Workholding Specialists

Transcription

1 Workholding Specialists Manual ctuators NW! Lean MM Workholding System NW! ILS vailable Online: MITIT.OM 2

2 Mission Statement Our goal is to serve our customers by providing a complete range of the best low profile clamps, of the highest quality at competitive prices and delivered on time. This promise is backed and supported by our knowledgeable technical and sales staff who are available to assist our distributors and customers. ompany Profile Mitee-ite Products LL was founded in 1986 and is located in a rural setting in the lakes and mountain region of New Hampshire. We are the innovator of compact, low-profile edge clamps, which improve production in N machining centers. Our original cam action clamp was designed to improve the production process in a contract machine shop. Since that time many types of clamps have been added and are included in this catalog. These products are readily accepted because of the benefits they offer. We are known worldwide for the quality of our products and for the service we provide our customers. Our products are available through many qualified distributors around the world. or information on how to reach them or for more information about our products, visit our website: Miteeite.com or call us at and Our ad iles can now be downloaded in all formats from our website: Miteeite.com

3 Table of ontents escription lamp Type ategory Page ixture lamps am ction ixtures... 4 Knife dge lamps am ction... ixtures... 4 Series-9 lamps... am ction ixtures... 5 Machinable ixture lamps am ction ixtures... 5 Uniforce lamps Wedge... ixtures... 6 Long Length Uniforce hannel and Steel Wedge... ixtures... 6 Machinable Uniforce lamps Wedge... ixtures... 7 Machinable Long Length Uniforce lamps Wedge... ixtures... 7 OK-Vise lamps Wedge... ixtures Pitbull lamps Rocking Lever ixtures Machinable Pitbull lamps.... Rocking Lever ixtures Modular Pitbull lamps Rocking Lever Modular Multi-ixture lamps and Stops am ction Modular I Xpansion lamps Internal.... ixtures Side-Loc Xpansion lamps Internal.... ixtures Manual ctuators for Mills and Lathes... Internal... ixtures yna-orce lamps.... Ramp ixtures Vacmagic VM Vacuum Pallet hanger Vacuum System Vacmagic VM Vacuum Pallet hanger Vacuum System TalonGrip Vise Jaws Low Profile Grippers Vise VersaGrip Vise Jaws Low Profile Grippers Vise Lean MM Workholding System... Quality ontrol...inspection ompact Toe lamps am ction ixtures T-Slot Toe lamps... am ction T-Slots T-Slot Kits.... am ction T-Slots T-Slot lamps... am ction T-Slots dvant-dge lamps... am ction T-Slots Vise Pallets Pallet hanger Vise Locating Rails.... Stops ixtures luminum Sub Plates ixturing Mounting lamps Pivot ixturing Low Profile Gripping Rails Rocking Lever ccessories hip Hook Safety Kopal Mini lamps Low Profile ixtures Kopal Mono-loc lamps Worm-and-Gear T-Slots & Tapped Hole Kopal Mono-loc hain lamps... Worm-and-Gear T-Slots & Tapped Hole Strap lamps T-Slots & Tapped Hole ollet Wrenches Lathe ccessories ollet Stop Lathe ccessories Mitee-Grip Heat ctivated ixturing Replacement s ccessories ustomer pplication Photos

4 Original ixture lamps The cam action MIT-IT ixture lamp is made up of two simple components: a hardened steel socket cap screw with an offset head and a brass hexagonal washer. Low-profile makes computer programming easier am action provides fast, strong clamping Small size allows more parts per load Simple design keeps cost low NOT: lockwise rotation is recommended. Locating pin should be on the right of workpiece. G* - Location to drill and tap from edge of workpiece. Max. No. of Torque Holding lamps Number G* (t/lbs) orce Per Pack INH / lbs / lbs /4-20 1/ lbs / / lbs / / lbs /8-16 3/ ,000 lbs /2-13 5/ ,000 lbs /8-11 3/ ,000 lbs 4 Torque (N.m.) MTRI M N M ,558 N M ,558 N M ,895 N M ,790 N M ,680 N 4 STINLSS STL /4-20 1/ t. Lbs 800 lbs / / t. Lbs 800 lbs M6 4mm 1.01mm 15.86mm 4.75mm 11.2mm 7.80mm 8.50(N.m.) 3,558.lN M8 5mm 1.01mm 20.60mm 6.35mm 15.0mm 10.15mm 11.30(N.m.) 3,558.lN 4 Knife dge lamps Knife dge lamps can be used instead of the original brass hex clamps for clamping rough cut stock, castings and any material that requires a hardened clamping element. Same G dimension as Original ixture lamps above. 4 Max. Holding Number Torque orce of lamps Number G (t/lbs) (Lbs) Per Pack INH /8-16 3/ , /2-13 5/ , /8-11 3/ ,000 4 (N.m.) (N.) MTRI M10 7M M12 8M M16 12M Not designed for clamping hardened material at maximum torque.

5 Series-9 lamps This adjustable low profile, cam action clamp provides clamping of different size workpieces merely by rotating the clamp to one of its other edges. The clamps are.394 (10mm) high and use a 1/2-13 (M12) cam screw. ach of the six clamping surfaces is a different distance from the centerline by.0394 (1mm) as shown in the chart. Therefore, one Series-9 lamp can hold parts that vary up to.240 (9.4mm) simply by rotating the clamp to a different clamping surface. Serrated or smooth edges Heat treated and plated 4,000 lbs. (17800 N.m.) holding force TORQU VLUS N HOLING OR Number Screw Size Max. Torque/Holding orce INH / t Lbs / 4000 Lbs MTRI M12 88 N.m. / 17,800 N. Number istance Inch Metric escription ace Number from L (metric) Smooth (12mm) Serrated (13mm) (14mm) (15mm) (16mm) (17mm) Smooth (18mm) Serrated (19mm) (20mm) (21mm) (22mm) (23mm) Number istance Inch Metric escription ace Number from L (metric) Smooth (24mm) Serrated (25mm) (26mm) (27mm) (28mm) (29mm) Smooth (30mm) Serrated (31mm) (32mm) (33mm) (34mm) (35mm) Machinable ixture lamps These clamps, with the machinable steel washers, provide more flexibility for holding round or unusual shaped parts. s can be held directly to the fixture plate surface or elevated for through drilling. special screw is provided with each package to hold the washer in the proper place during machining. G The flat edge is the same location as H our original fixture clamps. It can be used where a stronger clamping surface is required. Low profile Made of mild steel for machinability Max. Holding Number Torque orce of lamps Number G* H (t/lbs) (Lbs) Per Pack INH /4-20 1/ /8-16 3/ , /2-13 5/ , /8-11 3/ ,000 4 (N.m.) (N.) MTRI M6 4M M10 7M M12 8M M16 12M G* - mount of machinable stock H - The distance to drill & tap hole from edge of workpiece to use flat face. very package includes one machining screw 5

