SN75176A DIFFERENTIAL BUS TRANSCEIVER
|
|
- Amelia Neal
- 6 years ago
- Views:
Transcription
1 SN7576A Bidirectional Transceiver Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-4-B and ITU Recommendation V. Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments -State Driver and Receiver s Individual Driver and Receiver Enables Wide Positive and Negative Input/ Bus Voltage Ranges Driver Capability...±6 ma Max Thermal-Shutdown Protection Driver Positive- and Negative-Current Limiting Receiver Input Impedance... kω Min Receiver Input Sensitivity...± mv Receiver Input Hysteresis...5 mv Typ Operates From Single 5-V Supply Low Power Requirements R RE DE D SLLSA JUNE 984 REVISED MAY 995 D OR P PACKAGE (TOP VIEW) V CC B A GND description The SN7576A differential bus transceiver is a monolithic integrated circuit designed for bidirectional data communication on multipoint bus-transmission lines. It is designed for balanced transmission lines and meets ANSI Standard EIA/TIA-4-B and ITU Recommendation V.. The SN7576A combines a -state differential line driver and a differential input line receiver, both of which operate from a single 5-V power supply. The driver and receiver have active-high and active-low enables, respectively, that can be externally connected together to function as a direction control. The driver differential outputs and the receiver differential inputs are connected internally to form differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus whenever the driver is disabled or V CC =. These ports feature wide positive and negative common-mode voltage ranges making the device suitable for party-line applications. The driver is designed to handle loads up to 6 ma of sink or source current. The driver features positive- and negative-current limiting and thermal shutdown for protection from line fault conditions. Thermal shutdown is designed to occur at a junction temperature of approximately 5 C. The receiver features a minimum input impedance of kω, an input sensitivity of ± mv, and a typical input hysteresis of 5 mv. The SN7576A can be used in transmission-line applications employing the SN757 and SN7574 quadruple differential line drivers and SN757 and SN7575 quadruple differential line receivers. The SN7576A is characterized for operation from C to 7 C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright 995, Texas Instruments Incorporated POST OFFICE BOX 655 DALLAS, TEXAS 7565
2 SN7576A SLLSA JUNE 984 REVISED MAY 995 Function Tables DRIVER INPUT ENABLE OUTPUTS D DE A B H H H L L H L H X L Z Z RECEIVER DIFFERENTIAL INPUTS ENABLE OUTPUT A B RE R VID. V L H. V < VID <. V L? VID. V L L X H Z Open L? H = high level, L = low level,? = indeterminate, X = irrelevant, Z = high impedance (off) logic symbol logic diagram (positive logic) DE RE D 4 EN EN 6 7 A B DE D 4 RE R 6 7 A B Bus R This symbol is in accordance with ANSI/IEEE Std and IEC Publication 67-. POST OFFICE BOX 655 DALLAS, TEXAS 7565
3 SN7576A SLLSA JUNE 984 REVISED MAY 995 schematics of inputs and outputs EQUIVALENT OF EACH INPUT TYPICAL OF A AND B I/O PORTS TYPICAL OF RECEIVER OUTPUT VCC R(eq) VCC VCC 85 Ω NOM Input 6.8 kω NOM 96 Ω NOM 96 Ω NOM Driver input: R(eq) = kω NOM Enable inputs: R(eq) = 8 kω NOM R(eq) = equivalent resistor Input/ Port GND absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, V CC (see Note ) V Voltage range at any bus terminal to 5 V Enable input voltage, V I V Continuous total power dissipation See Dissipation Rating Table Operating free-air temperature range, T A C to 7 C Storage temperature range, T stg C to 5 C Lead temperature,6 mm (/6 inch) from case for seconds C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE : All voltage values, except differential input/output bus voltage, are with respect to network ground terminal. PACKAGE DISSIPATION RATING TABLE TA A 5 C DERATING FACTOR TA A = 7 C TA A = 5 C POWER RATING ABOVE TA = 5 C POWER RATING POWER RATING D 75 mw 5.8 mw/ C 464 mw 6 mw P mw 8.8 mw/ C 74 mw 96 mw POST OFFICE BOX 655 DALLAS, TEXAS 7565
4 SN7576A SLLSA JUNE 984 REVISED MAY 995 recommended operating conditions MIN TYP MAX UNIT Supply voltage, VCC V Voltage at any bus terminal (separately or common mode), VI or VIC 7 V High-level input voltage, VIH D, DE, and RE V Low-level input voltage, VIL D, DE, and RE.8 V Differential input voltage, VID (see Note ) ± V High-level output current, IOH Driver 6 ma Receiver 4 µa Low-level output current, IOL Driver 6 Receiver 8 ma Operating free-air temperature, TA 7 C NOTE : Differential-input/output bus voltage is measured at the noninverting terminal A with respect to the inverting terminal B. 4 POST OFFICE BOX 655 DALLAS, TEXAS 7565
