ABSOLUTE Digimatic Indicator Page 250. Dial Indicator Page 262. Accessories for Indicator Page 280. Dial Test Indicator Page 289

Transcription

1 Indicators BSOUTE Digimatic Indicator Page 250 Dial Indicator Page 262 ccessories for Indicator Page 280 Dial Test Indicator Page 289 ccessories for Dial Test Indicators Page 297 Thickness Gauge, Depth Gauge, Caliper Gauge and Coating Thickness Gauge Page

2 BSOUTE Digimatic Solar Indicator ID-SS Series 543 This solar-powered, standard model is environmentally friendly and very easy to use. The BSOUTE Digimatic Solar Indicator ID-SS offers you the following benefits: The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle. There s no battery to change. The solar cell is operates from just 40 UX. Super-capacitor charge storage enables you to work in low-level lighting conditions of less than 40 UX. You can access all functions by using the large, user-friendly buttons on the front of the indicator. arge character height of 9 provides good readability. Functions Series 543 ORIGIN (BS-Zero) Digimatic data output Counting direction switchable ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Display Refer to the list of specifications (excluding quantizing error) Capacitance type, absolute linear encoder 8 Unlimited Carbide ball, thread M 2,5 x 0,45 Counting value composition error Solar cell usable from 40 UX illumination CD character height 9 Optional accessories Description 21EZ198 Spindle lifting lever (12,7 8,00 model) Spindle lifting cable 30 26,00 21EZ105 Spindle lifting knob (12,7 models) 26,00 Digimatic Signal Cables Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 02ZD790F Connecting cable U-Wave 85,00 06DV380F USB Input Tool Direct cable (2 m) 100,00 For USB Input Tool Direct cable: a footswitch (no T), a USB- footswitch adapter (no. 06DV384) and USB-ITPK Software (no. 06DV386) are required B B Description Standard contact point 11,00 Mass lug/plain Digital step ccuracy ug back plate [g] B ,7 0,001 0, / , B ,7 0,01 0,02 150/ ,00 with "B": Flat back plate ø ø59 ø ø ø M2.5x0.45 Sø

3 BSOUTE Digimatic Indicator ID-S Functions Series 543 ORIGIN (BS-Zero) Digimatic data output ON/OFF Counting direction switchable ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Battery life Display Optional accessories Refer to the list of specifications (excluding quantizing error) Capacitance type, BSOUTE linear encoder 8 Unlimited Carbide ball, thread M 2,5 x 0,45 ow voltage, counting value composition error 1 battery SR-44 approx hours (0,001 type) approx hours (0,01 type) CD, character height 9 Description 21EZ198 Spindle lifting lever (12,7 8,00 model) Spindle lifting cable 30 26,00 21EZ105 Spindle lifting knob (12,7 26,00 models) Silicon rubber boot 11,00 Digimatic Signal Cables Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 02ZD790F Connecting cable U-Wave 85,00 06DV380F USB Input Tool Direct cable (2 m) 100,00 For USB Input Tool Direct cable: a footswitch (no T), a USB- footswitch adapter (no. 06DV384) and USB-ITPK Software (no. 06DV386) are required only for B Description Standard contact point 11, Battery SR44 6,00 02C376 Rubber boot (NBR rubber) 02C376 only for B Series 543 This is a standard model of indicator that is reliable and easy to use. The BSOUTE Digimatic Indicator ID-S offers you the following benefits: The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle. You can access all functions by using the large, user-friendly buttons on the front of the indicator. arge character height of 9 provides good readability. Exceptional battery life B B ug back plate Digital step ccuracy Remarks Mass ug/flat [g] B B ,7 0,01 0,02 IP42 140/ , B ,7 0,001 0,003 IP42 140/ , B ,7 0,001 0,003 IP53 140/ ,00 with "B": Flat back plate ø EZ198 ø59 16 ø ø54 17 ø M2.5x Sø EZ

4 BSOUTE Digimatic Indicator ID-U Series 575 This is a slim type of digital indicator with a 25 range. The BSOUTE Digimatic Indicator ID-U offers you the following benefits: The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle. Its compact design makes it ideal for installing into measuring fixtures. Exceptional battery life ø4.8 M2.5X ø Functions Series 575 ORIGIN (BS-Zero) Digimatic data output ON/OFF Counting direction switchable ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Battery life Digital step Display Standard accessories Refer to the list of specifications (excluding quantizing error) Capacitance type, BSOUTE linear encoder 8 (ISO/JIS type) Unlimited Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) ow voltage, counting value composition error 1 battery SR-44 approx hours 0,01 CD, character height 8,5 Description Spindle lifting handle Optional accessories Description Spindle lifting cable 30 26,00 Digimatic Signal Cables Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 02ZD790F Connecting cable U-Wave 85,00 06DV380F USB Input Tool Direct cable (2 m) 100, :moving measuring range max. 12 For USB Input Tool Direct cable: a footswitch (no T), a USB- footswitch adapter (no. 06DV384) and USB-ITPK Software (no. 06DV386) are required. Description Battery SR44 6, Standard contact point 11,00 Mass ccuracy [g] ,4 0, ,00 252

5 BSOUTE Digimatic Indicator ID-C Calculation : f(x) = x Mounting the ID-C on a measuring fixture and setting the multiplying factor "" (between 0,0001 and 99,9999) allows direct measurement without using a conversion table and improves measurement efficiency Series 543 This is a multifunction indicator that is reliable and easy to use. The BSOUTE Digimatic Indicator ID-C offers you the following benefits: The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle. GO/±NG judgement is performed by setting the upper and lower tolerances. You can make simple calculations by a user-definable factor using the formula x ( x is spindle displacement). arge character height of 11 provides good readability. Display 330 rotatable. function lock protects the display against unauthorised use. 330 rotary display The display can be rotated 330, allowing use at a position where you can easily read the measurement value 12,7 range model 25,4 range model Function locking Ensures reliability of measurement by locking the settings to prevent preset function settings from being changed by mistake 50,8 range model ø ø ø arge CD The large CD incorporates 11 characters making measurement values much easier to read ø ø59 M2.5X ,7 range models ø6.5 ø ø ø59 M2.5X0.45 ø ø ø59 Tolerance function 2 kinds of tolerance visualisation 25,4 range models M2.5X0.45 ø4.8 50,8 range models 253

6 BSOUTE Digimatic Indicator ID-C Series 543 Mass Digital step ccuracy Remarks ug back plate [g] B ,7 0,001/0,01 0, , B ,7 0,001/0,01 0,003 ow force , B ,7 0,01 0, , B ,7 0,01 0,02 ow force , B 25,4 0,001/0,01 0, , B 25,4 0,01 0, , B 50,8 0,001/0,01 0, , B 50,8 0,01 0, ,00 with "B": Flat back plate Specification low measuring force models : see below Spindle lifting handle Spindle lift knop Spindle lifting lever Spindle lifting cable 500 Setting measuring force on low measuring force models /404B Spindle orientation Spring Weight (approximately 0.1N) Pointing vertically downward Yes Yes 0.5N Yes No 0.4N No Yes 0.3N No No 0.2N Horizontal Yes No 0.2N /394B Spindle orientation Spring Weight (approximately 0.1N) Pointing vertically downward Horizontal Yes Yes 0.7N Yes No 0.6N No Yes 0.4N Spindle lifting lever Spindle lifting cable 300 Maximum measuring force Maximum measuring force No No Not defined Not defined Functions Series 543 ZERO/BS GO/±NG judgement Digimatic data output ON/OFF DT/HOD ock function PRESET Counting direction switchable Calculation function Selectable resolution* ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Battery life Display Optional accessories Refer to the list of specifications (excluding quantizing error) Capacitance type, BSOUTE linear encoder 8 (ISO/JIS type) Unlimited Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) ow voltage, counting value composition error, overflow error, tolerance limit setting error 1 battery SR-44 approx hours CD character height 11 Rotatable 330 Description Spindle lifting cable 30 26, Spindle lifting cable ,00 21EZ198 Spindle lifting lever (12,7 8,00 model) 21EZ105 Spindle lifting knob (12,7 26,00 models) 21EZ197 Spindle lifting knob (25,4 57,00 models) 21EZ200 Spindle lifting knob (50 69,00 models) Spindle lifting handle 2,00 02C571 uxiliary spindle spring 10,00 (25,4 models) 02C773 uxiliary spindle spring (50 models) 10,00 Digimatic Signal Cables Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 02ZD790F Connecting cable U-Wave 85,00 06DV380F USB Input Tool Direct cable (2 m) 100,00 02C571/02C773 : required when orienting the indicator upside down 21EZ105 : not available for low measuring force models : moving measuring range max. 28 Description Battery SR44 6, Standard contact point 11,00 *0,001 type 254

7 BSOUTE Digimatic Indicator Calculator ID-C Functions Series 543 ZERO/BS GO/±NG judgement Digimatic data output ON/OFF DT/HOD Max/Min value reading ock function PRESET Calculation function Selectable resolution Series 543 This Digimatic indicator calculator allows you to calculate the calculation function x + B + Cx-1. It offers you the following benefits: Multi-functional indicator with integrated calculation formula is useful in a variety of applications. Coefficients, B and C are freely definable. X = displacement of plunger. The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle Ø 10.9 ccuracy Scale Max/Min function Stem Ø Max. response speed Contact point larm Power supply Battery life Display Optional accessories Refer to the list of specifications (excluding quantizing error) Capacitance type, BSOUTE linear encoder t a speed of 10 µm/sec, the peak value may not always be correctly displayed 8 (ISO/JIS type) Unlimited Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) ow voltage, counting value composition error, overflow error, tolerance limit setting error 1 battery SR-44 approx. 12 months (8h/day) CD, character height 8,5 Rotatable 330 Description Spindle lifting cable 30 26, Spindle lifting lever 6,00 Digimatic Signal Cables Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 02ZD790F Connecting cable U-Wave 85,00 06DV380F USB Input Tool Direct cable (2 m) 100, B The resolution can be selected from 12 classes: Class Class Class 1 0, , ,1 2 0, , ,2 3 0, , ,5 4 0, , M Ø Ø4.8 Ø Ø Description Battery SR44 6, Standard contact point 11,00 Measuring force Mass ccuracy [N] [g] B 12,7 0,003 1, , B 25,4 0,003 1, , B 50,8 0,006 2, ,00 21FJ Measuring bridges R 21FJ , , ,00 21FJ395 outside : / inside : ,00 The accuracy of a radial measurement using the measuring bridges depends on the size of the radius to be measured and the form error of the workpiece FJ