6 Uniforce lamps The compact, economical MIT-IT Uniforce lamp enables you to fixture more parts on the machine table. The specially designed steel wedge spreads the clamping force uniformly on both sides of the 7075-T6 aluminum channel. Increases production Minimizes tool changes Holds two parts with equilateral clamping action Ideal for clamping flat or round workpieces Reduces wasted space See Locating Rails on page 28 asily mated to hydraulic pull cylinders Ideal for pallet changers 1 * Max. Holding Number Thread Maximum Torque orce of lamps Key Number Model 1 * Size Spread (t/lbs) (Lbs) Per Pack Size INH / / / / , / / , / / , / / , /2 (N.m.) (N.) MTRI M M M M M M M * - milled slot wider than dimension will insure clamp remains in line with workpiece. lamp sides should not come in contact with slot walls during expansion. - The distance needed between workpieces for clamp clearance. rill and tap mounting hole on the center of dimension. Long Length Uniforce hannel & Steel Number Model hannel Steel hannel Steel hannel Steel hannel Steel Number Model hannel Steel hannel Steel hannel Steel This material is available in 20" (508mm) lengths so clamps can be fabricated in different lengths to suit any requirement. oes not include plating or drilled holes. 6

7 Machinable Uniforce lamps The compact MIT-IT Uniforce clamp is available with extra material on the clamping jaws so it can be machined to conform to the shape of your workpiece - enabling you to fixture unusual applications easily. The specially designed steel wedge spreads the clamping force uniformly on both sides of the 7075-T6 aluminum channel. The locking plate properly expands the clamp, while making it rigid for machining. Machine to a slip fit of workpiece. lamp retracts after removing locking plate to make it easy to load parts. Note: Locking plate is used only to machine jaws, remove to clamp workpiece. When clamp is used to hold flat stock, use locking plate to machine faces parallel. Patent #6,126,159 I H G Max. Holding Torque orce Model No. escription No. escription * G H** I (t/lbs) (Lbs) INH With Locking Plate No Locking Plate With Locking Plate No Locking Plate / , With Locking Plate No Locking Plate / , With Locking Plate No Locking Plate / , With Locking Plate No Locking Plate /4-20 5/ ,000 (N.m.) (N.) MTRI With Locking Plate No Locking Plate M2 M With Locking Plate No Locking Plate M4 M With Locking Plate No Locking Plate M4 M With Locking Plate No Locking Plate M5 M With Locking Plate No Locking Plate M6 M * - The distance needed between workpieces for clamp clearance, drill and tap mounting holes on the center of "" dimension. - The amount of machinable stock on jaws. H** - Mounting screws included. LONG LNGTH MHINL UNIOR LMPS Locking plate is required to machine channel without vibration. (Sold separately, see Replacement s, page 36) I H This material is available in 7 1/2 (508mm) lengths so clamps can be fabricated in different lengths to fit specific requirements. oes not include plating or drilled holes. Max. Torque Holding Number Model * H I (t/lbs) orce (Lbs) INH hannel Steel Slug hannel / , Steel Slug hannel / , Steel Slug hannel / , Steel Slug 7.50 (N.m.) (N.) MTRI hannel mm M2 M hannel mm M4 M hannel mm M4 M hannel mm M5 M * - The distance needed between workpieces for clamp clearance, drill and tap mounting holes on the center of dimension. - The amount of machinable stock on jaws. (3) rive Screws and (4) Mounting Screws included. 7

8 OK-VIS lamps THR-IMNSIONL MHINING ue to a low-profile design of OK-VIS lamps, it is possible to execute flexible three-directional machining of workpieces with one fastening. This ability to machine a workpiece in three planes means improved accuracy. PULL OWN TION The single wedge clamps keep the workpieces steadily in place, not allowing upward or downward movement. The double-wedge clamps generate a pull-down action pressing the workpieces towards the fixture base. MHINL JWS Single-wedge clamps are also available with extended jaws that can be machined to suit the geometry of the workpiece. SPIL MOL OK-VIS low-profile clamp with a self adjusting steel ball is helpful when clamping castings and workpieces of an irregular shape. 8

9 OK-VIS lamps SINGL-WG OK-VIS LMPS Strong lateral clamping with a single wedge design. Mounting Max. Pressing Hardness Screw Torque orce of of Jaws Number Model Min. Optimum Max. (included) (t/lbs) Jaws (Lbs) HR 47100* K2-VT-SO x 3/4 7 2, * K2-VT-S /16-18 x 3/4 30 5, K2-VT /16-18 x 3/4 30 5, K2-VTI /2-13 x 1 1/ , K2-VT /8-11 x 1 1/ , *47100 and have smooth jaws. OUL-WG OK-VIS Increased clamping force and the double wedge design pulls the workpiece down. Mounting Max. Pressing Hardness Screw Torque orce of of Jaws Number Model Min. Optimum Max. 1 (included) (t/lbs) Jaws (Lbs) HR K2-WTI /2-13 x 1 1/ , K2-WT /8-11 x 2 1/ , MHINL SINGL-WG OK-VIS LMPS dditional material is added to these machinable jaws. Mounting Max. Pressing Hardness Screw Torque orce of of Jaws Number Model Min. Optimum Max. (included) (t/lbs) Jaws (Lbs) HR 47120* K2-VT-S /16-18 x 3/4 30 5, K2-VTI /2-13 x 1 1/ , K2-VT /8-11 x 1 1/ , *47120 has a smooth jaw. SPIL MOL OK-VIS LMPS The hard pivoting ball is ideal for clamping castings and unusual shaped pieces. Mounting Max. Pressing Hardness Screw Torque orce of of Jaws Number Model Min. Optimum Max. G (included) (t/lbs) Jaws (Lbs) HR K2-VT /16-18 x 3/4 30 5, K2-VTI /2-13 x 1 1/ ,

10 Pitbull lamps The revolutionary Pitbull lamp remains the lowest profile, highest holding force clamp in the industry today. High vertical and horizontal clamping forces are generated, considering the size of the Pitbull lamps. It uses a standard cap screw and an oil resistant O-ring. The Pitbull lamp is available in 5 sizes and several styles, a tool steel knife edge for aggressive stock removal, a tool steel blunt edge for general purpose and a brass version to help prevent marring the workpiece. See Locating Rails on page 28. Unique features of Pitbull lamps: xtremely low bite Positive down force High resistance to rip-out Simple, sturdy, high quality design and components 10 PTNT NO Photo courtesy of Gain maximum tool access to your work Virtually eliminate lost work

11 Pitbull Installation reating ixtures is asy... Simply: 1. Machine a slot for the Pitbull lamp 2. rill and tap a hole for the cap screw 3. ssemble the clamp as shown in diagram below 4. Position clamp as shown in diagram and loosely screw to fixture 5. Insert workpiece and tighten cap screw See Locating Rails page 28. lamp Max. Holding No. lamps Width Screw Torque orce Total Per Number escription * Size (t/lbs) (Lbs) Throw Package INH Tool Steel, Knife dge Tool Steel, lunt dge rass, lunt dge Tool Steel, Knife dge , Tool Steel, lunt dge , rass, lunt dge Tool Steel, Knife dge / , Tool Steel, lunt dge / , rass, lunt dge / Tool Steel, Knife dge / , Tool Steel, lunt dge / , Tool Steel, Knife dge / , Tool Steel, lunt dge / , (N.m.) (N.) MTRI Tool Steel, Knife dge M Tool Steel, lunt dge M rass, lunt dge M Tool Steel, Knife dge M Tool Steel, lunt dge M rass, lunt dge M Tool Steel, Knife dge M Tool Steel, lunt dge M rass, lunt dge M Tool Steel, Knife dge M Tool Steel, lunt dge M Tool Steel, Knife dge M Tool Steel, lunt dge M * - Minimum clamp height KNI G LUNT G IXTUR XMPLS oth versions of the tool steel clamps generate the same clamping pressure. However, the Knife dge clamps bite into the material for more aggressive machining, while the lunt dge is less likely to mark the workpiece. PTNT NO