5 SN7576A SLLSA JUNE 984 REVISED MAY 995 DRIVER SECTION electrical characteristics over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VIK Input clamp voltage II = 8 ma VIH = V, VIL =.8 V, VOH High-level output voltage IOH = ma VIH = V, VIL =.8 V, VOL Low-level output voltage IOH = ma 7.7 V. V VOD Differential output voltage IO = OD V VOD Differential output voltage RL = Ω, See Figure.7 RL = 54 Ω, See Figure.5.4 VOD Change in magnitude of differential output voltage ±. V VOC VOC IO Common-mode output voltage Change in magnitude of common-mode output voltage current RL = 54 Ω or Ω, See Figure disabled, VO = V See Note O = 7 V.8 V ±. V IIH High-level input current VI =.4 V µa IIL Low-level input current VI =.4 V 4 µa VO = 7 V 5 IOS Short-circuit output current VO = VCC 5 ma ICC Supply current (total package) No load VO = V 5 s enabled 5 5 s disabled 6 4 All typical values are at VCC = 5 V and TA = 5 C. VOD and VOC are the changes in magnitude of VOD and VOC respectively, that occur when the input is changed from a high level to a low level. In ANSI Standard EIA/TIA-4-B, VOC, which is the average of the two output voltages with respect to GND, is called output offset voltage, VOS. NOTE : This applies for both power on and off; refer to ANSI Standard EIA/TIA-4-B for exact conditions. switching characteristics, V CC = 5 V, T A = 5 C PARAMETER TEST CONDITIONS MIN TYP MAX UNIT td(od) Differential-output delay time 4 6 ns RL =6Ω Ω, See Figure tt(od) Differential-output transition time ns tpzh enable time to high level RL = Ω, See Figure ns tpzl enable time to low level RL = Ω, See Figure 5 5 ns tphz disable time from high level RL = Ω, See Figure 4 85 ns tplz disable time from low level RL = Ω, See Figure 5 4 ns ma ma POST OFFICE BOX 655 DALLAS, TEXAS
6 SN7576A SLLSA JUNE 984 REVISED MAY 995 RECEIVER SECTION electrical characteristics over recommended ranges of common-mode input voltage, supply voltage, and operating free-air temperature (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT VIT + Positive-going input threshold voltage VO =.7 V, IO =.4 ma. V VIT Negative-going input threshold voltage VO =.5 V, IO = 8 ma. V Vhys Input hysteresis voltage (VIT + VIT ) 5 mv VIK Enable clamp voltage II = 8 ma VID = mv, VOH High-level output voltage See Figure VID = mv, VOL Low-level output voltage See Figure IOH = 4 µa,, IOL = 8 ma, 7.7 V V IOZ High-impedance-state output current VO =.4 V to.4 V ± µa II Line input current Other input =, VI = V See Note I = 7 V.8 IIH High-level enable input current VIH =.7 V µa IIL Low-level enable input current VIL =.4 V µa ri Input resistance kω IOS Short-circuit output current 5 85 ma ICC Supply current (total package) No load s enabled 5 5 s disabled 6 4 All typical values are at VCC = 5 V, TA = 5 C. The algebraic convention, in which the less-positive (more-negative) limit is designated minimum, is used in this data sheet for common-mode input voltage and threshold voltage levels only. NOTE : This applies for both power on and power off. Refer to ANSI Standard EIA/TIA-4-B for exact conditions. switching characteristics, V CC = 5 V, C L = 5 pf, T A = 5 C ma ma tplh tphl tpzh tpzl tphz tplz PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Propagation delay time, low-to-high-level output 5 ns VID =.5 5Vto5V, See Figure 6 Propagation delay time, high-to-low-level output 5 ns enable time to high level ns See Figure 7 enable time to low level ns disable time from high level 5 ns See Figure 7 disable time from low level 7 5 ns 6 POST OFFICE BOX 655 DALLAS, TEXAS 7565
7 SN7576A PARAMETER MEASUREMENT INFORMATION SLLSA JUNE 984 REVISED MAY 995 VOD RL VID VOH RL VOC VOL +IOL IOH Figure. Driver V OD and V OC Figure. Receiver V OH and V OL Generator (see Note A) 5 Ω RL = 6 Ω CL = 5 pf (see Note B) CL Input td(od) 5% % tt(od) 9% td(od).5 V 5% %.5 V tt(od) TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR = MHz, 5% duty cycle, tr 6 ns, tf 6 ns, ZO = 5 Ω. B. CL includes probe and jig capacitance. Figure. Driver Test Circuit and Voltage Waveforms Generator (see Note A) or 5 Ω S CL = 5 pf (see Note B) RL = Ω Input tpzh. tphz.5 V VOH Voff TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR = MHz, 5% duty cycle, tr 6 ns, tf 6 ns, ZO = 5 Ω. B. CL includes probe and jig capacitance. Figure 4. Driver Test Circuit and Voltage Waveforms POST OFFICE BOX 655 DALLAS, TEXAS
8 SN7576A SLLSA JUNE 984 REVISED MAY 995 or Generator (see Note A) 5 Ω S CL = 5 pf (see Note B) 5 V RL = Ω Input tpzl. tplz 5 V.5 V VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR = MHz, 5% duty cycle, tr 6 ns, tf 6 ns, ZO = 5 Ω. B. CL includes probe and jig capacitance. Figure 5. Driver Test Circuit and Voltage Waveforms Generator (see Note A) 5 Ω CL = 5 pf (see Note B) Input tplh. tphl. VOH VOL TEST CIRCUIT VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR = MHz, 5% duty cycle, tr 6 ns, tf 6 ns, ZO = 5 Ω. B. CL includes probe and jig capacitance. Figure 6. Receiver Test Circuit and Voltage Waveforms 8 POST OFFICE BOX 655 DALLAS, TEXAS 7565
9 SN7576A SLLSA JUNE 984 REVISED MAY 995 S kω S 5 V CL = 5 pf (see Note B) 5 kω N96 or Equivalent Generator (see Note A) 5 Ω S TEST CIRCUIT Input tpzh S to S Open S Closed Input tpzl S to S Closed S Open VOH 4.5 V VOL Input S to S Closed S Closed Input S to S Closed S Closed tphz tplz.5 V VOH..5 V. VOL VOLTAGE WAVEFORMS NOTES: A. The input pulse is supplied by a generator having the following characteristics: PRR = MHz, 5% duty cycle, tr 6 ns, tf 6 ns, ZO = 5 Ω. B. CL includes probe and jig capacitance. Figure 7. Receiver Test Circuit and Voltage Waveforms POST OFFICE BOX 655 DALLAS, TEXAS
10 SN7576A SLLSA JUNE 984 REVISED MAY 995 TYPICAL CHARACTERISTICS VOH V High-Level Voltage V DRIVER HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT VCC = 5 V TA = 5 C V OL Low-Level Voltage V DRIVER LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT VCC = 5 V TA = 5 C IOH High-Level Current ma IOL Low-Level Current ma Figure 8 Figure 9 VOD V Differential Voltage V DRIVER DIFFERENTIAL OUTPUT VOLTAGE vs OUTPUT CURRENT VCC = 5 V TA = 5 C VOL V OL Low-Level Voltage V ÁÁ ÁÁ RECEIVER LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT VCC = 5 V TA = 5 C IO Current ma IOL Low Level Current ma Figure Figure POST OFFICE BOX 655 DALLAS, TEXAS 7565