8 BSOUTE Digimatic Indicator Signal ID-C Series 543 This indicator signal has signal input no voltage input (remote control) and signal output NPN open collector. It offers you the following benefits: With the MX/MIN value holding function, this indicator can output the signal of the GO/±NG judgement result against the peak value set. You can output the judgement signal to an external device, such as a sequencer, through the NPN open-collector connection. External power of DC 12-24V It comes with a 4m cable B ø54 5 ø Mass Digital step ccuracy ug back plate [g] B ,7 0,001 0, , Wire colour Signal name I/O Description Black - V (GND) - Connect to the minus (-) terminal Red + V (plus power voltage) I ø Supply a power voltage between 12 VDC and 24 VDC Orange - NG O Tolerance judgement result output terminals (NPN open-collector Green OK O output) : Only the terminal to a judgement result is set to the low Brown + NG O level. (See the output circuit diagram) Yellow Blue PRESET_REC/ZERO HOD_RESET I I External input terminals (no-voltage input) : If the relevant terminal is set to the low level, its signal becomes true. (See the input circuit diagram) Shield FG (Grame Ground) - Connect to the ground. I/O ø10.9 ø m Functions Series 543 Signal output: NPN open-collector, (+NG, OK, -NG) Signal input: No-voltage input, (PRESET_REC/ZERO, HOD_RESET) ZERO/BS GO/±NG judgement ON/OFF Max/Min/Runout value Tolerance assessment via ED PRESET Counting direction switchable Tolerance display ccuracy Measuring force Scale Max/Min function Max. response speed Stem Ø Contact point larm Power supply Display Delivered Optional accessories Refer to the list of specifications (excluding quantizing error) 2 N Capacitance type, BSOUTE linear encoder t a speed of 50 µm/sec, the peak value may not always be correctly displayed Unlimited 8 (ISO/JIS type) Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) or Counting value composition error, overflow error, tolerance limit setting error DC 12-24V±10% CD, character height 8,5 With signal cable 4 m. One end is fixed to the main unit. no connector is supplied for the other end. Description Spindle lifting cable 30 26, Spindle lifting lever 6, Silicon rubber boot 11,00 Description 02C376 Rubber boot (NBR rubber) Standard contact point 11,00 Wire -NG OK +NG Composition error Orange (-NG) ow High High High Green (OK) High ow High High Brown (+NG) High High ow High ED Red Green Red Red (blinking) CD < O > "x.xxe" indication Output pattern 256

9 BSOUTE Digimatic Indicator Max/Min/RNGE ID-C Functions Series 543 ZERO/BS GO/±NG judgement Digimatic data output ON/OFF Max/Min/Runout value PRESET Counting direction switchable ccuracy Measuring force Scale Max/Min function Stem Ø Max. response speed Contact point larm Power supply Battery life Display Refer to the list of specifications (excluding quantizing error) 1,5 N Capacitance BSOUTE linear encoder t a speed of 50 µm/sec, the peak value may not always be correctly displayed 8 (ISO/JIS type) Unlimited Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) or ow voltage, counting value composition error, overflow error, tolerance limit setting error 2 batteries SR-44 approx hours CD, character height: 8,5 Rotatable 330 Series 543 This indicator is the max/min value holding function model, and offers you the following benefits: The maximum, minimum or range (runout value) can be displayed during measurement. High sampling rate of 50 times/s. The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle. ø54 5 ø M ø ø10.5 ø Optional accessories Description Spindle lifting lever 6, Spindle lifting cable 30 26,00 Digimatic Signal Cables Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 02ZD790F Connecting cable U-Wave 85,00 06DV380F USB Input Tool Direct cable (2 m) 100, B Mass Digital step ccuracy ug back plate [g] B ,7 0,001 0, ,00 Description Battery SR44 6, Standard contact point 11,00 Point B Point Point D B C Point C Difference/Runout measurement Example : Indicator travel from points to D : Difference (or Total Runout) is displayed as. Dimensions B (maximum value) and C (minimum value) can be measured with a simple key sequence. 257

10 BSOUTE Digimatic Indicator ID-N Series 543 This is a slim back-plunger model that is highly resilient and robust. The BSOUTE Digimatic Indicator ID-N offers you the following benefits: It slim body design is ideal for multi-point measurements. The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle. It has excellent resistance against water and dust (IP66 protection level) allowing you to use it in machining situations that include splashing coolant fluid. Switchable display orientation gives you more mounting options. You can perform GO/±NG judgement by setting the upper and lower tolerances Flexible installation options switchable display orientation (overhead use) Width of 35 instead of 60 as standard Digimatic indicators Measuring force Mass Digital step ccuracy [N] [g] ,7 0,01 0,02 2, , ,7 0,01 /0,001 0,003/0,01 2, ,00 Functions Series 543 GO/±NG judgement Digimatic data output ON/OFF DT/HOD Signal input PRESET or external ZERO PRESET Counting direction switchable Selectable resolution* ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Battery life Display Optional accessories Refer to the list of specifications (excluding quantizing error) Capacitance type, BSOUTE linear encoder 8 (ISO/JIS type) Unlimited Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) or ow voltage, counting value composition error, overflow error, tolerance limit setting error 1 battery SR-44 approx hours CD, character hight: 6,2 Description Silicon rubber boot 11,00 21EZ145 Back plate with centre lug 16,00 21EZ105 Spindle lifting knob (12,7 models) 26,00 Digimatic Signal Cables 21E194 Digimatic cable 1 m 52,00 21E190 Digimatic cable 2 m 62,00 02ZD790G Connecting cable U-Wave 90,00 06DV380G USB Input tool Direct cable 100,00 (2 m) 21E210 Digimatic cable for external 149,00 preset/zero (1 m) 21E211 Digimatic cable for external preset/zero (2 m) 170,00 Description Standard contact point 11, Battery SR44 6,00 02C376 Rubber boot (NBR rubber) R E ø E M2.5x0.45 * 0,001 type 258

11 BSOUTE Digimatic Indicator ID-B Functions Series 543 GO/±NG judgement Digimatic data output ON/OFF DT/HOD Signal input PRESET or external ZERO PRESET Counting direction switchable Selectable resolution* ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Battery life Display Optional accessories Refer to the list of specifications (excluding quantizing error) Capacitance type, BSOUTE linear encoder 8 (ISO/JIS type) Unlimited Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) ow voltage, counting value composition error, overflow error, tolerance limit setting error 1 battery SR-44 approx hours CD, character hight: 6,2 Description 21E212 Silicon rubber boot 10,00 21EZ145 Back plate with centre lug 16,00 Digimatic Signal Cables 21E194 Digimatic cable 1 m 52,00 21E190 Digimatic cable 2 m 62,00 02ZD790G Connecting cable U-Wave 90,00 06DV380G USB Input tool Direct cable 100,00 (2 m) 21E210 Digimatic cable for external 149,00 preset/zero (1 m) 21E211 Digimatic cable for external preset/zero (2 m) 170,00 Series 543 This is a slim back-plunger model that is highly resilient and robust. The BSOUTE Digimatic Indicator ID-B offers you the following features: It is a back plunger type, with the display viewed from above. Its slim body design is ideal for multi-point measurements. The BSOUTE sensor means you don t have to carry out origin setting every time you power it on, saving you time and hassle. It has excellent resistance against water and dust (IP66 protection level) allowing you to use it in machining situations that include splashing coolant fluid. Switchable display orientation gives you more mounting options. You can perform GO/±NG judgement by setting the upper and lower tolerances Flexible installation options with switchable display orientation (overhead use) Measuring force Mass Digital step ccuracy [N] [g] ,01 0, , ,001 /0,01 0,01/0, ,00 IP66 Description Battery SR44 6, Standard contact point 11, Rubber boot (NBR Rubber) 6, E R ø E *0,001 type 5.6 M2.5x

12 Digimatic Indicator ID-H Series 543 This is a superior multi-function indicator that gives you high accuracy and high resolution of 0,0005. The Digimatic Indicator ID-H offers you the following benefits: 2-colour CD backlight (green and red) provides you with visual GO/±NG tolerance judgement and analogue bar-graph display. You can display the maximum, minimum or range (runout value) during measurement. ifting mechanism over 30 with cable release (optional). You can carry out zero-setting and presetting with the optional remote controller, without having to touch the indicator. The remote control system can be implemented in advance with the built-in RS-232 interface and a PC. External power supply via C-dapter D 21EZ099 Remote Control: Data export Reset Max/Min/TIR Max/Min/TIR switchover Call PRESET value Measuring force Mass ccuracy [N] [g] D 30,4 0, , D 60,9 0,0025 2, ,00 Point B (251.3) 90 (60) (47.3) 61.5 (31) ø12 ø M2.5x Functions Series 543 ZERO GO/±NG judgement Digimatic data output Digimatic data input ON/OFF DT/HOD RS-232C data output* nalogue measuring range switchable Max/Min/Runout value RS-232C data input* ock function PRESET Counting direction switchable Selectable resolution ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Digital step Display Standard accessories Refer to the list of specifications (excluding quantizing error) Photoelectric linear encoder 8 (ISO/JIS type) 1000 /s Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) Counting value composition error, overflow error, tolerance setting error C adapter 6 V DC, 2 0,001 /0,0005 CD, character height: 9,5 Description 06EG180D C dapter 6V DC, Spindle lifting handle Optional accessories Description 21EZ099 Remote control 75, Spindle lifting cable 30 26,00 21EZ101 Spindle lifting knob 26, D Digimatic Presetter Digimatic Signal Cables Digimatic cable (1 m) 44, Digimatic cable (2 m) 58,00 02ZD790D Connecting cable U-Wave 85,00 06DV380D USB Input Tool Direct cable 100,00 (2 m) 21E130 RS-232C cable (1 m) 170,00 21E131 RS-232C cable (2 m) 191, : moving measuring range max. 30 Point Point C Point D Difference/Runout measurement Example : indicator travel from points to D. Difference (or Total Runout) is displayed as. Dimensions B (maximum value) and C (minimum value) can be recalled from memory with a simple key sequence. B C Digimatic presetter (optional) : External keyboard for entering tolerance data or preselecting values Description Battery for remote control 10,00 (4 x R03 / ) Standard contact point 11,00 * RS-232 Input/Output Connect this instrument with an external device such as a PC using the RS-232 dedicated cable (optional accessory). With this connection it is possible to perform initial setup of the instrument, control of switching a measurement mode, etc., and processing such as measurement data transfer. The display switches from green to red backlight if the upper or lower tolerance limit is exceeded Max/Min/TIR value measurement 260

