Digital Temperature Controllers/Digital Controllers

Transcription

1 Digital Temperature Controllers/Digital Controllers Upgraded /6, /8, and /4 DIN Controllers, the Best-selling Series. Basi Type (Renewal and Advaned Type (New Improved indiation auray and preventive maintenane (Basi Type New high-performane Controllers (Advaned Type Easy-to-use one-touh operation with PF Key (Only for /8 and /4 DIN). Logi operations. Series Basi Type (Renewal Advaned Type (New E5EN E5AN -H E5EN-H E5AN-H /6 DIN /8 DIN /4 DIN /6 DIN /8 DIN /4 DIN

2 Contents Digital Temperature Controllers /-U... 3 E5AN/E5EN... 7 Digital Controllers -H... 3 E5AN-H/E5EN-H Operation Proedure Operation Common to All Controllers Safety Preautions C-Thermo Support Software EST2-2C-V

3 Basi-type Digital Temperature Controller /-U (48 x 48 mm) New 48 x 48-mm Basi Temperature Controller with Enhaned Funtions and Performane. Improved Indiation Auray and Preventive aintenane Funtion. Indiation Auray Thermoouple : ±.3% of PV (previous models: ±.5%) Pt : ±.2% of PV (previous models: ±.5%) Analog : ±.2% FS (previous models: ±.5%) New -U odels (Plug-in odels) with analog s and urrent s. A PV/SV-status display funtion an be set to automatially alternate between displaying the status of the Temperature Controller (auto/manual, RUN/STOP, and alarms) and the PV or SV. Preventive maintenane for relays in the Temperature Controller using a Control Output / Counter mm mm -U Refer to Safety Preautions on page 66. -U (48 x 48 mm) -H (48 x 48 mm) ain I/O Funtions Event Inputs None Two Sensor Inputs Universal thermoouple/pt s (odels with temperature s) Analog urrent/voltage s (odels with analog s) Indiation Auray Thermoouple : ±.3% of PV Pt : ±.2% of PV Analog : ±.2% FS Sampling Period 25 ms Control Output 2 None 2-level Display: PV and SV Control Output Long-life relay (hybrid) Auxiliary Outputs None One Two 4-digit Display Auto/manual swithing Temperature Controller status display Simple program funtion Control / ount alarm PV hange rate alarm odels also available with RS-485 ommuniations Operation This data sheet is provided as a guideline for seleting produts. Be sure to refer to the following user manuals for appliation preautions and other information required for operation before attempting to use the produt. /E5AN/E5EN Digital Temperature Controllers User's anual Basi Type (Cat. No. H56) /E5AN/E5EN Digital Temperature Controllers anual Basi Type (Cat. No. H58) Safety Preautions 3

4 /-U Lineup -U (48 x 48 mm) Terminal blok Temperature ontrol 2 ontrol s ontrol or 2 auxiliary s 2 auxiliary s or 2 auxiliary s Basi Type Analog 2 ontrol s 2 auxiliary s -H (48 x 48 mm) Note: odels with one ontrol and one or two auxiliary s and models with two ontrol s an be used for heating/ooling ontrol. odel Number Struture odel Number Legend Controllers -@@@@-@ Control Output R: Q: C: Y: Long-life relay (hybrid) 2. Auxiliary Outputs 2 Blank: None 2: Two s 3. Option : Option Unit an be mounted. 4. Input Type T: Universal thermoouple/platinum resistane thermometer L: Analog urrent/voltage 5. Power Supply Voltage Blank: to 24 VAC D: 24 VAC/VDC 6. Case Color Blank: Blak W: Silver 7. Terminal Cover -5: With terminal over Plug-in Temperature Analog Option Units E53-CN@@@ Appliable Controller CN: or -H ontrol ontrol 2. Funtion Blank: None Q: Control 2 (voltage for driving SSR) P: Power supply for sensor,, or 2 auxiliary s,, or 2 auxiliary s 3. Funtion 2 Blank: None H: Heater burnout/ssr failure/heater overurrent detetion (CT) HH: Heater burnout/ssr failure/heater overurrent detetion (CT2) B: Two event s 3: RS-485 ommuniations H3: Heater burnout/ssr failure/heater overurrent detetion (CT) + RS-485 ommuniations HB: Heater burnout/ssr failure/heater overurrent detetion (CT) + Two event s HH3: Heater burnout/ssr failure/heater overurrent detetion (CT2) + RS-485 ommuniations 4. Version N2: Appliable only to models released after January 28 Note: Not all ombinations of funtion and funtion 2 speifiations are possible for Option Units (E53-@@@@).. Always onnet an AC load to a long-life relay. The will not turn if a DC load is onneted beause a tria is used for swithing the iruit. For details, hek the onditions in Ratings. 2. Auxiliary s are ontat s that an be used to alarms or results of logi operations. 4

5 Ordering Information Controllers with Terminal Bloks Size /6 DIN (W H D) Case olor Blak Power supply voltage to 24 VAC 24 VAC/VDC Option Units One of the following Option Units an be mounted to provide the with additional funtions. RS-485 RS-485 RS-485 RS-485 RS-485 Silver Note: Option Units annot be used for plug-in models. These Option Units are appliable only to models released after January 28. /-U Input type Auxiliary s Control odel Thermoouple or Resistane thermometer Thermoouple or Resistane thermometer to 24 VAC Analog (urrent/voltage) 24 VAC/VDC to 24 VAC Analog (urrent/voltage) Thermoouple or Resistane thermometer 24 VAC/VDC 2 3-phase heater burnout/ssr failure/ Heater overurrent detetion Heater burnout/ssr failure/heater overurrent detetion Heater burnout/ssr failure/heater overurrent detetion Heater burnout/ssr failure/heater overurrent detetion Heater burnout/ssr failure/heater overurrent detetion 3-phase heater burnout/ssr failure/ Heater overurrent detetion None 2 None 2 None 2 2 None 2 Funtions Event s Event s Event s Event s Control 2 (Voltage for driving SSR) Control 2 (Voltage for driving SSR) Control 2 (Voltage for driving SSR) Control 2 (Voltage for driving SSR) Long-life relay (hybrid) Long-life relay (hybrid) Long-life relay (hybrid) External power supply for ESB External power supply for ESB External power supply for ESB -RT-5 -QT-5 -CT-5 -R2T-5 -Q2T-5 -C2T-5 -Y2T-5 -RTD-5 -QTD-5 -CTD-5 -R2TD-5 -Q2TD-5 -C2TD-5 -RL-5 -QL-5 -CL-5 -R2L-5 -Q2L-5 -C2L-5 -Y2L-5 -R2LD-5 -Q2LD-5 -C2LD-5 -RT-W-5 -QT-W-5 -CT-W-5 -R2T-W-5 -Q2T-W-5 -C2T-W-5 -Y2T-W-5 -R2TD-W-5 -Q2TD-W-5 -C2TD-W-5 odel E53-CNHH3N2 E53-CNHBN2 E53-CNQ3N2 E53-CNPBN2 E53-CNPHN2 E53-CNP3N2 E53-CNH3N2 E53-CN3N2 E53-CNBN2 E53-CNQHN2 E53-CNQHHN2 E53-CNQBN2 -U (48 x 48 mm) -H (48 x 48 mm) Operation Safety Preautions 5

6 -U (48 x 48 mm) -H (48 x 48 mm) /-U odel Number Struture odel Number Legend (Plug-in-type Controllers) -@@@U Output Type R: Q: C: 2. Number of Alarms Blank: No alarm : One alarm 2: Two alarms Ordering Information Plug-in-type Controllers 3. Input Type T: Universal thermoouple/platinum resistane thermometer L: Analog Input 4. Plug-in type U: Plug-in type Size Case olor Power supply voltage Input type Auxiliary s Control odel /6 DIN Blak to 24 VAC 24 VAC/VDC Thermoouple or resistane thermometer Analog (urrent/voltage) Thermoouple or resistane thermometer None 2 2 None 2 -RTU -QTU -CTU -RTU -QTU -CTU -R2TU -Q2TU -C2TU -RLU -QLU -CLU -R2LU -Q2LU -C2LU -RTDU -QTDU -CTDU -RTDU -QTDU -CTDU -R2TDU -Q2TDU -C2TDU 6

7 /-U Aessories (Order Separately) USB-Serial Conversion Cable Terminal Cover Connetable models odel odel E58-CIFQ Note: The Terminal Cover omes with the models. Waterproof Paking Note: The Waterproof Paking is inluded with the Controller only for models with terminal bloks. Current Transformers (CTs) Terminal blok models E53-COV7 odel Y92S-29 Hole diameter odel 5.8 dia. E54-CT 2. dia. E54-CT3 Adapter Connetable models Terminal blok models Note: Use this Adapter when the panel has been previously prepared for the Sokets (for Plug-in odels) Type Front-onneting Soket Front-onneting Soket with Finger Protetion Bak-onneting Soket Terminal Cover for Bak-onneting soket with Finger Protetion C-Thermo Support Software odel EST2-2C-V4 odel Y92F-45 odel P2CF- P2CF--E P3GA- Y92A-48G -U (48 x 48 mm) Safety Preautions Operation -H (48 x 48 mm) 7

8 -U (48 x 48 mm) -H (48 x 48 mm) /-U Speifiations Ratings Power supply voltage Operating voltage range Power onsumption Sensor Input impedane Control method Control s Auxiliary s -U No D in model number: to 24 VAC, 5/6 Hz D in model number: 24 VAC, 5/6 Hz; 24 VDC 85% to % of rated supply voltage to 24 VAC: 7.5 VA (max.) (-R2T at VAC: 3. VA) 24 VAC/VDC: 5 VA/3 W (max.) (-R2TD at 24 VAC: 2.7 VA) to 24 VAC: 6 VA (max.) 24 VAC/VDC: 3 VA/2 W (max.) (models with urrent : 4 VA/2 W) odels with temperature s Thermoouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistane thermometer: Pt or JPt Infrared temperature sensor: to 7 C, 6 to 2 C, 5 to 65 C, or 4 to 26 C Voltage : to 5 mv odels with analog s Current : 4 to 2 ma or to 2 ma Voltage : to 5 V, to 5 V, or to V Current : 5 Ω max., Voltage : Ω min. (Use a : onnetion when onneting the ES2-HB.) / ontrol or 2-PID ontrol (with auto-tuning) -U -U ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma DT, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Output voltage: 2 VDC ±5% (PNP), max. load urrent: 2 ma, with short-iruit protetion iruit 4 to 2 ma DC/ to 2 ma DC, load: 6 Ω max., resolution: approx., Long-life relay Number of s Output speifiations Number of s 2 ST-NO, 25 VAC, 3 A (resistive load), eletrial life:,, operations, load power supply voltage: 75 to 25 VAC (DC loads annot be onneted.), minimum appliable load: 5 V, ma, leakage urrent: 5 ma max. (25 VAC, 6 Hz) or 2 max. (Depends on the model.) : ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Event External ontat Contat : : kω max., : kω min. s speifiations Non-ontat : : Residual voltage:.5 V max., : Leakage urrent:. ma max. Current flow: Approx. 7 ma per ontat External power supply for ESB 2 VDC ±%, 2 ma, short-iruit protetion iruit provided Setting method Indiation method ulti Bank swithing Other funtions Digital setting using front panel keys -segment digital display and individual indiators (7-segment display also possible) Charater height: PV: mm, SV: 6.5 mm Up to four set points ( to 3) an be saved and seleted using event s, key operations, or serial ommuniations. Not supported anual, heating/ooling ontrol, loop burnout alarm, ramp, other alarm funtions, heater burnout detetion, 4% AT, % AT, V limiter, digital filter, self-tuning, temperature shift, run/stop, protetion funtions, ontrol / ounter, extration of square root, V hange rate limit, logi operations, PV/SV status display, simple program, automati ooling oeffiient adjustment Ambient operating temperature to 55 C (with no ondensation or iing), for 3-year warranty: to 5 C Ambient operating humidity 25% to 85% Storage temperature 25 to 65 C (with no ondensation or iing) 8

9 /-U Input Ranges Thermoouple/Platinum Resistane Thermometer (Universal Inputs) Temperature range ( C) Input Type Platinum resistane thermometer odels with Analog Inputs Shaded settings are the default settings. Thermoouple Name Pt JPt K J T E L U N R S B W PL II Setting number Infrared temperature sensor to 7 C 6 to 2 C 5 to 65 C 4 to 26 C Analog to 5 mv -U (48 x 48 mm) -H (48 x 48 mm) Safety Preautions Operation Shaded settings are the default settings. The appliable standards for the types are as follows: K, J, T, E, N, R, S, B: JIS C , IEC 584- L: Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W26Re, AST E Input Type Current Voltage Input speifiation 4 to 2mA to 2 ma to 5 V to 5 V to V Setting range Usable in the following ranges by saling: 999 to 9999, 99.9 to 999.9, 9.99 to or.999 to Setting number Usable in the following ranges by saling: 999 to 9999 or 99.9 to JPt: JIS C , JIS C Pt: JIS C , IEC 75 PL II: Aording to Platinel II eletromotive fore harts from BASF (previously Engelhard) 9

10 /-U -U (48 x 48 mm) -H (48 x 48 mm) Alarm Outputs Eah alarm an be independently set to one of the following 3 alarm types. The default is 2: Upper limit. Auxiliary s are alloated for alarms. delays and delays ( to 999 s) an also be speified. Note: For models with heater burnout, SSR failure, and heater overurrent detetion, alarm will be an OR of the alarm seleted from the following alarm types and the alarms for heater burnout, SSR failure, and heater overurrent. To only a heater burnout alarm, SSR failure alarm, and heater overurrent alarm for alarm, set the alarm type to (i.e., no alarm funtion). Set value Alarm type Alarm funtion Upper- and lowerlimit 2 Upper limit 3 Lower limit Upper- and lowerlimit range Upper- and lowerlimit with standby sequene Upper-limit with standby sequene Lower-limit with standby sequene Absolute-value upper-limit Absolute-value lower-limit Absolute-value upper-limit with standby sequene Absolute-value lower-limit with standby sequene LBA (for alarm only) PV hange rate alarm Alarm operation When is positive Output L L L H H H When is negative. With set values, 4 and 5, the upper and lower limit values an be set independently for eah alarm type, and are expressed as L and H. 2. Set value:, Upper- and lower-limit alarm Case L H H <, L > H < L Case 2 L H H >, L < H > L 3. Set value: 4, Upper- and lower-limit range Case L H H <, L > H < L Case 2 L H H >, L < H > L Case 3 (Always ) 4. Set value: 5, Upper- and lower-limit with standby sequene For Upper- and Lower-Limit Alarm Desribed Above Case and 2 Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always 5. Set value: 5, Upper- and lower-limit with standby sequene Always when the upper-limit and lower-limit hysteresis overlaps. H H L H L L Case 3 (Always ) H H L H L L H <, L < H <, L > H L H >, L < H L H <, L < H <, L > H L H >, L < H L

11 /-U Charateristis Indiation auray Influene of temperature 2 Influene of voltage 2 Input sampling period Hysteresis Thermoouple: Terminal blok models (): (±.3% of indiated value or ± C, whihever is greater) ± digit max. Plug-in models (-U): (±% of indiated value or ±2 C, whihever is greater) ± digit max. Platinum resistane thermometer : Terminal blok models () and plug-in models (-U): (±.2% of indiated value or ±.8 C, whihever is greater) ± digit max. Analog : Terminal blok models () and plug-in models (-U): ±.2% FS ± digit max. CT : Terminal blok models (): ±5% FS ± digit max. Thermoouple (R, S, B, W, PL II): Terminal blok models (): (±% of PV or ± C, whihever is greater) ± digit max. Plug-in models (-U): (±2% of PV or ± C, whihever is greater) ± digit max. Other thermoouple : 3 Terminal blok models (): (±% of PV or ±4 C, whihever is greater) ± digit max. Plug-in models (-U): (±2% of PV or ±4 C, whihever is greater) ± digit max. Platinum resistane thermometer : Terminal blok models () and plug-in models (-U): (±% of PV or ±2 C, whihever is greater) ± digit max. Analog : Terminal blok models () and plug-in models (-U): (±%FS) ± digit max. 25 ms odels with thermoouple/platinum resistane thermometer (universal ):. to EU (in units of. EU) 4 odels with analog :. to 99.99% FS (in units of.% FS) Proportional band (P) odels with thermoouple/platinum resistane thermometer (universal ):. to EU (in units of. EU) 4 odels with analog :. to 999.9% FS (in units of.% FS) Integral time (I) to 3999 s (in units of s) Derivative time (D) to 3999 s (in units of s) 5 Control period.5, to 99 s (in units of s) anual reset value. to.% (in units of.%) Alarm setting range Affet of signal soure resistane Insulation resistane Dieletri strength Vibration alfuntion resistane Destrution Shok alfuntion resistane Destrution Weight Degree of protetion -U -U emory protetion Setup Tool Setup Tool port Standards EC Approved standards 7 Conformed standards 999 to 9999 (deimal point position depends on type) Thermoouple:. C/Ω max. ( Ω max.) Platinum resistane thermometer:. C/Ω max. ( Ω max.) 2 Ω min. (at 5 VDC) 2,3 VAC, 5 or 6 Hz for min (between terminals with different harge) to 55 Hz, 2 m/s 2 for min eah in, Y, and Z diretions to 55 Hz,.75-mm single amplitude for 2 hrs eah in, Y, and Z diretions m/s 2, 3 times eah in, Y, and Z diretions 3 m/s 2, 3 times eah in, Y, and Z diretions Controller: Approx. 5 g, ounting Braket: Approx. g Controller: Approx. g, ounting Braket: Approx. g Front panel: IP66, Rear ase: IP2, Terminals: IP Front panel: IP5, Rear ase: IP2, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4. or higher Provided on the bottom of the. Use this port to onnet a omputer to the when using the Setup Tool. An E58-CIFQ USB-Serial Conversion Cable is required to onnet the omputer to the. 6 UL 6-, CSA C22.2 No. - EN 6- (IEC 6-): Pollution level 2, overurrent ategory II EI: EN 6326 Radiated Interferene Eletromagneti Field Strength: EN 55 Group, lass A Noise Terminal Voltage: EN 55 Group, lass A ES: EN 6326 ESD Immunity: EN Eletromagneti Field Immunity: EN Burst Noise Immunity: EN Conduted Disturbane Immunity: EN Surge Immunity: EN Power Frequeny agneti Field Immunity: EN Voltage Dip/Interrupting Immunity: EN The indiation auray of K thermoouples in the 2 to 3 C range, T and N thermoouples at a temperature of C max., and U and L thermoouples at any temperatures is ±2 C ± digit max. The indiation auray of the B thermoouple at a temperature of 4 C max. is not speified. The indiation auray of B thermoouples in the 4 to 8 C range is ±3 C max. The indiation auray of the R and S thermoouples at a temperature of 2 C max. is ±3 C ± digit max. The indiation auray of W thermoouples is ±.3 of PV or ±3 C, whihever is greater, ± digit max. The indiation auray of PL II thermoouples is ±.3 of PV or ±2 C, whihever is greater, ± digit max. 2. Ambient temperature: C to 23 C to 55 C, Voltage range: 5% to % of rated voltage 3. K thermoouple at C max.: ± max. 4. EU stands for Engineering Unit and is used as the unit after saling. For a temperature sensor, the EU is C or F. 5. When robust tuning (RT) is, the differential time is. to (in units of. s). 6. External ommuniations (RS-485) and able ommuniations for the Setup Tool an be used at the same time. 7. The -U plug-in model is ertified for UL listing only when used together with the OR P2CF- or P2CF--E Soket. The P3GA- is not ertified for UL listing. -U (48 x 48 mm) -H (48 x 48 mm) Operation Safety Preautions

