Installation. AccuSine SWP A Autotransformer for 208 V Mains

Transcription

1 Installation AuSine SWP A Autotransformer for 08 V Mains

2

3 Tale of Contents IMPORTAT SAFETY ISTRUCTIOS - SAVE THESE ISTRUCTIOS... Symols Used... Speifiations... Mehanial Assemly... Protetions... 4 Connetion to AuSine SWP 0 A Terminal Blok... 5 Connetion to AuSine SWP 0 A Terminal Blok... 7 Connetion to AuSine SWP 45 A Terminal Blok... 9 Connetion to AuSine SWP 60 A Terminal Blok... Connetion to AuSine SWP 90 A Terminal Blok with on-distriuted eutral... Connetion to AuSine SWP 90 A Terminal Blok with Distriuted eutral...4 Connetion to AuSine SWP 0 A Terminal Blok with on-distriuted eutral...5 Connetion to AuSine SWP 0 A Terminal Blok with Distriuted eutral...6 Cales...7 Power Connetions...8 Single Line Diagrams...9 Example of 0 A, 0 A, 45 A or 60 A Ative Harmoni Filter...0 Example of 90 A or 0 A Ative Harmoni Filter... Example of Two 0 A, 0 A, 45 A or 60 A Ative Harmoni Filters in Parallel... Example of Two 90 A or 0 A Ative Harmoni Filters in Parallel... Connet Autotransformer AuSine SWP A Autotransformer for 08 V Mains Installation i

4 ii AuSine SWP A Autotransformer for 08 V Mains Installation

5 IMPORTAT SAFETY ISTRUCTIOS - SAVE THESE ISTRUCTIOS WARIG: Hazardous voltages are present inside the autotransformer. Work on this equipment should only e arried out y qualified personnel. The autotransformer must e earthed. Do not install the autotransformer near liquids or in exessively damp environments. Do not ostrut the air vents. Do not plae the autotransformer in diret sunlight or near soures of heat. If the autotransformer is to e stored efore use, it must e kept in a dry, dust-free loation. Storage temperature: etween 0ºC and +45ºC. Symols Used WARIG: Indiates an eletrial hazard, whih, if not avoided, ould result in injury or death. Caution: Indiates a hazard, whih, if not avoided, ould result in injury or death. ote: Indiates important information. See: Indiates that more information is availale on the sujet AuSine SWP A Autotransformer for 08 V Mains Installation

6 Speifiations The performane data given in the tale elow are typial values orresponding to use under a nominal phase 50 Hz mains voltage of 08 volts and rated urrent. Input ominal voltage 08 V -0% +5% ominal frequeny 50 Hz, 60 Hz +/-5% umer of phases phases with or without neutral Tehnial Charateristis Inrush urrent Losses Ventilation < 0 times the rated peak urrent 0 A and 0 A 45 A and 60 A 90 A and 0 A < 50 W < 000 W < 50 W atural onvetion Environmental Conditions Amient temperature Relative humidity Operating altitude < 5ºC reommended 0 to 40ºC ontinuous 0 to 95% relative humidity without ondensation < 000 m Dimensions and Weight 0 A and 0 A 45 A and 60 A 90 A and 0 A Height 70 mm 45 mm 590 mm Length 60 mm 40 mm 590 mm Width 00 mm 0 mm 560 mm Weight 70 kg 5 kg 95 kg AuSine SWP A Autotransformer for 08 V Mains Installation

7 Mehanial Assemly The autotransformer is supplied without a protetive over. Dimensions (mm) Distanes etween hole entres (mm) Height A Length B Width D C E F Autotransformer for 0 A and 0 A AuSine SWP Ative Filter Hole diameters (4 mounting holes) Autotransformer for 45 A and 60 A AuSine SWP Ative Filter Autotransformer for 90 A and 0 A AuSine SWP Ative Filter Weight (kg) AuSine SWP A Autotransformer for 08 V Mains Installation

8 Protetions ote: Protetions shall e determined in ompliane with the standards in fore using the information elow and respeting disrimination onstraints. Speifi models are ited only as a general indiation and do not engage the responsiility of Shneider Eletri. ote: If protetion is provided y fuses, the fuse holder must e of the open type to allow for fuse ooling. ote: Is = sizing urrent Pu = reaking apaity Is = short-iruit urrent Pu = funtion of Is 4 AuSine SWP A Autotransformer for 08 V Mains Installation