13 Functions ZERO/BS GO/±NG judgement Digimatic data output Digimatic data input ON/OFF nalogue measuring range switchable Max/Min/Runout value ock function PRESET Counting direction switchable Selectable resolution Series Superior multifunction indicator BSOUTE Digimatic Indicator ID-F Series Superior multifunction indicator This is a superior multifunction indicator. The BSOUTE Digimatic Indicator ID-F offers you the following benefits: 2-colour CD backlight (green and red) provides you with visual GO/±NG tolerance judgement and analogue bar-graph display. You can display the maximum, minimum or range (runout value) during measurement. External power supply via C-dapter. ccuracy Scale Stem Ø Max. response speed Contact point larm Power supply Digital step Display Refer to the list of specifications (excluding quantizing error) Capacitance type, BSOUTE linear encoder 8 (ISO/JIS type) Unlimited Carbide ball, thread M 2,5 x 0,45 (ISO/JIS type) Counting value composition error, overflow error, tolerance limit setting error C adapter 9V DC, 500m 0,001 /0,01 CD character height 8, D D Visual tolerance-monitoring Standard accessories Description 06EG302D C dapter 9V, 500m Spindle lifting handle Optional accessories Description Spindle lifting cable 30 26,00 02C571 uxiliary spindle spring 10,00 (25,4 models) 02C773 uxiliary spindle spring (50 10,00 models) Digimatic Presetter Digimatic Signal Cables Digimatic cable (1 m) 44, Digimatic cable (2 m) 58,00 02ZD790D Connecting cable U-Wave 85,00 06DV380D USB Input Tool Direct cable (2 m) 100, : moving measuring range max.12 02C571/02C773 : required when orienting the indicator upside down Description Standard contact point 11,00 Measuring force Mass ccuracy [N] [g] D 25 0,003 1, , D 50 0,003 2, , D 50 0,006 2, , ø4.8 M ø ø ø4.8 M C B Digimatic presetter (optional) : External keyboard for entering tolerance data or preselecting values Point B Point Point D Point C Difference/Runout measurement Example : indicator travel from points to D. Difference (or Total Runout) is displayed as. Dimensions B (maximum value) and C (minimum value) can be measured with a simple key sequence. 261

14 Dial Indicator Series 1 Series 1 Series 1 This is a compact, small diameter metric indicator that offers you the following benefits: It is ideal for use in applications where space is limited. Bezel ø 31, ø 36, ø 40 Functions Balanced dial Continuous dial Shockproof Jeweled bearing 1003TB 1911TB TB SB SB SB Description 21Z319 Standard contact point 3, Standard contact point 11, : for 1109S-10 / 1013S-10 / 1124S 21Z319 : for 1913T-10 / 1911T-10 / 1003T-10 For accessories and contact points, see end of dial indicators section D E 1913T TB I ø S-10 øc 16(13) øh ug Mass lug/plain Graduation Scale back plate per rev. [g] 1913TB T-10 0,5 0,2 0, /46 143, SB S ,2 0, /75 139, SB S ,2 0, /75 141, TB T-10 2,5 1 0, /46 136, SB 1124S 3,5 0,5 0, (50-0) 90/70 93, TB 1003T , /48 98,00 ø8 B G F ø4 B C D E F G H I Measuring force [N] 1913TB-10 15,5 39, ,5 19,4 15,2 8, ,3-1,8 1109SB-10 32, , ,8 15,2 38 6,6 0,4-1,5 1013SB-10 32, , ,8 15,2 38 6,6 0,4-1,5 1911TB-10 15, ,5 19,4 15,1 11, ,3-1,8 1124SB 32, , ,8 12,2 38 6,6 0,4-1,4 1003TB 18 40, ,5 12, ,3-1,4 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 1913TB , ,5 1109SB ,5 4 4,5 5, SB ,5 4 4,5 5, TB SB TB Repeatability Hysteresis error 1911T S S 262

15 Dial Indicator Series 1 Series 1 Series 1 Functions Balanced dial Continuous dial Jeweled bearing IP63 Double scale spacing 1040SB 1044SB 1044SB SB SB 1045SB This is a compact, small diameter metric indicator that offers you the following benefits: It is ideal for use in applications where space is limited. Bezel ø S(B)-60 Description Standard contact point 11, Rubber boot (NBR rubber) 7, Standard contact point for waterproof type 16, and : for 1044S-60 (IP model) For accessories and contact points, see end of dial indicators section 1044S 1045S 1040S 1044S-60 IP63 ug Mass lug/plain Graduation Scale back plate per rev. [g] 1040SB 1040S 3,5 0,5 0, (50-0) 90/70 80, SB 1041S 3,5 0,5 0, /70 83, SB 1044S 5 1 0, (100-0) 90/70 50, SB S , (100-0) 90/70 78, SB S , (100-0) 90/70 97, SB 1045S 5 1 0, /70 65, SB-15: ow measuring force model. Use in vertical position only (contact point downward) B C D E F G H I Measuring force [N] 1040SB 32, , ,8 12,2 38 6,6 0,4-1,4 1041SB 32, , ,8 12,2 38 6,6 0,4-1,4 1044SB 32,5 47, , ,8 13,7 38 6,6 0,4-1,4 1044SB-15 32,5 47, , ,8 13,7 38 6,6 0,1-0,4 1044SB-60 32, , ,2 24,8 38 6,6 0, SB 32,5 47, , ,8 13,7 38 6,6 0,4-1,4 B G F øc D E ø ø4 ø øh 1044S-15 5 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 1040SB SB SB SB SB SB Repeatability Hysteresis error I M

16 One Revolution Dial Indicator Series 1 Series 1 Series 1 This is a compact model of indicator that offers you the following benefits: By limiting the pointer rotation to one, reading errors that can occur with other dial indicators are eliminated. Bezel ø 40. Functions Balanced dial One Shockproof Jeweled bearing Dustproof IP SB SB 1929SB-62 Description Standard contact point 11,00 For accessories and contact points, see end of dial indicators section. 1929S-62 D E ø SB 1929S ug back plate 1929S 1929SB S SB S-72 1 (plunger stroke:3,5) 1 (plunger stroke: 3,5) 0,1 (plunger stroke: 2) per rev. Graduation Scale 1900S-72 Mass lug/plain [g] 1,4 0, /70 88,00 1,4 0, /70 112,00 0,14 0, /75 157,00 B G F øc I ø ø4 M øh B C D F E H G I Measuring force [N] 1929SB 32,5 47, ,5 13, ,7 6,6 0,4-1,4 1929SB-62 32,5 47, ,5 13, ,7 6,6 0,4-1,4 1900SB-72 32,5 53, ,5 16, ,7 6,6 0,4-1,4 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 1929SB SB SB Repeatability Hysteresis error 264

17 F Dial Indicator Series 2 Series 2 Series 2 Functions Balanced dial Continuous dial Shockproof IP SB 2044SB SB SB This is a standard type metric dial indicator with 0,01 scale graduation, with bezel Ø 57, 5/10 range 2044S(B)-60 Description Standard contact point 11, Rubber boot (NBR Rubber) 6, Standard contact point for waterproof type 16, and : for 2044S-60 (IP model) For accessories and contact points, see end of dial indicators section D E S 2044S S ø6.5 5 øc 16 øh B G ø ø4.8 I M ug Mass lug/plain Graduation Scale back plate per rev. [g] 2044SB 2044S 5 1 0, (100-0) 145/136 58, SB S , (100-0) 147/138 61, SB S , (100-0) 147/ , SB 2045S 5 1 0, /136 63,00 B C D F E H G I Measuring force [N] 2044SB 48,8 65, ,7 16, ,8 7,6 0,4-1,4 2044SB-09 48,8 65, ,7 16, ,8 7,6 0,4-1,4 2044SB-60 48, ,7 12, ,2 7,6 0,4-2,5 2045SB 48,8 65, ,7 16, ,8 7,6 0,4-1,4 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2044SB SB SB SB Repeatability Hysteresis error 265

18 F B Dial Indicator Series 2 Series 2 Series 2 This is a standard type metric dial indicator with 0,01 scale graduation, with bezel Ø 57, 10 range 2046S(B)-60 Functions Balanced dial Continuous dial Reverse reading Shockproof Jeweled bearing IP64 Coaxial counter 2046SB 2046SB SB SB SB 2047SB Description Standard contact point 11, Standard contact point for 16,00 waterproof type Rubber boot (NBR Rubber) 6, and : for 2046S-60 (IP model) 2046S 2902S 2047S For accessories and contact points, see end of dial indicators section ug Mass lug/plain Graduation Scale back plate per rev. [g] 2046SB 2046S , (100-0) 144/135 32, SB S , (100-0) 146/137 56, SB S , (100-0) 146/ , SB S , (100-0) 146/137 62, SB 2902S , /135 68, SB 2047S , /135 61,00 B C D F E H G I Measuring force [N] 2046SB 48,8 65, ,7 16, ,8 7,6 0,4-1,4 2046SB-09 48,8 65, ,7 16, ,8 7,6 0,4-1,4 2046SB-60 48, ,7 12, ,2 7,6 0,4-2,5 2310SB-10 48,8 65, ,7 16, ,8 7,6 0,4-1,4 2902SB 48,8 65, ,7 16, ,8 7,6 0,4-1,4 2047SB 48,8 65, ,7 16, ,5 7,6 0,4-1,4 2046S-60 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2046SB SB SB SB SB SB Repeatability Hysteresis error 2310S-10 øc D E ø øh ø ø4.8 G M I 266

19 F Dial Indicator Series 2 Series 2 Series 2 Functions Balanced dial Continuous dial Shockproof Jeweled bearing IP64 Double scale spacing 2109SB SB SB SB-70 This is a standard type metric dial indicator with 0,001 scale graduation, with bezel Ø 57, 1 range 2109S S-70 Description Standard contact point 11,00 21Z320 Standard contact point 8, Standard contact point for 16,00 waterproof type Rubber boot (NBR rubber) 7, : for 2110S-70 21Z320 and : for 2109S-70 For accessories and contact points, see end of dial indicators section. D E 2110S S SB-70 B øc G ø ø4.8 ø øh ug Mass lug/plain Graduation Scale back plate per rev. [g] 2110SB S ,1 0, (100-0) 149/ , SB S ,1 0, (100-0) 150/ , SB S ,2 0, /139 85, SB S ,2 0, / ,00 M I B C D F E H G I Measuring force [N] 2110SB-10 48,8 66, ,7 16, ,2 7,6 0,9-1,5 2110SB-70 48,8 67, ,7 12, ,7 7,6 0, SB-10 48,8 60, ,7 16, ,1 7,6 0,9-1,5 2109SB-70 48,8 65, ,7 12, ,5 7,6 0,9-2 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2110SB ,5 4 4, SB ,5 4 4, SB ,5 4 4, SB ,5 4 4, Repeatability Hysteresis error 267

20 Dial Indicator Series 2 Series 2 Series 2 This is a standard type with 0,001/0,005 scale graduation, with bezel Ø 57, 2/5 range Functions Balanced dial Continuous dial Shockproof Jeweled bearing 2113SB SB-10 F 2118SB SB-10 Description Standard contact point 11,00 For accessories and contact points, see end of dial indicators section. 2113S S S S D E ug Mass lug/plain Graduation Scale back plate per rev. [g] 2113SB S ,2 0, / , SB S ,2 0, / , SB S ,2 0, / , SB S ,5 0, (50-0) 146/137 83,00 B øc ø ø øh ø4.8 B C D F E H G I Measuring force [N] 2113SB-10 48, ,7 16, ,6 7,6 0,4-1,5 2118SB-10 48,8 60, ,7 16, ,9 7,6 0,4-1,5 2119SB-10 48,8 60, ,7 16, ,9 7,6 0,4-1,5 2124SB-10 48,8 60, ,7 16, ,9 7,6 0,4-1,5 G I M DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2113SB ,5 4 4, SB ,5 9,5 1,5 2,5 2119SB ,5 9,5 1,5 2,5 2124SB Repeatability Hysteresis error 268

