ISO 9001:2000 SIA C. Dual Power Overcurrent Protection Relay INSTALLATION GUIDE. Guia_SIA-C_Rev / 32

Transcription

1 ISO 9001:2000 SIA Dual Power Overcurrent Protection Relay INSTALLATION GUIDE Guia_SIA-_Rev / 32

2 1.USER INTERFAE Revision A Revision B and Bistable magnetic indicators LED Indicators RS232 ommunication port LD and keypad SIom ommunications program Setting-up the session: Password and access levels FUNTIONAL DIAGRAM DIMENSIONS UTOUT PATTERN AND ONNETION DIAGRAMS Revision A utout mm Revision B utout mm onnection diagrams onnection diagrams. Three phase Ts and sensitive neutral: onnection diagrams. Three phase Ts and solid neutral: onnection diagrams. Three phase Ts for measuring and three phase Ts for supply and 1 T for sensitive neutral: onnection diagrams. Three phase Ts for measuring and three phase Ts for supply and solid neutral: Terminals Revision A Revision B and MODEL LIST PROTETION FUNTIONS AND SETTINGS Protections functions Function 50P. Phase instantaneous overcurrent Function 51P. Inverse time phase overcurrent Function 50N. Neutral instantaneous overcurrent Function 51N. Inverse time neutral overcurrent External trip Trip Bus Equipment settings urves IE255-4/BS Monitoring and control States and Events Self-diagnosis Date-time synchronisation ommunication Test program Guia_SIA-_Rev / 32

3 7.TEHNIAL SPEIFIATIONS AND STANDARDS Technical specifications FLOWHART Guia_SIA-_Rev / 32

4 1. USER INTERFAE 1.1. Revision A Leds LD (2x20 characters) Magnetic bistables Bistables reset Events erase Keypad RS Revision B and Revision B: 1 bistable Revision : 3 bistables LD (2x20 characters) Leds Magnetic bistables Keypad Bistables reset Events erase RS232 Guia_SIA-_Rev / 32

5 1.3. Bistable magnetic indicators The front panel is equipped with 3 bistable magnetic indicators which indicate the cause of the last trip. The indicators remain in position even when the equipment looses power, so that the maintenance service can see the cause of the trip even through the equipment is not powered. Once they have been activated, it is necessary to manually reset them by pressing the RESET button. The operation of the magnetic indicators can be checked from the test menu. Magnetic indicator 50P/51P activated Magnetic indicator 50/51N activated External trip magnetic indicator A trip has been caused by phase instantaneous overcurrent or phase inverse time overcurrent A trip has been caused by neutral instantaneous overcurrent or neutral inverse time overcurrent A trip has been caused by the activation of the direct trip input 1.4. LED Indicators The SIA- front panel has three LED pilot lights to show the type of power being used: self-power, battery or auxiliary power. The LEDs are switched off when the power type that they represent is not active, and they blink when the power type that they represent is active. Aside from showing the type of power that is being used by the equipment, one of the LEDs should be blinking under normal conditions. If they are all switched off, or some or all of them are permanently lit, this means that the equipment is not operational. Vaux LED Self-power LED Battery LED Activated (LED blinking) if it detects the auxiliary voltage Activated (LED blinking) if it detects the self-power current Activated (LED blinking) if it detects voltage from an external battery More than one type of power can be used simultaneously, and more than one LED can be activated as a result. The operation of the LED indicators can be checked from the test menu RS232 ommunication port The RS232 port can be found on the lower part of the front panel. The battery can be connected to this port through its kit, allowing the equipment to communicate with a local P and to be powered at the same time. P communication through the RS232 allows all the information and the settings parameters to be accessed LD and keypad The front of the SIA- relay is fitted with an alphanumeric LD screen, measuring 2x20. This screen provides the user with access to read information about the settings parameters, measurements, status and events. All of this information is arranged in a system of menus. Guia_SIA-_Rev / 32