11 SN7576A TYPICAL CHARACTERISTICS SLLSA JUNE 984 REVISED MAY 995 RECEIVER LOW-LEVEL OUTPUT VOLTAGE vs FREE-AIR TEMPERATURE RECEIVER OUTPUT VOLTAGE vs ENABLE VOLTAGE VOL V Low-Levcel Voltage V ÁÁ ÁÁ VCC = 5 V VID =. V IOL = 8 ma VO ÁÁVO Voltage V 5 4 VID =. V Load = 8 kω to GND TA = 5 C VCC = 5 V VCC = 5.5 V VCC = 4.75 V TA Free-Air Temperature C Figure VI Enable Voltage V Figure V VO O Voltage V ÁÁ VCC = 5.5 V VCC = 4.75 V RECEIVER OUTPUT VOLTAGE vs ENABLE VOLTAGE VID =. V Load = kω to VCC TA = 5 C VCC = 5 V VI Enable Voltage V Figure 4 POST OFFICE BOX 655 DALLAS, TEXAS 7565
12 SN7576A SLLSA JUNE 984 REVISED MAY 995 APPLICATION INFORMATION SN6576A SN6576A RT RT Up to Transceivers NOTE A: The line should be terminated at both ends in its characteristic impedance (RT = ZO). Stub lengths off the main line should be kept as short as possible. Figure 5. Typical Application Circuit POST OFFICE BOX 655 DALLAS, TEXAS 7565
13 PACKAGE OPTION ADDENDUM -Jun-5 PACKAGING INFORMATION Orderable Device Status () Package Type Package Drawing Pins Package Qty SN7576AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) SN7576ADE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) SN7576ADR ACTIVE SOIC D 8 5 Green (RoHS & no Sb/Br) SN7576ADRE4 ACTIVE SOIC D 8 5 Green (RoHS & no Sb/Br) SN7576AP ACTIVE PDIP P 8 5 Pb-Free (RoHS) SN7576APE4 ACTIVE PDIP P 8 5 Pb-Free (RoHS) Eco Plan () Lead/Ball Finish MSL Peak Temp () CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU CU NIPDAU Level--6C-UNLIM Level--6C-UNLIM Level--6C-UNLIM Level--6C-UNLIM Level-NC-NC-NC Level-NC-NC-NC () The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. () Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed.% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed.% by weight in homogeneous material) () MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page
14 MECHANICAL DATA MPDIA JANUARY 995 REVISED JUNE 999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 8.4 (,6).55 (9,) 5.6 (6,6).4 (6,) 4.7 (,78) MAX. (,5) MIN.5 (8,6). (7,6).5 (,8). (5,8) MAX Gage Plane Seating Plane.5 (,8) MIN. (,5) NOM. (,5).5 (,8). (,54). (,5) M.4 (,9) MAX 448/D 5/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS- For the latest package information, go to POST OFFICE BOX 655 DALLAS, TEXAS 7565
15
16 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio Data Converters dataconverter.ti.com Automotive DSP dsp.ti.com Broadband Interface interface.ti.com Digital Control Logic logic.ti.com Military Power Mgmt power.ti.com Optical Networking Microcontrollers microcontroller.ti.com Security Telephony Video & Imaging Wireless Mailing Address: Texas Instruments Post Office Box 655 Dallas, Texas 7565 Copyright 5, Texas Instruments Incorporated
SN65176B, SN75176B DIFFERENTIAL BUS TRANSCEIVERS
Bidirectional Transceivers Meet or Exceed the Requirements of ANSI Standards TIA/EIA--B and TIA/EIA-8-A and ITU Recommendations V. and X.7 Designed for Multipoint Transmission on Long Bus Lines in Noisy
More informationua9636ac DUAL LINE DRIVER WITH ADJUSTABLE SLEW RATE
SLLSB OCTOBER 9 REVISED MAY 995 Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-3-B and -3-E and ITU Recommendations V. and V. Output Slew Rate Control Output Short-Circuit-Current Limiting
More informationSN54ALS1035, SN74ALS1035 HEX NONINVERTING BUFFERS WITH OPEN-COLLECTOR OUTPUTS
Noninverting Buffers With Open-Collector Outputs description These devices contain six independent noninverting buffers. They perform the Boolean function Y = A. The open-collector outputs require pullup
More informationSN54ALS05A, SN74ALS05A HEX INVERTERS WITH OPEN-COLLECTOR OUTPUTS
SN54ALS05A, SN74ALS05A HEX INVERTERS WITH OPEN-COLLECTOR OUTPUTS SDAS190A APRIL 1982 REVISED DECEMBER 1994 Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard
More informationMC3486 QUADRUPLE DIFFERENTIAL LINE RECEIVER WITH 3-STATE OUTPUTS
Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-422-B and EIA/TIA-423-B and ITU Recommendations V.10 and V.11 3-State, TTL-Compatible s Fast Transition Times Operates From Single 5-V Supply
More informationSN75174 QUADRUPLE DIFFERENTIAL LINE DRIVER
SN Meets or Exceeds the Requirements of ANSI Standards EIA/TIA--B and RS-8 and ITU Recommendation V.. Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments -State s Common-Mode Voltage
More informationSN751177, SN DUAL DIFFERENTIAL DRIVERS AND RECEIVERS
SN7577, SN7578 Meet or Exceed the Requirements of ANSI Standards TIA/EIA-4-B and TIA/EIA-485-A and ITU Recommendations V.0 and V. Designed for Multipoint Bus Transmission on Long Bus Lines in Noise Environments
More informationSN65176B, SN75176B DIFFERENTIAL BUS TRANSCEIVERS
SN676B, SN776B Bidirectional Transceivers Meet or Exceed the Requirements of ANSI Standards TIA/EIA--B and TIA/EIA-8-A and ITU Recommendations V. and X.7 Designed for Multipoint Transmission on Long Bus
More informationMC3487 QUADRUPLE DIFFERENTIAL LINE DRIVER
Meets or Exceeds Requirements of ANSI EIA/TIA-422-B and ITU Recommendation V. -State, TTL-Compatible s Fast Transition Times High-Impedance Inputs Single -V Supply Power-Up and Power-Down Protection Designed
More informationAM26LS31 QUADRUPLE DIFFERENTIAL LINE DRIVER
AM6LS SLLSG JANUARY 979 REVISED FEBRUARY Meets or Exceeds the Requirements of ANSI TIA/EIA--B and ITU Recommendation V. Operates From a Single -V Supply TTL Compatible Complementary Outputs High Output
More informationCD54AC08, CD74AC08 QUADRUPLE 2-INPUT POSITIVE-AND GATES