21 Dial Indicator with 20 Stroke Series 2 Series 2 Series 2 Functions Continuous dial Shockproof Jeweled bearing IP64 Cushioned end point Coaxial counter 2050SB 2320SB SB SB-19 This is a standard metric dial indicator that offers you the following benefits: 20 stroke. Bezel ø 57, graduation 0, S(B)-60 Description Standard contact point 11,00 21Z321 Standard contact point 13,00 21Z321 : for 2050S-60 (IP model) For accessories and contact points, see end of dial indicators section. 2320S-10 D E ø6.5 5 øc 16 øh 2050S 2050S S-60 B G F ø I M ug Mass lug/plain Graduation Scale back plate per rev. [g] 2050SB 2050S , (100-0) 149/140 83, SB S , (100-0) 155/ , SB S , (100-0) 149/140 83, SB S , (100-0) 150/141 83,00 B C D F E H G I Measuring force [N] 2050SB 38,8 75, ,7 16, ,8 7,6 0, SB-60 38,8 75, ,7 12, ,8 7,6 0,4-2,5 2050SB-19 38,8 75, ,7 16, ,8 7,6 0, SB-10 38,8 75, ,7 16, ,8 7,6 0,4-2 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2050SB SB SB SB Repeatability Hysteresis error 269

22 Dial Indicator with 30 Stroke Series 2 Series 2 Series 2 This is a standard metric dial indicator that offers you the following benefits: 30 stroke. Bezel ø 57, graduation 0,01 Functions Continuous dial Reverse reading Shockproof Jeweled bearing Cushioned end point Coaxial counter 2052SB 2330SB SB SB 2952S 2330S-10 Description Standard contact point 11,00 For accessories and contact points, see end of dial indicators section. D E ø6.5 5 øc 16 øh 2052S 2052S-19 ug Mass lug/plain Graduation Scale back plate per rev. [g] 2052SB 2052S , (100-0) 152/143 91, SB S , (100-0) 152/ , SB S , (100-0) 150/ , SB 2952S , / ,00 B G F ø I M B C D F E H G I Measuring force [N] 2052SB 38,8 75, ,7 16, ,8 7,6 0,4-2,5 2052SB-19 38,8 75, ,7 16, ,8 7,6 0,4-2,5 2330SB-10 38,8 75, ,7 16, ,8 7,6 0,4-2,5 2952SB 38,8 75, ,7 16, ,8 7,6 0,4-2,5 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2052SB SB SB SB Repeatability Hysteresis error 270

23 Functions Balanced dial Continuous dial Jeweled bearing Peak retaining Coaxial counter djustable pointer 2046SB-80 Series SB-10 Special Dial Indicator Series 2 Series 2 This is a dial indicator with a special design that offers you the following benefits: Standard size Bezel Ø 57, Graduation 0,01 Description 21Z319 Standard contact point 3, Standard contact point 11, : for 2046S-80 21Z319 : for 2048S-10 For accessories and contact points, see end of dial indicators section ø ø ø M ø S S S-80 ug Mass lug/plain Measuring force Graduation Scale back plate per rev. [g] [N] 2048SB S , (100-0) 144/135 0,4-1,4 76, SB S , (100-0) 158/149 0, ,00 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2048SB SB ø6.5 ø57 16 ø Repeatability Hysteresis error ø M S

24 One Revolution Dial Indicator Series 2 Series 2 This is a lightweight one dial indicator that gives you error-free reading. The One Revolution Dial Indicator offers you the following benefits: imiting the pointer rotation to one eliminates the reading errors that can occur with other dial indicators that use multiple pointer s for a full stroke. Graduation 0,01/ 0,02 Functions One Cushioned end point Dustproof IP52 Series TB up to 2973TB Description Standard contact point 11,00 For accessories and contact points, see end of dial indicators section. 2971TB 2972TB 2973TB 2971TB 2972TB 2973TB Mass lug/plain Graduation Scale per rev. [g] 0,5 (plunger stroke: 3,5) 0,7 0, ,00 1 (plunger stroke: 3,5) 1,4 0, ,00 1,6 (plunger stroke: 3,5) 2 0, ,00 B C D F G H I Measuring force [N] 2971TB 43,2 65, ,5 20,3 16,8 55 7,6 0,4-1,4 2972TB 43, ,5 20,3 17,2 55 7,6 0,4-1,4 2973TB 43,2 66, ,5 20,3 17,5 55 7,6 0,4-1,4 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2971TB TB TB Repeatability Hysteresis error Should the workpiece be approx. 1 larger than the nominal dimension, the part is assessed as good if the smaller pointer is ignored. Fault-free identification of rejects. 272

25 Functions One Shockproof IP64 Dustproof IP SB up to 2959SB Series SB SB-60 Description Rubber boot (NBR Rubber) 6, Standard contact point for 16,00 waterproof type Standard contact point 11, and : for 2929S-60 (IP model) For accessories and contact points, see end of dial indicators section. One Revolution Dial Indicator Series 2 Series 2 This is a lightweight one dial indicator that gives you error-free reading. The One Revolution Type Dial Indicator offers you the following benefits: imiting the pointer rotation to one eliminates the reading errors that can occur with other dial indicators that use multiple pointer s for a full stroke. Graduation 0,01/ 0,1 2929S(B) S 2929S 2929S SB-60 D E 2928S 2929SB ug back plate 2929S 2929SB S SB S SB 2928SB 2959S 2928S 0,8 (plunger stroke: 5) 0,8 (plunger stroke: 5) 0,8 (plunger stroke: 5) 1,6 (plunger stroke: 5) 4 (plunger stroke: 10) per rev. Graduation Scale Mass lug/plain [g] 1 0, /136 84,00 1 0, / ,00 1 0, / ,00 2 0, / ,00 5 0, / ,00 øc ø øh 5 B C D F E G H I Measuring force [N] 2929SB 48,8 65, ,7 16, ,8 52 7,6 0,4-1,4 2929SB-60 48, ,7 12, ,2 52 7,6 0, SB-62 48,8 65, ,7 16, ,8 52 7,6 0, SB 48,8 65, ,7 16, ,8 52 7,6 0,4-1,4 2928SB 48,8 65, ,7 16, ,8 52 7,6 0,4-1,4 B G F ø I M DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2929SB SB SB SB SB Repeatability Hysteresis error 273

26 One Revolution Dial Indicator Series 2 Series 2 Series 2 This is a lightweight one dial indicator that gives you error-free reading. The One Revolution Type Dial Indicator offers you the following benefits: imiting the pointer rotation to one eliminates the reading errors that can occur with other dial indicators that use multiple pointer s for a full stroke. Graduation 0, S(B)-70 Functions One Shockproof Jeweled bearing IP64 Dustproof IP SB SB SB SB-70 Description Standard contact point 11, Standard contact point for 16,00 waterproof type Rubber boot (NBR Rubber) 6, and : for 2900S-70 (IP model) For accessories and contact points, see end of dial indicators section. 2901S-10 D E ø S-70 øc 16 øh 2900S S-72 ug Mass lug/plain Graduation Scale back plate per rev. [g] 2900SB S-10 0,08 (plunger stroke: 4,5) 0,1 0, / , SB S-70 0,08 (plunger stroke: 4,5) 0,1 0, / , SB S-72 0,08 (plunger stroke: 4,5) 0,1 0, / , SB S-10 0,16 (plunger stroke: 4,5) 0,2 0, / ,00 B G F ø I M B C D F E G H I Measuring force [N] 2900SB-10 48, ,7 16, ,6 52 7,6 0,4-1,4 2900SB-70 48, ,7 12, ,2 52 7,6 0, SB-72 48, ,7 16, ,6 52 7,6 0, SB-10 48,8 66, ,7 16, ,7 52 7,6 0,4-1,4 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2900SB , SB , SB , SB ,5 1, Repeatability Hysteresis error 274

27 Dial Indicator Series 3 Series 3 Series 3 Functions Balanced dial Continuous dial Shockproof Jeweled bearing 3046SB 3047SB 3109SB-10 This is a metric dial indicator that offers you the following benefits: Bezel ø range with graduation 0,01 and 1 range with graduation 0,001. Description Standard contact point 11,00 For accessories and contact points, see end of dial indicators section ø78 16 ø S S-10 ø6.5±0.1 5 B C D ø M ug Mass lug/plain Graduation Scale back plate per rev. [g] 3046SB 3046S , (100-0) 252/ , SB 3047S , / , SB S ,2 0, / ,00 B C D Measuring force [N] 3046SB 61,2 75,5 15,9 20,6 0,4-1,4 3047SB 61,2 75,5 15,9 20,6 0,4-1,4 3109SB-10 61,2 75,5 25,9 14,1 0,4-1,5 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 3046SB SB SB ,5 4 4, Repeatability Hysteresis error 275

28 Dial Indicator with arge Diameter Scale Series 3 Series 3 Series 3 This is a metric dial indicator that offers you the following benefits: Bezel ø /30/50/80/100 range with graduation 0, Functions Continuous dial Shockproof Jeweled bearing Cushioned end point Coaxial counter 3050SB 3052SB-19 up to 3062SB-19 Description 21Z319 Standard contact point 3, Standard contact point 11,00 ø78 16 ø : for 3050S 21Z319 : for 3052S-19 / 3058S-19 / 3060S-19 / 3062S-19 ø6.5±0.1 5 For accessories and contact points, end of dial indicators section. D B C ø S M ug Mass lug/plain Graduation Scale back plate per rev. [g] 3050SB 3050S , (100-0) 272/ , SB S , (0-100) 285/ , SB S , (100-0) 298/ , SB S * 0, (0-100) 314/ , SB S * 0, (100-0) 332/ ,00 *3060S-19 and 3062S-19 : use in a vertical position only. B C D Measuring force [N] 3050SB 52, ,9 29,1 0, SB-19 72,9 104,3 25,9 39,4 0,4-2,5 3058SB-19 81,9 142,3 43,9 59,4 0, SB ,9 202,3 73,9 89,4 0, SB ,9 243,3 94,9 109,4 0,4-3,2 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 3050SB SB SB SB SB Repeatability Hysteresis error 3058S

29 Functions Continuous dial 4046SB Series 4 Dial Indicator Series 4 Series 4 Bezel ø 92 Description Standard contact point 11,00 For accessories and contact points, see end of dial indicators section ø92 16 ø71 9 ø6.5± ø S M ug Mass lug/plain Measuring force Graduation Scale back plate per rev. [g] [N] 4046SB 4046S , (100-0) 345/330 0,4-1,4 176,00 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 4046SB Repeatability Hysteresis error 277