6 A keypad is fitted to the relay front panel, which can be used to access the information shown on the LD screen and to navigate through the menu system. This membrane keyboard has 6 keys that can be used to navigate through the different menus and to change the setting parameters. The and keys can be used to navigate through the different menus, the different options in each menu and the different values for the settings parameters. The OK key is used to access the menus and the different options, as well as to approve changes to values. The key is used to delete and to go back through the menu levels. As well as the 6 keys, there is also a "Reset" key. When Reset is pressed, the bistable magnetic indicators return to their initial position. The Reset key can also be used to delete all of the events in the "Events" menu SIom ommunications program The SIcom program, which works with the Windows 2000/XP operating system is provided, and can be used to gain access to all of the equipment information, to modify the settings and to save events using a graphic user interface. The following operations can be carried out using the SIcom program: Status reading Measurement reading Reading and changing settings Reading and deleting events hanging the user passwords Loading settings files Date-time synchronisation hecking the versions of the equipment onfiguring the modbus address 1.8. Setting-up the session: Password and access levels Users must identify themselves with a password in order to start communications and to change the equipment settings or configuration using the HMI. Depending on the access level, it may or may not be possible to perform the operations shown on the table below. AESS LEVEL Read-only permission: Status and measurements Settings Permission to: hange settings Download and Delete the Events buffer Permission to: Execute ommands Permission to: hange onfiguration Permission to hange Protected Settings Events 1 YES YES NO NO YES 2 YES YES NO NO NO 3 YES NO YES NO NO 4 YES YES YES NO NO 5 YES YES YES YES NO Guia_SIA-_Rev / 32

7 Four passwords and their associated levels of access are set up when the equipment is configured using the SIcom program. By default, the equipment is programmed with the following passwords and their associated levels: PASSWORD AESS LEVEL The SIA- does not have a command feature. The SIA- does not have a protected settings feature. Guia_SIA-_Rev / 32

8 2. FUNTIONAL DIAGRAM 3. DIMENSIONS Guia_SIA-_Rev / 32

9 4. UTOUT PATTERN AND ONNETION DIAGRAMS 4.1. Revision A utout mm Frontal view 4.2. Revision B utout mm Frontal view Guia_SIA-_Rev / 32

10 4.3. onnection diagrams onnection diagrams. Three phase Ts and sensitive neutral: Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts Supply and measure 1 Sensitive neutral T Striker 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts Supply and measure 1 Sensitive neutral T AT + TM 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts Supply and measure 1 Sensitive neutral T AT 230Vac (by model) 24 Vdc (by model) Guia_SIA-_Rev / 32

11 onnection diagrams. Three phase Ts and solid neutral: Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts Supply and measure Solid neutral Striker 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts Supply and measure Solid neutral AT + TM 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts Supply and measure Solid neutral AT 230Vac (by model) 24 Vdc (by model) Guia_SIA-_Rev / 32

12 onnection diagrams. Three phase Ts for measuring and three phase Ts for supply and 1 T for sensitive neutral: Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts for supply 3 Ts for measure 1 Sensitive neutral T Striker 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Disparo Power Supply Optional Power Supply 3 Ts for supply 3 Ts for measure 1 Sensitive neutral T AT + TM 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Disparo Power Supply Optional Power Supply 3 Ts for supply 3 Ts for measure 1 Sensitive neutral T AT 230Vac (by model) 24 Vdc (by model) Guia_SIA-_Rev / 32

13 onnection diagrams. Three phase Ts for measuring and three phase Ts for supply and solid neutral: Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts for supply 3 Ts for measure Solid neutral Striker 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts for supply 3 Ts for measure Solid neutral AT + TM 230Vac (by model) 24 Vdc (by model) Phase Ts Neutral mode Trip Power Supply Optional Power Supply 3 Ts for supply 3 Ts for measure Solid neutral AT 230Vac (by model) 24 Vdc (by model) Guia_SIA-_Rev / 32