12 Machinable Pitbull lamps The popular Pitbull ixture lamp is now available in a machinable version. The clamp has positive down force and a very low gripping profile, making it well suited for machining pieces complete in one set up. The Machinable Pitbull lamp is made of tool steel and heat treated to about 43R for long life, yet still machinable. There is additional material on the clamping face to allow for machining a radius. It is available in two sizes with 6,000 and 12,000 lbs. (26000 and N) of holding force. dowel pin is included in each package to locate clamp while machining radius. Tighten clamp on dowel pin for proper location for machining clamp. Remove pin and install o-ring to clamp workpiece. Maximum recommended stock removal from centerline of clamp: = =.180 (56077 = 1.5mm) (56088 = 4.5mm) lamp Screw Max. Total Holding owel No. lamps Per Number escription * Width Size Torque orce Throw Pin Package INH Tool Steel, Machinable / (t/lbs) 6,000 (Lbs).050 1/ Tool Steel, Machinable / (t/lbs) 12,000 (Lbs).075 1/4 2 MTRI Tool Steel, Machinable M (N.m.) (N.) Tool Steel, Machinable M (N.m.) (N.) * - Minimum clamping height Modular Pitbull lamps The Pitbull ixture lamp is very well known for it s low profile and positive down force. It is now available as a modular clamp in two styles. G oth versions are produced in two sizes with holding forces of 3,600 and 6,000 lbs (16000 and N). The slotted Modular Pitbull lamp with a step offers increased versatility through its unique riser design. This clamp supports the workpiece off the machine table for through milling and drilling. The hardened and ground clamps are designed for use on work cubes, as well as machined tables with tapped holes or T-slot configurations. H* The compact Modular Pitbull lamp is ideal for clamping workpieces in series by using the back surface of a clamp to locate the next workpiece. The back of the clamp is ground square to the bottom for precise location of parts. The height of the clamp can be adjusted by the depth of the milled slot used to locate the clamp. 12 Number Max. Holding Knife lunt Torque orce Mounting dge dge escription G H* (t/lbs) (Lbs) Screw Slot INH Medium/ompact N ,600 5/ Large/ompact N ,000 3/ Medium/Slotted ,600 1/2 losed Large/Slotted ,000 5/8 losed (N.m.) (N.) MTRI Medium/ompact N M Large/ompact N M Medium/Slotted M12 losed Large/Slotted M16 losed H* - lamp travel PTNT NO

13 Multi-ixture lamps and Stops pplications without steps pplications with steps The Multi-ixture lamps, with a step, offer increased versatility through their unique riser clamp design. These clamps support the workpiece off the machine table for through milling and drilling. The Multi-ixture lamps, without a step, grip the workpiece at a higher point for more clamping strength and better stability. The hardened and ground clamps offer quick cam action clamping and are designed for use on work cubes and machine tables with tapped holes or T-slot configurations. They adjust to unusually shaped parts because the cam action allows the clamping element to always make maximum contact with the workpiece for greater holding force. The tilted clamping element provides positive down force for more accurate machining. With Steps cam Max. Holding Mtg screw Torque orce Screw Number Item G H (t/lbs) (Lbs) (not incl) Slot INH WITH STPS lamp ,000 5/16 losed Stop N N N 5/16 losed lamp ,000 1/2 losed Stop N N N 1/2 losed lamp N ,000 5/8 Open Stop N N N N 5/8 Open WITHOUT STPS lamp N N ,000 5/16 losed Stop N N N N N 5/16 losed lamp N N ,000 1/2 losed Stop N N N N N 1/2 losed lamp N N 1.82 N ,000 5/8 Open Stop N N 1.82 N N N N 5/8 Open H H G lamp losed lamp Open Without Steps G Stop losed Stop Open (N.m.) (N.) MTRI WITH STPS lamp M8 losed Stop N M8 losed lamp M12 losed Stop N M12 losed lamp N M16 Open Stop N N M16 Open WITHOUT STPS lamp N N M8 losed Stop N N N M8 losed lamp N N M12 losed Stop N N N M12 losed lamp N N 46.2 N M16 Open Stop N N 46.2 N N M16 Open H H G lamp losed lamp Open G Stop losed Stop Open 13

14 I Xpansion lamp The I Xpansion clamp is the ideal solution to hold parts on an inside diameter for high density machining on vertical or horizontal machining centers. It can also be used as an expanding mandrel on a lathe. These machinable clamps are produced in 12 sizes and can hold internal diameters from under 3/16 to almost 10 inches (4.1 to over 103mm). The flange diameter of the clamp is held to a close tolerance for precision locating in a machined pocket on work cubes and fixture plates. The customer machines the mild steel clamp to match the bore of the part ensuring a proper fit. Often times the clamps can be remachined for different size jobs. The low profile I lamp can hold several parts in one compact area for secondary operations without any clamping interference. They are quickly tightened with a hex key, torque driver or can be mated to hydraulic pull cylinders for automation. lamping and locating mill parts on two bores. Low profile Ideal for secondary operations on lathe parts asily machined to size on lathe or mill xcellent for palletized setups llows more parts per workcube or fixture plates Heat-treated and coated screw for long life lamp body made of mild steel for machinability Tighten with hex key or hydraulic pull cylinders Longer screws for hydraulic applications available Innovative application. 14

15 I Xpansion lamp Machining and Installation Model #00 - #6 I Xpansion lamps xpand clamp approximately.002 to.003 (.1mm) over relaxed diameter and machine to fit workpiece bore, either on lathe or mill. If machining the clamp on a lathe use the nut provided, on the back of the clamp, to tighten the tapered screw. This nut is used only while machining the clamp. Machine a pocket in the fixture, for the close tolerance dimension and drill and tap mounting holes per H column. rill and tap a hole from the I column in the center of the pocket for the tapered screw. recessed dowel pin may be installed into the flange for additional rigidity if required. Range of expansion.005 to.025 (.2 to.5mm) depending upon size. Model #7 - #10 I Xpansion lamps Locking ring provided to ensure segments remain rigid while machining clamps to size. Insert ring and tighten drive screw, machine clamp to bore size. Remove ring to clamp workpiece. ggressive material removal is not recommended when machining clamps to size. G H I J Model Max. Torque Holding Number Number G H* I J (t/lbs) orce (Lbs) INH # on.540 H # on.825 H # on.910 H 1/ , # on H 5/ , # on H 3/ , # on H 1/ , # on H 5/ , # on H 5/ , # /4-20 on H 5/ , # /4-20 on H 5/ , # /4-20 on H 5/ , #10 ** /4-20 on H 5/ , (N.m.) (N.) MTRI # M2 on 13.7 H M # M3 on H M # M3 on 23.1 H M # M3 on 29.0 H M # M4 on 39.4 H M # M4 on 45.5 H M # M5 on 55.9 H M # M5 on 63.9 H M # M6 on 92.6 H M # M6 on H M # M6 on H M #10 ** M6 on H M G - Minimum diameter the dimension can be machined or turned down to. H* - (3) Mounting Screws included - (4) for model numbers #9 and #10. **Model #10 Made from 7075-T6 aluminum. 15