12 /-U -U (48 x 48 mm) -H (48 x 48 mm) USB-Serial Conversion Cable Appliable OS Appliable software Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher Appliable models E5AN/E5EN//-U/E5AN-H/ E5EN-H/-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature Ambient operating humidity 384 bps Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 7 ma to 55 C (with no ondensation or iing) % to 8% Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Speifiations Transmission line onnetion method Synhronization method Protool Baud rate Transmission ode Data bit length Stop bit length Error detetion Flow ontrol Interfae Retry funtion buffer response wait time 2, m max. Approx. g RS-485: ultipoint RS-485 (two-wire, half duplex) Start-stop synhronization CompoWay/F, SYSWAY, or odbus 2, 24, 48, 96, 92, 384, or 576 bps ASCII 7 or 8 bits or 2 bits Vertial parity (none, even, odd) Frame hek sequene (FCS) with SYSWAY Blok hek harater (BCC) with CompoWay/F or CRC-6 odbus None RS-485 None 27 bytes to 99 ms Default: 2 ms The baud rate, data bit length, stop bit length, and vertial parity an be individually set using the Setting Level. Current Transformer (Order Separately) Ratings Dieletri strength, VAC for min Vibration resistane 5 Hz, 98 m/s 2 Weight Aessories (E54-CT3 only) E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Armatures (2) Plugs (2) Heater Burnout Alarms, SSR Failure Alarms, and Heater Overurrent Alarms CT (for heater urrent detetion) aximum heater urrent Input urrent indiation auray Heater burnout alarm setting range SSR failure alarm setting range 2 Heater overurrent alarm setting range 3 odels with detetion for single-phase heaters: One odels with detetion for single-phase or three-phase heaters: Two s 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. For heater burnout alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is lower than the set value (i.e., heater burnout detetion urrent value). 2. For SSR failure alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., SSR failure detetion urrent value). 3. For heater overurrent alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., heater overurrent detetion urrent value). Eletrial Life Expetany Curve for Relays (Referene Values) Life ( 4 operations) VAC, 3 VDC (resistive load) osφ = Swithing urrent (A) Note: Do not onnet a DC load to a Controller with a Long-life Relay Output. 2

13 External Connetions /-U A voltage (ontrol, for driving SSR) is not eletrially insulated from the internal iruits. When using a grounding thermoouple, do not onnet any of the ontrol terminals to ground. (If the ontrol terminals are onneted to ground, errors will our in the measured temperature values as a result of leakage urrent.) Consult with your OR representative before using the external power supply for the ESB for any other purpose. Controllers -U (48 x 48 mm) Control Long-life relay 25 VAC, 3 A (resistive load) 25 VAC, 3 A (resistive load) 2 VDC, 2 ma to 2 ma DC 4 to 2 ma DC Load: 6 Ω max. Control 2 2 VDC, 2 ma Option Units E53-CNHH3N2 (RS-485) and CT2 CT2 B(+) RS A( ) 3 CT 4 5 E53-CNH3N2 (RS-485) and CT B(+) RS A( ) DO NOT 3 4 CT 5 EV EV2 CT + Control + DO NOT DO NOT A ma B V DO NOT B + + TC/Pt Analog universal E53-CNHBN2 Event s and CT E53-CN3N2 (RS-485) B(+) RS A( ) DO NOT 3 DO NOT 4 DO NOT 5 E53-CNQ3N2 (RS-485) and Control Output 2 B(+) RS A( ) DO NOT Control 2 5 E53-CNBN2 Event s 2 EV 3 EV2 DO NOT 4 DO NOT 5 Auxiliary s (relay s) 25 VAC, 3 A (resistive load) Auxiliary s (relay s) Auxiliary 2 Auxiliary Input power supply to 24 VAC 24 VAC/VDC (no polarity) E53-CNPBN2 Event Inputs and External Power Supply 2 EV 3 EV2 + External 4 2 VDC, power supply 2 ma 5 E53-CNQHN2 Control Output 2 and CT + Control 2 2 DO NOT CT E53-CNPHN2 External Power Supply and CT External + power supply DO NOT CT A heater burnout alarm, heater short alarm, heater overurrent alarm, or alarm is sent to the to whih the alarm funtion is assigned. 2 VDC, 2 ma E53-CNQHHN2 Control Output 2 and CT2 + Control 2 2 CT2 CT E53-CNP3N2 (RS-485) and External Power Supply B(+) RS A( ) DO NOT 3 + External 4 2 VDC, power supply 2 ma 5 E53-CNQBN2 Event Inputs and Control Output 2 2 EV 3 EV2 + 4 Control 2 5 -H (48 x 48 mm) -U Control Control (three terminals used) DT, 25 VAC, 3 A (resistive load) DO NOT DO NOT A ma B 2 VDC, 2 ma V DO NOT 4 to 2 ma DC B to 2 ma DC Load: 6 W max. Analog TC/Pt universal Note: For the Wiring Soket, purhase the P2CF- or PG3A- separately. Auxiliary 25 VAC, 3 A (resistive load) (s) Auxiliary Auxiliary 2 (Control (ooling side)) Input power supply to 24 VAC 24 VAC/VDC (no polarity) An error is sent to the to whih the alarm funtion is assigned. Operation Safety Preautions 3

14 /-U Nomenlature -U (48 x 48 mm) -U The front panel is the same for the and -U. Operation indiators Temperature unit No. display No. 2 display Level Key Up Key Dimensions ode Key Down Key (Unit: mm) -H (48 x 48 mm) Terminal odels -U Plug-in odels Waterproof ounting Adapter Paking (Aessory) (Aessory) Terminal Cover (E53-COV7) (Aessory) Panel Cutout ounted Separately 6 min. Note: The terminal blok annot be removed. (84.7) Panel Cutout ounted Separately Group ounted (48 number of units 2.5) +. Group mounting does not allow waterproofing Reommended panel thikness is to 5 mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof paking onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. Group ounted (48 number of units 2.5) Aessories (Order Separately) USB-Serial Conversion Cable E58-CIFQ ounting Adapter (Aessory) USB onnetor (type A plug) 6 min (2,) 25 LED indiator (SD),765 LED indiator (RD) Reommended panel thikness is to 5 mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. Serial onnetor 4

15 /-U Terminal Cover E53-COV Note: The E53-COV annot be used. Waterproof Paking Y92S-29 (for DIN 48 48) Order the Waterproof Paking separately if it beomes lost or damaged. The Waterproof Paking an be used to ahieve an IP66 degree of protetion. (Deterioration, shrinking, or hardening of the waterproof paking may our depending on the operating environment. Therefore, periodi replaement is reommended to ensure the level of waterproofing speified in IP66. The time for periodi replaement depends on the operating environment. Be sure to onfirm this point at your site. Consider one year a rough standard. OR shall not be liable for the level of water resistane if the ustomer does not perform periodi replaement.) The Waterproof Paking does not need to be attahed if a waterproof struture is not required. -U (48 x 48 mm) 9. Current Transformers E54-CT E54-CT dia..5 Two, 3.5 dia dia. 2 dia E54-CT Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 5 A (5/6 Hz) Number of windings: 4±2 Winding resistane: 8±2 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω Ω RL = Ω Distortion fator % 3% % -H (48 x 48 mm) ma, A 4 4 Thru-urrent (Io) A (r.m.s.) 5 3 Two, 3 (depth: 4) E54-CT3 Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 2 A (5/6 Hz) (aximum ontinuous heater urrent for the Temperature Controller is 5 A.) Number of windings: 4±2 Winding resistane: 8±.8 Ω Operation E54-CT3 Aessory Armature Approx. 3 dia. Plug Approx. 6 dia. (22) 8 Connetion Example Armature Plug Lead Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω 5 Ω Ω 5 Ω RL = Ω Distortion fator % 3% % ma, A Thru-urrent (Io) A (r.m.s.) Safety Preautions 5

16 /-U -U (48 x 48 mm) Adapter Y92F-45 Note: Use this Adapter when the panel has already been prepared for the E5B@ to Fixture (Aessory) ounted to Panel ( to 8 mm) -H (48 x 48 mm) (to bak of ) -U Wiring Soket Front-onneting Soket P2CF- Eleven, sems srews max. Two, 4.5-dia. holes Terminal Layout/Internal Connetions (Top View) ounting Holes Two, 4.5 dia. mounting holes 4±.2 Note: Can also be mounted to a DIN trak. 4 5 max. 3.2 max. Note: A model with finger protetion (P2CF--E) is also available. Bak-onneting Soket P3GA dia Note:. Using any other sokets will adversely affet auray. Use only the speified sokets. 2. A Protetive Cover for finger protetion (Y92A-48G) is also available Terminal Layout/Internal Connetions (Bottom View)

17 Basi-type Digital Temperature Controller E5AN/E5EN (96 x 96 mm and 48 x 96 mm) New 96 x 96-mm and 48 x 96-mm Basi Temperature Controllers with Enhaned Funtions and Performane. Improved Indiation Auray and Preventive aintenane Funtion. Indiation Auray Thermoouple : ±.3% of PV (previous models: ±.5%) Pt : ±.2% of PV (previous models: ±.5%) Analog : ±.2% FS (previous models: ±.5%) A PV/SV-status display funtion an be set to automatially alternate between displaying the status of the Temperature Controller (auto/manual, RUN/STOP, and alarms) and the PV or SV. Preventive maintenane for relays in the Temperature Controller using a Control Output / Counter. Three-level display that simultaneously displays the PV, SV, and V. One-touh operation with PF Key that an be assigned to auto/manual, RUN/ STOP, or other funtions. ain I/O Funtions Sensor Inputs Universal thermoouple/pt s (odels with temperature s) Analog urrent/voltage s (odels with analog s) Indiation Auray Thermoouple : ±.3% of PV Pt : ±.2% of PV Analog : ±.2% FS Sampling Period 25 ms Event Inputs None Two PF Key (Programmable funtion key) E5AN Control Output 2 Long-life relay (hybrid) E5EN Control Output Auxiliary Outputs Three mm E5AN mm E5EN Refer to Safety Preautions on page level Display Simultaneously displays set items, suh as the PV, SV, and V. A 2-level display when shipped from the fatory. A 3-level display is ativated if parameters are initialized. For details on the third display level, refer to the User s anual, Basi Type (Cat. No. H56). 4-digit Display Auto/manual swithing Temperature Controller status display Simple program funtion Control / ount alarm PV hange rate alarm odels also available with RS-485 or RS-232C ommuniations This data sheet is provided as a guideline for seleting produts. Be sure to refer to the following user manuals for appliation preautions and other information required for operation before attempting to use the produt. /E5AN/E5EN Digital Temperature Controllers User's anual Basi Type (Cat. No. H56) /E5AN/E5EN Digital Temperature Controllers anual Basi Type (Cat. No. H58) -U (48 x 48 mm) -H (48 x 48 mm) 7

18 E5AN/E5EN Lineup -U (48 x 48 mm) E5AN/E5EN Basi Type Terminal blok Temperature ontrol 2 ontrol s ontrol 3 auxiliary s 3 auxiliary s 3 auxiliary s Analog 2 ontrol s 3 auxiliary s -H (48 x 48 mm) Note: odels with one ontrol or two ontrol s an be used for heating/ooling ontrol. odel Number Struture odel Number Legend Controllers E5AN/E5EN-@3@@@-@-5-N Control Output R: Q: C: 2. Auxiliary Outputs 3: Three s 3. Heater Burnout/SSR Failure, Control Output 2, or External Power Supply for ESB Blank: None Q: Control 2 (voltage for driving SSR) Y: Long-life relay (hybrid) H: Heater burnout/ssr failure/heater overurrent detetion (CT) HH: Heater burnout/ssr failure/heater overurrent detetion (CT2) P: Power supply for sensor 4. Option : Option Unit an be mounted. 5. Input Type T: Universal thermoouple/platinum resistane thermometer L: Analog urrent/voltage 6. Power Supply Voltage Blank: to 24 VAC D: 24 VAC/VDC 7. Case Color Blank: Blak W: Silver 8. Terminal Cover -5: With terminal over 9. Version N: Available only to models released after January 28. Option Units E53-@. Funtion EN: RS-232C ommuniations EN3: RS-485 ommuniations AKB: Event 8

19 Ordering Information E5AN Controllers with Terminal Bloks Size /4 DIN (W H D) Case olor Blak Silver Power supply voltage to 24 VAC 24 VAC/ VDC to 24 VAC 24 VAC/ VDC Input type Thermoouple or Resistane thermometer Analog (urrent/voltage) Thermoouple or Resistane thermometer Thermoouple or Resistane thermometer Auxiliary s Control Heater burnout Funtions Power supply for Sensor Control 2 E5AN/E5EN odel E5AN-R3T-5-N E5AN-Q3T-5-N E5AN-C3T-5-N E5AN-R3HT-5-N for driving SSR) E5AN-Q3HT-5-N 2 E5AN-R3HHT-5-N for driving SSR) 2 E5AN-Q3HHT-5-N Voltage Voltage E5AN-R3QT-5-N E5AN-Q3QT-5-N Voltage E5AN-C3QT-5-N E5AN-R3YT-5-N Long-life relay E5AN-Q3YT-5-N E5AN-C3YT-5-N Sensor Power E5AN-R3PT-5-N Sensor Power E5AN-Q3PT-5-N E5AN-R3L-5-N E5AN-Q3L-5-N E5AN-C3L-5-N E5AN-R3HL-5-N E5AN-Q3HL-5-N Long-life relay E5AN-Q3YL-5-N E5AN-R3TD-5-N E5AN-Q3TD-5-N E5AN-C3TD-5-N E5AN-R3HTD-5-N E5AN-Q3HTD-5-N 2 E5AN-R3HHTD-5-N 2 E5AN-Q3HHTD-5-N E5AN-R3T-W-5-N E5AN-Q3T-W-5-N E5AN-C3T-W-5-N E5AN-R3HT-W-5-N E5AN-Q3HT-W-5-N E5AN-R3TD-W-5-N E5AN-Q3TD-W-5-N E5AN-C3TD-W-5-N -U (48 x 48 mm) -H (48 x 48 mm) 9

20 E5AN/E5EN -U (48 x 48 mm) -H (48 x 48 mm) E5EN Controllers with Terminal Bloks Size /8 DIN (W H D) Case olor Blak Silver Power supply voltage to 24 VAC 24 VAC/ VDC to 24 VAC 24 VAC/ VDC Input type Thermoouple or Resistane thermometer Analog (urrent/voltage) Thermoouple or Resistane thermometer Thrmoouple or Resistane thermometer Auxiliary s Control Heater burnout Funtions Power supply for Sensor Control 2 odel E5EN-R3T-5-N E5EN-Q3T-5-N E5EN-C3T-5-N E5EN-R3HT-5-N E5EN-Q3HT-5-N 2 E5EN-R3HHT-5-N 2 E5EN-Q3HHT-5-N Voltage Voltage Voltage Long-life relay Long-life relay E5EN-R3QT-5-N E5EN-Q3QT-5-N E5EN-C3QT-5-N E5EN-R3YT-5-N E5EN-Q3YT-5-N Long-life relay E5EN-C3YT-5-N Sensor Power E5EN-R3PT-5-N Sensor Power E5EN-Q3PT-5-N E5EN-R3L-5-N E5EN-Q3L-5-N E5EN-C3L-5-N E5EN-R3HL-5-N E5EN-Q3HL-5-N Long-life E5EN-Q3YL-5-N relay E5EN-R3TD-5-N E5EN-Q3TD-5-N E5EN-C3TD-5-N E5EN-R3HTD-5-N E5EN-Q3HTD-5-N 2 E5EN-R3HHTD-5-N 2 E5EN-Q3HHTD-5-N E5EN-R3T-W-5-N E5EN-Q3T-W-5-N E5EN-C3T-W-5-N E5EN-R3HT-W-5-N E5EN-Q3HT-W-5-N E5EN-R3TD-W-5-N E5EN-Q3TD-W-5-N E5EN-C3TD-W-5-N 2

21 E5AN/E5EN Option Units Name Funtion odel RS-232C ommuniations E53-EN Unit RS-485 ommuniations E53-EN3 Event Input Unit Event s E53-AKB Aessories (Order Separately) USB-Serial Conversion Cable Current Transformers (CTs) -U (48 x 48 mm) odel E58-CIFQ Connetable models odel E5AN E53-COV6 E5EN Terminal Cover Note: The Terminal Cover omes with the -@@@-5 models. Waterproof Paking Connetable models odel E5AN Y92S-P4 E5EN Y92S-P5 Note: The Waterproof Paking is inluded with the Controller. Hole diameter odel 5.8 dia. E54-CT 2. dia. E54-CT3 C-Thermo Support Software odel EST2-2C-V4 -H (48 x 48 mm) 2