14 4.4. Bornas Revision A Revision B and Guia_SIA-_Rev / 32

15 A1 Phase A current input for measurement D5 Positive for the inputs A2 Phase A current output for measurement D6 Digital input 1 A3 Phase B current input for measurement D7 Digital input 2 A4 Phase B current output for measurement D8 ommon digital input A5 Phase current input for measurement D9 Ground A6 Phase current output for measurement D10 Digital output 1 N A7 Neutral current input for measurement D11 Digital 1 common output A8 Neutral current output for measurement D12 Digital output 1 NA B1 Phase A current input for power supply D13 Digital output 2 N B2 Phase A current output for power supply D14 Digital 2 common output B3 Phase B current input for power supply D15 Digital output 2 NA B4 Phase B current output for power supply D16 Trip output positive / AT free potential output B5 Phase current input for power supply D17 Trip output gnd / AT free potential output B6 Phase current output for power supply D18 RS485 ground D1 Auxiliary Voltage - D19 RS485 B - D2 Auxiliary Voltage + D20 RS485 A + D3-D4 External trip Earthing screw Guia_SIA-_Rev / 32

16 5. MODEL LIST TYPE PHASE MEASUREMENT NEUTRAL MEASUREMENT NETWORK FREQUENY POWER SUPPLY EXTRA FUNTIONS OMMUNIATIONS INPUTS/OUTPUTS PROESSORS AND MEMORY LANGUAGE REVISION 50P+51P+50N+51N A 5 A A 5 A Hz 60 Hz Vdc + Selfpowered 12 Vdc + Selfpowered Vac 12 Vdc + Selfpowered Vac 12 Vdc + Selfpowered + 24 Vdc With striker and without external trip With striker and with external trip With potential free contact and without external trip With potential free contact and with external trip 0 1 ModBus Local (RS 232). ModBus Local (RS 232) y Scada (485) Without inputs/outputs Signalling outputs Trip bus Without non volátil RAM memory With non volátil RAM memory With non volátil RAM memory and fast startup A B English, Spanish and French English, Spanish, French and Turkish English, Spanish, French and Polish A B Vertical Assembly Horizontal assembly with 1 FLAG bistable Horizontal assembly with 3 FLAG bistables Guia_SIA-_Rev / 32

17 6. PROTETION FUNTIONS AND SETTINGS 6.1. Protections functions Function 50P. Phase instantaneous overcurrent Function Description Minimum Maximum Step Unit Default 50P Phase instantaneour overcurrent Permission - - Yes/No - No Tap 0,10 30,00 0,01 Inominal 5,00 Operating time 0,02 300,0 0,01 s 0, Function 51P. Inverse time phase overcurrent Function Description Minimum Maximum Step Unit Default 51P Inverse time phase overcurrent Permission - - Yes/No - No urve - - (1*) - Extremely inverse Dial 0,05 1,25 0,01-1,25 Tap 0,10 7,00 0,01 I nominal 1,00 Operating time 0,02 300,0 0,01 s 0,02 (1*) Inverse, Very inverse, Extremely inverse, Defined time Function 50N. Neutral instantaneous overcurrent. Function Description Minimum Maximum Step Unit Default 50N Neutral instantaneous overcurrent Permission - - Yes/No - No Tap 0,10 30,00 0,01 I nominal 1,00 Operating time 0,02 300,0 0,01 s 0,02 Guia_SIA-_Rev / 32

18 Function 51N. Inverse time neutral overcurrent. Function Description Minimum Maximum Step Unit Default 51N Inverse time neutral overcurent Permission - - Yes/No - No urve - - (1*) - Extremely inverse Dial 0,05 1,25 0,01-1,25 Tap 0,10 7,00 0,01 I nominal 0,50 Operating time 0,02 300,0 0,01 s 0,02 (1*) Inverse, Very inverse, Extremely inverse, Defined time External trip The equipment has a direct trip input, normally connected to a bimetallic contact fitted to the power transformer. This serves as a backup to the overcurrent functions. The input is operational from 0.3 times the secondary rated current in case of single phase, allowing connecting a potential-free bimetallic contact which, when closed, activates the input. This input is especially protected against magnetic noise Trip Bus Function 68 allows the creation of a coordinated net of equipments installed in different levels of the line which enables the blocking or the tripping and whose objective is clearing the fault in the least damaging place of the application. phase blocking input ground blocking input SIA- supply phase pickup phase pickup ground pickup SIA- feeder a ground pickup SIA- feeder b Guia_SIA-_Rev / 32