16 Side-Loc Xpansion lamp The Side-Loc Xpansion lamp is actuated from the side, making it perfect for blind hole applications. It s produced for both mill and lathe applications. The cam shaft and plunger expands the clamp from the side. Same mounting dimensions as our original I clamp. The Side-Loc Xpansion lamp is actuated by turning a socket head cam shaft on the side, which moves a tapered plunger to expand the clamp. The locking ring provides an accurate preset diameter and rigidity for machining. Maximum torque on locking ring 10 ft. lbs. (13 N.m.). Like our original I Xpansion clamps, the Side-Loc Xpansion lamp has the dead length feature which is critical for close tolerance dimensions. The Side-Loc Xpansion lamp is designed in two styles: one for milling operations and one for lathe applications. One size is available for each model. The mill Side-Loc Xpansion lamp can be machined from to.710 (28.4 to 18mm) and the lathe version from 2.09 to.710 (53 to 18mm). The lathe version has a 1 (25mm) straight shank. H Lathe Version Mill Version G H 16 Model Hex Max. Torque Holding Number No G H* Key (t/lbs) orce (Lbs) INH Mill # on H M6 49 4, Lathe # N M6 49 4, (N.m.) (N.) MTRI Mill # M4 on 39.4 H M Lathe # N/ M G - Minimum diameter the dimension can be machined down to. H* - (6) mounting screws included.

17 Manual ctuators for Mills and Lathes Mitee-ite Products introduces another new and innovative workholding system. Specifically designed to clamp on lind I s smaller than our Side-Loc clamps would allow, for both Mill and Lathe applications. We took the design a step further increasing the functionality to clamping smaller inside diameters, and for the Mill version the option of holding the workpiece in a vertical or horizontal plane. y simply mounting our standard I Xpansion clamps (Model #00 thru #4) on these manual actuators, or using another style clamp that has a straightdraw, you can now perform operations that previously required expensive hydraulic/ pneumatic pull cylinders. Number ylinder Mill Lathe Thread M M M M M M12 Mill Version 2.25 (57.15mm) Lathe Version 1.00 (25.4mm) 1.5 (38mm) Threaded ylinder 2.25 (57.15mm) 1/4-20 (M6) esigned for Mounting olts 1.00 (25.4mm) (56.9mm) ctuator rive Screw with Retaining Snap Ring The actuators are available with heat-treated cylinders tapped for the following drive screws: M2, M4, M6, M8, M10, M12 M6 Hex Key Number

18 yna-orce lamps The majority of the yna-orce clamp is below the surface of the fixture which provides excellent clamp support and makes for a very low profile. The clamp jaw slides on an angle for positive downforce. Incredible clamping and hold down power Low profile, compact design 17-4 PH stainless steel Smooth or serrated jaws The support surface of the yna-orce clamp can be installed flush with the fixture plate or raised to hold the workpiece off the fixture, enabling drill through. Use our TalonGrip Grippers opposite the yna-orce lamps for extremely low profile applications when high holding forces are needed. See page 22 for Gripper information. G 18 lamp Jaw G lamp rive Key Max. Number & Hardness * Min Optimum Max Travel Screw Size Torque Holding orce Smooth 34R Serrated 44R Smooth34R Serrated 44R Smooth 34R Serrated 44R mm 5mm 7.3 (t/lbs) (N.m) 2,000 (Lbs) (N.) mm 6mm 17.6 (t/lbs) (N.m) 2,600 (Lbs) (N.) mm 8mm 35.3 (t/lbs) (N.m) 3,200 (Lbs) (N.) * - ody diameter - Smooth jaw only will have relief cut

19 yna-orce Installation 1. ore L of the hole L distance from edge of workpiece. 2. rill and tap H to mount clamp in pocket. 3. Machine counter bore if recessing clamp into fixture. 4. Provide a back stop to locate the part. See Locating Rails on page 28. I J NOTS: 1. "N*" - To have rest pad flush with fixture, use the dimension provided. To have the rest pad above the fixture surface, reduce the depth accordingly. 2. or dimensions I and J, use a tolerance of +.1/-0mm. or dimension L and O, use +.1/-.1mm. O N* K (4 times) H M L Workpiece Workpiece Section - HIGHT O JW IN RLTION TO L O OR ROM G O WORKPI. Height of Jaw 20mm 25mm 30mm G L L L XMPL: 20mm clamp when L of bore is 4.90mm from edge of workpiece (L - see drawing on left): jaw height is 5.00mm (G - see drawing on page 18). Number H I J K L M N O M5 or M5 or M6 or 1/ M6 or 1/ M8 or 5/ M8 or 5/ PTNT NO

20 Vacmagic VM100 VM100 ase Unit (45375) with VM300 Vacuum Pallet (45150) VM100 ase Unit (45375) in Vise VM100 ase Unit (45375) on a Magnetic huck The Simplest and Most Versatile Vacuum System on the Market The VM100 was primarily designed for grinding non-ferrous material on a magnetic chuck. uring the early stages of R & it was discovered the VM100 could be much more. lamp the VM100 in vise to reduce set-up time, use as a pallet changer or mount to a grid plate or T-slot table. The VM100 uses the same patented method as the VM300 to produce a vacuum strong enough for industrial applications but still operates on shop air! No need for vacuum pumps and coolant traps. We include everything necessary to get your VM100 running within minutes of opening the box. Operates on PSI shop air, eliminating vacuum pumps and coolant traps Will accept the standard VM300 Vacuum pallet, increasing your vacuum platform to over 14 x 12 (360mm x 315mm) Make your own vacuum fixtures - we can help with the design and produce the fixture for your custom application Remove 12mm pins when grinding/machining thin material, use set screws to locate and aid in holding force VM100 ase Unit (45375) with a Production Pallet (VM100 lank Pallet ) - Length - Width - Height Number escription Inch (Metric) Inch (Metric) Inch (Metric) VM lank Pallet 12.5 (318mm) (150mm) 1.0 (25mm) VM300 Vacuum Pallet 14.2 (360mm) 12.4 (315mm) 0.63 (16mm) ase Unit with Mounting lamps (315mm) 5.5 (140mm) 1.0 (25mm) omplete System Includes: base unit, 2 blank pallets VM100 lank Pallet VM lank Pallet 14.2 (360mm) 12.4 (315mm) 0.75 (19mm) VM300 Vacuum Pallet 14.2 (360mm) 12.4 (315mm) 0.63 (16mm) VM300 Large Vacuum Pallet (859mm) 14.5 (368mm).625 (16mm) ase Unit (Receiver) (323mm) 13.0 (330mm) (35mm) Includes: safety switch, required hoses omplete System Includes: base unit, 2 blank pallets,1 vacuum pallet 20 Gasket Material (for VM300 & VM100) lack - xcellent for long cycles and aggressive coolants. White - xcellent for small parts, water based coolants or running dry. No. esciption iameter LK Vacuum Gasket - per 5 ft. length Vacuum Gasket - by the foot Vacuum Gasket - per 5 ft. length.125 WHIT Vacuum Gasket - by the foot.170 VM100 ase Unit PTNT NO

