT PROTECTION, FLASH HAZARD AND SELECTIVE COORDINATION STUDY PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Provide a short-circuit, component protection, flash
SECTION PANELBOARDS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 24 16 PANELBOARDS SPEC WRITER NOTE: Delete between // --- // if not applicable to project. Also, delete any other item or paragraph not applicable in the section
1.3. Pushbuttons and Indicating Lights.
.3 Pushbuttons and Indicating Lights Pushbutton Control Stations Contents Page Features.............................. V7-T-5 Product Selection M22 Assembled Control Stations........ V7-T-6 Commercial Control
PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator)
PRODUCT SPECIFICATION FOR A 15 THRU 500 kva, THREE PHASE, MODULAR POWER REGULATOR AND CONDITIONER PIRANHA 3 (3-phase, Power Conditioning Voltage Regulator) 1.0 General This specification covers the electrical
UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-26 00 00.00 20 (July 2006) ------------------------------- Preparing Activity: NAVFAC Superseding UFGS-26 00 00.00 20 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
SPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor
1993 Specifications CSJ 0177-11-131 SPECIAL SPECIFICATION 1533 Drop/Insert Multiplexor/Demultiplexor 1. Description. This Item shall govern for for the furnishing and installation of intelligent drop/insert
DIVISION 26 ELECTRICAL SECTION ELECTRICAL
DIVISION 26 ELECTRICAL SECTION 26 1000 ELECTRICAL PART 1 - GENERAL 1.1 WORK INCLUDED A. Furnish all labor, material and equipment necessary for the complete installation of the Electrical System as shown
05 Pg A75-90.qxp 6/9/2008 9:36 AM Page A75 RACO Floor Boxes
05 Pg A75-90.qxp 6/9/2008 9:36 AM Page A75 RACO Floor Boxes 05 Pg A75-90.qxp 6/9/2008 9:36 AM Page A76 A76 pq^ka^oapi=ommu=k^qflk^i=bib`qof`^i=`lab Δ déåéê~ä=^ééäáå~íáçåë o^`l=ñäççê=äçñéë=~êé=áçé~ääó=ëìáíéç
SECTION LIGHTING PART 1- GENERAL
SECTION 16500 LIGHTING PART 1- GENERAL 1.01 WORK INCLUDED A. The Contractor shall provide all lighting fixtures, panelboards, labor, material, etc., in accordance with the preceding specifications, the
MECKLENBURG COUNTY. Land Use and Environmental Service Agency Code Enforcement 9/8/10 ELECTRICAL CONSISTENCY MEETING. Code Consistency Questions
conduit? 9/8/10 ELECTRICAL CONSISTENCY MEETING Code Consistency Questions 1. Can branch circuits of different services be installed in the same Yes, see 300.3(C)(1) for conductors of different systems
Polished Brass. Stainless Steel
Specifications Thermoset SP Series Nylon TP Series Screwless Polycarbonate SWP Series 302/304 Stainless Steel Polished Brass Brushed Brass Aluminum Application Legrand's broad line of Pass & Seymour Size
SECTION DISTRIBUTION SWITCHBOARDS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 24 11 SPEC WRITER NOTES: Use this section only for NCA projects. Delete between // -- // if not applicable to project. Also delete any other item or paragraph
PREFACE ********************************************************** IT IS NOT INTENDED THAT THESE STANDARDS BE COPIED AND USED AS A SPECIFICATION!