19 Function Description Minimum Maximum Step Unit Default TRIP BUS Trip Bus Aplication - - (1*) - No activated Permission trip bus 50P - - Yes/No - Yes Permission trip bus 51P - - Yes/No - Yes Permission trip bus 50N - - Yes/No - Yes Permission trip bus 51N - - Yes/No - Yes Phase blocking time ,01 s 0 Neutral blocking time ,01 s 0 Phase blocking signalling time ,01 s 0 Neutral blocking signalling time ,01 s 0 (1*) No activated, Feeder, Supply, Feeder and Supply Equipment settings The SIA- settings are listed below: Group Description Minimum Maximum Step Unit Default Generales Equipment identifier enter your text TI phase ratio TI neutral ratio Frequency /50 Hz 50 Language ENGLISH urves IE255-4/BS142 The SIA- relay complies with the curves shown in standard IE255-4/BS-142: Inverse urve Very Inverse urve Extremely Inverse urve There is a general mathematical equation that defines the time in seconds as a function of the current: Guia_SIA-_Rev / 32

20 Guia_SIA-_Rev / 32

21 6.2. Monitoring and control States and Events Group State ause Associated Event Phase inverse time overcurrent 51P 51P Phase A pick-up Activation/Deactivation Phase A current 51P Phase B pick-up Activation/Deactivation Phase B current 51P Phase pick-up Activation/Deactivation Phase current 51P Pick-up Activation/Deactivation - 51P A Trip Activation/Deactivation Phase A current 51P B Trip Activation/Deactivation Phase B current 51P Trip Activation/Deactivation Phase current 51P Trip Activation - Instantaneous phase overcurrent 50P 50P Phase A pick-up Activation/Deactivation Phase A current 50P Phase B pick-up Activation/Deactivation Phase B current 50P Phase pick-up t Activation/Deactivation Phase current 50P Pick-up Activation/Deactivation - 50P A Trip Activation/Deactivation Phase A current 50P B Trip Activation/Deactivation Phase B current 50P Trip Activation/Deactivation Phase current 50P Trip Activation - Neutral inverse time overcurrent 51N 51N Pick-up Activation/Deactivation Neutral current 51N Trip Activation Neutral current Instantaneous neutral overcurrent 50N 50N Pick-up Activation/Deactivation Neutral current 50N Trip Activation Neutral current Trip Bus Blocking 50P Activation/Deactivation - Blocking 51P Activation/Deactivation - Blocking 50N Activation/Deactivation - Blocking 51N Activation/Deactivation - Guia_SIA-_Rev / 32

22 Blocking signalling 50P Activation/Deactivation - Blocking signalling 51P Activation/Deactivation - Blocking signalling 50N Activation/Deactivation - Blocking signalling 51N Activation/Deactivation - Generals Trip Activation/Deactivation The maximum phase current between the activation of the trip and the deactivation of the event. External trip Activation/Deactivation - Trip circuit error Activation/Deactivation - Measurement error Activation/Deactivation - Protection error Activation/Deactivation - hange of settings Activation/Deactivation - Date-time adjustment Activation/Deactivation - Local communication Activation/Deactivation - Eeprom by default Activation/Deactivation - Eeprom Error Activation/Deactivation - Eeprom change Activation/Deactivation - Events error Activation/Deactivation - Auxiliary power Activation/Deactivation - Self power Activation/Deactivation - Battery power Activation/Deactivation - Equipment start Activation/Deactivation - Outputs Output 1 Activation/Deactivation - Output 2 Activation/Deactivation - Local communication Local communication - - HMI Activity Guia_SIA-_Rev / 32