22 E5AN/E5EN Speifiations -U (48 x 48 mm) -H (48 x 48 mm) Ratings Power supply voltage Operating voltage range Power onsumption Sensor Input impedane Control method Control Auxiliary Event No D in model number: to 24 VAC, 5/6 Hz D in model number: 24 VAC, 5/6 Hz; 24 VDC 85% to % of rated supply voltage to 24 VAC: VA 24 VAC/VDC: 5.5 VA (24 VAC)/4 W (24 VDC) odels with temperature s Thermoouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistane thermometer: Pt or JPt Infrared temperature sensor: to 7 C, 6 to 2 C, 5 to 65 C, or 4 to 26 C Voltage : to 5 mv odels with analog s Current : 4 to 2 ma or to 2 ma Voltage : to 5 V, to 5 V, or to V Current : 5 Ω max., Voltage : Ω min. (Use a : onnetion when onneting the ES2-HB.) / ontrol or 2-PID ontrol (with auto-tuning) ST-NO, 25 VAC, 5 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Output voltage: 2 VDC ±5% (PNP), max. load urrent: 4 ma, With short-iruit protetion iruit: ax. load urrent of 2 ma for ontrol 2 4 to 2 ma DC/ to 2 ma DC, load: 6 Ω max., resolution: approx., Long-life relay Number of s 3 Output speifiations Number of s 2 External ontat speifiations ST-NO, 25 VAC, 3 A (resistive load), eletrial life:,, operations, load power supply voltage: 75 to 25 VAC (DC loads annot be onneted.), minimum appliable load: 5 V, ma, leakage urrent: 5 ma max. (25 VAC, 6 Hz) : ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Contat : : kω max., : kω min. Non-ontat : : Residual voltage:.5 V max., : Leakage urrent:. ma max. Current flow: Approx. 7 ma per ontat External power supply for ESB 2 VDC ±%, 2 ma, short-iruit protetion iruit provided Setting method Digital setting using front panel keys -segment digital display and individual indiators (7-segments displays also possible) Charater height: E5AN: PV: 5.8 mm, SV: 9.5 mm, V: 6.8 mm; E5EN: PV:.8 mm, SV: 8. mm, Indiation method V: 5.8 mm Content of 3-level display: PV/SV/V, PV/SV/multi-, or soak time remain Number of digits: 4 for PV, SV, and V Up to four set points ( to 3) an be saved and seleted using event s, key operations, or serial ulti ommuniations. Bank swithing Not supported. anual, heating/ooling ontrol, loop burnout alarm, ramp, other alarm funtions, heater burnout detetion, 4% AT, % AT, V limiter, digital filter, self-tuning, temperature shift, run/stop, Other funtions protetion funtions, ontrol / ounter, extration of square root, V hange rate limit, logi operations, PV/SV status display, simple program, automati ooling oeffiient adjustment Ambient operating temperature to 55 C (with no ondensation or iing), for 3-year warranty: to 5 C Ambient operating humidity 25% to 85% Storage temperature 25 to 65 C (with no ondensation or iing) A 2-level display when shipped from the fatory. A 3-level display is ativated if parameters are initialized. For details on the third display level, refer to the User s anual, Basi Type (Cat. No. H56). 22

23 E5AN/E5EN Input Ranges Thermoouple/Platinum Resistane Thermometer (Universal s) Temperature range ( C) Input type Platinum resistane thermometer odels with Analog Inputs Shaded settings are the default settings. Thermoouple Name Pt JPt K J T E L U N R S B W PL II Setting number Infrared temperature sensor Shaded settings are the default settings. The appliable standards for the types are as follows: K, J, T, E, N, R, S, B: JIS C , IEC 584- L: Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W26Re, AST E Input type Current Voltage Input speifiation 4 to 2mA to 2 ma to 5 V to 5 V to V Setting range Usable in the following ranges by saling: 999 to 9999, 99.9 to 999.9, 9.99 to or.999 to Setting number to 7 C 6 to 2 C 5 to 65 C 4 to 26 C Analog to 5 mv Usable in the following ranges by saling: 999 to 9999 or 99.9 to JPt: JIS C , JIS C Pt: JIS C , IEC 75 PL II: Aording to Platinel II eletromotive fore harts from BASF (previously Engelhard) -U (48 x 48 mm) -H (48 x 48 mm) 23

24 E5AN/E5EN -U (48 x 48 mm) -H (48 x 48 mm) Alarm Outputs Eah alarm an be independently set to one of the following 3 alarm types. The default is 2: Upper limit. Auxiliary s are alloated for alarms. delays and delays ( to 999 s) an also be speified. Note: For models with heater burnout, SSR failure, and heater overurrent detetion, alarm will be an OR of the alarm seleted from the following alarm types and the alarms for heater burnout, SSR failure, and heater overurrent. To only a heater burnout alarm, SSR failure alarm, and heater overurrent alarm for alarm, set the alarm type to (i.e., no alarm funtion). Set value Alarm type Alarm funtion Upper- and lower-limit 2 Upper limit 3 Lower limit Upper- and lower-limit range Upper- and lower-limit with standby sequene 5 Upper-limit with standby sequene Lower-limit with standby sequene Absolute-value upper-limit Absolute-value lower-limit Absolute-value upper-limit with standby sequene Absolute-value lower-limit with standby sequene LBA (for alarm only) PV hange rate alarm Alarm operation When is positive Output L L L H H H When is negative. With set values, 4 and 5, the upper and lower limit values an be set independently for eah alarm type, and are expressed as L and H. 2. Set value:, Upper- and lower-limit alarm Case L H H <, L > H < L Case 2 L H H >, L < H > L 3. Set value: 4, Upper- and lower-limit range Case L H H <, L > H < L Case 2 L H H >, L < H > L Case 3 (Always ) 4. Set value: 5, Upper- and lower-limit with standby sequene For Upper- and Lower-Limit Alarm Desribed Above Case and 2 Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always 5. Set value: 5, Upper- and lower-limit with standby sequene Always when the upper-limit and lower-limit hysteresis overlaps. H H L H L L Case 3 (Always ) H H L H L L H <, L < H <, L > H L H >, L < H L H <, L < H <, L > H L H >, L < H L 24

25 E5AN/E5EN Charateristis Indiation auray Transfer auray Influene of temperature 2 Influene of voltage 2 Input sampling period Hysteresis Proportional band (P) Thermoouple: (±.3% of indiated value or ± C, whihever is greater) ± digit max. Platinum resistane thermometer: (±.2% of indiated value or ±.8 C, whihever is greater) ± digit max. Analog : ±.2% FS ± digit max. CT : ±5% FS ± digit max. ±.3% FS max. Thermoouple (R, S, B, W, PL II): (±% of PV or ± C, whihever is greater) ± digit max. Other thermoouple : (±% of PV or ±4 C, whihever is greater) ± digit max. 3 Platinum resistane thermometer: (±% of PV or ±2 C, whihever is greater) ± digit max. Analog : (±%FS) ± digit max. 25 ms odels with thermoouple/platinum resistane thermometer (universal ):. to EU (in units of. EU) 4 odels with analog :. to 99.99% FS (in units of.% FS) odels with thermoouple/platinum resistane thermometer (universal ):. to EU (in units of. EU) 4 odels with analog :. to 999.9% FS (in units of.% FS) Integral time (I) to 3999 s (in units of s) Derivative time (D) to 3999 s (in units of s) 5 Control period.5, to 99 s (in units of s) anual reset value. to.% (in units of.%) Alarm setting range 999 to 9999 (deimal point position depends on type) Affet of signal soure resistane Insulation resistane Dieletri strength Vibration resistane Shok resistane alfuntion Destrution alfuntion Destrution E5AN Weight E5EN Degree of protetion emory protetion Setup Tool Setup Tool port Standards EC Approved standards Conformed standards Thermoouple:. C/Ω max. ( Ω max.) Platinum resistane thermometer:. C/Ω max. ( Ω max.) 2 Ω min. (at 5 VDC) 2,3 VAC, 5 or 6 Hz for min (between terminals with different harge) to 55 Hz, 2 m/s 2 for min eah in, Y, and Z diretions to 55 Hz,.75-mm single amplitude for 2 hrs eah in, Y, and Z diretions m/s 2, 3 times eah in, Y, and Z diretions 3 m/s 2, 3 times eah in, Y, and Z diretions Controller: Approx. 3 g, ounting Braket: Approx. g Controller: Approx. 26 g, ounting Braket: Approx. g Front panel: IP66, Rear ase: IP2, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4. or higher Provided on the bottom of the E5AN and E5EN. An E58-CIFQ USB-Serial Conversion Cable is required to onnet the omputer to the E5AN and E5EN 6 UL 6-, CSA C22.2 No. - EN 6- (IEC 6-): Pollution level 2, overurrent ategory II EI: EN 6326 Radiated Interferene Eletromagneti Field Strength: EN 55 Group, lass A Noise Terminal Voltage: EN 55 Group, lass A ES: EN 6326 ESD Immunity: EN Eletromagneti Field Immunity: EN Burst Noise Immunity: EN Conduted Disturbane Immunity: EN Surge Immunity: EN Power Frequeny agneti Field Immunity: EN Voltage Dip/Interrupting Immunity: EN The indiation auray of K thermoouples in the 2 to 3 C range, T and N thermoouples at a temperature of C max., and U and L thermoouples at any temperatures is ±2 C ± digit max. The indiation auray of the B thermoouple at a temperature of 4 C max. is not speified. The indiation auray of B thermoouples in the 4 to 8 C range is ±3 C max. The indiation auray of the R and S thermoouples at a temperature of 2 C max. is ±3 C ± digit max. The indiation auray of W thermoouples is ±.3 of PV or ±3 C, whihever is greater, ± digit max. The indiation auray of PL II thermoouples is ±.3 of PV or ±2 C, whihever is greater, ± digit max. 2. Ambient temperature: C to 23 C to 55, Voltage range: 5% to % of rated voltage 3. K thermoouple at C max.: ± C max. 4. EU stands for Engineering Unit and is used as the unit after saling. For a temperature sensor, the EU is C or F. 5. When robust tuning (RT) is, the differential time is. to (in units of. s). 6. External ommuniations (RS-232C or RS-485) and able ommuniations for the Setup Tool an be used at the same time. -U (48 x 48 mm) -H (48 x 48 mm) 25

26 E5AN/E5EN -U (48 x 48 mm) -H (48 x 48 mm) USB-Serial Conversion Cable Appliable OS Appliable software Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher Appliable models E5AN/E5EN//-U/E5AN- H/E5EN-H/-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 7 ma Ambient operating humidity % to 8% to 55 C (with no ondensation or iing) Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight 2, m max. Approx. g Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Speifiations Transmission line onnetion method RS-485: ultipoint RS-232C: Point-to-point RS-485 (two-wire, half duplex) or RS- 232C Synhronization method Start-stop synhronization Protool Baud rate Transmission ode Data bit length Stop bit length Error detetion Flow ontrol Interfae Retry funtion buffer response wait time CompoWay/F, SYSWAY, or odbus 2, 24, 48, 96, 92, 384, or 576 bps ASCII 7 or 8 bits or 2 bits Vertial parity (none, even, odd) Frame hek sequene (FCS) with SYSWAY Blok hek harater (BCC) with CompoWay/F or CRC-6 odbus None RS-485, RS-232C None 27 bytes to 99 ms Default: 2 ms The baud rate, data bit length, stop bit length, and vertial parity an be individually set using the Setting Level. Current Transformer (Order Separately) Ratings Dieletri strength, VAC for min Vibration resistane 5 Hz, 98 m/s 2 Weight Aessories (E54-CT3 only) E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Armatures (2) Plugs (2) Heater Burnout Alarms, SSR Failure Alarms, and Heater Overurrent Alarms CT (for heater urrent detetion) aximum heater urrent Input urrent indiation auray Heater burnout alarm setting range SSR failure alarm setting range 2 Heater overurrent alarm setting range 3 odels with detetion for singlephase heaters: One odels with detetion for singlephase or three-phase heaters: Two s 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. For heater burnout alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is lower than the set value (i.e., heater burnout detetion urrent value). 2. For SSR failure alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., SSR failure detetion urrent value). 3. For heater overurrent alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., heater overurrent detetion urrent value). Eletrial Life Expetany Curve for Relays (Referene Values) Life ( 4 operations) E5AN/E5EN 25 VAC, 3 VDC (resistive load) osφ = Swithing urrent (A) Note: Do not onnet a DC load to a Controller with a Long-life Relay Output. 26

27 External Connetions E5AN/E5EN A voltage (ontrol, for driving SSR) is not eletrially insulated from the internal iruits. When using a grounding thermoouple, do not onnet any of the ontrol terminals to ground. If the ontrol terminals are onneted to ground, errors will our in the measured temperature values as a result of leakage urrent. The voltage (ontrol 2, for driving SSR) has basi insulation provided for the internal iruit. Consult with your OR representative before using the external power supply for the ESB for any other purpose. Controllers Option Units -U (48 x 48 mm) to 24 VAC 24 VAC/VDC (no polarity) Control 25 VAC, 5A (resistive load) 2 VDC, 4 ma to 2 ma DC 4 to 2 ma DC Load: 6 Ω max. Control 2 2 VDC, 2 ma Long-life relay 25 VAC, 3 A (resistive load) Auxiliary, 2, 3 s 25 VAC, 3 A (resistive load) Input power supply Control Auxiliary 3 Auxiliary 2 Auxiliary Event Inputs EV2 CT CT2 EV CT/CT2 Control Output 2 DO NOT DO NOT + B TC/Pt multi- - Control 2 DO NOT A B DO NOT ma V DO NOT Analog External Power Supply + External power supply 2 VDC, 2 ma - DO NOT E53-EN RS-232C SD 2 RD 3 SG E53-EN3 RS-485 B (+) 2 A ( ) 3 DO NOT E53-AKB Event s A heater burnout alarm, heater short alarm, heater overurrent alarm, or alarm is sent to the to whih the alarm funtion is assigned. 2 3 EV2 EV CT/CT2 -H (48 x 48 mm) 27

28 E5AN/E5EN Nomenlature -U (48 x 48 mm) E5AN Operation indiators Temperature unit SUB SUB2 SUB3 HA PV No. display E5EN Operation indiators Temperature unit SUB SUB2 HA SUB3 PV No. display SV No. 2 display SV No.2 display Programmable Funtion Key/ Auto/anual Key E5AN PF A/ OUT OUT2 STOP CW ANU V No. 3 display Up Key Down Key Operation indiators ode Key Level Key OUT STOP OUT2 CW ANU E5EN PF A/ V No.3 display Up Key Programmable Funtion Key/ Auto/anual Key Level Key ode Key Down Key -H (48 x 48 mm) A 2-level display when shipped from the fatory. A 3-level display is ativated if parameters are initialized. For details on the third display level, refer to the User s anual, Basi Type (Cat. No. H56). Dimensions E5AN (Unit: mm) ounted Separately Group ounted (96 number of units 3.5) min. Group mounting does not allow waterproofing. Waterproof Paking (Aessory) ounting Braket (Aessory) Terminal Cover (E53-COV6) (Aessory) Crimp terminal size: Reommended panel thikness is to 8mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof paking onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. 28

29 E5AN/E5EN E5EN ounted Separately Group ounted (48 number of units 2.5) U (48 x 48 mm) min. Group mounting does not allow waterproofing. Waterproof Paking (Aessory) Aessories (Order Separately) USB-Serial Conversion Cable E58-CIFQ Terminal Covers E53-COV6 (Six Covers provided.) ounting Braket (Aessory) USB onnetor (type A plug) 44.8 Terminal Cover (E53-COV6) (Aessory) Crimp terminal size: Reommended panel thikness is to 8 mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof paking onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. (2,) 25 LED (SD), LED (RD) Serial onnetor -H (48 x 48 mm) 29

30 E5AN/E5EN -U (48 x 48 mm) Waterproof Paking Y92S-P4 (for DIN 96 96) Current Transformers Y92S-P5 (for DIN 48 96) Order the Waterproof Paking separately if it beomes lost or damaged. The Waterproof Paking an be used to ahieve an IP66 degree of protetion. (Deterioration, shrinking, or hardening of the waterproof paking may our depending on the operating environment. Therefore, periodi replaement is reommended to ensure the level of waterproofing speified in IP66. The time for periodi replaement depends on the operating environment. Be sure to onfirm this point at your site. Consider one year a rough standard. OR shall not be liable for the level of water resistane if the ustomer does not perform periodi replaement.) The Waterproof Paking does not need to be attahed if a waterproof struture is not required. -H (48 x 48 mm) E54-CT E54-CT dia..5 Two, 3.5 dia dia. 2 dia. Two, 3 (depth: 4) E54-CT Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 5 A (5/6 Hz) Number of windings: 4±2 Winding resistane: 8±2 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω Ω RL = Ω Distortion fator % 3% % ma, A Thru-urrent (Io) A (r.m.s.) E54-CT3 Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) E54-CT3 Aessory Armature Approx. 3 dia. Plug Approx. 6 dia. (22) Connetion Example Armature Plug Lead aximum ontinuous heater urrent: 2 A (5/6 Hz) (aximum ontinuous heater urrent for an OR Temperature Controller is 5 A.) Number of windings: 4±2 Winding resistane: 8±.8 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω 5 Ω Ω 5 Ω RL = Ω Distortion fator % 3% % ma, A Thru-urrent (Io) A (r.m.s.) 3

31 Advaned Digital Temperature Controller -H (48 x 48 mm) A New High-performane Controller: High Resolution, High Speed, and High Input Auray. Logi Operations and Preventive aintenane Funtion. High-resolution display with 5 digits/. C display in a ompat Controller (48 x 48 mm). High-speed sampling yle of 6 ms. High Auray Thermoouple/Pt : ±.% of PV Analog : ±.% FS Universal s on all models (thermoouple, PT, or analog ) to handle various sensors with one Controller. A PV/SV-status display funtion an be set to automatially alternate between displaying the status of the Temperature Controller (auto/ manual, RUN/STOP, and alarms) and the PV or SV. Flexible ontat s with logi operations (AND, OR, and delays) set from the Support Software (C-Thermo Ver. 4.) Preventive maintenane for relays in the Temperature Controller using a Control Output / Counter. ain I/O Funtions Universal Sensor Inputs Universal thermoouple/pt/analog (urrent/voltage) s. Indiation Auray Thermoouple/Pt : ±.% of PV Analog : ±.% FS Sampling Period 6 ms Event Inputs None Two -H Control Output 2 None 2-level Display: PV and SV Auxiliary Outputs Two Control Output Linear voltage mm -H Refer to Safety Preautions on page digit Display with high resolution of. C Auto/manual swithing Temperature Controller status display Simple program funtion Logi operations Control / ount alarm PV hange rate alarm odels also available with RS-485 or RS-232C ommuniations This data sheet is provided as a guideline for seleting produts. Be sure to refer to the following user manuals for appliation preautions and other information required for operation before attempting to use the produt. -H/E5AN-H/E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H57) -H/E5AN-H/E5EN-H Digital Controllers anual Advaned Type (Cat. No. H59) -U (48 x 48 mm) -H (48 x 48 mm) 3

