ELECTRONIC CIRCUIT ANALYSIS LECTURE NOTES B.TECH (II YEAR II SEM) ( )

Transcription

1 ELECTRONIC CIRCUIT ANALYSIS LECTURE NOTES B.TECH (II YEAR II SEM) ( ) Prepared by: Mr. V. Shiva Rajkumar, Assistant Professor Mr. E. Mahendar Reddy, Assistant Professor Department of Electronics and Communication Engineering MALLA REDDY COLLEGE OF ENGINEERING & TECHNOLOGY (Autonomous Institution UGC, Govt. of India) Recognized under 2(f) and 12 (B) of UGC ACT 1956 (Affiliated to JNTUH, Hyderabad, Approved by AICTE - Accredited by NBA & NAAC A Grade - ISO 9001:2015 Certified) Maisammaguda, Dhulapally (Post Via. Kompally), Secunderabad , Telangana State, India

2 MALLA REDDY COLLEGE OF ENGINEERING AND TECHNOLOGY II Year B.Tech. ECE-II Sem OBJECTIVE (R15A0405) ELECTRONIC CIRCUIT ANALYSIS L T/P/D C 3 1/ - /- 3 To familiarize the student with the analysis and design of basic transistor amplifier circuits and their frequency response characteristics, feedback amplifiers, oscillators, large signal amplifiers and tuned amplifiers To demonstrate basic understanding of amplifier operation. To analyze amplifier circuits using hybrid model. UNIT - I SINGLE STAGE AMPLIFIERS: Classification of amplifiers, Transistor hybrid model, Analysis of a transistor CE, CB & CC amplifier circuit using simplified h-parameters, Analysis of CE amplifier with emitter resistance and emitter follower. Design of single stage RC coupled amplifier using BJT MULTISTAGE AMPLIFIERS: Distortion in amplifiers, Analysis of cascaded RC coupled BJT amplifier, cascode amplifier, Darlington pair, Coupling schemes-rc coupled amplifier, transformer coupled amplifier, Direct coupled Amplifier, multistage amplifier using JFET UNIT II BJT Amplifiers- Frequency Response: Logarithms, Decibels, general frequency considerations, Frequency response of an amplifier Analysis at low and High Frequencies, Hybrid-pi (π) common emitter transistor model, hybrid - π conductances and capacitances, validity of hybrid- π model, variation of hybrid π parameters, Millers theorem and its dual, the CE short circuit current gain, current gain with resistive load, gain-bandwidth product, emitter follower at high frequencies. UNIT - III FEEDBACK AMPLIFIERS: Concept of Feedback and types, transfer gain with feedback, general characteristics of negative feedback amplifiers, Effect of negative feedback on amplifiers characteristics, voltage series, current series, current shunt, and voltage shunt feedback amplifiers. OSCILLATORS: Classification of oscillators, Constituents of an oscillator, Barkhausen criterion, RC phase shift oscillator, Wein-bridge oscillator, Generalized analysis of LC oscillators- Hartley and Colpitts oscillator, Crystal oscillator,stability of oscillator, Wein bridge oscillator, Crystal oscillator, frequency stability.ujt relaxation oscillator. UNIT - IV LARGE SIGNAL AMPLIFIERS: Classification, Distortion in amplifiers, class A large signal amplifiers, transformer coupled class A power amplifier, efficiency of class A amplifier, class B power amplifier, efficiency of class B amplifier, class B push pull amplifier

3 Complementary symmetry class B push pull amplifiers, class AB push pull amplifier, class C amplifiers, class D amplifier, thermal stability, heat sink. UNIT - V TUNED AMPLIFIERS: Introduction, classification of tuned amplifiers, small signal tuned amplifier, Effect of cascading single tuned amplifier on bandwidth, Effect of cascading Double tuned amplifier on bandwidth, Staggered tuned amplifier, stability of Tuned Amplifier TEXT BOOKS: 1. Integrated Electronics-Jacob Millman and Christos C. Halkias,1991 Ed ,TMH. 2. Electronic Devices and Circuits, B.P Singh, Rekha Singh,Pearson, REFERENCE BOOKS: 1. Electronic Circuit Analysis- Rashid, Cengage Lerning, Electronic Devices and Circuit Theory-Robert L. Boylestad, Louis Nashelsky, 9Ed,2008 PE. 3. Microelectric Circuits-Sedra and Smith-5 Ed., 2009, Oxford University press. 4. Electronic Circuit Analysis-K.LalKishore, 2004, BSP. 5. Electronic Devices and Circuits-S.Salivahanan,N.Suresh Kumar,A Vallavaraj,2Ed.,2009, TMH. OUTCOMES Design and analyze the DC bias circuitry of BJT and FET. Analyze the different types of amplifiers, operation and its characteristics Design circuits like amplifiers, oscillators using the transistors diodes and oscillators

4 Based on number of stages UNIT-I Single Stage BJT Amplifier Depending upon the number of stages of Amplification, there are Single-stage amplifiers and Multi-stage amplifiers. Single-stage Amplifiers This has only one transistor circuit, which is a single stage amplification. Multi-stage Amplifiers This has multiple transistor circuit, which provides multistage amplification. Based on its output Depending upon the parameter that is amplified at the output, there are voltage and power amplifiers. Voltage Amplifiers The amplifier circuit that increases the voltage level of the input signal, is called as Voltage amplifier. Power Amplifiers The amplifier circuit that increases the power level of the input signal, is called as Power amplifier. Based on the input signals Depending upon the magnitude of the input signal applied, they can be categorized as Small signal and large signal amplifiers. Small signal Amplifiers When the input signal is so weak so as to produce small fluctuations in the collector current compared to its quiescent value, the amplifier is known as Small signal amplifier. Large signal amplifiers When the fluctuations in collector current are large i.e. beyond the linear portion of the characteristics, the amplifier is known as large signal amplifier. Based on the frequency range Depending upon the frequency range of the signals being used, there are audio and radio amplifiers. Audio Amplifiers The amplifier circuit that amplifies the signals that lie in the audio frequency range i.e. from 20Hz to 20 KHz frequency range, is called as audio amplifier. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 1

5 Power Amplifiers The amplifier circuit that amplifies the signals that lie in a very high frequency range, is called as Power amplifier. Based on Biasing Conditions Depending upon their mode of operation, there are class A, class B and class C amplifiers. Class A amplifier The biasing conditions in class A power amplifier are such that the collector current flows for the entire AC signal applied. Class B amplifier The biasing conditions in class B power amplifier are such that the collector current flows for half-cycle of input AC signal applied. Class C amplifier The biasing conditions in class C power amplifier are such that the collector current flows for less than half cycle of input AC signal applied. Class AB amplifier The class AB power amplifier is one which is created by combining both class A and class B in order to have all the advantages of both the classes and to minimize the problems they have. Based on the Coupling method Depending upon the method of coupling one stage to the other, there are RC coupled, Transformer coupled and direct coupled amplifier. RC Coupled amplifier A Multi-stage amplifier circuit that is coupled to the next stage using resistor and capacitor (RC) combination can be called as a RC coupled amplifier. Transformer Coupled amplifier A Multi-stage amplifier circuit that is coupled to the next stage, with the help of a transformer, can be called as a Transformer coupled amplifier. Direct Coupled amplifier A Multi-stage amplifier circuit that is coupled to the next stage directly, can be called as a direct coupled amplifier. Based on the Transistor Configuration Depending upon the type of transistor configuration, there are CE CB and CC amplifiers. CE amplifier The amplifier circuit that is formed using a CE configured transistor combination is called as CE amplifier. CB amplifier The amplifier circuit that is formed using a CB configured transistor combination is called as CB amplifier. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 2

6 CC amplifier The amplifier circuit that is formed using a CC configured transistor combination is called as CC amplifier. Simplified Common Emitter (CE) hybrid model hre and hoe is very small they can be neglected. Analysis of Common Emitter (CE) amplifier using simplified equivalent ckt Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 3

7 Ro= V I C Ic=hfeIb Apply KVL input side RsIb+hieIb=0 => (Rs+hie)Ib=0 It is possible only when Ib=0 =>Ic=hfeIb=0 Ro= Response of BJT amplifier in Common Collector (CC) configuration using simplified hybrid model in CE configuration Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 4

8 Common Base (CB) Configuration Comparison of CE,CC and CB Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 5

9 CE amplifier with emitter resistance RE AI without RE = -hfe (1 a) Current gain is unaltered by one addition of amplifier resistance. Ri without RE = hie (2a) This is a desirable effect produced by the addition of resistance RE i.e. the input resistance is higher. Normally, (1+hfe) RE>>hie Also hfe>> 1 Then, So, the gain of the amplifier becomes the radio of two resistances, and hence the gain is stabilized Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 6

10 Multi-stage amplifiers In practical applications, the output of a single state amplifier is usually insufficient, though it is a voltage or power amplifier. Hence they are replaced by Multi-stage transistor amplifiers. In Multi-stage amplifiers, the output of first stage is coupled to the input of next stage using a coupling device. These coupling devices can usually be a capacitor or a transformer. This process of joining two amplifier stages using a coupling device can be called ascascading. The following figure shows a two-stage amplifier connected in cascade. The overall gain is the product of voltage gain of individual stages. V 2 AV=AV1 AV2= V1 Vo V Vo 2 V1 Where AV = Overall gain, AV1 = Voltage gain of 1 st stage, and AV2= Voltage gain of 2 nd stage. If there is n number of stages, the product of voltage gains of those n stages will be the overall gain of that multistage amplifier circuit. Purpose of coupling device The basic purposes of a coupling device are To transfer the AC from the output of one stage to the input of next stage. To block the DC to pass from the output of one stage to the input of next stage, which means to isolate the DC conditions. Types of Coupling Joining one amplifier stage with the other in cascade, using coupling devices form a Multistage amplifier circuit. There are four basic methods of coupling, using these coupling devices such as resistors, capacitors, transformers etc. Let us have an idea about them. Resistance-Capacitance Coupling Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 7

11 This is the mostly used method of coupling, formed using simple resistorcapacitor combination. The capacitor which allows AC and blocks DC is the main coupling element used here. The coupling capacitor passes the AC from the output of one stage to the input of its next stage. While blocking the DC components from DC bias voltages to effect the next stage. Let us get into the details of this method of coupling in the coming chapters. Impedance Coupling The coupling network that uses inductance and capacitance as coupling elements can be called as Impedance coupling network. In this impedance coupling method, the impedance of coupling coil depends on its inductance and signal frequency which is jwl. This method is not so popular and is seldom employed. Transformer Coupling The coupling method that uses a transformer as the coupling device can be called as Transformer coupling. There is no capacitor used in this method of coupling because the transformer itself conveys the AC component directly to the base of second stage. The secondary winding of the transformer provides a base return path and hence there is no need of base resistance. This coupling is popular for its efficiency and its impedance matching and hence it is mostly used. Direct Coupling If the previous amplifier stage is connected to the next amplifier stage directly, it is called as direct coupling. The individual amplifier stage bias conditions are so designed that the stages can be directly connected without DC isolation. The direct coupling method is mostly used when the load is connected in series, with the output terminal of the active circuit element. For example, head-phones, loud speakers etc. Role of Capacitors in Amplifiers Other than the coupling purpose, there are other purposes for which few capacitors are especially employed in amplifiers. To understand this, let us know about the role of capacitors in Amplifiers. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 8