21 Vacmagic VM300 The ll-in-one Pallet hanger and Vacuum huck System est Workholding Product at MH xhibition 2006 In a relatively short amount of time the VM300 has established itself as the vacuum system to which all others are measured. apabilities include traditional vacuum applications using our standard grid plate and custom vacuum applications (ie: machining blank pallet to suit specific part geometry) and the ability to perform as a rock solid pallet changer. ontact us to schedule an in-house demonstration with one of our highly qualified Manufacturing Representatives. Two VM300 ase Units (45175) and large Vacuum Pallet (45160) Simple design keeps cost low Quick-change - swap pallets in 30 seconds or less Productivity maximized - load pallets while machining asy to install and set-up Precise repeatability Reliable and easy to use - virtually maintenance free lexible pallet design - limited only by your imagination! No pumps - uses standard shop air One Small Investment = Huge Payoffs! VM300 lank Pallet VM300 ase Unit (45175) with a Production Pallet (VM300 lank Pallet ) Reference chart on page 20 Workpiece placed over gasket and pushed down to create a vacuum. Now ready for machining. (VM300 Vacuum Pallet ) VM300 ase Unit PTNT

22 TalonGrip Vise Jaws Mitee-ite Products introduces a new and innovative product that will increase the functionality of your standard 4 and 6 inch (100mm and 150mm) vises. TalonGrip is a simple bolt on system that will allow you to perform aggressive machining operations while clamping on as little as.060 (1.5mm) of an inch. Ideal for small lot sizes, difficult applications or proto-type work when building a fixture would not be beneficial. TalonGrips are also available individually for fixturing with Pitbull and yna-orce lamps or for soft jaw applications. Vise Jaw with Mounting Holes ggressive stock removal Grip (Grips R) Vise Jaw without Mounting Holes 22 Multiple parts ixture application with Pitbull lamps Soft jaws Steel Vise Jaw Set (Set includes 4 TalonGrips, 1 stop with M5 screws) Number Vise (metric) (metric) (metric) (metric) (metric) e (metric) WITH MOUNTING HOLS (100mm) 4.0 (100) 1.48 (37.59) 1.0 (25.4) 2.5 (63.5).688 (17.47) /6 (100mm/150mm) 6.0 (150) 1.73 (43.94) 1.0 (25.4) 2.5/3.88 (63.5/98.55).688/.94 (17.47/23.87) (150mm) 8.0 (200) 1.73 (43.94) 1.0 (25.4) 3.88 (98.55).94 (23.87) WITHOUT MOUNTING HOLS (100mm) 4.0 (100) 1.48 (37.59) 1.0 (25.4) /6 (100mm/150mm) 6.0 (150) 1.73 (43.94) 1.0 (25.4) (150mm) 8.0 (200) 1.73 (43.94) 1.0 (25.4) - - VIS JW Grips & Stops R recommended No. of Grips No. escription Gripping Height Per Pack INH xtra Grips xtra Stop MTRI xtra Grips M5 1.5mm-1.9mm xtra Stop M5-1 ixture Grips R recommended No. of Grips No. a Gripping Height Per Pack INH / MTRI M5 1.5mm-3.0mm M5 1.5mm-3.0mm M8 1.5mm-5.6mm 1

23 VersaGrip Vise Jaws VersaGrip, as the name implies, offers the versatility of clamping standard vise work as well as providing a solution for difficult applications that would normally require fixturing or machining soft-jaws. y simply replacing your current jaws with the VersaGrip system you can securely hold odd shaped parts while machining at speeds and feeds you never thought possible. Large dimensions Odd shaped parts This system can accommodate a wide range of part sizes as well as holding multiple parts in a single cycle. The hardened (52-54 R) VersaGrip has penetrating teeth designed to bite into your workpiece preventing lateral and horizontal movement. These grips will hold flame cut parts, castings, even parts with a negative draft! Vise Jaw with Mounting Holes Multiple parts Tombstone application Vise Jaw without Mounting Holes STL VIS JW ST (Set includes 4 VersaGrips ) Number Vise (metric) (metric) (metric) (metric) (metric) e (metric) WITH MOUNTING HOLS /6 (100mm/150mm) 6.00 (150) 1.88 (47.75) 1.0 (25.4) 2.5/3.88 (63.5/98.55).688/.94 (17.47/23.87) (150mm) 8.00 (200) 1.88 (47.75) 1.0 (25.4) 3.88 (98.55).94 (23.87) WITHOUT MOUNTING HOLS (150mm) 8.00 (200) 1.88 (47.75) 1.0 (25.4) (200mm) 8.00 (200) 1.88 (47.75) 1.0 (25.4) - - versagrip R recommended No. of Grips No. Gripping Height Per Pack (19.05).375 (9.52) M (1.55mm-3.5mm) 2 23

24 Lean MM Workholding System Mitee-ite Products is pleased to introduce another new and innovative product line that is designed to improve your productivity in the Q department! The Lean MM Workholding System is the most costeffective solution in today s market. Simple, one-finger operation and quick adjustments allow you to process parts through inspection faster than ever before. liminate costly bottlenecks in the inspection room. Quick part change-over increases productivity and profits asily design universal fixtures for multiple jobs Non-marring material protects your work Low-profile, simple designs stay out of your way Includes 5S-ready packaging! We have a bottleneck in our Q department because our new Palletech machines produce parts faster than we can inspect - even with our automated MMs. The action of these new clamps helps us inspect parts faster, boosting productivity of both machines. We re able to verify the quality of more parts early in production. Scott errecchia, Vice President, Lincoln Tool & Machine, Hudson, M Silver-ullet and Trigger-inger Simple-Stop -lock and ross-ow Trigger-lock Open-Sight ixture Plate 24 Number* Inch Metric Model escription Lean Kit 80+ Pc Kit includes: (4) Trigger-inger, (4) ross-ow, (8) -lock, (3) Trigger-lock, omplete with foam drawer inserts (4) sets Silver-ullet, (2) 7 pc. set Simple-Stop. Plus thumb screws, button head screws, and foam drawer inserts! xtra-lean Kit 162+ Pc Kit includes: (8) Trigger-inger, (8) ross-ow, (16) -lock, (6) Trigger-lock, omplete with foam drawer inserts (8) sets Silver-ullet, (4) 7 pc. set Simple-Stop. Plus thumb screws, button head screws, and foam drawer inserts! MM Trigger lock (3 pk) MM Trigger-inger (4 pk) 4 set module/stackable MM ross-ow (4 pk) MM -lock (8 pk) MM Silver-ullet (4 ea pcs) 1, 2, 3 Size Standoffs MM Simple-Stop 7 pc. Set of Rails & Stops omparator ixture Plate 5 x14, omparator Plate, 1/2 aluminum, 1/4-20 thread, 1/2 spacing MM ixture Plate 10 x10 10 x10 (254x254mm), 1/2 aluminum, 1/4-20 thread, 1/2 spacing MM ixture Plate 20 x28 20 x28 (508x711mm), 1/2 aluminum, 1/4-20 thread, 1/2 spacing MM ixture Plate 26 x40 26 x40 (660x1000mm), 1/2 aluminum, 1/4-20 thread, 1/2 spacing Open-Sight Vision ixture Plate 8 x 8 (203x203mm), 1/2 acrylic, 1/4-20 thread, 1/2 spacing Open-Sight Vision ixture Plate 8 x 10 (203x254mm), 1/2 acrylic, 1/4-20 thread, 1/2 spacing Open-Sight Vision ixture Plate 8 x 12 (203x305mm), 1/2 acrylic, 1/4-20 thread, 1/2 spacing Open-Sight Vision ixture Plate 12 x 16 (305x406mm), 1/2 acrylic, 1/4-20 thread, 1/2 spacing *Inch: 1/4-20 threads, Metric: M6 threads Trigger-inger, -lock, ross-ow, Silver-ullet, Trigger-lock, Simple-Stop, Open-Sight are registered trademarks. PTNT PNING