32 -H Lineup -U (48 x 48 mm) -H Advaned Type Terminal blok Note: odels with one ontrol and models with two ontrol s an be used for heating/ooling ontrol. odel Number Struture Fully universal ontrol 2 auxiliary s 2 ontrol s 2 auxiliary s -H (48 x 48 mm) odel Number Legend Controllers -@@@@-@ Type H: Advaned 2. Control Output R: Q: C: V: Linear voltage 3. Auxiliary Outputs 2: Two s 4. Option : Option Unit an be mounted. 5. Power Supply Voltage Blank: to 24 VAC D: 24 VAC/VDC 6. Case Color Blank: Blak W: Silver 7. Terminal Cover -5: With terminal over Option Units E53-@@@@ Appliable Controller CN: -H or 2. Funtion Blank: None Q: Control 2 (voltage for driving SSR) P: Power supply for sensor C: 3. Funtion 2 Blank: None H: Heater burnout/ssr failure/heater overurrent detetion (CT) HH: Heater burnout/ssr failure/heater overurrent detetion (CT2) B: Two event s 3: RS-485 ommuniations H3: Heater burnout/ssr failure/heater overurrent detetion (CT) + RS-485 ommuniations HB: Heater burnout/ssr failure/heater overurrent detetion (CT) + Two event s HH3: Heater burnout/ssr failure/heater overurrent detetion (CT2) + RS-485 ommuniations H: Heater burnout/ssr failure/heater overurrent detetion (CT)/RS-232C ommuniations F: Transfer BF: Two event s/transfer 4. Version N2: Available only to models released after January 28 Note: Not all ombinations of funtion and funtion 2 speifiations are possible for Option Units (E53-@@@@). 32

33 Ordering Information Controllers /6 DIN (W H D) Size Case Color Power supply voltage Auxiliary Control odel Option Units One of the following Option Units an be mounted to provide the with additional funtions. RS-485 RS-485 RS-485 RS-485 Note: These Option Units are appliable only to models released after January 28. Aessories (Order Separately) USB-Serial Conversion Cable Terminal Cover Blak Silver RS-232C RS-232C RS-232C to 24 VAC 2 24 VAC/VDC 2 to 24 VAC 2 24 VAC/VDC 2 Note:. The Terminal Cover omes with the -@@@-5 models. 2. The E53-COV annot be used. Waterproof Paking Funtions 3-phase heater burnout/ssr failure/ Heater overurrent detetion Heater burnout/ssr failure/ Heater overurrent detetion Heater burnout/ssr failure/ Heater overurrent detetion Note: Waterproof Paking is inluded with the ontroller only for models with terminal bloks. Current Transformers (CTs) Event s Event s Heater burnout/ssr failure/ Heater overurrent detetion 3-phase heater burnout/ssr failure/ Heater overurrent detetion Event s Heater burnout/ssr failure/ Heater overurrent detetion odel E58-CIFQ odel E53-COV7 odel Y92S-29 Hole diameter odel 5.8 dia. E54-CT 2. dia. E54-CT3 Adapter Linear voltage Linear voltage Control 2 (Voltage for driving SSR) Control 2 (Voltage for driving SSR) Control 2 (Voltage for driving SSR) Control 2 (Voltage for driving SSR) Control 2 (Voltage for driving SSR) Transfer Output -H -HR2-5 -HQ2-5 -HC2-5 -HV2-5 -HR2D-5 -HQ2D-5 -HC2D-5 -HV2D-5 -HR2-W-5 -HQ2-W-5 -HC2-W-5 -HR2D-W-5 -HQ2D-W-5 -HC2D-W-5 odel E53-CNHH3N2 E53-CNHBN2 E53-CNQ3N2 E53-CNH3N2 E53-CN3N2 E53-CNBN2 E53-CNQHN2 E53-CNQHHN2 E53-CNQBN2 E53-CNQFN2 Event s Transfer Output E53-CNBFN2 Control 2 (Voltage for driving SSR) Connetable models Terminal type E53-CNQN2 E53-CNN2 E53-CNHN2 Note: Use this Adapter when the panel has been previously prepared for the E5B@. C-Thermo Support Software odel EST2-2C-V4 odel Y92F-45 -U (48 x 48 mm) -H (48 x 48 mm) 33

34 -U (48 x 48 mm) -H (48 x 48 mm) -H Speifiations Ratings Power supply voltage Operating voltage range Power onsumption Sensor Input impedane Control method Control Linear voltage Number of s Auxiliary Event Logi operations Transfer s R Output speifiations Number of s 2 External ontat speifiations Number of operations Operations Outputs Setting method Work bit assignments Number of s Output speifiations Indiation method Bank swithing Other funtions Ambient operating temperature No D in model number: to 24 VAC, 5/6 Hz D in model number: 24 VAC, 5/6 Hz; 24 VDC 85% to % of rated supply voltage to 24 VAC: 8.5 VA (max.) (-HR2 at VAC: 3. VA) 24 VAC/VDC: 5.5 VA (24 VAC)/3.5 W (24 VDC) (max.) (-HR2D at 24 VAC: 2.7 VA) Any of the following an be seleted (i.e., fully universal ). Thermoouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistane thermometer: Pt or JPt Current : 4 to 2 ma or to 2 ma Voltage : to 5 V, to 5 V, or to V Current : 5 Ω max., Voltage : Ω min. (Use a : onnetion when onneting the ES2-HB.) / ontrol or 2-PID ontrol (with auto-tuning) ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Output voltage: 2 VDC ±5% (PNP), max. load urrent: 2 ma, with short-iruit protetion iruit 4 to 2 ma DC/ to 2 ma DC, load: 6 Ω max., resolution: approx., to VDC (load: kω min.), Resolution: Approx., 2 max. : ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma Contat : : kω max., : kω min. Non-ontat : : Residual voltage:.5 V max., : Leakage urrent:. ma max. Current flow: Approx. 7 ma per ontat 8 max. (Combinations an be made using work bits.) Logi operation: Any of the following four patterns an be seleted. The status may be inverted. (A and B) or (C and D), (A or C) and (B or D), A or B or C or D, A and B and C and D (A, B, C, and D are four s.) Delay: delay or delay for the results of the logi operation given above. Setting time: to 9999 s or to 9999 min Output inversion: Possible One work bit per operation Any of the following an be assigned to up to eight work bits (logi operation results): Event operations, auxiliary s, or ontrol s. max. : 4 to 2 ma DC, Load: 6 Ω max., Resolution at 4 to 2 ma: Approx., Not supported Ambient operating humidity 25% to 85% Storage temperature Digital setting using front panel keys -segment digital display and individual indiators (7-segments displays also possible) Charater height: PV: mm, SV: 6.5 mm Supported (number of banks: 8) Loal, alarm settings, PID sets (PID onstants, V upper limit, V lower limit, et.) anual, heating/ooling ontrol, loop burnout alarm, ramp, other alarm funtions, heater burnout detetion, 4% AT, % AT, V limiter, digital filter, self-tuning, temperature shift, run/stop, protetion funtions, ontrol / ounter, extration of square root, V hange rate limit, PV/SV status display, logi operations, automati ooling oeffiient adjustment to 55 C (with no ondensation or iing), for 3-year warranty: to 5 C 25 to 65 C (with no ondensation or iing) For models with urrent s, ontrol an be used as a transfer. 34

35 -H Input Ranges Thermoouple/Platinum Resistane Thermometer/Analog Input (Fully Universal Inputs) Temperature range ( C) Input type Platinum resistane thermometer Thermoouple Name Pt JPt K J T E L U N R S B W PL II Setting number Analog 4 to to 2 ma 2 ma 5V Usable in the following ranges by saling: to 324, to 324., to 324., or to Shaded settings are the default settings. The appliable standards for the types are as follows: K, J, T, E, N, R, S, B: JIS C , IEC 584- L: Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W26Re, AST E JPt: JIS C , JIS C Pt: JIS C , IEC 75 PL II: Aording to Platinel II eletromotive fore harts from BASF (previously Engelhard) to 5V to V -U (48 x 48 mm) -H (48 x 48 mm) 35

36 -H -U (48 x 48 mm) -H (48 x 48 mm) Alarm Outputs Eah alarm an be independently set to one of the following 3 alarm types. The default is 2: Upper limit. Auxiliary s are alloated for alarms. delays and delays ( to 999 s) an also be speified. Note: For models with heater burnout, SSR failure, and heater overurrent detetion, alarm will be an OR of the alarm seleted from the following alarm types and the alarms for heater burnout, SSR failure, and heater overurrent. To only a heater burnout alarm, SSR failure alarm, and heater overurrent alarm for alarm, set the alarm type to (i.e., no alarm funtion). Set value Alarm type Alarm funtion Upper- and lowerlimit 2 Upper limit 3 Lower limit Upper- and lowerlimit range Upper- and lowerlimit with standby sequene Upper-limit with standby sequene Lower-limit with standby sequene Absolute-value upper-limit Absolute-value lower-limit Absolute-value upper-limit with standby sequene Absolute-value lower-limit with standby sequene LBA (for alarm only) PV hange rate alarm Alarm operation When is positive Output L L L H H H When is negative. With set values, 4 and 5, the upper and lower limit values an be set independently for eah alarm type, and are expressed as L and H. 2. Set value:, Upper- and lower-limit alarm Case L H H <, L > H < L Case 2 L H H >, L < H > L 3. Set value: 4, Upper- and lower-limit range Case L H H <, L > H < L Case 2 L H H >, L < H > L Case 3 (Always ) 4. Set value: 5, Upper- and lower-limit with standby sequene For Upper- and Lower-Limit Alarm Desribed Above Case and 2 Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always 5. Set value: 5, Upper- and lower-limit with standby sequene Always when the upper-limit and lower-limit hysteresis overlaps. H H L H L L Case 3 (Always ) H H L H L L H <, L < H <, L > H L H >, L < H L H <, L < H <, L > H L H >, L < H L 36

37 -H Charateristis Indiation auray Transfer auray Influene of temperature 2 Influene of voltage 2 Input sampling period Hysteresis Thermoouple: (±.% of indiated value or ± C, whihever is greater) ± digit max. Platinum resistane thermometer: (±.% of indiated value or ±.5 C, whihever is greater) ± digit max. Analog : ±.% FS ± digit max. CT : ±5% FS ± digit max. ±.3% FS max. Thermoouple (R, S, B, W, PLII): (±% of PV or ± C, whihever is greater) ± digit max. Other thermoouple : (±% of PV or ±4 C, whihever is greater) ± digit max. 3 Platinum resistane thermometer: (±% of PV or ±2 C, whihever is greater) ± digit max. Analog : (±%FS) ± digit max. 6 ms Temperature :. to 324. C or F (in units of. C or F) Analog :.% to 99.99% FS (in units of.% FS) Proportional band (P) Temperature :. to 324. C or F (in units of. C or F) Analog :.% to 999.9% FS (in units of.% FS) Integral time (I). to 324. s (in units of. s) Derivative time (D). to 324. s (in units of. s) Control period.5, to 99 s (in units of s) anual reset value. to.% (in units of.%) Alarm setting range Affet of signal soure resistane Insulation resistane Dieletri strength Vibration alfuntion resistane Destrution Shok alfuntion resistane Destrution Weight Degree of protetion emory protetion Setup Tool Setup Tool port Standards EC Approved standards Conformed standards 9999 to 324 (deimal point position depends on type) Thermoouple:. C/Ω max. ( Ω max.) Platinum resistane thermometer:. C/Ω max. ( Ω max.) 2 Ω min. (at 5 VDC) 2,3 VAC, 5 or 6 Hz for min (between terminals with different harge) to 55 Hz, 2 m/s 2 for min eah in, Y, and Z diretions to 55 Hz,.75-mm single amplitude for 2 hrs eah in, Y, and Z diretions m/s 2, 3 times eah in, Y, and Z diretions 3 m/s 2, 3 times eah in, Y, and Z diretions Controller: Approx. 5 g, ounting Braket: Approx. g Front panel: IP66, Rear ase: IP2, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4. or higher Provided on the bottom of the -H. Use this port to onnet a omputer to the -H. An E58-CIFQ USB-Serial Conversion Cable is required to onnet the omputer to the -H. 4 UL 6-, CSA C22.2 No. - EN 6- (IEC 6-): Pollution level 2, overurrent ategory II EI: EN 6326 Radiated Interferene Eletromagneti Field Strength: EN 55 Group, lass A Noise Terminal Voltage: EN 55 Group, lass A ES: EN 6326 ESD Immunity: EN Eletromagneti Field Immunity: EN Burst Noise Immunity: EN Conduted Disturbane Immunity: EN Surge Immunity: EN Power Frequeny agneti Field Immunity: EN Voltage Dip/Interrupting Immunity: EN The indiation auray of K thermoouples in the 2 to 3 C range, T and N thermoouples at a temperature of C max., and U and L thermoouples at any temperatures is ±2 C ± digit max. The indiation auray of the B thermoouple at a temperature of 4 C max. is not speified. The indiation auray of B thermoouples in the 4 to 8 C range is ±3 C max. The indiation auray of the R and S thermoouples at a temperature of 2 C max. is ±3 C ± digit max. The indiation auray of W thermoouples is ±.3 of PV or ±3 C, whihever is greater, ± digit max. The indiation auray of PL II thermoouples is ±.3 of PV or ±2 C, whihever is greater, ± digit max. 2. Ambient temperature: C to 23 C to 55 C, Voltage range: 5% to % of rated voltage 3. K thermoouple at C max.: ± C max. 4. External ommuniations (RS-232C or RS-485) and able ommuniations for the Setup Tool an be used at the same time. -U (48 x 48 mm) -H (48 x 48 mm) 37

38 -H -U (48 x 48 mm) -H (48 x 48 mm) USB-Serial Conversion Cable Appliable OS Appliable software Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher Appliable models E5AN/E5EN//-U/ E5AN-H/E5EN-H/-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 7 ma Ambient operating humidity % to 8% to 55 C (with no ondensation or iing) Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight 2, m max. Approx. g Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Speifiations Transmission line onnetion method Synhronization method Protool Baud rate Transmission ode Data bit length Stop bit length Error detetion Flow ontrol Interfae Retry funtion buffer response wait time RS-485: ultipoint RS-232C: Point-to-point RS-485 (two-wire, half duplex)/rs-232c Start-stop synhronization CompoWay/F, SYSWAY, or odbus 2, 24, 48, 96, 92, 384, or 576 bps ASCII (CompoWay/F, SYSWAY) RTU (odbus) 7 or 8 bits or 2 bits Vertial parity (none, even, odd) Frame hek sequene (FCS) with SYSWAY Blok hek harater (BCC) with CompoWay/F or CRC-6 odbus None RS-485, RS-232C None 27 bytes to 99 ms Default: 2 ms The baud rate, data bit length, stop bit length, and vertial parity an be individually set using the Setting Level. Current Transformer (Order Separately) Ratings Dieletri strength, VAC for min Vibration resistane 5 Hz, 98 m/s 2 Weight Aessories (E54-CT3 only) E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Armatures (2) Plugs (2) Heater Burnout Alarms, SSR Failure Alarms, and Heater Overurrent Alarms CT (for heater urrent detetion) aximum heater urrent Input urrent indiation auray Heater burnout alarm setting range SSR failure alarm setting range 2 Heater overurrent alarm setting range 3 odels with detetion for singlephase heaters: One odels with detetion for singlephase or three-phase heaters: Two s 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. For heater burnout alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is lower than the set value (i.e., heater burnout detetion urrent value). 2. For SSR failure alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., SSR failure detetion urrent value). 3. For heater overurrent alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., heater overurrent detetion urrent value). Eletrial Life Expetany Curve for Relays (Referene Values) Life ( 4 operations) H 25 VAC, 3 VDC (resistive load) osφ = Swithing urrent (A) 38

39 External Connetions -H A voltage (ontrol, for driving SSR) is not eletrially insulated from the internal iruits. When using a grounding thermoouple, do not onnet any of the ontrol terminals to ground. If the ontrol terminals are onneted to ground, errors will our in the measured temperature values as a result of leakage urrent. Controllers Control 25 VAC, 3 A (resistive load) 2 VDC, 2 ma Linear voltage to VAC Load kω max. to 2 ma DC 4 to 2 ma DC Load 6 Ω max. Option Units CT2 EV EV2 DO NOT DO NOT E53-CNBN2 Event Inputs E53-CNQHHN2 Control Output 2 and CT2 Control 2 2 VDC 2 ma CT ma V DO NOT DO NOT Control DO NOT A B B Auxiliary s (relay s) Auxiliary 2 Auxiliary Note: Wire all voltage terminals orretly. The Controller may fail if voltage terminals are wired inorretly CT ? Input power supply E53-CNQBN2 E53-CNHBN2 E53-CNBFN2 Auxiliary s (relay s) 25 VAC, 3 A (resistive load) A heater burnout alarm, SSR failure, heater overurrent alarm, or alarm is sent to the to whih the alarm funtion is assigned. to 24 VAC 24 VAC/VDC (no polarity) E53-CNQFN2 E53-CNN2 E53-CNHN2 E53-CNQN2 Control Output 2 and (RS-232) Transfer Output (RS-232) (RS-232) and CT and Control Output 2 RS-232C RS-232C RS-232C SD SD SD Control 2 2 VDC 2 ma 2 RD 2 RD 2 RD 2 DO NOT SG SG SG DO NOT to 2 ma DC Control 2 Transfer DO NOT CT (Load 6 Ω 2 VDC 2 ma max.) E53-CN3N2 E53-CNQ3N2 E53-CNH3N2 E53-CNHH3N2 (RS-485) B (+) RS A ( ) DO NOT 3 DO NOT 4 DO NOT 5 EV2 Event Inputs and Control Output 2 EV Control 2 2 VDC 2 ma (RS-485) and Control Output 2 B (+) RS A ( ) DO NOT 3 4 Control 2 2 VDC 2 ma 5 EV2 Event Inputs and CT EV (RS-485) and CT B (+) RS A ( ) DO NOT 3 4 CT 5 B (+) RS A ( ) 3 CT2 Event Inputs and Transfer Output (RS-485) and CT2 CT 2 EV 3 EV2 4 Transfer to 2 ma DC (Load 6 Ω max.) Control 2 2 VDC 2 ma E53-CNQHN2 Control Output 2 and CT DO NOT CT U (48 x 48 mm) -H (48 x 48 mm) 39

40 -H Nomenlature -U (48 x 48 mm) -H Operation indiators SUB SUB2 SUB3 HA Temperature unit OUT STOP OUT2 CW ANU No. display No. 2 display Level Key Up Key Dimensions ode Key -H Down Key (Unit: mm) -H (48 x 48 mm) -H Aessories (Order Separately) USB-Serial Conversion Cable E58-CIFQ Waterproof Paking (Aessory) ounting Adapter (Aessory) Terminal Cover (E53-COV7) (Aessory) Panel Cutout ounted Separately Group ounted (48 number of units 2.5) +. 6 min Note: The terminal blok annot be removed Group mounting does not allow waterproofing Reommended panel thikness is to 5mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof paking onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. (2,) 25 LED indiator,765 (SD) USB onnetor (type A plug) LED indiator (RD) Serial onnetor 4