CD54AC08, CD74AC08 QUADRUPLE 2-INPUT POSITIVE-AND GATES AC Types Feature 1.5-V to 5.5-V Operation and Balanced Noise Immunity at 30% of the Supply Voltage Speed of Bipolar F, AS, and S, With Significantly
More informationSN75160B OCTAL GENERAL-PURPOSE INTERFACE BUS TRANSCEIVER
Meets IEEE Standard 488-978 (GPIB) 8-Channel Bidirectional Transceiver Power-Up/Power-Down Protection (Glitch Free) High-Speed, Low-Power Schottky Circuitry Low Power Dissipation...7 mw Max Per Channel
More informationMSP53C391, MSP53C392 SLAVE SPEECH SYNTHESIZERS
Slave Speech Synthesizers, LPC, MELP, CELP Two Channel FM Synthesis, PCM 8-Bit Microprocessor With 61 instructions 3.3V to 6.5V CMOS Technology for Low Power Dissipation Direct Speaker Drive Capability
More information2 C Accurate Digital Temperature Sensor with SPI Interface
TMP125 2 C Accurate Digital Temperature Sensor with SPI Interface FEATURES DIGITAL OUTPUT: SPI-Compatible Interface RELUTION: 10-Bit, 0.25 C ACCURACY: ±2.0 C (max) from 25 C to +85 C ±2.5 C (max) from
More informationCD74HCT4543 BCD-TO-7 SEGMENT LATCH/DECODER/DRIVER
4.5-V to 5.5-V V CC Operation Input Latches for BCD Code Storage Blanking Capability Phase Input for Complementing s Fanout (Over Temperature Range) Standard s 10 LSTTL Loads Balanced Propagation Delay
More informationua9637ac DUAL DIFFERENTIAL LINE RECEIVER
ua967ac Meets or Exceeds the Requirements of ANSI Standards EIA/TIA--B and EIA/TIA--B and ITU Recommendations V. and V. Operates From Single -V Power Supply Wide Common-Mode Voltage Range High Input Impedance
More informationTIB82S105BC FIELD-PROGRAMMABLE LOGIC SEQUENCER WITH 3-STATE OUTPUTS OR PRESET
50-MHz Clock Rate Power-On Preset of All Flip-Flops -Bit Internal State Register With -Bit Output Register Power Dissipation... 00 mw Typical Programmable Asynchronous Preset or Output Control Functionally
More informationDistributed by: www.jameco.com -8-8-44 The content and copyrights of the attached material are the property of its owner. Bidirectional Transceivers Meet or Exceed the Requirements of ANSI Standards TIA/EIA-4-B
More informationSN75158 DUAL DIFFERENTIAL LINE DRIVER
SN78 Meets or Exceeds the Requirements of ANSI EIA/TIA--B and ITU Recommendation V. Single -V Supply Balanced-Line Operation TTL Compatible High Output Impedance in Power-Off Condition High-Current Active-Pullup
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. 500-mA Rated Collector Current (Single Output) High-Voltage Outputs...50
More informationSN5414, SN54LS14, SN7414, SN74LS14 HEX SCHMITT-TRIGGER INVERTERS
Operation From Very Slow Edges Improved Line-Receiving Characteristics High Noise Immunity SN5414, SN54LS14, SN5414, SN54LS14...J OR W PACKAGE SN7414... D, N, OR NS PACKAGE SN74LS14... D, DB, OR N PACKAGE
More informationThe ULN2003AI has a 2.7-kΩ series base resistor for each Darlington pair for operation directly with TTL or 5-V CMOS devices. ORDERING INFORMATION
查询 ULN23AI 供应商 www.ti.com FEATURES 5-mA-Rated Collector Current (Single Output) High-Voltage Outputs... 5 V Output Clamp Diodes Inputs Compatible With Various Types of Logic Relay-Driver Applications DESCRIPTION/ORDERING
More informationSN54ACT573, SN74ACT573 OCTAL D-TYPE TRANSPARENT LATCHES WITH 3-STATE OUTPUTS
4.5-V to 5.5-V V CC Operation Inputs Accept Voltages to 5.5 V Max t pd of 9.5 ns at 5 V Inputs Are TTL-Voltage Compatible description/ordering information These 8-bit latches feature 3-state outputs designed
More informationSN54HCT14, SN74HCT14 HEX SCHMITT-TRIGGER INVERTERS
SN54HCT14, SN74HCT14 HEX SCHMITT-TRIGGER INVERTERS SCLS225E JULY 1995 REVISED JULY 2003 Operating Voltage Range of 4.5 V to 5.5 V Outputs Can Drive Up To 10 LSTTL Loads Low Power Consumption, 20-µA Max
More informationSN54ALS804A, SN54AS804B, SN74ALS804A, SN74AS804B HEX 2-INPUT NAND DRIVERS
SN54ALS804A, SN54AS804B, SN74ALS804A, SN74AS804B HEX 2-INPUT NAND DRIVERS SDAS022C DECEMBER 1982 REVISED JANUARY 1995 High Capacitive-Drive Capability ALS804A Has Typical Delay Time of 4 ns (C L = 50 pf)
More informationHIGH-VOLTAGE HIGH-CURRENT DARLINGTON TRANSISTOR ARRAYS
SLRS3D DECEMBER 976 REVISED NOVEMBER 4 HIGH-VOLTAGE HIGH-CURRENT DARLINGTON TRANSISTOR ARRAYS 5-mA Rated Collector Current (Single Output) High-Voltage Outputs... V Output Clamp Diodes Inputs Compatible
More information54ACT16827, 74ACT BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
Members of the Texas Instruments Widebus Family Inputs Are TTL-Voltage Compatible 3-State Outputs Drive Bus Lines Directly Flow-Through Architecture Optimizes PCB Layout Distributed V CC and Pin Configuration
More informationOUTPUT INPUT ADJUSTMENT INPUT INPUT ADJUSTMENT INPUT
www.ti.com FEATURES LM237, LM337 3-TERMINAL ADJUSTABLE REGULATORS SLVS047I NOVEMBER 1981 REVISED OCTOBER 2006 Output Voltage Range Adjustable From Peak Output Current Constant Over 1.2 V to 37 V Temperature
More informationSN75ALS192 QUADRUPLE DIFFERENTIAL LINE DRIVER
SN7ALS9 Meets or Exceeds the Requirements of ANSI Standard EIA/TIA--B and ITU Recommendation V. Designed to Operate up to Mbaud -State TTL Compatible Single -V Supply Operation High Output Impedance in
More informationSN54ALS541, SN74ALS540, SN74ALS541 OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS
SN54ALS541, SN74ALS540, SN74ALS541 OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS SDAS025D APRIL 1982 REVISED MARCH 2002 3-State Outputs Drive Bus Lines or Buffer Memory Address Registers pnp Inputs
More informationORDERING INFORMATION PACKAGE