PREFACE This publication has been prepared as a guide for Architectural and Engineering (A&E) firms in the preparation of documents for the design and construction of new structures and the remodeling
SECTION ELECTRICAL IDENTIFICATION
SECTION 16075 ELECTRICAL IDENTIFICATION PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches
SUGGESTED SPECIFICATION for Series 300 Automatic Transfer Switches PART 1 GENERAL 1.01 Scope Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, and withstand
SECTION STEEL LIGHTING STANDARDS. 1. Electrical conduit and fittings; Section
02760-1 of 5 SECTION 02760 STEEL LIGHTING STANDARDS 02760.01 GENERAL A. Description Steel lighting standards shall include, but not necessarily be limited to, furnishing and installing steel lighting poles,
PSOL. Remove mounting screws. Remove ears. Add 6" leads PSOL = #12 AWG solid PSTR = #12 AWG stranded
Switch Options Work Smarter Not Harder Arrow Hart custom configured wiring devices can match any of your complex industrial or commercial job needs, simplifying your project and maximizing your bottom
SECTION WIREWAYS FOR RADIOLOGY EQUIPMENT
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 05 36 WIREWAYS FOR RADIOLOGY EQUIPMENT SPEC WRITER NOTE: Delete between //----// if not applicable to project. Also, delete any other item or paragraph not applicable
SECTION DISTRIBUTION SWITCHBOARDS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 26 24 13 DISTRIBUTION SWITCHBOARDS SPEC WRITER NOTE: Delete between // -- // if not applicable to project. Also delete any other item or paragraph not applicable
High-impact resistant thermoplastic construction
Residential Grade Devices Receptacles TradeMaster Receptacles Tamper-Resistant Receptacles High-impact resistant thermoplastic construction Extra-long strap, Quickloop wire looping aid Long-term blade
FDM Medium Voltage Controller
1-1 LMR PLUS Product Description For over 50 years, EATON Corporation has been the industry leader in Medium Voltage Motor Control. The FDM Medium Voltage Fire Pump Controller is based on the AMPGARD controller
Floor Boxes. Concealed Service Floor Boxes. Engineering Data 663 Series. Faces Plates for 663 Floor Box. 663 Series Floor Box
Concealed Service Floor Boxes 663 Series Floor Box 663-SC Multiple service floor box that delivers power, communications and data from standard conduit with no exposed service fitting Result: Open office
Flush Round Single or Multi-Service Non-Metallic Concrete Floor Box Floor Boxes
Flush Round Single or Multi-Service Non-Metallic Concrete Floor ox Flush Round Single or Multi-Service Non-Metallic Concrete Floor ox Dimensions Inches (mm) D C PF1 Min. Depth of Pour 3.00" (76.2) Capacity
1995 Metric CSJ SPECIAL SPECIFICATION ITEM Add/Drop Multiplexor/Demultiplexor
1995 Metric CSJ 0113-13-109 SPECIAL SPECIFICATION ITEM 6225 Add/Drop Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent Add/Drop Multiplexor/Demultiplexor
High Performance Nylon Wallplates. Nylon Wallplates
Commercial Grade IVORY 80701-I N1-I BLACK 80701-E N1-BK GRAY 80701-GY N1-GRY RED 80701-R N1-RED WHITE 80701-W N1-W BROWN 80701 N1 1-Toggle ALMOND 80701-A N1-A IVORY 80709-I N2-I BLACK 80709-E N2-BK GRAY
Power Processor - Series 700F 10KVA to 150KVA
Power Processor - Series 700F 10KVA to 150KVA Power Conditioning and Regulation for Commercial & Industrial Equipment General Specifications PART 1 - GENERAL 1.1 DESCRIPTION This specification defines
BID ADDENDUM NO. 4 ITB/004/16/KL CITY OF WINTER SPRINGS WTP NO. 1 WATER QUALITY IMPROVEMENTS
BID ADDENDUM NO. 4 ITB/004/16/KL CITY OF WINTER SPRINGS WTP NO. 1 WATER QUALITY IMPROVEMENTS March 17, 2016 To prospective bidders & others concerned: This addendum sets forth changes and/or information
S&C Series 2000 Circuit-Switchers Outdoor Transmission (69 kv through 230 kv)
Outdoor Transmission (69 kv through 230 kv) Detailed Functional Specification Guide 1.0 GENERAL 1.01 The circuit-switcher shall conform to the following specification. 1.02 The circuit-switcher shall be
SPECIFICATION FOR HORIZONTAL AIRFLOW OUTDOOR RESISTIVE LOAD BANK
SPECIFICATION FOR HORIZONTAL AIRFLOW OUTDOOR RESISTIVE LOAD BANK PART 1.0 GENERAL 1.1 SCOPE A. This specification contains the minimum requirements for the design, manufacture and testing of a UL listed,
Wall Plates & Specialties
Molded of rugged.065" thick polycarbonate. Seamless, sleek, super smooth construction provides no dirt-catching channel around plate s perimeter. & Specialties An extra 1/8" width and height than standard
APPLICATION COMMERCIAL, INDUSTRIAL AND RESIDENTIAL; SCREW MOUNTED Gen Purpose Wiring Devices - Wall Plates & Covers
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 AllenWatson@elliottelectric.com PJSE7I Single End Plate Ivory Pass & Seymour/Legrand Catalog Number Manufacturer Description
CSI MasterFormat Specification. Wireless Remote Transmitter
Specification Wireless Remote Transmitter SSQRTM-CSI-Spec Rev. 3 July 2015 This product specification is written according to the Construction Specifications Institute (CSI), MasterFormat, SectionFormat,
Ductwork Controls and Instrumentation Outlets (HVAC) HVAC Control System.