9 Connetion to AuSine SWP 0 A Terminal Blok on-distriuted neutral Distriuted neutral IT Earthing System IT Earthing System 08 V A 50 A B C 5 A a A UR 5 A 08 V A 50 A B C 5 A 5 A a A UR 65 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: In = 50A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C60 50A P D urve TT Earthing System CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A 4poles / poles proteted - Thermal threshold : Ir = 6A - Magneti Threshold : Im= 5 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd - Trip Unit : Mirologi 60A / Ir Setup=6A TT Earthing System 08 V A 50 A B C 5 A a A UR 5 A 08 V A 50 A B C 5 A 5 A a A UR 65 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: In = 50A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In - Earth leakage protetion: 000mA SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C60 50A P D urve - Earth leakage protetion: C60 Vigi module ; setting to 000mA CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A 4poles / poles proteted - Thermal threshold : Ir = 6A - Magneti Threshold : Im= 5 x Ir - eutral not proteted - Earth leakage protetion: depending on the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd - Trip Unit : Mirologi 60A / Ir Setup=6A- Earth leakage protetion: Vigiompat MH or MB, setting depending on the installation TC Earthing System 08 V A 50 A B C PE 5 A 5 A a A UR 65 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: In = 50A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C60 50A P D urve AuSine SWP A Autotransformer for 08 V Mains Installation 5

10 TS Earthing System 08 V A 50 A B C 5 A 5 A a A UR 65 A PE CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A 4poles / poles proteted - Trip Unit: - Thermal threshold : Ir = 6A - Magneti Threshold : Im= 5 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd - Trip Unit : Mirologi 60A / Ir Setup=6"A 6 AuSine SWP A Autotransformer for 08 V Mains Installation

11 Connetion to AuSine SWP 0 A Terminal Blok on-distriuted neutral Distriuted neutral IT Earthing System IT Earthing System 08 V A 75 A B C 5 A a 40 A UR 5 A 08 V A 75 A B C 0 A 5 A a 40 A UR 00 A CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: In = 50A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C60 50A P - Trip Unit : D urve TT Earthing System CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: 60A 4poles / poles proteted - Trip Unit: - Thermal threshold : Ir = 6A - Magneti Threshold : Im= 5 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd - Trip Unit : Mirologi 60A / Ir Setup=6A TT Earthing System 08 V A 75 A B C 5 A a 40 A UR 5 A 08 V A 75 A B C 0 A 5 A a 40 A UR 00 A CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: In = 50A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In - Earth leakage protetion: 000mA SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C60 50A P - Trip Unit : D urve - Earth leakage protetion: C60 Vigi module ; setting to 000mA CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: 60A 4poles / poles proteted - Trip Unit: - Thermal threshold : Ir = 6A - Magneti Threshold : Im= 5 x Ir - eutral not proteted - Earth leakage protetion: depending on the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd - Trip Unit : Mirologi 60A / Ir Setup=6A - Earth leakage protetion: Vigiompat MH or MB, setting depending on the installation TC Earthing System 08 V A 75 A 5 A a 40 A UR B C PE 0 A 00 A CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: In = 50A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C60 50A P - Trip Unit : D urve AuSine SWP A Autotransformer for 08 V Mains Installation 7

12 TS Earthing System 08 V A 75 A B C 0 A 5 A a 40 A UR 00 A PE CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: 60A 4poles / poles proteted - Trip Unit: - Thermal threshold : Ir = 6A - Magneti Threshold : Im= 5 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd - Trip Unit : Mirologi 60A / Ir Setup=6"A 8 AuSine SWP A Autotransformer for 08 V Mains Installation

13 Connetion to AuSine SWP 45 A Terminal Blok on-distriuted neutral Distriuted neutral IT Earthing System IT Earthing System 08 V A 05 A B C 50 A a 6 A UR 50 A 08 V A 05 A B C 0 A 50 A a 6 A UR 50 A CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: In=00A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C0H 00A P D urve TT Earthing System CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: 400A 4poles / poles proteted - Trip Unit: - Thermal threshold : Ir = 60A - Magneti Threshold : Im= 4 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX400 4pd - Trip Unit : Mirologi 60A / Ir Setup=50A TT Earthing System 08 V A 05 A B C 50 A a 6 A UR 50 A 08 V A 05 A B C 0 A 50 A a 6 A UR 50 A CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: In=00A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In - Earth leakage protetion: 000mA SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C0H 00A P D urve - Earth leakage protetion: C0 Vigiomodule ; setting to 000mA CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: 400A 4poles / poles proteted - Trip Unit: - Thermal threshold : Ir = 60A - Magneti Threshold : Im= 4 x Ir - eutral not proteted - Earth leakage protetion: depending on the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX400 4pd Mirologi 400A / Ir setup=60a - Earth leakage protetion: Vigiompat MH or MB, setting depending on the installation TC Earthing System 08 V A 05 A 50 A a 6 A UR B C PE 0 A 50 A CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: In=00A poles - Trip Unit: Eletroni iruit protetion type: Magneti etween 0 to 4 In SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: C0H 00A P D urve TS Earthing System AuSine SWP A Autotransformer for 08 V Mains Installation 9