41 -H Terminal Cover E53-COV Current Transformers E54-CT E54-CT3 E54-CT3 Aessory Armature Approx. 3 dia. Plug Approx. 6 dia. (22) Note: The E53-COV an not be used Plug Waterproof Paking Y92S-29 (for DIN 48 48) 5.8 dia..5 Two, 3.5 dia. 2 dia. Two, 3 (depth: 4) Connetion Example dia. Armature Lead Order the Waterproof Paking separately if it beomes lost or damaged. The Waterproof Paking an be used to ahieve an IP66 degree of protetion. (Deterioration, shrinking, or hardening of the waterproof paking may our depending on the operating environment. Therefore, periodi replaement is reommended to ensure the level of waterproofing speified in IP66. The time for periodi replaement depends on the operating environment. Be sure to onfirm this point at your site. Consider one year a rough standard. OR shall not be liable for the level of water resistane if the ustomer does not perform periodi replaement.) The Waterproof Paking does not need to be attahed if a waterproof struture is not required. E54-CT Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 5 A (5/6 Hz) Number of windings: 4±2 Winding resistane: 8±2 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω Ω RL = Ω Distortion fator % 3% % ma, A Thru-urrent (Io) A (r.m.s.) E54-CT3 Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 2 A (5/6 Hz) (aximum ontinuous heater urrent for an OR Temperature Controller is 5 A.) Number of windings: 4±2 Winding resistane: 8±.8 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω 5 Ω Ω 5 Ω RL = Ω Distortion fator % 3% % ma, A Thru-urrent (Io) A (r.m.s.) -U (48 x 48 mm) -H (48 x 48 mm) 4

42 -H -U (48 x 48 mm) Adapter Y92F-45 Note: Use this Adapter when the panel has already been prepared for the E5B@ to Fixture (Aessory) ounted to -H Panel ( to 8 mm) -H (48 x 48 mm) (to bak of -H) 42

43 Advaned Digital Temperature Controller E5AN-H/E5EN-H(96 x 96 mm and 48 x 96 mm) A New High-performane Controller: High Resolution, High Speed, and High Input Auray. Logi Operations and Preventive aintenane Funtion. Plus Infrared Port on Front Panel. High-resolution display with 5 digits/. C display. High-speed sampling yle of 6 ms. High Auray Thermoouple/Pt : ±.% of PV Analog : ±.% FS Universal s on all models (thermoouple, PT, or analog ) to handle various sensors with one Controller. odels also available with Remote. A PV/SV-status display funtion an be set to automatially alternate between displaying the status of the Temperature Controller (auto/manual, RUN/STOP, and alarms) and the PV or SV. Flexible ontat s with logi operations (AND, OR, and delays) set from the Support Software (C-Thermo Ver. 4.) Preventive maintenane for relays in the Temperature Controller using a Control Output / Counter. odel available with position-proportional ontrol ain I/O Funtions Event Inputs None Two Four Universal Sensor Inputs Universal thermoouple/ Pt/analog (urrent/voltage) s. Indiation Auray Thermoouple/Pt : ±.% of PV Analog : ±.% FS Sampling Period 6 ms Remote Input One PF Key (Programmable key funtion) E5AN-H Infrared port USB Control Output 2 (built-in) SSR s Control Output (built-in) SSR s E5EN-H mm E5AN-H Auxiliary Outputs Two Three mm E5EN-H Refer to Safety Preautions on page level Display Simultaneously displays set items, suh as the PV, SV, and V. 5-digit Display with high resolution of. C Computer Support Software C-Thermo Output Unit Linear voltage Output Unit Linear voltage Auto/manual swithing Temperature Controller status display Simple program funtion Logi operations Control / ount alarm PV hange rate alarm odels available with RS-485, RS-422, or RS-232C ommuniations -U (48 x 48 mm) -H (48 x 48 mm) 43

44 E5AN-H/E5EN-H Lineup -U (48 x 48 mm) E5AN-H/E5EN-H Advaned Type Terminal blok Note: The Controller an be used for heating/ooling ontrol even if only ontrol is used. odel Number Struture Fully universal ontrol 2 auxiliary s 2 ontrol s 2 auxiliary s -H (48 x 48 mm) odel Number Legend Controllers E5AN/E5EN-@@@@@@@@-@ Type H: Advaned 2. Control ode Blank: Standard or heating/ooling ontrol P: Position-proportional ontrol 3. Control Output A: Control Output Unit R: S: SSR 4. Control Output 2 A: Control Output Unit R: S: SSR 5. Auxiliary Outputs 2: Two s 3: Three s 6. Option Blank: None H: Heater burnout/ssr failure/heater overurrent detetion (CT) HH: Heater burnout/ssr failure/heater overurrent detetion (CT2) 7. Option 2 B: Two event s BF: Event + Transfer Option Units E53-@. Funtion EN: RS-232C ommuniations EN2: RS-422 ommuniations EN3: RS-485 ommuniations AKB: Event Output Units E53-@@ 2. Control Output R: Q: Q3: + 24 VDC (NPN) Q4: + 24 VDC (PNP) C3: + 4 to 2 ma DC C3D: + to 2 ma DC V34: Linear voltage + to VDC V35: Linear voltage + to 5 VDC 2. Version Blank: Available for E5AN-H/E5EN-H and E5AK/E5EK. N: Available only for E5AN-H/E5EN-H. 8. Option 3 : Option Unit an be mounted. 9. Power Supply Voltage Blank: to 24 VAC D: 24 VAC/VDC.Case Color Blank: Blak W: Silver.Terminal Cover -5: With Terminal Cover This data sheet is provided as a guideline for seleting produts. Be sure to refer to the following user manuals for appliation preautions and other information required for operation before attempting to use the produt. -H/E5AN-H/E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H57) -H/E5AN-H/E5EN-H Digital Controllers anual Advaned Type (Cat. No. H59) 44

45 Ordering Information E5AN-H Size /4 DIN (W H D) Case olor Blak Silver Power supply voltage to 24 VAC 24 VAC/ VDC Control method Basi Auxiliary 2 3 Valve 2 Basi 2 3 Valve 2 Control /2 Heater burnout Control Output Unit 2 2 SSR s 2 2 Control Output Unit SSR s Control Output Unit 2 2 SSR s 2 2 s 2 2 s 2 2 Control Output Unit 2 2 SSR s 2 2 Control Output Unit SSR s Control Output Unit 2 2 SSR s 2 2 s 2 2 s VAC Basi Control Output Unit to Control Output Unit VAC/ VDC Control Output Unit 2 2 Event s Optional funtions Transfer 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA R 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA E5AN-H/E5EN-H odel E5AN-HAA2HB-5 E5AN-HSS2HB-5 E5AN-HAA2HHBF-5 E5AN-HSS2HHBF-5 E5AN-HAA3BF-5 E5AN-HSS3BF-5 E5AN-HPRR2B-5 E5AN-HPRR2BF-5 E5AN-HAA2HBD-5 E5AN-HSS2HBD-5 E5AN-HAA2HHBFD-5 E5AN-HSS2HHBFD-5 E5AN-HAA3BFD-5 E5AN-HSS3BFD-5 E5AN-HPRR2BD-5 E5AN-HPRR2BFD-5 E5AN-HAA2HB-W-5 E5AN-HAA2HHBF-W-5 E5AN-HAA2HBD-W-5 -U (48 x 48 mm) -H (48 x 48 mm) 45

46 E5AN-H/E5EN-H -U (48 x 48 mm) -H (48 x 48 mm) E5EN-H Size /8 DIN (W H D) Case olor Blak Silver Power supply voltage to 24 VAC 24 VAC/ VDC Control method Basi Aessories (Order Separately) Output Units USB-infrared Conversion Cable Auxiliary 2 3 Valve 2 Basi 2 3 Valve 2 Control /2 Heater burnout Control Output Unit 2 2 SSR s 2 2 Control Output Unit SSR s Control Output Unit 2 2 SSR s 2 2 s 2 2 s 2 2 Control Output Unit 2 2 SSR s 2 2 Control Output Unit SSR s Control Output Unit 2 2 SSR s 2 2 s 2 2 s VAC Basi Control Output Unit to Control Output Unit VAC/ VDC Output unit odel Speifiations Relay Voltage (for driving SSR) Current Linear voltage E53-RN E53-QN E53-Q3 E53-Q4 E53-C3N E53-C3DN E53-V34N E53-V35N Control Output Unit 2 2 ST-NO, 25 VAC, 5 A (resistive load), eletrial life:, operations 2 VDC (PNP), max. load urrent: 4-mA, with short-iruit protetion 24 VDC (NPN), max. load urrent: 2-mA, with short-iruit protetion 24 VDC (PNP), max. load urrent: 2-mA, with short-iruit protetion 4 to 2-mA DC, load: 6 Ω max., resolution: approx., to 2-mA DC, load: 6 Ω max., resolution: approx., to VDC, load: kω min., resolution: approx., to 5 VDC, load: kω min., resolution: approx., odel E58-CIFIR Event s Optional Funtions Transfer 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA USB-Serial Conversion Cable Terminal Cover Connetable models E5AN-H E5EN-H 4 to 2-mA R 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA 4 to 2-mA Note: The Terminal Cover omes with the -@@@-5 models. Waterproof Paking Connetable models E5AN-H E5EN-H odel E58-CIFQ Note: The Waterproof Paking is inluded with the Controller. Current Transformers (CTs) C-Thermo Support Software odel E5EN-HAA2HB-5 E5EN-HSS2HB-5 E5EN-HAA2HHBF-5 E5EN-HSS2HHBF-5 E5EN-HAA3BF-5 E5EN-HSS3BF-5 E5EN-HPRR2B-5 E5EN-HPRR2BF-5 E5EN-HAA2HBD-5 E5EN-HSS2HBD-5 E5EN-HAA2HHBFD-5 E5EN-HSS2HHBFD-5 E5EN-HAA3BFD-5 E5EN-HSS3BFD-5 E5EN-HPRR2BD-5 E5EN-HPRR2BFD-5 E5EN-HAA2HB-W-5 E5EN-HAA2HHBF-W-5 E5EN-HAA2HBD-W-5 odel E53-COV6 odel Y92S-P4 Y92S-P5 Hole diameter odel 5.8 dia. E54-CT 2. dia. E54-CT3 odel EST2-2C-V4 46

47 Speifiations Ratings Power supply voltage Operating voltage range Power onsumption Sensor Input impedane Control method Control Linear voltage Built-in SSR Auxiliary Event Logi operations Transfer s R for position-proportional ontrol Number of s Output speifiations Number of s External ontat speifiations Number of operations Operations Output Setting method Work bit assignment Number of s No D in model number: to 24 VAC, 5/6 Hz D in model number: 24 VAC, 5/6 Hz; 24 VDC 85% to % of rated supply voltage to 24 VAC: 2 VA 24 VAC/VDC: 8.5 VA (24 VAC)/5.5 W (24 VDC) Any of the following an be seleted. Thermoouple: K, J, T, E, L, U, N, R, S, B, W, or PL II Platinum resistane thermometer: Pt or JPt Current : 4 to 2 ma or to 2 ma Voltage : to 5 V, to 5 V, or to V E5AN-H/E5EN-H Current : 5 Ω max., Voltage : Ω min. (Use a : onnetion when onneting the ES2-HB.) / ontrol or 2-PID ontrol (with auto-tuning) Output Unit (Install the Output Unit (sold separately).) 75 to 25 VAC, A (resistive load) : Open and lose: ST-NO, 25 VAC, A (inluding in-rush urrent), eletrial life:, operations min. Potentiometer : ust be between Ω and 2.5 kω for maximum open position. 2 or 3 max. : ST-NO, 25 VAC, 3 A (resistive load), eletrial life:, operations, minimum appliable load: 5 V, ma 2 or 4 (with an E53-AKB) Contat : : kω max., : kω min. Non-ontat : : Residual voltage:.5 V max., : Leakage urrent:. ma max. Current flow: Approx. 7 ma per ontat 8 max. Logi operation: Any of the following four patterns an be seleted. The status may be inverted. (A and B) or (C and D), (A or C) and (B or D), A or B or C or D, A and B and C and D (A, B, C, and D are four s.) Delay: delay or delay for the results of the logi operation given above. Setting time: to 9999 s or to 9999 min Output inversion: Possible One work bit per operation Any of The following an be assigned to up to eight work bits (logi operation results): Event operations, auxiliary s, or ontrol s. max. (Depends on model. odels with transfer (F in model number) Output speifiations : 4 to 2 ma DC, Load: 6 Ω max., Resolution at 4 to 2 ma: Approx., Number of s Signal type Current : 4 to 2 ma ( impedane: 5 Ω ±%) Analog saling Auray Indiation method Bank swithing Input sampling period Saling of signal to engineering units (EU) 9,999 to 3, (display: 3, max.) (±.2% of FS) ± digit max. 6 ms Set digitally using keys on the front panel or by using the R. -segment digital display and individual indiators (7-segments displays also possible) Charater height: E5AN-H: PV: 5.8 mm, SV: 9.5 mm, V: 6.8 mm; E5EN-H: PV:.8 mm, SV: 8. mm, V: 5.8 mm Content of 3-level display: PV/SV/V, PV/SV/Bank No., or soak time remain Number of digits: 5 for PV and SV, 4 for V Supported (number of banks: 8) Loal, alarm settings, PID sets (PID onstants, V upper limit, V lower limit, et.) anual, heating/ooling ontrol, loop burnout alarm, ramp, other alarm funtions, heater burnout detetion, 4% AT, % AT, V limiter, digital filter, self-tuning, temperature shift, run/stop, protetion funtions, Other funtions ontrol / ounter, extration of square root, V hange rate limit, PV/SV status display, logi operations, automati ooling oeffiient adjustment Ambient operating temperature to 55 C (with no ondensation or iing), for 3-year warranty: to 5 C Ambient operating humidity 25% to 85% Storage temperature 25 to 65 C (with no ondensation or iing) -U (48 x 48 mm) -H (48 x 48 mm) 47

48 E5AN-H/E5EN-H -U (48 x 48 mm) -H (48 x 48 mm) Input Ranges Thermoouple/Platinum Resistane Thermometer (Fully Universal Inputs) Temperature range ( C) Input type Platinum resistane thermometer Thermoouple Name Pt JPt K J T E L U N R S B W PL II 4 to 2 m A Analog Usable in the following ranges by saling: to 324, to 324., to 324., or to Setting number Shaded settings are the default settings. The appliable standards for the types are as follows: K, J, T, E, N, R, S, B: JIS C , IEC 584- L: Fe-CuNi, DIN U: Cu-CuNi, DIN W: W5Re/W26Re, AST E to 2 m A JPt: JIS C , JIS C Pt: JIS C , IEC 75 PL II: Aording to Platinel II eletromotive fore harts from BASF (previously Engelhard) to 5V to 5V to V 48

49 E5AN-H/E5EN-H Alarm Outputs Eah alarm an be independently set to one of the following 5 alarm types. The default is 2: Upper limit. Auxiliary s are alloated for alarms. delays and delays ( to 999 s) an also be speified. Note: For models with heater burnout, SSR failure, and heater overurrent detetion, alarm will be an OR of the alarm seleted from the following alarm types and the alarms for heater burnout, SSR failure, and heater overurrent. To only a heater burnout alarm, SSR failure alarm, and heater overurrent alarm for alarm, set the alarm type to (i.e., no alarm funtion). Set value Alarm type Alarm funtion Upper- and lowerlimit 2 Upper limit 3 Lower limit Upper- and lowerlimit range Upper- and lowerlimit with standby sequene 5 Upper-limit with standby sequene Lower-limit with standby sequene Absolute-value upper-limit Absolute-value lower-limit Absolute-value upper-limit with standby sequene Absolute-value lower-limit with standby sequene LBA (for alarm only) PV hange rate alarm R absolute value upper limit 6 R absolute value lower limit 6 Alarm operation When is positive Output L L L H H H When is negative.with set values, 4 and 5, the upper and lower limit values an be set independently for eah alarm type, and are expressed as L and H. 2. Set value:, Upper- and lower-limit alarm Case L H H <, L > H < L Case 2 L H H >, L < H > L 3. Set value: 4, Upper- and lower-limit range Case L H H <, L > H < L Case 2 L H H >, L < H > L Case 3 (Always ) 4. Set value: 5, Upper- and lower-limit with standby sequene For Upper- and Lower-Limit Alarm Desribed Above Case and 2 Always when the upper-limit and lower-limit hysteresis overlaps. Case 3: Always 5. Set value: 5, Upper- and lower-limit with standby sequene Always when the upper-limit and lower-limit hysteresis overlaps. 6. Displayed when there is a remote. H H L H L L Case 3 (Always ) H H L H L L H <, L < H <, L > H L H >, L < H L H <, L < H <, L > H L H >, L < H L -U (48 x 48 mm) -H (48 x 48 mm) 49