25 ompact Toe lamps This cam action fixture clamp provides positive down force while using very little space on a fixture. Workpieces can be clamped in series by using the back surface of a clamp to locate the next workpiece. The hardened steel clamping element has both a smooth surface for machined workpieces and a serrated clamping surface for rougher work. The height of the clamp can be adjusted by milling the slot deeper in the fixture plate. Total Mounting Max. Holding am istance of Screws Torque orce Number G H I* Screw Movement (Included) (t/lbs) (Lbs) INH # /16-18x3/4 LHS , # /8-16x3/4 LHS , # /2-13x11/4 SHS ,000 (N.m.) (N.) MTRI # M # M # M The distance needed between the front of the clamp base and the workpiece. I* - The distance from the top of the washer to the bottom of the clamp body. rill and tap the centerline of for mounting holes. T-Slot Toe lamps This clamp is like the ompact Toe lamp, only it is designed to be used in the T-slots of machine tables. It provides 4,000 lbs. (17800 N) positive down force while maintaining a low profile. The hardened steel clamping element has both a smooth surface for machined workpieces and a serrated clamping surface for rougher work. Max. Torque/ Holding orce 1 2 (t Lbs/Lbs) INH /4,000 (N.m./N.) MTRI / The distance from the top of the back of the washer to the bottom of the clamp body. 2 - The distance from the top of the front of the washer to the bottom of the clamp body. Number T-slot Size INH No T-nut or Mtg. Screw / / / /4 MTRI No T-nut or Mtg. Screw (with mtg screw) Torque mounting bolt to 110 t/lbs (150N.m.). 25

26 T-Slot and dvant-dge lamps The original MIT-IT T-Slot lamp combines our unique cam action clamping element with a T-nut. Locks in machine T-slot for low profile clamping Makes fast set-ups possible right on the machine table rass hex follows contour of unusual shaped parts Packaged in pairs or complete kits The Mitee-ite Kit ontains: 4 Mitee-ite T-Nuts 6 Mitee-ite ixture lamps 2 Hex Keys MIT-IT T-SLOT KITS Max. Holding am T-Slot Torque orce Number Screw Size G H I J (t/lbs) (Lbs) INH /4-20 3/8 1/ / /16 3/ /8-16 1/2 3/ , /8-16 9/16 3/ , /2-13 5/8 5/ , / /16 5/ ,000 Max. Holding am T-Slot Torque orce Number Screw Size G H I J (N.m) (N) J G H T-SLOT LMPS I Top View MTRI M6 x mm 5mm , M6 x mm 5mm , M8 x mm 5mm , M10 x mm 7mm , M12 x mm 8mm , M12 x mm 8mm , M16 x mm 12mm , M16 x mm 12mm ,680 Number Holding T-Slot of lamps orce Number Size Per Pack (Lbs) Number Holding T-Slot of lamps orce Number Size Per Pack (N) VNT-G LMPS INH / / /2 2 2, /16 2 2, /8 2 3, /16 2 3,000 Hex key not included. MTRI mm 2 3, mm 2 3, mm 2 3, mm 2 8, mm 2 13, mm 2 13, mm 2 26, mm 2 26,680 The MIT-IT dvant-dge lamp provides additional clamping force and improved table grip. Tilted clamping element creates a positive downward force and 4,000 lbs. holding force Hardened clamping element has both a smooth surface for machined workpieces and a serrated clamping surface for rougher work Improved locking mechanism secures clamp to machine table Packaged individually (52224) or as kit of two (52424) Max. Torque/ am T-Slot Holding orce Number Screw Size G H I (t Lb/Lbs) INH # /8 5/ /4, (kit) Top View I (N.m./N.) 26 MTRI IMNSIONS /17800 Torque mounting bolt to 70 t/lbs (150N.m.). H G

27 Vise Pallet Now you can run fixture jobs without removing your vises. Vise Pallets are designed to fit in all 6 inch (150mm) vises and measure approximately 6x8 and 6 x 10 inches (150 x 203mm and 150 x 254mm). Ideal for multiple small parts using one of several MIT-IT low profile edge clamps. The Vise Pallets are qualified in 2 places so they can rest on parallels or on the top of the jaws. HOW TO US The MIT-IT Vise Pallet has a locating pin that makes contact with the left side of the solid jaw for repeat location of pallet. Simply slide pallet to the right of the vise and clamp in place. Pallets can be machined and tapped as required. Number (metric) (metric) (metric) (metric) (150) 8.00 (203).95 (24.4).44 (11.2) (150) (254).95 (24.4).44 (11.2) 27

28 Locating Rails for Jigs and ixtures Is it taking too long to make a fixture to increase production? MIT-IT Products makes fixture building easier and quicker with the addition of ready made locating rails. Rails are made of low carbon steel, then ground square. They are easily machined when used with our machinable clamps. arbinite coating can be added to increase holding force (See carbinite.com for more information). Locating rails are made of low carbon steel and are precision ground square. They are available in a number of sizes and lengths to suit most applications. Multiple rails can be used in line for long workpieces or to hold more than one piece in a row. owel pins can be used for end stops. No. Number +/ G Holes INH N.N 1/ / / / / / / / / / / / / / / Locating Rail Installation 1. Mill a slot to locate the rail. epth of the slot will determine rail height. 2. rill and tap the required holes to mount the rail. 3. or better rigidity, the rail should be pinned to the fixture plate with dowel pins. 4. If rails are to be machined to hold round pieces, the clamps should be mounted and both rail and clamp machined at the same time No. Number G Holes MTRI M6 11mm M6 11mm M6 11mm M6 11mm M10 18mm M10 18mm M10 18mm 5 Mounting Screws included. 28