14 08 V A 05 A B C 0 A 50 A a 6 A UR 50 A PE CIRCUIT BREAKER SPECIFICATIOS: - Ciruit reaker range: 400A 4poles / poles proteted - Trip Unit: - Thermal threshold : Ir = 60A - Magneti Threshold : Im= 4 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX400 4pd - Trip Unit : Mirologi 400A / Ir Setup=60A 0 AuSine SWP A Autotransformer for 08 V Mains Installation

15 Connetion to AuSine SWP 60 A Terminal Blok on-distriuted neutral Distriuted neutral IT Earthing System IT Earthing System 08 V A 5 A B C 65 A a 80 A UR 65 A 08 V A 5 A B C 400 A 65 A a 80 A UR 00 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A poles / poles proteted - Thermal threshold : Ir = 50A - Magneti Threshold : Im= 4 x Ir SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 pd Mirologi 60A / Ir setup= 50A TT Earthing System CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 400A 4poles / poles proteted - Thermal threshold : Ir = 60A - Magneti Threshold : Im= 4 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX400 4pd Mirologi 400A / Ir Setup=60A TT Earthing System 08 V A 5 A B C 65 A a 80 A UR 65 A 08 V A 5 A B C 400 A 65 A a 80 A UR 00 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A poles / poles proteted - Thermal threshold : Ir = 50A - Magneti Threshold : Im= 4 x Ir SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 pd Mirologi 60A / Ir setup= 50A - Earth leakage protetion: Vigiompat MH or MB, setting: depending on the installation CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 400A 4poles / poles proteted - Thermal threshold : Ir = 60A - Magneti Threshold : Im= 4 x Ir - eutral not proteted - Earth leakage protetion: depending on the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX400 4pd Mirologi 400A / Ir Setup=60A - Earth leakage protetion: Vigiompat MH or MB, setting depending on the installation TC Earthing System 08 V A 5 A 65 A a 80 A UR B C PE 400 A 00 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A poles - Thermal threshold : Ir = 60A - Magneti Threshold : Im= 4 x Ir SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 pd Mirologi 60A / Ir setup=60a - Earth leakage protetion: Vigiompat MH or MB, setting: depending on the installation AuSine SWP A Autotransformer for 08 V Mains Installation

16 TS Earthing System 08 V A 5 A B C 400 A 65 A a 80 A UR 00 A PE CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A 4poles / poles proteted - Thermal threshold : Ir = 50A - Magneti Threshold : Im= 4 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 pd Mirologi 60A / Ir setup= 50A AuSine SWP A Autotransformer for 08 V Mains Installation

17 Connetion to AuSine SWP 90 A Terminal Blok with on-distriuted eutral on-distriuted neutral IT Earthing System 08 V A 05 A B C 00 A a 00 A 6 A UR 50 A 50 A 6 A UR 50 A 50 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 50A poles / poles proteted - Thermal threshold : Ir = 5A - Magneti Threshold : Im= 5 x Ir SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX50 pd Mirologi 50A / Ir Setup=5A TT Earthing System 08 V A 05 A B C 00 A a 00 A 6 A UR 50 A 50 A 6 A UR 50 A 50 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 50A poles / poles proteted - Thermal threshold : Ir = 5A - Magneti Threshold : Im= 5 x Ir - Earth leakage protetion: depending on the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX50 pd Mirologi 50A / Ir Setup=5A - Earth leakage protetion: Vigiompat MH or MB, setting depending on the installation AuSine SWP A Autotransformer for 08 V Mains Installation