SECTION 15910 DUCT ACCESSORIES PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15890 - Ductwork. 2. 15900 - Controls and Instrumentation. 3. 15940 - Outlets (HVAC). 4. 15970 - HVAC Control System.
1995 Metric CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor
1995 Metric CSJ 3256-02-049 1.0 Description SPECIAL SPECIFICATION ITEM 6093 Drop/Insert Multiplexor/Demultiplexor This Item shall govern for the furnishing and installation of intelligent drop/insert multiplexor/demultiplexors
AMPCO PRODUCTS, INC. TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS TECHNICAL SPECIFICATIONS SOLID PHENOLIC CORE TOILET COMPARTMENTS A. Drawings and General Provisions of Contract, including General and Supplementary Conditions and
SECTION TRANSFORMERS
SECTION 16460 - TRANSFORMERS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. General: Drawings and general provisions of the Contract, including General and Supplementary Conditions and Specification Section
SECTION CABLE TRAYS
SECTION 16139 CABLE TRAYS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
St. Monica Food Pantry
St. Monica Food Pantry 26 5113-1 ELECTRICAL WORK DIVISION 26 SECTION 265113 INTERIOR LIGHTING FIXTURES PART 1. GENERAL 1.1 WORK INCLUDES A. Extent, location, and details of interior lighting fixture work
SECTION EQUIPMENT WIRING
PART 1 - GENERAL 1.01 RELATED DOCUMENTS: SECTION 26 27 17 EQUIPMENT WIRING A. The Conditions of the Contract and applicable requirements of Divisions 0 and 1 and Section 26 00 01, Electrical General Provisions,
LOW PRESSURE STEEL DUCTWORK Mechanical Systems Insulation Outlets (HVAC) Testing and Balancing.
SECTION 15841 LOW PRESSURE STEEL DUCTWORK PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15180 - Mechanical Systems Insulation. 2. 15940 - Outlets (HVAC). 3. 15991 - Testing and Balancing. 1.02 SUBMITTALS
UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-08 33 13 (May 2009) Change 2-11/12 --------------------------- Preparing Activity: USACE Nontechnical Title Revision (August 2015) UNIFIED FACILITIES GUIDE SPECIFICATIONS
(1) F COAXIAL CONNECTOR, (1) RJ11 MODULAR JACK. Application Telephone, CATV; Approval UL 514/1683, CSA
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 26TELTVWCC10 Coax & CAT5 Dcor Device Pass & Seymour/Legrand Catalog Number Manufacturer Description Weight per unit Product
SECTION CONCRETE REINFORCEMENT FOR STEAM UTILITY DISTRIBUTION
PAGE 032015-1 SECTION 032015 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification sections,
Moveable Workstations. Enterprise KEWAUNEE. encouraging new discovery...worldwide
Enterprise Moveable Workstations KEWAUNEE encouraging new discovery...worldwide Movable Workstations Self-supporting workstations Single and double sided Adjustable height worksurfaces Integrated shelving
KidsAbility Guelph Hub Renovation ADDENDUM #2 Project No.:
KidsAbility Guelph Hub Renovation ADDENDUM #2 This Addendum amends and forms part of the Bidding and Contract Documents for the above Project as follows: CLARIFICATIONS Q1. Is it possible to set up a secondary
CLOSED CIRCUIT TELEVISION SYSTEM (CCTV) DOCUMENT NUMBER: APPLICATION: MIDDLE AND HIGH SCHOOL
CLOSED CIRCUIT TELEVISION SYSTEM (CCTV) DOCUMENT NUMBER: 16750 APPLICATION: MIDDLE AND HIGH SCHOOL DATE OF ISSUE: 11-10-04 - Revised to include hardware list and to require test results 07-05-02 - deleted
SWP26BN Brush Nickel Cover. Descriptions. Manufacturer Information PASS & SEYMOUR GTIN Manufacturers Part Number UPC
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 AllenWatson@elliottelectric.com SWP26BN Brush Nickel Cover Pass & Seymour/Legrand Catalog Number Manufacturer Description
SECTION MECHANICAL IDENTIFICATION
SECTION 15190 MECHANICAL IDENTIFICATION PART 1 - GENERAL 1.01 SUMMARY A. Section Includes: 1. Identification of mechanical products installed under Division 15. B. Related Sections: 1.02 REFERENCES 1.