29 luminum Sub Plates xtruded luminum Sub Plates are available in standard sizes in stock or in custom lengths to order. Standard sizes are premachined to.005 (.13mm) flatness and parallelism per foot (300mm). I G H Number x x (metric) T-slots (metric) (metric) (metric) G (metric) H (metric) I (metric) Lbs. (KG) x 13.0 x 1.48 (228 x 330 x 38) 3 5/8 (16) 2.00 (50.8) 2.50 (63.5).49 (12.7).50 (12.7).50 (12.7) 13.3 (6.1) x 18.0 x 1.48 (228 x 457 x 38) 3 5/8 (16) 2.00 (50.8) 2.50 (63.5).49 (12.7).50 (12.7).50 (12.7) 18.5 (8.5) x 24.0 x 1.48 (228 x 610 x 38) 3 5/8 (16) 2.00 (50.8) 2.50 (63.5).49 (12.7).50 (12.7).50 (12.7) 24.8 (11.3) USTOM LNGTHS Number (metric) (metric) (metric) (metric) (metric) G (metric) H (metric) I (metric) (228) 1.48 (38) 5/8 (16) 2.00 (50.8) 2.50 (63.5).49 (12.7).50 (12.7).50 (12.7) Subplates can be ordered in lengths up to 55 (1397mm), not machined. The last two digits of the part number should be the length of the plate in inches. Mounting lamps Mounting clamps are designed for securing MIT-IT luminum Sub Plates, Vacmagic and many types of machine vises Screw Number Size (metric) (metric) (metric) (metric) (metric) (metric) 22810* 1/2 (M12) 1.25 (31.8) 1.50 (38.1).87 (22.1).35 (8.9) 1.10 (28.0) 22815** 1/2 (M12) 1.25 (31.8) 1.50 (38.1) 1.25 (31.8).44 (11.2) 1.10 (28.0) *or Vacmagic VM100 **or Vacmagic VM

30 hip Hooks The chip hook is an essential safety tool for all shops. These galvanized steel hooks are fitted with a protective polyethylene hilt and wooden handles to ensure a firm grip. vailable in several lengths and single or double handles. Single Handle Hook with Protecting Hilt Held in one hand, flexible mounted guard ouble Handle Hook with Protecting Hilt Held in two hands flexible mounted guard STY! work related accident can happen very easily. lways use a chip hook to clear away annoying chips and empty the chip trays on your machines. Number escription (metric) (metric) (metric) (metric) SINGL HNL hip hook, single handle (400) 7.0 (180) 22.5 (570) 7.0 (180) hip hook, single handle 20 (500) 7.0 (180) 26 (670) 7.0 (180) OUL HNL hip hook, double handle 20 (500) 13 (320) 32 (820) 7.0 (180) hip hook, double handle 31.5 (800) 13 (320) 44 (1120) 7.0 (180) hip hook, double handle 39 (1000) 13 (320) 52 (1320) 7.0 (180) Low Profile Gripping Rail These gripping rails are excellent for holding non-ferrous material during grinding and milling on a magnetic chuck. Grinding stainless steel, brass and plastic, while maintaining parallelism, is easy with these gripping rails from Mitee-ite..48 (12.2mm) Longer size parts can be held by using multiple rails. s can be pushed against the solid rail with one or more of the gripping rails (146mm) Number Quantity lamp 30 n increase in the clamping pressure can be achieved by placing additional steel behind the gripping rails Rail Knife dge Rails Knife dge Rail lunt dge Rails lunt dge 2 lamps included with each rail..58 (14.7mm) 1.25 (31.7mm).29 (7.4mm)

31 KOPL Mini lamps These low profile cam action clamps and stops have a holding force of 880 lbs. (3900N.) and have fingers that push the workpiece down before clamping, even on castings that have negative draft! Ground stops are mounted with special screws to ensure high precision locating. M TION LMPS The clamping element rotates around the eccentric that provides for clamping in all directions. lamping range:.047 (1.2mm). Made of spring steel. STOPS/LOTORS The single stop with only one rigid stop is used for pieces over 1.75 (44.5mm) long. The double stop with 2 rigid stops is used for small size pieces. oth are made of spring steel. LOW PROIL LMP RIS LMP lamping Max. Number Height Torque t. Lbs. (2.5mm) (8.95N.m.) lamping Max. Number Height Torque t. Lbs. (7.5mm) (8.95N.m.) SINGL STOP Number Jaw Height OUL STOP Number Jaw Height (2.5mm) (2.5mm) LMPING KY mm RIS SINGL STOP RIS OUL STOP Number Jaw Height Number Jaw Height KOPL MINI LMPS N STOPS Number Item Stop Stop Stop Stop Stop Stop lamp lamp Special mounting screws included Installation instructions and files available online: Miteeite.com (7.5mm) SWIVL STOP Jaw Number Height (2.5mm) (7.5mm) RIS SWIVL STOP Jaw Number Height (7.5mm) 31

32 Kopal lamps Need a quick and easy way to clamp parts on a ridgeportstyle mill? heck out this versatile line-up of clamps! rom the strong but compact Piccolo to the heavy-duty ig lock. The worm and gear design ensures the clamps will not loosen with use yet the clamps are easy to set up and break down. This is ideal for short cycle times and odd shaped parts. The modular design also allows adjusting clamping height by stacking the riser blocks, and the use of an extension arm increases reach! or the complete line of Mono-loc style clamps, see our website: Miteeite.com Piccolo Up to 1460 lbs. (6500N) Holding orce When the arm is released, the Piccolo remains in position in the slot. vailable in a boxed set. Mounted on a T-slot table with a special M8 screw mono bloc Up to 3600 lbs. (16000N) Holding orce 1. Slide the T-nut and the screw into the slot 2. Position and tighten the clamp onto the table using the clamping key provided 3. lamp the workpiece using the same key 4. Proceed with machining Mounted on a T-slot table with a special M10 screw mono bloc chain Up to 3600 lbs. (16000N) Holding orce The 1 meter of chain allows for clamping large workpieces. big block Up to 9000 lbs. (40000N) Holding orce When the workpiece is released, the ig lock can either remain fixed in the slot, or slide in the slot. ases, riser blocks, screws, cylinders and t-nuts are sold separately. UNTRU GRUNPLTT Quick mounting and dismounting Mounted on base and riser block with adaptor and special screw Number Piccolo Standard uty hain ig lock Mono-loc with extension arm increases range to 5 1/ /2 5 5/8 32 NOT: lamping force is reduced when using the extension arm.