30 Dial Indicator Back Plunger Type Series 1 Series 1 Series 1 This is a back plunger type dial indicator with bezel ø 39. Functions Balanced dial Continuous dial Reverse reading One Shockproof 1160T 1162T 1960T 1160T Graduation Scale per rev. 1960T 1 (plunger stroke: 4,5) 1,27 0, , T 5 1 0, , T 5 1 0, ,00 B C E F G H Measuring force Mass [N] [g] 1960T 40 22, ,7 12,8 46 0,4-1, T 40 22, ,8 43,3 0,4-1, T 40 22, ,8 43,3 0,4-1,4 DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 1960T T T Repeatability Hysteresis error ø B 1960T Delivered Delivered with factory certificate Optional accessories Description Holding bar Ø8, 81 5, Holding bar Ø8, 42 5, Holding bar Ø6, 81 4, Holding bar Ø6, 42 5,00 Description Standard contact point 11,00 21Z319 Standard contact point 3, : for Z319 : for 1160 and 1162 For accessories and contact points, see end of dial indicators section. With optional holding bar ød F G ø ø4 H øc M2.5x0.45 E 278

31 Functions One Shockproof Jeweled bearing 2960T Series T-10 Dial Indicator Back Plunger Type Series 2 Series 2 This is a back plunger type dial indicator with bezel ø Delivered Delivered with factory certificate Optional accessories Description Holding bar Ø8, 81 5, Holding bar Ø8, 42 5, Holding bar Ø6, 81 4, Holding bar Ø6, 42 5,00 Description Standard contact point 11,00 21Z319 Standard contact point 3, : for 2990T-10 21Z319 : for 2960T For accessories and contact points, see end of dial indicators section. 2990T T 2990T T Measuring force Mass Graduation Scale per rev. [N] [g] 0,1 (plunger stroke: 4) 0,14 0, ,4-1, ,00 1 (plunger stroke: 4,5) 1,27 0, ,4-1, ,00 With optional holding bar DIN 878 (1983) EN ISO 463 Errors of indication over a range of ny 1/10 ny 1/2 ny 1 fe fges fu µm µm µm µm µm µm µm µm µm 2990T T Repeatability Hysteresis error ø58 ø ø ø51 59 ø4 M T-10 ød T 0 ø ø4 M ø

32 Contact Points Ball Point : M2,5 x 0,45 Carbide Carbide waterproof type Plastic Ruby Sapphire 12,1 21Z320 8, J225 6,00 21JZ242 8, , , , J224 7,00 19,3 21Z321 13, , , J226 9, , , , , ,00 7, , , , , ,00 8,3 21Z319 3, ,00 Sø Sø ø5 ø6 Sø3 21Z319 ø6 Sø3 21Z320 ø7 ø5 Ball Point : M2,5 x 0,45 Material D Ø Carbide 1 54, Carbide 1,5 45, Steel 1,8 9, Carbide 2,5 45, Carbide 4 54,00 ø5 D 7.3 Shell Type Point - Steel : M2,5 x 0, , , , , , ,00 ø5 R2.5 For all drawings = M 2,5 x 0,45 (metric) 280

33 Contact Points ø ø ø5.2 Rz Conical Point : M2,5 x 4,5 Material Tip angle Steel , Steel , Carbide , Carbide ,00 ø ø5 N SR Needle Point - Steel : M2,5 x 4,5 N SR ,4 15 9, ,2 17 7, ,4 25 8, , ,00 ød 7 For all drawings = M 2,5 x 0,45 (metric) Cylinder Point - Carbide : M2,5 x 4,5 D Ø ,45 25, ,45 137, , , , , , , ,5 93, ,5 137, ,5 19, ,5 110, ,5 124, , , , ,00 281

34 Contact Points Spherical Point : M2,5 x 4,5 Material SR D Ø Steel 5 3 5,5 14, Carbide ,5 42, Steel 5 5 7,9 8, Steel , Carbide ,5 52,00 ød Steel SR SR ød Carbide 1.7 Flat Point - Steel : M2,5 x 4,5 Flatness D Ø , , , , , , ,00 ø5 Flatness 3 µm ød 10 3 Flatness 5µm Flat Point - Carbide : M2,5 x 4,5 Flatness D Ø Ø d , ,2 4,3 29, ,5 33, ,5 9,5 39, , , , , ,4 63, ,00 ø ø7 ø (15) ød ød 1.7 (2) ( ): ø9 ø4, (15) For all drawings = M 2,5 x 0,45 (metric) 282

35 8 Contact Points Knife Edge Point - Carbide ø4 (36.8) ,00 : M2,5 x 4,5 15 T D Blade Point - Carbide : M2,5 x 4,5 D T ,4 33, ,6 38, ,00 ever Point - Steel ,00 : M2,5 x 4, ø3 M1.4x0.3 Roller Point - Steel ,00 : M2,5 x 4,5 ø For all drawings = M 2,5 x 0,45 (metric) Interchangeable Contact Point Set 7822 : M2,5 x 4,5 Contact points included Flat point ø 5 (131365) Flat point ø 10 (101117) Needle point (101121) Spherical point (101119) Shell type point (101118) Shell type point (101387) 44,00 283

36 Extension Rods Steel Ø 5 ø ø5.2 5 = M 2,5 x 0,45 (metric) M2.5x dapter 4-48 UNF , , , B 25 5, , C 35 6, D 40 8, E 45 8, F 50 9, G 55 11, , H 65 13, , J 70 15, M 80 16, , , B ,5 10,00 Bases for Indicators Without screw , ,00 Optional accessories Description 21J269 Screw 2,00 Thickness :

37 Flat Back Plate With centre lug With magnet With laterally offset back lug With post With threaded ring a a Interchangeable Backs Description For Series Dimensions Flat Back Plate 1 (1) a = 1 4, Flat Back Plate 1 a = 2,2 4, Flat Back Plate 1 (waterproof) a = 1,5 7, Flat Back Plate 1003 a = 1 2, Flat Back Plate 2/ ID-C/ ID-S/ ID-SS a = 2,5 3,00 21ZB231 Flat Back Plate 2 (waterproof S type) a = 2,5 8, Flat Back Plate 3/ 4 a = 3 4, Back Plate with centre lug 1 (1) a = 5 9, Back Plate with centre lug 1 a = 5 9, Back Plate with centre lug for 1003 a = 5 10, Back Plate with centre lug 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS a = 5 8,00 21ZB230 Back Plate with centre lug 2 (waterproof S type) a = 5 6, Back Plate with centre lug 3/ 4 a = 5 9,00 21EZ145 Back Plate with centre lug ID-N, ID-B, GS (2) 5 16, Back Plate with magnet 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS 43, Back Plate with magnet 3/ 4 67, Back Plate with laterally offset back lug 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS 14, Back Plate with laterally offset back lug 3/ 4 62, Back Plate with post 1 44, Back Plate with post 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS 14, Back Plate with post 3/ 4 62, Back Plate with threaded ring 1 M 6 x 1 44, Back Plate with threaded ring 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS M 6 x 1 14, Back Plate with threaded ring 3/ 4 M 6x 1 54, Back Plate with adjustable stem 1 M 6 x 1 26, Back Plate with adjustable stem 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS M 6 x 1 14, Back Plate with adjustable stem 3/ 4 M 6 x 1 54, Back Plate with rack 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS 42, Back Plate set including rear lid with rack and adjustable stem 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS 75, Back Plate with Dovetail 2/ ID-C/ ID-F/ ID-H/ ID-S/ ID-SS 33,00 (1) for 1911, , 1921, 1923, , (2) for GS , , With adjustable stem With rack With rack and adjustable stem Back Plate with Dovetail For old indicator models, please contact Mitutoyo 285

38 Spindle ifting ccessories The spindle lifting lever is attached to the top end of the spindle for improved inspection efficiency when using a dial indicator mounted on a stand ZB149 21ZB150 21BZ EZ198 Spindle lifting cable Description With auto-stop function 300 length 22, Without auto-stop function 500 length 26,00 No high grade IP-Protection (e.g. IP-64) Spindle lifting handle Description Suitable for 4,8 spindle diameter 2,00 No high grade IP-Protection (e.g. IP-64) Spindle lifting lever Use for S type Series 1 F type Series 2 (former model) (up to 5 range) 9,00 21ZB149 S type Series 2, 3 and 4 (up to 10 range) 5,00 21ZB150 S type Series 2 and 3 (from 10 up to 20 range) 6,00 21ZB151 S type 7322 / ,00 21BZ205 F type Series 1 (former model) 6, F type Series 2 (former model up to 10 range) ID-C (B), (B), (B), (B), (B), , (B), (B), 6, (B), (B), (B) 21EZ198 Indicators ID-C (up to 12 range) ID-S, ID-SS 8, F type Series 2 (former model up to 20 range) F type Series 3 and 4 (former model up to 10 range) ID-S (except solar type) 7,00 No high grade IP-Protection (e.g. IP-64) Sample application for

39 Other ccessories for Dial Indicator Colour-coded Spindle Caps 9 colour-coded spindle caps are available for dial indicators with a range of 10 or less. With the exception of 2971 / 2972 / 2973 / 2976 / 2977 / Standard Water-resistant Colour Black , ,00 Blue B 4, B 4,00 Dark blue S 4, S 4,00 Green G 4, G 4,00 Orange D 4, D 4,00 Pink P 4, P 4,00 Red R 4, R 4,00 White W 4, W 4,00 Yellow Y 4, Y 4,00 Plastic cover Protection against oil and splash water. For dial indicators Series pieces per set , imit Stickers Tolerance markings. For dial indicators, Series 2 Ø 55,6 or pieces per set Colour Red 10, Green 10, Yellow 10,00 287

40 Other ccessories for Dial Indicator Crystal setter and assorted thrust pads These crystal setters and thrust pads are used to make it easy to insert round dial glasses, and offer you the following benefits: You can use them to insert round dial glasses. ssorted thrust pads for diameters: 19,5/22,5/25,5/28,5/32,5/35/38/ ,00 Tool set For repairing analogue dial indicators. 7823EU 7823EU Set configuration 7823EU : 1 - Spindle stage Pin removing bar Punch Bearing adjuster Pinion stage Reamer for pointer ø Reamer for pointer ø Reamer for pointer ø0.5 21J Pointer remover Pliers Nippers Stage for pin rest Haer Spear 21J Brush Brush Phillips and plain screwdrivers Pin vice Tweezers Phillips screwdriver Pin ø0, Pin ø0, B 25 - Pin ø01, C 26 - Nut Wooden case