12 The Input Capacitor Cin The input capacitor Cin present at the initial stage of the amplifier, couples AC signal to the base of the transistor. This capacitor Cin if not present, the signal source will be in parallel to resistor R2 and the bias voltage of the transistor base will be changed. Hence Cin allows, the AC signal from source to flow into input circuit, without affecting the bias conditions. The Emitter By-pass Capacitor Ce The emitter by-pass capacitor Ce is connected in parallel to the emitter resistor. It offers a low reactance path to the amplified AC signal. In the absence of this capacitor, the voltage developed across RE will feedback to the input side thereby reducing the output voltage. Thus in the presence of Ce the amplified AC will pass through this. Coupling Capacitor CC The capacitor CC is the coupling capacitor that connects two stages and prevents DC interference between the stages and controls the operating point from shifting. This is also called as blocking capacitor because it does not allow the DC voltage to pass through it. In the absence of this capacitor, RC will come in parallel with the resistance R1 of the biasing network of the next stage and thereby changing the biasing conditions of the next stage. Amplifier Consideration For an amplifier circuit, the overall gain of the amplifier is an important consideration. To achieve maximum voltage gain, let us find the most suitable transistor configuration for cascading. CC Amplifier Its voltage gain is less than unity. CB Amplifier It is not suitable for intermediate stages. Its voltage gain is less than unity. Hence not suitable for cascading. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 9

13 CE Amplifier Its voltage gain is greater than unity. Voltage gain is further increased by cascading. The characteristics of CE amplifier are such that, this configuration is very suitable for cascading in amplifier circuits. Hence most of the amplifier circuits use CE configuration. Two Stage CE-CE Cascade Amplifier h-parameter equivalent circuit Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 10

14 Cascode Amplifier AC equivalent circuit h-parameter equivalent circuit Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 11

15 Darlington pair Darlington pair 1- Two emitter follower stages in cascade with infinite emitter resistance in the first stage constitute a Darlington circuit. Second Stage Let us assume, hoe RL< 0.1 Also hfe>> 1 Ri2 = hie + (1+hfe) RL ~ hie + hfe RL hfe RL (2) RL1 = Ri2 = hfe RL (3) First Stage hoerl1 = hoehferl< 0.1. If this inequality is satisfied, then we can use simplified equivalent ckt in the first stage.using exact solution Ri1 = hie + hrc AI1 RL1 Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 12

16 For emitter follower Ri = hie + (1+hfe) RL =hie + hfe RL Overall current gain Darlington ckt, AV = AV1 AV2 Effect of biasing network on the input resistance of emitter follower or Darlington ckt. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 13

17 Effective input resistance Ri = R1 R2 Ri where Ri is a large input resistance of emitter follower or Darlington ckt. Ri = RB Ri ~ RB Emitter follower with Boot Strap Biasing The reactance offered by the capacitor is very low for all frequencies. R3 can be replaced by Miller s theorem Effective output resistance RL = RO R3O RB Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 14

18 Coupling Schemes Two-stage RC Coupled Amplifier The resistance-capacitance coupling is, in short termed as RC coupling. This is the mostly used coupling technique in amplifiers. Construction of a Two-stage RC Coupled Amplifier The constructional details of a two-stage RC coupled transistor amplifier circuit are as follows. The two stage amplifier circuit has two transistors, connected in CE configuration and a common power supply VCC is used. The potential divider network R1 and R2and the resistor Re form the biasing and stabilization network. The emitter by-pass capacitor Ce offers a low reactance path to the signal. The resistor RL is used as a load impedance. The input capacitor Cin present at the initial stage of the amplifier couples AC signal to the base of the transistor. The capacitor CC is the coupling capacitor that connects two stages and prevents DC interference between the stages and controls the shift of operating point. The figure below shows the circuit diagram of RC coupled amplifier. Operation of RC Coupled Amplifier When an AC input signal is applied to the base of first transistor, it gets amplified and appears at the collector load RL which is then passed through the coupling capacitor CC to the next stage. This becomes the input of the next stage, whose amplified output again appears across its collector load. Thus the signal is amplified in stage by stage action. The important point that has to be noted here is that the total gain is less than the product of the gains of individual stages. This is because when a second stage is made to follow the first stage, the effective load resistance of the first stage is reduced due to the shunting Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 15

19 effect of the input resistance of the second stage. Hence, in a multistage amplifier, only the gain of the last stage remains unchanged. As we consider a two stage amplifier here, the output phase is same as input. Because the phase reversal is done two times by the two stage CE configured amplifier circuit. Frequency Response of RC Coupled Amplifier Frequency response curve is a graph that indicates the relationship between voltage gain and function of frequency. The frequency response of a RC coupled amplifier is as shown in the following graph. From the above graph, it is understood that the frequency rolls off or decreases for the frequencies below 50Hz and for the frequencies above 20 KHz. whereas the voltage gain for the range of frequencies between 50Hz and 20 KHz is constant. We know that, XC=1/2πfc It means that the capacitive reactance is inversely proportional to the frequency. At Low frequencies (i.e. below 50 Hz) The capacitive reactance is inversely proportional to the frequency. At low frequencies, the reactance is quite high. The reactance of input capacitor Cin and the coupling capacitor CC are so high that only small part of the input signal is allowed. The reactance of the emitter by pass capacitor CE is also very high during low frequencies. Hence it cannot shunt the emitter resistance effectively. With all these factors, the voltage gain rolls off at low frequencies. At High frequencies (i.e. above 20 KHz):Again considering the same point, we know that the capacitive reactance is low at high frequencies. So, a capacitor behaves as a short Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 16

20 circuit, at high frequencies. As a result of this, the loading effect of the next stage increases, which reduces the voltage gain. Along with this, as the capacitance of emitter diode decreases, it increases the base current of the transistor due to which the current gain (β) reduces. Hence the voltage gain rolls off at high frequencies. At Mid-frequencies (i.e. 50 Hz to 20 KHz) The voltage gain of the capacitors is maintained constant in this range of frequencies, as shown in figure. If the frequency increases, the reactance of the capacitor CC decreases which tends to increase the gain. But this lower capacitance reactive increases the loading effect of the next stage by which there is a reduction in gain. Due to these two factors, the gain is maintained constant. Advantages of RC Coupled Amplifier The following are the advantages of RC coupled amplifier. The frequency response of RC amplifier provides constant gain over a wide frequency range, hence most suitable for audio applications. The circuit is simple and has lower cost because it employs resistors and capacitors which are cheap. It becomes more compact with the upgrading technology. Disadvantages of RC Coupled Amplifier The following are the disadvantages of RC coupled amplifier. The voltage and power gain are low because of the effective load resistance. They become noisy with age. Due to poor impedance matching, power transfer will be low. Applications of RC Coupled Amplifier The following are the applications of RC coupled amplifier. They have excellent audio fidelity over a wide range of frequency. Widely used as Voltage amplifiers Due to poor impedance matching, RC coupling is rarely used in the final stages. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 17

21 We have observed that the main drawback of RC coupled amplifier is that the effective load resistance gets reduced. This is because, the input impedance of an amplifier is low, while its output impedance is high. When they are coupled to make a multistage amplifier, the high output impedance of one stage comes in parallel with the low input impedance of next stage. Hence, effective load resistance is decreased. This problem can be overcome by a transformer coupled amplifier. In a transformer-coupled amplifier, the stages of amplifier are coupled using a transformer. Let us go into the constructional and operational details of a transformer coupled amplifier. Construction of Transformer Coupled Amplifier The amplifier circuit in which, the previous stage is connected to the next stage using a coupling transformer, is called as Transformer coupled amplifier. The coupling transformer T1 is used to feed the output of 1 st stage to the input of 2 nd stage. The collector load is replaced by the primary winding of the transformer. The secondary winding is connected between the potential divider and the base of 2 nd stage, which provides the input to the 2 nd stage. Instead of coupling capacitor like in RC coupled amplifier, a transformer is used for coupling any two stages, in the transformer coupled amplifier circuit. The figure below shows the circuit diagram of transformer coupled amplifier. The potential divider network R1 and R2 and the resistor Re together form the biasing and stabilization network. The emitter by-pass capacitor Ce offers a low reactance path to the signal. The resistor RL is used as a load impedance. The input capacitor Cin present at the initial stage of the amplifier couples AC signal to the base of the transistor. The capacitor Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 18

22 CC is the coupling capacitor that connects two stages and prevents DC interference between the stages and controls the shift of operating point. Operation of Transformer Coupled Amplifier When an AC signal is applied to the input of the base of the first transistor then it gets amplified by the transistor and appears at the collector to which the primary of the transformer is connected. The transformer which is used as a coupling device in this circuit has the property of impedance changing, which means the low resistance of a stage (or load) can be reflected as a high load resistance to the previous stage. Hence the voltage at the primary is transferred according to the turns ratio of the secondary winding of the transformer. This transformer coupling provides good impedance matching between the stages of amplifier. The transformer coupled amplifier is generally used for power amplification. Frequency Response of Transformer Coupled Amplifier The figure below shows the frequency response of a transformer coupled amplifier. The gain of the amplifier is constant only for a small range of frequencies. The output voltage is equal to the collector current multiplied by the reactance of primary. At low frequencies, the reactance of primary begins to fall, resulting in decreased gain. At high frequencies, the capacitance between turns of windings acts as a bypass condenser to reduce the output voltage and hence gain. So, the amplification of audio signals will not be proportionate and some distortion will also get introduced, which is called as Frequency distortion. Advantages of Transformer Coupled Amplifier An excellent impedance matching is provided. Gain achieved is higher. There will be no power loss in collector and base resistors. Efficient in operation. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 19

23 Disadvantages of Transformer Coupled Amplifier The following are the disadvantages of a transformer coupled amplifier Though the gain is high, it varies considerably with frequency. Hence a poor frequency response. Frequency distortion is higher. Transformers tend to produce hum noise. Transformers are bulky and costly. Applications The following are the applications of a transformer coupled amplifier Mostly used for impedance matching purposes. Used for Power amplification. Used in applications where maximum power transfer is needed. The other type of coupling amplifier is the direct coupled amplifier, which is especially used to amplify lower frequencies, such as amplifying photo-electric current or thermo-couple current or so. Direct Coupled Amplifier As no coupling devices are used, the coupling of the amplifier stages is done directly and hence called as Direct coupled amplifier. Construction The figure below indicates the three stage direct coupled transistor amplifier. The output of first stage transistor T1 is connected to the input of second stage transistor T2. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 20

24 The transistor in the first stage will be an NPN transistor, while the transistor in the next stage will be a PNP transistor and so on. This is because; the variations in one transistor tend to cancel the variations in the other. The rise in the collector current and the variation in β of one transistor gets cancelled by the decrease in the other. Operation The input signal when applied at the base of transistor T1, it gets amplified due to the transistor action and the amplified output appears at the collector resistor Rc of transistor T1. This output is applied to the base of transistor T2 which further amplifies the signal. In this way, a signal is amplified in a direct coupled amplifier circuit. Advantages The advantages of direct coupled amplifier are as follows. The circuit arrangement is simple because of minimum use of resistors. The circuit is of low cost because of the absence of expensive coupling devices. Disadvantages The disadvantages of direct coupled amplifier are as follows. It cannot be used for amplifying high frequencies. Applications The operating point is shifted due to temperature variations. Low frequency amplifications. Low current amplifications. Comparisons S.No Particular RC Coupling Transformer Direct Coupling 1 Frequency Excellent in audio Poor Best 2 Cost Less More Least 3 Space and Less More Least 4 Impedance Not good Excellent Good 5 Use For voltage For Power For amplifying Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 21