23 Self-diagnosis Diagnostic algorithms are run while the equipment is being started up and continuously when the relay is operating. This diagnostic is a preventative process to guarantee that the equipment is in good operational condition. As general considerations, we should point the following: The communications between different processors are confirmed by the corresponding integrity checking. In continuous anomalies occur, the equipment will be reset. Data related to set values are confirmed by the corresponding checking. Also, all tables showing set values are doubled, and the relay will have the capability of operating with a damaged table, but not with two damaged tables. There is a WatchDog mechanism both between and in main PUs. If any PU goes out of operation the equipment will be reset and this condition will be identified as an event. The following status bits are associated with this process: Trip circuit error Measurement error Protection error Eeprom Error Events Error Problem in the trip circuit Problem in the measurement block Problem in the protection block Problem in the eeprom memory, default settings Error in the events register On the other hand, Default settings means that the equipment is operating under factory settings, being all protection functions disabled Date-time synchronisation The SIA- relay has a real time clock (RT) in all its models, which can be synchronized from the hmi or communications. The RT maintains the updated date for at least 72 hours even without any power supply. harging time of RT capacitor is 10 minutes. The clock can be synchronized by means of any of the two following procedures: From the HMI. In this case the date and time can be entered via the keyboard. The relay will store the new event indicating that it has been synchronized. Protocol. The behaviour is identical to the HMI. The relay will synchronize the date and time, and a new synchronization event is carried out ommunication The SIA- relay can communicate with a local computer through its front RS232 port, or through a remote SADA system through the rear RS485 port. The rear RS485 port is optional and must be specified on the list of models. The ports RS232 and RS485 are switched. The RS232 port has preference. When started, the equipment is switched to remote communication (RS485) provided no key in the HMI is pressed or no local communication (RS232) is tried Test program The SIA- equipment has a test menu that can be used to check the operation of the signalling components (LEDs and magnetic indicators), along with the trip output and the signalling outputs. This check is operative regardless of the type of power that is used. Guia_SIA-_Rev / 32

24 This means that the trip circuit and the signalling outputs can be tested with just a simple battery or a 12V battery in a facility without electricity supply. The following table shows the components that can be tested, along with their status depending on whether they are activated or deactivated: Vaux power LED Self-power LED Battery LED 50/51P magnetic indicator 50/51N magnetic indicator External trip magnetic indicator Trip output (*) Signalling output 1 Signalling output 2 Deactivated Activated Deactivated Activated Deactivated Activated Deactivated Activated Deactivated Activated Deactivated Activated Deactivated Activated Deactivated Activated Deactivated Activated Vaux LED off Vaux LED blinking Self-power LED off Self-power LED blinking Battery LED off Battery LED blinking 50/51P magnetic indicator deactivated (black) 50/51P magnetic indicator activated (orange) 50/51N magnetic indicator deactivated (black) 50/51N magnetic indicator activated (orange) External trip magnetic indicator deactivated (black) External trip magnetic indicator activated (orange) Trip output deactivated Trip output activated Output 1 deactivated Output 1 activated Output 2 deactivated Output 2 activated (*) When self-power values are low or the battery is at the limit of its capacity, it is possible that the equipment may initialise. This is completely normal. The following key sequence is used to gain access to the test menu: from the main menu, press the keys,, and in sequence and then press and hold the "OK" key until the "Test menu" appears on the display. The test menu is accessed by pressing the "OK" key again, and the and keys can be used to navigate through the different menu items. Each item can be activated or deactivated by pressing "OK" on it (if the item is deactivated, it is activated by pressing OK; if the item is activated, it is deactivated by pressing OK ). Press the key to exit the test menu. To obtain more detailed information, the method for navigating the menus is explained graphically in the keypad and display section. Guia_SIA-_Rev / 32

25 7. TEHNIAL SPEIFIATIONS AND STANDARDS 7.1. Technical specifications External trip input harge level of 0,3 xin in single-phase Striker Trip output 24 Vdc 576 mj Activates the striker of the coil with the TM Potential Free trip output 250 Vac 8A 30 Vdc 8A Resisitive load (cos φ = 1) Activates the coil Signalling outputs Signalling inputs Frequency urrent measure 220 Vdc 1 A (30 W max) 250 Vac 1 A (62,5 VA max) Resisitive load (cos φ = 1) 5-24 Vdc 0,25 VA 50/60Hz RMS Sampling: 16 samples/cycle Accuracy ±2% in Inominal current ± 20%, and ±5% in the rest of the range ommunication RS232 port: Modbus RTU RS485port: Modbus RTU Auxiliary supply 230 Vca, ±20 % 110 Vca, ±20 % 24 Vcc Battery supply With adapter (Kitcom) port DB9 Self-power from current One phase self-power level: I > 0,2 x In Environment Operating temperature: -10 to 60º Storage temperature: -20 to 70 º Humidity: 95% Transformers Power supply and measurement T /5 or /1 Mechanical features Metallic box Panel Mounting 1/3 Rack 4 U IP-52 Guia_SIA-_Rev / 32