SN74CBT16214 12-BIT 1-OF-3 FET MULTIPLEXER/DEMULTIPLEXER SCDS008L MAY 1993 REVISED NOVEMBER 2001 Member of the Texas Instruments Widebus Family 5-Ω Switch Connection Between Two Ports TTL-Compatible Input
More informationSN65ALS1176 DIFFERENTIAL BUS TRANSCEIVER
Meets or Exceeds the Requirements of TIA/EIA-422-B, TIA/EIA-485-A, and ITU Recommendations V.11 and X.27 Recommended for PROFIBUS Applications Operates at Data Rates up to 35 MBaud Operating Temperature
More informationSN54ALS193A, SN74ALS193A SYNCHRONOUS 4-BIT UP/DOWN BINARY COUNTERS WITH DUAL CLOCK AND CLEAR
Look-Ahead Circuitry Enhances Cascaded Counters Fully Synchronous in Count Modes Parallel Asynchronous Load for Modulo-N Count Lengths Asynchronous Clear Package Options Include Plastic Small-Outline (D)
More informationSN54ALS32, SN54AS32, SN74ALS32, SN74AS32 QUADRUPLE 2-INPUT POSITIVE-OR GATES
SN54ALS32, SN54AS32, SN74ALS32, SN74AS32 QUADRUPLE 2-INPUT POSITIVE-OR GATES SDAS113B APRIL 1982 REVISED DECEMBER 1994 Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers
More informationSN75150 DUAL LINE DRIVER
Meets or Exceeds the Requirement of ANSI EIA/TIA-232-E and ITU Recommendation V.28 Withstands Sustained Output Short Circuit to Any Low-Impedance Voltage Between 25 V and 25 V 2-µs Max Transition Time
More informationDistributed by: www.jameco.com 1-8-831-4242 The content and copyrights of the attached material are the property of its owner. SLRS28A SEPTEMBER 1988 REVISED NOVEMBER 24 Quadruple Circuits Capable of Driving
More informationSN65176B, SN75176B DIFFERENTIAL BUS TRANSCEIVERS
Bidirectional Transceivers Meet or Exceed the Requirements of ANSI Standards TIA/EIA-4-B and TIA/EIA-485-A and ITU Recommendations V.11 and X.7 Designed for Multipoint Transmission on Long Bus Lines in
More informationSN54LS245, SN74LS245 OCTAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS
3-State s Drive Bus Lines Directly PNP s Reduce dc Loading on Bus Lines Hysteresis at Bus s Improves Noise Margins Typical Propagation Delay Times Port to Port, 8 ns TYPE IOL (SINK CURRENT) IOH (SOURCE
More informationSN55451B, SN55452B, SN55453B, SN55454B SN75451B, SN75452B, SN75453B, SN75454B DUAL PERIPHERAL DRIVERS
PERIPHERAL DRIVERS FOR HIGH-CURRENT SWITCHING AT VERY HIGH SPEEDS Characterized for Use to 00 ma High-Voltage Outputs No Output Latch-Up at 0 V (After Conducting 00 ma) High-Speed Switching Circuit Flexibility
More information4423 Typical Circuit A2 A V
SBFS020A JANUARY 1978 REVISED JUNE 2004 FEATURES Sine and Cosine Outputs Resistor-Programmable Frequency Wide Frequency Range: 0.002Hz to 20kHz Low Distortion: 0.2% max up to 5kHz Easy Adjustments Small
More informationMC3486 QUADRUPLE DIFFERENTIAL LINE RECEIVER WITH 3-STATE OUTPUTS
Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-422-B and EIA/TIA-423-B and ITU Recommendations V.10 and V.11 3-State, TTL-Compatible s Fast Transition Times Operates From Single 5-V Supply
More informationdescription/ordering information
Equivalent Input Noise Voltage 5 nv/ Hz Typ at 1 khz Unity-Gain Bandwidth... 10 MHz Typ Common-Mode Rejection Ratio... 100 db Typ High dc Voltage Gain... 100 V/mV Typ Peak-to-Peak Output Voltage Swing
More informationSN74AUC1G07 SINGLE BUFFER/DRIVER WITH OPEN-DRAIN OUTPUT
www.ti.com FEATURES SN74AUC1G07 SINGLE BUFFER/DRIVER WITH OPEN-DRAIN OUTPUT SCES373O SEPTEMBER 2001 REVISED FEBRUARY 2007 Available in the Texas Instruments Low Power Consumption, 10-µA Max I CC NanoFree
More informationua9637ac DUAL DIFFERENTIAL LINE RECEIVER
ua9637ac DUAL DIFFERENTIAL LINE RECEIVER Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-422-B and EIA/TIA-423-B and ITU Recommendations V.10 and V.11 Operates From Single 5-V Power Supply
More informationSN75177B, SN75178B DIFFERENTIAL BUS REPEATERS
SN777B, SN778B SLLSC D66, JULY 98 REVISED FEBRUARY 99 Meets EIA Standards RS--A and RS-8 and CCITT Recommendations V. and X.7 Designed for Multipoint Transmission on Long Bus Lines in Noisy Environments
More informationSN54ALS374A, SN54AS374, SN74ALS374A, SN74AS374 OCTAL D-TYPE EDGE-TRIGGERED FLIP-FLOPS WITH 3-STATE OUTPUTS
D-Type Flip-Flops in a Single Package With 3-State Bus Driving True Outputs Full Parallel Access for Loading Buffered Control Inputs Package Options Include Plastic Small-Outline (DW) Packages, Ceramic
More informationPOSITIVE-VOLTAGE REGULATORS
www.ti.com FEATURES µa78m00 SERIES POSITIVE-VOLTAGE REGULATORS SLVS059P JUNE 1976 REVISED OCTOBER 2005 3-Terminal Regulators High Power-Dissipation Capability Output Current up to 500 ma Internal Short-Circuit
More informationSN5407, SN5417, SN7407, SN7417 HEX BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS
Converts TTL Voltage Levels to MOS Levels High Sink-Current Capability Clamping Diodes Simplify System Design Open-Collector Driver for Indicator Lamps and Relays s Fully Compatible With Most TTL Circuits
More informationSN65ALS176, SN75ALS176, SN75ALS176A, SN75ALS176B DIFFERENTIAL BUS TRANSCEIVERS
SN65ALS176, SN75ALS176, SN75ALS176A, SN75ALS176B DIFFERENTIAL BUS TRANSCEIVERS SLLS040H AUGUST 1987 REVISED JUNE 2000 Meet or Exceed the Requirements of TIA/EIA-422-B, TIA/EIA-485-A and ITU Recommendations
More informationdescription/ordering information
SLLS047L FEBRUARY 1989 REVISED MARCH 2004 Meets or Exceeds TIA/EIA-232-F and ITU Recommendation V.28 Operates From a Single 5-V Power Supply With 1.0-F Charge-Pump Capacitors Operates Up To 120 kbit/s
More informationEN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at ore.hu.
