Magnetic sensor MSK5000 Incremental, digital interface, resolution 1 μm, scaling factor

Transcription

1 Incremental, digital interface, resolution μm, scaling factor 250 Profile Max. resolution μm Repeat accuracy ±0.0 mm Repeat accuracy of ± increment Status L display Works with magnetic tape M500/, MR500, MR500 Reading distance 2 mm Max pulses/revolution in combination with MR500 or MR500 (60 poles) Optionally with reference point R or flexible reference marks FR travel direction signal before design K type of connection type of connection X6 Status Ls design M elongated hole (2x K+M, 3x ZM): (enlarged illustration) 3.3 ~6 type of connection 8X 9pin SU approx design ZM Status Ls MagLine 5.2 MagLine asic

2 Incremental, digital interface, resolution μm, scaling factor Mechanical data Feature Technical data dditional information Housing synthetic material S black K design zinc diecast/aluminum M design, aluminum front cover zinc diecast ZM design Sensor/band reading distance 0. 2 mm O, I reference signals 0..5 mm R reference signal 0.4 mm FR reference signal Sensor/ring reading distance 0. 2 mm O, I reference signals 0..5 mm R reference signal able sheath PUR, suitable for dragchain use 6, 8wire ø5 0.4 mm able bending radius 5x cable diameter static 7.5x cable diameter dynamic Service life of cable >5 million cycles under the following test conditions: travel range 4.5 m travel speed 3 m/s acceleration 5 m/s 2 ambient temperature 20 ±5 Travel/circumferential speed Travel/circumferential speed Vmax [m/s] Resolution/ Scaling factor 0.00/ / / / / / Pulse interval [μs] ounting frequency [khz] lectrical data Feature Technical data dditional information Operating voltage V reverse polarity protected V without reverse polarity protection urrent consumption <25 m at 24 V, unloaded <75 m loaded Output circuit PP, L (RS422) Output signals, /,, /, I, /I, R, /R, FR, /FR Output signal level high >U 2.5 V PP >2.5 V L Output signal level low <0.8 V Pulse width of reference signal or 4 increment(s) Realtime requirement speedproportional signal output Type of connection open cable end plug connector 7/8pole Sub 9pole Signal pattern / The logical condition of signals and is not defined in reference to the index signal I or the reference signal R. It can deviate from the signal form. / I, R /I, /R I, R 90 increments Reference or index signal with 4 increments (360 ) signal length is only valid from the 5th counting step onwards. corresponding delay should be taken into consideration after switching on the operating voltage. 5 MagLine 5.2 MagLine asic

3 Incremental, digital interface, resolution μm, scaling factor Pulse interval xample: Pulse interval t = µs (i. e., the downstream unit must be able to process 250 khz) Formula for counting frequency = = 250 khz µs x 4 t System data Feature Technical data dditional information Resolution 0.00, 0.005, 0.0, 0.025, 0.05, 0. mm Scaling factor 2.5, 25, 50, 25, 250, 250 System accuracy ± ( x L) mm, L in m at T U = 20 ±0. at T U = 20 Repeat accuracy ± µm Measuring range ircumferential speed depending on scaling factor and pulse see table interval Travel speed depending on resolution and pulse interval see table mbient conditions Feature Technical data dditional information mbient temperature 70 Storage temperature Relative humidity 0 % condensation admissible M N interference resistance / immission N emitted interference / emission Protection category IP67 N Shock resistance 500 m/s 2, ms N Vibration resistance 0 m/s 2, 5 50 Hz N Pin assignment Inverted without reference signal Signal 6X 8X red orange 2 2 nc 3 3 +U brown 4 4 GN black 5 5 / yellow 6 6 / green 7 7 nc 8 nc 9 Inverted with reference signal Signal 6X 8X red orange 2 2 I,R blue 3 3 +U brown 4 4 GN black 5 5 / yellow 6 6 / green 7 7 /I, /R violet 8 8 nc 9 5 MagLine 5.2 MagLine asic

4 Incremental, digital interface, resolution μm, scaling factor Hint for mounting For systems with reference points on the magnetic tape please take care that sensor and strip are correctly aligned (see picture). Reference signal O, I R FR, Sensor/tape 2 mm.5 mm mm reading distance, Lateral offset ±2 mm ±0.5 mm ±0.5 mm, lignment error ±3 ±3 ±3, Longitudinal ± ± ± inclination, Lateral inclination ±3 ±3 ±3 Symbolic representation symbolic sensor representation 5 MagLine 5.2 MagLine asic

5 Incremental, digital interface, resolution μm, scaling factor Order Ordering information One or more system components are required: Magnetic band M500/ Magnetic ring MR500 Magnetic band ring MR Ordering table Feature Ordering data Specification dditional information Operating voltage V V esign K plastic housing M metal housing with status Ls ZM metal housing without status Ls not for operating voltage 4 and output circuit L Type of connection open cable end 6X bullet connector without mating connector 8X SU 9pin without mating connector extension cables on request able length m, in steps of m others on request Output circuit PP pushpull L Line river F Reference signal O without I periodic index index signal every 5 mm R fixed reference FR flexible reference only for ZM design and M500/ magnetic tape Linear resolution/ radial scaling factor G /250, 0.005/250, 0.0/25, 0.025/50, 0.050/25, 0./2.5 H others on request Pulse interval , 0.25, 0.5,, 2.5, 4, 8, 6, 32, 64 Order key MSK5000 F G H Scope of delivery: MSK5000, Mounting instructions, Fastening set ccessories: Installation aid Z Flexible reference mark Order key subject to technical alteration 208/02/5 4:56 5 MagLine 5.2 MagLine asic