25 UNIT-II BJT Amplifiers- Frequency Response Under reverse bias condition the capacitance at the junction is called transition or space charge capacitance. Under forward bias condition the capacitance is called diffusion or storage capacitance. At high frequencies, BJT cannot be analysed by h-parameters. Giacolleto model - hybrid π equivalent ckt Desirable fractures of hybrid π equivalent circuit (ckt) (1) The value of components in the equivalent ckt. are independent of frequencies. (2) The values of all the resistive components in the equivalent ckt. can be determined from the known or Specified values of h-parameters at low frequencies. (3) The results obtained by using this equivalent ckt. Agrees with the experimental result. The components of the equivalent ckt. exist in the form of π hence the name. For small signal behaviour the transistor at its input port behaves as a resistor. The output port is a dependent current source. Because the base (B) is lightly doped all the depletion region lies entirely in the Base region. So, when the collector. voltage is increased the depletion region in the base increases. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 22

26 rce --> This resistance is added to compensate for the change in IC due to change in VCE. The High frequency model parameters of a BJT in terms of low frequency hybrid parameters is given below Transconductance gm = Ic/Vt Internal Base node to emitter resistance rb e = hfe/ gm = (hfe* Vt )/ Ic Internal Base node to collector resistance rb e = (hre* rb c) / (1- hre) assuming hre << 1 it reduces to rb e = (hre* rb c) Base spreading resistance rbb = hie rb e = hie (hfe* Vt )/ Ic Collector to emitter resistance rce = 1 / ( hoe (1+ hfe)/rb c) The CE short circuit current gain (Ai) (1) is in shunt with short circuit and behaves as open circuit and hence is removed from the equivalent circuit. (2) rb e rb c rb e Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 23

27 CC Ce = CC + Ce (3) Current delivered directly to the output from input though rb c& CC is negligibly small compared to dependent current source gmvb e Under these assumptions the simplified hybrid model of CE amplifier. At f = 0, Ai = - hfe Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 24

28 The parameter ft: The frequency at which the magnitude short ckt. current gain of CE amplifier reduces to unity is defined as frequency ft ft --> Gain bandwidth product of an amplifier. Ai = at f = ft Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 25

29 Current gain of CE amplifier with Resistive Load Assumptions : 1) Both input and output loop contain RC ckt. the RC product of input loop is larger than that of output loop and determines the bandwidth of (3dB frequency) of the amplifier. Consequently the Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 26

30 (2) For practical amplifier RL< 2KΩ rce = 80K (3) Vce = -gm Vb e RL Typical value of gm = 50mA/V & RL = 2KΩ. Putting these value K = In the input loop (4) C = Ce + CC (1-K) = Ce + CC (1 + gm) Final equivalent ckt. At f = 0, AI = -hfe Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 27

31 Current gain of CE amplifier taking source resistance into account AIS= (1) * (2) For f = 0, jωc AISO= -gmrs From (4) where gb'e<< G'S Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 28

32 So, to summarize C = Ce + CC (1 + gm RL) (5) (b) Taking source resistance into account C = Ce + CC (1 + gmrl) (9) Voltage gain taking source resistance into consideration R =RS + rbb' C = Ce + CC (1 + gmrl) Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 29

33 Where f = 0 Voltage Gain Bandwidth Product Problem - = fh = 50 * 10 6 Hz, RL= 500Ω, hfe = 100, gm = 100mA/V, rbb = 100Ω, CC = 1PF, ft = 400MHz, find RS =? C = Ce + CC (1 + gmrl) RS = 449 Ω Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 30

34 Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 31 Bandwidth of a multistage amplifier The range of frequencies which are amplified without much variation in gain is called bandwidth of amplifiers. Human ears are insensitive to the variation of power gain of about 3dB. Hence, frequency range from lower 3dB to upper 3dB is considered as bandwidth of single stage amplifier. Bandwidth of single stage amplifier. Bandwidth (BW) = fh fl ~ fh Lower 3dB frequency of multistage amplifier The lower 3db frequency of n identical cascaded stages as fl(n).it is the frequency for which the overall gain falls to 2 1 (3 db) of its midband value n L L n f f n L L n f f Squaring on both sides we get n L L n f f Taking n th root on both sides n L L n f f n L L n f f Taking square root on both sides

35 Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page n L L n L L f n f n f f Higher 3dB frequency of multistage amplifier The lower 3db frequency of n identical cascaded stages as fh(n).it is the frequency for which the overall gain falls to 2 1 (3 db) of its midband value n H H f n f n H H f n f Squaring on both sides we get n H H f n f Taking n th root on both sides n H H f n f n H H f n f Taking square root on both sides n H H n H H f n f f n f

36 Feedback Amplifier UNIT-III Feedback Amplifier & Oscillator A practical amplifier has a gain of nearly one million i.e. its output is one million times the input. Consequently, even a casual disturbance at the input will appear in the amplified form in the output. There is a strong tendency in amplifiers to introduce hum due to sudden temperature changes or stray electric and magnetic fields. Therefore, every high gain amplifier tends to give noise along with signal in its output. The noise in the output of an amplifier is undesirable and must be kept to as small a level as possible. The noise level in amplifiers can be reduced considerably by the use of negative feedback i.e. by injecting a fraction of output in phase opposition to the input signal. The object of this chapter is to consider the effects and methods of providing negative feedback in transistor amplifiers. Ideally an amplifier should reproduce the input signal, with change in magnitude and with or without change in phase. But some of the short comings of the amplifier circuit are 1. Change in the value of the gain due to variation in supplying voltage, temperature or due to components. 2. Distortion in wave-form due to non linearities in the operating characters of the Amplifying device. 3. The amplifier may introduce noise (undesired signals) The above drawbacks can be minimizing if we introduce feedback CLASSIFICATION OF AMPLIFIERS Amplifiers can be classified broadly as, 1. Voltage amplifiers. 2. Current amplifiers. 3. Transconductance amplifiers. 4. Transresistance amplifiers. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 33

37 Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 34

38 Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 35

39 Concept of Feedback An amplifier circuit simply increases the signal strength. But while amplifying, it just increases the strength of its input signal whether it contains information or some noise along with information. This noise or some disturbance is introduced in the amplifiers because of their strong tendency to introduce hum due to sudden temperature changes or stray electric and magnetic fields. Therefore, every high gain amplifier tends to give noise along with signal in its output, which is very undesirable. The noise level in the amplifier circuits can be considerably reduced by using negative feedback done by injecting a fraction of output in phase opposition to the input signal. Principle of Feedback Amplifier A feedback amplifier generally consists of two parts. They are theamplifier and the feedback circuit. The feedback circuit usually consists of resistors. The concept of feedback amplifier can be understood from the following figure. From the above figure, the gain of the amplifier is represented as A. the gain of the amplifier is the ratio of output voltage V o to the input voltage V i. the feedback network extracts a voltage Vf = β Vo from the output Vo of the amplifier. This voltage is added for positive feedback and subtracted for negative feedback, from the signal voltage Vs. Now, Vi=Vs+Vf=Vs+βVo Vi=Vs Vf=Vs βvo The quantity β = Vf/Vo is called as feedback ratio or feedback fraction. Let us consider the case of negative feedback. The output Vomust be equal to the input voltage (Vs - βvo) multiplied by the gain A of the amplifier. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 36

40 Hence, (Vs βvo)a=vo Or AVs AβVo=Vo Or AVs=Vo(1+Aβ) Therefore, Vo A Vs 1 A Let Af be the overall gain (gain with the feedback) of the amplifier. This is defined as the ratio of output voltage Vo to the applied signal voltage Vs, i.e., A Af 1 A The equation of gain of the feedback amplifier, with positive feedback is given by A Af 1 A These are the standard equations to calculate the gain of feedback amplifiers. Types of Feedbacks The process of injecting a fraction of output energy of some device back to the input is known as Feedback. It has been found that feedback is very useful in reducing noise and making the amplifier operation stable. Depending upon whether the feedback signal aids or opposes the input signal, there are two types of feedbacks used. Positive Feedback The feedback in which the feedback energy i.e., either voltage or current is in phase with the input signal and thus aids it is called aspositive feedback. Both the input signal and feedback signal introduces a phase shift of 180 o thus making a 360 o resultant phase shift around the loop, to be finally in phase with the input signal. Though the positive feedback increases the gain of the amplifier, it has the disadvantages such as Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 37

41 Increasing distortion Instability It is because of these disadvantages the positive feedback is not recommended for the amplifiers. If the positive feedback is sufficiently large, it leads to oscillations, by which oscillator circuits are formed. Negative Feedback The feedback in which the feedback energy i.e., either voltage or current is out of phase with the input and thus opposes it, is called as negative feedback. In negative feedback, the amplifier introduces a phase shift of 180 o into the circuit while the feedback network is so designed that it produces no phase shift or zero phase shift. Thus the resultant feedback voltage Vf is 180 o out of phase with the input signal Vin. Though the gain of negative feedback amplifier is reduced, there are many advantages of negative feedback such as Stability of gain is improved Reduction in distortion Reduction in noise Increase in input impedance Decrease in output impedance Increase in the range of uniform application It is because of these advantages negative feedback is frequently employed in amplifiers. Negative feedback in an amplifier is the method of feeding a portion of the amplified output to the input but in opposite phase. The phase opposition occurs as the amplifier provides 180 o phase shift whereas the feedback network doesn t. While the output energy is being applied to the input, for the voltage energy to be taken as feedback, the output is taken in shunt connection and for the current energy to be taken as feedback, the output is taken in series connection. There are two main types of negative feedback circuits. They are Negative Voltage Feedback Negative Current Feedback Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 38

42 Negative Voltage Feedback In this method, the voltage feedback to the input of amplifier is proportional to the output voltage. This is further classified into two types Voltage-series feedback Voltage-shunt feedback Negative Current Feedback In this method, the voltage feedback to the input of amplifier is proportional to the output current. This is further classified into two types. Current-series feedback Current-shunt feedback Let us have a brief idea on all of them. Voltage-Series Feedback In the voltage series feedback circuit, a fraction of the output voltage is applied in series with the input voltage through the feedback circuit. This is also known as shunt-driven series-fed feedback, i.e., a parallel-series circuit. The following figure shows the block diagram of voltage series feedback, by which it is evident that the feedback circuit is placed in shunt with the output but in series with the input. As the feedback circuit is connected in shunt with the output, the output impedance is decreased and due to the series connection with the input, the input impedance is increased. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 39

43 Voltage-Shunt Feedback In the voltage shunt feedback circuit, a fraction of the output voltage is applied in parallel with the input voltage through the feedback network. This is also known as shunt-driven shunt-fed feedback i.e., a parallel-parallel proto type. The below figure shows the block diagram of voltage shunt feedback, by which it is evident that the feedback circuit is placed in shunt with the output and also with the input. As the feedback circuit is connected in shunt with the output and the input as well, both the output impedance and the input impedance are decreased. Current-Series Feedback In the current series feedback circuit, a fraction of the output voltage is applied in series with the input voltage through the feedback circuit. This is also known as series-driven series-fed feedback i.e., a series-series circuit. The following figure shows the block diagram of current series feedback, by which it is evident that the feedback circuit is placed in series with the output and also with the input. As the feedback circuit is connected in series with the output and the input as well, both the output impedance and the input impedance are increased. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 40

44 Current-Shunt Feedback In the current shunt feedback circuit, a fraction of the output voltage is applied in series with the input voltage through the feedback circuit. This is also known as series-driven shunt-fed feedback i.e., a series-parallel circuit. The below figure shows the block diagram of current shunt feedback, by which it is evident that the feedback circuit is placed in series with the output but in parallel with the input. As the feedback circuit is connected in series with the output, the output impedance is increased and due to the parallel connection with the input, the input impedance is decreased. Let us now tabulate the amplifier characteristics that get affected by different types of negative feedbacks. Characteristics Types of Feedback Voltage-Series Voltage-Shunt Current-Series Current-Shunt Voltage Gain Decreases Decreases Decreases Decreases Bandwidth Increases Increases Increases Increases Input resistance Increases Decreases Increases Decreases Output resistance Decreases Decreases Increases Increases Harmonic distortion Decreases Decreases Decreases Decreases Noise Decreases Decreases Decreases Decreases Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 41