26 ISO 9001: FLOWHART OK OK hold Enter lower submenu Back upper submenu Navigate inside menu Direct access Direct access Enter numerical value Sequence for VERSIONS Sequence for TEST MENU SIA AA OK MEASUREMENTS States 1/4 OK IA = 0.00 A 2/4 IB = 0.00 A 3/4 I = 0.00 A 4/4 IO = 0.00 A States 50P OK OK Phase A Pickup: Phase B Pickup: Phase Pickup: Phase Pickup: Phase A Trip: Phase B Trip: Guia_SIA-_Rev / 32

27 Phase Trip: Phase Trip: States 51P OK Phase A Pickup: Phase B Pickup: Phase Pickup: Phase Pickup: Phase A Trip: Phase B Trip: Phase Trip: Phase Trip: States 50N OK Ground Pickup: Ground Trip: States 51N OK Ground Pickup: Ground Trip: States GNAL >Activated OK Trip: External Trip: Guia_SIA-_Rev / 32

28 SETTINGS GEN TripPower error: 50 Hz: <<ATIVATED>> Mag.M. error: Measure error: Ready: <<ATIVATED>> Protecti error: Setting change: Set Date/Time: Telecontrol NO: <<ATIVATED>> FactorySetting: Eeprom error: Eeprom changed: Event error: States OUTPUTS OK Output 1: Output 2: States LOAL >Activated OK Local OM.: MMI Activity: <<ATIVATED>> Guia_SIA-_Rev / 32

29 Settings 50P OK Function Enable NO OK OK urrent Tap: 5.00 xin(1.00) Time Delay 0.02 s Set Password -> 0 Set Password -> 5555 OK Function Enable NO -> NO Settings 51P Function Enable NO -> YES Function Enable NO OK OK urve type: ExtrInv Time Dial: 1.25 urrent Tap: 1.00 xin(1.00) Time Delay 0.02 s Function Enable NO > YES y/n SETTING HANGED OK Function Enable Function Enable OK YES Settings 50N OK Function Enable NO urrent Tap: 1.00 xin(1.00) Time Delay 0.02 s Settings 51N OK Function Enable NO urve type: ExtrInv Time Dial: 1.25 urrent Tap: 0.50 xin(1.00) Time Delay 0.02 s Set Password OK -> 0 Set Password -> 5555 Time Dial OK > 0 Guia_SIA-_Rev / 32

30 Identification enter your text T Phase Ratio 1 T Neutro Ratio 1 Frequency 50 Hz Language ENGLISH Time Dial > 0.5 Time Dial OK 1.25 > 0.5 y/n SETTING HANGED OK Time Dial Time Dial: OK 0.50 EVENTS There are 1 01/01/00 01:00:05675 OK Events erased 1/1: 0 OK Events erased DATE AND TIME 01/01/ :43:25 OK 01/01/ :43 Vers: OM DSP PI OK TEST MENU y/n? without protection! hold Set Password OK -> 0 Set Password -> 5555 OK TEST MENU V. aux Led: OK V. aux Led: OK OK <<ATIVATED>> self-power Led: self-power Led: OK OK <<ATIVATED>> battery Led: Guia_SIA-_Rev / 32

31 battery Led: OK OK <<ATIVATED>> 50P/51P bistable: 50P/51P bistable: OK OK <<ATIVATED>> 50N/51N bistable: 50N/51N bistable: OK OK <<ATIVATED>> ext trip bistable: ext trip bistable: OK OK <<ATIVATED>> Trip ontact: Trip ontact: OK OK <<ATIVATED>> Output 1: Output 1: OK OK <<ATIVATED>> Output 2: Output 2: OK OK <<ATIVATED>> Guia_SIA-_Rev / 32

32 FANOX ELETRONI S.L. Parque Tecnológico de Bizkaia Astondo bidea, Edif DERIO ESPAÑA Tel Fax power-td@fanox.com Guia_SIA-_Rev / 32