18 Connetion to AuSine SWP 90 A Terminal Blok with Distriuted eutral IT Earthing System TC Earthing System 08 V A 05 A B 00 A a C 60 A 00 A 6 A UR 50 A 50 A 08 V A 05 A B C PE 60 A 00 A a 00 A 6 A UR 50 A 50 A 6 A UR 50 A 50 A 6 A UR 50 A 50 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A 4poles / poles proteted - Thermal threshold : Ir = 50A - Magneti Threshold : Im= 5 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd Mirologi 60A / Ir Setup=50A TT Earthing System CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 50A poles - Thermal threshold : Ir = 50A - Magneti Threshold : Im= 5 x Ir SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX50 pd Mirologi 50A / Ir setup=50a TS Earthing System 08 V A 05 A B 00 A a C 60 A 00 A 6 A UR 50 A 50 A 08 V A 05 A B 00 A a C 60 A 00 A 6 A UR 50 A 50 A PE 6 A UR 50 A 50 A 6 A UR 50 A 50 A PE CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A 4poles / poles proteted - Thermal threshold : Ir = 50A - Magneti Threshold : Im= 5 x Ir - eutral not proteted - Earth leakage protetion: depending on the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd Mirologi 60A / Ir Setup=50A - Earth leakage protetion: Vigiompat MH or MB, setting depending on the installation CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 60A 4poles / poles proteted - Thermal threshold : Ir = 50A - Magneti Threshold : Im= 5 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 4pd Mirologi 60A / Ir Setup=50A 4 AuSine SWP A Autotransformer for 08 V Mains Installation

19 Connetion to AuSine SWP 0 A Terminal Blok with on-distriuted eutral on-distriuted neutral IT Earthing System 08 V A 65 A B C 0 A a 0 A 80 A UR 65 A 65 A 80 A UR 65 A 65 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 400A poles / poles proteted - Thermal threshold : Ir = 80A - Magneti Threshold : Im= 9 x Ir SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX400 pd Mirologi 400A / Ir Setup=80A TT Earthing System 08 V A 65 A B C 0 A a 0 A 80 A UR 65 A 65 A 80 A UR 65 A 65 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 400A poles / poles proteted - Thermal threshold : Ir = 80A - Magneti Threshold : Im= 9 x Ir - Earth leakage protetion: depending on the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX400 pd Mirologi 400A / Ir Setup=80A - Earth leakage protetion: Vigiompat MH or MB, setting depending on the installation AuSine SWP A Autotransformer for 08 V Mains Installation 5

20 Connetion to AuSine SWP 0 A Terminal Blok with Distriuted eutral Distriuted neutral IT Earthing System TC Earthing System 08 V A 65 A B C 790 A 0 A a 400 A 80 A UR 65 A 00 A 08 V A 65 A B C PE 790 A 0 A a 400 A 80 A UR 65 A 00 A 80 A UR 65 A 00 A 80 A UR 65 A 00 A CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 800A 4poles / poles proteted - Thermal threshold : Ir = 0A - Magneti Threshold : Im= 4 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: S800 4pd Mirologi 800A / Ir setup= 0A TT Earthing System CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 400A poles - Thermal threshold : Ir = 80A - Magneti Threshold : Im= 9 x Ir SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: SX60 pd Mirologi 400A / Ir setup=80a TS Earthing System 08 V A 65 A B C 790 A 0 A a 400 A 80 A UR 65 A 00 A 08 V A 65 A B C 0 A 790 A 400 A 80 A UR 65 A 00 A PE 80 A UR 65 A 80 A UR 65 A 00 A 00 A PE CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 800A 4poles / poles proteted - Thermal threshold : Ir = 0A - Magneti Threshold : Im= 4 x Ir - eutral not proteted Earth protetion : to add a tore with relay and trip auxiliary oil / setup depending of the installation SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: S800 4pd Mirologi 800A / Ir setup= 0A Earth protetion : to add Vigirex relay + tore + MX - setup depending of the installation CIRCUIT BREAKER SPECIFICATIOS: Ciruit reaker range: 800A 4poles / poles proteted - Thermal threshold : Ir = 0A - Magneti Threshold : Im= 4 x Ir - eutral not proteted SCHEIDER ELECTRIC RECOMMEDATIOS: Ciruit reaker: S800 4pd Mirologi 800A / Ir setup= 0A 6 AuSine SWP A Autotransformer for 08 V Mains Installation

21 Cales The ross-setional areas of the ales should e determined in ompliane with appliale standards using the information in the tale elow and the tales indiating the reommended protetive devies for the various AuSine SWP ratings. If the neutral is distriuted, it should e sized to take into aount the predominant presene of the rd harmoni that an lead to a urrent in the neutral three times that of the urrent in the phases. ote: The minimum ale ross-setional area an e determined from the sizing urrent (Is) given the tales elow. ote: If the neutral is distriuted, it should e onneted. Rating (A) Reommended ross-setional areas of ales (mm) Maximum length of power ales (m) Primary (08 V) Seondary (400 V) Primary (08 V) Phases eutral Phases eutral x x0 0 per uile 50 per uile x95 6 per uile 70 per uile 0 0 Seondary (400 V) AuSine SWP A Autotransformer for 08 V Mains Installation 7