45 EXPRESSION FOR INPUT RESISTANCE RI WITH VOLTAGE SERIES FEEDBACK In this circuit Av represents the open circuit voltage gain taking Rs into account Voltage series feedback VS Rif Ii Apply KVL to the input side circuit Vs-IiRi-Vf=0 Vs=IiRi+Vf=IiRi+βVo The output voltage Vo is given as V o Where AV v irl R R A o V R A o L V R L R L A V I i R i A V V i Av represents the open circuit voltage gain without feedback AV represents the open circuit voltage gain without feedback taking the load RL into account. Vs=IiRi+βAvIiRi VS Rif =R i +βavri Ii Rif=Ri(1+βAv) Similarly we can find Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 42

46 Advantages of Negative Feedback 1. Stabilization of gain make the gain less sensitive to changes in circuit components e.g. due to changes in temperature. 2. Reduce non-linear distortion make the output proportional to the input, keeping the gain constant, independent of signal level. 3. Reduce the effect of noise minimize the contribution to the output of unwanted signals generated in circuit components or extraneous interference. 4. Extend the bandwidth of the amplifier Reduce the gain and increase the bandwidth 5. Modification the input and output impedances Oscillators raise or lower the input and output impedances by selection of the appropriate feedback topology. An oscillator generates output without any ac input signal. An electronic oscillator is a circuit which converts dc energy into ac at a very high frequency. An amplifier with a positive feedback can be understood as an oscillator. Amplifier vs. Oscillator An amplifier increases the signal strength of the input signal applied, whereas an oscillator generates a signal without that input signal, but it requires dc for its operation. This is the main difference between an amplifier and an oscillator. Take a look at the following illustration. It clearly shows how an amplifier takes energy from d.c. power source and converts it into a.c. energy at signal frequency. An oscillator produces an oscillating a.c. signal on its own. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 43

47 The frequency, waveform, and magnitude of a.c. power generated by an amplifier, is controlled by the a.c. signal voltage applied at the input, whereas those for an oscillator are controlled by the components in the circuit itself, which means no external controlling voltage is required. Alternator vs. Oscillator An alternator is a mechanical device that produces sinusoidal waves without any input. This a.c. generating machine is used to generate frequencies up to 1000Hz. The output frequency depends on the number of poles and the speed of rotation of the armature. The following points highlight the differences between an alternator and an oscillator An alternator converts mechanical energy to a.c. energy, whereas the oscillator converts d.c. energy into a.c. energy. An oscillator can produce higher frequencies of several MHz whereas an alternator cannot. An alternator has rotating parts, whereas an electronic oscillator doesn t. It is easy to change the frequency of oscillations in an oscillator than in an alternator. Oscillators can also be considered as opposite to rectifiers that convert a.c. to d.c. as these convert d.c. to a.c. Classification of Oscillators Electronic oscillators are classified mainly into the following two categories Sinusoidal Oscillators The oscillators that produce an output having a sine waveform are called sinusoidal or harmonic oscillators. Such oscillators can provide output at frequencies ranging from 20 Hz to 1 GHz. Non-sinusoidal Oscillators The oscillators that produce an output having a square, rectangular or saw-tooth waveform are called non-sinusoidal or relaxation oscillators. Such oscillators can provide output at frequencies ranging from 0 Hz to 20 MHz. Sinusoidal Oscillators Sinusoidal oscillators can be classified in the following categories Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 44

48 Tuned Circuit Oscillators These oscillators use a tuned-circuit consisting of inductors (L) and capacitors (C) and are used to generate high-frequency signals. Thus they are also known as radio frequency R.F. oscillators. Such oscillators are Hartley, Colpitts, Clapp-oscillators etc. RC Oscillators There oscillators use resistors and capacitors and are used to generate low or audio-frequency signals. Thus they are also known as audiofrequency (A.F.) oscillators. Such oscillators are Phase shift and Wein-bridge oscillators. Crystal Oscillators These oscillators use quartz crystals and are used to generate highly stabilized output signal with frequencies up to 10 MHz. The Piezo oscillator is an example of a crystal oscillator. Negative-resistance Oscillator These oscillators use negative-resistance characteristic of the devices such as tunnel devices. A tuned diode oscillator is an example of a negative-resistance oscillator. Nature of Sinusoidal Oscillations The nature of oscillations in a sinusoidal wave is generally of two types. They are damped and undamped oscillations. Damped Oscillations The electrical oscillations whose amplitude goes on decreasing with time are called as Damped Oscillations. The frequency of the damped oscillations may remain constant depending upon the circuit parameters. Damped oscillations are generally produced by the oscillatory circuits that produce power losses and doesn t compensate if required. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 45

49 Undamped Oscillations The electrical oscillations whose amplitude remains constant with time are called as Undamped Oscillations. The frequency of the Undamped oscillations remains constant. Undamped oscillations are generally produced by the oscillatory circuits that produce no power losses and follow compensation techniques if any power losses occur. An amplifier with positive feedback produces its output to be in phase with the input and increases the strength of the signal. Positive feedback is also called as degenerative feedback ordirect feedback. This kind of feedback makes a feedback amplifier, an oscillator. The use of positive feedback results in a feedback amplifier having closed-loop gain greater than the open-loop gain. It results in instability and operates as an oscillatory circuit. An oscillatory circuit provides a constantly varying amplified output signal of any desired frequency. The Barkhausen Criterion With the knowledge we have till now, we understood that a practical oscillator circuit consists of a tank circuit, a transistor amplifier circuit and a feedback circuit. so, let us now try to brush up the concept of feedback amplifiers, to derive the gain of the feedback amplifiers. Principle of Feedback Amplifier A feedback amplifier generally consists of two parts. They are theamplifier and the feedback circuit. The feedback circuit usually consists of resistors. The concept of feedback amplifier can be understood from the following figure below. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 46

50 From the above figure, the gain of the amplifier is represented as A. The gain of the amplifier is the ratio of output voltage Vo to the input voltage Vi. The feedback network extracts a voltage Vf = β Vo from the output Vo of the amplifier. This voltage is added for positive feedback and subtracted for negative feedback, from the signal voltage Vs. So, for a positive feedback, Vi = Vs + Vf = Vs + β Vo The quantity β = Vf/Vo is called as feedback ratio or feedback fraction. The output Vo must be equal to the input voltage (Vs + βvo) multiplied by the gain A of the amplifier. Hence, (Vs+βVo)A=Vo Or AVs+AβVo=Vo Or AVs=Vo(1 Aβ) Therefore Vo A Vs 1 A Let Af be the overall gain (gain with the feedback) of the amplifier. This is defined as the ratio of output voltage Vo to the applied signal voltage Vs, i.e., outputvoltage Vo Af inputsignalvoltage Vs Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 47

51 Rrom the above two equations, we can understand that, the equation of gain of the feedback amplifier with positive feedback is given by A Af 1 A Where Aβ is the feedback factor or the loop gain. If Aβ = 1, Af =. Thus the gain becomes infinity, i.e., there is output without any input. In another words, the amplifier works as an Oscillator. The condition Aβ = 1 is called as Barkhausen Criterion of oscillations. This is a very important factor to be always kept in mind, in the concept of Oscillators RC-Phase shift Oscillators Principle of Phase-shift oscillators We know that the output voltage of an RC circuit for a sinewave input leads the input voltage. The phase angle by which it leads is determined by the value of RC components used in the circuit. The following circuit diagram shows a single section of an RC network. The output voltage V1 across the resistor R leads the input voltage applied input V1 by some phase angle ɸ o. If R were reduced to zero, V1 will lead the V1 by 90 o i.e., ɸ o = 90 o. However, adjusting R to zero would be impracticable, because it would lead to no voltage across R. Therefore, in practice, R is varied to such a value that makes V1 to lead V1 by 60 o. The following circuit diagram shows the three sections of the RC network. Each section produces a phase shift of 60 o. Consequently, a total phase shift of 180 o is produced, i.e., voltage V2 leads the voltage V1 by 180 o. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 48

52 Phase-shift Oscillator Circuit The oscillator circuit that produces a sine wave using a phase-shift network is called as a Phase-shift oscillator circuit. The constructional details and operation of a phase-shift oscillator circuit are as given below. Construction The phase-shift oscillator circuit consists of a single transistor amplifier section and a RC phase-shift network. The phase shift network in this circuit, consists of three RC sections. At the resonant frequency fo, the phase shift in each RC section is 60 o so that the total phase shift produced by RC network is 180 o. The following circuit diagram shows the arrangement of an RC phase-shift oscillator. The frequency of oscillations is given by Where Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 49

53 Operation The circuit when switched ON oscillates at the resonant frequency fo. The output Eo of the amplifier is fed back to RC feedback network. This network produces a phase shift of 180 o and a voltage Ei appears at its output. This voltage is applied to the transistor amplifier. The feedback applied will be m=ei/eo The feedback is in correct phase, whereas the transistor amplifier, which is in CE configuration, produces a 180 o phase shift. The phase shift produced by network and the transistor add to form a phase shift around the entire loop which is 360 o. Advantages The advantages of RC phase shift oscillator are as follows It does not require transformers or inductors. It can be used to produce very low frequencies. The circuit provides good frequency stability. Disadvantages The disadvantages of RC phase shift oscillator are as follows Starting the oscillations is difficult as the feedback is small. The output produced is small. Another type of popular audio frequency oscillator is the Wien bridge oscillator circuit. This is mostly used because of its important features. This circuit is free from the circuit fluctuations and the ambient temperature. The main advantage of this oscillator is that the frequency can be varied in the range of 10Hz to about 1MHz whereas in RC oscillators, the frequency is not varied. Wien bridge oscillator Construction The circuit construction of Wien bridge oscillator can be explained as below. It is a twostage amplifier with RC bridge circuit. The bridge circuit has the arms R1C1, R3, R2C2 and the tungsten lamp Lp. Resistance R3 and the lamp Lp are used to stabilize the amplitude of the output. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 50

54 The following circuit diagram shows the arrangement of a Wien bridge oscillator. The transistor T1 serves as an oscillator and an amplifier while the other transistor T2 serves as an inverter. The inverter operation provides a phase shift of 180 o. This circuit provides positive feedback through R1C1, C2R2 to the transistor T1 and negative feedback through the voltage divider to the input of transistor T2. The frequency of oscillations is determined by the series element R1C1 and parallel element R2C2 of the bridge. If R1 = R2 and C1 = C2 = C Then, Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 51

55 Now, we can simplify the above circuit as follows The oscillator consists of two stages of RC coupled amplifier and a feedback network. The voltage across the parallel combination of R and C is fed to the input of amplifier 1. The net phase shift through the two amplifiers is zero. The usual idea of connecting the output of amplifier 2 to amplifier 1 to provide signal regeneration for oscillator is not applicable here as the amplifier 1 will amplify signals over a wide range of frequencies and hence direct coupling would result in poor frequency stability. By adding Wien bridge feedback network, the oscillator becomes sensitive to a particular frequency and hence frequency stability is achieved. Operation When the circuit is switched ON, the bridge circuit produces oscillations of the frequency stated above. The two transistors produce a total phase shift of 360 o so that proper positive feedback is ensured. The negative feedback in the circuit ensures constant output. This is achieved by temperature sensitive tungsten lamp Lp. Its resistance increases with current. If the amplitude of the output increases, more current is produced and more negative feedback is achieved. Due to this, the output would return to the original value. Whereas, if the output tends to decrease, reverse action would take place. Advantages The advantages of Wien bridge oscillator are as follows The circuit provides good frequency stability. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 52