EN: This Datasheet is presented by the m anufacturer. Please v isit our website for pricing and availability at www.hest ore.hu. Convert TTL Voltage Levels to MOS Levels High Sink-Current Capability Clamping
More informationLM317M 3-TERMINAL ADJUSTABLE REGULATOR
FEATURES Output Voltage Range Adjustable From 1.25 V to 37 V Output Current Greater Than 5 ma Internal Short-Circuit Current Limiting Thermal-Overload Protection Output Safe-Area Compensation Q Devices
More informationCD74HCT4514, CD74HCT LINE TO 16-LINE DECODERS/DEMULTIPLEXERS WITH INPUT LATCHES
4.5-V to 5.5-V V CC Operation Fanout (Over Temperature Range) Standard s... 0 LSTTL Loads Bus-Driver s... 5 LSTTL Loads Wide Operating Temperature Range of 55 C to 25 C Balanced Propagation Delays and
More informationCDC337 CLOCK DRIVER WITH 3-STATE OUTPUTS
Low Output Skew, Low Pulse Skew for Clock-Distribution and Clock-Generation Applications TTL-Compatible Inputs and CMOS-Compatible Outputs Distributes One Clock Input to Eight Outputs Four Same-Frequency
More informationdescription 1G 1A1 2Y4 1A2 2Y3 1A3 2Y2 1A4 2Y1 GND V CC 2G/2G 1Y1 2A4 1Y2 2A3 1Y3 2A2 1Y4 2A1 1Y1 2A4 1Y2 2A3 1Y3 1A2 2Y3 1A3 2Y2 1A4 2A2 2G/2G 2Y1
SN54LS240, SN54LS241, SN54LS244, SN54S240, SN54S241, SN54S244 3-State s Drive Bus Lines or Buffer Memory Address Registers PNP s Reduce DC Loading Hysteresis at s Improves Noise Margins description These
More informationSN65LVDM31 HIGH-SPEED DIFFERENTIAL LINE DRIVER
HIH-SPEED DIFFERENTIAL LINE DRIVER Designed for Signaling Rates Up to 5 Mbps Low-Voltage Differential Signaling With Typical Output Voltage of 7 mv and a -Ω Load Propagation Delay Time of. ns, Typical
More informationSN75157 DUAL DIFFERENTIAL LINE RECEIVER
SN75157 DUAL DIFFERENTIAL LINE RECEIVER Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-422-B and EIA/TIA-423-B and ITU Recommendation V.1 and V.11 Operates From Single 5-V Power Supply Wide
More informationSN54ALS174, SN54ALS175, SN54AS174, SN54AS175B SN74ALS174, SN74ALS175, SN74AS174, SN74AS175B HEX/QUADRUPLE D-TYPE FLIP-FLOPS WITH CLEAR
ALS174 and AS174 Contain Six Flip-Flops With Single-Rail Outputs ALS175 and AS175B Contain Four Flip-Flops With Double-Rail Outputs Buffered Clock and Direct-Clear Inputs SN54ALS174, SN54ALS175, SN54AS174,
More informationORDERING INFORMATION SOT (SOT-23) DBV SOT (SC-70) DCK
www.ti.com FEATURES Available in the Texas Instruments NanoStar and NanoFree Packages Supports 5-V V CC Operation Inputs Accept Voltages to 5.5 V Max t pd of 4.1 ns at 3.3 V Low Power Consumption, 10-µA
More informationSN74LVC2244ADWR OCTAL BUFFER/DRIVER WITH 3-STATE OUTPUTS. description/ordering information
Operates From 1.65 V to 3.6 V Inputs Accept Voltages to 5.5 V Max t pd of 5.5 ns at 3.3 V Output Ports Have Equivalent 26-Ω Series Resistors, So No External Resistors Are Required Typical V OLP (Output
More informationSN5406, SN5416, SN7406, SN7416 HEX INVERTER BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS SDLS031A DECEMBER 1983 REVISED DECEMBER 2001
SN5406, SN5416, SN7406, SN7416 HEX INVERTER BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS SDLS031A DECEMBER 1983 REVISED DECEMBER 2001 Convert TTL Voltage Levels to MOS Levels High Sink-Current
More informationSN54HC541, SN74HC541 OCTAL BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS
Wide Operating Voltage Range of 2 V to 6 V High-Current 3-State Outputs Drive Bus Lines Directly or Up To 15 LSTTL Loads Low Power Consumption, 80-µA Max I CC Typical t pd = 10 ns ±6-mA Output Drive at
More informationSN75158 DUAL DIFFERENTIAL LINE DRIVER
SN7558 DUAL DIFFERENTIAL LINE DRIVER Meets or Exceeds the Requirements of ANSI EIA/TIA-422-B and ITU Recommendation V. Single 5-V Supply Balanced-Line Operation TTL Compatible High Output Impedance in
More informationSN54HC365, SN74HC365 HEX BUFFERS AND LINE DRIVERS WITH 3-STATE OUTPUTS
High-Current -State s Drive Bus Lines, Buffer Memory Address Registers, or Drive up to LSTTL Loads True s Package Options Include Plastic Small-Outline (D) and Ceramic Flat (W) Packages, Ceramic Chip Carriers
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. SLLS094C SEPTEMBER 1983 REVISED MAY 2004 Meet or Exceed the Requirements
More information1OE 3B V GND ORDERING INFORMATION. TOP-SIDE MARKING QFN RGY Tape and reel SN74CBTLV3126RGYR CL126 PACKAGE
SN74CBTLV326 LOW-VOLTAGE QUADRUPLE FET BUS SWITCH SCDS03H DECEMBER 997 REVISED APRIL 2003 Standard 26-Type Pinout 5-Ω Switch Connection Between Two Ports Isolation Under Power-Off Conditions Latch-up Performance
