Quad Audio Switch REV. B BLOCK DIAGRAM OF ONE SWITCH CHANNEL
|
|
- Ashlynn Collins
- 6 years ago
- Views:
Transcription
1 a FEATURES CIickless Bilateral Audio Switching Four SPST Switches in a -Pin Package Ultralow khz ( V rms, R L = k ) Low Charge Injection: 3 pc typ High OFF Isolation: db typ (R L = khz) Low Crosstalk: 9 db typ (R L = khz) Low ON Resistance: 8 typ Low Supply Current: 9 A typ Single or Dual Supply Operation: + V to + V or. V to V Guaranteed Break-Before-Make TTL and CMOS Compatible Logic Inputs Low Cost-Per-Switch BLOCK DIAGRAM OF ONE SWITCH CHANNEL DIGITAL LOGIC INTERFACE AND BREAK-BEFORE-MAKE Quad Audio Switch SSM RAMP GENERATOR PIN CONNECTIONS Epoxy Mini-DIP (P Suffix) and SOIC (S Suffix) SW A SW B GENERAL DESCRIPTION The SSM integrates four SPST analog switches in a single -pin package. Developed specifically for high performance audio applications, distortion and noise are negligible over the full operating range of Hz to khz. With very low charge injection of 3 pc, clickless audio switching is possible, even under the most demanding conditions. Switch control is realized by conventional TTL or CMOS logic. Guaranteed break-before-make operation assures that all switches in a large system will open before any switch reaches the ON state. Single or dual supply operation is possible. Additional features include db OFF isolation, 9 db crosstalk and 8 Ω ON resistance. Optional current-mode switching permits an extended signal-handling range. Although optimized for large load impedances, the SSM maintains good audio performance even under low load impedance conditions. SW A SW B SW SW NC* SW B SW A SW SW O TOP VIEW (Not SSM to Scale) SW SW SW3 NC = NO CONNECT SW A SW B SW SW3 *CONNECT TO ANALOG GROUND FOR BEST NOISE ISOLATION SW3 B SW3 A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. One Technology Way, P.O. Box 9, Norwood, MA -9, U.S.A. Tel: 7/39-7 Fax: 7/3-873
2 SSM SPECIFICATIONS (V S = V, T A = + C, unless otherwise noted. Typical specifications apply at T A = + C.) Parameter Symbol Conditions Min Typ Max Units AUDIO PERFORMANCE Total Harmonic Distortion Plus Noise khz, with 8 khz Filter, R L = kω, V IN = V rms.8 % Spectral Noise Density e n Hz to khz.8 nv/ Hz Wideband Noise Density e n p-p Hz to khz. µv p-p ANALOG SIGNAL SECTION Analog Voltage Range V A V INH =. V, I A = ± ma ± V Analog Current Range I A V INH =. V, V A = V ± ma ON Resistance R ON I A = ± ma, V A = ± V dc 8 Ω R ON Matching R ON Match I A = ± ma, V A = V % ON Leakage Current I S(ON) V A = ± V. + na OFF Leakage Current I S(OFF) V A = ± V. + na Charge Injection Q 3 pc ON-State Input Capacitance C ON V A = V rms 3 pf OFF-State Input Capacitance C OFF V A = V rms 7 pf OFF Isolation I SO(OFF) V A = mv rms, f = khz, R L = kω db Channel-to-Channel Crosstalk C T V A = mv rms, f = khz, R L = kω 9 db SECTION Digital Input High V INH = V. V S V Digital Input Low V INL = V.8 V Turn-On Time t ON See Test Circuit 8 ms Turn-Off Time t OFF See Test Circuit 3 ms Break-Before-Make Time Delay t ON -t OFF 3 ms Logic Input Current Logic HI V INH =. V.3 + na Logic LO V INL =.8 V. + na POWER SUPPLY Supply Voltage Range V S Single Supply + + V Dual Supply ±. ± V Positive Supply Current I SY+ All Channels On.9 ma Negative Supply Current I SY All Channels On.. ma Ground Current All Channels On..3 ma NOTES Turn-on time is measured from the time the logic input reaches the % point to the time the output reaches % of the final value. Turn-off time is measured from the time the logic input reaches the % point to the time the output reaches % of the initial value. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS Supply Voltage Single Supply V Dual Supply ±3. V Analog Input Voltage (V A ) V S Logic Input Voltage (V INL/INH ) V S Maximum Current Through Any Switch ma Operating Temperature Range C to +8 C Storage Temperature Range C to + C Junction Temperature (T J ) C Lead Temperature (Soldering, sec) C Thermal Resistance -Pin Plastic DIP (P): θ JA = 7, θ JC = C/W -Pin SOIC (S): θ JA = 9, θ JC = C/W NOTE θ JA is specified for worst case mounting conditions, i.e., θ JA is specified for device in socket for P-DIP package. ORDERING GUIDE Operating Temperature Package Model Range Package Option* SSMP C to +8 C -Pin Plastic DIP N- SSMS C to +8 C -Pin SOIC R- *N = Plastic DIP, R = SOIC.
3 SSM V A (IN) = mvrms f = Hz TO khz V A (IN) Ω R = kω AND kω L OFF ISOLATION = LOG VA (IN) OFF Isolation Test Circuit LOGIC INPUT V A (IN) LOW HIGH.V t tr ns f ns DC VOLTAGE CLOSED.V LOW Figure. Headroom (V S = ± V, f = khz, with 8 khz Filter) OPEN % % OPEN. t ON t OFF t ON /t OFF Timing Diagram. +V THD + N %. V A (IN) SWITCH CONROL. GND V. k k k LOAD RESISTANCE Ω Test Circuit for t ON /t OFF Timing Specification, t ON /t OFF Switching Response, and ON/OFF Transition Photos Figure 3. THD+N vs. Load (V S = ± V, V A = V rms, f = khz, with 8 khz Filter). THD + N %. Figure. THD+N vs. Frequency (V S = ± V, V A = V rms, with 8 khz Filter). ± ±8 ± SUPPLY VOLTAGE V Figure. THD+N vs. Supply Voltage (V A = V rms, f = khz, R L = kω, with 8 khz Filter) 3
4 SSM 9. OUTPUT VOLTAGE SWING V RMS T A = C f = khz Figure. Frequency Response (V S = ± V, V A = V rms, R L = kω). k k k LOAD RESISTANCE Ω Figure 8. Output Voltage Swing vs. Load Resistance 9 CH A: 8.µV FS MKR:.µV/ Hz.µV/DIV OUTPUT VOLTAGE SWING V RMS T A = C R L = kω f = khz.% THD + N Hz MKR: Hz khz BW: Hz Figure. SSM Spectral Noise Density e n [ Devices ( Switches) Chained Together] ± ± ±8 ± ± SUPPLY VOLTAGE Volts Figure 9. Output Voltage Swing vs. Supply Voltage 3 T A = C V A = mv RMS V 9 V % V V µs INPUT OUTPUT Figure 7. Square Wave Response (T A = + C, V S = ± V, R L = kω, f = khz) OFF ISOLATION db R = k L R = k L k k k FREQUENCY Hz Figure. OFF-Isolation vs. Frequency
5 SSM CROSSTALK db R = k L T A = C V A = mvrms R = k L SWITCH LEAKAGE CURRENT na 3 V INL=.8V R L = C TO +8 C k k k FREQUENCY Hz Figure. Channel-to-Channel Crosstalk vs. Frequency (Worst Case Conditions, as Measured Between Switches and, or and 3) ANALOG INPUT VOLTAGE Volts Figure. Leakage Current vs. Analog Voltage R L = I A = ma 8 V A = ±V R L = ON RESISTANCE Ω 3 +8 C + C C SWITCHING TIME ms 8 T ON T OFF ANALOG INPUT VOLTAGE Volts Figure. ON Resistance vs. Analog Voltage 8 TEMPERATURE C Figure. Switching Time vs. Temperature 9. SWITCH LEAKAGE CURRENT ma T A = C R L = V =.8V IL V =.V IH SUPPLY CURRENT ma V A = GND V INH =.V I SY+ I SY I GND.8 ANALOG INPUT VOLTAGE Volts Figure 3. Overvoltage Characteristics. 8 TEMPERATURE C Figure. Supply Current vs. Temperature
6 SSM V V 9 V % ms/div ANALOG OUTPUT LOGIC INPUT V INL/INH SSM can also be configured as a : multiplexer, or by using additional packages, as 8: or : and up. The breakbefore-make feature is guaranteed from part to part allowing such multiple-package applications. As Figure shows, the SSM is easy to use, and no additional devices are needed. The load resistors are recommended for improved OFF-isolation and charge injection. The ON resistance of the switch is only 8 Ω typically, which causes very little signal attenuation even with a load resistor. Figure 7. t ON /t OFF Switching Response OUT R L IN 3 SW SW 9 8 IN R L OUT 9 SW SW TOP VIEW (Not to Scale) SSM 7 +V SW SW3 OPEN (SWITCH OFF) % mv µs CLOSED (SWITCH ON) OUT R L IN SW SW3 R IS OPTIONAL L 3 V R L IN3 OUT3 SW SWITCH STATE OFF ON Figure 8. Switch OFF-to-ON Transition (R L = kω) CLOSED (SWITCH ON) 9 % mv µs OPEN (SWITCH OFF) Figure 9. Switch ON-to-OFF Transition (R L = kω) APPLICATIONS INFORMATION The SSM integrates four analog CMOS switches with guaranteed break-before-make operation to provide high quality audio switching. Each switch has complementary N-channel and P-channel MOSFETs to allow the analog input voltage range to include the positive and negative rails and improve linearity. In addition, the topology permits fully bilateral switching. When using the SSM there is full flexibility in configuring the switches. For example, they can be used individually as shown in Figure, or as a double-pole, double-throw (DPDT) switch, which is explained later. The Figure. Basic Circuit Configuration OPTIMIZING PERFORMANCE As the performance curves show, the switch is optimized for high impedance loads. The distortion performance is at its best when the switch has a load impedance of kω or greater as shown in Figure. However, even at lower values of load resistances, the khz distortion performance is still excellent,.% for a kω load. The main trade-off with THD is OFF-isolation and crosstalk. This is shown in Figures and, again with two different load conditions. As these graphs show, the kω load yields approximately a db improvement in both characteristics. Thus, the optimum operating point depends on the most critical parameters. When THD is critical then high load impedances should be used; however, when crosstalk and OFFisolation are critical, lower impedances on the order of kω should be used. An additional benefit of using the smaller load resistor is that any charge injected onto the output will be shunted to ground through the resistor. If improved OFFisolation is needed, the SSM dual audio switch should be considered with its excellent db OFF-isolation at khz. It is important that all of the pins be connected to the system analog ground. These pins isolate the input and output of each switch. Without connecting these pins, the OFFisolation will degrade significantly.
7 SSM DETAILED SWITCH OPERATION A simplified circuit schematic with the functional sections is shown in Figure. The TTL interface has an internally regulated V to ensure TTL logic levels regardless of the supply voltage. The logic threshold is with respect to the pin, which can be offset. For example, if is connected to the negative supply, then the SSM will operate with negative rail logic. The interface shifts the control logic down to the negative supply and inverts it to drive N. SW TTL INTERFACE na N C pf BREAK-BEFORE-MAKE P N P na P3 N3 RAMP GENERATOR Figure. Simplified Schematic BIAS C pf N SW A SW B N in combination with C and the na current source provides the break-before-make operation of the switch. When the switch is on, N is off and C is charged up to the positive rail. However, when the SW is turned off, then the gate of N is pulled high. This turns N on, providing a low impedance path to quickly discharge C to the negative rail, which quickly breaks the switch. On the other hand, when the SW goes high again, the gate of N is pulled low, turning it off. This leaves C to be slowly charged up to the positive rail by the na current source. The difference in the discharge and charging times ensures break-before-make operation, even from device to device. The voltage on C is inverted by P to drive the ramp generator differential pair, consisting of P, P3 and N, N3. This differential pair steers the na of tail current to either charge or discharge C. As discussed above, when the switch is on, C is charged up to the positive rail. P inverts this, putting a low voltage equivalent to the negative supply on the gate of P. The BIAS voltage is approximately equal to the midpoint of the two supply voltages. Thus, when P is pulled down, it is turned on and P3 is off. All of the na flows through N and is mirrored by N3. Thus, the na discharges C through N3. When C is pulled low, the inverter turns N on by pulling its gate high, and the second inverter turns P on. To turn the switch off the gate of P is pulled above the BIAS so that all na charges C through P3. This is then inverted to turn off N and P. The internal ramp has rise and fall times on the order of a few milliseconds which is sped up by the inverters. As the gate P voltages of N and P are changing, the ON resistance of each switch is ramping from its OFF state to 8 Ω and vice versa. The actual rise and fall times are shown in Figures 8 and 9 for a kω load. These times are significantly slower than typical switches, minimizing the SSM s charge injection and giving it clickless performance. DOUBLE-POLE DOUBLE-THROW SWITCH The SSM is ideal as a one-chip solution for a stereo switch. The schematic in Figure shows the typical configuration. This circuit will select one of two stereo sources, channel A or B. The switch controls for the left and right input of each channel are tied together so that both will be turned on or off simultaneously. An inverter is inserted between the channel A and B controls so that only one logic signal is needed. The outputs can be configured many different ways, such as an inverting or noninverting amplifier stage, and the kω load resistors are added to improve the OFF-isolation. The performance of this stereo switch is equivalent to each individual switch, yielding a high quality audio switch that is virtually transparent to the signal. SSM 8 L INA SW 3 L INB SW SW SWA/SWB 9 SW3 SW 9 SW R INA R INB SW3 SW L OUT kω SWA/SWB R OUT kω CHANNEL SELECTED Figure. Double-Pole, Double-Throw Stereo Switch VIRTUAL GROUND SWITCHING The SSM was built on a CMOS process with a V operating limit for the total supply voltage across the part. This leads to a corresponding limit on the analog voltage range. However, to achieve larger signal swings, the SSM should be configured in the virtual ground mode. As shown in Figure 3, the output of the SSM is connected to the inverting input of an amplifier. Since the noninverting input is grounded, the SSM will also be biased at ground, and large voltage swings on the circuit s input will not significantly change the voltage on the switch. The only limitation is that the current through the switch needs to be less than ± ma, and the voltage range is limited only by the op amp and its supply voltages. B A 7
8 SSM The circuit was tested with an SSM3 high slew rate audio amplifier and the results are shown in Figures and. This configuration yields excellent THD performance that is primarily determined by the amplifier. Also, the headroom is now + dbu ( dbu =.77 V rms), which is due to the amplifier s output voltage swing. Thus, even though the SSM has a ± V limitation on its supplies, it can be used in systems with much higher voltage ranges. For example, the double-pole double-throw switch from Figure can be reconfigured in the virtual ground mode to allow higher voltage swings, as shown in Figure. This application realizes the excellent performance of Figures and while providing a low cost switching solution. AUDIO IN N9 R kω +V SSM SW A 3 SW B R kω +8V SSM3 AUDIO OUT kω L INA kω L INB SWA/SWB kω R INA kω R INB 7 SSM 8 SW 3 SW SW SW3 9 SW 9 SW 3 SW3 8 SW k Ω L OUT SSM3 kω R OUT SSM3 C /9 V 8V Figure 3. Virtual Ground Switching Figure. Double-Pole, Double-Throw Stereo Switch Using Virtual Ground Operation OUTLINE DIMENSIONS Dimensions shown in inches and (mm). Mini-DIP (P Suffix) Figure. Virtual Ground Switch THD+N vs. Frequency (V S = ± V, V A = V rms, with 8 khz Filter) PIN. (.33) MAX. (.). (3.8). (.8). (.3). (.9).9 (3.). (.) BSC.8 (7.). (.). (.). (.38). (3.8) MIN.7 (.77) SEATING. (.) PLANE.3 (8.).3 (7.). (.38).8 (.).9 (.9). (.93) SOIC (S Suffix) PIN.8 (3.).9 (.).99 (7.).9 (7.).93 (.).3937 (.) PRINTED IN U.S.A.. (.7) BSC.3 (.).9 (.3).9 (.7).98 (.) X - 8 Figure. Virtual Ground Switch Headroom (V S = ± V for SSM; V S = ±8 V for Op Amp, f = khz, with 8 khz Filter).8 (.3). (.).9 (.9).38 (.3). (.3).9 (.3). (.7).7 (.) 8
Dual Audio Analog Switches SSM2402/SSM2412
a FEATURES Clickless Bilateral Audio Switching Guaranteed Break-Before-Make Switching Low Distortion: 0.003% typ Low Noise: 1 nv/ Hz Superb OFF-Isolation: 120 db typ Low ON-Resistance: 60 typ Wide Signal
More informationQuad SPST JFET Analog Switch SW06
a FEATURES Two Normally Open and Two Normally Closed SPST Switches with Disable Switches Can Be Easily Configured as a Dual SPDT or a DPDT Highly Resistant to Static Discharge Destruction Higher Resistance
More informationOBSOLETE. Low Cost Quad Voltage Controlled Amplifier SSM2164 REV. 0
a FEATURES Four High Performance VCAs in a Single Package.2% THD No External Trimming 12 db Gain Range.7 db Gain Matching (Unity Gain) Class A or AB Operation APPLICATIONS Remote, Automatic, or Computer
More informationHigh Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection
a FEATURES High Common-Mode Rejection DC: 100 db typ 60 Hz: 100 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.001% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements
More informationQuad Current Controlled Amplifier SSM2024
a Quad Current Controlled Amplifier FEATURES Four VCAs in One Package Ground Referenced Current Control Inputs 82 db S/N at 0.3% THD Full Class A Operation 40 db Control Feedthrough (Untrimmed) Easy Signal
More information6 db Differential Line Receiver
a FEATURES High Common-Mode Rejection DC: 9 db typ Hz: 9 db typ khz: 8 db typ Ultralow THD:.% typ @ khz Fast Slew Rate: V/ s typ Wide Bandwidth: 7 MHz typ (G = /) Two Gain Levels Available: G = / or Low
More informationImproved Second Source to the EL2020 ADEL2020
Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling
More informationOBSOLETE. Self-Contained Audio Preamplifier SSM2017 REV. B
a FEATURES Excellent Noise Performance: 950 pv/ Hz or 1.5 db Noise Figure Ultralow THD: < 0.01% @ G = 100 Over the Full Audio Band Wide Bandwidth: 1 MHz @ G = 100 High Slew Rate: 17 V/ s typ Unity Gain
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load
More informationHigh Accuracy 8-Pin Instrumentation Amplifier AMP02
a FEATURES Low Offset Voltage: 100 V max Low Drift: 2 V/ C max Wide Gain Range 1 to 10,000 High Common-Mode Rejection: 115 db min High Bandwidth (G = 1000): 200 khz typ Gain Equation Accuracy: 0.5% max
More informationSingle Supply, Rail to Rail Low Power FET-Input Op Amp AD820
a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive
More informationOctal Sample-and-Hold with Multiplexed Input SMP18
a FEATURES High Speed Version of SMP Internal Hold Capacitors Low Droop Rate TTL/CMOS Compatible Logic Inputs Single or Dual Supply Operation Break-Before-Make Channel Addressing Compatible With CD Pinout
More informationVery Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION
Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8273 FEATURES ±4 V HBM ESD Very low distortion.25% THD + N (2 khz).15% THD + N (1 khz) Drives 6 Ω loads Two gain settings Gain of
More informationPrecision, Low Power, Micropower Dual Operational Amplifier OP290
Precision, Low Power, Micropower Dual Operational Amplifier OP9 FEATURES Single-/dual-supply operation:. V to 3 V, ±.8 V to ±8 V True single-supply operation; input and output voltage Input/output ranges
More informationLow Cost, General Purpose High Speed JFET Amplifier AD825
a FEATURES High Speed 41 MHz, 3 db Bandwidth 125 V/ s Slew Rate 8 ns Settling Time Input Bias Current of 2 pa and Noise Current of 1 fa/ Hz Input Voltage Noise of 12 nv/ Hz Fully Specified Power Supplies:
More information150 μv Maximum Offset Voltage Op Amp OP07D
5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply
More informationSelf-Contained Audio Preamplifier SSM2019
a FEATURES Excellent Noise Performance:. nv/ Hz or.5 db Noise Figure Ultra-low THD:
More informationLow Power. Video Op Amp with Disable AD810 REV. A. Closed-Loop Gain and Phase vs. Frequency, G = +2, R L = 150, R F = 715 Ω
CLOSED-LOOP db SHIFT Degrees DIFFERENTIAL % DIFFERENTIAL Degrees a FEATURES High Speed MHz Bandwidth ( db, G = +) MHz Bandwidth ( db, G = +) V/ s Slew Rate ns Settling Time to.% ( = V Step) Ideal for Video
More informationSingle Supply, Low Power, Triple Video Amplifier AD8013
a FEATURES Three Video Amplifiers in One Package Drives Large Capacitive Load Excellent Video Specifications (R L = 5 ) Gain Flatness. db to MHz.% Differential Gain Error. Differential Phase Error Low
More informationDual, Current Feedback Low Power Op Amp AD812
a FEATURES Two Video Amplifiers in One -Lead SOIC Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = ): Gain Flatness. db to MHz.% Differential Gain Error. Differential
More informationDual Picoampere Input Current Bipolar Op Amp AD706
a FEATURE HIGH DC PRECISION V max Offset Voltage.6 V/ C max Offset Drift pa max Input Bias Current LOW NOISE. V p-p Voltage Noise,. Hz to Hz LOW POWER A Supply Current Available in -Lead Plastic Mini-DlP,
More informationDual Low Power Operational Amplifier, Single or Dual Supply OP221
a FEATURES Excellent TCV OS Match, 2 V/ C Max Low Input Offset Voltage, 15 V Max Low Supply Current, 55 A Max Single Supply Operation, 5 V to 3 V Low Input Offset Voltage Drift,.75 V/ C High Open-Loop
More informationQuad Matched 741-Type Operational Amplifiers OP11
a FEATURES Guaranteed V OS : 5 V Max Guaranteed Matched CMRR: 94 db Min Guaranteed Matched V OS : 75 V Max LM148/LM348 Direct Replacement Low Noise Silicon-Nitride Passivation Internal Frequency Compensation
More informationMatched Monolithic Quad Transistor MAT04
a FEATURES Low Offset Voltage: 200 V max High Current Gain: 400 min Excellent Current Gain Match: 2% max Low Noise Voltage at 100 Hz, 1 ma: 2.5 nv/ Hz max Excellent Log Conformance: rbe = 0.6 max Matching
More informationADG1411/ADG1412/ADG1413
.5 Ω On Resistance, ±5 V/+2 V/±5 V, icmos, Quad SPST Switches ADG4/ADG42/ADG43 FEATURES.5 Ω on resistance.3 Ω on-resistance flatness. Ω on-resistance match between channels Continuous current per channel
More informationPrecision Micropower Single Supply Operational Amplifier OP777
a FEATURES Low Offset Voltage: 1 V Max Low Input Bias Current: 1 na Max Single-Supply Operation: 2.7 V to 3 V Dual-Supply Operation: 1.35 V to 15 V Low Supply Current: 27 A/Amp Unity Gain Stable No Phase
More informationAD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES
Preliminary Technical Data 0 MHz, 20 V/μs, G =, 0, 00, 000 i CMOS Programmable Gain Instrumentation Amplifier FEATURES Small package: 0-lead MSOP Programmable gains:, 0, 00, 000 Digital or pin-programmable
More informationVery Low Distortion, Precision Difference Amplifier AD8274
Very Low Distortion, Precision Difference Amplifier AD8274 FEATURES Very low distortion.2% THD + N (2 khz).% THD + N ( khz) Drives Ω loads Excellent gain accuracy.3% maximum gain error 2 ppm/ C maximum
More informationOBSOLETE. Parameter AD9621 AD9622 AD9623 AD9624 Units
a FEATURES MHz Small Signal Bandwidth MHz Large Signal BW ( V p-p) High Slew Rate: V/ s Low Distortion: db @ MHz Fast Settling: ns to.%. nv/ Hz Spectral Noise Density V Supply Operation Wideband Voltage
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationDual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP
Dual Precision, Low Cost, High Speed BiFET Op Amp FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +125 C) Controlled manufacturing baseline One
More informationSingle-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820
Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5
More informationHigh Common-Mode Voltage Difference Amplifier AD629
a FEATURES Improved Replacement for: INAP and INAKU V Common-Mode Voltage Range Input Protection to: V Common Mode V Differential Wide Power Supply Range (. V to V) V Output Swing on V Supply ma Max Power
More informationDual, Ultralow Distortion, Ultralow Noise Op Amp AD8599
Dual, Ultralow Distortion, Ultralow Noise Op Amp FEATURES Low noise: 1 nv/ Hz at 1 khz Low distortion: 5 db THD @ khz
More information200 ma Output Current High-Speed Amplifier AD8010
a FEATURES 2 ma of Output Current 9 Load SFDR 54 dbc @ MHz Differential Gain Error.4%, f = 4.43 MHz Differential Phase Error.6, f = 4.43 MHz Maintains Video Specifications Driving Eight Parallel 75 Loads.2%
More information0.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854
.5 Ω CMOS, 1.8 V to 5.5 V, Dual SPDT/2:1 Mux, Mini LFCSP ADG854 FEATURES.8 Ω typical on resistance Less than 1 Ω maximum on resistance at 85 C 1.8 V to 5.5 V single supply High current carrying capability:
More information15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP
5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline
More informationOBSOLETE TTL/CMOS INPUTS* TTL/CMOS OUTPUTS TTL/CMOS TTL/CMOS OUTPUTS DO NOT MAKE CONNECTIONS TO THESE PINS INTERNAL 10V POWER SUPPLY
a FEATURES kb Transmission Rate ADM: Small (. F) Charge Pump Capacitors ADM3: No External Capacitors Required Single V Power Supply Meets EIA-3-E and V. Specifications Two Drivers and Two Receivers On-Board
More informationDual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature
Data Sheet Dual Picoampere Input Current Bipolar Op Amp Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by
More informationUltrafast TTL Comparators AD9696/AD9698
a FEATURES 4.5 ns Propagation Delay 200 ps Maximum Propagation Delay Dispersion Single +5 V or 5 V Supply Operation Complementary Matched TTL Outputs APPLICATIONS High Speed Line Receivers Peak Detectors
More informationDual Picoampere Input Current Bipolar Op Amp AD706
Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available
More informationSingle Supply, Low Power Triple Video Amplifier AD813
a FEATURES Low Cost Three Video Amplifiers in One Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = 15 ) Gain Flatness.1 db to 5 MHz.3% Differential Gain Error.6
More informationPrecision, Low Power, Micropower Dual Operational Amplifier OP290
a FEATURES Single-/Dual-Supply Operation, 1. V to 3 V,. V to 1 V True Single-Supply Operation; Input and Output Voltage Ranges Include Ground Low Supply Current (Per Amplifier), A Max High Output Drive,
More informationLC 2 MOS Precision 5 V Quad SPST Switches ADG661/ADG662/ADG663
a FEATURE +5 V, 5 V Power upplies Ultralow Power issipation (
More informationUltrafast Comparators AD96685/AD96687
a FEATURES Fast: 2.5 ns Propagation Delay Low Power: 118 mw per Comparator Packages: DIP, SOIC, PLCC Power Supplies: +5 V, 5.2 V Logic Compatibility: ECL 50 ps Delay Dispersion APPLICATIONS High Speed
More informationOP SPECIFICATIONS ELECTRICAL CHARACTERISTICS (V S = ± V, T A = C, unless otherwise noted.) OPA/E OPF OPG Parameter Symbol Conditions Min Typ Max Min T
a FEATURES Excellent Speed:. V/ms Typ Fast Settling (.%): ms Typ Unity-Gain Stable High-Gain Bandwidth: MHz Typ Low Input Offset Voltage: mv Max Low Offset Voltage Drift: mv/ C Max High Gain: V/mV Min
More informationOBSOLETE. High-Speed, Dual Operational Amplifier OP271 REV. A. Figure 1. Simplified Schematic (One of the two amplifiers is shown.
a FEATURES Excellent Speed:. V/ms Typ Fast Settling (.%): ms Typ Unity-Gain Stable High-Gain Bandwidth: MHz Typ Low Input Offset Voltage: mv Max Low Offset Voltage Drift: mv/ C Max High Gain: V/mV Min
More informationHI-201HS. Features. High Speed, Quad SPST, CMOS Analog Switch. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) FN3123.
HI-HS Data Sheet September 4 FN.4 High Speed, Quad SPST, CMOS Analog Switch The HI-HS is a monolithic CMOS Analog Switch featuring very fast switching speeds and low ON resistance. The integrated circuit
More informationLC 2 MOS 5 Ω RON SPST Switches ADG451/ADG452/ADG453
LC 2 MOS 5 Ω RON SPST Switches ADG45/ADG452/ADG453 FEATURES Low on resistance (4 Ω) On resistance flatness (0.2 Ω) 44 V supply maximum ratings ±5 V analog signal range Fully specified at ±5 V, 2 V, ±5
More informationUltraprecision, 36 V, 2.8 nv/ Hz Dual Rail-to-Rail Output Op Amp AD8676
FEATURES Very low voltage noise 2.8 nv/ Hz @ khz Rail-to-rail output swing Low input bias current: 2 na maximum Very low offset voltage: 2 μv typical Low input offset drift:.6 μv/ C maximum Very high gain:
More informationAD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo
FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain
More informationHigh Speed, Low Power Dual Op Amp AD827
a FEATURES HIGH SPEED 50 MHz Unity Gain Stable Operation 300 V/ s Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads EXCELLENT VIDEO PERFORMANCE 0.04% Differential Gain @ 4.4 MHz 0.19 Differential
More informationSingle Channel Protector in an SOT-23 Package ADG465
a Single Channel Protector in an SOT-23 Package FEATURES Fault and Overvoltage Protection up to 40 V Signal Paths Open Circuit with Power Off Signal Path Resistance of R ON with Power On 44 V Supply Maximum
More informationLow Power, Rail-to-Rail Output, Precision JFET Amplifiers AD8641/AD8642/AD8643
Data Sheet Low Power, Rail-to-Rail Output, Precision JFET Amplifiers AD864/AD8642/AD8643 FEATURES Low supply current: 25 μa max Very low input bias current: pa max Low offset voltage: 75 μv max Single-supply
More informationTABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... 2 Specifications... 3 Absolute Maximum
FEATURES Offset voltage: 2.5 mv maximum Single-supply operation: 2.7 V to 5.5 V Low noise: 8 nv/ Hz Wide bandwidth: 24 MHz Slew rate: V/μs Short-circuit output current: 2 ma No phase reversal Low input
More informationHigh Speed, Low Power Dual Op Amp AD827
a FEATURES High Speed 50 MHz Unity Gain Stable Operation 300 V/ms Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads Excellent Video Performance 0.04% Differential Gain @ 4.4 MHz 0.198 Differential
More informationSingle-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822
Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp FEATURES True Single-Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single-Supply Capability from 3 V to 36
More informationQuad Picoampere Input Current Bipolar Op Amp AD704
a FEATURES High DC Precision 75 V Max Offset Voltage V/ C Max Offset Voltage Drift 5 pa Max Input Bias Current.2 pa/ C Typical I B Drift Low Noise.5 V p-p Typical Noise,. Hz to Hz Low Power 6 A Max Supply
More informationWideband, High Output Current, Fast Settling Op Amp AD842
a FEATURES AC PERFORMAE Gain Bandwidth Product: 8 MHz (Gain = 2) Fast Settling: ns to.1% for a V Step Slew Rate: 375 V/ s Stable at Gains of 2 or Greater Full Power Bandwidth: 6. MHz for V p-p DC PERFORMAE
More informationQuad 12-Bit Digital-to-Analog Converter (Serial Interface)
Quad 1-Bit Digital-to-Analog Converter (Serial Interface) FEATURES COMPLETE QUAD DAC INCLUDES INTERNAL REFERENCES AND OUTPUT AMPLIFIERS GUARANTEED SPECIFICATIONS OVER TEMPERATURE GUARANTEED MONOTONIC OVER
More informationFour-Channel Sample-and-Hold Amplifier AD684
a FEATURES Four Matched Sample-and-Hold Amplifiers Independent Inputs, Outputs and Control Pins 500 ns Hold Mode Settling 1 s Maximum Acquisition Time to 0.01% Low Droop Rate: 0.01 V/ s Internal Hold Capacitors
More informationHI-201HS. High Speed Quad SPST CMOS Analog Switch
SEMICONDUCTOR HI-HS December 99 Features Fast Switching Times, N = ns, FF = ns Low ON Resistance of Ω Pin Compatible with Standard HI- Wide Analog Voltage Range (±V Supplies) of ±V Low Charge Injection
More informationPrecision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD8512
a FEATURES Fast Settling Time: 5 ns to.% Low Offset Voltage: V Max Low TcVos: V/ C Typ Low Input Bias Current: 25 pa Typ Dual-Supply Operation: 5 V to 5 V Low Noise: 8 nv/ Hz Low Distortion:.5% No Phase
More informationHigh Common-Mode Voltage, Programmable Gain Difference Amplifier AD628
High Common-Mode Voltage, Programmable Gain Difference Amplifier AD628 FEATURES FUNCTIONAL BLOCK DIAGRAM High common-mode input voltage range ±20 V at VS = ±5 V Gain range 0. to 00 Operating temperature
More informationCMOS 12-Bit Serial Input Multiplying DIGITAL-TO-ANALOG CONVERTER
CMOS 12-Bit Serial Input Multiplying DIGITAL-TO-ANALOG CONVERTER FEATURES 12-BICCURACY IN 8-PIN MINI-DIP AND 8-PIN SOIC FAST 3-WIRE SERIAL INTERFACE LOW INL AND DNL: ±1/2 LSB max GAIN ACCURACY TO ±1LSB
More informationDATASHEET HI-201HS. Features. Applications. Ordering Information. Pinout (Switches Shown For Logic 1 Input) High Speed, Quad SPST, CMOS Analog Switch
DATASHEET HI-21HS High Speed, Quad SPST, CMOS Analog Switch The HI-21HS is a monolithic CMOS Analog Switch featuring very fast switching speeds and low ON resistance. The integrated circuit consists of
More informationQuad Picoampere Input Current Bipolar Op Amp AD704
a FEATURES High DC Precision 75 V Max Offset Voltage V/ C Max Offset Voltage Drift 5 pa Max Input Bias Current.2 pa/ C Typical I B Drift Low Noise.5 V p-p Typical Noise,. Hz to Hz Low Power 6 A Max Supply
More informationAD9300 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 12 V 5%; C L = 10 pf; R L = 2 k, unless otherwise noted) COMMERCIAL 0 C to +70 C Test AD9300K
a FEATURES 34 MHz Full Power Bandwidth 0.1 db Gain Flatness to 8 MHz 72 db Crosstalk Rejection @ 10 MHz 0.03 /0.01% Differential Phase/Gain Cascadable for Switch Matrices MIL-STD-883 Compliant Versions
More informationLow Capacitance, Low Charge Injection, ±15 V/+12 V icmos Dual SPST Switches ADG1221/ADG1222/ADG1223
Data Sheet Low Capacitance, Low Charge Injection, ±15 V/+12 V icmos Dual SPST Switches ADG1221/ADG1222/ADG1223 FEATURES
More informationSingle and Dual, Ultralow Distortion, Ultralow Noise Op Amps AD8597/AD8599 PIN CONFIGURATIONS FEATURES APPLICATIONS
Single and Dual, Ultralow Distortion, Ultralow Noise Op Amps FEATURES Low noise:. nv/ Hz at khz Low distortion: db THD @ khz Input noise,. Hz to Hz:
More informationQuad 7 ns Single Supply Comparator AD8564
Quad 7 ns Single Supply Comparator AD8564 FEATURES 5 V single-supply operation 7 ns propagation delay Low power Separate input and output sections TTL/CMOS logic-compatible outputs Wide output swing TSSOP,
More informationHigh Speed, +5 V, 0.1 F CMOS RS-232 Driver/Receivers ADM202/ADM203
a FEATURES kb Transmission Rate ADM: Small (. F) Charge Pump Capacitors ADM: No External Capacitors Required Single V Power Supply Meets EIA--E and V. Specifications Two Drivers and Two Receivers On-Board
More informationOBSOLETE. Microphone Preamplifier with Variable Compression and Noise Gating SSM2165
a FEATURES Complete Microphone Conditioner in an 8-Lead Package Single +5 V Operation Preset Noise Gate Threshold Compression Ratio Set by External Resistor Automatic Limiting Feature Prevents ADC Overload
More informationUltraprecision Operational Amplifier OP177
Ultraprecision Operational Amplifier FEATURES Ultralow offset voltage TA = 25 C, 25 μv maximum Outstanding offset voltage drift 0. μv/ C maximum Excellent open-loop gain and gain linearity 2 V/μV typical
More informationLF353 Wide Bandwidth Dual JFET Input Operational Amplifier
LF353 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage
More information5V Capable Low-Voltage DPDT Analog Switch
5V Capable Low-Voltage DPDT Analog Switch General Description is a 5V high quality low-voltage double-pole double-throw (DPDT) analog switch. supply voltage is designed to operate from 2.5V to 5.5V. Supply
More informationQuad Picoampere Input Current Bipolar Op Amp AD704
a FEATURES High DC Precision 75 V max Offset Voltage V/ C max Offset Voltage Drift 5 pa max Input Bias Current.2 pa/ C typical I B Drift Low Noise.5 V p-p typical Noise,. Hz to Hz Low Power 6 A max Supply
More informationDG200, DG201. CMOS Dual/Quad SPST Analog Switches. Description. Features. Ordering Information. Applications. Pinouts.
SEMICONDUCTOR DG200, DG20 December 993 CMOS Dual/Quad SPST Analog Switches Features Switches Greater than 28V P-P Signals with ±5 Supplies Break-Before-Make Switching t OFF 250ns, t ON 700ns Typical TTL,
More informationOctal, RS-232/RS-423 Line Driver ADM5170
a FEATURES Eight Single Ended Line Drivers in One Package Meets EIA Standard RS-3E, RS-3A and CCITT V./X. Resistor Programmable Slew Rate Wide Supply Voltage Range Low Power CMOS 3-State Outputs TTL/CMOS
More informationHigh Speed FET-INPUT OPERATIONAL AMPLIFIERS
OPA OPA OPA OPA OPA OPA OPA OPA OPA High Speed FET-INPUT OPERATIONAL AMPLIFIERS FEATURES FET INPUT: I B = 5pA max WIDE BANDWIDTH: MHz HIGH SLEW RATE: V/µs LOW NOISE: nv/ Hz (khz) LOW DISTORTION:.% HIGH
More informationDual/Quad Low Power, High Speed JFET Operational Amplifiers OP282/OP482
Dual/Quad Low Power, High Speed JFET Operational Amplifiers OP22/OP42 FEATURES High slew rate: 9 V/µs Wide bandwidth: 4 MHz Low supply current: 2 µa/amplifier max Low offset voltage: 3 mv max Low bias
More informationADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe
NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time
More informationPrecision, 16 MHz CBFET Op Amp AD845
a FEATURES Replaces Hybrid Amplifiers in Many Applications AC PERFORMANCE: Settles to 0.01% in 350 ns 100 V/ s Slew Rate 12.8 MHz Min Unity Gain Bandwidth 1.75 MHz Full Power Bandwidth at 20 V p-p DC PERFORMANCE:
More informationQuad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
19-2418; Rev ; 4/2 Quad, Rail-to-Rail, Fault-Protected, General Description The are quad, single-pole/single-throw (SPST), fault-protected analog switches. They are pin compatible with the industry-standard
More informationRail-to-Rail, High Output Current Amplifier AD8397
Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear
More information2 REV. C. THERMAL CHARACTERISTICS H-10A: θ JC = 25 C/W; θ JA = 150 C/W E-20A: θ JC = 22 C/W; θ JA = 85 C/W D-14: θ JC = 22 C/W; θ JA = 85 C/W
a FEATURES Pretrimmed to.0% (AD53K) No External Components Required Guaranteed.0% max 4-Quadrant Error (AD53K) Diff Inputs for ( ) ( Y )/ V Transfer Function Monolithic Construction, Low Cost APPLICATIONS
More informationHigh Voltage, Low Noise, Low Distortion, Unity-Gain Stable, High Speed Op Amp ADA4898-1/ADA4898-2
FEATURES Ultralow noise.9 nv/ Hz.4 pa/ Hz. nv/ Hz at Hz Ultralow distortion: 93 dbc at 5 khz Wide supply voltage range: ±5 V to ±6 V High speed 3 db bandwidth: 65 MHz (G = +) Slew rate: 55 V/µs Unity gain
More informationDual FET-Input, Low Distortion OPERATIONAL AMPLIFIER
www.burr-brown.com/databook/.html Dual FET-Input, Low Distortion OPERATIONAL AMPLIFIER FEATURES LOW DISTORTION:.3% at khz LOW NOISE: nv/ Hz HIGH SLEW RATE: 25V/µs WIDE GAIN-BANDWIDTH: MHz UNITY-GAIN STABLE
More informationPrecision, Very Low Noise, Low Input Bias Current, Wide Bandwidth JFET Operational Amplifiers AD8510/AD8512
a FEATURES Fast Settling Time: 5 ns to.1% Low Offset Voltage: V Max Low TcV OS : 1 V/ C Typ Low Input Bias Current: 25 pa Typ Dual-Supply Operation: 5 V to 15 V Low Noise: 8 nv/ Hz Low Distortion:.5% No
More informationUltralow Offset Voltage Operational Amplifier OP07
Ultralow Offset Voltage Operational Amplifier OP07 FEATURES Low VOS: 75 μv maximum Low VOS drift:.3 μv/ C maximum Ultrastable vs. time:.5 μv per month maximum Low noise: 0.6 μv p-p maximum Wide input voltage
More informationDual Low Offset, Low Power Operational Amplifier OP200
Dual Low Offset, Low Power Operational Amplifier OP200 FEATURES Low input offset voltage: 75 μv maximum Low offset voltage drift, over 55 C < TA < +25 C 0.5 μv/ C maximum Low supply current (per amplifier):
More informationInternally Trimmed Integrated Circuit Multiplier AD532
a Internally Trimmed Integrated Circuit Multiplier AD53 FEATURES PIN CONFIGURATIONS Pretrimmed to.0% (AD53K) Y No External Components Required Y V Guaranteed.0% max 4-Quadrant Error (AD53K) OS 4 +V S OUT
More informationQuad Low Offset, Low Power Operational Amplifier OP400
Quad Low Offset, Low Power Operational Amplifier OP4 FEATURES Low input offset voltage 5 μv max Low offset voltage drift over 55 C to 25 C,.2 pv/ C max Low supply current (per amplifier) 725 μa max High
More informationLM4752 Stereo 11W Audio Power Amplifier
LM4752 Stereo 11W Audio Power Amplifier General Description The LM4752 is a stereo audio amplifier capable of delivering 11W per channel of continuous average output power to a 4Ω load, or 7W per channel
More informationHA MHz, PRAM Four Channel Programmable Amplifiers. Features. Applications. Pinout. Ordering Information
HA0 Data Sheet August 00 FN89. 0MHz, PRAM Four Channel Programmable Amplifiers The HA0 comprise a series of fourchannel programmable amplifiers providing a level of versatility unsurpassed by any other
More informationHA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information
HA26, HA26 September 998 File Number 292.3 2MHz, High Input Impedance Operational Amplifiers HA26/26 are internally compensated bipolar operational amplifiers that feature very high input impedance (MΩ,
More informationHigh Speed, +5 V, 0.1 µf CMOS RS-232 Drivers/Receivers ADM222/ADM232A/ADM242*
a FEATURES 00 kb/s Transmission Rate Small (0. µf) Charge Pump Capacitors Single V Power Supply Meets All EIA--E and V. Specifications Two Drivers and Two Receivers On-Board DC-DC Converters ± V Output
More informationLow Cost, Precision JFET Input Operational Amplifiers ADA4000-1/ADA4000-2/ADA4000-4
Low Cost, Precision JFET Input Operational Amplifiers ADA-/ADA-/ADA- FEATURES High slew rate: V/μs Fast settling time Low offset voltage:.7 mv maximum Bias current: pa maximum ± V to ±8 V operation Low
More informationOBSOLETE. Ultrahigh Speed Window Comparator with Latch AD1317
a FEATURES Full Window Comparator 2.0 pf max Input Capacitance 9 V max Differential Input Voltage 2.5 ns Propagation Delays Low Dispersion Low Input Bias Current Independent Latch Function Input Inhibit
More informationDual, Low Power Video Op Amp AD828
a FEATURES Excellent Video Performance Differential Gain and Phase Error of.% and. High Speed MHz db Bandwidth (G = +) V/ s Slew Rate ns Settling Time to.% Low Power ma Max Power Supply Current High Output
More information