Symphony II Adaptable Table System
Symphony II Adaptable Table System 1.00 General 1.01 Conditions 1.02 Scope of work 1. This section covers all materials, equipment, tools and labor for the supply and installation of the laboratory Symphony
SECTION IDENTIFICATION FOR ELECTRONIC SAFETY AND SECURITY
SECTION 280553-IDENTIFICATION FOR ELECTRONIC SAFETY AND SECURITY PART 1 - GENERAL 1.1 DESCRIPTION A. This specification section covers the furnishing and installation of nameplates, labels, wire markers,
SECTION GPS WIRELESS CLOCK SYSTEMS
PART 1 GENERAL 1.1 SECTION INCLUDES A. G.P.S. Receiver B. Primary Transmitter C. Satellite Transmitter D. Analog Clocks E. Digital Clocks 1.2 REGULATORY REQUIREMENTS SECTION 27 53 13 GPS WIRELESS CLOCK
Piping & Equipment Identification
Piping & Equipment Identification Part 1 General 1.01 Description of Work A. Work in this section includes: Identification materials, including necessary accessories indicated on Contract Documents and
CITY OF NEW ROCHELLE RENOVATIONS TO FIRE STATION NO WEBSTER AVENUE, NEW ROCHELLE, NEW YORK
AREVIATIONS AFF AOVE FINISHED FLOOR AHJ AUTHORITIES HAVING JURISDICTION APPROX APPROXIMATE LDG UILDING CLG CEILING CONST CONSTRUCTION CD CEILING DIFFUSER CO CARON DIOXIDE CXA COMMISSIONING AGENT DEG DEGREES
1. ASME A Scheme for the Identification of Piping Systems.
SECTION 40 05 53 - IDENTIFICATION FOR PROCESS PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Nameplates. 2. Tags. 3. Stencils. 4. Pipe markers. 5. Labels. 6. Lockout devices. B. Related Requirements:
ADDENDUM NO. 3 PROJECT: COURTLAND PUMP STATION CONTRACT: IFB NO COM.00030
ADDENDUM NO. 3 PROJECT: COURTLAND PUMP STATION CONTRACT: IFB NO. 2018-008-COM.00030 To: Prospective Bidders of Record Date: January 8, 2019 The following changes, additions, revisions, and/or deletions
A. Deviation from this standard must be approved by the Project Architect.
September 2012, rev. 00 26 5600 Exterior Lighting PART 1. GENERAL 1.01 Related Documents A. Deviation from this standard must be approved by the Project Architect. B. Drawings and general provisions of