More informationSN5407, SN5417, SN7407, SN7417 HEX BUFFERS/DRIVERS WITH OPEN-COLLECTOR HIGH-VOLTAGE OUTPUTS SDLS032A DECEMBER 1983 REVISED NOVEMBER 1997
Converts TTL Voltage Levels to MOS Levels High Sink-Current Capability Clamping Diodes Simplify System Design Open-Collector Driver for Indicator Lamps and Relays s Fully Compatible With Most TTL Circuits
More informationSN75174 QUADRUPLE DIFFERENTIAL LINE DRIVER
SN7574 QUADRUPLE DIFFERENTIAL LINE DRIVER Meets or Exceeds the Requirements of ANSI Standards EIA/TIA-422-B and RS-485 and ITU Recommendation V.. Designed for Multipoint Transmission on Long Bus Lines
More informationdescription/ordering information
Dependable Texas Instruments Quality and Reliability description/ordering information These devices contain six independent inverters. SDLS029C DECEMBER 1983 REVISED JANUARY 2004 SN5404... J PACKAGE SN54LS04,
More informationSN74LVC1G18 1-OF-2 NONINVERTING DEMULTIPLEXER WITH 3-STATE DESELECTED OUTPUT
www.ti.com FEATURES Available in the Texas Instruments NanoStar and NanoFree Packages Supports 5-V Operation Inputs Accept Voltages to 5.5 V Max t pd of 3.4 ns at 3.3 V Low Power Consumption, 10-µA Max
More informationSN74ACT CLOCKED FIRST-IN, FIRST-OUT MEMORY
Member of the Texas Instruments Widebus Family Independent Asynchronous Inputs and Outputs Read and Write Operations Can Be Synchronized to Independent System Clocks Programmable Almost-Full/Almost-Empty
More informationMC1489, MC1489A, SN55189, SN55189A, SN75189, SN75189A QUADRUPLE LINE RECEIVERS
MC489, MC489A, SN5589, SN5589A, SN7589, SN7589A QUADRUPLE LINE RECEIVERS SLLS095D SEPTEMBER 973 REVISED OCTOBER 998 Input Resistance...3 kω to 7 kω Input Signal Range...±30 V Operate From Single 5-V Supply
More informationSN55115, SN75115 DUAL DIFFERENTIAL RECEIVERS
SN, SN7 Choice of Open-Collector or Active Pullup (Totem-Pole) Outputs Single -V Supply Differential Line Operation Dual-Channel Operation TTL Compatible ± -V Common-Mode Input Voltage Range Optional-Use
More informationdescription/ordering information
Meets or Exceeds TIA/EIA-232-F and ITU Recommendation V.28 Operates From a Single 5-V Power Supply With 1.0-F Charge-Pump Capacitors Operates Up To 120 kbit/s Two Drivers and Two Receivers ±30-V Input
More informationSN75LV4737A 3.3-V/5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
Single-Chip and Single-Supply Interface for IBM PC/AT Serial Port Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.11 Standards Operates With 3.3-V or 5-V Supplies One Receiver Remains Active
More informationMAX211 5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION
ESD Protection for RS-232 Bus Pins ±5 kv, Human-Body Model Meets or Exceeds the Requirements of TIA/EIA-232-F and ITU v.28 Standards Operates at 5-V V CC Supply Four Drivers and Five Receivers Operates
More informationSN54HC126, SN74HC126 QUADRUPLE BUS BUFFER GATES WITH 3-STATE OUTPUTS
SN54HC26, SN74HC26 QUADRUPLE BUS BUFFER GATES WITH 3-STATE OUTPUTS SCLS03E MARCH 94 REVISED JULY 2003 Wide Operating Voltage Range of 2 V to 6 V High-Current 3-State Outputs Interface Directly With System
More informationSN54HC00, SN74HC00 QUADRUPLE 2-INPUT POSITIVE-NAND GATES
SN54HC00, SN74HC00 QUADRUPLE 2-INPUT POSITIVE-NAND GATES SCLS181E DECEMBER 1982 REVISED AUGUST 2003 Wide Operating Voltage Range of 2 V to 6 V Outputs Can Drive Up To 10 LSTTL Loads Low Power Consumption,
More informationSN54HC245, SN74HC245 OCTAL BUS TRANSCEIVERS WITH 3-STATE OUTPUTS
High-Current -State s Drive Bus Lines Directly or up to LSTTL Loads Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline (DB), Thin Shrink Small-Outline (PW), and Ceramic Flat (W) Packages,
More informationSN75C185 LOW-POWER MULTIPLE DRIVERS AND RECEIVERS
Meets or Exceeds the Requirements of ANSI EIA/TIA-232-E and ITU Recommendation V.28 Single Chip With Easy Interface Between UART and Serial Port Connector Less Than 9-mW Power Consumption Wide Driver Supply
More informationORDERING INFORMATION TOP-SIDE
SCES JULY Control Inputs V IH /V IL Levels are Referenced to V CCA Voltage V CC Isolation Feature If Either V CC Input Is at, Both Ports Are in the High-Impedance State Overvoltage-Tolerant Inputs/Outputs
More informationORDERING INFORMATION. SSOP DCT Reel of 3000 SN74LVC2G125DCTR C25 _
www.ti.com FEATURES Available in the Texas Instruments NanoStar and NanoFree Packages Supports 5-V V CC Operation Inputs Accept Voltages to 5.5 V Max t pd of 4.3 ns at 3.3 V Low Power Consumption, 10-µA
More informationSN75150 DUAL LINE DRIVER