22 Power Connetions Terminal Blok a-- seondary 400 V A B C primary 08 V A B C primary 0 V A B C primary 40 V Top View of Autotransformer Terminal Blok a A A A B B B C C C Primary and Seondary Connetions Rating A B C a 0 0 A M6 terminals A AI 5x ø7 terminals 90 0 A AI 0x5 ø9 terminals Connetion of Exposed Condutive Parts and the eutral Common to Primary and Seondary Rating Exposed Condutive Parts 0 0 A M6 terminals M6 terminals A AI 5x ø7 terminals M8 terminals 90 0 A AI 0x5 ø9 terminals M0 terminals 8 AuSine SWP A Autotransformer for 08 V Mains Installation

23 Single Line Diagrams The autotransformer must e onneted etween the mains and the AuSine SWP Ative Filter. ote: The position of the sensors and the onnetion point of the AuSine SWP Ative Filter may vary from one installation to another depending on the type of prolem to e solved. The optimum loations are determined from the information gathered during the assessment arried out on the site efore installation. ote: The autotransformer and the AuSine SWP are onneted in parallel with the load. ote: The AuSine SWP Ative Filter must e powered y a speial iruit. The autotransformer should e proteted y a iruit reaker and the line supplying the AuSine SWP y fuses. The AuSine SWP uses this line to send harmonis intended to ompensate the load harmonis ak into the mains. Eah power iruit remains independent and has its own protetive devie (not supplied). It is possile to onnet up to 4 ative filters in parallel to ompensate a given load or group of loads AuSine SWP A Autotransformer for 08 V Mains Installation 9

24 Example of 0 A, 0 A, 45 A or 60 A Ative Harmoni Filter A 08 V mains supply F Load to e ompensated B Low voltage distriution swithoard G Autotransformer C Ciruit reaker H Fuses D Current sensor I Harmoni ompensating urrent E Harmoni urrent to e ompensated 0 AuSine SWP A Autotransformer for 08 V Mains Installation

25 Example of 90 A or 0 A Ative Harmoni Filter A 08 V mains supply F Load to e ompensated B Low voltage distriution swithoard G Autotransformer C Ciruit reaker H Fuses D Current sensor I Harmoni ompensating urrents E Harmoni urrent to e ompensated AuSine SWP A Autotransformer for 08 V Mains Installation

26 Example of Two 0 A, 0 A, 45 A or 60 A Ative Harmoni Filters in Parallel A 08 V mains supply F Load to e ompensated B Low voltage distriution swithoard G Autotransformer C Ciruit reaker H Fuses D Current sensor I Harmoni ompensating urrent E Harmoni urrent to e ompensated AuSine SWP A Autotransformer for 08 V Mains Installation

27 Example of Two 90 A or 0 A Ative Harmoni Filters in Parallel A 08 V mains supply F Load to e ompensated B Low voltage distriution swithoard G Autotransformer C Ciruit reaker H Fuses D Current sensor I Harmoni ompensating urrent E Harmoni urrent to e ompensated AuSine SWP A Autotransformer for 08 V Mains Installation

28 Connet Autotransformer WARIG: Connetion operations must e arried out with the equipment de-energized. For the protetion of persons, always onnet the PE or PE ondutor first. ote: AuSine SWP is suitale for all types of earthing arrangements.. Make sure that the iruit reaker on the iruit supplying the AuSine SWP unit is in the OFF position ( O ).. Connet the PE or PE ondutor first.. Connet the other ondutors, taking are to respet the phase rotation diretion. WARIG: The onneting ales must e mehanially seured near the terminal lok to prevent any mehanial fores from eing exerted on the onnetions. ote: If the ales are pulled, the PE or PE onnetion should e the last to e sujeted to the applied fore. ote: To avoid interferene, ontrol wires onneted to the AuSine SWP unit (onnetions with urrent sensors, ommuniation ales, relay ontat wiring) should never e run near the power ales or the autotransformer. For the same reason, the power ales onneted to the AuSine SWP Ative Filter or the autotransformer should not e run near other power ales. 4 AuSine SWP A Autotransformer for 08 V Mains Installation

29 AuSine SWP A Autotransformer for 08 V Mains Installation 5

30 Worldwide Customer Support Customer support is availale at no harge via or telephone. Contat information is availale at eletri.om. Shneider Eletri. AuSine is a registered trademark of Shneider Eletri. All other trademarks are property of the respetive owners August 0