A. This Section includes plumbing fixtures and related components.
SECTION 224200 PLUMBING FIXTURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
24 HOUR TIME CONTROLS
http://waterheatertimer.org/paragontimersandmanuals.html http://waterheatertimer.org/pdf/intermaticcrossreference.pdf HOUR TIME CONTROLS 00, 0 and 0 Series One and One Half Hour Minimum ON or OFF Time
Polished Brass. Stainless Steel
Specifications Thermoset SP Series Nylon TP Series Screwless Polycarbonate SWP Series 302/304 Stainless Steel Polished Brass Brushed Brass Aluminum Application Legrand's broad line of Pass & Seymour Size
WALL PLATES & SPECIALTIES
& SPECIALTIES SWP26LA Screwless Polycarbonate Wall Plates A F A. Molded of rugged.065" thick polycarbonate. B. Seamless, sleek, super smooth construction provides no dirt-catching channel around plate
UFGS-16553N (Septermber 1999) UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-26 55 80.00 20 (April 2006) -------------------------------- Preparing Activity: NAVFAC Replacing without change UFGS-16553N (Septermber 1999) UNIFIED FACILITIES GUIDE
1993 Specifications CSJ SPECIAL SPECIFICATION ITEM Drop/Insert Multiplexor/Demultiplexor
1993 Specifications CSJ 0008-12-071 SPECIAL SPECIFICATION ITEM 6550 Drop/Insert Multiplexor/Demultiplexor 1.0 Description. This Item shall govern for the furnishing and installation of intelligent drop/insert
Title: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: Electrical Standards
Change History Date Description of Change Pages / Sections Modified 8/23/17 Updated sections on System Design and Performance Requirements; Submittals; Equipment; Accessories or Special Features; Quality
SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver
2004 Specifications CSJ 0050-09-071, 0027-13-205, 0271-14-228, 0500-03-042, 0050-09-070, 0050-09-069 etc, 0050-08-086, 0050-08-087 & 0500-03-577 SPECIAL SPECIFICATION 1118 Data Fiber Optic Transceiver
SECTION CABLE TRAYS FOR COMMUNICATIONS SYSTEMS
SECTION 270536 - CABLE TRAYS FOR COMMUNICATIONS SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
SECTION AUTOMATIC TRANSFER SWITCH
SECTION 26 36 23 PART 1 - GENERAL 1.1 THE REQUIREMENT A. Furnish and install automatic transfer switches (ATS) with number of poles, amperage, voltage, withstand and close-on ratings as shown on the plans.
UNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-26 53 00.00 40 (November 2015) ----------------------------------- Preparing Activity: NASA Superseding UFGS-26 53 00.00 40 (November 2008) UFGS-26 53 00 (August 2008)
SECTION SIGNAGE
SECTION 10 14 00 SIGNAGE PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section, apply
1. Field measurements must be taken to verify existing conditions prior to installation.
General Conditions: 1. Field measurements must be taken to verify existing conditions prior to installation. 2. Deliver and set in place all food service equipment as specified herein, including that which
DESIGN INSTRUCTIONS TO ARCHITECTS AND ENGINEERS [ ] SCHEMATICS [ ] DESIGN [ ] CONSTRUCTION
![DESIGN INSTRUCTIONS TO ARCHITECTS AND ENGINEERS [ ] SCHEMATICS [ ] DESIGN [ ] CONSTRUCTION](/thumbs/81/83280225.jpg "DESIGN INSTRUCTIONS TO ARCHITECTS AND ENGINEERS [ ] SCHEMATICS [ ] DESIGN [ ] CONSTRUCTION")
DEPARTMENT OF VETERANS AFFAIRS DESIGN INSTRUCTIONS TO ARCHITECTS AND ENGINEERS LOCATION : VAMC, PROJECT TITLE : PROJECT NO. : [ ] SCHEMATICS [ ] DESIGN [ ] CONSTRUCTION DEVELOPMENT DOCUMENTS EQUIPMENT
NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY. Section ELECTRICAL IDENTIFICATION
PART 1 GENERAL 1.01 SUMMARY Section 16195 A. This Section includes electrical identification for the following: 1. Nameplates and labels 2. Wire and cable markers 3. Conduit markers 4. Cable tray markers
1995 Metric CSJ SPECIAL SPECIFICATION ITEM Multimode Video Fiber Optic Transmission Equipment
1995 Metric CSJ 3483-01-010 SPECIAL SPECIFICATION ITEM 6329 Multimode Video Fiber Optic Transmission Equipment 1.0 Description. This Item shall govern for the furnishing and installation of Video Fiber
AMP Power Lock Connectors
Product Facts High current handling capability: 31 or 53 amperes maximum depending on application (reference product specs) Modular housings for multiple connector applications Assortment of mounting accessories
Crane Control Class 7001
Catalog 17 CONTENTS Description.....................................................Page.................................................. 0 ST DC Static Timer............................................