41 ever Indicator Horizontal Type - 0,01 Functions Jeweled bearing Double scale spacing Coaxial counter Compact type ong stylus E up to E E E Series E E E E E E Series 513 This metric lever indicator helps you reach hard-to-access surfaces. It offers you the following benefits: It gives you easy access to shrouded surfaces that conventional indicators cannot reach. The no-clutch structure allows automatic reversal of the measuring direction. The one piece bezel and O-ring crystal seal make it highly resistant to water and dust. The glare-free flat crystal face has a scratch resistant coating. rotatable scale enables easy zero setting. Jewelled bearings and precision gears and pinions give you smooth, accurate movement and quick response. Nonmagnetic Contact point Thread M 1,7 x 0,35 For optional accessories, see end of lever indicators section Ruby contact point Basic set Graduation Scale fe fu fges Carbide stylus tip ø2 Ø D Measuring force [N] E 0,5 0, ,3 28 0, , E 0,5 0, ,3 39 0, , E 0,5 0, ,8 39 0, , E 0,8 0, ,9 28 0, , E 0,8 0, ,9 39 0, , E 1 0, ,5 39 0, , E 1,5 0, ,3 39 0, ,00 Mass [g] Basic set - Ruby contact point Graduation Scale fe fu fges Ruby stylus tip ø2 Ø D Measuring force [N] E 0,5 0, CZ210 22,3 39 0, , E 0,8 0, CZ201 20,9 39 0, , E 1 0, CZ211 44,5 39 0, ,00 Mass [g] ød Full set Graduation Scale fe fu fges Carbide stylus tip ø2 Ø D Measuring force [N] T 0,5 0, ,3 39 0, , T 0,5 0, ,8 39 0, , T 0,8 0, ,9 39 0, , T 1 0, ,5 39 0, ,00 Mass [g] 289

42 ever Indicator - Horizontal Type /0,002 Series 513 This metric lever indicator helps you reach hard-to-access surfaces. It offers you the following benefits: It gives you easy access to shrouded surfaces that conventional indicators cannot reach. The no-clutch structure allows automatic reversal of the measuring direction. The one piece bezel and O-ring crystal seal make it highly resistant to water and dust. The glare-free flat crystal face has a scratch resistant coating. rotatable scale enables easy zero setting. Jewelled bearings and precision gears and pinions give you smooth, accurate movement and quick response. Functions Jeweled bearing Coaxial counter Compact type Nonmagnetic E up to E Series 513 Contact point Thread M 1,7 x 0, E For optional accessories, see end of lever indicators section E Ruby contact point Basic set Scale fe fu fges Carbide stylus tip ø2 Ø D Graduation Measuring force [N] E 0,14 0, CZ036 12,8 39 0, , E 0,2 0, ,7 28 0, , E 0,2 0, ,7 39 0, , E 0,6 0, ,7 39 0, ,00 Mass [g] Basic set - Ruby contact point Graduation Scale fe fu fges Ruby stylus tip ø2 Ø D Measuring force [N] E 0,2 0, CZ209 14,7 39 0, ,00 Mass [g] Full set Graduation Scale fe fu fges Carbide stylus tip ø2 Ø D Measuring force [N] T 0,2 0, ,7 39 0, ,00 Mass [g] 41 ød

43 ever Indicator and Magnet Stand Series Indicator Centered, bi-directional action for automatic reversal of measuring direction. Jewelled bearings and precision gears and pinions for smooth, accurate movement and quick response. Stand Magnetic force : 150 N. Mass : 180 g Contents include E : ever Indicator 7014 : Mini Magnetic Stand Mass [g] ,00 291

44 ever Indicator Horizontal (20 Tilted Face) Type Series 513 Centered, bi-directional action for automatic reversal of measuring direction. Rotatable scale for easy zero setting. Jewelled bearings and precision gears and pinions for smooth, accurate movement and quick response. Functions Jeweled bearing Coaxial counter Nonmagnetic E E Series T T Contact point Thread M 1,7 x 0,35 Measuring force 0,3 N E E E Basic set Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] E 0,4 0, ,7 0, , E 1,6 0, ,9 0, ,00 Mass [g] Full set Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] T 0,4 0, ,7 0, , T 1,6 0, ,9 0, ,00 Mass [g] For optional accessories, see end of lever indicators section. 7.5 ø

45 Functions Jeweled bearing Nonmagnetic Series E up to T ever Indicator Vertical Type Series 513 Centered, bi-directional action for automatic reversal of measuring direction. Rotatable scale for easy zero setting. Jewelled bearings and precision gears and pinions for smooth, accurate movement and quick response. Contact point Thread M 1,7 x 0,35 For optional accessories, see end of lever indicators section E E Basic set Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] E 0,2 0, ,7 0, , E 0,8 0, ,9 0, ,00 Mass [g] Full set Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] T 0,2 0, ,7 0, , T 0,8 0, ,9 0, ,00 Mass [g] 293

46 ever Indicator Parallel Type Series 513 Centered, bi-directional action for automatic reversal of measuring direction. Rotatable scale for easy zero setting. Jewelled bearings and precision gears and pinions for smooth, accurate movement and quick response. Functions Jeweled bearing GE GT Series 513 Contact point Thread M 1,7 x 0,35 For optional accessories, see end of lever indicators section GE Basic set Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] GE 0,8 0, ,9 0, ,00 Mass [g] Full set Graduation Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] GT 0,8 0, ,9 0, ,00 Mass [g] 294

47 ever Indicator Universal Type Functions Jeweled bearing GE GT Contact point Thread M 1,4 x 0,3 Series 513 For optional accessories, see end of lever indicators section. Series 513 This level indicator makes reading much easier as you can rotate its measuring head through 360. Centered, bi-directional action for automatic reversal of measuring direction. Rotatable scale for easy zero setting. Jewelled bearings and precision gears and pinions for smooth, accurate movement and quick response. Stylus can be set at any angle while keeping the dial stationary GE Basic set Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] GE 0,8 0, , ,00 Mass [g] Full set Graduation Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] GT 0,8 0, , ,00 Mass [g] 295

48 ever Indicator Small Type Series 513 This is a small type of metric lever indicator that offers you the following benefits: The switch lever allows you to change the measuring direction. rotatable scale enables easy zero setting. Jewelled bearings and precision gears and pinions give you smooth, accurate movement and quick response. Functions Jeweled bearing E up to T Series WE WT E up to T 0 Compact type ong stylus Dustproof E T Contact point Thread M 1,7 x 0,35 For optional accessories, see end of lever indicators section E E WE E Basic set Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] E 0,14 0, ,1 0, , E 0,2 0, ,7 0, , E 0,5 0, ,8 0, , E 0,8 0, , , WE 0,8 0, CZ , , E 0,8 0, ,7 0, ,00 Mass [g] Full set Graduation Scale fe fu fges Carbide stylus tip ø2 Measuring force [N] T 0,14 0, ,1 0, , T 0,2 0, ,7 0, , T 0,5 0, ,8 0, , T 0,8 0, , , WT 0,8 0, CZ , , T 0,8 0, ,7 0, , T 1 0, ,5 0, ,00 Mass [g] ±30 ø The stylus angle should be restricted within the range ±30 (as shown above) for dustproof models WE/T. 296

49 Styli, Stems and Holders Optional accessories Description Extension for universal type 4,00 Styli for Standard models Styli for small type model Stylus length affects the scale factor of an indicator, and the styli provided to you as standard give a scale factor of unity. Styli (for Models) Standard models Small type models Ø ball point ,7 0,5 steel 21, ,9 0,5 steel 21, ,3 0,5 steel 21, ,5 0,5 steel 23, ,7 0,7 steel 17, ,9 0,7 steel 17, ,3 0,7 steel 17, ,5 0,7 steel 20, ,1 1 carbide 9,00 21CZ044 12,8 1 carbide 9, ,7 1 carbide 9, ,9 1 carbide 9,00 21CZ098 20,9 1 carbide*³ 14, ,3 1 carbide 9, carbide*² 9, ,8 1 carbide 9, ,5 1 carbide 9, ,1 2 carbide 11,00 21CZ036 12,8 2 carbide 9, ,7 2 carbide 14, ,9 2 carbide 14,00 21CZ097 20,9 2 carbide*³ 20, ,3 2 carbide 14, carbide*² 14, ,8 2 carbide 13, ,5 2 carbide 11,00 21CZ212 12,8 2 ruby 24,00 21CZ209 14,7 2 ruby 24,00 21CZ201 20,9 2 ruby 24,00 21CZ210 20,3 2 ruby 24,00 21CZ211 44,5 2 ruby 24, ,1 3 carbide 9,00 21CZ045 12,8 3 carbide 9, ,7 3 carbide 9, ,9 3 carbide 9,00 21CZ099 20,9 3 carbide 14, ,3 3 carbide 9, carbide*² 9, ,8 3 carbide 9, ,5 3 carbide 9,00 *² : Used extension *³ : For W models ø 0,5 ball-point ø 0,7 ball-point ø 1 ball-point Carbide ø 2 ball-point Carbide ø 2 ball-point Ruby ø 3 ball-point Carbide 297

50 Styli, Stems and Holders Styli, Stems and Holders Centering Holder Standard models Stem ø 8 65, Holding Bars Standard models Small type models Description x x ø 8 18,00 Centering Holder Spanner Standard models Small type models , ,00 Stems Standard models Small type models Diameter Description With Knurled Clamp Ring 12, With Knurled Clamp Ring 11, With Knurled Clamp Ring 11, , 8 With Knurled Clamp Ring 20, , 8 With Knurled Clamp Ring 23, , , , , , , Knurled Clamp Ring 6, Spanner Spanner Swivel Clamps Standard models Small type models Description For ø 4, 8 stems and dovetail 25,00 Universal Holder Standard models Small type models Stem ø 6 42, ø 8 49, ø 6 33, ø 8 49, Universal Holder 298

51 BSOUTE Digimatic Thickness Gauge Functions Series 547 ZERO/BS GO/±NG judgement Digimatic data output ON/OFF DT/HOD ock function PRESET Counting direction switchable Calculation function ccuracy ±10 µm (excluding quantizing error) Measuring force 1,5 N Scale Capacitance type BSOUTE linear encoder Max. response Unlimited speed Contact point Carbide ball M 2,5 x 0,45 (ISO/JIS type) larm ow voltage, counting value composition error, overflow error, tolerance limit setting error (only ID-C) Power supply 1 battery SR-44 Battery life approx hours Optional accessories Description Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 06DV380F USB Input Tool Direct cable 100,00 (2 m) 02ZD790F Connecting cable U-Wave 85,00 Series 547 This BSOUTE Digimatic Thickness Gauge enables you to measure tube wall thickness With indicator ID-C BS Max. measuring depth Mass Digital step Indicator [g] , BS (ID-C) ,00 Description Battery SR44 6,00 21EZ198 Spindle lifting lever (12,7 model) 8,00 ø3 ø3 ø

52 BSOUTE Digimatic Thickness Gauge Series With indicator ID-C BS Max. measuring depth Mass Digital step Type [g] ,01 30 Ceramic disc contact points , , Ceramic disc contact points and large jaw capacity , ,01 30 djustable anvil , ,01 30 Blade steel contact point ,00 Functions Series 547 ZERO/BS GO/±NG judgement Digimatic data output ON/OFF DT/HOD ock function PRESET Counting direction switchable Calculation function ccuracy ±10 µm (excluding quantizing error) Measuring force 1,5 N Scale Capacitance type BSOUTE linear encoder Parallelism 10 µm Max. response Unlimited speed Contact point M 2,5 x 0,45 (ISO/JIS type) larm ow voltage, counting value composition error, overflow error, tolerance limit setting error (ID-C only) Power supply 1 battery SR-44 Battery life approx hours Optional accessories Description Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 06DV380F USB Input Tool Direct cable 100,00 (2 m) 02ZD790F Connecting cable U-Wave 85,00 ø ø Description Battery SR44 6,00 21EZ198 Spindle lifting lever (12,7 model) 8, ø6 ø SR SR SR Concave Convex Plano-convex lens lens lens 1: Ballpoint; 2: Flatpoint; 3: nvil 300