56 It provides constant output. The operation of circuit is quite easy. The overall gain is high because of two transistors. The frequency of oscillations can be changed easily. The amplitude stability of the output voltage can be maintained more accurately, by replacing R2 with a thermistor. Disadvantages The disadvantages of Wien bridge oscillator are as follows The circuit cannot generate very high frequencies. Two transistors and number of components are required for the circuit construction. LC Oscillators An oscillatory circuit produces electrical oscillations of a desired frequency. They are also known as tank circuits. A simple tank circuit comprises of an inductor L and a capacitor C both of which together determine the oscillatory frequency of the circuit. To understand the concept of oscillatory circuit, let us consider the following circuit. The capacitor in this circuit is already charged using a dc source. In this situation, the upper plate of the capacitor has excess of electrons whereas the lower plate has deficit of electrons. The capacitor holds some electrostatic energy and there is a voltage across the capacitor. When the switch S is closed, the capacitor discharges and the current flows through the inductor. Due to the inductive effect, the current builds up slowly towards a maximum value. Once the capacitor discharges completely, the magnetic field around the coil is maximum. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 53

57 Now, let us move on to the next stage. Once the capacitor is discharged completely, the magnetic field begins to collapse and produces a counter EMF according to Lenz s law. The capacitor is now charged with positive charge on the upper plate and negative charge on the lower plate. Once the capacitor is fully charged, it starts to discharge to build up a magnetic field around the coil, as shown in the following circuit diagram. This continuation of charging and discharging results in alternating motion of electrons or an oscillatory current. The interchange of energy between L and C produce continuous oscillations. In an ideal circuit, where there are no losses, the oscillations would continue indefinitely. In a practical tank circuit, there occur losses such as resistive and radiation losses in the coil and dielectric losses in the capacitor. These losses result in damped oscillations. Frequency of Oscillations The frequency of the oscillations produced by the tank circuit are determined by the components of the tank circuit, the L and the C. The actual frequency of oscillations is the resonant frequency(or natural frequency) of the tank circuit which is given by 1 fr= 2 LC Capacitance of the capacitor Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 54

58 The frequency of oscillation fo is inversely proportional to the square root of the capacitance of a capacitor. So, if the value of the capacitor used is large, the charge and discharge time periods will be large. Hence the frequency will be lower. Mathematically, the frequency, fo 1 C Self-Inductance of the coil The frequency of the oscillation fo is proportional to the square root of the self-inductance of the coil. If the value of the inductance is large, the opposition to change of current flow is greater and hence the time required to complete each cycle will be longer, which means time period will be longer and frequency will be lower. Mathematically, the frequency, fo 1 L ombining both the above equations, 1 fo LC 1 fo 2 LC The above equation, though indicates the output frequency, matches the natural frequency or resonance frequency of the tank circuit. An Oscillator circuit is a complete set of all the parts of circuit which helps to produce the oscillations. These oscillations should sustain and should be Undamped as just discussed before. Let us try to analyze a practical Oscillator circuit to have a better understanding on how an Oscillator circuit works. Practical Oscillator Circuit A Practical Oscillator circuit consists of a tank circuit, a transistor amplifier, and a feedback circuit. The following circuit diagram shows the arrangement of a practical oscillator. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 55

59 Let us now discuss the parts of this practical oscillator circuit. Tank Circuit The tank circuit consists of an inductance L connected in parallel with capacitor C. The values of these two components determine the frequency of the oscillator circuit and hence this is called as Frequency determining circuit. Transistor Amplifier The output of the tank circuit is connected to the amplifier circuit so that the oscillations produced by the tank circuit are amplified here. Hence the output of these oscillations are increased by the amplifier. Feedback Circuit The function of feedback circuit is to transfer a part of the output energy to LC circuit in proper phase. This feedback is positive in oscillators while negative in amplifiers. Frequency Stability of an Oscillator The frequency stability of an oscillator is a measure of its ability to maintain a constant frequency, over a long time interval. When operated over a longer period of time, the oscillator frequency may have a drift from the previously set value either by increasing or by decreasing. The change in oscillator frequency may arise due to the following factors Operating point of the active device such as BJT or FET used should lie in the linear region of the amplifier. Its deviation will affect the oscillator frequency. The temperature dependency of the performance of circuit components affect the oscillator frequency. The changes in d.c. supply voltage applied to the active device, shift the oscillator frequency. This can be avoided if a regulated power supply is used. A change in output load may cause a change in the Q-factor of the tank circuit, thereby causing a change in oscillator output frequency. The presence of inter element capacitances and stray capacitances affect the oscillator output frequency and thus frequency stability. Tuned circuit oscillators are the circuits that produce oscillations with the help of tuning circuits. The tuning circuits consists of an inductance L and a capacitor C. These are also known as LC oscillators, resonant circuit oscillators or tank circuit oscillators. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 56

60 The tuned circuit oscillators are used to produce an output with frequencies ranging from 1 MHz to 500 MHz Hence these are also known as R.F. Oscillators. A BJT or a FET is used as an amplifier with tuned circuit oscillators. With an amplifier and an LC tank circuit, we can feedback a signal with right amplitude and phase to maintain oscillations. Types of Tuned Circuit Oscillators Most of the oscillators used in radio transmitters and receivers are of LC oscillators type. Depending upon the way the feedback is used in the circuit, the LC oscillators are divided as the following types. Hartley Oscillator It uses inductive feedback. Colpitts Oscillator It uses capacitive feedback. Clapp Oscillator It uses capacitive feedback. Hartley Oscillator A very popular local oscillator circuit that is mostly used in radio receivers is the Hartley Oscillator circuit. The constructional details and operation of a Hartley oscillator are as discussed below. Construction In the circuit diagram of a Hartley oscillator shown below, the resistors R1, R2 and Re provide necessary bias condition for the circuit. The capacitor Ce provides a.c. ground thereby providing any signal degeneration. This also provides temperature stabilization. The capacitors Cc and Cb are employed to block d.c. and to provide an a.c. path. The radio frequency choke (R.F.C) offers very high impedance to high frequency currents which means it shorts for d.c. and opens for a.c. Hence it provides d.c. load for collector and keeps a.c. currents out of d.c. supply source Tank Circuit The frequency determining network is a parallel resonant circuit which consists of the inductors L1 and L2 along with a variable capacitor C. The junction of L1 and L2 are earthed. The coil L1 has its one end connected to base via Cc and the other to emitter via Ce. So, L2 is in the output circuit. Both the coils L1 and L2 are inductively coupled and together form an Auto-transformer. The following circuit diagram shows the arrangement of a Hartley oscillator. The tank circuit is shunt fed in this circuit. It can also be a series-fed. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 57

61 Operation When the collector supply is given, a transient current is produced in the oscillatory or tank circuit. The oscillatory current in the tank circuit produces a.c. voltage across L1. The auto-transformer made by the inductive coupling of L1 and L2 helps in determining the frequency and establishes the feedback. As the CE configured transistor provides 180 o phase shift, another 180 o phase shift is provided by the transformer, which makes 360 o phase shift between the input and output voltages. This makes the feedback positive which is essential for the condition of oscillations. When the loop gain βa of the amplifier is greater than one, oscillations are sustained in the circuit. Frequency The equation for frequency of Hartley oscillator is given as Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 58

62 Here, LT is the total cumulatively coupled inductance; L1 and L2represent inductances of 1 st and 2 nd coils; and M represents mutual inductance. Mutual inductance is calculated when two windings are considered. Advantages The advantages of Hartley oscillator are Instead of using a large transformer, a single coil can be used as an autotransformer. Frequency can be varied by employing either a variable capacitor or a variable inductor. Less number of components are sufficient. The amplitude of the output remains constant over a fixed frequency range. Disadvantages The disadvantages of Hartley oscillator are It cannot be a low frequency oscillator. Harmonic distortions are present. Applications The applications of Hartley oscillator are It is used to produce a sinewave of desired frequency. Mostly used as a local oscillator in radio receivers. It is also used as R.F. Oscillator. Colpitts oscillator A Colpitts oscillator looks just like the Hartley oscillator but the inductors and capacitors are replaced with each other in the tank circuit. The constructional details and operation of a colpitts oscillator are as discussed below. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 59

63 Construction Let us first take a look at the circuit diagram of a Colpitts oscillator. The resistors R1, R2 and Re provide necessary bias condition for the circuit. The capacitor Ce provides a.c. ground thereby providing any signal degeneration. This also provides temperature stabilization. The capacitors Cc and Cb are employed to block d.c. and to provide an a.c. path. The radio frequency choke (R.F.C) offers very high impedance to high frequency currents which means it shorts for d.c. and opens for a.c. Hence it provides d.c. load for collector and keeps a.c. currents out of d.c. supply source. Tank Circuit The frequency determining network is a parallel resonant circuit which consists of variable capacitors C1 and C2 along with an inductor L. The junction of C1 and C2 are earthed. The capacitor C1 has its one end connected to base via Cc and the other to emitter via Ce. the voltage developed across C1 provides the regenerative feedback required for the sustained oscillations. Operation When the collector supply is given, a transient current is produced in the oscillatory or tank circuit. The oscillatory current in the tank circuit produces a.c. voltage across C1 which are Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 60

64 applied to the base emitter junction and appear in the amplified form in the collector circuit and supply losses to the tank circuit. If terminal 1 is at positive potential with respect to terminal 3 at any instant, then terminal 2 will be at negative potential with respect to 3 at that instant because terminal 3 is grounded. Therefore, points 1 and 2 are out of phase by 180 o. As the CE configured transistor provides 180 o phase shift, it makes 360 o phase shift between the input and output voltages. Hence, feedback is properly phased to produce continuous Undamped oscillations. When the loop gain βa of the amplifier is greater than one, oscillations are sustained in the circuit. Frequency The equation for frequency of Colpitts oscillator is given as CT is the total capacitance of C1 and C2 connected in series. Advantages The advantages of Colpitts oscillator are as follows Colpitts oscillator can generate sinusoidal signals of very high frequencies. It can withstand high and low temperatures. The frequency stability is high. Frequency can be varied by using both the variable capacitors. Less number of components are sufficient. The amplitude of the output remains constant over a fixed frequency range. The Colpitts oscillator is designed to eliminate the disadvantages of Hartley oscillator and is known to have no specific disadvantages. Hence there are many applications of a colpitts oscillator. Applications Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 61

65 The applications of Colpitts oscillator are as follows Colpitts oscillator can be used as High frequency sinewave generator. This can be used as a temperature sensor with some associated circuitry. Mostly used as a local oscillator in radio receivers. It is also used as R.F. Oscillator. It is also used in Mobile applications. It has got many other commercial applications. Clapp Oscillator Another oscillator which is an advanced version of Colpitts oscillator is the Clapp Oscillator. This circuit is designed by making a few changes to the Colpitts oscillator. The circuit differs from the Colpitts oscillator only in one respect; it contains one additional capacitor (C3) connected in series with the inductor. The addition of capacitor (C3) improves the frequency stability and eliminates the effect of transistor parameters and stray capacitances. The following circuit diagram shows the arrangement of atransistor Clapp oscillator. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 62