50 E5AN-H/E5EN-H -U (48 x 48 mm) -H (48 x 48 mm) Charateristis Thermoouple: (±.% of indiated value or ± C, whihever is greater) ± digit max. Platinum resistane thermometer: (±.% of indiated value or ±.5 C, whihever is greater) ± digit max. Indiation auray Analog : ±.% FS ± digit max. CT : ±5% FS ± digit max. Potentiometer : ±5% FS ± digit max. Transfer auray ±.3% FS max. Influene of temperature 2 Influene of voltage 2 Input sampling period Hysteresis Thermoouple (R, S, B, W, PL II): (±% of PV or ± C, whihever is greater) ± digit max. Other thermoouple : (±% of PV or ±4 C, whihever is greater) ± digit max. 3 Platinum resistane thermometer: (±% of PV or ±2 C, whihever is greater) ± digit max. Analog : (±%FS) ± digit max. 6 ms Temperature :. to 324. C or F (in units of. C or F) Analog :.% to 99.99% FS (in units of.% FS) Proportional band (P) Temperature :. to 324. C or F (in units of. C or F) Analog :.% to 999.9% FS (in units of.% FS) Integral time (I). to 324. s (in units of. s) Derivative time (D). to 324. s (in units of. s) Control period.5, to 99 s (in units of s) anual reset value. to.% (in units of.%) Alarm setting range Affet of signal soure resistane Insulation resistane 9999 to 324 (deimal point position depends on type) Thermoouple:. C/Ω max. ( Ω max.) Platinum resistane thermometer:. C/Ω max. ( Ω max.) 2 Ω min. (at 5 VDC) Dieletri strength 2,3 VAC, 5 or 6 Hz for min (between terminals with different harge) Vibration alfuntion to 55 Hz, 2 m/s 2 for min eah in, Y, and Z diretions resistane Destrution to 55 Hz,.75-mm single amplitude for 2 hrs eah in, Y, and Z diretions Shok alfuntion m/s 2, 3 times eah in, Y, and Z diretions resistane Destrution 3 m/s 2, 3 times eah in, Y, and Z diretions Weight E5AN-H E5EN-H Degree of protetion emory protetion Setup Tool Setup Tool port Standards EC Approved standards Conformed standards Controller: Approx. 3 g, ounting Braket: Approx. g Controller: Approx. 26 g, ounting Braket: Approx. g Front panel: IP66, Rear ase: IP2, Terminals: IP Non-volatile memory (number of writes:,, times) C-Thermo version 4. or higher Provided on the bottom of the E5AN-H and E5EN-H. An E58-CIFQ USB-Serial Conversion Cable is required to onnet the omputer to the E5AN-H and E5EN-H. Provided on the front of the E5AN-H and E5EN-H. An E58-CIFIR USB-infrared Conversion Cable is required to onnet the omputer to the E5AN-H or E5EN-H. 4 UL 6-, CSA C22.2 No. - EN 6- (IEC 6-): Pollution level 2, overurrent ategory II EI: EN 6326 Radiated Interferene Eletromagneti Field Strength: EN 55 Group, lass A Noise Terminal Voltage: EN 55 Group, lass A ES: EN 6326 ESD Immunity: EN Eletromagneti Field Immunity: EN Burst Noise Immunity: EN Conduted Disturbane Immunity: EN Surge Immunity: EN Power Frequeny agneti Field Immunity: EN Voltage Dip/Interrupting Immunity: EN The indiation auray of K thermoouples in the 2 to 3 C range, T and N thermoouples at a temperature of C max., and U and L thermoouples at any temperatures is ±2 C ± digit max. The indiation auray of the B thermoouple at a temperature of 4 C max. is not speified. The indiation auray of B thermoouples in the 4 to 8 C range is ±3 C max. The indiation auray of the R and S thermoouples at a temperature of 2 C max. is ±3 C ± digit max. The indiation auray of W thermoouples is ±.3% of PV or ±3 C, whihever is greater, ± digit max. The indiation auray of PL II thermoouples is ±.3% of PV or ±2 C, whihever is greater, ± digit max. 2. Ambient temperature: C to 23 C to 55 C, Voltage range: 5% to % of rated voltage 3. K thermoouple at C max.: ± C max. 4. External ommuniations (RS-232C, RS-485, or RS-422) and able ommuniations for the Setup Tool an be used at the same time. 5

51 E5AN-H/E5EN-H USB-Serial Conversion Cable Appliable OS Appliable software Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher Appliable models E5AN/E5EN//-U/ E5AN-H/E5EN-H/-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Setup Tool port (on bottom of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 7 ma Ambient operating humidity % to 8% to 55 C (with no ondensation or iing) Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Speifiations Transmission line onnetion method Synhronization method Protool Baud rate Transmission ode Data bit length Stop bit length Error detetion Flow ontrol Interfae Retry funtion buffer response wait time 2, m max. Approx. g RS-485, RS-422: ultipoint RS-232C: Point-to-point RS-485 (two-wire, half duplex) RS-422 (four-wire, half duplex) or RS-232C Start-stop synhronization CompoWay/F, SYSWAY, or odbus 2, 24, 48, 96, 92, 384, or 576 bps ASCII (CompoWay/F, SYSWAY) RTU (odbus) 7 or 8 bits or 2 bits Vertial parity (none, even, odd) Frame hek sequene (FCS) with SYSWAY Blok hek harater (BCC) with CompoWay/F or CRC-6 odbus None RS-485, RS-422, or RS-232C None 27 bytes to 99 ms Default: 2 ms Note: The baud rate, data bit length, stop bit length, and vertial parity an be individually set using the Setting Level. Current Transformer (Order Separately) Ratings Dieletri strength, VAC for min Vibration resistane 5 Hz, 98 m/s 2 Weight E54-CT: Approx..5 g, E54-CT3: Approx. 5 g Aessories (E54-CT3 only) Armatures (2) Plugs (2) USB-Infrared Conversion Cable Appliable OS Appliable software Appliable models Windows 2, P, or Vista Thermo ini, C-Thermo version 4. or higher E5AN-H/E5EN-H USB interfae standard Conforms to USB Speifiation.. DTE speed Connetor speifiations Power supply Power supply voltage Current onsumption Ambient operating temperature 384 bps Computer: USB (type A plug) Temperature Controller: Infrared port (on front of Controller) Bus power (Supplied from USB host ontroller.) 5 VDC 8 ma Ambient operating humidity % to 8% to 55 C (with no ondensation or iing) Storage temperature 2 to 6 C (with no ondensation or iing) Storage humidity % to 8% Altitude Weight Note: A driver must be installed in the personal omputer. Refer to installation information in the operation manual for the Conversion Cable. Heater Burnout Alarms, SSR Failure Alarms, and Heater Overurrent Alarms CT (for heater urrent detetion) aximum heater urrent Input urrent indiation auray Heater burnout alarm setting range SSR failure alarm setting range 2 Heater overurrent alarm setting range 3 2, m max. Approx. 3 g (with mounting adaptor) odels with detetion for single-phase heaters: One odels with detetion for single-phase or three-phase heaters: Two s 5 A AC ±5% FS ± digit max.. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. to 49.9 A (in units of. A) inimum detetion time: ms. For heater burnout alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is lower than the set value (i.e., heater burnout detetion urrent value). 2. For SSR failure alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., SSR failure detetion urrent value). 3. For heater overurrent alarms, the heater urrent will be measured when the ontrol is, and the assigned to the alarm funtion will turn if the heater urrent is higher than the set value (i.e., heater overurrent detetion urrent value). -U (48 x 48 mm) -H (48 x 48 mm) 5

52 E5AN-H/E5EN-H -U (48 x 48 mm) -H (48 x 48 mm) Eletrial Life Expetany Curve for Relays (Referene Values) Life ( 4 operations) E5AN-H/E5EN-H 25 VAC, 3 VDC (resistive load) osφ = Swithing urrent (A) SSR Outputs (OUT/OUT2) Ratings Rated load voltage: 75 to 25 VAC Rated load urrent: A (resistive load) Note:. The load urrent must be within the derating urve. 2. There is no zero-ross funtion. Derating Curve for SSR Outputs (Referene Values) Load urrent I (A) OUT/OUT Condition A Condition B Ambient temperature ( C) Condition A: SSR s % Condition B: SSR s 5% with 2-s ontrol yle 52

53 External Connetions E5AN-H/E5EN-H A voltage (ontrol, for driving SSR) is not eletrially insulated from the internal iruits. When using a grounding thermoouple, do not onnet any of the ontrol terminals to ground. If the ontrol terminals are onneted to ground, errors will our in the measured temperature values as a result of leakage urrent. The voltage (ontrol 2, for driving SSR) has basi insulation provided for the internal iruit Controllers to 24 VAC 24 VAC/VDC (no polarity) Control s, 2 Output Unit Control s, 2 Relay Outputs 25 VAC, 5 A (resistive load) SSR Outputs 75 to 25 VAC, A (resistive load) odels with Positionproportional Control 25 VAC, A (inluding inrush urrent) Auxiliary s, 2 ST-NO, 25 VAC, 3 A (resistive load) Input power supply Control Control 2 Auxiliary 2 Auxiliary EV3 DO NOT EV Transfer to 2 ma DC (Load: 6 Ω max.) 29 Remote 4 to 2 ma DC 3 Event Inputs Potentiometer Note: Wire all voltage terminals orretly. The Controller may fail if voltage terminals are wired inorretly. EV2 CT2 Option Units CT CT2 DO NOT DO NOT E53-EN RS-232C SD 2 RD 3 SG 2 DO NOT 22 DO NOT EV O W C DO NOT A B B DO NOT DO NOT E53-EN2 RS V RDB RDA SG SDB SDA Auxiliary 3 DO NOT ma DO NOT E53-EN3 RS B (+) A ( ) DO NOT B (+) A ( ) E53-AKB Auxiliary 3 DT, 25 VAC, 3 A (resistive load) Event Inputs EV2 A heater burnout alarm, SSR failure, heater overurrent alarm, or alarm is sent to the to whih the alarm funtion is assigned. EV -U (48 x 48 mm) -H (48 x 48 mm) 53

54 E5AN-H/E5EN-H Nomenlature -U (48 x 48 mm) E5AN-H Operation indiators Temperature unit SUB SUB2 SUB3 HA PV No. display E5EN-H Operation indiators Temperature unit SUB SUB2 HA SUB3 PV No. display SV No.2 display SV No.2 display R Programmable Funtion Key/ Auto/anual Key PF A/ E5AN-H OUT OUT2 R STOP CW ANU Ir V No.3 display Up Key Down Key Operation indiators ode Key Level Key OUT STOP OUT2 CW ANU E5EN-H Ir PF A/ V No.3 display Up Key Programmable Funtion Key/ Auto/anual Key Level Key ode Key Down Key -H (48 x 48 mm) Dimensions E5AN-H ounted Separately Group ounted (96 number of units 3.5) +. (Unit: mm) min Group mounting does not allow waterproofing. Reommended panel thikness is to 8mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) To mount the Controller so that it is waterproof, insert the waterproof paking onto the Controller. When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. Waterproof Paking (Aessory) ounting Braket (Aessory) Terminal Cover (E53-COV6) (Aessory) Crimp terminal size: 3.5 Group mounting is not possible if an SSR is used for ontrol or 2 and the E53-C3N or E53-C3DN Output Unit is used. For these ombinations, maintain the following mounting spae between Controllers. 2 min min

55 E5AN-H/E5EN-H E5EN-H ounted Separately Group ounted (48 number of units 2.5) U (48 x 48 mm) 2 min. Group mounting does not allow waterproofing Waterproof Paking (Aessory) ounting Braket (Aessory) 9 Terminal Cover (E53-COV6) (Aessory) Crimp terminal size: Reommended panel thikness is to 8 mm. Group mounting is not possible in the vertial diretion. (aintain the speified mounting spae between Controllers.) When two or more Controllers are mounted, make sure that the surrounding temperature does not exeed the allowable operating temperature speified in the speifiations. Group mounting is not possible if an SSR is used for ontrol or 2 and the E53-C3N or E53-C3DN Output Unit is used. For these ombinations, maintain the following mounting spae between Controllers. 2 min min H (48 x 48 mm) 55

56 E5AN-H/E5EN-H Aessories (Order Separately) -U (48 x 48 mm) USB-Infrared Conversion Cable E58-CIFIR USB-Infrared Conversion Cable USB onnetor (type A plug) (2,) dia LED indiator: RD LED indiator: SD ounting Adapter With ounting Adapter Conneted H (48 x 48 mm) ounting Adapter (Aessory) USB-Serial Conversion Cable E58-CIFQ (75) (2,) 25 LED indiator: SD,765 USB onnetor (type A plug) LED indiator: RD Serial onnetor Terminal Covers E53-COV6 (Six Covers provided.)

57 E5AN-H/E5EN-H Waterproof Paking Y92S-P4 (for DIN 96 96) Current Transformers E54-CT E54-CT3 E54-CT3 Aessory Armature Approx. 3 dia. Plug Approx. 6 dia. (22) Y92S-P5 (for DIN 48 96) Plug dia..5 Two, 3.5 dia. 2 dia. Connetion Example Two, 3 (depth 4) Armature dia. Lead Order the Waterproof Paking separately if it beomes lost or damaged. The Waterproof Paking an be used to ahieve an IP66 degree of protetion. (Deterioration, shrinking, or hardening of the waterproof paking may our depending on the operating environment. Therefore, periodi replaement is reommended to ensure the level of waterproofing speified in IP66. The time for periodi replaement depends on the operating environment. Be sure to onfirm this point at your site. Consider one year a rough standard. OR shall not be liable for the level of water resistane if the ustomer does not perform periodi replaement.) The Waterproof Paking does not need to be attahed if a waterproof struture is not required. E54-CT Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 5 A (5/6 Hz) Number of windings: 4±2 Winding resistane: 8±2 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω Ω RL = Ω Distortion fator % 3% % ma, A Thru-urrent (Io) A (r.m.s.) E54-CT3 Thru-urrent (Io) vs. Output Voltage (Eo) (Referene Values) aximum ontinuous heater urrent: 2 A (5/6 Hz) (aximum ontinuous heater urrent for an OR Temperature Controller is 5 A.) Number of windings: 4±2 Winding resistane: 8±.8 Ω Output voltage (Eo) V (r.m.s.) V 5 Hz mv µv kω 5 Ω Ω 5 Ω RL = Ω Distortion fator % 3% % ma, A Thru-urrent (Io) A (r.m.s.) -U (48 x 48 mm) -H (48 x 48 mm) 57

58 -U (48 x 48 mm) E5@N/E5@N-H Operation Setting Levels Diagram This diagram shows all of the setting levels. To move to the advaned funtion setting level and alibration level, you must enter passwords. Some parameters are not displayed depending on the protet level setting and the onditions of use. Control stops when you move from the operation level to the initial setting level. Basi Type Start in manual mode. Power Start in automati mode. -H (48 x 48 mm) E5EN-H(48 x 96 mm) anual mode Level hange. You an return to the operation level by exeuting a software reset. 2. It is not possible to move to other levels from the alibration level by operating the keys on the front panel. It an be done only by first turning the power. 3. From the manual ontrol level, key operations an be used to move to the operation level only. 4. When the PF Setting parameter is set to A- for a Controller with a PF Key (E5AN/E5EN). 5. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN/E5EN) Error Displays (Troubleshooting) When an error ours, the No. display shows the error ode. Take neessary measure aording to the error ode, referring the table below. No. display eaning Ation s.err (S. Err) e333 (E333) e (E) 3 anual Control Level Press the O Key or the PF Key for at least s. 4 a-m Input error A/D onverter error emory error Press the O Key for at least 3 s while a-m is displayed. (a-m will flash after st seond.) 4 Press the PF Key for at least s. Control stops. Press the O Key for at least s. Operation Level * Press the O Key for at least s. PF Key 5 Initial Setting Level Adjustment Level Press the O Key less than s. onitor/setting Item Level Chek the wiring of s for miswiring, disonnetions, and short-iruits and hek the type. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise. Advaned Funtion Setting Level Calibration Level Status at error Control Alarm Operates as above the upper limit. Note: If the value exeeds the display limit ( 999 to 9999), though it is within the ontrol range, will be displayed under 999 and above Under these onditions, ontrol and alarm will operate normally. For details on the ontrol range, refer to the /E5AN/E5EN Digital Temperature Controllers User's anual Basi Type (Cat. No. H56). These errors are displayed only when the PV/ is displayed. Errors are not displayed for other displays. 25 Input password while amov is displayed. (Set value 69) Input password. Press the O Key for at least 3 s. (Display will flash after st seond.) Setting Level Press the O Key for less than s. 2 PF Key 5 Press the O+ Keys for at least 3 s. (Display will flash after st seond.) 25 Control in progress Control stopped Protet Level Not displayed for some models Press the O+ Keys for at least s. Note: The time taken to move to the protet level an be adjusted by hanging the ove to protet level time setting. 58

59 Advaned Type anual mode. You an return to the operation level by exeuting a software reset. 2. It is not possible to move to other levels from the alibration level by operating the keys on the front panel. It an be done only by first turning the power. 3. From the manual ontrol level, key operations an be used to move to the operation level only. 4. When the PF Setting parameter is set to A- for a Controller with a PF Key (E5AN-H/E5EN-H). 5. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN-H/E5EN-H) Error Displays (Troubleshooting) When an error ours, the No. display shows the error ode. Take neessary measure aording to the error ode, referring the table below. No. display eaning Ation s.err (S. Err) e333 (E333) e (E) Start in manual mode. Press the O Key or the PF Key for at least s. 4 3 anual Control Level a-m Input error A/D onverter error emory error Start in automati mode. Press the O Key for at least 3 s while a-m is displayed. (a-m will flash after st seond.) Press the PF Key for at least s. 4 Control stops. Press the O Key for at least s. Power Operation Level Press the O Key for at least s. PF Key 5 Initial Setting Level Press the O Key less than s. Press the O Key less than s. PID Setting Level onitor/setting Item Level 25.. Advaned Funtion Setting Level Calibration Level Press the O Key less than s. Input password while amov is displayed. (Set value 69) Input password. Adjustment Level PF Key 5 Press the O Key for at least 3 s. (Display will flash after st seond.) Setting Level Press the O Key for less than s. Press the O + Keys for at least 3 s. (Display will flash after st seond.) Control in progress Control stopped Level hange Chek the wiring of s for miswiring, disonnetions, and short-iruits and hek the type. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise. Turn the power then bak again. If the display remains the same, the ontroller must be repaired. If the display is restored to normal, then a probable ause an be external noise affeting the ontrol system. Chek for external noise Protet Level Not displayed for some models Control Status at error Alarm Note: If the value exeeds the display limit ( 9999 to 324), though it is within the ontrol range, will be displayed under 9999 and above 324. Under these onditions, ontrol and alarm will operate normally. For details on the ontrol range, refer to the -H/E5AN-H/E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H57). These errors are displayed only when the PV/ is displayed. Errors are not displayed for other displays. 2 Press the O Key less than s. Bank Setting Level Note: The time taken to move to the protet level an be adjusted by hanging the ove to protet level time setting. Press the O+ Keys for at least s. Operates as above the upper limit. -U (48 x 48 mm) -H (48 x 48 mm) E5EN-H(48 x 96 mm) Operation Safety Preautions 59