53 BSOUTE Digimatic Thickness Gauge Functions Series 547 ZERO/BS GO/±NG judgement Digimatic data output ON/OFF DT/HOD ock function PRESET Counting direction switchable Calculation function ccuracy ±3 µm (excluding quantizing error) Measuring force 3,5 N Scale Capacitance type BSOUTE linear encoder Parallelism 3 µm Max. response Unlimited speed Contact point M 2,5 x 0,45 (ISO/JIS type) larm ow voltage, counting value composition error, overflow error, tolerance limit setting error Power supply 1 battery SR-44 Battery life approx hours Optional accessories Description Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 06DV380F USB Input Tool Direct cable 100,00 (2 m) 02ZD790F Connecting cable U-Wave 85,00 Series 547 For measuring film, paper, etc., with a resolution of 0, Max. measuring depth Mass Digital step Indicator [g] ,01 /0, BS (ID-C) ,00 Description Battery SR44 6,00 21ZB149 ifting lever 5,00 QUICK MINI Thickness Gauge Functions Series 700 ORIGIN ZERO/BS ON/OFF Series 700 This is a lightweight, palm-sized thickness gauge. ccuracy Measuring force Power supply Battery life Display Delivered ±0,02 (excluding quantizing error) 2 N Battery SR-44 approx. 20 hours CD, Character height 9 In case Description Battery SR44 6, Digital step Mass [g] , , ø5 (72.3) 29 6 (44.8)

54 Dial Indicator Thickness Gauge Series 7 This metric dial indicator thickness gauge 7331S has a lightweight design. ccuracy Refer to the list of specifications Parallelism 5 µm Description 21ZB149 ifting lever 5,00 21ZB150 ifting ever 6,00 21ZB149 : for 7301/7327/7321/7313/7315/ ZB150 : for 7305/ S 7321 ø / 7301 / 7305 ø S ø / djustable anvil Measuring force Mass Graduation ccuracy Indicator Max. measuring depth [N] [g] ,01 ±0, SB 30 1, ,00 Ceramic disc contact points Measuring force Mass Graduation ccuracy Indicator Max. measuring depth [N] [g] ,001 ±0, SB , , ,01 ±0, SB 30 1, , S ,01 ±0, , , ,01 ±0, SB ,00 Knife-edge contact point Measuring force Mass Graduation ccuracy Indicator Max. measuring depth [N] [g] ,01 ±0, SB 30 1, , SR SR3 1 SR2 ø6 ø Concave Convex Plano-convex lens lens lens 1: Ballpoint; 2: Flatpoint; 3: nvil 2 arge jaw capacity and ceramic disc contact points Measuring force Mass Graduation ccuracy Indicator Max. measuring depth [N] [g] ,01 ±0, SB 120 1, , ,01 ±0, SB ,00 Tube thicknesses - Minimum inside diameter 3,5 Measuring force Mass Graduation ccuracy Indicator Max. measuring depth [N] [g] ,01 ±0, SB 20 1, , ø3 6 6 ø ø

55 BSOUTE Digimatic Depth Gauge Functions Series 547 ZERO/BS GO/±NG judgement Digimatic data output ON/OFF DT/HOD ock function PRESET Counting direction switchable Calculation function ccuracy Refer to the list of specifications (excluding quantizing error) Measuring force 1,5 N Scale Capacitance type BSOUTE linear encoder Max. response Unlimited speed Contact point Carbide ball larm ow voltage, counting value composition error, overflow error, tolerance limit setting error Stroke 12,7 Power supply 1 battery SR-44 Battery life approx hours Extensions 5 pcs : 10, 20, 30, 30, 100 Delivered Including Box and extensions Optional accessories Description Digimatic cable (1 m) 28, Digimatic cable (2 m) 34,00 02ZD790F Connecting cable U-Wave 85,00 06DV380F USB Input Tool Direct cable (2 m) 100,00 Series 547 This BSOUTE Digimatic Indicator Depth Gauge offers you the following benefits: It is equipped with the BSOUTE Digimatic Indicator ID-C. It has a hardened, precision ground and micro-lapped reference face on its base With indicator BD Base size Mass Digital step Base flatness ccuracy [g] ,001 /0,01 2 µm ±5 µm 63,5 x , ,001 /0,01 2 µm ±5 µm 101,6 x ,00 With indicator BD Base size Mass Digital step Base flatness ccuracy [g] ,01 5 µm ±20 µm 63,5 x , ,01 5 µm ±20 µm 101,6 x ,00 Description Battery SR44 6,00 21ZB149 ifting lever 5,00 21J224 Standard contact point 17 7, , = , =101,6 303

56 Dial Indicator Depth Gauge Series 7 This rectangular base dial indicator depth gauge offers you the following benefits: Rectangular base. It has a hardened, precision ground and micro-lapped reference face on its base. Graduation 0,01 ø57 (10) (114) 12 ø8 ø ø5 SR 0.2 ø (65) (100) ø57 With horizontal indicator 1162 Base flatness ccuracy Base size Stroke ±15 µm 63,5 x 16 Probe tip Ball R = 1,5 Extension rods 10, 20, 30, 30, 100 Measuring force [N] Mass [g] 1, ,00 (10) ø16 ø8 17 ø5 ø6 SR = = (11) (35) (65) With indicator 2902SB Base flatness Stroke ccuracy Base size ±15 µm 40 x ±15 µm 63,5 x ±15 µm 101,6 x ±15 µm 100 x ±15 µm 150 x 18 Probe tip Needle R = 0,2 Ball R = 1,5 Ball R = 1,5 Ball R = 1,5 Ball R = 1,5 Extension rods 10, 20, 30, 30, , 20, 30, 30, , 20, 30, 30, , 20, 30, 30, 100 Measuring force [N] Mass [g] 1, ,00 1, ,00 1, ,00 1, ,00 1, ,00 (10) (100) ø16 ø8 17 ø5 ø6.5 ø ø57 ø57 SR 1.5 (35.7) 50 (18) (65) With indicator 2952SB Base flatness Stroke ccuracy Base size ±30 µm 63,5 x ±30 µm 101,6 x 16 Probe tip Ball R = 1,5 Ball R = 1,5 Extension rods Measuring force [N] Mass [g] 30, 60, 90 2, ,00 30, 60, 90 2, ,00 (10) (100) ø16 ø8 ø5 ø SR 1.5 (18) (35.7) (65) ø ø57 (30) (104) (65) ø16 ø8 ø6 (11) (35) 14 ø5 SR = = ø39 (64) (35) ø16 ø8 M2.5x0.45 (11) 17 (5) 22 ø5 ø6 SR = 63.5 SR

57 Dial Indicator Depth Gauge Graduation 0,01 Description Needle point 7,00 21J224 Standard contact point 17 7,00 21J226 Standard contact point 22 9,00 Series 7 This round base type dial indicator depth gauge offers you the following benefits: Round base type It has a hardened, precision ground and micro-lapped reference face on its base Circular base with indicator 2902SB. Base flatness Base size Measuring force Mass Stroke ccuracy Probe tip [N] [g] ±15 µm ø 16 Needle R = 0,2 1, , ±15 µm ø 25 Ball R = 1,5 1, , ±15 µm ø 40 Ball R = 1,5 1, ,00 ø57 ø (104) ø8 ø (65) ø (10) 17 ø3 ø5 SR ø5 SR = ø = ø40 305

58 Internal Dial Caliper Gauge Series Measuring contacts : Carbide ball ø0,6 Measuring force Graduation ccuracy (2) B (3) (1) Mass Type [N] [g] ,8/1,2 N 0,005 0,015 2,3 0,8 35 fig , Measuring contacts : Carbide ball ø1,5 Measuring force Graduation ccuracy (2) B (3) (1) Mass Type [N] [g] ,9/1,9 N 0,05 0,05 5,5 1,9 188 fig ,00 Measuring contacts : Carbide ball ø1 Measuring force Graduation ccuracy B (3) (1) Mass Type [N] [g] ,1/1,6 N 0,01 0,03 5,2 1,2 85 fig , ,1/1,6 N 0,01 0,03 7 1,2 85 fig , ,1/1,6 N 0,01 0,03 7 1,2 85 fig , ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig , Measuring contacts : Carbide ball ø2 Measuring force Graduation ccuracy B (3) (1) Mass Type [N] [g] ,9/1,9 N 0,05 0,05 8,5 2,6 192 fig , ,9/1,9 N 0,05 0,05 8,5 2,6 192 fig ,00 Measuring contacts : Carbide bevel (radius 0,1 ) Measuring force Graduation ccuracy (2) B (3) (1) Mass Type [N] [g] ,5-12,5 0,8/1,2 N 0,005 0,015 0,7 0,4 12 fig ,00 B (1) Maximum reach of contact arms over workpiece (2) Maximum groove depth (3) Minimum groove width Measuring contacts : Interchangeable, carbide ball ø1 Measuring force Graduation ccuracy B (3) (1) Mass Type [N] [g] ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1/1,6 N 0,01 0,03 8,3 1,2 85 fig ,00 Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 306

59 Internal Digimatic Caliper Gauge Functions Series 209 Mode key SET key DT key ON/OFF/0-Preset Max. reading Min. reading BS/INC switchable HOD function Data output Counting direction switchable Tolerance ED (green/red) Tolerance judgement Series 209 Power supply Delivered 2 batteries Including battery and factory certificate Optional accessories Description Holder for stand 112, Digimatic interface adapter 57, Digimatic cable (1 m) 47, Digimatic cable (2 m) 58,00 06DV380E USB Input tool Direct cable 100,00 (2 m) 02ZD790E Connecting cable U-Wave 85,00 Description Battery for remote control 10,00 (4 x R03 / ) Measuring contacts : Carbide ball ø0,6 Measuring force Graduation ccuracy (2) B (3) (1) Mass Type [N] [g] ,8-1,2 N 0,005 0,015 2,3 0,8 35 fig ,00 Measuring contacts : Carbide ball ø1,3 Measuring force Graduation ccuracy (2) B (3) (1) Mass Type [N] [g] ,2/1,7 N 0,02 0,04 5,7 1,5 127 fig ,00 Figure 1 Figure 2 Measuring contacts : Carbide ball ø1,5 Measuring force Graduation ccuracy B (3) (1) Mass Type [N] [g] /1,8 N 0,02 0,06 5,5 1,9 188 fig , ,2/1,7 N 0,02 0,04 6,5 2,5 132 fig ,00 Figure 3 Figure 4 Measuring contacts : Carbide ball ø1 Measuring force Graduation ccuracy B (3) (1) Mass Type [N] [g] ,1-1,6 N 0,01 0,03 5,2 1,2 85 fig , ,1-1,6 N 0,01 0,03 7 1,2 85 fig , ,1-1,6 N 0,01 0,03 7 1,2 85 fig , ,1-1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1-1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1-1,6 N 0,01 0,03 8,3 1,2 85 fig , ,1-1,6 N 0,01 0,03 8,3 1,2 85 fig , Measuring contacts : Carbide ball ø2 Measuring force Graduation ccuracy B (3) (1) Mass Type [N] [g] ,2/1,7 N 0,02 0,04 8,5 2,6 132 fig , ,2/1,7 N 0,02 0,04 8,5 2,6 132 fig , ,2/1,7 N 0,02 0,04 8,5 2,6 132 fig , /1,8 N 0,02 0,06 8,5 2,6 192 fig ,00 B (1) Maximum reach of contact arms over workpiece (2) Maximum groove depth (3) Minimum groove width Measuring contacts : Carbide bevel (radius 0,1 ) Measuring force Graduation ccuracy (2) B (3) (1) Mass Type [N] [g] ,5-12,5 0,8-1,2 N 0,005 0,015 0,7 0,4 12 fig ,00 307