33 Kopal lamps RPLMNT SWIVL SHOS Shoes #2 & #3 give you a larger clamping surface. Shoes #4 & #5 are for holding round workpieces. Number Model # # # # Set of all 4 or the complete line of Mono-loc style clamps, see our website: Miteeite.com LUX MONO-LO STRT-UP KIT High-impact plastic storage/ carrying case with room to store above tools, and space to store additional T-nuts for other size mills. INIVIUL MONO-LO ITMS Number escription Standard-uty Mono-loc lamp with 2 5/8 rm (Includes T-wrench) Standard-uty Riser lock Replacement Swivel Shoe T-Wrench for Standard-uty Mono-loc xtension rm Worm Gear Kit includes: (2) standard-duty Mono-loc lamps with 2 5/8 arm, (2) standard-duty Riser locks, (1) xtension rm, (1) standard-duty T-Wrench, (2) M10x35mm screws, (2) M10x40mm screws, (2) T-nuts (choose from (2) chart at right T-Slot Number Size / / / /4 SPIL SRWS N T-NUTS OR MONO-LO (Order one screw and one nut per Mono-loc) Number escription M10 x 35mm Screw for 9/16 T-Nut M10 x 40mm Screw for 5/8 & 3/4 T-Nut M10 x 45mm Screw for 13/16 & 7/8 T-Nut /16 x M10 T-Nut /8 x M10 T-Nut /4 x M10 T-Nut /16 x M10 T-Nut /8 x M10 T-Nut Mono-loc hain lamp The Mono-loc hain lamp is a simple and rapid workholding solution for a wide array of applications. The hain lamp offers fast and powerful clamping with forces to 3,600 lbs. (16000N). dditional lengths of chain can be added for large applications pplication with large cylindrical piece Number escription 25040* Mono-loc hain lamp with Master Link, 5 Protective lips, nchor, Key and 1 Meter of hain Master Link xtra hain (1 meter) nchor Protective lips (5/pk) Wrench *Includes (2) M10 mounting screws for anchor and clamp. T-nuts sold separately - see above To prevent marring or scratching on delicate pieces use the protective chain clips. (25045) Minimum radius 6. 33

34 Strap lamps This low profile design promotes superior clamping in both normal and restricted areas with minimal tooling interference. Heat treated 17-4 P.H. stainless steel Holding Number orce (Lbs) INH /8 ia. PIN 3, /2-13 6, /8-11 8, / ,700 (N.) MTRI ia. Pin M M M ollet Wrenches The MIT-IT ollet Wrench simplifies insertion and removal of collets in the spindle nose on N lathes. The MIT-IT ollet Wrench is manufactured with a steel head and fins for greater strength and durability. The bright red handle makes it easy to locate and is designed to be comfortable to the hand. The collet wrenches are available for 5, 16 and 3J collets. ollet Number Sizes ins J 3J ollet Stop The MIT-IT "front" loading ollet Stop is the most convenient 5 ollet Stop on the market. Once seated, the collet need not be removed for adjustment. Quick changing and easy to use Non clogging design Saves time and money Self centering Perfect for N setups Reusable for different jobs Number Length (metric) (610) 34

35 Mitee-Grip How to Hold a Workpiece When You an t Use a lamp Mitee-Grip is a heat activated wax based compound embedded in precision paper, coated on nylon mesh or in a stick form. This holding media maintains parallelism on precision parts. It is very useful for thin parts, micro machining, optical and quartz components, and jewelry related items. pproximate holding force 40 PSI. The original paper product is excellent for holding smooth flat parts and maintaining parallelism. HOW MIT-GRIP WORKS The mesh product captures additional wax material in the web and aides in holding irregular shape parts. Typically additional holding force can be attained with this material. The stick form material can be used in shallow cavities for holding concave and convex pieces. It will also stabilize delicate parts during machining. Place the Mitee-Grip 1 sheet on the In some cases the part should be subplate leaving a 1/4 (6mm) lightly clamped to prevent movement. border on all sides, or melt stick on 2NOT: Over thin workpieces use a top warm subplate. plate for even pressure. 225 (107 ) is application temperature and fully liquid, (85 ) is solid and becoming liquid. Some customers use an oven and record time and temp once determined by experimentation. hot plate may also be used at higher temps if monitored. Most parts will float when the Mitee-Grip has liquefied. Use air or water to cool, being careful is ready, use coolant while to prevent water from going between machining. Reheat to remove. We have 4subplate and workpiece while hot. 5found an ultrasonic cleaner is best to remove wax residue or simply wipe part while warm using alcohol based cleaner. Number escription Size (Metric) Paper Roll 12 x5 (305 x 1524) Paper Roll 12 x25 (305 x 7620) Mesh Roll 10 x5 (254 x 1524) Mesh Roll 10 x25 (254 x 7620) ompound 1 Stick ompound 3 Sticks 35

36 Replacement s M SRWS Replacement Screw Minimum Number for Number Order , , , , , Series 9, , T-Slot Toe lamps TPR SRW (or I Xpansion lamp) Minimum Number (Metric) Screw or: Order (38001) Model # (38002) Model # (38010) Model # (38020) Model # (38032) Model # (38042) Model # (38052) Model #5, # (38072) Model #7, #8, #9, #10 2 MHINL UNIOR HNNL Minimum Number Model Order HX WSHRS (for ixture lamps) Replacement Washer Minimum Number for Number (Metric) Order , (50204) , (50206) , (50205) , 10205, (50208) (50207) , (50210) (50212) , (50216) 4 MHINL UNIOR LOKING PLT Minimum Number Model Order KNI G WSHRS Replacement Washer Minimum Number for Number (Metric) Order , (82584) , (82588) , (82592) 4 MHINING SRWS (for Machinable ixture lamps) Hold own Screw for Min. Number Number Order Hold own Screw for Min. Number Number Order UNIOR HNNL Minimum Number Model Order INH MTRI MHINL WSHRS - Steel (for Machinable ixture lamps) Replacement Washer Minimum Number for Number (Metric) Order , (50506) , (50510) , (50516) UNIOR WG (Slug) Minimum Number Model Order

37 Replacement s SQUR WSHRS Number (Metric) Use With am Screw: (Metric) T-NUT WITH ST SRW T-Slot Minimum Number Size Order SLOT WSHRS THR YLINRS (M-10M) (51016) (M-12M) (M-16M) Number Use with Mounting Screw: (Metric) /2-13 (M12 Screw) /8 (M16 Screw) Number Thread INH / / / / / /16 2 MTRI mm mm mm mm mm mm mm mm M M M M M M12 Notes 37

38 ustomer pplication Photos Pitbull lamps Machinable Pitbull lamps Pitbull lamps VersaGrip On a Lathe 38 Pitbull on 5th xis TalonGrip and Pitbull

39 ustomer pplication Photos Uniforce lamps I Xpansion lamp VacMagic VM300 with ustom Pallet Mitee-Grip VersaGrip in a Vise Images courtesy of Tombstone with Pitbull lamps VersaGrip and Machinable Pitbull 39

40 Helvetica old The cam action MIT-IT ixture lamp is made up of two simple components: a hardened steel socket cap screw with an offset head and a brass hexagonal washer. Low-profile makes computer programming easier am action provides fast, strong clamping Small size allows more parts per load Simple design keeps cost low * milled The Workholding Specialist istributed Worldwide Visit our website for a distributor in your country - Miteeite.com MIT-IT PROUTS LL 340 Route 16 P.O. ox 430 enter Ossipee, NH U.S.. Phone: (603) ax: (603) Toll ree: mail: miteebite@miteebite.com Mitee-ite Products LL is distributed by: Visit our website to view our latest product information: Miteeite.com 1 Mitee-ite Products LL 1011