60 -U (48 x 48 mm) -H (48 x 48 mm) E5EN-H(48 x 96 mm) Parameters Basi Type Some parameters are not displayed depending on the model of the Controller and parameter settings. For details, refer to the /E5AN/E5EN Digital Temperature Controllers User's anual Basi Type (Cat. No. H56). Adjustment Level l.adj at mwt t Heater Current Value onitor. hb Heater Burnout Detetion. o Heater Overurrent Detetion 5. t2. hb2. o2 5. lr. hs 5. lr2. hs2 5. sp- C sp- sp-2 sp-3 C Adjustment Level Display Displayed only one when entering adjustment level. AT Exeute/Canel Writing Heater Current 2 Value onitor Heater Burnout Detetion 2 Heater Overurrent Detetion 2 Leakage Current onitor HS Alarm Leakage Current 2 onitor HS Alarm 2 used by multi- C 2 C 3 Press the PF Key for at least s. Press the O Key less than s. Press the O Key less than s. C ins. insh C C Upper Limit Temperature. Input Shift Value 2-point shift insl. C p 8. i 233 d 4 -s. -db. C anual Reset Value of-r Clear the set during 5. stabilization of P or PD ontrol. C hys Hysteresis (Heating). hys. soak wt-b mv-s. mv-e. C sprt C C ol-h 5. ol-l -5. orl. sqrp. Temperature Input Shift Starting in manual mode. -point shift Lower Limit Temperature Input Shift Value Proportional Band Integral Time PID settings Derivative Time Cooling Coeffiient Heating/ooling Dead Band Hysteresis settings Hysteresis (Cooling) Soak Time Wait Band V at Stop V at PV Error Ramp Set Value V Upper Limit V Lower Limit V Change Rate Limit Set either of these parameters. Extration of Square Root Low-ut Point 25 pmov oapt ipt wtpt pfpt PF Key Protet Restrits PF key operation (E5AN/E5EN only) pmsk on prlp Password to ove to Protet Level: Password setting a-m m-sp C sp-m t. lr2 sktr Set Point During Ramp t2 Heater Current 2 Value onitor. lr. Leakage Current 2 onitor. prst rset Power anual Control Level C PV/V Press the O Key for at least 3 s. C C PID Control only Press the O and Keys for at least 3 s. Press the O Key or the PF Key for at least s. Starting in automati mode. Operation Level Proess Value Added when Additional PV display is. Proess Value/ Set Point Auto/anual Swith PID ontrol only. Added when auto/manual selet addition is. ulti- Set Point Setting Heater Current Value onitor Leakage Current onitor Program Start Soak Time Remain Protet Level Note: The time taken to move to the protet level an be adjusted by hanging the "ove to protet level time" setting. ove to Protet Level: Displayed only when a password is set. Restrits moving to protet level. Operation/Adjustment Protet: Restrits displaying and modifying menus in operation, adjustment, and manual ontrol levels. Initial Setting/ Protet: This protet level restrits movement to the initial setting, ommuniations setting, and advaned funtion setting levels. Setting Change Protet: Protets hanges to setups by operating the front panel keys. Parameter ask Enable: Displayed only when a parameter mask is set. r-s run al- alh C C C all C al-2 C al2h C al2l C al-3 C al3h C al3l -o. Alarm Value Upper Limit o. Press the O and Keys for at least s. Setting Level psel Protool Setting: Swithes between wf CompoWay/F (SYSWAY) and odbus. Unit No. u-no bps 9.6 len sbit 2 prty even sdwt 2 RUN/STOP Alarm Value Alarm Value Lower Limit Alarm Value 2 Alarm Value Upper Limit 2 Alarm Value Lower Limit 2 Alarm Value 3 Alarm Value Upper Limit 3 Alarm Value Lower Limit 3 Set either of these parameters. Set either of these parameters. Set either of these parameters. V onitor (Heating) V onitor (Cooling) Data Length 7 Press the O Key less than s. Note: Displayed only for models with ommuniations. Changes are effetive after yling power or after a software reset. Baud Rate CompoWay/F (SYSWAY) only Stop Bits Parity Send Data Wait Time PF Key 2 Press the O Key for at least 3 s. PF Key 2 Other than the Auto/anual Swith display Press the O Key for at least s. Initial Setting Level Press the O Key less than s. in-t 5 in-h in-l C C dp d-u sl-h 3 sl-l -2 ntl onof Standard or s-h Heating/Cooling stnd st on ptrn p -p 2 ST (Self-tuning) Control Period (Heating) 2 Set the / yle. Control Period (Cooling) orev or-r alt 2 alh.2 C Input Type Saling Upper Limit Saling Lower Limit Deimal Point For type of analog Temperature Unit C, F Upper Limit Lower Limit PID / For type of temperature Limit the set point For type of temperature, standard ontrol, or PID Program Pattern When assigning PID or ontrol to / Diret/Reverse Operation Alarm Type Alarm Hysteresis. When the PF Setting parameter is set to A- for a Controller with a PF Key (E5AN/E5EN). 2. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN/E5EN). 6

61 onitor/setting Item Level C 25 onitor/setting Item Display (E5AN/E5EN only) PF onitor/setting PF onitor/setting PF onitor/setting PF Item Display 2 Item Display 3 Item Display 4 Note: The monitor/setting items to be displayed is set in the onitor/setting Item to 5 parameters (advaned funtion setting level). onitor/setting Item Display 5 -U (48 x 48 mm) Press the O Key for at least s. Advaned Funtion Setting Level alt2 2 C alh2.2 alt3 2 C alh3.2 tr-t Transfer Output tr-h Upper Limit. tr-l Transfer Output Lower Limit. o-t 4-2 ev-m Alarm 2 Type Alarm 2 Hysteresis Alarm 3 Type Alarm 3 Hysteresis Transfer Output Type Linear Linear Current Output Linear Number of ulti- Uses Two s: Four s: 2 ev- Event Input Assignment none ev-2 Event Input Assignment 2 stop sqr Extration of Square Root Enable amov ove to Advaned Funtion Setting Level: Displayed when initial setting/ommuniations protet is set to. ove by setting password ( 69). init mspu spru m rest sbn n-o sb2n Standby Sequene Reset a Auxiliary Output 2 Open in Alarm n-o sb3n n-o C hbu on hbl hbh Heater Burnout Hysteresis. ST Stable Range st-b 5. α alfa.65 at-g.8 at-h.8 C lma 2. inf. pvad o-dp ret Automati Display Return Time Parameter Initialization ulti- Uses Ramp Time Unit Auxiliary Output Open in Alarm Auxiliary Output 3 Open in Alarm HB / Heater Burnout Lath AT Calulated Gain AT Hysteresis Limit Cyle V Amplitude Input Digital Filter Additional PV Display V Display alt a2lt a3lt prlt sero j on rlrv olr red C pv-b 5. aon a2on a3on aof a2of a3of istp ins mvse amad ove to Protet Level Time 3 Auto/anual Selet Addition rt Alarm Lath Alarm 2 Lath Alarm 3 Lath Input Error Output Cold Juntion Compensation ethod B Command Logi Swithing PV Change Color PV Stable Band Alarm Delay Alarm 2 Delay Alarm 3 Delay Alarm Delay Alarm 2 Delay Alarm 3 Delay Input Shift Type V at Stop and Error Addition RT C C hsu on hsl hsh. lba lbal 8. lbab 3. out o Control Output 2 out2 Assignment none sub Auxiliary Output Assignment alm sub2 alm2 sub3 Auxiliary Output 3 Assignment alm3 (E5AN/E5EN only) sel on t-u m alsp sp-m manl anual V Limit Enable pvrp 4 sa Automati Cooling Coeffiient Adjustment ou on ol Heater Overurrent Lath oh. HS Alarm Use HS Alarm Lath HS Alarm Hysteresis LBA Detetion Time LBA Level LBA Band Control Output Assignment Auxiliary Output 2 Assignment Charater Selet Soak Time Unit Alarm Seletion PV Rate of Change Calulation Period Heater Overurrent Use Heater Overurrent Hysteresis PF Setting pf (E5AN/E5EN only) a-m pfd pfd2 pfd3 pfd4 pfd5 spdp 4 odsl o pvdp on pvst PV Status Display Funtion svst SV Status Display Funtion d.ref.25 ram ra2m ra ra2 ra mov ove to Calibration Level onitor/setting Item (E5AN/E5EN only) onitor/setting Item 2 onitor/setting Item 3 onitor/setting Item 4 onitor/setting Item 5 "PV/" Display Sreen Seletion V Display Seletion PV Deimal Point Display Display Refresh Period Control Output / Count onitor Control Output 2 / Count onitor Control Output / Count Alarm Set Value Control Output 2 / Count Alarm Set Value / Counter Reset -H (48 x 48 mm) E5EN-H(48 x 96 mm) Operation Safety Preautions 6

62 -U (48 x 48 mm) Advaned Type Some parameters are not displayed depending on the model of the Controller and parameter settings. For details, refer to the -H/E5AN-H/ E5EN-H Digital Controllers User's anual Advaned Type (Cat. No. H57). Power anual Control Level Protet Level Operation Level Initial Setting Level Adjustment Level Setting Level Bank Setting Level PID Setting Level onitor/setting Item Level -H (48 x 48 mm) PID Setting Level Advaned Funtion Setting Level Press the O Key less than s. Bank Setting Level Press the O Key less than s. Press the O Key less than s. E5EN-H(48 x 96 mm) Display PID Seletion d.pid PID d.pid PID2 2 d.pid 3 PID3.p 8..i 233..d 4..olh 5..oll -5..aut 32..s..lba d.pid 8 8.p PID 8 Proportional Band 8. 8.i PID 8 Integral Time d PID 8 Derivative Time 4. 8.olh PID 8 V Upper Limit 5. 8.oll PID 8 V Lower Limit aut PID 8 Automati Seletion 32. Range Upper Limit 8.s PID 8 Cooling Coeffiient. 8.lba PID 8 LBA Detetion Time PID8 Display Bank Seletion d.bnk Bank d.bnk Bank d.bnk 2 Bank2.lsp..pid.spr.a-..ah..al..a-2..a2h..a2l..a-3..a3h..a3l..sok.wtb d.bnk 7 7.lsp. 7.pid 7.spr Bank 7 Ramp Set Value 7.a- Bank 7. Alarm Value Bank 7 7.ah Alarm Value. Upper Limit Bank 7 7.al. Bank7 Bank 7 Bank 7 PID Set No. Alarm Value Lower Limit Set either of these parameters 7.a-2 Bank 7. Alarm Value 2 Bank 7 7.a2h Alarm Value. Upper Limit 2 7.a2l. 7.a-3 Bank 7. Alarm Value 3 Bank 7 7.a3h Alarm Value. Upper Limit 3 Bank 7 Alarm Value Lower Limit 2 Bank 7 7.a3l Alarm Value. Lower Limit 3 Set either of these parameters Set either of these parameters 7.sok Bank 7 Soak Time 7.wtb Bank 7 Wait Band 62

63 Starting in manual mode. Power -U (48 x 48 mm) anual Control Level Adjustment Level Press the PF Key for at least s. Press the O Key less than s PV/V PID Control only Press the O Key or the PF Key for at least s. Operation Level Starting in automati mode. Press the O and Keys for at least 3 s. l.adj at mwt irda spmd lsp t Heater Current. Value onitor hb Heater Burnout. Detetion o Heater Overurrent 5. Detetion t2. hb2. o2 5. lr. hs 5. lr2. hs2 5. ins. insh Upper Limit Temperature. Input Shift Value 2-point shift insl. Adjustment Level Display Displayed only one when entering adjustment level. AT Exeute/Canel Writing Infrared Use ode Heater Current 2 Value onitor Heater Burnout Detetion 2 Heater Overurrent Detetion 2 Leakage Current onitor HS Alarm Leakage Current 2 onitor HS Alarm 2 Temperature Input Shift -point shift Lower Limit Temperature Input Shift Value Set either of these parameters. p 8. i 233. d 4. -s. -db. of-r 5. hys. hys. soak wt-b mv-s. mv-e. sprt ol-h 5. ol-l -5. orl. db Position Proportional Dead Band 2. o-h.8 sqrp. Proportional Band Integral Time Derivative Time PID settings Cooling Coeffiient Heating/ooling Dead Band anual Reset Value Clear the set during stabilization of P or PD ontrol. Hysteresis (Heating) Hysteresis settings Hysteresis (Cooling) Soak Time Wait Band V at Stop V at PV Error Ramp Set Value V Upper Limit V Lower Limit V Change Rate Limit Open/Close Hysteresis Extration of Square Root Low-ut Point Press the O Key for at least 3 s a-m bank rsp. sp-m. t Heater Current Value. onitor t2 Heater Current 2 Value. onitor lr. lr2. prst rset sktr 25. PF Key 2 Proess Value Added when Additional PV display is. Proess Value/ Set Point Auto/anual Swith PID ontrol only. Added when auto/manual selet addition is. Bank No. Remote onitor Set Point During Ramp Leakage Current onitor Leakage Current 2 onitor Program Start Soak Time Remain onitor/setting Item Display. PF PF r-s run al-. alh. all. al-2. al2h. al2l. al-3. al3h. al3l. o. -o. RUN/STOP Alarm Value Alarm Value Upper Limit Alarm Value Lower Limit Alarm Value 2 Alarm Value Upper Limit 2 Alarm Value Lower Limit 2 Alarm Value 3 Alarm Value Upper Limit 3 Alarm Value Lower Limit 3 v-m Valve Opening onitor. PF Set either of these parameters. Set either of these parameters. Set either of these parameters. V onitor (Heating) V onitor (Cooling) onitor/setting Item Level (E5AN-H/E5EN-H only) onitor/setting Item Display 4 onitor/setting Item Display 2 onitor/setting Item Display 5 Note: The monitor/setting items to be displayed is set in the onitor/setting Item to 5 parameters (advaned funtion setting level). PF Key 2 Press the O and Keys for at least s. onitor/setting Item Display 3 PF -H (48 x 48 mm) E5EN-H(48 x 96 mm) Operation Safety Preautions. When the PF Setting parameter is set to A- for a Controller with a PF Key (E5AN-H/E5EN-H). 2. When the PF Setting parameter is set to PFDP for a Controller with a PF Key (E5AN-H/E5EN-H). 63

64 -U (48 x 48 mm) E5@N/E5@N-H Press the O Key for at least s. Press the O Key for at least 3 s. Other than the Auto/anual Swith display Press the O Key less than s. Initial Setting Level -H (48 x 48 mm) E5EN-H(48 x 96 mm) pmov oapt ipt wtpt pfpt pmsk on prlp Protet Level The time taken to move to the protet level an be adjusted by hanging the "ove to protet level time" setting. ove to Protet Level: Displayed only when a password is set. Restrits moving to protet level. Operation/Adjustment Protet: Restrits displaying and modifying menus in operation, adjustment, and manual ontrol levels. Initial Setting/ Protet: This protet level restrits movement to the initial setting, ommuniations setting, and advaned funtion setting levels. Setting Change Protet: Protets hanges to setups by operating the front panel keys. PF Key Protet Restrits PF key operation (E5AN-H/E5EN-H only) Parameter ask Enable: Displayed only when a parameter mask is set. Password to ove to Protet Level: Password setting Press the O Key less than s. Setting Level Displayed only for models with ommuniations. Changes are effetive after yling power or after a software reset. psel wf u-no bps 9.6 len 7 sbit 2 prty even sdwt 2 Protool Setting: Swithes between CompoWay/F (SYSWAY) and odbus. Unit No. Baud Rate CompoWay/F (SYSWAY) only Data Length Stop Bits Parity Send Data Wait Time in-t 5 in-h in-l dp d-u sl-h 3. sl-l -2. ntl pid Standard or s-h Heating/Cooling stnd ST (Self-tuning) st on ptrn pbnk 7 p 2 -p 2 orev or-r alt 2 alh.2 Input Type Saling Upper Limit Saling Lower Limit Deimal Point For type of analog Temperature Unit C, F For type of temperature Upper Limit Limit the set point Lower Limit PID / For type of temperature, standard ontrol, or PID Program Pattern Valid Program Bank When assigning PID or ontrol to / Control Period (Heating) Set the / yle. Control Period (Cooling) Diret/Reverse Operation Alarm Type Alarm Hysteresis alt2 2 alh2.2 alt3 2 alh3.2 tr-t tr-h Transfer Output Upper Limit. tr-l. o-t 4-2 ev-b ev- Event Input Assignment none ev-2 stop ev-3 none ev-4 Event Input Assignment 4 none lfl flot alb mot 3 sqr Extration of Square Root Enable amov Alarm 2 Type Alarm 2 Hysteresis Alarm 3 Type Alarm 3 Hysteresis Transfer Output Type Linear Transfer Output Lower Limit Linear Current Output Linear Bank Numbers Used Event Input Assignment 2 Event Input Assignment 3 Closed/Floating otor Calibration Travel Time ove to Advaned Funtion Setting Level: Displayed when initial setting/ ommuniations protet is set to. ove by setting password ( 69). 64

65 Power anual Control Level -U (48 x 48 mm) Protet Level Operation Level Adjustment Level Bank Setting Level PID Setting Level onitor/setting Item Level Initial Setting Level Advaned Funtion Setting Level Setting Level Press the O Key for at least s. Advaned Funtion Setting Level init spru m rest a sbn n-o sb2n n-o sb3n n-o hbu on hbl hbh Heater Burnout Hysteresis. st-b 5. α alfa.65 at-g. at-h.8 lma 2. inf. pvad Parameter Initialization Ramp Time Unit Standby Sequene Reset Auxiliary Output Open in Alarm Auxiliary Output 2 Open in Alarm Auxiliary Output 3 Open in Alarm HB / Heater Burnout Lath ST Stable Range AT Calulated Gain AT Hysteresis Limit Cyle V Amplitude Input Digital Filter Additional PV Display o-dp ret alt a2lt a3lt prlt 3 sero j on rlrv olr red pv-b 5. aon a2on a3on aof Alarm Delay a2of a3of V Display Automati Display Return Time Alarm Lath Alarm 2 Lath Alarm 3 Lath ove to Protet Level Time Input Error Output Cold Juntion Compensation ethod B Command Logi Swithing PV Change Color PV Stable Band Alarm Delay Alarm 2 Delay Alarm 3 Delay Alarm 2 Delay Alarm 3 Delay istp ins mvse amad on rt hsu on hsl hsh. lba out o out2 Control Output 2 Assignment none rspu rsph Remote Upper Limit 3. rspl -2. sptr rseo pidi pv pidh.5 lbal LBA Level p-db 8.. lbab manl LBA Band 3. sub alm sub2 Auxiliary Output 2 Assignment alm2 sub3 alm3 sel on t-u m Input Shift Type V at Stop and Error Addition Auto/anual Selet Addition RT HS Alarm Use HS Alarm Lath HS Alarm Hysteresis LBA Detetion Time Control Output Assignment Auxiliary Output Assignment Auxiliary Output 3 Assignment (E5AN/E5EN-H only) Charater Selet Soak Time Unit alsp sp-m pmvd pvrp 7 sa ou on ol Heater Overurrent Lath Heater Overurrent oh Hysteresis. pf a-m Alarm Seletion Remote Enable Remote Lower Limit Traking Remote Input Error Output PID Set Automati Seletion Data PID Set Automati Seletion Hysteresis PV Dead Band anual V Limit Enable Diret Setting of Position Proportional V PV Rate of Change Calulation Period Automati Cooling Coeffiient Adjustment Heater Overurrent Use PF Setting pfd pfd2 pfd3 pfd4 pfd5 spdp 4 odsl o pvdp on pvst svst d.ref.25 ram ra2m ra ra2 ra mov onitor/setting Item onitor/setting Item 2 onitor/setting Item 3 onitor/setting Item 4 onitor/setting Item 5 "PV/" Display Sreen Seletion V Display Seletion PV Deimal Point Display PV Status Display Funtion SV Status Display Funtion Display Refresh Period Control Output / Count onitor Control Output 2 / Count onitor Control Output / Count Alarm Set Value Control Output 2 / Count Alarm Set Value / Counter Reset ove to Calibration Level -H (48 x 48 mm) E5EN-H(48 x 96 mm) Operation Safety Preautions 65