66 The operation of Clapp oscillator circuit is in the same way as that of Colpitts oscillator. The frequency of oscillator is given by the relation, Where Usually, the value of C3 is much smaller than C1 and C2. As a result of this, C is approximately equal to C3. Therefore, the frequency of oscillation, It is understood that the Clapp oscillator is similar to the Colpitts oscillator, however they differ in the way the inductances and capacitances are arranged. The frequency stability though is good, can be variable in a Clapp oscillator. A Clapp oscillator is sometimes preferred over a Colpitts oscillator for constructing a variable frequency oscillator. The Clapp oscillators are used in receiver tuning circuits as a frequency oscillator. One of the important features of an oscillator is that the feedback energy applied should be in correct phase to the tank circuit. The oscillator circuits discussed so far has employed inductor (L) and capacitor (C) combination, in the tank circuit or frequency determining circuit. We have observed that the LC combination in oscillators provide 180 o phase shift and transistor in CE configuration provide 180 phase shift to make a total of 360 o phase shift so that it would make a zero difference in phase. Drawbacks of LC circuits Though they have few applications, the LC circuits have fewdrawbacks such as Frequency instability Waveform is poor Cannot be used for low frequencies Inductors are bulky and expensive Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 63

67 Whenever an oscillator is under continuous operation, itsfrequency stability gets affected. There occur changes in its frequency. The main factors that affect the frequency of an oscillator are Power supply variations Changes in temperature Changes in load or output resistance In RC and LC oscillators the values of resistance, capacitance and inductance vary with temperature and hence the frequency gets affected. In order to avoid this problem, the piezo electric crystals are being used in oscillators. Crystal Oscillators The use of piezo electric crystals in parallel resonant circuits provide high frequency stability in oscillators. Such oscillators are called as Crystal Oscillators. Crystal Oscillators The principle of crystal oscillators depends upon the Piezo electric effect. The natural shape of a crystal is hexagonal. When a crystal wafer is cur perpendicular to X-axis, it is called as X-cut and when it is cut along Y-axis, it is called as Y-cut. The crystal used in crystal oscillator exhibits a property called as Piezo electric property. So, let us have an idea on piezo electric effect. Piezo Electric Effect The crystal exhibits the property that when a mechanical stress is applied across one of the faces of the crystal, a potential difference is developed across the opposite faces of the crystal. Conversely, when a potential difference is applied across one of the faces, a mechanical stress is produced along the other faces. This is known as Piezo electric effect. Certain crystalline materials like Rochelle salt, quartz and tourmaline exhibit piezo electric effect and such materials are called as Piezo electric crystals. Quartz is the most commonly used piezo electric crystal because it is inexpensive and readily available in nature. When a piezo electric crystal is subjected to a proper alternating potential, it vibrates mechanically. The amplitude of mechanical vibrations becomes maximum when the frequency of alternating voltage is equal to the natural frequency of the crystal. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 64

68 Working of a Quartz Crystal In order to make a crystal work in an electronic circuit, the crystal is placed between two metal plates in the form of a capacitor.quartz is the mostly used type of crystal because of its availability and strong nature while being inexpensive. The ac voltage is applied in parallel to the crystal. The circuit arrangement of a Quartz Crystal will be as shown below If an AC voltage is applied, the crystal starts vibrating at the frequency of the applied voltage. However, if the frequency of the applied voltage is made equal to the natural frequency of the crystal, resonance takes place and crystal vibrations reach a maximum value. This natural frequency is almost constant. Equivalent circuit of a Crystal If we try to represent the crystal with an equivalent electric circuit, we have to consider two cases, i.e., when it vibrates and when it doesn t. The figures below represent the symbol and electrical equivalent circuit of a crystal respectively. The above equivalent circuit consists of a series R-L-C circuit in parallel with a capacitance Cm. When the crystal mounted across the AC source is not vibrating, it is equivalent to the capacitance Cm. When the crystal vibrates, it acts like a tuned R-L-C circuit. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 65

69 Frequency response The frequency response of a crystal is as shown below. The graph shows the reactance (XL or XC) versus frequency (f). It is evident that the crystal has two closely spaced resonant frequencies. The first one is the series resonant frequency (fs), which occurs when reactance of the inductance (L) is equal to the reactance of the capacitance C. In that case, the impedance of the equivalent circuit is equal to the resistance R and the frequency of oscillation is given by the relation, The second one is the parallel resonant frequency (fp), which occurs when the reactance of R-L-C branch is equal to the reactance of capacitor Cm. At this frequency, the crystal offers a very high impedance to the external circuit and the frequency of oscillation is given by the relation. Where The value of Cm is usually very large as compared to C. Therefore, the value of CT is approximately equal to C and hence the series resonant frequency is approximately equal to the parallel resonant frequency (i.e., fs = fp). Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 66

70 Crystal Oscillator Circuit pierce crystal oscillator A crystal oscillator circuit can be constructed in a number of ways like a Crystal controlled tuned collector oscillator, a Colpitts crystal oscillator, a Clap crystal oscillator etc. But the transistor pierce crystal oscillator is the most commonly used one. This is the circuit which is normally referred as a crystal oscillator circuit. The following circuit diagram shows the arrangement of a transistor pierce crystal oscillator. In this circuit, the crystal is connected as a series element in the feedback path from collector to the base. The resistors R1, R2 and RE provide a voltage-divider stabilized d.c. bias circuit. The capacitor CE provides a.c. bypass of the emitter resistor and RFC (radio frequency choke) coil provides for d.c. bias while decoupling any a.c. signal on the power lines from affecting the output signal. The coupling capacitor C has negligible impedance at the circuit operating frequency. But it blocks any d.c. between collector and base. The circuit frequency of oscillation is set by the series resonant frequency of the crystal and its value is given by the relation, It may be noted that the changes in supply voltage, transistor device parameters etc. have no effect on the circuit operating frequency, which is held stabilized by the crystal. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 67

71 Advantages The advantages of crystal oscillator are as follows They have a high order of frequency stability. The quality factor (Q) of the crystal is very high. Disadvantages The disadvantages of crystal oscillator are as follows They are fragile and can be used in low power circuits. The frequency of oscillations cannot be changed appreciably. Frequency Stability of an Oscillator An Oscillator is expected to maintain its frequency for a longer duration without any variations, so as to have a smoother clear sinewave output for the circuit operation. Hence the term frequency stability really matters a lot, when it comes to oscillators, whether sinusoidal or non-sinusoidal. The frequency stability of an oscillator is defined as the ability of the oscillator to maintain the required frequency constant over a long time interval as possible. Let us try to discuss the factors that affect this frequency stability. Change in operating point We have already come across the transistor parameters and learnt how important an operating point is. The stability of this operating point for the transistor being used in the circuit for amplification (BJT or FET), is of higher consideration. The operating of the active device used is adjusted to be in the linear portion of its characteristics. This point is shifted due to temperature variations and hence the stability is affected. Variation in temperature The tank circuit in the oscillator circuit, contains various frequency determining components such as resistors, capacitors and inductors. All of their parameters are temperature dependent. Due to the change in temperature, their values get affected. This brings the change in frequency of the oscillator circuit. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 68

72 Due to power supply The variations in the supplied power will also affect the frequency. The power supply variations lead to the variations in Vcc. This will affect the frequency of the oscillations produced. In order to avoid this, the regulated power supply system is implemented. This is in short called as RPS. Change in output load The variations in output resistance or output load also affects the frequency of the oscillator. When a load is connected, the effective resistance of the tank circuit is changed. As a result, the Q-factor of LC tuned circuit is changed. This results a change in output frequency of oscillator. Changes in inter-element capacitances Inter-element capacitances are the capacitances that develop in PN junction materials such as diodes and transistors. These are developed due to the charge present in them during their operation. The inter element capacitors undergo change due to various reasons as temperature, voltage etc. This problem can be solved by connecting swamping capacitor across offending inter-element capacitor. Value of Q The value of Q (Quality factor) must be high in oscillators. The value of Q in tuned oscillators determine the selectivity. As this Q is directly proportional to the frequency stability of a tuned circuit, the value of Q should be maintained high. Frequency stability can be mathematically represented as, Sw=dθ/dw Where dθ is the phase shift introduced for a small frequency change in nominal frequency fr. The circuit giving the larger value of (dθ/dw) has more stable oscillatory frequency. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 69

73 UNIT-IV Power Amplifiers In practice, any amplifier consists of few stages of amplification. If we consider audio amplification, it has several stages of amplification, depending upon our requirement. Power Amplifier After the audio signal is converted into electrical signal, it has several voltage amplifications done, after which the power amplification of the amplified signal is done just before the loud speaker stage. This is clearly shown in the below figure. While the voltage amplifier raises the voltage level of the signal, the power amplifier raises the power level of the signal. Besides raising the power level, it can also be said that a power amplifier is a device which converts DC power to AC power and whose action is controlled by the input signal. The DC power is distributed according to the relation, DC power input = AC power output + losses Power Transistor For such Power amplification, a normal transistor would not do. A transistor that is manufactured to suit the purpose of power amplification is called as a Power transistor. A Power transistor differs from the other transistors, in the following factors. It is larger in size, in order to handle large powers. The collector region of the transistor is made large and a heat sink is placed at the collector-base junction in order to minimize heat generated. The emitter and base regions of a power transistor are heavily doped. Due to the low input resistance, it requires low input power. Hence there is a lot of difference in voltage amplification and power amplification. So, let us now try to get into the details to understand the differences between a voltage amplifier and a power amplifier. Difference between Voltage and Power Amplifiers:Let us try to differentiate between voltage and power amplifier. Voltage Amplifier The function of a voltage amplifier is to raise the voltage level of the signal. A voltage amplifier is designed to achieve maximum voltage amplification. The voltage gain of an amplifier is given by Av=β(Rc/Rin) The characteristics of a voltage amplifier are as follows The base of the transistor should be thin and hence the value of β should be greater than 100. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 70

74 The resistance of the input resistor Rin should be low when compared to collector load RC. The collector load RC should be relatively high. To permit high collector load, the voltage amplifiers are always operated at low collector current. The voltage amplifiers are used for small signal voltages. Power Amplifier The function of a power amplifier is to raise the power level of input signal. It is required to deliver a large amount of power and has to handle large current. The characteristics of a power amplifier are as follows The base of transistor is made thicken to handle large currents. The value of β being (β > 100) high. The size of the transistor is made larger, in order to dissipate more heat, which is produced during transistor operation. Transformer coupling is used for impedance matching. Collector resistance is made low. The comparison between voltage and power amplifiers is given below in a tabular form. S.No Particular Voltage Amplifier Power Amplifier 1 β High (>100) Low (5 to 20) 2 RC High (4-10 KΩ) Low (5 to 20 Ω) 3 Coupling Usually R-C coupling Invariably transformer coupling 4 Input voltage Low (a few m V) High (2-4 V) 5 Collector current Low ( 1 ma) High (> 100 ma) 6 Power output Low High 7 Output impendence High ( 12 K Ω) Low (200 Ω The Power amplifiers amplify the power level of the signal. This amplification is done in the last stage in audio applications. The applications related to radio frequencies employ radio power amplifiers. But the operating point of a transistor plays a very important role in determining the efficiency of the amplifier. The main classification is done based on this mode of operation. The classification is done based on their frequencies and also based on their mode of operation. Classification Based on Frequencies Power amplifiers are divided into two categories, based on the frequencies they handle. They are as follows. Audio Power Amplifiers The audio power amplifiers raise the power level of signals that have audio frequency range (20 Hz to 20 KHz). They are also known as Small signal power amplifiers. Radio Power Amplifiers Radio Power Amplifiers or tuned power amplifiers raise the power level of signals that have radio frequency range (3 KHz to 300 GHz). They are also known as large signal power amplifiers. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 71