WESTERN UNDERGROUND COMMITTEE GUIDE 2.6 (2.6/00/0868)
WESTERN UNDERGROUND COMMITTEE GUIDE 2.6 (2.6/00/0868) THREE-PHASE SUBSURFACE UNDERGROUND COMMERCIAL DISTRIBUTION (UCD) TRANSFORMER NOTE: This "Guide" summarizes the opinions, recommendations, and practices
PROJECT LOCATION BOZEMAN HIGH SCHOOL. ELECTRICAL ENGINEER: Van Dykken Engineering 37 Spanish Peak Drive Bozeman, MT Phone:
DRAWING INDEX GENERAL C. PROJECT COVER G-WING A/V IMPROVEMENTS.0 AREA PLAN ST FLOOR SOUTH. TYP. PROJECTOR MOUNTING & PROJECTOR NOTES.2 G-WING TECHNOLOGY CABINET ELEVATIONS.3 G-WING WIRING DIAGRAM.4 G-WING
MV ELECTRICAL TRANSMISSION DESIGN AND CONSTRUCTION STANDARD. PART 1: GENERAL 1.01 Transformer
PART 1: GENERAL 1.01 Transformer A. This section includes liquid filled, pad mounted distribution transformers with primary voltage of 12kV or 4.16kV (The University will determine primary voltage), with
HOENER ASSOCIATES INC. ARCHITECTS
HOENER ASSOCIATES INC. ARCHITECTS BRUCE D. DELL MARK REUTHER ADDENDUM NO. 1 PROJECT 15-22C RENOVATION AND SITE WORK AT: BUILDING B DDRB OF ST. CHARLES DEVELOPMENT DISABILITIES RESOURCE BOARD ST. CHARLES,
The School District of Palm Beach County Project Name SDPBC Project No. SECTION ( ) SIGNAGE PART 1 GENERAL 1.1 RELATED DOCUMENTS
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 10441 (10 14 00) SIGNAGE A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section,
Excavating, Backfilling, and Compaction for Utilities Piping (Plumbing).
SECTION 15047 - IDENTIFICATION PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Identification including necessary accessories indicated on Construction Documents and specified in this section or as required
Page PRODUCT DESCRIPTION
Page 1 2004-02-29 PRODUCT FEATURES BASIC USES / RELATED USES Identification bands or markings for facility piping. BradySnap-On / Strap-On Vinyl: For normal duty, mechanically fastened. Custom or Blank
SECTION IDENTIFYING DEVICES
PART 1 GENERAL 1.1 RELATED DOCUMENTS SECTION 10441 IDENTIFYING DEVICES A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division-1 specification section,
A. Radius elbows with a construction radius of 1.5 the duct width are preferred to square elbows.
SECTION 233100 DUCTWORK 1.0 Acoustical duct lining in any part of the duct system is prohibited. All ductwork requiring insulation shall be externally insulated (Refer to the Sheet Metal Ductwork Insulation
Product Guide Specification
Product Guide Specification Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat,
2. All work and materials shall be in full accordance with Local and State ordinance and with any prevailing rules and regulations.
General Conditions: 1. Deliver all food service equipment as specified herein, including that which is reasonably inferred, with all related items necessary to complete work shown on contract drawings
NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY PRESSURE GAUGES, Section 15130
PART 1 GENERAL 1.01 SUMMARY Section 15130 PRESSURE GAUGES, This Section includes the furnishing and subsequent installation of pressure gauges and pressure level transmitters as shown on Plans and specified
B. Division-16 Basic Materials and Methods section apply to work specified in this section.
Section 16745 PREMISE CABLING SYSTEMS PART ONE GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification