Low Power. Video Op Amp with Disable AD810 REV. A. Closed-Loop Gain and Phase vs. Frequency, G = +2, R L = 150, R F = 715 Ω

Size: px
Start display at page:

Download "Low Power. Video Op Amp with Disable AD810 REV. A. Closed-Loop Gain and Phase vs. Frequency, G = +2, R L = 150, R F = 715 Ω"

Transcription

1 CLOSED-LOOP db SHIFT Degrees DIFFERENTIAL % DIFFERENTIAL Degrees a FEATURES High Speed MHz Bandwidth ( db, G = +) MHz Bandwidth ( db, G = +) V/ s Slew Rate ns Settling Time to.% ( = V Step) Ideal for Video Applications MHz Bandwidth (. db, G = +).% Differential Gain. Differential Phase Low Noise.9 nv/ Hz Input Voltage Noise pa/ Hz Inverting Input Current Noise Low Power. ma Supply Current max. ma Supply Current (Power-Down Mode) High Performance Disable Function Turn-Off Time ns Break Before Make Guaranteed Input to Output Isolation of db (OFF State) Flexible Operation Specified for V and peration.9 utput Swing Into a Load (V S = V) APPLICATIONS Professional Video Cameras Multimedia Systems NTSC, PAL & SECAM Compatible Systems Video Line Driver ADC/DAC Buffer DC Restoration Circuits Low Power Video Op Amp with Disable AD CONNECTION DIAGRAM -Pin Plastic Mini-DIP (N), SOIC (R) and Cerdip (Q) Packages OFFSET NULL IN +IN AD TOP VIEW DISABLE OUTPUT OFFSET NULL PRODUCT DESCRIPTION The AD is a composite and HDTV compatible, current feedback, video operational amplifier, ideal for use in systems such as multimedia, digital tape recorders and video cameras. The. db flatness specification at bandwidth of MHz (G = +) and the differential gain and phase of.% and. (NTSC) make the AD ideal for any broadcast quality video system. All these specifications are under load conditions of Ω (one Ω back terminated cable). The AD is ideal for power sensitive applications such as video cameras, offering a low power supply current of. ma max. The disable feature reduces the power supply current to only. ma, while the amplifier is not in use, to conserve power. Furthermore the AD is specified over a power supply range of ± V to ± V. The AD works well as an ADC or DAC buffer in video systems due to its unity gain bandwidth of MHz. Because the AD is a transimpedance amplifier, this bandwidth can be maintained over a wide range of gains while featuring a low noise of.9 nv/ Hz for wide dynamic range applications... = + R L = Ω ±.V ±.V = + R F = R L = Ω f C =.MHz IRE MODULATED RAMP SUPPLY VOLTAGE ± Volts Closed-Loop Gain and Phase vs. Frequency, G = +, R L =, R F = Ω Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Differential Gain and Phase vs. Supply Voltage One Technology Way, P.O. Box 9, Norwood, MA -9, U.S.A. Tel: /9- Fax: /-

2 AD SPECIFICATIONS T A = + C and V S = V dc, R L = unless otherwise noted) ADA ADS Parameter Conditions V S Min Typ Max Min Typ Max Units DYNAMIC PERFORMANCE db Bandwidth (G = +) R FB = ± V MHz (G = +) R FB = ± V MHz (G = +) R FB = ± V MHz (G = +) R FB = ± V MHz. db Bandwidth (G = +) R FB = ± V MHz Full Power Bandwidth (G = +) R FB = ± V MHz = V p-p, R L = Ω ± V MHz Slew Rate R L = Ω ± V V/µs R L = Ω ± V V/µs Settling Time to.% V Step, G = ± V ns Settling Time to.% V Step, G = ± V ns Differential Gain f =. MHz ± V.... % f -. MHz ± V.... % Differential Phase f =. MHz ± V.... Degrees f =. MHz ± V.... Degrees Total Harmonic Distortion f = MHz, = V p-p R L = Ω, G = + ± V dbc INPUT OFFSET VOLTAGE ± V, ± V.. mv T MIN T MAX ± V, ± V. mv Offset Voltage Drift µv/ C INPUT BIAS CURRENT Input T MIN T MAX ± V, ± V.. µa +Input T MIN T MAX ± V, ± V. µa OPEN-LOOP T MIN T MAX TRANSRESISTANCE = ± V, R L = Ω ± V.... MΩ = ±. V, R L = Ω ± V.... MΩ OPEN-LOOP T MIN T MAX DC VOLTAGE = ± V, R L = Ω ± V db = ±. V, R L = Ω ± V db COMMON-MODE REJECTION T MIN T MAX S V CM = ± V ± V db V CM = ±. V ± V db ±Input Current T MIN T MAX ± V, ± V.... µa/v POWER SUPPLY REJECTION ±. V to ± V S T MIN T MAX db ± Input Current T MIN T MAX.... µa/v INPUT VOLTAGE NOISE f = khz ± V, ± V.9.9 nv/ Hz INPUT CURRENT NOISE I IN, f = khz ± V, ± V pa/ Hz +I IN, f = khz ± V, ± V.. pa/ Hz INPUT COMMON-MODE ± V ±. ±. ±. ± V VOLTAGE RANGE ± V ± ± ± ± V OUTPUT CHARACTERISTICS Output Voltage Swing R L = Ω, T MIN T MAX ± V ±. ±.9 ±. ±.9 V R L = Ω ± V ±. ±.9 ±. ±.9 V R L = Ω, T MIN T MAX ± V ± ± V Short-Circuit Current ± V ma Output Current T MIN T MAX ± V, ± V ma OUTPUT RESISTANCE Open Loop ( MHz) Ω INPUT CHARACTERISTICS Input Resistance +Input ± V.. MΩ Input ± V Ω Input Capacitance +Input ± V pf DISABLE CHARACTERISTICS OFF Isolation f = MHz, See Figure db OFF Output Impedance See Figure (R F + R G ) pf (R F + R G ) pf

3 TOTAL POWER DISSIPATION Watts AD ADA ADS Parameter Conditions V S Min Typ Max Min Typ Max Units Turn On Time Z OUT = Low, See Figure ns Turn Off Time Z OUT = High ns Disable Pin Current Disable Pin = V ± V µa ± V 9 9 µa Min Disable Pin Current to Disable T MIN T MAX ± V, ± V µa POWER SUPPLY Operating Range + C to T MAX ±. ± ±. ± V T MIN ±. ± ±. ± V Quiescent Current ± V.... ma ± V.... ma T MIN T MAX ± V, ± V.. 9. ma Power-Down Current ± V.... ma ± V.... ma NOTES See Analog Devices Military Data Sheet for B Specifications. Slew rate measurement is based on % to 9% rise time with the amplifier configured for a gain of. Voltage Swing is defined as useful operating range, not the saturation range. Disable guaranteed break before make. Turn On Time is defined with ± V supplies using complementary output CMOS to drive the disable pin. Specifications subject to change without notice. ABSOLUTE MAXIMUM RATINGS Supply Voltage ± V Internal Power Dissipation Observe Derating Curves Output Short Circuit Duration.... Observe Derating Curves Common-Mode Input Voltage ±V S Differential Input Voltage ± V Storage Temperature Range Plastic DIP C to + C Cerdip C to + C Small Outline IC C to + C Operating Temperature Range ADA C to + C ADS C to + C Lead Temperature Range (Soldering sec) C NOTES Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum raring conditions for extended periods may affect device reliability. -Pin Plastic Package: θ JA = 9 C/Watt; -Pin Cerdip Package: θ JA = C/Watt; -Pin SOIC Package: θ JA = C/Watt. ESD SUSCEPTIBILITY ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as volts, which readily accumulate on the human body and on test equipment, can discharge without detection. Although the AD features ESD protection circuitry, permanent damage may still occur on these devices if they are subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid any performance degradation or loss of functionality. ORDERING GUIDE Temperature Package Package Model Range Description Option ADAN C to + C -Pin Plastic DIP N- ADAR C to + C -Pin Plastic SOIC R- ADAR-REEL C to + C -Pin Plastic SOIC R- 9-9MPA C to + C -Pin Cerdip Q- MAXIMUM POWER DISSIPATION The maximum power that can be safely dissipated by the AD is limited by the associated rise in junction temperature. For the plastic packages, the maximum safe junction temperature is C. For the cerdip package, the maximum junction temperature is C. If these maximums are exceeded momentarily, proper circuit operation will be restored as soon as the die temperature is reduced. Leaving the device in the overheated condition for an extended period can result in device burnout. To ensure proper operation, it is important to observe the derating curves PIN SOIC -PIN MINI-DIP -PIN CERDIP AMBIENT TEMPERATURE C -PIN MINI-DIP Maximum Power Dissipation vs. Temperature While the AD is internally short circuit protected, this may not be sufficient to guarantee that the maximum junction temperature is not exceeded under all conditions..µf kω AD.µF SEE TEXT Offset Null Configuration

4 INPUT BIAS CURRENT µa INPUT OFFSET VOLTAGE mv OUTPUT VOLTAGE Volts p-p SUPPLY CURRENT ma MAGNITUDE OF THE OUTPUT VOLTAGE ±Volts MAGNITUDE OF THE OUTPUT VOLTAGE ±Volts AD Typical Characteristics NO LOAD NO LOAD R L = Ω R L = Ω Figure. Input Common-Mode Voltage Range vs. Supply Voltage Figure. Output Voltage Swing vs. Supply ±V SUPPLY 9 V S = SUPPLY k k LOAD RESISTANCE Ohms Figure. Output Voltage Swing vs. Load Resistance JUNCTION TEMPERATURE C Figure. Supply Current vs. Junction Temperature NONINVERTING INPUT V S =, ±V V S = INVERTING INPUT V S =, ±V JUNCTION TEMPERATURE C Figure. Input Bias Current vs. Temperature JUNCTION TEMPERATURE C Figure. Input Offset Voltage vs. Junction Temperature

5 OUTPUT VOLTAGE Volts p-p VOLTAGE NOISE nv/ Hz CURRENT NOISE pa/ Hz CLOSED-LOOP OUTPUT RESISTANCE Ω OUTPUT RESISTANCE Ω SHORT CIRCUIT CURRENT ma OUTPUT CURRENT ma Typical Characteristics AD V S = ± V V S = ± V V S = JUNCTION TEMPERATURE C Figure. Short Circuit Current vs. Temperature JUNCTION TEMPERATURE C Figure. Linear Output Current vs. Temperature. M. = R F = V S = k k. k. k k M M M Figure 9. Closed-Loop Output Resistance vs. Frequency k M M M Figure. Output Resistance vs. Frequency, Disabled State ± OUTPUT LEVEL FOR % THD R L = Ω V S = TO ±V INVERTING INPUT CURRENT NOISE V S = VOLTAGE NOISE NONINVERTING INPUT CURRENT NOISE k M M M Figure. Large Signal Frequency Response k k k Figure. Input Voltage and Current Noise vs. Frequency

6 OUTPUT SWING FROM ±V TO V SLEW RATE V/µs HARMONIC DISTORTION dbc HARMONIC DISTORTION dbc COMMON-MODE REJECTION db POWER SUPPLY REJECTION db AD Typical Characteristics 9 R F = A V = + V S = CURVES ARE FOR WORST CASE CONDITION WHERE ONE SUPPLY IS VARIED WHILE THE OTHER IS HELD CONSTANT k k M M M Figure. Common-Mode Rejection vs. Frequency k k M M M Figure. Power Supply Rejection vs. Frequency = V p-p R L = Ω = + V S = ±V SUPPLIES = + R L = Ω nd HARMONIC rd HARMONIC UT = V p-p nd HARMONIC nd rd rd HARMONIC nd rd UT = V p-p k k k M M Figure. Harmonic Distortion vs. Frequency (R L = Ω) k k k M M Figure. Harmonic Distortion vs. Frequency (R L = Ω).% R L = Ω.% R F = R G = kω R L = Ω = = +.%.% = + SETTLING TIME ns Figure. Output Swing and Error vs. Settling Time Figure. Slew Rate vs. Supply Voltage

7 db BANDWIDTH MHz db BANDWIDTH MHz CLOSED-LOOP db CLOSED-LOOP db SHIFT Degrees SHIFT Degrees Typical Characteristics, Noninverting Connection AD R F V ns R G.µF TO TEKTRONIX P FET PROBE 9 AD HP PULSE GENERATOR Ω.µF R L % V Figure 9. Noninverting Amplifier Connection Figure. Small Signal Pulse Response, Gain = +, R F = kω, R L = Ω, V S = ± V = + R L = Ω 9 = + R L = kω 9 ±.V ±.V Figure. Closed-Loop Gain and Phase vs. Frequency, G= +. R F = kω for ± V, 9 Ω for ± V and ±. V ±.V ±.V Figure. Closed-Loop Gain and Phase vs. Frequency, G= +, R F = kω for ± V, 9 Ω for ± V and ±. V 9 G = + R L = Ω = mv p-p R F = PEAKING db G = + R L = kω = mv p-p PEAKING db R F = kω PEAKING. db R F = R F = kω PEAKING.dB R F =.kω R F =.kω Figure. Bandwidth vs. Supply Voltage, Gain = +, R L = Ω Figure. db Bandwidth vs. Supply Voltage G = +, R L = kω

8 db BANDWIDTH MHz db BANDWIDTH MHz CLOSED-LOOP db CLOSED-LOOP db SHIFT Degrees SHIFT Degrees AD Typical Characteristics, Noninverting Connection mv ns V ns 9 9 % % V V Figure. Small Signal Pulse Response, Gain = +, R F = Ω, R L = Ω, V S = ± V Figure. Large Signal Pulse Response, Gain = +, R F = Ω, R L = Ω, V S = ± V = + R F = Ω R L = Ω 9 = + R F = Ω R L = kω 9 9 ±.V ±.V Figure. Closed-Loop Gain and Phase vs. Frequency, G = +, R L = Ω 9 ±.V ±.V Figure. Closed-Loop Gain and Phase vs. Frequency, G = +, R L = kω 9 G = + R L = Ω = mv p-p 9 G = + R L = kω = m V p-p PEAKING.dB PEAKING.dB R F = Ω R F = Ω R F = Ω R F = kω PEAKING.dB R F = Ω R F = kω PEAKING.dB Figure 9. db Bandwidth vs. Supply Voltage, Gain = +, R L = Ω Figure. db Bandwidth vs. Supply Voltage, Gain = +, R L = kω

9 db BANDWIDTH MHz db BANDWIDTH MHz CLOSED-LOOP db CLOSED-LOOP db SHIFT Degrees SHIFT Degrees Typical Characteristics, Inverting Connection AD R F V ns.µf R G HP AD PULSE GENERATOR.µF TO TEKTRONIX P FET PROBE R L 9 % V Figure. Inverting Amplifier Connection Figure. Small Signal Pulse Response, Gain =, R F = Ω, R L = Ω, V S = ± V = R L = Ω 9 = R L = kω 9 ±.V 9 ±.V 9 ±.V ±.V Figure. Closed-Loop Gain and Phase vs. Frequency G =, R L = Ω, R F = Ω for ± V, Ω for ± V and ±. V Figure. Closed-Loop Gain and Phase vs. Frequency, G =, R L = kω, R F = Ω for V S = ± V, Ω for ± V and ±. V 9 G = R L = = mv p-p PEAKING.dB G = R L = kω = mv p-p R F = Ω PEAKING.dB R F = Ω PEAKING.dB R F = Ω R F = kω R F = 9Ω R F = kω PEAKING.dB Figure. db Bandwidth vs. Supply Voltage, Gain =, R L = Ω Figure. db Bandwidth vs. Supply Voltage, Gain =, R L = kω 9

10 db BANDWIDTH MHz db BANDWIDTH MHz CLOSED-LOOP db CLOSED-LOOP db SHIFT Degrees SHIFT Degrees AD Typical Characteristics, Inverting Connection mv ns V ns 9 9 % % V V Figure. Small Signal Pulse Response, Gain =, R F = Ω, R L = Ω, V S = ± V Figure. Large Signal Pulse Response, Gain =, R F = Ω, R L = Ω, V S = ± V = R F = 9Ω R L = Ω 9 = R F = 9Ω R L = kω 9 9 ±.V ±.V 9 Figure 9. Closed-Loop Gain and Phase vs. Frequency, G =, R L = Ω 9 ±.V ±.V Figure. Closed-Loop Gain and Phase vs. Frequency, G =, R L = kω 9 9 G = R L = Ω = mv p- p NO PEAKING 9 G = R L = kω = mv p- p NO PEAKING R F = 9Ω R F = 9Ω R F = R F = Ω R F = Ω R F = Figure. db Bandwidth vs. Supply Voltage, G =, R L = Ω Figure. db Bandwidth vs. Supply Voltage, G =, R L = kω

11 Applications AD GENERAL DESIGN CONSIDERATIONS The AD is a current feedback amplifier optimized for use in high performance video and data acquisition systems. Since it uses a current feedback architecture, its closed-loop bandwidth depends on the value of the feedback resistor. Table I below contains recommended resistor values for some useful closedloop gains and supply voltages. As you can see in the table, the closed-loop bandwidth is not a strong function of gain, as it would be for a voltage feedback amp. The recommended resistor values will result in maximum bandwidths with less than. db of peaking in the gain vs. frequency response. The db bandwidth is also somewhat dependent on the power supply voltage. Lowering the supplies increases the values of internal capacitances, reducing the bandwidth. To compensate for this, smaller values of feedback resistor are sometimes used at lower supply voltages. The characteristic curves illustrate that bandwidths of over MHz on V total and over MHz on V total supplies can be achieved. Table I. db Bandwidth vs. Closed-Loop Gain and Resistance Values (R L = ) V S = V Closed-Loop db BW Gain R FB R G (MHz) + kω + Ω Ω + Ω Ω Ω Ω 9 Ω.9 Ω V S = V Closed-Loop db BW Gain R FB R G (MHz) + 9 Ω + Ω Ω + Ω Ω Ω Ω 9 Ω.9 Ω ACHIEVING VERY FLAT RESPONSE AT HIGH FREQUENCY Achieving and maintaining gain flatness of better than. db above MHz is not difficult if the recommended resistor values are used. The following issues should be considered to ensure consistently excellent results. CHOICE OF FEEDBACK AND RESISTOR Because the db bandwidth depends on the feedback resistor, the fine scale flatness will, to some extent, vary with feedback resistor tolerance. It is recommended that resistors with a % tolerance be used if it is desired to maintain exceptional flatness over a wide range of production lots. PRINTED CIRCUIT BOARD LAYOUT As with all wideband amplifiers, PC board parasitics can affect the overall closed-loop performance. Most important are stray capacitances at the output and inverting input nodes. (An added capacitance of pf between the inverting input and ground will add about. db of peaking in the gain of response, and increase the bandwidth to MHz.) A space (/" is plenty) should be left around the signal lines to minimize coupling. Also, signal lines connecting the feedback and gain resistors should be short enough so that their associated inductance does not cause high frequency gain errors. Line lengths less than /" are recommended. QUALITY OF COAX CABLE Optimum flatness when driving a coax cable is possible only when the driven cable is terminated at each end with a resistor matching its characteristic impedance. If coax were ideal, then the resulting flatness would not be affected by the length of the cable. While outstanding results can be achieved using inexpensive cables, some variation in flatness due to varying cable lengths is to be expected. POWER SUPPLY BYPASSING Adequate power supply bypassing can be critical when optimizing the performance of a high frequency circuit. Inductance in the power supply leads can contribute to resonant circuits that produce peaking in the amplifier's response. In addition, if large current transients must be delivered to the load, then bypass capacitors (typically greater than µf) will be required to provide the best settling time and lowest distortion. Although the recommended. µf power supply bypass capacitors will be sufficient in most applications, more elaborate bypassing (such as using two paralleled capacitors) may be required in some cases. POWER SUPPLY OPERATING RANGE The AD will operate with supplies from ± V down to about ±. V. On ±. V the low distortion output voltage swing will be better than V peak to peak. Single supply operation can be realized with excellent results by arranging for the input common-mode voltage to be biased at the supply midpoint. OFFSET NULLING A kω pot connected between Pins and, with its wiper connected to V+, can be used to trim out the inverting input current (with about ± µa of range). For closed-loop gains above about, this may not be sufficient to trim the output offset voltage to zero. Tie the pot's wiper to ground through a large value resistor ( kω for ± V supplies, kω for ± V supplies) to trim the output to zero at high closed-loop gains.

12 CLOSED-LOOP db LOAD CAPACITANCE pf AD CAPACITIVE LOADS When used with the appropriate feedback resistor, the AD can drive capacitive loads exceeding pf directly without oscillation. By using the curves in Figure to chose the resistor value, less than db of peaking can easily be achieved without sacrificing much bandwidth. Note that the curves were generated for the case of a kω load resistor, for smaller load resistances, the peaking will be less than indicated by Figure. Another method of compensating for large load capacitances is to insert a resistor in series with the loop output as shown in Figure. In most cases, less than Ω is all that is needed to achieve an extremely flat gain response. Figures to illustrate the outstanding performance that can be achieved when driving a pf capacitor. k V S = k k FEEDBACK RESISTOR Ω = + R L = kω k R F.µF Figure. Max Load Capacitance for Less than db of Peaking vs. Feedback Resistor.µF R G AD.µF R S (OPTIONAL) C L R L 9 V ns R T.µF UT Figure. Circuit Options for Driving a Large Capacitive Load % V 9 G = + R L = kω C L = pf Figure. AD Driving a pf Load, Gain = +, R F = Ω, R S = Ω, R L = kω 9 R F =.kω R S = R F = R S = Ω Figure. Performance Comparison of Two Methods for Driving a Large Capacitive Load DISABLE MODE By pulling the voltage on Pin to common ( V), the AD can be put into a disabled state. In this condition, the supply current drops to less than. ma, the output becomes a high impedance, and there is a high level of isolation from input to output. In the case of a line driver for example, the output impedance will be about the same as for a. kω resistor (the feedback plus gain resistors) in parallel with a pf capacitor (due to the output) and the input to output isolation will be better than db at MHz. Leaving the disable pin disconnected (floating) will leave the AD operational in the enabled state. In cases where the amplifier is driving a high impedance load, the input to output isolation will decrease significantly if the input signal is greater than about. V peak to peak. The isolation can be restored back to the db level by adding a dummy load (say Ω) at the amplifier output. This will attenuate the feedthrough signal. (This is not an issue for multiplexer applications where the outputs of multiple ADs are tied together as long as at least one channel is in the ON state.) The input impedance of the disable pin is about kω in parallel with a few pf. When grounded, about µa flows out

13 CLOSED-LOOP db SHIFT Degrees db BANDWIDTH MHz NORMALIZED db DIFFERENTIAL % DIFFERENTIAL Degrees AD of the disable the disable pin for ± V supplies. If driven by complementary output CMOS logic (such as the HC), the disable time (until the output goes high impedance) is about ns and the enable time (to low impedance output) is about ns on ± V supplies. The enable time can be extended to about ns by using open drain logic such as the HC. When operated on ± V supplies, the AD disable pin may be driven by open drain logic such as the C9. In this case, adding a kω pull-up resistor from the disable pin to the plus supply will decrease the enable time to about ns. If there is a nonzero voltage present on the amplifier's output at the time it is switched to the disabled state, some additional decay time will be required for the output voltage to relax to zero. The total time for the output to go to zero will generally be about ns and is somewhat dependent on the load impedance = + R F = R L = Ω f C =.MHz IRE MODULATED RAMP SUPPLY VOLTAGE ± Volts OPERATION AS A VIDEO LINE DRIVER The AD is designed to offer outstanding performance at closed-loop gains of one or greater. At a gain of, the AD makes an excellent video line driver. The low differential gain and phase errors and wide. db bandwidth are nearly independent of supply voltage and load (as seen in Figures 9 and ). Figure 9. Differential Gain and Phase vs. Supply Voltage +. R L = Ω ±V. ±. CABLE AD.µF.µF CABLE UT Figure. A Video Line Driver Operating at a Gain of + = + R L = Ω R L = k ±. ±V k M M M Figure. Fine-Scale Gain (Normalized) vs. Frequency for Various Supply Voltages, Gain = +, R F = Ω 9 G = + R L = Ω = mv p-p R F = PEAKING.dB ±.V ±.V R F = PEAKING.dB R F = k SUPPLY VOLTAGE - ±Volts Figure. Closed-Loop Gain and Phase vs. Frequency, G = +, R L =, R F = Ω Figure. db Bandwidth vs. Supply Voltage, Gain = +, R L = Ω

14 FEEDTHROUGH db CLOSED-LOOP db SHIFT Degrees AD : VIDEO MULTIPLEXER The outputs of two ADs can be wired together to form a : mux without degrading the flatness of the gain response. Figure shows a recommended configuration which results in. db bandwidth of MHz and OFF channel isolation of db at MHz on ± V supplies. The time to switch between channels is about. µs when the disable pins are driven by open drain output logic. Adding pull-up resistors to the logic outputs or using complementary output logic (such as the HC) reduces the switching time to about ns. The switching time is only slightly affected by the signal level. A +V.µF AD.µF V +V.µF CABLE UT 9 mv ns B AD.µF V V SW % HC V Figure. A Fast Switching : Video Mux Figure. Channel Switching Time for the : Mux V S =.. 9 Figure. : Mux OFF Channel Feedthrough vs. Frequency Figure. : Mux ON Channel Gain and Phase vs. Frequency

15 FEEDTHROUGH db CLOSED-LOOP db SHIFT Degrees AD N: MULTIPLEXER A multiplexer of arbitrary size can be formed by combining the desired number of ADs together with the appropriate selection logic. The schematic in Figure shows a recommendation for a : mux which may be useful for driving a high impedance such as the input to a video A/D converter (such as the AD). The output series resistors effectively compensate for the combined output capacitance of the OFF channels plus the input capacitance of the A/D while maintaining wide bandwidth. In the case illustrated, the. db bandwidth is about MHz with no peaking. Switching time and OFF channel isolation (for the : mux) are about ns and db at MHz, respectively., A kω.µf Ω AD.µF SELECT A kω.µf. 9, B AD.µF Ω SELECT B... R L = kω kω.µf R L UT C L.. C L = pf., C AD Ω.µF SELECT C Figure. : Mux ON Channel Gain and Phase vs. Frequency kω, D.µF Ω AD.µF SELECT D Figure. A : Multiplexer Driving a High Impedance Figure. : Mux OFF Channel Feedthrough vs. Frequency

16 AD OUTLINE DIMENSIONS Dimensions shown in inches and (mm). Plastic Mini-DIP (N) Package PIN. ±. (.9 ±.).9 (9.9) MAX. (.). (.). ±. (.9 ±.). (.) REF C /9. (.) MIN. ±. (. ±.). (.) BSC. (.) NOM. ±. (. ±.) SEATING PLANE. ±. (. ±.) Cerdip (Q) Package. (.) MIN. (.) MAX PIN. (.) MAX. (.). (.). (.). (.). (.9) MAX. (.) BSC. (.). (.). (.). (.9). (.). (.). (.) MIN SEATING PLANE. (.).9 (.). (.). (.) -Pin SOIC (R) Package. (.). (.). (.9) PIN. (.99). (.). (.). (.).9 (.).9 (.). (.) BSC.9 (.). (.). (.9).9 (.9).9 (.). (.9). (.) x CHAMF.9 (.). (.).9 (.9). (.). (.) All brand or product names mentioned are trademarks or registered trademarks of their respective holders. PRINTED IN U.S.A.

Improved Second Source to the EL2020 ADEL2020

Improved Second Source to the EL2020 ADEL2020 Improved Second Source to the EL ADEL FEATURES Ideal for Video Applications.% Differential Gain. Differential Phase. db Bandwidth to 5 MHz (G = +) High Speed 9 MHz Bandwidth ( db) 5 V/ s Slew Rate ns Settling

More information

Dual, Current Feedback Low Power Op Amp AD812

Dual, Current Feedback Low Power Op Amp AD812 a FEATURES Two Video Amplifiers in One -Lead SOIC Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = ): Gain Flatness. db to MHz.% Differential Gain Error. Differential

More information

Single Supply, Low Power Triple Video Amplifier AD813

Single Supply, Low Power Triple Video Amplifier AD813 a FEATURES Low Cost Three Video Amplifiers in One Package Optimized for Driving Cables in Video Systems Excellent Video Specifications (R L = 15 ) Gain Flatness.1 db to 5 MHz.3% Differential Gain Error.6

More information

Single Supply, Low Power, Triple Video Amplifier AD8013

Single Supply, Low Power, Triple Video Amplifier AD8013 a FEATURES Three Video Amplifiers in One Package Drives Large Capacitive Load Excellent Video Specifications (R L = 5 ) Gain Flatness. db to MHz.% Differential Gain Error. Differential Phase Error Low

More information

Low Cost, General Purpose High Speed JFET Amplifier AD825

Low Cost, General Purpose High Speed JFET Amplifier AD825 a FEATURES High Speed 41 MHz, 3 db Bandwidth 125 V/ s Slew Rate 8 ns Settling Time Input Bias Current of 2 pa and Noise Current of 1 fa/ Hz Input Voltage Noise of 12 nv/ Hz Fully Specified Power Supplies:

More information

200 ma Output Current High-Speed Amplifier AD8010

200 ma Output Current High-Speed Amplifier AD8010 a FEATURES 2 ma of Output Current 9 Load SFDR 54 dbc @ MHz Differential Gain Error.4%, f = 4.43 MHz Differential Phase Error.6, f = 4.43 MHz Maintains Video Specifications Driving Eight Parallel 75 Loads.2%

More information

Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820

Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820 a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from + V to + V Dual Supply Capability from. V to 8 V Excellent Load

More information

Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820

Single Supply, Rail to Rail Low Power FET-Input Op Amp AD820 a FEATURES True Single Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single Supply Capability from V to V Dual Supply Capability from. V to 8 V Excellent Load Drive

More information

250 MHz, General Purpose Voltage Feedback Op Amps AD8047/AD8048

250 MHz, General Purpose Voltage Feedback Op Amps AD8047/AD8048 5 MHz, General Purpose Voltage Feedback Op Amps AD8/AD88 FEATURES Wide Bandwidth AD8, G = + AD88, G = + Small Signal 5 MHz 6 MHz Large Signal ( V p-p) MHz 6 MHz 5.8 ma Typical Supply Current Low Distortion,

More information

High Speed, Low Power Dual Op Amp AD827

High Speed, Low Power Dual Op Amp AD827 a FEATURES HIGH SPEED 50 MHz Unity Gain Stable Operation 300 V/ s Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads EXCELLENT VIDEO PERFORMANCE 0.04% Differential Gain @ 4.4 MHz 0.19 Differential

More information

High-Speed, Low-Power Dual Operational Amplifier AD826

High-Speed, Low-Power Dual Operational Amplifier AD826 a FEATURES High Speed: MHz Unity Gain Bandwidth 3 V/ s Slew Rate 7 ns Settling Time to.% Low Power: 7. ma Max Power Supply Current Per Amp Easy to Use: Drives Unlimited Capacitive Loads ma Min Output Current

More information

Dual Picoampere Input Current Bipolar Op Amp AD706

Dual Picoampere Input Current Bipolar Op Amp AD706 a FEATURE HIGH DC PRECISION V max Offset Voltage.6 V/ C max Offset Drift pa max Input Bias Current LOW NOISE. V p-p Voltage Noise,. Hz to Hz LOW POWER A Supply Current Available in -Lead Plastic Mini-DlP,

More information

High Common-Mode Voltage Difference Amplifier AD629

High Common-Mode Voltage Difference Amplifier AD629 a FEATURES Improved Replacement for: INAP and INAKU V Common-Mode Voltage Range Input Protection to: V Common Mode V Differential Wide Power Supply Range (. V to V) V Output Swing on V Supply ma Max Power

More information

Dual, Low Power Video Op Amp AD828

Dual, Low Power Video Op Amp AD828 a FEATURES Excellent Video Performance Differential Gain and Phase Error of.% and. High Speed MHz db Bandwidth (G = +) V/ s Slew Rate ns Settling Time to.% Low Power ma Max Power Supply Current High Output

More information

Wideband, High Output Current, Fast Settling Op Amp AD842

Wideband, High Output Current, Fast Settling Op Amp AD842 a FEATURES AC PERFORMAE Gain Bandwidth Product: 8 MHz (Gain = 2) Fast Settling: ns to.1% for a V Step Slew Rate: 375 V/ s Stable at Gains of 2 or Greater Full Power Bandwidth: 6. MHz for V p-p DC PERFORMAE

More information

High Output Current Differential Driver AD815

High Output Current Differential Driver AD815 a FEATURES Flexible Configuration Differential Input and Output Driver or Two Single-Ended Drivers Industrial Temperature Range High Output Power Thermally Enhanced SOIC 4 ma Minimum Output Drive/Amp,

More information

Dual Picoampere Input Current Bipolar Op Amp AD706

Dual Picoampere Input Current Bipolar Op Amp AD706 Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available

More information

OBSOLETE. Parameter AD9621 AD9622 AD9623 AD9624 Units

OBSOLETE. Parameter AD9621 AD9622 AD9623 AD9624 Units a FEATURES MHz Small Signal Bandwidth MHz Large Signal BW ( V p-p) High Slew Rate: V/ s Low Distortion: db @ MHz Fast Settling: ns to.%. nv/ Hz Spectral Noise Density V Supply Operation Wideband Voltage

More information

High Speed, Low Power Dual Op Amp AD827

High Speed, Low Power Dual Op Amp AD827 a FEATURES High Speed 50 MHz Unity Gain Stable Operation 300 V/ms Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads Excellent Video Performance 0.04% Differential Gain @ 4.4 MHz 0.198 Differential

More information

Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820

Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5

More information

Quad Picoampere Input Current Bipolar Op Amp AD704

Quad Picoampere Input Current Bipolar Op Amp AD704 a FEATURES High DC Precision 75 V Max Offset Voltage V/ C Max Offset Voltage Drift 5 pa Max Input Bias Current.2 pa/ C Typical I B Drift Low Noise.5 V p-p Typical Noise,. Hz to Hz Low Power 6 A Max Supply

More information

Dual Picoampere Input Current Bipolar Op Amp AD706

Dual Picoampere Input Current Bipolar Op Amp AD706 Dual Picoampere Input Current Bipolar Op Amp FEATURES High DC Precision V Max Offset Voltage.5 V/ C Max Offset Drift 2 pa Max Input Bias Current.5 V p-p Voltage Noise,. Hz to Hz 75 A Supply Current Available

More information

High Accuracy 8-Pin Instrumentation Amplifier AMP02

High Accuracy 8-Pin Instrumentation Amplifier AMP02 a FEATURES Low Offset Voltage: 100 V max Low Drift: 2 V/ C max Wide Gain Range 1 to 10,000 High Common-Mode Rejection: 115 db min High Bandwidth (G = 1000): 200 khz typ Gain Equation Accuracy: 0.5% max

More information

Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps AD9631/AD9632

Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps AD9631/AD9632 a Ultralow Distortion, Wide Bandwidth Voltage Feedback Op Amps / FEATURES Wide Bandwidth, G = +, G = +2 Small Signal 32 MHz 25 MHz Large Signal (4 V p-p) 75 MHz 8 MHz Ultralow Distortion (SFDR), Low Noise

More information

High Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection

High Common-Mode Rejection. Differential Line Receiver SSM2141 REV. B FUNCTIONAL BLOCK DIAGRAM FEATURES. High Common-Mode Rejection a FEATURES High Common-Mode Rejection DC: 100 db typ 60 Hz: 100 db typ 20 khz: 70 db typ 40 khz: 62 db typ Low Distortion: 0.001% typ Fast Slew Rate: 9.5 V/ s typ Wide Bandwidth: 3 MHz typ Low Cost Complements

More information

Quad Picoampere Input Current Bipolar Op Amp AD704

Quad Picoampere Input Current Bipolar Op Amp AD704 a FEATURES High DC Precision 75 V max Offset Voltage V/ C max Offset Voltage Drift 5 pa max Input Bias Current.2 pa/ C typical I B Drift Low Noise.5 V p-p typical Noise,. Hz to Hz Low Power 6 A max Supply

More information

Quad 150 MHz Rail-to-Rail Amplifier AD8044

Quad 150 MHz Rail-to-Rail Amplifier AD8044 a FEATURES Single AD84 and Dual AD842 Also Available Fully Specified at + V, +5 V, and 5 V Supplies Output Swings to Within 25 mv of Either Rail Input Voltage Range Extends 2 mv Below Ground No Phase Reversal

More information

Precision, 16 MHz CBFET Op Amp AD845

Precision, 16 MHz CBFET Op Amp AD845 a FEATURES Replaces Hybrid Amplifiers in Many Applications AC PERFORMANCE: Settles to 0.01% in 350 ns 100 V/ s Slew Rate 12.8 MHz Min Unity Gain Bandwidth 1.75 MHz Full Power Bandwidth at 20 V p-p DC PERFORMANCE:

More information

Dual 260 MHz Gain = +2.0 & +2.2 Buffer AD8079

Dual 260 MHz Gain = +2.0 & +2.2 Buffer AD8079 a FEATURES Factory Set Gain AD879A: Gain = +2. (Also +. &.) AD879B: Gain = +2.2 (Also + &.2) Gain of 2.2 Compensates for System Gain Loss Minimizes External Components Tight Control of Gain and Gain Matching

More information

High Speed, G = +2, Low Cost, Triple Op Amp ADA4862-3

High Speed, G = +2, Low Cost, Triple Op Amp ADA4862-3 High Speed,, Low Cost, Triple Op Amp ADA4862-3 FEATURES Ideal for RGB/HD/SD video Supports 8i/72p resolution High speed 3 db bandwidth: 3 MHz Slew rate: 75 V/μs Settling time: 9 ns (.5%). db flatness:

More information

Dual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature

Dual Picoampere Input Current Bipolar Op Amp AD706. Data Sheet. Figure 1. Input Bias Current vs. Temperature Data Sheet Dual Picoampere Input Current Bipolar Op Amp Rev. F Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by

More information

Very Low Distortion, Precision Difference Amplifier AD8274

Very Low Distortion, Precision Difference Amplifier AD8274 Very Low Distortion, Precision Difference Amplifier AD8274 FEATURES Very low distortion.2% THD + N (2 khz).% THD + N ( khz) Drives Ω loads Excellent gain accuracy.3% maximum gain error 2 ppm/ C maximum

More information

Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822

Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp FEATURES True Single-Supply Operation Output Swings Rail-to-Rail Input Voltage Range Extends Below Ground Single-Supply Capability from 3 V to 36

More information

High Speed, Low Power Monolithic Op Amp AD847

High Speed, Low Power Monolithic Op Amp AD847 a FEATURES Superior Performance High Unity Gain BW: MHz Low Supply Current:.3 ma High Slew Rate: 3 V/ s Excellent Video Specifications.% Differential Gain (NTSC and PAL).19 Differential Phase (NTSC and

More information

AD9300 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 12 V 5%; C L = 10 pf; R L = 2 k, unless otherwise noted) COMMERCIAL 0 C to +70 C Test AD9300K

AD9300 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 12 V 5%; C L = 10 pf; R L = 2 k, unless otherwise noted) COMMERCIAL 0 C to +70 C Test AD9300K a FEATURES 34 MHz Full Power Bandwidth 0.1 db Gain Flatness to 8 MHz 72 db Crosstalk Rejection @ 10 MHz 0.03 /0.01% Differential Phase/Gain Cascadable for Switch Matrices MIL-STD-883 Compliant Versions

More information

High Speed BUFFER AMPLIFIER

High Speed BUFFER AMPLIFIER High Speed BUFFER AMPLIFIER FEATURES WIDE BANDWIDTH: MHz HIGH SLEW RATE: V/µs HIGH OUTPUT CURRENT: 1mA LOW OFFSET VOLTAGE: 1.mV REPLACES HA-33 IMPROVED PERFORMANCE/PRICE: LH33, LTC11, HS APPLICATIONS OP

More information

270 MHz, 400 μa Current Feedback Amplifier AD8005

270 MHz, 400 μa Current Feedback Amplifier AD8005 Data Sheet 27 MHz, μa Current Feedback Amplifier AD85 FEATURES Ultralow power μa power supply current ( mw on ±5 VS) Specified for single supply operation High speed 27 MHz, 3 db bandwidth (G = +) 7 MHz,

More information

Dual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP

Dual Precision, Low Cost, High Speed BiFET Op Amp AD712-EP Dual Precision, Low Cost, High Speed BiFET Op Amp FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +125 C) Controlled manufacturing baseline One

More information

High-Speed, Low-Power Dual Operational Amplifier AD826

High-Speed, Low-Power Dual Operational Amplifier AD826 a FEATURES High Speed: MHz Unity Gain Bandwidth 3 V/ s Slew Rate 7 ns Settling Time to.% Low Power: 7. ma Max Power Supply Current Per Amp Easy to Use: Drives Unlimited Capacitive Loads ma Min Output Current

More information

LM6172 Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers

LM6172 Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers LM6172 Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers General Description The LM6172 is a dual high speed voltage feedback amplifier. It is unity-gain stable and provides excellent

More information

ADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe

ADA485-/ADA485- TABLE OF CONTENTS Features... Applications... Pin Configurations... General Description... Revision History... Specifications... 3 Spe NC NC NC NC 5 6 7 8 6 NC 4 PD 3 PD FEATURES Ultralow power-down current: 5 na/amplifier maximum Low quiescent current:.4 ma/amplifier High speed 75 MHz, 3 db bandwidth V/μs slew rate 85 ns settling time

More information

High Voltage, Low Noise, Low Distortion, Unity-Gain Stable, High Speed Op Amp ADA4898-1/ADA4898-2

High Voltage, Low Noise, Low Distortion, Unity-Gain Stable, High Speed Op Amp ADA4898-1/ADA4898-2 FEATURES Ultralow noise.9 nv/ Hz.4 pa/ Hz. nv/ Hz at Hz Ultralow distortion: 93 dbc at 5 khz Wide supply voltage range: ±5 V to ±6 V High speed 3 db bandwidth: 65 MHz (G = +) Slew rate: 55 V/µs Unity gain

More information

Quad Picoampere Input Current Bipolar Op Amp AD704

Quad Picoampere Input Current Bipolar Op Amp AD704 a FEATURES High DC Precision 75 V Max Offset Voltage V/ C Max Offset Voltage Drift 5 pa Max Input Bias Current.2 pa/ C Typical I B Drift Low Noise.5 V p-p Typical Noise,. Hz to Hz Low Power 6 A Max Supply

More information

AD836/AD837 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 5 V; R LOAD = 1 ; A V = +1 (AD836); A V = +2 (AD837),, open, unless otherwise noted) AD8

AD836/AD837 SPECIFICATIONS ELECTRICAL CHARACTERISTICS ( V S = 5 V; R LOAD = 1 ; A V = +1 (AD836); A V = +2 (AD837),, open, unless otherwise noted) AD8 a FEATURES Superb Clamping Characteristics 3 mv Clamp Error 1.5 ns Overdrive Recovery Minimized Nonlinear Clamping Region 24 MHz Clamp Input Bandwidth 3.9 V Clamp Input Range Wide Bandwidth AD836 AD837

More information

380 MHz, 25 ma, Triple 2:1 Multiplexers AD8183/AD8185

380 MHz, 25 ma, Triple 2:1 Multiplexers AD8183/AD8185 a FEATURES Fully Buffered Inputs and Outputs Fast Channel-to-Channel Switching: 5 ns High Speed 38 MHz Bandwidth ( 3 db) 2 mv p-p 3 MHz Bandwidth ( 3 db) 2 V p-p V/ s Slew Rate G = +, 2 V Step 5 V/ s Slew

More information

KM4110/KM mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers

KM4110/KM mA, Low Cost, +2.7V & +5V, 75MHz Rail-to-Rail Amplifiers + + www.fairchildsemi.com KM411/KM41.5mA, Low Cost, +.7V & +5V, 75MHz Rail-to-Rail Amplifiers Features 55µA supply current 75MHz bandwidth Power down to I s = 33µA (KM41) Fully specified at +.7V and +5V

More information

Low Cost 270 MHz Differential Receiver Amplifiers AD8129/AD8130

Low Cost 270 MHz Differential Receiver Amplifiers AD8129/AD8130 a FEATURES High Speed AD8: 7 MHz, 9 V/ s @ G = AD89: MHz, 6 V/ s @ G = High CMRR 94 db Min, DC to khz 8 db Min @ MHz 7 db @ MHz High Input Impedance: M Differential Input Common-Mode Range.5 V Low Noise

More information

OBSOLETE. Low Cost Quad Voltage Controlled Amplifier SSM2164 REV. 0

OBSOLETE. Low Cost Quad Voltage Controlled Amplifier SSM2164 REV. 0 a FEATURES Four High Performance VCAs in a Single Package.2% THD No External Trimming 12 db Gain Range.7 db Gain Matching (Unity Gain) Class A or AB Operation APPLICATIONS Remote, Automatic, or Computer

More information

Dual FET-Input, Low Distortion OPERATIONAL AMPLIFIER

Dual FET-Input, Low Distortion OPERATIONAL AMPLIFIER www.burr-brown.com/databook/.html Dual FET-Input, Low Distortion OPERATIONAL AMPLIFIER FEATURES LOW DISTORTION:.3% at khz LOW NOISE: nv/ Hz HIGH SLEW RATE: 25V/µs WIDE GAIN-BANDWIDTH: MHz UNITY-GAIN STABLE

More information

HA-2520, HA-2522, HA-2525

HA-2520, HA-2522, HA-2525 HA-, HA-, HA- Data Sheet September 99 File Number 9. MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-// comprise a series of operational amplifiers delivering an unsurpassed

More information

High Output Current Differential Driver AD815

High Output Current Differential Driver AD815 a FEATURES Flexible Configuration Differential Input & Output Driver or Two Single-Ended Drivers High Output Power Power Package dbm Differential Line Drive for ADSL Application V p-p Differential Output

More information

Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD820

Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD820 Single-Supply, Rail-to-Rail, Low Power FET-Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V

More information

AD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES

AD MHz, 20 V/μs, G = 1, 10, 100, 1000 i CMOS Programmable Gain Instrumentation Amplifier. Preliminary Technical Data FEATURES Preliminary Technical Data 0 MHz, 20 V/μs, G =, 0, 00, 000 i CMOS Programmable Gain Instrumentation Amplifier FEATURES Small package: 0-lead MSOP Programmable gains:, 0, 00, 000 Digital or pin-programmable

More information

Quad Audio Switch REV. B BLOCK DIAGRAM OF ONE SWITCH CHANNEL

Quad Audio Switch REV. B BLOCK DIAGRAM OF ONE SWITCH CHANNEL a FEATURES CIickless Bilateral Audio Switching Four SPST Switches in a -Pin Package Ultralow THD+N:.8% @ khz ( V rms, R L = k ) Low Charge Injection: 3 pc typ High OFF Isolation: db typ (R L = k @ khz)

More information

Rail-to-Rail, High Output Current Amplifier AD8397

Rail-to-Rail, High Output Current Amplifier AD8397 Rail-to-Rail, High Output Current Amplifier FEATURES Dual operational amplifier Voltage feedback Wide supply range from 3 V to 24 V Rail-to-rail output Output swing to within.5 V of supply rails High linear

More information

Four-Channel Sample-and-Hold Amplifier AD684

Four-Channel Sample-and-Hold Amplifier AD684 a FEATURES Four Matched Sample-and-Hold Amplifiers Independent Inputs, Outputs and Control Pins 500 ns Hold Mode Settling 1 s Maximum Acquisition Time to 0.01% Low Droop Rate: 0.01 V/ s Internal Hold Capacitors

More information

Octal Sample-and-Hold with Multiplexed Input SMP18

Octal Sample-and-Hold with Multiplexed Input SMP18 a FEATURES High Speed Version of SMP Internal Hold Capacitors Low Droop Rate TTL/CMOS Compatible Logic Inputs Single or Dual Supply Operation Break-Before-Make Channel Addressing Compatible With CD Pinout

More information

Low Cost, Low Power Video Op Amp AD818

Low Cost, Low Power Video Op Amp AD818 Low Cost, Low Power Video Op Amp FEATURES Low Cost Excellent Video Performance 55 MHz. db Bandwidth (Gain = +2).% and.5 Differential Gain and Phase Errors High Speed 3 MHz Bandwidth (3 db, G = +2) MHz

More information

1.5 GHz Ultrahigh Speed Op Amp AD8000

1.5 GHz Ultrahigh Speed Op Amp AD8000 .5 GHz Ultrahigh Speed Op Amp AD8 FEATURES High speed.5 GHz, db bandwidth (G = +) 65 MHz, full power bandwidth (, VO = 2 V p-p) Slew rate: 4 V/µs.% settling time: 2 ns Excellent video specifications. db

More information

800 MHz, 50 mw Current Feedback Amplifier AD8001

800 MHz, 50 mw Current Feedback Amplifier AD8001 a FEATURES Excellent Video Specifications (R L = 5, ) Gain Flatness. db to MHz.% Differential Gain Error.25 Differential Phase Error Low Power 5.5 ma Max Power Supply Current (55 mw) High Speed and Fast

More information

Single-Supply, High Speed, Triple Op Amp with Charge Pump ADA4858-3

Single-Supply, High Speed, Triple Op Amp with Charge Pump ADA4858-3 Single-Supply, High Speed, Triple Op Amp with Charge Pump FEATURES Integrated charge pump Supply range: 3 V to 5.5 V Output range: 3.3 V to.8 V 5 ma maximum output current for external use at 3 V High

More information

REV. D Ultralow Distortion High Speed Amplifiers AD8007/AD8008 FEATURES CONNECTION DIAGRAMS Extremely Low Distortion Second Harmonic 88 5 MHz SO

REV. D Ultralow Distortion High Speed Amplifiers AD8007/AD8008 FEATURES CONNECTION DIAGRAMS Extremely Low Distortion Second Harmonic 88 5 MHz SO Ultralow Distortion High Speed Amplifiers FEATURES CONNECTION DIAGRAMS Extremely Low Distortion Second Harmonic 88 dbc @ 5 MHz SOIC (R) SC7 (KS-5) 8 dbc @ MHz (AD87) AD87 AD87 NC V (Top View) 8 NC OUT

More information

800 MHz, 4:1 Analog Multiplexer ADV3221/ADV3222

800 MHz, 4:1 Analog Multiplexer ADV3221/ADV3222 8 MHz, : Analog Multiplexer ADV/ADV FEATURES Excellent ac performance db bandwidth 8 MHz ( mv p-p) 7 MHz ( V p-p) Slew rate: V/μs Low power: 7 mw, VS = ± V Excellent video performance MHz,. db gain flatness.%

More information

High Speed, Low Power Dual Op Amp AD827

High Speed, Low Power Dual Op Amp AD827 a FEATURES High Speed 50 MHz Unity Gain Stable Operation 300 V/ms Slew Rate 120 ns Settling Time Drives Unlimited Capacitive Loads Excellent Video Performance 0.04% Differential Gain @ 4.4 MHz 0.198 Differential

More information

AD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo

AD864/AD8642/AD8643 TABLE OF CONTENTS Specifications... 3 Electrical Characteristics... 3 Absolute Maximum Ratings... 5 ESD Caution... 5 Typical Perfo FEATURES Low supply current: 25 µa max Very low input bias current: pa max Low offset voltage: 75 µv max Single-supply operation: 5 V to 26 V Dual-supply operation: ±2.5 V to ±3 V Rail-to-rail output Unity-gain

More information

PART MAX4144ESD MAX4146ESD. Typical Application Circuit. R t IN- IN+ TWISTED-PAIR-TO-COAX CABLE CONVERTER

PART MAX4144ESD MAX4146ESD. Typical Application Circuit. R t IN- IN+ TWISTED-PAIR-TO-COAX CABLE CONVERTER 9-47; Rev ; 9/9 EVALUATION KIT AVAILABLE General Description The / differential line receivers offer unparalleled high-speed performance. Utilizing a threeop-amp instrumentation amplifier architecture,

More information

700 MHz, 5 ma 4-to-1 Video Multiplexer AD8184

700 MHz, 5 ma 4-to-1 Video Multiplexer AD8184 a FEATURES Single and Dual -to- Also Available (AD88 and AD88) Fully Buffered Inputs and Outputs Fast Channel Switching: ns High Speed > 7 MHz Bandwidth ( db) > 7 V/ s Slew Rate Fast Settling Time of ns

More information

HA4600. Features. 480MHz, SOT-23, Video Buffer with Output Disable. Applications. Pinouts. Ordering Information. Truth Table

HA4600. Features. 480MHz, SOT-23, Video Buffer with Output Disable. Applications. Pinouts. Ordering Information. Truth Table TM Data Sheet June 2000 File Number 3990.6 480MHz, SOT-23, Video Buffer with Output Disable The is a very wide bandwidth, unity gain buffer ideal for professional video switching, HDTV, computer monitor

More information

Ultrafast Comparators AD96685/AD96687

Ultrafast Comparators AD96685/AD96687 a FEATURES Fast: 2.5 ns Propagation Delay Low Power: 118 mw per Comparator Packages: DIP, SOIC, PLCC Power Supplies: +5 V, 5.2 V Logic Compatibility: ECL 50 ps Delay Dispersion APPLICATIONS High Speed

More information

Low Cost Instrumentation Amplifier AD622

Low Cost Instrumentation Amplifier AD622 a FEATURES Easy to Use Low Cost Solution Higher Performance than Two or Three Op Amp Design Unity Gain with No External Resistor Optional Gains with One External Resistor (Gain Range 2 to ) Wide Power

More information

Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820

Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD820 Single-Supply, Rail-to-Rail, Low Power, FET Input Op Amp AD82 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 5 V

More information

Matched Monolithic Quad Transistor MAT04

Matched Monolithic Quad Transistor MAT04 a FEATURES Low Offset Voltage: 200 V max High Current Gain: 400 min Excellent Current Gain Match: 2% max Low Noise Voltage at 100 Hz, 1 ma: 2.5 nv/ Hz max Excellent Log Conformance: rbe = 0.6 max Matching

More information

OBSOLETE. Self-Contained Audio Preamplifier SSM2017 REV. B

OBSOLETE. Self-Contained Audio Preamplifier SSM2017 REV. B a FEATURES Excellent Noise Performance: 950 pv/ Hz or 1.5 db Noise Figure Ultralow THD: < 0.01% @ G = 100 Over the Full Audio Band Wide Bandwidth: 1 MHz @ G = 100 High Slew Rate: 17 V/ s typ Unity Gain

More information

6 db Differential Line Receiver

6 db Differential Line Receiver a FEATURES High Common-Mode Rejection DC: 9 db typ Hz: 9 db typ khz: 8 db typ Ultralow THD:.% typ @ khz Fast Slew Rate: V/ s typ Wide Bandwidth: 7 MHz typ (G = /) Two Gain Levels Available: G = / or Low

More information

1.5 GHz Ultrahigh Speed Op Amp AD8000

1.5 GHz Ultrahigh Speed Op Amp AD8000 .5 GHz Ultrahigh Speed Op Amp AD8 FEATURES High speed.5 GHz, db bandwidth (G = +) 65 MHz, full power bandwidth (, VO = 2 V p-p) Slew rate: 4 V/µs.% settling time: 2 ns Excellent video specifications. db

More information

HA MHz, High Slew Rate, High Output Current Buffer. Description. Features. Applications. Ordering Information. Pinouts.

HA MHz, High Slew Rate, High Output Current Buffer. Description. Features. Applications. Ordering Information. Pinouts. SEMICONDUCTOR HA-2 November 99 Features Voltage Gain...............................99 High Input Impedance.................... kω Low Output Impedance....................... Ω Very High Slew Rate....................

More information

OP SPECIFICATIONS ELECTRICAL CHARACTERISTICS (V S = ± V, T A = C, unless otherwise noted.) OPA/E OPF OPG Parameter Symbol Conditions Min Typ Max Min T

OP SPECIFICATIONS ELECTRICAL CHARACTERISTICS (V S = ± V, T A = C, unless otherwise noted.) OPA/E OPF OPG Parameter Symbol Conditions Min Typ Max Min T a FEATURES Excellent Speed:. V/ms Typ Fast Settling (.%): ms Typ Unity-Gain Stable High-Gain Bandwidth: MHz Typ Low Input Offset Voltage: mv Max Low Offset Voltage Drift: mv/ C Max High Gain: V/mV Min

More information

OBSOLETE. High-Speed, Dual Operational Amplifier OP271 REV. A. Figure 1. Simplified Schematic (One of the two amplifiers is shown.

OBSOLETE. High-Speed, Dual Operational Amplifier OP271 REV. A. Figure 1. Simplified Schematic (One of the two amplifiers is shown. a FEATURES Excellent Speed:. V/ms Typ Fast Settling (.%): ms Typ Unity-Gain Stable High-Gain Bandwidth: MHz Typ Low Input Offset Voltage: mv Max Low Offset Voltage Drift: mv/ C Max High Gain: V/mV Min

More information

LM6118/LM6218 Fast Settling Dual Operational Amplifiers

LM6118/LM6218 Fast Settling Dual Operational Amplifiers Fast Settling Dual Operational Amplifiers General Description The LM6118/LM6218 are monolithic fast-settling unity-gain-compensated dual operational amplifiers with ±20 ma output drive capability. The

More information

Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION

Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8274 FUNCTIONAL BLOCK DIAGRAM +V S FEATURES APPLICATIONS GENERAL DESCRIPTION Very Low Distortion, Dual-Channel, High Precision Difference Amplifier AD8273 FEATURES ±4 V HBM ESD Very low distortion.25% THD + N (2 khz).15% THD + N (1 khz) Drives 6 Ω loads Two gain settings Gain of

More information

HA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information

HA-2600, HA Features. 12MHz, High Input Impedance Operational Amplifiers. Applications. Pinouts. Ordering Information HA26, HA26 September 998 File Number 292.3 2MHz, High Input Impedance Operational Amplifiers HA26/26 are internally compensated bipolar operational amplifiers that feature very high input impedance (MΩ,

More information

Precision Micropower Single Supply Operational Amplifier OP777

Precision Micropower Single Supply Operational Amplifier OP777 a FEATURES Low Offset Voltage: 1 V Max Low Input Bias Current: 1 na Max Single-Supply Operation: 2.7 V to 3 V Dual-Supply Operation: 1.35 V to 15 V Low Supply Current: 27 A/Amp Unity Gain Stable No Phase

More information

Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276

Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD8276 Low Power, Wide Supply Range, Low Cost Unity-Gain Difference Amplifier AD87 FEATURES Wide input range Rugged input overvoltage protection Low supply current: μa maximum Low power dissipation:. mw at VS

More information

4 AD548. Precision, Low Power BiFET Op Amp

4 AD548. Precision, Low Power BiFET Op Amp a FEATURES Enhanced Replacement for LF1 and TL1 DC Performance: A max Quiescent Current 1 pa max Bias Current, Warmed Up (AD8C) V max Offset Voltage (AD8C) V/ C max Drift (AD8C) V p-p Noise,.1 Hz to 1

More information

Low Power, 350 MHz Voltage Feedback Amplifiers AD8038/AD8039

Low Power, 350 MHz Voltage Feedback Amplifiers AD8038/AD8039 Low Power, MHz Voltage Feedback Amplifiers AD88/AD89 FEATURES Low power: ma supply current/amp High speed MHz, db bandwidth (G = +) V/μs slew rate Low cost Low noise 8 nv/ Hz @ khz fa/ Hz @ khz Low input

More information

Dual 350 MHz Low Power Amplifier AD8012 *

Dual 350 MHz Low Power Amplifier AD8012 * Dual 5 MHz Low Power Amplifier AD82 * FEATURES Low Power.7 ma/amplifier Supply Current Fully Specified for 5 V and 5 V Supplies High Output Current, 25 ma High Speed 5 MHz, db Bandwidth (G = ) 5 MHz, db

More information

6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable

6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable 99 Rev ; /99 EVALUATION KIT AVAILABLE 65V/µs, Wideband, High-Output-Current, Single- General Description The // single-ended-todifferential line drivers are designed for high-speed communications. Using

More information

HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8

HA MHz Video Buffer. Features. Applications. Ordering Information. Pinouts. Data Sheet February 6, 2006 FN2924.8 HA-533 Data Sheet February 6, 26 FN2924.8 25MHz Video Buffer The HA-533 is a unity gain monolithic IC designed for any application requiring a fast, wideband buffer. Featuring a bandwidth of 25MHz and

More information

15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP

15 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP 5 MHz, Rail-to-Rail, Dual Operational Amplifier OP262-EP FEATURES Supports defense and aerospace applications (AQEC standard) Military temperature range ( 55 C to +25 C) Controlled manufacturing baseline

More information

Low Cost Low Power Instrumentation Amplifier AD620

Low Cost Low Power Instrumentation Amplifier AD620 Low Cost Low Power Instrumentation Amplifier AD60 FEATURES Easy to use Gain set with one external resistor (Gain range to 0,000) Wide power supply range (±.3 V to ±8 V) Higher performance than 3 op amp

More information

Low Distortion, Precision, Wide Bandwidth Op Amp AD9617

Low Distortion, Precision, Wide Bandwidth Op Amp AD9617 a FEATURES Usable Closed-Loop Gain Range: to 4 Low Distortion: 67 dbc (2nd) at 2 MHz Small Signal Bandwidth: 9 MHz (A V = +3) Large Signal Bandwidth: 5 MHz at 4 V p-p Settling Time: ns to.%; 4 ns to.2%

More information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information

HA-2520, HA MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers. Features. Applications. Ordering Information HA-22, HA-22 Data Sheet August, 2 FN2894. 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-22/22 comprise a series of operational amplifiers delivering an unsurpassed

More information

High Speed, Low Noise Video Op Amp AD829

High Speed, Low Noise Video Op Amp AD829 High Speed, Low Noise Video Op Amp AD89 FEATURES High speed MHz bandwidth, gain = V/μs slew rate 9 ns settling time to.% Ideal for video applications.% differential gain. differential phase Low noise.7

More information

CONNECTION DIAGRAMS TO-99 (H) Package. 8-Lead Plastic Mini-DIP (N) 8-Lead SOIC (R) Package and 8-Lead Cerdip (Q) Packages

CONNECTION DIAGRAMS TO-99 (H) Package. 8-Lead Plastic Mini-DIP (N) 8-Lead SOIC (R) Package and 8-Lead Cerdip (Q) Packages FEATURES AC PERFORMANCE 500 ns Settling to 0.01% for 10 V Step 1.5 s Settling to 0.0025% for 10 V Step 75 V/ s Slew Rate 0.0003% Total Harmonic Distortion (THD) 13 MHz Gain Bandwidth Internal Compensation

More information

4 AD548. Precision, Low Power BiFET Op Amp REV. D. CONNECTION DIAGRAMS Plastic Mini-DIP (N) Package and SOIC (R)Package

4 AD548. Precision, Low Power BiFET Op Amp REV. D. CONNECTION DIAGRAMS Plastic Mini-DIP (N) Package and SOIC (R)Package a FEATURES Enhanced Replacement for LF441 and TL61 DC Performance: 2 A max Quiescent Current 1 pa max Bias Current, Warmed Up (AD48C) 2 V max Offset Voltage (AD48C) 2 V/ C max Drift (AD48C) 2 V p-p Noise,.1

More information

High Speed FET-INPUT OPERATIONAL AMPLIFIERS

High Speed FET-INPUT OPERATIONAL AMPLIFIERS OPA OPA OPA OPA OPA OPA OPA OPA OPA High Speed FET-INPUT OPERATIONAL AMPLIFIERS FEATURES FET INPUT: I B = 5pA max WIDE BANDWIDTH: MHz HIGH SLEW RATE: V/µs LOW NOISE: nv/ Hz (khz) LOW DISTORTION:.% HIGH

More information

150 μv Maximum Offset Voltage Op Amp OP07D

150 μv Maximum Offset Voltage Op Amp OP07D 5 μv Maximum Offset Voltage Op Amp OP7D FEATURES Low offset voltage: 5 µv max Input offset drift:.5 µv/ C max Low noise:.25 μv p-p High gain CMRR and PSRR: 5 db min Low supply current:. ma Wide supply

More information

Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822

Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 Single-Supply, Rail-to-Rail Low Power FET-Input Op Amp AD822 FEATURES True single-supply operation Output swings rail-to-rail Input voltage range extends below ground Single-supply capability from 3 V

More information

MIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp

MIC915. Features. General Description. Applications. Ordering Information. Pin Configuration. Pin Description. Dual 135MHz Low-Power Op Amp MIC915 Dual 135MHz Low-Power Op Amp General Description The MIC915 is a high-speed, unity-gain stable operational amplifier. It provides a gain-bandwidth product of 135MHz with a very low, 2.4mA supply

More information

High Speed FET-Input INSTRUMENTATION AMPLIFIER

High Speed FET-Input INSTRUMENTATION AMPLIFIER High Speed FET-Input INSTRUMENTATION AMPLIFIER FEATURES FET INPUT: I B = 2pA max HIGH SPEED: T S = 4µs (G =,.%) LOW OFFSET VOLTAGE: µv max LOW OFFSET VOLTAGE DRIFT: µv/ C max HIGH COMMON-MODE REJECTION:

More information