66 Safety Preautions -U (48 x 48 mm) -H (48 x 48 mm) E5EN-H(48 x 96 mm)!cauti Do not touh the terminals while power is being supplied. Doing so may oasionally result in minor injury due to eletri shok. Do not allow piees of metal, wire lippings, or fine metalli shavings or filings from installation to enter the produt. Doing so may oasionally result in eletri shok, fire, or malfuntion. Do not use the produt where subjet to flammable or explosive gas. Otherwise, minor injury from explosion may oasionally our. Do not leave the able for the Support Software onneted to the produt. alfuntion may our due to noise in the able. Do not use the Temperature Controller or Conversion Cable if it is damaged. Doing so may oasionally result in minor eletri shok or fire. Never disassemble, modify, or repair the produt or touh any of the internal parts. inor eletri shok, fire, or malfuntion may oasionally our. CAUTI - Risk of Fire and Eletri Shok a) This produt is UL listed as Open Type Proess Control Equipment. It must be mounted in an enlosure that does not allow fire to esape externally. b) ore than one disonnet swith may be required to de-energize the equipment before serviing the produt. ) Signal s are SELV, limited energy. d) Caution: To redue the risk of fire or eletri shok, do not interonnet the s of different Class 2 iruits. 2 If the relays are used past their life expetany, ontat fusing or burning may oasionally our. Always onsider the appliation onditions and use the relays within their rated load and eletrial life expetany. The life expetany of relays varies onsiderably with the load and swithing onditions. Tighten the terminal srews to between.74 and.9 N m. 3 Loose srews may oasionally result in fire. Set the parameters of the produt so that they are suitable for the system being ontrolled. If they are not suitable, unexpeted operation may oasionally result in property damage or aidents. A malfuntion in the produt may oasionally make ontrol operations impossible or prevent alarm s, resulting in property damage. To maintain safety in the event of malfuntion of the produt, take appropriate safety measures, suh as installing a monitoring devie on a separate line. A semiondutor is used in the setion of long-life relays. If exessive noise or surge is impressed on the terminals, a short-iruit failure is likely to our. If the remains shorted, fire will our due to overheating of the heater or other ause. Take measures in the overall system to prevent exessive temperature inrease and to prevent fire from spreading. Do not allow piees of metal or wire uttings to get inside the able onnetor for the Support Software. Failure to do so may oasionally result in minor eletri shok, fire, or damage to equipment. Do not allow dust and dirt to ollet between the pins in the onnetor on the Conversion Cable. Failure to do so may oasionally result in fire. When inserting the body of the Temperature Controller into the ase, onfirm that the hooks on the top and bottom are seurely engaged with the ase. If the body of the Temperature Controller is not inserted properly, faulty ontat in the terminal setion or redued water resistane may oasionally result in fire or malfuntion. When onneting the Control Output Unit to the soket, press it in until there is no gap between the Control Output Unit and the soket. Otherwise ontat faults in the onnetor pins may oasionally result in fire or malfuntion.. An SELV iruit is one separated from the power supply with double insulation or reinfored insulation, that does not exeed 3 V r.m.s. and 42.4 V peak or 6 VDC. 2. A lass 2 power supply is one tested and ertified by UL as having the urrent and voltage of the seondary restrited to speifi levels. 3. The tightening torque for -U is.5 N m. Preautions for Safe Use Be sure to observe the following preautions to prevent malfuntion or adverse affets on the performane or funtionality of the produt. Not doing so may oasionally result in faulty operation.. This produt is speifially designed for indoor use only. Do not use this produt in the following plaes: Plaes diretly subjet to heat radiated from heating equipment. Plaes subjet to splashing liquid or oil atmosphere. Plaes subjet to diret sunlight. Plaes subjet to dust or orrosive gas (in partiular, sulfide gas and ammonia gas). Plaes subjet to intense temperature hange. Plaes subjet to iing and ondensation. Plaes subjet to vibration and large shoks. 2. Use and store the produt within the rated ambient temperature and humidity. Gang-mounting two or more Temperature Controllers, or mounting Temperature Controllers above eah other may ause heat to build up inside the Temperature Controllers, whih will shorten their servie life. In suh a ase, use fored ooling by fans or other means of air ventilation to ool down the Temperature Controllers. 3. To allow heat to esape, do not blok the area around the produt. Do not blok the ventilation holes on the produt. 4. Be sure to wire properly with orret polarity of terminals. 5. Use the speified size (3.5, width 7.2 mm or less) rimped terminals for wiring. To onnet bare wires to the terminal blok, use stranded or solid opper wires with a gage of AWG24 to AWG4 (equal to a ross-setional area of.25 to 2.8 mm 2 ). (The stripping length is 5 to 6 mm.) Up to two wires of the same size and type or two rimp terminals an be inserted into a single terminal. 6. Do not wire the terminals that are not used. 7. To avoid indutive noise, keep the wiring for the produt s terminal blok away from power ables arry high voltages or large urrents. Also, do not wire power lines together with or parallel to produt wiring. Using shielded ables and using separate onduits or duts is reommended. Attah a surge suppressor or noise filter to peripheral devies that generate noise (in partiular, motors, transformers, solenoids, magneti oils, or other equipment that have an indutane omponent). When a noise filter is used at the power supply, first hek the voltage or urrent, and attah the noise filter as lose as possible to the produt. Allow as muh spae as possible between the produt and devies that generate powerful high frequenies (high-frequeny welders, high-frequeny sewing mahines, et.) or surge. 8. Use this produt within the rated load and power supply. 9. ake sure that the rated voltage is attained within two seonds of turning the power using a swith or relay ontat. If the voltage is applied gradually, the power may not be reset or malfuntions may our..ake sure that the Temperature Controller has 3 minutes or more to warm up after turning the power before starting atual ontrol operations to ensure the orret temperature display. 66

67 exeuting self-tuning, turn power to the load (e.g., heater) at the same time as or before supplying power to the produt. If power is turned to the produt before turning power to the load, self-tuning will not be performed properly and optimum ontrol will not be ahieved. 2.A swith or iruit breaker must be provided lose to the produt. The swith or iruit breaker must be within easy reah of the operator, and must be marked as a disonneting means for this unit. 3.Always turn the power supply before pulling out the interior of the produt, and never touh nor apply shok to the terminals or eletroni omponents. When inserting the interior of the produt, do not allow the eletroni omponents to touh the ase. 4.Do not use paint thinner or similar hemial to lean with. Use standard grade alohol. 5.Design the system (e.g., ontrol panel) onsidering the 2 seonds of delay that the produt's to be set after power. 6.The may turn when shifting to ertain levels. Take this into onsideration when performing ontrol. 7.The number of EEPRO write operations is limited. Therefore, use RA write mode when frequently overwriting data during ommuniations or other operations. 8.Always touh a grounded piee of metal before touhing the Temperature Controller to disharge stati eletriity from your body. 9.Do not remove the terminal blok. Doing so may result in failure or malfuntion. 2.Control s that are voltage s are not isolated from the internal iruits. When using a grounded thermoouple, do not onnet any of the ontrol terminals to ground. (Doing so may result in an unwanted iruit path, ausing error in the measured temperature.) 2.When replaing the body of the Temperature Controller, hek the ondition of the terminals. If orroded terminals are used, ontat failure in the terminals may ause the temperature inside the Temperature Controller to inrease, possibly resulting in fire. If the terminals are orroded, replae the ase as well. 22.Use suitable tools when taking the Temperature Controller apart for disposal. Sharp parts inside the Temperature Controller may ause injury. 23.Before onneting an Output Unit, onfirm the speifiations and thoroughly read relevant information in the datasheet and manual for the Temperature Controller. 24.Chek the orientation of the onnetors on the Conversion Cable before onneting the Conversion Cable. Do not fore a onnetor if it does not onnet smoothly. Using exessive fore may damage the onnetor. 25.Do not plae heavy objet on the Conversion Cable, bend the able past its natural bending radius, or pull on the able with undue fore. 26.Do not onnet or disonnet the Conversion Cable while ommuniations are in progress. Produt faults or malfuntion may our. 27.ake sure that the Conversion Cable's metal omponents are not touhing the external power terminals. 28.Do not touh the onnetors on the Conversion Cable with wet hands. Eletrial shok may result. 29.Before using infrared ommuniations, orretly attah the enlosed ounting Adapter to the able for the Support Software. When onneting the infrared port on the able to the Support Software into the Adapter, insert the onnetor to the speified line. may not be possible if the onnetor is not onneted properly. Preautions for Corret Use Servie Life. Use the produt within the following temperature and humidity ranges: Temperature: to 55 C (with no iing or ondensation) Humidity: 25% to 85% If the produt is installed inside a ontrol board, the ambient temperature must be kept to under 55 C, inluding the temperature around the produt. 2. The servie life of eletroni devies like Temperature Controllers is determined not only by the number of times the relay is swithed but also by the servie life of internal eletroni omponents. Component servie life is affeted by the ambient temperature: the higher the temperature, the shorter the servie life and, the lower the temperature, the longer the servie life. Therefore, the servie life an be extended by lowering the temperature of the Temperature Controller. 3. When two or more Temperature Controllers are mounted horizontally lose to eah other or vertially next to one another, the internal temperature will inrease due to heat radiated by the Temperature Controllers and the servie life will derease. In suh a ase, use fored ooling by fans or other means of air ventilation to ool down the Temperature Controllers. When providing fored ooling, however, be areful not to ool down the terminals setions alone to avoid measurement errors. easurement Auray. When extending or onneting the thermoouple lead wire, be sure to use ompensating wires that math the thermoouple types. 2. When extending or onneting the lead wire of the platinum resistane thermometer, be sure to use wires that have low resistane and keep the resistane of the three lead wires the same. 3. ount the produt so that it is horizontally level. 4. If the measurement auray is low, hek to see if shift has been set orretly. Waterproofing The degree of protetion is as shown below. Setions without any speifiation on their degree of protetion or those with IP@ are not waterproof. Front panel: IP66 Rear ase: IP2, Terminal setion: IP (-U: Front panel: IP5, rear ase: IP2, terminals: IP) Operating Preautions. It takes approximately two seonds for the s to turn from after the power supply is turned. Due onsideration must be given to this time when inorporating Temperature Controllers in a sequene iruit. 2. When using self-tuning, turn power for the load (e.g., heater) at the same time as or before supplying power to the Temperature Controller. If power is turned for the Temperature Controller before turning power for the load, self-tuning will not be performed properly and optimum ontrol will not be ahieved. 3. When starting operation after the Temperature Controller has warmed up, turn the power and then turn it again at the same time as turning power for the load. (Instead of turning the Temperature Controller and again, swithing from STOP mode to RUN mode an also be used.) 4. Avoid using the Controller in plaes near a radio, television set, or wireless installing. These devies an ause radio disturbanes whih adversely affet the performane of the Controller. Others. The disk that is inluded with the Conversion Cable is designed for a omputer CD-RO driver. Never attempt to play the disk in a general-purpose audio player. 2. Do not onnet or disonnet the Conversion Cable onnetor repeatedly over a short period of time. The omputer may malfuntion. 3. After onneting the Conversion Cable to the omputer, hek the CO port number before starting ommuniations. The omputer requires time to reognize the able onnetion. This delay does not indiate failure. 4. Do not onnet the Conversion Cable through a USB hub. Doing so may damage the Conversion Cable. 5. Do not use an extension able to extend the Conversion Cable length when onneting to the omputer. Doing so may damage the Conversion Cable. 6. The E5AN-H/E5EN-H use the same port for ommuniations through the infrared port and the Support Software port. Do not attempt to use ommuniations through the Support Software port when the infrared port is being used. -U (48 x 48 mm) -H (48 x 48 mm) E5EN-H(48 x 96 mm) Operation Safety Preautions 67

68 -U (48 x 48 mm) -H (48 x 48 mm) E5EN-H(48 x 96 mm) ounting ounting to a Panel For waterproof mounting, waterproof paking must be installed on the Controller. Waterproofing is not possible when group mounting several Controllers. Waterproof paking is not neessary when there is no need for the waterproofing funtion. E53-COV7 Terminal Cover (Aessory) Adapter (Aessory) Waterproof paking (Aessory) Panel. The Panel ounting Adapter is also inluded with the -U. There is no waterproof paking inluded with the -U. 2. Insert the /-U into the mounting hole in the panel. 3. Push the adapter from the terminals up to the panel, and temporarily fasten the /-U. 4. Tighten the two fastening srews on the adapter. Alternately tighten the two srews little by little to maintain a balane. Tighten the srews to a torque of.29 to.39 N m. E5EN/E5AN E53-COV6 Terminal Cover (Aessory) E53-COV6 Terminal Cover (Aessory) ounting Braket (Aessory) Waterproof paking (Aessory) ounting Braket (Aessory) Waterproof paking (Aessory) Order the P2CF- or P3GA- Soket separately. -U For Front-mounting Soket (Panel mounting is also possible.) Panel Panel E5AN E5EN. Insert the E5AN/E5EN into the square mounting hole in the panel (thikness: to 8 mm). Attah the ounting Brakets provided with the produt to the mounting grooves on the top and bottom surfaes of the rear ase. 2. Use a rathet to alternately tighten the srews on the top and bottom ounting Brakets little by little to maintain balane, until the rathet turns freely. ounting the Terminal Cover ake sure that the UP mark is faing up, and then attah the E53- COV7 Terminal Cover to the holes on the top and bottom of the Temperature Controller. E5AN/E5EN Slightly bend the E53-COV6 Terminal Cover to attah it to the terminal blok as shown in the following diagram. The Terminal Cover annot be attahed in the opposite diretion. Slightly bend the E53-COV6 Terminal Cover in the diretion shown by the arrows to attah it to the terminal blok. E53-COV6 Terminal Cover (Aessory) Removing the Temperature Controller from the Case The Temperature Controller an be removed from the ase to perform maintenane without removing the terminal leads. This is possible for only the, E5AN, and E5EN, and not for the -U. Chek the speifiations of the ase and Temperature Controller before removing the Temperature Controller from the ase. Tool insertion hole (). Insert a flat-blade srewdriver into the two tool insertion holes (one on the top and one on the bottom) to release the hooks. 2. Insert the flat-blade srewdriver in the gap between the front panel and rear ase, and pull out the front panel slightly. Hold the top and bottom of the front panel and arefully pull it out toward you, without applying unneessary fore. 3. When inserting the body of the Temperature Controller into the ase, make sure the PCBs are parallel to eah other, make sure that the sealing rubber is in plae, and press the toward the rear ase into position. While pushing the into plae, push down on the hooks on the top and bottom surfaes of the rear ase so that the hooks are seurely loked in plae. Be sure that eletroni omponents do not ome into ontat with the ase. () (2) (3) Flat-blade srewdriver (Unit: mm)

69 E5AN/E5EN Tool insertion hole () Tool insertion hole () -U (48 x 48 mm) E5AN. Insert a flat-blade srewdriver into the two tool insertion holes (one on the top and one on the bottom) to release the hooks. 2. Insert the flat-blade srewdriver in the gap between the front panel and rear ase (two on the top and two on the bottom), and use it to pry and pull out the front panel slightly. Then, pull out on the front panel gripping both sides. Be sure not to impose exessive fore on the panel. 3. When inserting the body of the Temperature Controller into the ase, make sure the PCBs are parallel to eah other, make sure that the sealing rubber is in plae, and press the E5AN/E5EN toward the rear ase until it snaps into position. While pressing the E5AN/E5EN into plae, press down on the hooks on the top and bottom surfaes of the rear ase so that the hooks seurely lok in plae. ake sure that eletroni omponents do not ome into ontat with the ase. Preautions when Wiring Separate leads and power lines in order to prevent external noise. Use wires with a gage of AWG24 (ross-setional area:.25 mm 2 ) to AWG4 (ross-setional area: 2.8 mm 2 ) twistedpair able (stripping length: 5 to 6 mm). Use rimp terminals when wiring the terminals. Tighten the terminal srews to a torque of.74 to.9 N m, however the terminal srews on the -U must be tightened to a torque of.5 N m. Use the following types of rimp terminals for 3.5 srews. () (2) (3) 7.2 mm max. E5EN (2) (3) () -H (48 x 48 mm) E5EN-H(48 x 96 mm) 7.2 mm max. Do not remove the terminal blok. Doing so will result in malfuntion or failure. Operation Safety Preautions 69

70 C-Thermo Support Software Ver. 4. EST2-2C-V4 onitoring/setting Support Software for /CN-H, E5AN/AN-H, E5EN/EN-H, E5ZN, and EJ Temperature Controllers Enabling Faster Parameter Setup, Devie Adjustment, and aintenane Enables editing and bath-downloading parameters from a personal omputer, reduing the work required to set parameters. Usability is improved with table-formatted parameter editing from version. 4.. Supports Trend onitoring: onitor data (PV,,V,PID parameter, Alarm /, et.) for up to 3 E5@N/@N-H Temperature Controllers. Connet up to 64 EJN, 7 EJG, or 6 E5ZN Temperature Controllers. (The Temperature Controllers must be from the same series.) Supports parameter masks to hide parameters unneessary to display. (Supported only by the E5@N/@N-H and E5@R/@R-T). Logi operations enable setting s from external s (event s) or temperature status, s to external s (ontrol or auxiliary s), and hanging operating status with / delays. (Supported only by the E5@N/@N-H). Easy adjustment of ontrol performane by fine-tuning. Fine-tuning instruts the C-Thermo to alulate a PID parameters by diretly ting ommands to improve response. Ordering Information List of odels Name C-Thermo Support Software odel EST2-2C-V4 Speifiations Compatible devies Personal omputer system requirements Temperature Controllers OS CPU emory Harddisk CD-RO onitor Connetion method ports (available from April 24) E5AN, E5EN (available from Feb 25), -H, E5AN-H, E5EN-H E5AR, E5ER E5AR-T, E5ER-T E5ZN EJN-TC4, EJN-TC2, EJN-HFU EJG-TC4, EJG-TC2, EJG-HFU G3ZA (only when onneted to EJN-TC4, EJN-TC2, EJG-TC4, EJG-TC2) Note: odels with DevieNet ommuniations are not supported. Windows 2 (servie pak 3 or higher), P, or Vista (Japanese or English version) 3 Hz min. 28 B min. 3 B min. available spae One CD-RO drive min. SVGA (8 6) min. RS-232C port, or USB port, port min. An E58-CIFQ USB-Serial Conversion Cable is required to onnet a omputer to the setup tool port the E5@N, E5@N-H, or EJ. A K3SC Interfae Converter is used to onnet a omputer to models with RS-422/RS-485 ommuniations. An E58-CIFIR USB-Infrared Conversion Cable is required to wirelessly onnet a omputer to models with infrared ommuniations (E5AN-H or E5EN-H). 7