75 Classification Based on Mode of Operation On the basis of the mode of operation, i.e., the portion of the input cycle during which collector current flows, the power amplifiers may be classified as follows. Class A Power amplifier When the collector current flows at all times during the full cycle of signal, the power amplifier is known as class A power amplifier. Class B Power amplifier When the collector current flows only during the positive half cycle of the input signal, the power amplifier is known as class B power amplifier. Class C Power amplifier When the collector current flows for less than half cycle of the input signal, the power amplifier is known as class C power amplifier. There forms another amplifier called Class AB amplifier, if we combine the class A and class B amplifiers so as to utilize the advantages of both. Before going into the details of these amplifiers, let us have a look at the important terms that have to be considered to determine the efficiency of an amplifier. Terms Considering Performance The primary objective of a power amplifier is to obtain maximum output power. In order to achieve this, the important factors to be considered are collector efficiency, power dissipation capability and distortion. Let us go through them in detail. Collector Efficiency This explains how well an amplifier converts DC power to AC power. When the DC supply is given by the battery but no AC signal input is given, the collector output at such a condition is observed as collector efficiency. The collector efficiency is defined as η=average a.c poweroutput / average d.c powerinputtotransisto The main aim of a power amplifier is to obtain maximum collector efficiency. Hence the higher the value of collector efficiency, the efficient the amplifier will be. Power Dissipation Capacity Every transistor gets heated up during its operation. As a power transistor handles large currents, it gets more heated up. This heat increases the temperature of the transistor, which alters the operating point of the transistor. So, in order to maintain the operating point stability, the temperature of the transistor has to be kept in permissible limits. For this, the heat produced has to be dissipated. Such a capacity is called as Power dissipation capability. Power dissipation capability can be defined as the ability of a power transistor to dissipate the heat developed in it. Metal cases called heat sinks are used in order to dissipate the heat produced in power transistors. Distortion A transistor is a non-linear device. When compared with the input, there occur few variations in the output. In voltage amplifiers, this problem is not pre-dominant as small Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 72

76 currents are used. But in power amplifiers, as large currents are in use, the problem of distortion certainly arises. Distortion is defined as the change of output wave shape from the input wave shape of the amplifier. An amplifier that has lesser distortion, produces a better output and hence considered efficient. We have already come across the details of transistor biasing, which is very important for the operation of a transistor as an amplifier. Hence to achieve faithful amplification, the biasing of the transistor has to be done such that the amplifier operates over the linear region. A Class A power amplifier is one in which the output current flows for the entire cycle of the AC input supply. Hence the complete signal present at the input is amplified at the output. The following figure shows the circuit diagram for Class A Power amplifier. From the above figure, it can be observed that the transformer is present at the collector as a load. The use of transformer permits the impedance matching, resulting in the transference of maximum power to the load e.g. loud speaker. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 73

77 The operating point of this amplifier is present in the linear region. It is so selected that the current flows for the entire ac input cycle. The below figure explains the selection of operating point. The output characteristics with operating point Q is shown in the figure above. Here (Ic)Q and (Vce)Q represent no signal collector current and voltage between collector and emitter respectively. When signal is applied, the Q-point shifts to Q1 and Q2. The output current increases to (Ic)max and decreases to (Ic)min. Similarly, the collector-emitter voltage increases to (Vce)max and decreases to (Vce)min. D.C. Power drawn from collector battery Vcc is given by Pin=voltage current=vcc(ic)q This power is used in the following two parts Power dissipated in the collector load as heat is given by PRC=(current) 2 resistance=(ic) 2 QRC Power given to transistor is given by Ptr=Pin PRC=VCC (IC)2QRC When signal is applied, the power given to transistor is used in the following two parts A.C. Power developed across load resistors RC which constitutes the a.c. power output. (PO)ac=I 2 RC=V 2 / RC=(Vm/ 2 ) /RC=V2m/2RC Where I is the R.M.S. value of a.c. output current through load, V is the R.M.S. value of a.c. voltage, and Vm is the maximum value of V. The D.C. power dissipated by the transistor (collector region) in the form of heat, i.e., (PC)dc We have represented the whole power flow in the following diagram. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 74

78 This class A power amplifier can amplify small signals with least distortion and the output will be an exact replica of the input with increased strength. Let us now try to draw some expressions to represent efficiencies. Advantages of Class A Amplifiers The advantages of Class A power amplifier are as follows The current flows for complete input cycle It can amplify small signals The output is same as input No distortion is present Disadvantages of Class A Amplifiers The advantages of Class A power amplifier are as follows Low power output Low collector efficiency The class A power amplifier as discussed in the previous chapter, is the circuit in which the output current flows for the entire cycle of the AC input supply. We also have learnt about the disadvantages it has such as low output power and efficiency. In order to Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 75

79 minimize those effects, the transformer coupled class A power amplifier has been introduced. The construction of class A power amplifier can be understood with the help of below figure. This is similar to the normal amplifier circuit but connected with a transformer in the collector load. Here R1 and R2 provide potential divider arrangement. The resistor Re provides stabilization, Ce is the bypass capacitor and Re to prevent a.c. voltage. The transformer used here is a step-down transformer.the high impedance primary of the transformer is connected to the high impedance collector circuit. The low impedance secondary is connected to the load (generally loud speaker). Transformer Action: The transformer used in the collector circuit is for impedance matching. RL is the load connected in the secondary of a transformer. RL is the reflected load in the primary of the transformer. The number of turns in the primary are n1 and the secondary are n2. Let V1 and V2 be the primary and secondary voltages and I1 and I2 be the primary and secondary currents respectively. The below figure shows the transformer clearly. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 76

80 A power amplifier may be matched by taking proper turn ratio in step down transformer. Circuit Operation If the peak value of the collector current due to signal is equal to zero signal collector current, then the maximum a.c. power output is obtained. So, in order to achieve complete amplification, the operating point should lie at the center of the load line. The operating point obviously varies when the signal is applied. The collector voltage varies in opposite phase to the collector current. The variation of collector voltage appears across the primary of the transformer. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 77

81 Circuit Analysis The power loss in the primary is assumed to be negligible, as its resistance is very small. The input power under dc condition will be The efficiency of a class A power amplifier is nearly than 30% whereas it has got improved to 50% by using the transformer coupled class A power amplifier. Advantages The advantages of transformer coupled class A power amplifier are as follows. No loss of signal power in the base or collector resistors. Excellent impedance matching is achieved. Gain is high. DC isolation is provided. Disadvantages The disadvantages of transformer coupled class A power amplifier are as follows. Low frequency signals are less amplified comparatively. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 78

82 Hum noise is introduced by transformers. Transformers are bulky and costly. Poor frequency response. Applications The applications of transformer coupled class A power amplifier are as follows. This circuit is where impedance matching is the main criterion. These are used as driver amplifiers and sometimes as output amplifiers. When the collector current flows only during the positive half cycle of the input signal, the power amplifier is known as class B power amplifier. Class B Operation The biasing of the transistor in class B operation is in such a way that at zero signal condition, there will be no collector current. The operating point is selected to be at collector cut off voltage. So, when the signal is applied, only the positive half cycle is amplified at the output. The figure below shows the input and output waveforms during class B operation. When the signal is applied, the circuit is forward biased for the positive half cycle of the input and hence the collector current flows. But during the negative half cycle of the input, the circuit is reverse biased and the collector current will be absent. Hence only the positive half cycle is amplified at the output. As the negative half cycle is completely absent, the signal distortion will be high. Also, when the applied signal increases, the power dissipation will be more. But when compared to class A power amplifier, the output efficiency is increased.well, in order to minimize the disadvantages and achieve low distortion, high efficiency and high output power, the push-pull configuration is used in this class B amplifier. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 79

83 Class B Push-Pull Amplifier Though the efficiency of class B power amplifier is higher than class A, as only one half cycle of the input is used, the distortion is high. Also, the input power is not completely utilized. In order to compensate these problems, the push-pull configuration is introduced in class B amplifier. Construction: The circuit of a push-pull class B power amplifier consists of two identical transistors T1 and T2 whose bases are connected to the secondary of the center-tapped input transformer Tr1. The emitters are shorted and the collectors are given the VCC supply through the primary of the output transformer Tr2. The circuit arrangement of class B push-pull amplifier, is same as that of class A push-pull amplifier except that the transistors are biased at cut off, instead of using the biasing resistors. The figure below gives the detailing of the construction of a push-pull class B power amplifier. The circuit operation of class B push pull amplifier is detailed below. Operation The circuit of class B push-pull amplifier shown in the above figure clears that both the transformers are center-tapped. When no signal is applied at the input, the transistors T1 and T2 are in cut off condition and hence no collector currents flow. As no current is drawn from VCC, no power is wasted. When input signal is given, it is applied to the input transformer Tr1 which splits the signal into two signals that are 180 o out of phase with each other. These two signals are given to the two identical transistors T1 and T2. For the positive half cycle, the base of the transistor T1 becomes positive and collector current flows. At the same time, the transistor T2 has negative half cycle, which throws the transistor T2 into cutoff condition and hence no collector current flows. The waveform is produced as shown in the following figure. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 80

84 For the next half cycle, the transistor T1 gets into cut off condition and the transistor T2 gets into conduction, to contribute the output. Hence for both the cycles, each transistor conducts alternately. The output transformer Tr3 serves to join the two currents producing an almost undistorted output waveform. Power Efficiency of Class B Push-Pull Amplifier The current in each transistor is the average value of half sine loop. For half sine loop, Idc is given by Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 81

85 The collector efficiency would be the same. Hence the class B push-pull amplifier improves the efficiency than the class A push-pull amplifier. Complementary Symmetry Push-Pull Class B Amplifier The push pull amplifier which was just discussed improves efficiency but the usage of center-tapped transformers makes the circuit bulky, heavy and costly. To make the circuit simple and to improve the efficiency, the transistors used can be complemented, as shown in the following circuit diagram. The above circuit employs a NPN transistor and a PNP transistor connected in push pull configuration. When the input signal is applied, during the positive half cycle of the input signal, the NPN transistor conducts and the PNP transistor cuts off. During the negative half cycle, the NPN transistor cuts off and the PNP transistor conducts. In this way, the NPN transistor amplifies during positive half cycle of the input, while PNP transistor amplifies during negative half cycle of the input. As the transistors are both complement to each other, yet act symmetrically while being connected in push pull configuration of class B, this circuit is termed as Complementary symmetry push pull class B amplifier. Advantages The advantages of Complementary symmetry push pull class B amplifier are as follows. As there is no need of center tapped transformers, the weight and cost are reduced. Equal and opposite input signal voltages are not required. Disadvantages The disadvantages of Complementary symmetry push pull class B amplifier are as follows. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 82

86 It is difficult to get a pair of transistors (NPN and PNP) that have similar characteristics. We require both positive and negative supply voltages. The class A and class B amplifier so far discussed has got few limitations. Let us now try to combine these two to get a new circuit which would have all the advantages of both class A and class B amplifier without their inefficiencies. Before that, let us also go through another important problem, called as Cross over distortion, the output of class B encounters with. Cross-over Distortion: In the push-pull configuration, the two identical transistors get into conduction, one after the other and the output produced will be the combination of both. When the signal changes or crosses over from one transistor to the other at the zero voltage point, it produces an amount of distortion to the output wave shape. For a transistor in order to conduct, the base emitter junction should cross 0.7v, the cut off voltage. The time taken for a transistor to get ON from OFF or to get OFF from ON state is called the transition period. At the zero voltage point, the transition period of switching over the transistors from one to the other, has its effect which leads to the instances where both the transistors are OFF at a time. Such instances can be called as Flat spot or Dead band on the output wave shape. The above figure clearly shows the cross over distortion which is prominent in the output waveform. This is the main disadvantage. This cross over distortion effect also reduces the overall peak to peak value of the output waveform which in turn reduces the maximum power output. This can be more clearly understood through the non-linear characteristic of the waveform as shown below. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 83