60 External Dial Caliper Gauge Series 209 Optional accessories Description Holder for stand 112,00 Except , Measuring contacts : Ball ø2 /radius 0,5 Measuring force Graduation Hb ccuracy (2) Contact (1) Mass Type [N] radii [g] ,3/1,3 N 0,1 0,1 5 1/0,5 36 fig ,00 Measuring contacts : Carbide ball / carbide bevel Measuring force Graduation Hb ccuracy Contact (1) Mass Type [N] radii [g] ,8/1,2 N 0,005 0,015 18,8 0,4/0,75 35 fig , ,1/1,6 N 0,01 0,03 24,7 0,4/0,75 80 fig , Measuring contacts : Carbide ball ø1,5 /2 Measuring Graduation force [N] ccuracy Hb (2) Hf (3) Contact radii (1) ,8/1,7 N 0,05 0, ,5/1,5 167 fig , ,8/1,2 N 0,005 0,015 19,1 18,6 0,75/0,75 35 fig , ,1/1,6 N 0,01 0,03 24,7 24,6 0,75/0,75 85 fig , ,1/1,6 N 0,01 0,03 24,7 2,5 0,75/0,75 85 fig ,00 Type Mass [g] Measuring contacts : Carbide ball ø2 Measuring force Graduation Hb ccuracy Hf (3) (1) Mass Type [N] [g] ,8/1,7 N 0,05 0, ,3 169 fig , ,3/1,3 N 0,1 0, fig ,00 Measuring contacts : Carbide bevel Measuring force Graduation Hb ccuracy (2) Hf (3) Contact (1) Mass Type [N] radii [g] ,1/1,6 N 0,01 0,03 24,7 24,6 0,4/0,4 85 fig , Measuring contacts : Disc measuring faces ø10 Measuring force Graduation Hb ccuracy (2) Hf (3) (1) Mass Type [N] [g] ,8/1,2 N 0,005 0,02 21,7 14,8 36 fig ,00 Figures 1/2/6/7 Figure 1 Figure 2 Figure 3 Figure 4 Figures 3/4/5/8 Figure 5 Figure 6 Figure 7 Figure 8 (1) Maximum reach of contact arms over workpiece (2) Maximum penetration depth of upper contact (3) Maximum penetration depth of lower contact 308

61 External Digimatic Caliper Gauge Functions Series 209 Mode key SET key DT key ON/OFF/0-Preset Max. reading Min. reading BS/INC switchable HOD function Data output Counting direction switchable Tolerance ED (green/red) Tolerance judgement Series 209 Power supply Delivered 2 batteries Including battery and factory certificate Optional accessories Description Holder for stand 112, Digimatic interface adapter 57, Digimatic cable (1 m) 47, Digimatic cable (2 m) 58,00 06DV380E USB Input tool Direct cable 100,00 (2 m) 02ZD790E Connecting cable U-Wave 85,00 Description Battery for remote control 10,00 (4 x R03 / ) Measuring contacts : Carbide ball ø1,5 Measuring force Graduation Hb ccuracy Hf (3) (1) Mass Type [N] [g] ,8/1,2 N 0,005 0,015 19,1 18,6 35 fig , ,1/1,6 N 0,01 0,03 24,7 24,6 85 fig , ,1/1,6 N 0,01 0,03 24,7 2,5 80 fig ,00 Measuring contacts : Carbide ball ø3 Measuring force Graduation Hb ccuracy Hf (3) (1) Mass Type [N] [g] ,9/1,6 N 0,02 0, fig , ,9/1,6 N 0,02 0, ,4 116 fig , Measuring contacts : Disc measuring faces ø10 Measuring force Graduation Hb ccuracy (2) Hf (3) (1) Mass Type [N] [g] ,8/1,2 N 0,005 0,02 21,7 14,8 35 fig Measuring contacts : Disc measuring faces ø50 Measuring force Graduation Hb ccuracy (2) Hf (3) (1) Mass Type [N] [g] ,9/1,6 N 0,02 0, fig , Figure 1 Figure 2 Figure 3 Figure 4 (1) Maximum reach of contact arms over workpiece (2) Maximum penetration depth of upper contact (3) Maximum penetration depth of lower contact 309

62 12 External Digimatic Caliper Gauge Series 209 Functions Series 209 Mode key SET key DT key ON/OFF/0-Preset Max. reading Min. reading BS/INC switchable HOD function Data output Counting direction switchable Tolerance ED (green/red) Tolerance judgement Power supply Delivered 2 batteries R03 Delivered Including Battery and factory certificate Measuring contacts : Carbide ball ø3 Measuring force Graduation Hb ccuracy Hf (3) (1) Mass Type [N] [g] ,8/1,7 N 0,02 0, fig , ,8/1,7 N 0,02 0, ,3 169 fig ,00 Measuring contacts : Disc measuring faces ø50 Measuring force Graduation Hb ccuracy (2) Hf (3) (1) Mass Type [N] [g] ,8/1,7 N 0,02 0, fig ,00 Optional accessories Description Digimatic cable (1 m) 47, Digimatic cable (2 m) 58,00 06DV380E USB Input tool Direct cable 100,00 (2 m) 02ZD790E Connecting cable U-Wave 85, Digimatic interface adapter 110,00 with cover Holder for stand 112,00 Description batteries R6 () 10, ( 1 : 1 ) 3 MH Figure 1 Figure 2 Figure ( 1 : 1 ) 4 3 HM , , (1) Maximum reach of contact arms over workpiece (2) Maximum penetration depth of upper contact (3) Maximum penetration depth of lower contact

63 ccuracy Mass 1/ 2 graduation 56 g Spring Balance Series 546 This spring balance has a range of applications, offering you the following benefits: You can set micro switches, relay springs and valves. It enables you testing the measuring force of dial indicators. You can also use it for adjusting tension and compression springs. divided dial plate allows you to make measurements in both directions Dimensions in brackets refer to , , Peak Hold Graduation mn 5 mn 180, mn 10 mn 165, ,06-0,5 N 0,02 N 165, ,1-1 N 0,05 N 165, ,15-1,5 N 0,05 N 165, ,3-3 N 0,1 N 165, ,6-5 N 0,2 N 227,00 Standard Graduation mn 2 mn 201, mn 5 mn 139, mn 10 mn 124, ,06-0,5 N 0,02 N 124, ,1-1 N 0,05 N 124, ,15-1,5 N 0,05 N 124, ,3-3 N 0,1 N 124, ,6-5 N 0,2 N 206,00 Wet Film Thickness Gauge This Wet-Film Thickness Gauge enables you to measure freshly applied, still-wet coatings ,00 311

64 Coating Thickness Gauge DIGI-DERM Series 179 This coating thickness gauge lets you carry out accurate, non-destructive thickness measurements. The Coating Thickness Gauge DIGI-DERM offers you the following benefits: It enables non-destructive thickness measurement of non-magnetic coatings on magnetic substrates, or non-conductive coatings on non-magnetic substrates. Interchangeable sensors, with measuring ranges up to 15 (DIGI-DERM 740), allow you the widest range of use. It has highly accurate characteristic curves thanks to up to 50 calibration points taken during manufacture. large illuminated graphics display makes it easy to read, and you can rotate the display by 180. Scale units Statistics functions imit gauging Calibration modes µm,, mils Number of measurement values, minimum, maximum, average, standard deviation, variation coefficient, block statistics Optical and acoustic signal when measurement is outside limits Factory calibration, Zero point, 2- point- or 3-point-calibration, freely adjustable offset 157 x 75,5 x 49 Dimensions Power supply 2 x (Mignon)-batteries Standards DIN EN ISO 1461, 2064, 2178, 2360, 2808, 3882, STM B244, B499, D7091, E376 S 3894, 3, SS , SSPC-P 2 Delivered Carrying bag F FN Model Sensor type Measurement value Number of storable Mass memory measurement values [g] F5 DIGI-DERM 720 internal, fixed 10 max , FN5 DIGI-DERM 720 internal, fixed 10 max , DIGI-DERM 740 external interchangeable 100 max ,00 Material Coatings Sensor type Iron and steel : including alloyed and ferromagnetic steel Non ferrous metal : luminium, copper, zinc, austenitic steel Insulating coatings : Varnish, enamel, plastic Non-ferrous metal coating : Chromium, copper, zinc, tin Insulating coatings : Varnish, enamel, plastic Non-ferrous metal coating : Chromium, copper, zinc, tin F - - N FN - Sensors for DIGI-DERM 720 (standard) Sensor type Measuring method F5 sensor 0-5 F 5 magnetic-inductive** FN5 sensor F N ,5 FN 5 magnetic-inductive and eddy current** Sensors for DIGI-DERM 740 (optional) Sensor type Measuring method ,5 F 1,5 magnetic-inductive*** 817, F 5 magnetic-inductive** 642, F 0-1,5 magnetic-inductive and FN 1,5 N 0-0,7 eddy current*** 1125, ,7 N 07 eddy current*** 842,00 ** - Standard sensor for general applications - ccuracy according to DIN Part 13 : ±(1,5 µm+0,75% of measurement value) - Repeatability : ±(0,8 µm+0,5% of measurement value) - Smallest target surface : ø 10 *** - pplications : small parts, thin coatings - ccuracy according to DIN Part 13 : ±(1 µm+0,75% of measurement value) - Repeatability : ±(0,5 µm+0,5% of measurement value) - Smallest target surface : ø

65 Quick Guide to Precision Measuring Instruments Dial Gages and Digital Indicators Nomenclature Cap Bezel clamp imit hand Pointer Bezel Revolution counting device Stem Plunger Contact element Dial faces Continuous dial (Bi-directional graduation) Balanced dial (Multi-) Continuous dial (Standard scale spacing) Balanced dial (Multi-) Continuous dial (Reverse reading) Balanced dial (One ) Continuous dial (Double scale spacing) Balanced dial (One ) Continuous dial: For direct reading Balanced dial: For reading the difference from a reference surface Reverse reading dial: For depth or bore gage measurement One dial: For error-free reading of small differences 313