Meets or Exceeds the Requirement of TIA/EIA-232-F and ITU Recommendation V.28 Withstands Sustained Output Short Circuit to Any Low-Impedance Voltage Between 25 V and 25 V 2-µs Maximum Transition Time Through
More informationdescription/ordering information
Featuring Unitrode L9 and L9D Products Now From Texas Instruments Wide Supply-Voltage Range: 4.5 V to 6 V Separate Input-Logic Supply Internal ESD Protection Thermal Shutdown High-Noise-Immunity Inputs
More informationSN75471 THRU SN75473 DUAL PERIPHERAL DRIVERS
SN747 THRU SN747 DUAL PERIPHERAL DRIVERS SLRS024 DECEMBER 976 REVISED MAY 990 PERIPHERAL DRIVERS FOR HIGH-VOLTAGE HIGH-CURRENT DRIVER APPLICATIONS Characterized for Use to 00 ma High-Voltage Outputs No
More informationdescription/ordering information
Member of the Texas Instruments Widebus Family Max t pd of 5.8 ns at 3.3 ±24-mA Drive at 3.3 Latch-Up Performance Exceeds 250 ma Per JESD 17 description/ordering information This 16-bit (dual-octal) noninverting
More informationSN QUADRUPLE HALF-H DRIVER
-A -Current Capability Per Driver Applications Include Half-H and Full-H Solenoid Drivers and Motor Drivers Designed for Positive-Supply Applications Wide Supply-Voltage Range of 4.5 V to 6 V TTL- and
More informationSN54HC164, SN74HC164 8-BIT PARALLEL-OUT SERIAL SHIFT REGISTERS
SN54HC164, SN74HC164 8-BIT PARALLEL-OUT SERIAL SHIFT REGISTERS SCLS115D DECEMBER 1982 REVISED AUGUST 2003 Wide Operating Voltage Range of 2 V to 6 V Outputs Can Drive Up To 10 LSTTL Loads Low Power Consumption,
More informationORDERING INFORMATION PACKAGE
Member of Texas Instruments Widebus Family State-of-the-Art Advanced Low-Voltage BiCMOS (ALB) Technology Design for.-v Operation Schottky Diodes on All s to Eliminate Overshoot and Undershoot Industry
More informationL293, L293D QUADRUPLE HALF-H DRIVERS
Featuring Unitrode L and LD Products Now From Texas Instruments Wide Supply-Voltage Range:.5 V to V Separate Input-Logic Supply Internal ESD Protection Thermal Shutdown High-Noise-Immunity Inputs Functional
More informationSN54ALS08, SN54AS08, SN74ALS08, SN74AS08 QUADRUPLE 2-INPUT POSITIVE-AND GATES
SNALS0, SNAS0, SN7ALS0, SN7AS0 Package Options Include Plastic Small-Outline (D) Packages, Ceramic Chip Carriers (FK), and Standard Plastic (N) and Ceramic (J) 00-mil DIPs description These devices contain
More informationORDERING INFORMATION. 40 C to 85 C TSSOP DGG Tape and reel SN74LVCH16245ADGGR LVCH16245A TVSOP DGV Tape and reel SN74LVCH16245ADGVR LDH245A
www.ti.com FEATURES Member of the Texas Instruments Widebus Family Operates From 1.65 V to 3.6 V Inputs Accept Voltages to 5.5 V Max t pd of 4 ns at 3.3 V Typical V OLP (Output Ground Bounce) < 0.8 V at
More informationMAX232, MAX232I DUAL EIA-232 DRIVER/RECEIVER
Operates With Single 5-V Power Supply LinBiCMOS Process Technology Two Drivers and Two Receivers ± 30-V Input Levels Low Supply Current...8 ma Typical Meets or Exceeds TIA/EIA-232-F and ITU Recommendation
More informationSN54HC373, SN74HC373 OCTAL TRANSPARENT D-TYPE LATCHES WITH 3-STATE OUTPUTS
Eight High-Current Latches in a Single Package High-Current -State True s Can Drive up to LSTTL Loads Full Parallel Access for Loading Package Options Include Plastic Small-Outline (DW), Shrink Small-Outline
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. Member of the Texas Instruments Widebus Family Operates From 1.65 V to 3.6
More informationdescription/ordering information
Dependable Texas Instruments Quality and Reliability description/ordering information These devices contain six independent inverters. SN5404... J PACKAGE SN54LS04, SN54S04... J OR W PACKAGE SN7404, SN74S04...
More informationSN75207B DUAL SENSE AMPLIFIER FOR MOS MEMORIES OR DUAL HIGH-SENSITIVITY LINE RECEIVERS
Plug-In Replacement for SN75107A and SN75107B With Improved Characteristics ± 10-mV Input Sensitivity TTL-Compatible Circuitry Standard Supply Voltages... ±5 V Differential Input Common-Mode Voltage Range
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. www.ti.com FEATURES SN74LVC1G14 SINGLE SCHMITT-TRIGGER INVERTER SCES218S
More informationSealed Lead-Acid Battery Charger
Sealed Lead-Acid Battery Charger application INFO available UC2906 UC3906 FEATURES Optimum Control for Maximum Battery Capacity and Life Internal State Logic Provides Three Charge States Precision Reference
More informationTPIC6B273 POWER LOGIC OCTAL D-TYPE LATCH
POWER LOGIC OCTAL -TYPE LATCH Low r S(on)...5 Ω Typical Avalanche Energy...30 mj Eight Power MOS-Transistor Outputs of 50-mA Continuous Current 500-mA Typical Current-Limiting Capability Output Clamp Voltage...
More information