87 It is understood that this cross-over distortion is less pronounced for large input signals, where as it causes severe disturbance for small input signals. This cross over distortion can be eliminated if the conduction of the amplifier is more than one half cycle, so that both the transistors won t be OFF at the same time. This idea leads to the invention of class AB amplifier, which is the combination of both class A and class B amplifiers, as discussed below. Class AB Power Amplifier As the name implies, class AB is a combination of class A and class B type of amplifiers. As class A has the problem of low efficiency and class B has distortion problem, this class AB is emerged to eliminate these two problems, by utilizing the advantages of both the classes. The cross over distortion is the problem that occurs when both the transistors are OFF at the same instant, during the transition period. In order to eliminate this, the condition has to be chosen for more than one half cycle. Hence, the other transistor gets into conduction, before the operating transistor switches to cut off state. This is achieved only by using class AB configuration, as shown in the following circuit diagram. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 84

88 Therefore, in class AB amplifier design, each of the push-pull transistors is conducting for slightly more than the half cycle of conduction in class B, but much less than the full cycle of conduction of class A. The conduction angle of class AB amplifier is somewhere between 180 o to 360 o depending upon the operating point selected. This is understood with the help of below figure. The small bias voltage given using diodes D1 and D2, as shown in the above figure, helps the operating point to be above the cutoff point. Hence the output waveform of class AB results as seen in the above figure. The crossover distortion created by class B is overcome by this class AB, as well the inefficiencies of class A and B don t affect the circuit. So, the class AB is a good compromise between class A and class B in terms of efficiency and linearity having the efficiency reaching about 50% to 60%. The class A, B and AB amplifiers are called as linear amplifiers because the output signal amplitude and phase are linearly related to the input signal amplitude and phase. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 85

89 Class C Power Amplifier When the collector current flows for less than half cycle of the input signal, the power amplifier is known as class C power amplifier. The efficiency of class C amplifier is high while linearity is poor. The conduction angle for class C is less than 180 o. It is generally around 90 o, which means the transistor remains idle for more than half of the input signal. So, the output current will be delivered for less time compared to the application of input signal. The following figure shows the operating point and output of a class C amplifier. This kind of biasing gives a much improved efficiency of around 80% to the amplifier, but introduces heavy distortion in the output signal. Using the class C amplifier, the pulses produced at its output can be converted to complete sine wave of a particular frequency by using LC circuits in its collector circuit. The types of amplifiers that we have discussed so far cannot work effectively at radio frequencies, even though they are good at audio frequencies. Also, the gain of these amplifiers is such that it will not vary according to the frequency of the signal, over a wide range. This allows the amplification of the signal equally well over a range of frequencies and does not permit the selection of particular desired frequency while rejecting the other frequencies. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 86

90 UNIT-V TUNED AMPLIFIER Tuned amplifiers are the amplifiers that are employed for the purpose of tuning. Tuning means selecting. Among a set of frequencies available, if there occurs a need to select a particular frequency, while rejecting all other frequencies, such a process is called Selection. This selection is done by using a circuit called as Tuned circuit. When an amplifier circuit has its load replaced by a tuned circuit, such an amplifier can be called as a Tuned amplifier circuit. The basic tuned amplifier circuit looks as shown below. The tuner circuit is nothing but a LC circuit which is also called as resonant or tank circuit. It selects the frequency. A tuned circuit is capable of amplifying a signal over a narrow band of frequencies that are centered at resonant frequency. When the reactance of the inductor balances the reactance of the capacitor, in the tuned circuit at some frequency, such a frequency can be called as resonant frequency. It is denoted by fr. The formula for resonance is Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 87

91 Types of Tuned Circuits A tuned circuit can be Series tuned circuit (Series resonant circuit) or Parallel tuned circuit (parallel resonant circuit) according to the type of its connection to the main circuit. Series Tuned Circuit The inductor and capacitor connected in series make a series tuned circuit, as shown in the following circuit diagram. At resonant frequency, a series resonant circuit offers low impedance which allows high current through it. A series resonant circuit offers increasingly high impedance to the frequencies far from the resonant frequency. Parallel Tuned Circuit The inductor and capacitor connected in parallel make a parallel tuned circuit, as shown in the below figure. At resonant frequency, a parallel resonant circuit offers high impedance which does not allow high current through it. A parallel resonant circuit offers increasingly low impedance to the frequencies far from the resonant frequency. Characteristics of a Parallel Tuned Circuit The frequency at which parallel resonance occurs (i.e. reactive component of circuit current becomes zero) is called the resonant frequency fr. The main characteristics of a tuned circuit are as follows. Impedance The ratio of supply voltage to the line current is the impedance of the tuned circuit. Impedance offered by LC circuit is given by Supply voltage / Lineequation=V / I At resonance, the line current increases while the impedance decreases. The below figure represents the impedance curve of a parallel resonance circuit. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 88

92 Impedance of the circuit decreases for the values above and below the resonant frequency fr. Hence the selection of a particular frequency and rejection of other frequencies is possible. To obtain an equation for the circuit impedance, let us consider Line Current I=ILcosϕ V/Zr=V/ZL R/ZL 1/Zr=R/Z 2 L 1/Zr =CR/L Since, Z2L=L/C Therefore, circuit impedance Zr is obtained as ZR=L/CR Thus at parallel resonance, the circuit impedance is equal to L/CR. Circuit Current At parallel resonance, the circuit or line current I is given by the applied voltage divided by the circuit impedance Zr i.e., Line Current I=VZr Where Zr=L/CR Because Zr is very high, the line current I will be very small. Quality Factor For a parallel resonance circuit, the sharpness of the resonance curve determines the selectivity. The smaller the resistance of the coil, the sharper the resonant curve will be. Hence the inductive reactance and resistance of the coil determine the quality of the tuned circuit. The ratio of inductive reactance of the coil at resonance to its resistance is known as Quality factor. It is denoted by Q. Q=XL/R=2πfrLR The higher the value of Q, the sharper the resonance curve and the better the selectivity will be. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 89

93 Advantages of Tuned Amplifiers The following are the advantages of tuned amplifiers. The usage of reactive components like L and C, minimizes the power loss, which makes the tuned amplifiers efficient. The selectivity and amplification of desired frequency is high, by providing higher impedance at resonant frequency. A smaller collector supply VCC would do, because of its little resistance in parallel tuned circuit. It is important to remember that these advantages are not applicable when there is a high resistive collector load. Frequency Response of Tuned Amplifier For an amplifier to be efficient, its gain should be high. This voltage gain depends upon β, input impedance and collector load. The collector load in a tuned amplifier is a tuned circuit. The voltage gain of such an amplifier is given by Voltage gain = Βzc/Zin Where ZC = effective collector load and Zin = input impedance of the amplifier. The value of ZC depends upon the frequency of the tuned amplifier. As ZC is maximum at resonant frequency, the gain of the amplifier is maximum at this resonant frequency. Bandwidth The range of frequencies at which the voltage gain of the tuned amplifier falls to 70.7% of the maximum gain is called its Bandwidth. The range of frequencies between f1 and f2 is called as bandwidth of the tuned amplifier. The bandwidth of a tuned amplifier depends upon the Q of the LC circuit i.e., upon the sharpness of the frequency response. The value of Q and the bandwidth are inversely proportional. The figure below details the bandwidth and frequency response of the tuned amplifier. Relation between Q and Bandwidth The quality factor Q of the bandwidth is defined as the ratio of resonant frequency to bandwidth, i.e., Q=fr / BW Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 90

94 In general, a practical circuit has its Q value greater than 10. Under this condition, the resonant frequency at parallel resonance is given by fr=1/ 2πLC There are two main types of tuned amplifiers. They are Single tuned amplifier Double tuned amplifier Single Tuned Amplifier An amplifier circuit with a single tuner section being at the collector of the amplifier circuit is called as Single tuner amplifier circuit. Construction A simple transistor amplifier circuit consisting of a parallel tuned circuit in its collector load, makes a single tuned amplifier circuit. The values of capacitance and inductance of the tuned circuit are selected such that its resonant frequency is equal to the frequency to be amplified. The following circuit diagram shows a single tuned amplifier circuit. The output can be obtained from the coupling capacitor CC as shown above or from a secondary winding placed at L. Operation The high frequency signal that has to be amplified is applied at the input of the amplifier. The resonant frequency of the parallel tuned circuit is made equal to the frequency of the signal applied by altering the capacitance value of the capacitor C, in the tuned circuit.at this stage, the tuned circuit offers high impedance to the signal frequency, which helps to offer high output across the tuned circuit. As high impedance is offered only for the tuned frequency, all the other frequencies which get lower impedance are rejected Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 91

95 by the tuned circuit. Hence the tuned amplifier selects and amplifies the desired frequency signal. Frequency Response The parallel resonance occurs at resonant frequency fr when the circuit has a high Q. the resonant frequency fr is given by fr=1/ 2πLC The following graph shows the frequency response of a single tuned amplifier circuit. At resonant frequency fr the impedance of parallel tuned circuit is very high and is purely resistive. The voltage across RL is therefore maximum, when the circuit is tuned to resonant frequency. Hence the voltage gain is maximum at resonant frequency and drops off above and below it. The higher the Q, the narrower will the curve be. Double Tuned Amplifier An amplifier circuit with a double tuner section being at the collector of the amplifier circuit is called as Double tuner amplifier circuit. Construction The construction of double tuned amplifier is understood by having a look at the following figure. This circuit consists of two tuned circuits L1C1 and L2C2 in the collector section of the amplifier. The signal at the output of the tuned circuit L1C1 is coupled to the other tuned circuit L2C2 through mutual coupling method. The remaining circuit details are same as in the single tuned amplifier circuit, as shown in the following circuit diagram. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 92

96 Operation The high frequency signal which has to be amplified is given to the input of the amplifier. The tuning circuit L1C1 is tuned to the input signal frequency. At this condition, the tuned circuit offers high reactance to the signal frequency. Consequently, large output appears at the output of the tuned circuit L1C1 which is then coupled to the other tuned circuit L2C2 through mutual induction. These double tuned circuits are extensively used for coupling various circuits of radio and television receivers. Frequency Response of Double Tuned Amplifier The double tuned amplifier has the special feature of coupling which is important in determining the frequency response of the amplifier. The amount of mutual inductance between the two tuned circuits states the degree of coupling, which determines the frequency response of the circuit. In order to have an idea on the mutual inductance property, let us go through the basic principle. Mutual Inductance As the current carrying coil produces some magnetic field around it, if another coil is brought near this coil, such that it is in the magnetic flux region of the primary, then the varying magnetic flux induces an EMF in the second coil. If this first coil is called as Primary coil, the second one can be called as a Secondary coil. When the EMF is induced in the secondary coil due to the varying magnetic field of the primary coil, then such phenomenon is called as the. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 93

97 Mutual Inductance. The figure below gives an idea about this. The current is in the figure indicate the source current while iind indicates the induced current. The flux represents the magnetic flux created around the coil. This spreads to the secondary coil also. With the application of voltage, the current is flows and flux gets created. When the current is varies the flux gets varied, producing iind in the secondary coil, due to the Mutual inductance property. Coupling Under the concept of mutual inductance coupling will be as shown in the figure below. When the coils are spaced apart, the flux linkages of primary coil L1 will not link the secondary coil L2. At this condition, the coils are said to have Loose coupling. The resistance reflected from the secondary coil at this condition is small and the resonance curve will be sharp and the circuit Q is high as shown in the figure below. Malla Reddy College of Engineering and Technology(MRCET) Department of ECE Page 94